IPv6 multicast and link-local addresses require special handling by the
VRF driver:
1. Rather than using the VRF device index and full FIB lookups,
packets to/from these addresses should use direct FIB lookups based on
the VRF device table.
2. fail sends/receives on a VRF device to/from a multicast address
(e.g, make ping6 ff02::1%<vrf> fail)
3. move the setting of the flow oif to the first dst lookup and revert
the change in icmpv6_echo_reply made in ca254490c8 ("net: Add VRF
support to IPv6 stack"). Linklocal/mcast addresses require use of the
skb->dev.
With this change connections into and out of a VRF enslaved device work
for multicast and link-local addresses work (icmp, tcp, and udp)
e.g.,
1. packets into VM with VRF config:
ping6 -c3 fe80::e0:f9ff:fe1c:b974%br1
ping6 -c3 ff02::1%br1
ssh -6 fe80::e0:f9ff:fe1c:b974%br1
2. packets going out a VRF enslaved device:
ping6 -c3 fe80::18f8:83ff:fe4b:7a2e%eth1
ping6 -c3 ff02::1%eth1
ssh -6 root@fe80::18f8:83ff:fe4b:7a2e%eth1
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
L3 master devices are virtual devices similar to the loopback
device. Link local and multicast routes for these devices do
not make sense. The ipv6 addrconf code already skips adding a
linklocal address; do the same for the mcast route.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a corner case in which udp packets belonging to a same
flow are hashed to different socket when hslot->count changes from 10
to 11:
1) When hslot->count <= 10, __udp_lib_lookup() searches udp_table->hash,
and always passes 'daddr' to udp_ehashfn().
2) When hslot->count > 10, __udp_lib_lookup() searches udp_table->hash2,
but may pass 'INADDR_ANY' to udp_ehashfn() if the sockets are bound to
INADDR_ANY instead of some specific addr.
That means when hslot->count changes from 10 to 11, the hash calculated by
udp_ehashfn() is also changed, and the udp packets belonging to a same
flow will be hashed to different socket.
This is easily reproduced:
1) Create 10 udp sockets and bind all of them to 0.0.0.0:40000.
2) From the same host send udp packets to 127.0.0.1:40000, record the
socket index which receives the packets.
3) Create 1 more udp socket and bind it to 0.0.0.0:44096. The number 44096
is 40000 + UDP_HASH_SIZE(4096), this makes the new socket put into the
same hslot as the aformentioned 10 sockets, and makes the hslot->count
change from 10 to 11.
4) From the same host send udp packets to 127.0.0.1:40000, and the socket
index which receives the packets will be different from the one received
in step 2.
This should not happen as the socket bound to 0.0.0.0:44096 should not
change the behavior of the sockets bound to 0.0.0.0:40000.
It's the same case for IPv6, and this patch also fixes that.
Signed-off-by: Su, Xuemin <suxm@chinanetcenter.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Tom Herbert <tom@herbertland.com>
Fixes: 4068579e1e ("net: Implmement RFC 6936 (zero RX csums for UDP/IPv6")
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Fixes: 1d13a96c74 ("ipv6: tcp: fix flowlabel value in ACK messages send from TIME_WAIT")
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 ping socket error handler doesn't correctly convert the new 32 bit
mtu to host endianness before using.
Cc: Lorenzo Colitti <lorenzo@google.com>
Fixes: 6d0bfe2261 ("net: ipv6: Add IPv6 support to the ping socket.")
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In IPv6 the ToS values are part of the flowlabel in flowi6 and get
extracted during fib rule lookup, but we forgot to correctly initialize
the flowlabel before the routing lookup.
Reported-by: <liam.mcbirnie@boeing.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/sched/act_police.c
net/sched/sch_drr.c
net/sched/sch_hfsc.c
net/sched/sch_prio.c
net/sched/sch_red.c
net/sched/sch_tbf.c
In net-next the drop methods of the packet schedulers got removed, so
the bug fixes to them in 'net' are irrelevant.
A packet action unload crash fix conflicts with the addition of the
new firstuse timestamp.
Signed-off-by: David S. Miller <davem@davemloft.net>
Frank Kellermann reported a kernel crash with 4.5.0 when IPv6 is
disabled at boot using the kernel option ipv6.disable=1. Using
current net-next with the boot option:
$ ip link add red type vrf table 1001
Generates:
[12210.919584] BUG: unable to handle kernel NULL pointer dereference at 0000000000000748
[12210.921341] IP: [<ffffffff814b30e3>] fib6_get_table+0x2c/0x5a
[12210.922537] PGD b79e3067 PUD bb32b067 PMD 0
[12210.923479] Oops: 0000 [#1] SMP
[12210.924001] Modules linked in: ipvlan 8021q garp mrp stp llc
[12210.925130] CPU: 3 PID: 1177 Comm: ip Not tainted 4.7.0-rc1+ #235
[12210.926168] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
[12210.928065] task: ffff8800b9ac4640 ti: ffff8800bacac000 task.ti: ffff8800bacac000
[12210.929328] RIP: 0010:[<ffffffff814b30e3>] [<ffffffff814b30e3>] fib6_get_table+0x2c/0x5a
[12210.930697] RSP: 0018:ffff8800bacaf888 EFLAGS: 00010202
[12210.931563] RAX: 0000000000000748 RBX: ffffffff81a9e280 RCX: ffff8800b9ac4e28
[12210.932688] RDX: 00000000000000e9 RSI: 0000000000000002 RDI: 0000000000000286
[12210.933820] RBP: ffff8800bacaf898 R08: ffff8800b9ac4df0 R09: 000000000052001b
[12210.934941] R10: 00000000657c0000 R11: 000000000000c649 R12: 00000000000003e9
[12210.936032] R13: 00000000000003e9 R14: ffff8800bace7800 R15: ffff8800bb3ec000
[12210.937103] FS: 00007faa1766c700(0000) GS:ffff88013ac00000(0000) knlGS:0000000000000000
[12210.938321] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[12210.939166] CR2: 0000000000000748 CR3: 00000000b79d6000 CR4: 00000000000406e0
[12210.940278] Stack:
[12210.940603] ffff8800bb3ec000 ffffffff81a9e280 ffff8800bacaf8c8 ffffffff814b3135
[12210.941818] ffff8800bb3ec000 ffffffff81a9e280 ffffffff81a9e280 ffff8800bace7800
[12210.943040] ffff8800bacaf8f0 ffffffff81397c88 ffff8800bb3ec000 ffffffff81a9e280
[12210.944288] Call Trace:
[12210.944688] [<ffffffff814b3135>] fib6_new_table+0x24/0x8a
[12210.945516] [<ffffffff81397c88>] vrf_dev_init+0xd4/0x162
[12210.946328] [<ffffffff814091e1>] register_netdevice+0x100/0x396
[12210.947209] [<ffffffff8139823d>] vrf_newlink+0x40/0xb3
[12210.948001] [<ffffffff814187f0>] rtnl_newlink+0x5d3/0x6d5
...
The problem above is due to the fact that the fib hash table is not
allocated when IPv6 is disabled at boot.
As for the VRF driver it should not do any IPv6 initializations if IPv6
is disabled, so it needs to know if IPv6 is disabled at boot. The disable
parameter is private to the IPv6 module, so provide an accessor for
modules to determine if IPv6 was disabled at boot time.
Fixes: 35402e3136 ("net: Add IPv6 support to VRF device")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipip6_tunnel_xmit() is called immediately after checking that
skb->protocol is htons(ETH_P_IPV6) so there is no need
to check it a second time.
Found by inspection.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ip6 GRE tap device should not be forced to down state to change
the mac address and should allow live address change for tap device
similar to ipv4 gre.
Signed-off-by: Shweta Choudaha <schoudah@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ip6 GRE tap device should not be forced to down state to change
the mac address and should allow live address change for tap device
similar to ipv4 gre.
Signed-off-by: Shweta Choudaha <schoudah@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, VRFs require 1 oif and 1 iif rule per address family per
VRF. As the number of VRF devices increases it brings scalability
issues with the increasing rule list. All of the VRF rules have the
same format with the exception of the specific table id to direct the
lookup. Since the table id is available from the oif or iif in the
loopup, the VRF rules can be consolidated to a single rule that pulls
the table from the VRF device.
This patch introduces a new rule attribute l3mdev. The l3mdev rule
means the table id used for the lookup is pulled from the L3 master
device (e.g., VRF) rather than being statically defined. With the
l3mdev rule all of the basic VRF FIB rules are reduced to 1 l3mdev
rule per address family (IPv4 and IPv6).
If an admin wishes to insert higher priority rules for specific VRFs
those rules will co-exist with the l3mdev rule. This capability means
current VRF scripts will co-exist with this new simpler implementation.
Currently, the rules list for both ipv4 and ipv6 look like this:
$ ip ru ls
1000: from all oif vrf1 lookup 1001
1000: from all iif vrf1 lookup 1001
1000: from all oif vrf2 lookup 1002
1000: from all iif vrf2 lookup 1002
1000: from all oif vrf3 lookup 1003
1000: from all iif vrf3 lookup 1003
1000: from all oif vrf4 lookup 1004
1000: from all iif vrf4 lookup 1004
1000: from all oif vrf5 lookup 1005
1000: from all iif vrf5 lookup 1005
1000: from all oif vrf6 lookup 1006
1000: from all iif vrf6 lookup 1006
1000: from all oif vrf7 lookup 1007
1000: from all iif vrf7 lookup 1007
1000: from all oif vrf8 lookup 1008
1000: from all iif vrf8 lookup 1008
...
32765: from all lookup local
32766: from all lookup main
32767: from all lookup default
With the l3mdev rule the list is just the following regardless of the
number of VRFs:
$ ip ru ls
1000: from all lookup [l3mdev table]
32765: from all lookup local
32766: from all lookup main
32767: from all lookup default
(Note: the above pretty print of the rule is based on an iproute2
prototype. Actual verbage may change)
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At present we perform an xfrm_lookup() for each UDPv6 message we
send. The lookup involves querying the flow cache (flow_cache_lookup)
and, in case of a cache miss, creating an XFRM bundle.
If we miss the flow cache, we can end up creating a new bundle and
deriving the path MTU (xfrm_init_pmtu) from on an already transformed
dst_entry, which we pass from the socket cache (sk->sk_dst_cache) down
to xfrm_lookup(). This can happen only if we're caching the dst_entry
in the socket, that is when we're using a connected UDP socket.
To put it another way, the path MTU shrinks each time we miss the flow
cache, which later on leads to incorrectly fragmented payload. It can
be observed with ESPv6 in transport mode:
1) Set up a transformation and lower the MTU to trigger fragmentation
# ip xfrm policy add dir out src ::1 dst ::1 \
tmpl src ::1 dst ::1 proto esp spi 1
# ip xfrm state add src ::1 dst ::1 \
proto esp spi 1 enc 'aes' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b
# ip link set dev lo mtu 1500
2) Monitor the packet flow and set up an UDP sink
# tcpdump -ni lo -ttt &
# socat udp6-listen:12345,fork /dev/null &
3) Send a datagram that needs fragmentation with a connected socket
# perl -e 'print "@" x 1470 | socat - udp6:[::1]:12345
2016/06/07 18:52:52 socat[724] E read(3, 0x555bb3d5ba00, 8192): Protocol error
00:00:00.000000 IP6 ::1 > ::1: frag (0|1448) ESP(spi=0x00000001,seq=0x2), length 1448
00:00:00.000014 IP6 ::1 > ::1: frag (1448|32)
00:00:00.000050 IP6 ::1 > ::1: ESP(spi=0x00000001,seq=0x3), length 1272
(^ ICMPv6 Parameter Problem)
00:00:00.000022 IP6 ::1 > ::1: ESP(spi=0x00000001,seq=0x5), length 136
4) Compare it to a non-connected socket
# perl -e 'print "@" x 1500' | socat - udp6-sendto:[::1]:12345
00:00:40.535488 IP6 ::1 > ::1: frag (0|1448) ESP(spi=0x00000001,seq=0x6), length 1448
00:00:00.000010 IP6 ::1 > ::1: frag (1448|64)
What happens in step (3) is:
1) when connecting the socket in __ip6_datagram_connect(), we
perform an XFRM lookup, miss the flow cache, create an XFRM
bundle, and cache the destination,
2) afterwards, when sending the datagram, we perform an XFRM lookup,
again, miss the flow cache (due to mismatch of flowi6_iif and
flowi6_oif, which is an issue of its own), and recreate an XFRM
bundle based on the cached (and already transformed) destination.
To prevent the recreation of an XFRM bundle, avoid an XFRM lookup
altogether whenever we already have a destination entry cached in the
socket. This prevents the path MTU shrinkage and brings us on par with
UDPv4.
The fix also benefits connected PINGv6 sockets, another user of
ip6_sk_dst_lookup_flow(), who also suffer messages being transformed
twice.
Joint work with Hannes Frederic Sowa.
Reported-by: Jan Tluka <jtluka@redhat.com>
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting up ILA in a router we noticed that the the encapsulation
is invoked twice: once in the route input path and again upon route
output. To resolve this we add a flag set_csum_neutral for the
ila_update_ipv6_locator. If this flag is set and the checksum
neutral bit is also set we assume that checksum-neutral translation
has already been performed and take no further action. The
flag is set only in ila_output path. The flag is not set for ila_input and
ila_xlat.
Tested:
Used 3 netns to set to emulate a router and two hosts. The router
translates SIR addresses between the two destinations in other two netns.
Verified ping and netperf are functional.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for locally originated traffic to VRF-local IPv6 addresses.
Similar to IPv4 a local dst is set on the skb and the packet is
reinserted with a call to netif_rx. With this patch, ping, tcp and udp
packets to a local IPv6 address are successfully routed:
$ ip addr show dev eth1
4: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master red state UP group default qlen 1000
link/ether 02:e0:f9:1c:b9:74 brd ff:ff:ff:ff:ff:ff
inet 10.100.1.1/24 brd 10.100.1.255 scope global eth1
valid_lft forever preferred_lft forever
inet6 2100:1::1/120 scope global
valid_lft forever preferred_lft forever
inet6 fe80::e0:f9ff:fe1c:b974/64 scope link
valid_lft forever preferred_lft forever
$ ping6 -c1 -I red 2100:1::1
ping6: Warning: source address might be selected on device other than red.
PING 2100:1::1(2100:1::1) from 2100:1::1 red: 56 data bytes
64 bytes from 2100:1::1: icmp_seq=1 ttl=64 time=0.098 ms
ip6_input is exported so the VRF driver can use it for the dst input
function. The dst_alloc function for IPv4 defaults to setting the input and
output functions; IPv6's does not. VRF does not need to duplicate the Rx path
so just export the ipv6 input function.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The v6 tcp stats scan do not provide TLP and ER timer information
correctly like the v4 version . This patch fixes that.
Fixes: 6ba8a3b19e ("tcp: Tail loss probe (TLP)")
Fixes: eed530b6c6 ("tcp: early retransmit")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_gso_network_seglen is not enough for checking fragment sizes if
skb is using GSO_BY_FRAGS as we have to check frag per frag.
This patch introduces skb_gso_validate_mtu, based on the former, which
will wrap the use case inside it as all calls to skb_gso_network_seglen
were to validate if it fits on a given TMU, and improve the check.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Tested-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Moore tracked a regression caused by a recent commit, which
mistakenly assumed that sk_filter() could be avoided if socket
had no current BPF filter.
The intent was to avoid udp_lib_checksum_complete() overhead.
But sk_filter() also checks skb_pfmemalloc() and
security_sock_rcv_skb(), so better call it.
Fixes: e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Paul Moore <paul@paul-moore.com>
Tested-by: Paul Moore <paul@paul-moore.com>
Tested-by: Stephen Smalley <sds@tycho.nsa.gov>
Cc: samanthakumar <samanthakumar@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree,
they are:
1) Fix incorrect timestamp in nfnetlink_queue introduced when addressing
y2038 safe timestamp, from Florian Westphal.
2) Get rid of leftover conntrack definition from the previous merge
window, oneliner from Florian.
3) Make nf_queue handler pernet to resolve race on dereferencing the
hook state structure with netns removal, from Eric Biederman.
4) Ensure clean exit on unregistered helper ports, from Taehee Yoo.
5) Restore FLOWI_FLAG_KNOWN_NH in nf_dup_ipv6. This got lost while
generalizing xt_TEE to add packet duplication support in nf_tables,
from Paolo Abeni.
6) Insufficient netlink NFTA_SET_TABLE attribute check in
nf_tables_getset(), from Phil Turnbull.
7) Reject helper registration on duplicated ports via modparams.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The Kconfig options I added to work around broken compilation ended
up screwing up things more, as I used the wrong symbol to control
compilation of the file, resulting in IPv6 fou support to never be built
into the kernel.
Changing CONFIG_NET_FOU_IPV6_TUNNELS to CONFIG_IPV6_FOU fixes that
problem, I had renamed the symbol in one location but not the other,
and as the file is never being used by other kernel code, this did not
lead to a build failure that I would have caught.
After that fix, another issue with the same patch becomes obvious, as we
'select INET6_TUNNEL', which is related to IPV6_TUNNEL, but not the same,
and this can still cause the original build failure when IPV6_TUNNEL is
not built-in but IPV6_FOU is. The fix is equally trivial, we just need
to select the right symbol.
I have successfully build 350 randconfig kernels with this patch
and verified that the driver is now being built.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Valentin Rothberg <valentinrothberg@gmail.com>
Fixes: fabb13db44 ("fou: add Kconfig options for IPv6 support")
Signed-off-by: David S. Miller <davem@davemloft.net>
With the commit 48e8aa6e31 ("ipv6: Set FLOWI_FLAG_KNOWN_NH at
flowi6_flags") ip6_pol_route() callers were asked to to set the
FLOWI_FLAG_KNOWN_NH properly and xt_TEE was updated accordingly,
but with the later refactor in commit bbde9fc182 ("netfilter:
factor out packet duplication for IPv4/IPv6") the flowi6_flags
update was lost.
This commit re-add it just before the routing decision.
Fixes: bbde9fc182 ("netfilter: factor out packet duplication for IPv4/IPv6")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
A previous patch added the fou6.ko module, but that failed to link
in a couple of configurations:
net/built-in.o: In function `ip6_tnl_encap_add_fou_ops':
net/ipv6/fou6.c:88: undefined reference to `ip6_tnl_encap_add_ops'
net/ipv6/fou6.c:94: undefined reference to `ip6_tnl_encap_add_ops'
net/ipv6/fou6.c:97: undefined reference to `ip6_tnl_encap_del_ops'
net/built-in.o: In function `ip6_tnl_encap_del_fou_ops':
net/ipv6/fou6.c:106: undefined reference to `ip6_tnl_encap_del_ops'
net/ipv6/fou6.c:107: undefined reference to `ip6_tnl_encap_del_ops'
If CONFIG_IPV6=m, ip6_tnl_encap_add_ops/ip6_tnl_encap_del_ops
are in a module, but fou6.c can still be built-in, and that
obviously fails to link.
Also, if CONFIG_IPV6=y, but CONFIG_IPV6_TUNNEL=m or
CONFIG_IPV6_TUNNEL=n, the same problem happens for a different
reason.
This adds two new silent Kconfig symbols to work around both
problems:
- CONFIG_IPV6_FOU is now always set to 'm' if either CONFIG_NET_FOU=m
or CONFIG_IPV6=m
- CONFIG_IPV6_FOU_TUNNEL is set implicitly when IPV6_FOU is enabled
and NET_FOU_IP_TUNNELS is also turned out, and it will ensure
that CONFIG_IPV6_TUNNEL is also available.
The options could be made user-visible as well, to give additional
room for configuration, but it seems easier not to bother users
with more choice here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: aa3463d65e ("fou: Add encap ops for IPv6 tunnels")
Signed-off-by: David S. Miller <davem@davemloft.net>
In gre6 xmit path, we are sending a GRE packet, so set fl6 proto
to IPPROTO_GRE properly.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creat an ip6gretap interface with an unreachable route,
the MTU is about 14 bytes larger than what was needed.
If the remote address is reachable:
ping6 2001:0:130::1 -c 2
PING 2001:0:130::1(2001:0:130::1) 56 data bytes
64 bytes from 2001:0:130::1: icmp_seq=1 ttl=64 time=1.46 ms
64 bytes from 2001:0:130::1: icmp_seq=2 ttl=64 time=81.1 ms
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we find a socket with encapsulation enabled we should call
the encap_recv function even if just a udp header without payload is
available. The callbacks are responsible for correctly verifying and
dropping the packets.
Also, in case the header validation fails for geneve and vxlan we
shouldn't put the skb back into the socket queue, no one will pick
them up there. Instead we can simply discard them in the respective
encap_recv functions.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses the same issue we had for IPv4 where enabling GRE with
an inner checksum cannot be supported with FOU/GUE due to the fact that
they will jump past the GRE header at it is treated like a tunnel header.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since iptunnel_handle_offloads() is called in all paths we can
probably drop the block in ip6_tnl_xmit that was checking for
skb->encapsulation and resetting the inner headers.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to set dev features, use same values that are used in GREv6.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add a new fou6 module that provides encapsulation
operations for IPv6.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add encap_hlen and ip_tunnel_encap structure to ip6_tnl. Add functions
for getting encap hlen, setting up encap on a tunnel, performing
encapsulation operation.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When performing foo-over-UDP, UDP packets are processed by the
encapsulation handler which returns another protocol to process.
This may result in processing two (or more) protocols in the
loop that are marked as INET6_PROTO_FINAL. The actions taken
for hitting a final protocol, in particular the skb_postpull_rcsum
can only be performed once.
This patch set adds a check of a final protocol has been seen. The
rules are:
- If the final protocol has not been seen any protocol is processed
(final and non-final). In the case of a final protocol, the final
actions are taken (like the skb_postpull_rcsum)
- If a final protocol has been seen (e.g. an encapsulating UDP
header) then no further non-final protocols are allowed
(e.g. extension headers). For more final protocols the
final actions are not taken (e.g. skb_postpull_rcsum).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ip6_input_finish the nexthdr protocol is retrieved from the
next header offset that is returned in the cb of the skb.
This method does not work for UDP encapsulation that may not
even have a concept of a nexthdr field (e.g. FOU).
This patch checks for a final protocol (INET6_PROTO_FINAL) when a
protocol handler returns > 0. If the protocol is not final then
resubmission is performed on nhoff value. If the protocol is final
then the nexthdr is taken to be the return value.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch defines two new GSO definitions SKB_GSO_IPXIP4 and
SKB_GSO_IPXIP6 along with corresponding NETIF_F_GSO_IPXIP4 and
NETIF_F_GSO_IPXIP6. These are used to described IP in IP
tunnel and what the outer protocol is. The inner protocol
can be deduced from other GSO types (e.g. SKB_GSO_TCPV4 and
SKB_GSO_TCPV6). The GSO types of SKB_GSO_IPIP and SKB_GSO_SIT
are removed (these are both instances of SKB_GSO_IPXIP4).
SKB_GSO_IPXIP6 will be used when support for GSO with IP
encapsulation over IPv6 is added.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In several gso_segment functions there are checks of gso_type against
a seemingly arbitrary list of SKB_GSO_* flags. This seems like an
attempt to identify unsupported GSO types, but since the stack is
the one that set these GSO types in the first place this seems
unnecessary to do. If a combination isn't valid in the first
place that stack should not allow setting it.
This is a code simplication especially for add new GSO types.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_hdr() is slightly more expensive than using skb->data in contexts
where we know they point to the same byte.
In receive path, tcp_v4_rcv() and tcp_v6_rcv() are in this situation,
as tcp header has not been pulled yet.
In output path, the same can be said when we just pushed the tcp header
in the skb, in tcp_transmit_skb() and tcp_make_synack()
Also factorize the two checks for tcb->tcp_flags & TCPHDR_SYN in
tcp_transmit_skb() and pass tcp header pointer to tcp_ecn_send(),
so that compiler can further optimize and avoid a reload.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__sock_cmsg_send() might return different error codes, not only -EINVAL.
Fixes: 24025c465f ("ipv4: process socket-level control messages in IPv4")
Fixes: ad1e46a837 ("ipv6: process socket-level control messages in IPv6")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nf_conntrack_core.c fix in 'net' is not relevant in 'net-next'
because we no longer have a per-netns conntrack hash.
The ip_gre.c conflict as well as the iwlwifi ones were cases of
overlapping changes.
Conflicts:
drivers/net/wireless/intel/iwlwifi/mvm/tx.c
net/ipv4/ip_gre.c
net/netfilter/nf_conntrack_core.c
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when creating or updating a route, no check is performed
in both ipv4 and ipv6 code to the hoplimit value.
The caller can i.e. set hoplimit to 256, and when such route will
be used, packets will be sent with hoplimit/ttl equal to 0.
This commit adds checks for the RTAX_HOPLIMIT value, in both ipv4
ipv6 route code, substituting any value greater than 255 with 255.
This is consistent with what is currently done for ADVMSS and MTU
in the ipv4 code.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing an OpenStack configuration using VXLANs I saw the following
call trace:
RIP: 0010:[<ffffffff815fad49>] udp4_lib_lookup_skb+0x49/0x80
RSP: 0018:ffff88103867bc50 EFLAGS: 00010286
RAX: ffff88103269bf00 RBX: ffff88103269bf00 RCX: 00000000ffffffff
RDX: 0000000000004300 RSI: 0000000000000000 RDI: ffff880f2932e780
RBP: ffff88103867bc60 R08: 0000000000000000 R09: 000000009001a8c0
R10: 0000000000004400 R11: ffffffff81333a58 R12: ffff880f2932e794
R13: 0000000000000014 R14: 0000000000000014 R15: ffffe8efbfd89ca0
FS: 0000000000000000(0000) GS:ffff88103fd80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000488 CR3: 0000000001c06000 CR4: 00000000001426e0
Stack:
ffffffff81576515 ffffffff815733c0 ffff88103867bc98 ffffffff815fcc17
ffff88103269bf00 ffffe8efbfd89ca0 0000000000000014 0000000000000080
ffffe8efbfd89ca0 ffff88103867bcc8 ffffffff815fcf8b ffff880f2932e794
Call Trace:
[<ffffffff81576515>] ? skb_checksum+0x35/0x50
[<ffffffff815733c0>] ? skb_push+0x40/0x40
[<ffffffff815fcc17>] udp_gro_receive+0x57/0x130
[<ffffffff815fcf8b>] udp4_gro_receive+0x10b/0x2c0
[<ffffffff81605863>] inet_gro_receive+0x1d3/0x270
[<ffffffff81589e59>] dev_gro_receive+0x269/0x3b0
[<ffffffff8158a1b8>] napi_gro_receive+0x38/0x120
[<ffffffffa0871297>] gro_cell_poll+0x57/0x80 [vxlan]
[<ffffffff815899d0>] net_rx_action+0x160/0x380
[<ffffffff816965c7>] __do_softirq+0xd7/0x2c5
[<ffffffff8107d969>] run_ksoftirqd+0x29/0x50
[<ffffffff8109a50f>] smpboot_thread_fn+0x10f/0x160
[<ffffffff8109a400>] ? sort_range+0x30/0x30
[<ffffffff81096da8>] kthread+0xd8/0xf0
[<ffffffff81693c82>] ret_from_fork+0x22/0x40
[<ffffffff81096cd0>] ? kthread_park+0x60/0x60
The following trace is seen when receiving a DHCP request over a flow-based
VXLAN tunnel. I believe this is caused by the metadata dst having a NULL
dev value and as a result dev_net(dev) is causing a NULL pointer dereference.
To resolve this I am replacing the check for skb_dst(skb)->dev with just
skb->dev. This makes sense as the callers of this function are usually in
the receive path and as such skb->dev should always be populated. In
addition other functions in the area where these are called are already
using dev_net(skb->dev) to determine the namespace the UDP packet belongs
in.
Fixes: 63058308cd ("udp: Add udp6_lib_lookup_skb and udp4_lib_lookup_skb")
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dealing with WCCP in gre6 tunnel, it sets the wrong tpi->protocol,
that is, ETH_P_IP instead of ETH_P_IPV6 for the encapuslated traffic.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not include attribute IFLA_GRE_TOS.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the VRF driver uses the rx_handler to switch the skb device
to the VRF device. Switching the dev prior to the ip / ipv6 layer
means the VRF driver has to duplicate IP/IPv6 processing which adds
overhead and makes features such as retaining the ingress device index
more complicated than necessary.
This patch moves the hook to the L3 layer just after the first NF_HOOK
for PRE_ROUTING. This location makes exposing the original ingress device
trivial (next patch) and allows adding other NF_HOOKs to the VRF driver
in the future.
dev_queue_xmit_nit is exported so that the VRF driver can cycle the skb
with the switched device through the packet taps to maintain current
behavior (tcpdump can be used on either the vrf device or the enslaved
devices).
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Protocol for 4in6 tunnel is IPPROTO_IPIP. This was wrongly changed by
the last cleanup.
CC: Tom Herbert <tom@herbertland.com>
Fixes: 0d3c703a9d ("ipv6: Cleanup IPv6 tunnel receive path")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The handler 'ila_fill_encap_info' adds two attributes: ILA_ATTR_LOCATOR
and ILA_ATTR_CSUM_MODE.
nla_total_size_64bit() must be use for ILA_ATTR_LOCATOR.
Also, do nla_put_u8 instead of nla_put_u64 for ILA_ATTR_CSUM_MODE.
Fixes: f13a82d87b ("ipv6: use nla_put_u64_64bit()")
Fixes: 90bfe662db ("ila: add checksum neutral ILA translations")
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix two spots where o_flags in a tunnel are being compared to GRE_SEQ
instead of TUNNEL_SEQ.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to use adjusted protocol value for setting inner protocol.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRE for IPv6 does not properly translate for GRE flags to tunnel
flags and vice versa. This patch fixes that.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ip6gre_tnl_link_config set t->tun_len and t->hlen correctly for the
configuration. For hard_header_len and mtu calculation include
IPv6 header and encapsulation overhead.
In ip6gre_tunnel_init_common set t->tun_len and t->hlen correctly for
the configuration. Revert to setting hard_header_len instead of
needed_headroom.
Tested:
./ip link add name tun8 type ip6gretap remote \
2401:db00:20:911a:face:0:27:0 local \
2401:db00:20:911a:face:0:25:0 ttl 225
Gives MTU of 1434. That is equal to 1500 - 40 - 14 - 4 - 8.
./ip link add name tun8 type ip6gretap remote \
2401:db00:20:911a:face:0:27:0 local \
2401:db00:20:911a:face:0:25:0 ttl 225 okey 123
Gives MTU of 1430. That is equal to 1500 - 40 - 14 - 4 - 8 - 4.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move l3mdev_rt6_dst_by_oif and l3mdev_get_saddr to l3mdev.c. Collapse
l3mdev_get_rt6_dst into l3mdev_rt6_dst_by_oif since it is the only
user and keep the l3mdev_get_rt6_dst name for consistency with other
hooks.
A follow-on patch adds more code to these functions making them long
for inlined functions.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In netdevice.h we removed the structure in net-next that is being
changes in 'net'. In macsec.c and rtnetlink.c we have overlaps
between fixes in 'net' and the u64 attribute changes in 'net-next'.
The mlx5 conflicts have to do with vxlan support dependencies.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following large patchset contains Netfilter updates for your
net-next tree. My initial intention was to send you this in two goes but
when I looked back twice I already had this burden on top of me.
Several updates for IPVS from Marco Angaroni:
1) Allow SIP connections originating from real-servers to be load
balanced by the SIP persistence engine as is already implemented
in the other direction.
2) Release connections immediately for One-packet-scheduling (OPS)
in IPVS, instead of making it via timer and rcu callback.
3) Skip deleting conntracks for each one packet in OPS, and don't call
nf_conntrack_alter_reply() since no reply is expected.
4) Enable drop on exhaustion for OPS + SIP persistence.
Miscelaneous conntrack updates from Florian Westphal, including fix for
hash resize:
5) Move conntrack generation counter out of conntrack pernet structure
since this is only used by the init_ns to allow hash resizing.
6) Use get_random_once() from packet path to collect hash random seed
instead of our compound.
7) Don't disable BH from ____nf_conntrack_find() for statistics,
use NF_CT_STAT_INC_ATOMIC() instead.
8) Fix lookup race during conntrack hash resizing.
9) Introduce clash resolution on conntrack insertion for connectionless
protocol.
Then, Florian's netns rework to get rid of per-netns conntrack table,
thus we use one single table for them all. There was consensus on this
change during the NFWS 2015 and, on top of that, it has recently been
pointed as a source of multiple problems from unpriviledged netns:
11) Use a single conntrack hashtable for all namespaces. Include netns
in object comparisons and make it part of the hash calculation.
Adapt early_drop() to consider netns.
12) Use single expectation and NAT hashtable for all namespaces.
13) Use a single slab cache for all namespaces for conntrack objects.
14) Skip full table scanning from nf_ct_iterate_cleanup() if the pernet
conntrack counter tells us the table is empty (ie. equals zero).
Fixes for nf_tables interval set element handling, support to set
conntrack connlabels and allow set names up to 32 bytes.
15) Parse element flags from element deletion path and pass it up to the
backend set implementation.
16) Allow adjacent intervals in the rbtree set type for dynamic interval
updates.
17) Add support to set connlabel from nf_tables, from Florian Westphal.
18) Allow set names up to 32 bytes in nf_tables.
Several x_tables fixes and updates:
19) Fix incorrect use of IS_ERR_VALUE() in x_tables, original patch
from Andrzej Hajda.
And finally, miscelaneous netfilter updates such as:
20) Disable automatic helper assignment by default. Note this proc knob
was introduced by a900689264 ("netfilter: nf_ct_helper: allow to
disable automatic helper assignment") 4 years ago to start moving
towards explicit conntrack helper configuration via iptables CT
target.
21) Get rid of obsolete and inconsistent debugging instrumentation
in x_tables.
22) Remove unnecessary check for null after ip6_route_output().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tables have to exist for VRFs to function. Ensure they exist
when VRF device is created.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Responses for packets to unused ports are getting lost with L3 domains.
IPv4 has ip_send_unicast_reply for sending TCP responses which accounts
for L3 domains; update the IPv6 counterpart tcp_v6_send_response.
For icmp the L3 master check needs to be moved up in icmp6_send
to properly respond to UDP packets to a port with no listener.
Fixes: ca254490c8 ("net: Add VRF support to IPv6 stack")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dprintf() and duprintf() functions are enabled at compile time,
these days we have better runtime debugging through pr_debug() and
static keys.
On top of this, this debugging is so old that I don't expect anyone
using this anymore, so let's get rid of this.
IP_NF_ASSERT() is still left in place, although this needs that
NETFILTER_DEBUG is enabled, I think these assertions provide useful
context information when reading the code.
Note that ARP_NF_ASSERT() has been removed as there is no user of
this.
Kill also DEBUG_ALLOW_ALL and a couple of pr_error() and pr_debug()
spots that are inconsistently placed in the code.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The ipv6 gre implementation was cleaned up to share more code
with the ipv4 version, but it can be enabled even when NET_IPGRE_DEMUX
is disabled, resulting in a link error:
net/built-in.o: In function `gre_rcv':
:(.text+0x17f5d0): undefined reference to `gre_parse_header'
ERROR: "gre_parse_header" [net/ipv6/ip6_gre.ko] undefined!
This adds a Kconfig dependency to prevent that now invalid
configuration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 308edfdf15 ("gre6: Cleanup GREv6 receive path, call common GRE functions")
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's easier for gre_parse_header to return the header length instead of
filing it into a parameter. That way, the callers that don't care about the
header length can just check whether the returned value is lower than zero.
In gre_err, the tunnel header must not be pulled. See commit b7f8fe251e
("gre: do not pull header in ICMP error processing") for details.
This patch reduces the conflict between the mentioned commit and commit
95f5c64c3c ("gre: Move utility functions to common headers").
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv4/ip_gre.c
Minor conflicts between tunnel bug fixes in net and
ipv6 tunnel cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
The handler 'ila_fill_encap_info' adds one attribute: ILA_ATTR_LOCATOR.
Fixes: 65d7ab8de5 ("net: Identifier Locator Addressing module")
CC: Tom Herbert <tom@herbertland.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the sendmsg function of UDP, raw, ICMP and l2tp sockets, we use local
variables like hlimits, tclass, opt and dontfrag and pass them to corresponding
functions like ip6_make_skb, ip6_append_data and xxx_push_pending_frames.
This is not a good practice and makes it hard to add new parameters.
This fix introduces a new struct ipcm6_cookie similar to ipcm_cookie in
ipv4 and include the above mentioned variables. And we only pass the
pointer to this structure to corresponding functions. This makes it easier
to add new parameters in the future and makes the function cleaner.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes in GREv6 transmit path:
- Call gre_checksum, remove gre6_checksum
- Rename ip6gre_xmit2 to __gre6_xmit
- Call gre_build_header utility function
- Call ip6_tnl_xmit common function
- Call ip6_tnl_change_mtu, eliminate ip6gre_tunnel_change_mtu
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few generic changes to generalize tunnels in IPv6:
- Export ip6_tnl_change_mtu so that it can be called by ip6_gre
- Add tun_hlen to ip6_tnl structure.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch renames ip6_tnl_xmit2 to ip6_tnl_xmit and exports it. Other
users like GRE will be able to call this. The original ip6_tnl_xmit
function is renamed to ip6_tnl_start_xmit (this is an ndo_start_xmit
function).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Create gre_rcv function. This calls gre_parse_header and ip6gre_rcv.
- Call ip6_tnl_rcv. Doing this and using gre_parse_header eliminates
most of the code in ip6gre_rcv.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some basic changes to make IPv6 tunnel receive path look more like
IPv4 path:
- Make ip6_tnl_rcv non-static so that GREv6 and others can call it
- Make ip6_tnl_rcv look like ip_tunnel_rcv
- Switch to gro_cells_receive
- Make ip6_tnl_rcv non-static and export it
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP uses the generic socket backlog code, and this will soon
be changed to not disable BH when protocol is called back.
We need to use appropriate SNMP accessors.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to to make TCP stack preemptible, as draining prequeue
and backlog queues can take lot of time.
Many SNMP updates were assuming that BH (and preemption) was disabled.
Need to convert some __NET_INC_STATS() calls to NET_INC_STATS()
and some __TCP_INC_STATS() to TCP_INC_STATS()
Before using this_cpu_ptr(net->ipv4.tcp_sk) in tcp_v4_send_reset()
and tcp_v4_send_ack(), we add an explicit preempt disabled section.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a forward-port of the original patch from Andrzej Hajda,
he said:
"IS_ERR_VALUE should be used only with unsigned long type.
Otherwise it can work incorrectly. To achieve this function
xt_percpu_counter_alloc is modified to return unsigned long,
and its result is assigned to temporary variable to perform
error checking, before assigning to .pcnt field.
The patch follows conclusion from discussion on LKML [1][2].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2120927
[2]: http://permalink.gmane.org/gmane.linux.kernel/2150581"
Original patch from Andrzej is here:
http://patchwork.ozlabs.org/patch/582970/
This patch has clashed with input validation fixes for x_tables.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Rename IP6_UPD_PO_STATS_BH() to __IP6_UPD_PO_STATS()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename IP6_INC_STATS_BH() to __IP6_INC_STATS()
and IP6_ADD_STATS_BH() to __IP6_ADD_STATS()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename NET_INC_STATS_BH() to __NET_INC_STATS()
and NET_ADD_STATS_BH() to __NET_ADD_STATS()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename ICMP6_INC_STATS_BH() to __ICMP6_INC_STATS()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename UDP_INC_STATS_BH() to __UDP_INC_STATS(),
and UDP6_INC_STATS_BH() to __UDP6_INC_STATS()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the old days (before linux-3.0), SNMP counters were duplicated,
one for user context, and one for BH context.
After commit 8f0ea0fe3a ("snmp: reduce percpu needs by 50%")
we have a single copy, and what really matters is preemption being
enabled or disabled, since we use this_cpu_inc() or __this_cpu_inc()
respectively.
We therefore kill SNMP_INC_STATS_USER(), SNMP_ADD_STATS_USER(),
NET_INC_STATS_USER(), NET_ADD_STATS_USER(), SCTP_INC_STATS_USER(),
SNMP_INC_STATS64_USER(), SNMP_ADD_STATS64_USER(), TCP_ADD_STATS_USER(),
UDP_INC_STATS_USER(), UDP6_INC_STATS_USER(), and XFRM_INC_STATS_USER()
Following patches will rename __BH helpers to make clear their
usage is not tied to BH being disabled.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in the conflicts.
In the macsec case, the change of the default ID macro
name overlapped with the 64-bit netlink attribute alignment
fixes in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to 3bfd847203 ("net: Use passed in table for nexthop lookups")
for IPv4, if the route spec contains a table id use that to lookup the
next hop first and fall back to a full lookup if it fails (per the fix
4c9bcd1179 ("net: Fix nexthop lookups")).
Example:
root@kenny:~# ip -6 ro ls table red
local 2100:1::1 dev lo proto none metric 0 pref medium
2100:1::/120 dev eth1 proto kernel metric 256 pref medium
local 2100:2::1 dev lo proto none metric 0 pref medium
2100:2::/120 dev eth2 proto kernel metric 256 pref medium
local fe80::e0:f9ff:fe09:3cac dev lo proto none metric 0 pref medium
local fe80::e0:f9ff:fe1c:b974 dev lo proto none metric 0 pref medium
fe80::/64 dev eth1 proto kernel metric 256 pref medium
fe80::/64 dev eth2 proto kernel metric 256 pref medium
ff00::/8 dev red metric 256 pref medium
ff00::/8 dev eth1 metric 256 pref medium
ff00::/8 dev eth2 metric 256 pref medium
unreachable default dev lo metric 240 error -113 pref medium
root@kenny:~# ip -6 ro add table red 2100:3::/64 via 2100:1::64
RTNETLINK answers: No route to host
Route add fails even though 2100:1::64 is a reachable next hop:
root@kenny:~# ping6 -I red 2100:1::64
ping6: Warning: source address might be selected on device other than red.
PING 2100:1::64(2100:1::64) from 2100:1::1 red: 56 data bytes
64 bytes from 2100:1::64: icmp_seq=1 ttl=64 time=1.33 ms
With this patch:
root@kenny:~# ip -6 ro add table red 2100:3::/64 via 2100:1::64
root@kenny:~# ip -6 ro ls table red
local 2100:1::1 dev lo proto none metric 0 pref medium
2100:1::/120 dev eth1 proto kernel metric 256 pref medium
local 2100:2::1 dev lo proto none metric 0 pref medium
2100:2::/120 dev eth2 proto kernel metric 256 pref medium
2100:3::/64 via 2100:1::64 dev eth1 metric 1024 pref medium
local fe80::e0:f9ff:fe09:3cac dev lo proto none metric 0 pref medium
local fe80::e0:f9ff:fe1c:b974 dev lo proto none metric 0 pref medium
fe80::/64 dev eth1 proto kernel metric 256 pref medium
fe80::/64 dev eth2 proto kernel metric 256 pref medium
ff00::/8 dev red metric 256 pref medium
ff00::/8 dev eth1 metric 256 pref medium
ff00::/8 dev eth2 metric 256 pref medium
unreachable default dev lo metric 240 error -113 pref medium
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was a simple idea -- save IPv6 configured addresses on a link down
so that IPv6 behaves similar to IPv4. As always the devil is in the
details and the IPv6 stack as too many behavioral differences from IPv4
making the simple idea more complicated than it needs to be.
The current implementation for keeping IPv6 addresses can panic or spit
out a warning in one of many paths:
1. IPv6 route gets an IPv4 route as its 'next' which causes a panic in
rt6_fill_node while handling a route dump request.
2. rt->dst.obsolete is set to DST_OBSOLETE_DEAD hitting the WARN_ON in
fib6_del
3. Panic in fib6_purge_rt because rt6i_ref count is not 1.
The root cause of all these is references related to the host route for
an address that is retained.
So, this patch deletes the host route every time the ifdown loop runs.
Since the host route is deleted and will be re-generated an up there is
no longer a need for the l3mdev fix up. On the 'admin up' side move
addrconf_permanent_addr into the NETDEV_UP event handling so that it
runs only once versus on UP and CHANGE events.
All of the current panics and warnings appear to be related to
addresses on the loopback device, but given the catastrophic nature when
a bug is triggered this patch takes the conservative approach and evicts
all host routes rather than trying to determine when it can be re-used
and when it can not. That can be a later optimizaton if desired.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 841645b5f2.
Ok, this puts the feature back. I've decided to apply David A.'s
bug fix and run with that rather than make everyone wait another
whole release for this feature.
Signed-off-by: David S. Miller <davem@davemloft.net>
Support checksum neutral ILA as described in the ILA draft. The low
order 16 bits of the identifier are used to contain the checksum
adjustment value.
The csum-mode parameter is added to described checksum processing. There
are three values:
- adjust transport checksum (previous behavior)
- do checksum neutral mapping
- do nothing
On output the csum-mode in the ila_params is checked and acted on. If
mode is checksum neutral mapping then to mapping and set C-bit.
On input, C-bit is checked. If it is set checksum-netural mapping is
done (regardless of csum-mode in ila params) and C-bit will be cleared.
If it is not set then action in csum-mode is taken.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change model of xlat to be used only for input where lookup is done on
the locator part of an address (comparing to locator_match as key
in rhashtable). This is needed for checksum neutral translation
which obfuscates the low order 16 bits of the identifier. It also
permits hosts to be in muliple ILA domains (each locator can map
to a different SIR address). A check is also added to disallow
translating non-ILA addresses (check of type in identifier).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add structures for identifiers, locators, and an ila address which
is composed of a locator and identifier and in6_addr can be cast to
it. This includes a three bit type field and enums for the types defined
in ILA I-D.
In ILA lwt don't allow user to set a translation for a non-ILA
address (type of identifier is zero meaning it is an IID). This also
requires that the destination prefix is at least 65 bytes (64
bit locator and first byte of identifier).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should call consume_skb(skb) when skb is properly consumed,
or kfree_skb(skb) when skb must be dropped in error case.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts the following three commits:
70af921db6799977d9aaf1705ec197
The feature was ill conceived, has terrible semantics, and has added
nothing but regressions to the already fragile ipv6 stack.
Fixes: f1705ec197 ("net: ipv6: Make address flushing on ifdown optional")
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_route_output() will never return a NULL pointer, so there's no need
to check it.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree, mostly from Florian Westphal to sort out the lack of sufficient
validation in x_tables and connlabel preparation patches to add
nf_tables support. They are:
1) Ensure we don't go over the ruleset blob boundaries in
mark_source_chains().
2) Validate that target jumps land on an existing xt_entry. This extra
sanitization comes with a performance penalty when loading the ruleset.
3) Introduce xt_check_entry_offsets() and use it from {arp,ip,ip6}tables.
4) Get rid of the smallish check_entry() functions in {arp,ip,ip6}tables.
5) Make sure the minimal possible target size in x_tables.
6) Similar to #3, add xt_compat_check_entry_offsets() for compat code.
7) Check that standard target size is valid.
8) More sanitization to ensure that the target_offset field is correct.
9) Add xt_check_entry_match() to validate that matches are well-formed.
10-12) Three patch to reduce the number of parameters in
translate_compat_table() for {arp,ip,ip6}tables by using a container
structure.
13) No need to return value from xt_compat_match_from_user(), so make
it void.
14) Consolidate translate_table() so it can be used by compat code too.
15) Remove obsolete check for compat code, so we keep consistent with
what was already removed in the native layout code (back in 2007).
16) Get rid of target jump validation from mark_source_chains(),
obsoleted by #2.
17) Introduce xt_copy_counters_from_user() to consolidate counter
copying, and use it from {arp,ip,ip6}tables.
18,22) Get rid of unnecessary explicit inlining in ctnetlink for dump
functions.
19) Move nf_connlabel_match() to xt_connlabel.
20) Skip event notification if connlabel did not change.
21) Update of nf_connlabels_get() to make the upcoming nft connlabel
support easier.
23) Remove spinlock to read protocol state field in conntrack.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts were two cases of simple overlapping changes,
nothing serious.
In the UDP case, we need to add a hlist_add_tail_rcu()
to linux/rculist.h, because we've moved UDP socket handling
away from using nulls lists.
Signed-off-by: David S. Miller <davem@davemloft.net>
Separated from previous patch for readability.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Struct ctl_table_header holds pointer to sysctl table which could be used
for freeing it after unregistration. IPv4 sysctls already use that.
Remove redundant NULL assignment: ndev allocated using kzalloc.
This also saves some bytes: sysctl table could be shorter than
DEVCONF_MAX+1 if some options are disable in config.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code borrowed from bits and pieces of other protocols to
the IPv6 GRE path so that we can support GSO over IPv6 based GRE tunnels.
By adding this support we are able to significantly improve the throughput
for GRE tunnels as we are able to make use of GSO.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the basic offloads we support on most devices.
Specifically with this patch set we can support checksum offload, basic
scatter-gather, and highdma.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we were creating an ip6gretap interface the MTU was about 6 bytes
short of what was needed. It turns out we were not taking the Ethernet
header into account and as a result we were eating into the 8 bytes
reserved for the encap limit.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern