This patch removes the use of the TG3_FLAG_5701_REG_WRITE_BUG flag.
It's logic is only used to set a function pointer and thus the
logic can be collapsed and the flag removed.
[ Comment tidy by Christoph Hellwig. -DaveM ]
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
The reset was added a while back so that ASF could re-init whatever
MAC address it wanted to use after the MAC address was changed.
Instead of resetting, we can just keep MAC address 1 unchanged during
MAC address changes if MAC address 1 is different from MAC address 0.
This fixes 2 problems:
1. Bonding calls set_mac_address in contexts that cannot sleep.
It no longer sleeps with the chip reset removed.
2. When ASF shares the same MAC address as the NIC, it needs to
always do that even when the MAC address is changed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change TG3_FLAG_SERDES_WOL_CAP to TG3_FLAG_WOL_CAP to make it easier
to manage WoL. This flag is now used consistently during ethtool WoL
setup and power setting changes.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPIO settings may change during reset and so the stored values in
tp->grc_local_ctrl should be cleared first.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the NVRAM sizing procedure so that the driver can
take advantage of devices with 1:1 NVRAM strapping configurations. This
is useful in cases where the traditional NVRAM sizing method fails. In
the event that the flash size cannot be determined, the largest known
NVRAM size is used. The patch also removes support for 5755 NVRAM
devices that are not supported by Broadcom and adds explicit sizing for
this device.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Remove the check for skb->len greater than MTU when doing TSO.
When the destination has a smaller MSS than the source, a TSO packet
may be smaller than the MTU and we still need to process it as a TSO
packet.
2. On 5705A3 devices with TSO enabled, the DMA engine can hang due to a
hardware bug. This patch avoids the hanging condition by reducing the
DMA burst size.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6: (67 commits)
[SCSI] SUNESP: Complete driver rewrite to version 2.0
[SPARC64]: Convert PCI over to generic struct iommu/strbuf.
[SPARC]: device_node name constification fallout
[SPARC64]: Convert SBUS over to generic iommu/strbuf structs.
[SPARC64]: Add generic iommu and strbuf structs to iommu.h
[SPARC64]: Consolidate {sbus,pci}_iommu_arena.
[SPARC]: Make device_node name and type const
[SPARC64]: constify some paramaters of OF routines
[TIGON3]: of_get_property() returns const.
[SPARC64]: Fix PCI rework to adhere to of_get_property() const return.
[SPARC64]: Document and fix calculation of pages_avail.
[SPARC64]: Make sure pbm->prom_node is setup easly enough in psycho.c
[SPARC64]: Use bootmem_bootmap_pages() in choose_bootmap_pfn().
[SPARC64]: Add proper header file extern for cmdline_memory_size.
[SPARC64]: Kill sparc_ultra_dump_{i,d}tlb()
[SPARC64]: Use DECLARE_BITMAP and BITS_TO_LONGS in mm/init.c
[SPARC64]: Give move verbose show_mem() output just like i386.
[SPARC64]: Mark show_mem() printk's with KERN_INFO.
[SPARC64]: Kill kvaddr_to_phys() and friends.
[SPARC64]: Privatize sun4u_get_pte() and fix name.
...
The only unfortunate bit here is that the name field of struct map_info
is not const, so for now we put a cast on the assignment of it.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
To clearly state the intent of copying from linear sk_buffs, _offset being a
overly long variant but interesting for the sake of saving some bytes.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The ip_hdrlen() buddy, created to reduce the number of skb->h.th-> uses and to
avoid the longer, open coded equivalent.
Ditched a no-op in bnx2 in the process.
I wonder if we should have a BUG_ON(skb->h.th->doff < 5) in tcp_optlen()...
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common sequence "skb->nh.iph->ihl * 4", removing a good number of open
coded skb->nh.iph uses, now to go after the rest...
Just out of curiosity, here are the idioms found to get the same result:
skb->nh.iph->ihl << 2
skb->nh.iph->ihl<<2
skb->nh.iph->ihl * 4
skb->nh.iph->ihl*4
(skb->nh.iph)->ihl * sizeof(u32)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver will crash when the chip has been initialized by EFI before
tg3_init_one(). In this case, the driver will call tg3_chip_reset()
before allocating consistent memory.
The bug is fixed by checking for tp->hw_status before accessing it
during tg3_chip_reset().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On most tg3 chips, the memory enable bit in the PCI command register
gets cleared during chip reset and must be restored before accessing
PCI registers using memory cycles. The chip does not generate
interrupt during chip reset, but the irq handler can still be called
because of irq sharing or irqpoll. Reading a register in the irq
handler can cause a master abort in this scenario and may result in a
crash on some architectures.
Use the TG3_FLAG_CHIP_RESETTING flag to tell the irq handler to exit
without touching any registers. The checking of the flag is in the
"slow" path of the irq handler and will not affect normal performance.
The msi handler is not shared and therefore does not require checking
the flag.
Thanks to Bernhard Walle <bwalle@suse.de> for reporting the problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This flag to support multiple PCIX split completions was never used
because of hardware bugs. This will make room for a new flag.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch splits the vlan_group struct into a multi-allocated struct. On
x86_64, the size of the original struct is a little more than 32KB, causing
a 4-order allocation, which is prune to problems caused by buddy-system
external fragmentation conditions.
I couldn't just use vmalloc() because vfree() cannot be called in the
softirq context of the RCU callback.
Signed-off-by: Dan Aloni <da-x@monatomic.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Add race condition check after netif_stop_queue(). tg3_tx() runs
without netif_tx_lock and can race with tg3_start_xmit_dma_bug() ->
tg3_tso_bug().
2. Firmware TSO in 5703/5704/5705 also have the same TSO limitation,
i.e. they cannot handle TSO headers bigger than 80 bytes. Rename
TG3_FL2_HW_TSO_1_BUG to TG3_FL2_TSO_BUG and set this flag on
these chips as well.
3. Update version to 3.74.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print the most useful information during tx timeout to help debug.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set DMA read watermark to 4 on 5703 in PCIX mode. This is needed to
prevent some tx timeouts.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the following problem:
http://bugzilla.kernel.org/show_bug.cgi?id=7969
The MSI state needs to be saved during suspend. PCI state saved
during tg3_init_one() does not contain valid MSI state because
MSI hasn't been enabled.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During an oprofile session of linux-2.6.20 on a dual opteron system, I noticed
an expensive divide was done in tg3_poll().
I am using gcc-4.1.1, so the following comment from drivers/net/tg3.c seems
over-optimistic :
/* Do not place this n-ring entries value into the tp struct itself,
* we really want to expose these constants to GCC so that modulo et
* al. operations are done with shifts and masks instead of with
* hw multiply/modulo instructions. Another solution would be to
* replace things like '% foo' with '& (foo - 1)'.
*/
#define TG3_RX_RCB_RING_SIZE(tp) \
((tp->tg3_flags2 & TG3_FLG2_5705_PLUS) ? 512 : 1024)
Assembly code before patch :
(oprofile results included)
6434 0.0088 :ffffffff803684b9: mov 0x6f0(%r15),%eax
587 8.0e-04 :ffffffff803684c0: and $0x40000,%eax
2170 0.0030 :ffffffff803684c5: cmp $0x1,%eax
:ffffffff803684c8: lea 0x1(%r13),%eax
:ffffffff803684cc: sbb %ecx,%ecx
2051 0.0028 :ffffffff803684ce: xor %edx,%edx
:ffffffff803684d0: and $0x200,%ecx
20 2.7e-05 :ffffffff803684d6: add $0x200,%ecx
1986 0.0027 :ffffffff803684dc: div %ecx
103427 0.1410 :ffffffff803684de: cmp %edx,0xffffffffffffff7c(%rbp)
Assembly code after the suggested patch :
ffffffff803684b9: mov 0x6f0(%r15),%eax
ffffffff803684c0: and $0x40000,%eax
ffffffff803684c5: cmp $0x1,%eax
ffffffff803684c8: sbb %eax,%eax
ffffffff803684ca: inc %r13d
ffffffff803684cd: and $0x200,%eax
ffffffff803684d2: add $0x1ff,%eax
ffffffff803684d7: and %eax,%r13d
ffffffff803684da: cmp %r13d,0xffffffffffffff7c(%rbp)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the NETIF_F_TSO #ifdef-ery in drivers/net; this was
for old-old-2.4 compat (even current 2.4 has NETIF_F_TSO)
but it's time to get rid of it by now.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some PHY trim values need to be fine-tuned on 5755M to be
IEEE-compliant.
Update version to 3.72.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5906 PHY requires a special register bit to power down and up the
PHY.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hot-plug scripts can call tg3_open() as soon as register_netdev() is
called in tg3_init_one(). We need to call pci_set_drvdata() before
register_netdev(), and netif_carrier_off() needs to be moved to
tg3_open() to avoid race conditions.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tp->link_config.orig_* values must be assigned during
tg3_set_settings() because these values will be used to setup the
link speed during tg3_open(). Without these assignments, the link
speed settings will be all messed by if tg3_set_settings() is called
when the device is down.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kmalloc+memset with kzalloc
Signed-off-by: Yan Burman <burman.yan@gmail.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the message to more clearly identify Serdes devices.
Update version to 3.70.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change some udelay() in some eeprom functions to msleep(). Eeprom
related functions are always called from sleepable context.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netif_msg_* to turn on or off some messages.
Based on Stephen Hemminger's initial patch.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Honor the advertisement bitmask from ethtool. We used to always
advertise the full capability when autoneg was set to on.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Tg3_FLG2_IS_NIC flag to unambiguously determine whether the
device is NIC or onboard. Previously, the EEPROM_WRITE_PROT flag was
overloaded to also mean onboard. With the separation, we can
support some devices that are onboard but do not use eeprom write
protect.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phy loopback on most 10/100 devices need to be run in 1Gbps mode in
GMII mode.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse noticed a locking imbalance in tg3_open(). This patch adds an
unlock to one of the error paths, so that tg3_open() always exits
without the lock held.
Signed-off-by: Ira W. Snyder <kernel@irasnyder.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to hardware errata, TSO must be disabled if the PCI Express clock
request is enabled on 5906. The chip may hang when transmitting TSO
frames if CLKREQ is enabled.
Update version to 3.69.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer 5906 bootcode needs about 7ms to finish resetting so the poll
firmware loop was changed to maximum 20ms.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use proper upper limits for the loops and check for all error
conditions.
The problem was noticed by Adrian Bunk.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a bug reported in:
http://bugzilla.kernel.org/show_bug.cgi?id=7438
tg3_close() turns off the PHY if WoL and ASF are both disabled. On
the next tg3_open(), some devices such as the 5752M will not be
brought up correctly without a PHY reset early in the reset sequence.
The PHY clock is needed for some internal MAC blocks to function
correctly.
This problem is fixed by always resetting the PHY early in
tg3_reset_hw() when it is called from tg3_open() or tg3_resume().
tg3_setup_phy() can then be called later in the sequence without the
reset_phy parameter set to 1, since the PHY reset is already done.
Update version to 3.68.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The minimum tx ring size must be greater than MAX_SKB_FRAGS or 3
times that on some chips with TSO bugs.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the implementation of the ethtool set ring parameters for the
tg3 transmit ring. The size of tx_pending is taken into account
before doing a netif_wake_queue. This prevents the interface from
locking up when smaller transmit ring sizes are used.
Signed-off-by: Ranjit Manomohan <ranjitm@google.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
Add support for the new 5709 device. This is a new 10/100 Mbps chip.
The mailbox access and firmware interface are quite different from
all other tg3 chips.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put the firmware polling logic into a separate function. This makes
the code cleaner.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHY related fixes:
1. Fix Serdes WoL.
2. Fix loopback test on 10/100 only devices.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change to a different ASF heartbeat message code to improve
reliability.
There were some reports of unintended resets on real time kernels
where the timer may be slow and cause the heartbeat to be late.
Netpoll will also have the same problem because the timer irq will
be unavailable.
Using the new heartbeat code, the ASF firmware will also check the
ring condition before resetting the chip when the heartbeat is
expiring.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve 5704S autoneg logic by using a serdes_counter field to keep
track of the transient states. This eliminates a 200 msec busy
loop in the code. Autoneg will take its course without the driver
busy waiting for it to finish.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (217 commits)
net/ieee80211: fix more crypto-related build breakage
[PATCH] Spidernet: add ethtool -S (show statistics)
[NET] GT96100: Delete bitrotting ethernet driver
[PATCH] mv643xx_eth: restrict to 32-bit PPC_MULTIPLATFORM
[PATCH] Cirrus Logic ep93xx ethernet driver
r8169: the MMIO region of the 8167 stands behin BAR#1
e1000, ixgb: Remove pointless wrappers
[PATCH] Remove powerpc specific parts of 3c509 driver
[PATCH] s2io: Switch to pci_get_device
[PATCH] gt96100: move to pci_get_device API
[PATCH] ehea: bugfix for register access functions
[PATCH] e1000 disable device on PCI error
drivers/net/phy/fixed: #if 0 some incomplete code
drivers/net: const-ify ethtool_ops declarations
[PATCH] ethtool: allow const ethtool_ops
[PATCH] sky2: big endian
[PATCH] sky2: fiber support
[PATCH] sky2: tx pause bug fix
drivers/net: Trim trailing whitespace
[PATCH] ehea: IBM eHEA Ethernet Device Driver
...
Manually resolved conflicts in drivers/net/ixgb/ixgb_main.c and
drivers/net/sky2.c related to CHECKSUM_HW/CHECKSUM_PARTIAL changes by
commit 84fa7933a3 that just happened to be
next to unrelated changes in this update.
Convert the pci_device_ids to PCI_DEVICE() macro. Saves 1.5k in the
sourcefile.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace CHECKSUM_HW by CHECKSUM_PARTIAL (for outgoing packets, whose
checksum still needs to be completed) and CHECKSUM_COMPLETE (for
incoming packets, device supplied full checksum).
Patch originally from Herbert Xu, updated by myself for 2.6.18-rc3.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix a subtle race condition between tg3_start_xmit() and tg3_tx()
discovered by Herbert Xu <herbert@gondor.apana.org.au>:
CPU0 CPU1
tg3_start_xmit()
if (tx_ring_full) {
tx_lock
tg3_tx()
if (!netif_queue_stopped)
netif_stop_queue()
if (!tx_ring_full)
update_tx_ring
netif_wake_queue()
tx_unlock
}
Even though tx_ring is updated before the if statement in tg3_tx() in
program order, it can be re-ordered by the CPU as shown above. This
scenario can cause the tx queue to be stopped forever if tg3_tx() has
just freed up the entire tx_ring. The possibility of this happening
should be very rare though.
The following changes are made:
1. Add memory barrier to fix the above race condition.
2. Eliminate the private tx_lock altogether and rely solely on
netif_tx_lock. This eliminates one spinlock in tg3_start_xmit()
when the ring is full.
3. Because of 2, use netif_tx_lock in tg3_tx() before calling
netif_wake_queue().
4. Change TX_BUFFS_AVAIL to an inline function with a memory barrier.
Herbert and David suggested using the memory barrier instead of
volatile.
5. Check for the full wake queue condition before getting
netif_tx_lock in tg3_tx(). This reduces the number of unnecessary
spinlocks when the tx ring is full in a steady-state condition.
6. Update version to 3.65.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
All caller of netdev_alloc_skb need to assign skb->dev shortly
afterwards. Move it into common code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle dev_alloc_skb() failures when initializing the RX rings.
Without proper handling, the driver will crash when using a partial
ring.
Thanks to Stephane Doyon <sdoyon@max-t.com> for reporting the bug and
providing the initial patch.
Howie Xu <howie@vmware.com> also reported the same issue.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tg3_restart_hw() to handle failures when re-initializing the
device.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the AMD 8131 bridge to the list of chipsets that reorder writes.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable ipv6 TSO feature on chips that support it.
Update version to 3.61.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[IPV6]: Added GSO support for TCPv6
[NET]: Generalise TSO-specific bits from skb_setup_caps
[IPV6]: Added GSO support for TCPv6
[IPV6]: Remove redundant length check on input
[NETFILTER]: SCTP conntrack: fix crash triggered by packet without chunks
[TG3]: Update version and reldate
[TG3]: Add TSO workaround using GSO
[TG3]: Turn on hw fix for ASF problems
[TG3]: Add rx BD workaround
[TG3]: Add tg3_netif_stop() in vlan functions
[TCP]: Reset gso_segs if packet is dodgy
Use GSO to workaround a rare TSO bug on some chips. This hardware
bug may be triggered when the TSO header size is greater than 80
bytes. When this condition is detected in a TSO packet, the driver
will use GSO to segment the packet to workaround the hardware bug.
Thanks to Juergen Kreileder <jk@blackdown.de> for reporting the
problem and collecting traces to help debug the problem.
And thanks to Herbert Xu <herbert@gondor.apana.org.au> for providing
the GSO mechanism that happens to be the perfect workaround for this
problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear a bit to enable a hardware fix for some ASF related problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add workaround to limit the burst size of rx BDs being DMA'ed to the
chip. This works around hardware errata on a number of 5750, 5752,
and 5755 chips.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tg3_netif_stop() when changing the vlgrp (vlan group) pointer. It
is necessary to quiesce the device before changing that pointer.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One thing this change pointed out was that we really should
pull the "get 'local-mac-address' property" logic into a helper
function all the network drivers can call.
Signed-off-by: David S. Miller <davem@davemloft.net>
Having separate fields in sk_buff for TSO/UFO (tso_size/ufo_size) is not
going to scale if we add any more segmentation methods (e.g., DCCP). So
let's merge them.
They were used to tell the protocol of a packet. This function has been
subsumed by the new gso_type field. This is essentially a set of netdev
feature bits (shifted by 16 bits) that are required to process a specific
skb. As such it's easy to tell whether a given device can process a GSO
skb: you just have to and the gso_type field and the netdev's features
field.
I've made gso_type a conjunction. The idea is that you have a base type
(e.g., SKB_GSO_TCPV4) that can be modified further to support new features.
For example, if we add a hardware TSO type that supports ECN, they would
declare NETIF_F_TSO | NETIF_F_TSO_ECN. All TSO packets with CWR set would
have a gso_type of SKB_GSO_TCPV4 | SKB_GSO_TCPV4_ECN while all other TSO
packets would be SKB_GSO_TCPV4. This means that only the CWR packets need
to be emulated in software.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu pointed out that it is unsafe to call netif_tx_disable()
from LLTX drivers because it uses dev->xmit_lock to synchronize
whereas LLTX drivers use private locks.
Convert tg3 to non-LLTX to fix this issue. tg3 is a lockless driver
where hard_start_xmit and tx completion handling can run concurrently
under normal conditions. A tx_lock is only needed to prevent
netif_stop_queue and netif_wake_queue race condtions when the queue
is full.
So whether we use LLTX or non-LLTX, it makes practically no
difference.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove tx_lock where it is unnecessary. tg3 runs lockless and so it
requires interrupts to be disabled and sync'ed, netif_queue and NAPI
poll to be stopped before the device can be reconfigured. After
stopping everything, it is no longer necessary to get the tx_lock.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add recovery logic when we suspect that the system is re-ordering
MMIOs. Re-ordered MMIOs to the send mailbox can cause bogus tx
completions and hit BUG_ON() in the tx completion path.
tg3 already has logic to handle re-ordered MMIOs by flushing the MMIOs
that must be strictly ordered (such as the send mailbox). Determining
when to enable the flush is currently a manual process of adding known
chipsets to a list.
The new code replaces the BUG_ON() in the tx completion path with the
call to tg3_tx_recover(). It will set the TG3_FLAG_MBOX_WRITE_REORDER
flag and reset the chip later in the workqueue to recover and start
flushing MMIOs to the mailbox.
A message to report the problem will be printed. We will then decide
whether or not to add the host bridge to the list of chipsets that do
re-ordering.
We may add some additional code later to print the host bridge's ID so
that the user can report it more easily.
The assumption that re-ordering can only happen on x86 systems is also
removed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PCI ID for BCM5786 which is a variant of 5787.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of all the SUN_570X logic and instead:
1) Make sure MEMARB_ENABLE is set when we probe the SRAM
for config information. If that is off we will get
timeouts.
2) Always try to sync with the firmware, if there is no
firmware running do not treat it as an error and instead
just report it the first time we notice this condition.
3) If there is no valid SRAM signature, assume the device
is onboard by setting TG3_FLAG_EEPROM_WRITE_PROT.
Update driver version and release date.
With help from Michael Chan and Fabio Massimo Di Nitto.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some missing rx error counters for 5705 and newer chips.
Update version to 3.58.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even with fiber cards ethtool reports that the connected port is TP,
the patch fix this.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3_run_loopback doesn't check that dev_alloc_skb() returns anything
useful.
Even if dev_alloc_skb() fails to return an skb to us we'll happily go
on and assume it did, so we risk dereferencing a NULL pointer. Much
better to fail gracefully by returning -ENOMEM than crashing here.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix bug in nvram write function. If the starting nvram address offset
happens to be the last dword of the page, the NVRAM_CMD_LAST bit will
not get set in the existing code. This patch fixes the bug by changing
the "else if" to "if" so that the last dword condition always gets
checked.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a reset_phy parameter to tg3_reset_hw() and tg3_init_hw(). With
the full chip reset during MAC address change, the automatic PHY reset
during chip reset will cause a link down and bonding will not work
properly as a result. With this reset_phy parameter, we can do a chip
reset without link down when changing MAC address or MTU.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do the full chip reset when changing MAC address if ASF is enabled.
ASF sometimes uses a different MAC address than the driver. Without
the reset, the ASF MAC address may be overwritten when the driver's
MAC address is changed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some PHY workaround code to reduce jitter on some PHYs.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netif_carrier_off() call during tg3_phy_reset(). This is needed
to properly track the netif_carrier state in cases where we do a
PHY reset with interrupts disabled. The SerDes code will not run
properly if the netif_carrier state is wrong.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Speed up SRAM read and write functions if possible by using MMIO
instead of config. cycles. With this change, the post reset signature
done at the end of D3 power change must now be moved before the D3
power change.
IBM reported a problem on powerpc blades during ethtool self test that
was caused by the memory test taking excessively long. Config. cycles
are very slow on powerpc and the memory test can take more than 10
seconds to complete using config. cycles.
David Miller informed me that an earlier version of the patch caused
problems on sparc64 systems with built-in tg3 chips. This version
fixes the problem by excluding all SUN built-in tg3 chips from doing
MMIO SRAM access.
TG3_FLAG_EEPROM_WRITE_PROT is also set unconditionally when
TG3_FLG2_SUN_570X is set. This should be sane as all SUN chips are
built-in and do not require Vaux switching.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kill the TG3_FLAG_NO_{TX|RX}_PSEUDO_CSUM flags because they are not
very useful. This will free up some bits for new flags.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a memory leak (buf wasn't freed) spotted by the
Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (48 commits)
Documentation: fix minor kernel-doc warnings
BUG_ON() Conversion in drivers/net/
BUG_ON() Conversion in drivers/s390/net/lcs.c
BUG_ON() Conversion in mm/slab.c
BUG_ON() Conversion in mm/highmem.c
BUG_ON() Conversion in kernel/signal.c
BUG_ON() Conversion in kernel/signal.c
BUG_ON() Conversion in kernel/ptrace.c
BUG_ON() Conversion in ipc/shm.c
BUG_ON() Conversion in fs/freevxfs/
BUG_ON() Conversion in fs/udf/
BUG_ON() Conversion in fs/sysv/
BUG_ON() Conversion in fs/inode.c
BUG_ON() Conversion in fs/fcntl.c
BUG_ON() Conversion in fs/dquot.c
BUG_ON() Conversion in md/raid10.c
BUG_ON() Conversion in md/raid6main.c
BUG_ON() Conversion in md/raid5.c
Fix minor documentation typo
BFP->BPF in Documentation/networking/tuntap.txt
...
this changes if() BUG(); constructs to BUG_ON() which is
cleaner, contains unlikely() and can better optimized away.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Undo commit 100c467330
MMIOs timeout more quickly that PCI config cycles and some
of these SRAM accesses can take a very long time, triggering
the MMIO limits on some sparc64 PCI controllers and thus
resulting in bus timeouts and bus errors.
Signed-off-by: David S. Miller <davem@davemloft.net>
Skip the main timer code if interrupts are disabled in the full lock
state.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Speed up SRAM read and write functions if possible by using MMIO
instead of config. cycles. With this change, the post reset signature
done at the end of D3 power change must now be moved before the D3
power change.
IBM reported a problem on powerpc blades during ethtool self test
that was caused by the memory test taking excessively long. Config.
cycles are very slow on powerpc and the memory test can take more
than 10 seconds to complete using config. cycles. As a result, NETDEV
WATCHDOG can be triggered during self test and the chip can end up in
a funny state.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to check the TG3_FLAG_40BIT_DMA_BUG flag in the workaround code
path instead of device flags.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some older bootcode in some devices may report 0 MAC address in
SRAM when booting up from low power state. This patch fixes the
problem by checking for a valid MAC address in SRAM and falling back
to NVRAM if necessary.
Thanks to walt <wa1ter@myrealbox.com> for reporting the problem
and helping to debug it.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for new chip 5755 which is very similar to 5787.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHYs should not be powered down in tg3_set_power_state() because
of bugs or other hardware limitations.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
5700 and 5701 will not return correct SRAM data when the chip is in
D3hot power state. tg3_get_eeprom_hw_cfg() must first put the device
in D0 before reading SRAM.
Thanks to Thomas Chenault at Dell for noticing this problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the needlessly global function tg3_request_irq()
static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the netif_carrier_off() call from tg3_init_one()->
tg3_init_link_config() to tg3_open() as is the convention for most other
network drivers.
I was getting a panic after a tg3 device failed to initialize due to DMA
failure. The oops pointed to the link watch queue with spinlock debugging
enabled. Without spinlock debugging, the Oops didn't occur.
I suspect that the link event was getting queued but not executed until
after the DMA test had failed and the device was freed. The link event was
then operating on freed memory, which could contain anything. With this
patch applied, the Oops no longer occurs.
[ Based upon feedback from Michael Chan, we move netif_carrier_off()
to the end of tg3_init_one() instead of moving it to tg3_open() -DaveM ]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some nvram related cleanup:
1. Add a tg3_nvram_read_swab() since swabing the data is frequently
done.
2. Add a function to convert nvram address to physical address
instead of doing it in 2 separate places.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool memory test on 5787 requires a new memory table.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support one-shot MSI on 5787.
This one-shot MSI idea is credited to David Miller. In this mode, MSI
disables itself automatically after it is generated, saving the driver
a register access to disable it for NAPI.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support ipv6 tx csum on 5787 by setting NETIF_F_HW_CSUM.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support 5787 hardware TSO using a new flag TG3_FLG2_HW_TSO_2.
Since the TSO interface is slightly different and these chips have
finally fixed the 4GB DMA problem and do not have the 40-bit DMA
problem, a new hard_start_xmit is used for these chips. All previous
chips will use the old hard_start_xmit that is now renamed
tg3_start_xmit_dma_bug().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support additional nvrams and new nvram format for 5787 and 5754.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix-up tg3_get_ringparam() to return the correct parameters.
Set the jumbo rx ring parameter only if it is supported by the chip
and currently in use.
Add missing value for tx_max_pending, noticed by Rick Jones.
Update version to 3.51.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing netif_running() checks in tg3's dev->set_multicast_list()
and dev->set_mac_address(). If not netif_running(), these 2 calls can
simply return 0 after storing the new settings if required.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support WoL during shutdown by calling
tg3_set_power_state(tp, PCI_D3hot) during tg3_close().
Change the power state parameter to pci_power_t type and use
constants defined in pci.h.
Certain ethtool operations cannot be performed after tg3_close()
because the device will go to low power state. Add return -EAGAIN
in such cases where appropriate.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable TSO by default on newer chips that support TSO in hardware.
Leave TSO off by default on older chips that do firmware TSO because
performance is slightly lower.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6: (230 commits)
[SPARC64]: Update defconfig.
[SPARC64]: Fix 2 bugs in huge page support.
[SPARC64]: CONFIG_BLK_DEV_RAM fix
[SPARC64]: Optimized TSB table initialization.
[SPARC64]: Allow CONFIG_MEMORY_HOTPLUG to build.
[SPARC64]: Use SLAB caches for TSB tables.
[SPARC64]: Don't kill the page allocator when growing a TSB.
[SPARC64]: Randomize mm->mmap_base when PF_RANDOMIZE is set.
[SPARC64]: Increase top of 32-bit process stack.
[SPARC64]: Top-down address space allocation for 32-bit tasks.
[SPARC64] bbc_i2c: Fix cpu check and add missing module license.
[SPARC64]: Fix and re-enable dynamic TSB sizing.
[SUNSU]: Fix missing spinlock initialization.
[TG3]: Do not try to access NIC_SRAM_DATA_SIG on Sun parts.
[SPARC64]: First cut at VIS simulator for Niagara.
[SPARC64]: Fix system type in /proc/cpuinfo and remove bogus OBP check.
[SPARC64]: Add SMT scheduling support for Niagara.
[SPARC64]: Fix 32-bit truncation which broke sparsemem.
[SPARC64]: Move over to sparsemem.
[SPARC64]: Fix new context version SMP handling.
...
Sun does't put an SEEPROM behind the tigon3 chip, among other things,
so accesses to these areas just give bus timeouts.
Signed-off-by: David S. Miller <davem@davemloft.net>
The 40-bit DMA workaround recently implemented for 5714, 5715, and
5780 needs to be expanded because there may be other tg3 devices
behind the EPB Express to PCIX bridge in the 5780 class device.
For example, some 4-port card or mother board designs have 5704 behind
the 5714.
All devices behind the EPB require the 40-bit DMA workaround.
Thanks to Chris Elmquist again for reporting the problem and testing
the patch.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Coverity checker spotted this dead code (note that (clock_ctrl == 7)
is already handled above).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add DMA workaround for chips that do not support full 64-bit DMA
addresses.
5714, 5715, and 5780 chips only support DMA addresses less than 40
bits. On 64-bit systems with IOMMU, set the dma_mask to 40-bit so
that pci_map_xxx() calls will map the DMA address below 40 bits if
necessary. On 64-bit systems without IOMMU, set the dma_mask to
64-bit and check for DMA addresses exceeding the limit in
tg3_start_xmit().
5788 only supports 32-bit DMA so need to set the mask appropriately
also.
Thanks to Chris Elmquist at SGI for reporting and helping to debug
the problem on 5714.
Thanks to David Miller for explaining the HIGHMEM and DMA stuff.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Sun parts don't have PCI_VENDOR_ID_SUN in the subsystem
vendor ID. So add another fallback test, which is the name
of the OBP firmware device tree node. If it's a Sun part we'll
get "network", else it will be named "ethernet".
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure tg3_reset_task() is flushed in the close and suspend paths
as noted by Jeff Garzik.
In the close path, calling flush_scheduled_work() may cause deadlock
if linkwatch_event() is on the workqueue. linkwatch_event() will try
to get the rtnl_lock() which is already held by tg3_close(). So
instead, we set a flag in tg3_reset_task() and tg3_close() polls
the flag until it is cleared.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add nvram lock count so that calls to tg3_nvram_lock()/unlock() can
be nested. Add error checking to all callers of tg3_nvram_lock()
where appropriate. To prevent nvram lock failures after halting the
firmware, it is also necessary to release firmware's nvram lock in
tg3_halt_cpu().
Update version to 3.48.
Based on David Miller's initial patch.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turning struct iphdr::tot_len into __be16 added sparse warning.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To help in reducing the number of include dependencies, several files were
touched as they were getting needed headers indirectly for stuff they use.
Thanks also to Alan Menegotto for pointing out that net/dccp/proto.c had
linux/dccp.h include twice.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resubmitting after recommendation to use GET_REG32_1() instead of
GET_REG32_LOOP(..., 1). Retested. Problem remains fixed.
Prevent tg3_get_regs() from reading reserved and undocumented registers
at RX_CPU_BASE and TX_CPU_BASE offsets which caused hostile behavior
on PCIe platforms.
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Skip the memory 0xb50 to 0x1000 during "ethtool -t" memory test.
Overwriting memory in this region can cause ASF problems.
Update version and release date.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tw32_f() function (register write with immediate read flush) can
hang when used on some registers to switch clock frequencies and
power. A new tw32_wait_f() is added for such registers with the
delay before the read and after the read.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some missing workarounds in tg3_set_power_state():
1. Workaround to prevent overdrawing current on 5714.
2. Do not power down 5700's PHY because of hw limitation.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Locate the pdev_peer for dual port 5714 NIC devices in addition to
5704 devices. The name is also changed to tg3_find_peer() from
tg3_find_5704_peer(). It is also necessary to call netdev_priv() to
get to the peer's private tg3 structure.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following bugs in tg3_set_power_state():
1. Both WOL and ASF flags require switching to aux power.
2. Add a missing handshake with firmware to enable WOL.
3. Turn off the PHY if both WOL and ASF are disabled.
4. Add nvram arbitration before halting the firmware.
5. Fix tg3_setup_copper_phy() to switch to 100Mbps when
changing to low power state.
Update revision and date.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the dual-port 5704 is configured as a single-port device with
only one PCI function, it would trigger a BUG() condition in
tg3_find_5704_peer(). This fixes the problem by returning its
own pdev if the peer cannot be found.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix tg3_suspend() and tg3_resume() by clearing and setting the
TG3_FLAG_INIT_COMPLETE flag when appropriate. tg3_set_power_state()
looks at TG3_FLAG_INIT_COMPLETE on the peer device to determine
when to appropriately switch to aux power.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nvram arbitration rules were not strictly followed in a few places
and this could lead to reading corrupted values from the nvram.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ Move assosciated code comment to the correct spot, and
update driver version and release date -DaveM ]
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This one from my DMA_{32,64}BIT_MASK series did not seem to make it
through to upstream.
Use the DMA_{32,64}BIT_MASK constants from dma-mapping.h when calling
pci_set_dma_mask() or pci_set_consistent_dma_mask()
This patch includes dma-mapping.h explicitly because it caused errors
on some architectures otherwise.
See http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Update version and reldate and add more sanity checking to
tg3_set_settings().
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Change the ASF heart beat to 5 seconds for faster detection of system
crash. The driver sends the heartbeat every 2 seconds and the ASF
firmware will timeout and reset the device if no heartbeat is received
after 5 seconds. The old scheme of 2 minutes is ineffective.
tg3_write_mem_fast() is added to speed up the IO to send the heartbeat.
When no workaround is needed, it will use direct MMIO to memory space
to write to memory.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add complete support for 5714/5715. These chips are very similar to
5780 so the changes are very trivial. A TG3_FLG2_5780_CLASS flag is
added to identify these chips.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Test for VIA K8T800 north bridge instead of AMD K8 HyperTransport
bridge based on new information from Andi Kleen. The AMD
HyperTransport interface is not responsible for PCI transactions
and so the re-ordering is more likely done by the VIA north bridge.
This code is subject to change if we get more information from AMD
or VIA.
PCI Express devices are excluded from doing the read flush since all
chipsets in the write_reorder list are PCI chipsets.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix interrupt test handler by adding check for IRQ assertion in
PCI_STATE register in addition to the status block updated bit.
Add test for valid ethernet address in tg3_set_mac_addr().
Add tg3_bus_string() to setup the PCI bus speed/width string for all
PCI/PCIX/PCI Express devices. This is used to print the bus type
during init_one().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix 5780 PHY related problems:
1. MAC_RX_MODE reset must be done before setting up the MAC_MODE
register on 5705_PLUS chips or the chip will stop receiving after
a while. The MAC_RX_MODE reset is needed to prevent intermittently
losing the first receive packet on serdes chips.
2. Skip MAC loopback test on 5780 because of hardware errata. Normal
traffic including PHY loopback is not affected by the errata.
3. PHY loopback fails intermittently on 5708S and this is fixed by
putting the PHY in loopback mode first before programming the MAC
mode register. A MAC_RX_MODE reset is also added.
4. Return -EINVAL in tg3_nway_reset() if device is in TBI mode. Allow
nway_reset if 5780S is in parallel detect mode.
5. Add missing PHY IDs in KNOWN_PHY_ID() macro.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix and simplify the workaround code for the 4GB boundary tx buffer
hardware bug.
1. Need to unmap the original SKB's dma addresses if a new SKB cannot
be allocated.
2. Need to pass the base flag to tigon3_4gb_hwbug_workaround() or TSO
won't work properly.
3. The guilty entry and length parameters for
tigon3_4gb_hwbug_workaround() are removed as they are not necessary.
4. Remove assumption that only one fragment can hit the 4GB boundary.
Another fragment can hit 8GB for example.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change 0 to NULL where appropriate.
Signed-off-by: Peter Hagervall <hager@cs.umu.se>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead, count them as part of rx_missed_errors.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the status tag to determine if there are new events in
tg3_interrupt_tagged(). We discussed about this a while ago with Grant
Grundler and DaveM. This scheme makes it unnecessary to clear the
updated bit in the status block when using tagged mode, and only
a simple comparison is needed to determine if there are new events.
The tp->lock around netif_rx_complete() and tg3_restart_ints() is also
removed. It is unnecessary with DaveM's new locking scheme.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary status block accesses in tg3_msi(). Since MSI is
not shared, it is unnecessary to read the status block to determine if
there are any new events in the MSI handler. It is also unnecessary to
clear the updated bit in the status block.
Since the poll list is per-cpu, tg3_poll() will be scheduled to run on
the same CPU that received the MSI. Prefetches for the status block
and the next rx descriptors are added in tg3_msi() to improve their
access times when tg3_poll() runs.
In the non-MSI irq handlers, we need to check the status block because
interrupts may be shared. Only prefetches for the next rx descriptors
are added.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve ethtool loopback self test by adding PHY loopback to the
existing MAC loopback test.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor SerDes bug fixes for 5780S and nvram bug fixes for 5780 and
5752.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is similar to Eric Dumazet's tx_lock patch for tg3 but takes it
one step further to eliminate the tx_lock in the tx_completion path
when the tx queue is not stopped.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Found a bug while reviewing the patches the second time.
The TG3_FLAG_TXD_MBOX_HWBUG flag is set after the register access
methods have been determined. This patch fixes it by moving it up before
the various access methods are assigned.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register write to register 0x68 to restart interrupts is unnecessary
as the interrupt wasn't masked in that register by the irq handler. This
will save one register write in the fast path.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the new workaround for 5703 A1/A2 if it is behind
certain ICH bridges. The workaround disables memory and uses config.
cycles only to access all registers. The 5702/03 chips can mistakenly
decode the special cycles from the ICH chipsets as memory write cycles,
causing corruption of register and memory space. Only certain ICH
bridges will drive special cycles with non-zero data during the address
phase which can fall within the 5703's address range. This is not an ICH
bug as the PCI spec allows non-zero address during special cycles.
However, only these ICH bridges are known to drive non-zero addresses
during special cycles.
The indirect_lock is also changed to spin_lock_irqsave from spin_lock_bh
because it is used in irq handler when using the indirect method to
disable interrupts.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the mailbox read method and also adds an inline function
tw32_mailbox_f() for mailbox writes that require read flush.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds various dedicated register read/write methods for the
existing workarounds, including PCIX target workaround, write with read
flush, etc. The chips that require these workarounds will use these
dedicated access functions.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the basic function pointers to do register accesses in
the fast path. This was suggested by David Miller. The idea is that
various register access methods for different hardware errata can easily
be implemented with these function pointers and performance will not be
degraded on chips that use normal register access methods.
The various register read write macros (e.g. tw32, tr32, tw32_mailbox)
are redefined to call the function pointers.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3_abort_hw() call in tg3_test_loopback() is causing lockups on
some devices. tg3_abort_hw() disables the memory arbiter, causing
tg3_reset_hw() to hang when it tries to write the pre-reset signature.
tg3_abort_hw() should only be called after the pre-reset signature has
been written. This is all done in tg3_reset_hw() so the tg3_abort_hw()
call is unnecessary and can be removed.
[ Also bump driver version and release date. -DaveM ]
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A problem was reported by Grant Grundler on an HP rx8620 using IOX
Core LAN partno(A7109-6) 5701 copper NIC. The tg3 driver mistakenly
detects this NIC as having a SerDes PHY and link does not come up as a
result.
The problem was caused by an incorrectly programmed eeprom that set the
NIC_SRAM_DATA_CFG_PHY_TYPE_FIBER bit in the NIC_SRAM_DATA_CFG location.
This patch will override the NIC_SRAM_DATA_CFG_PHY_TYPE_FIBER bit if a
valid PHY ID is read from the MII registers on older 570x chips where
the MII interface is not used on SerDes chips. On newer chips such as
the 5780 that use MII for both copper and SerDes, SerDes detection must
rely on the eeprom.
This patch will make the SerDes detection identical to versions 3.25 and
older.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Grant Grundler <iod00d@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Else on SMP systems it is possible for hotplug to execute,
invoke tg3_open(), and end up loading the uninitialized
PCI register save area into the card.
Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson