Since 43cc71eed1, the platform modalias is
prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable serial
platform drivers, to re-enable auto loading.
NOTE that Kconfig for some of these drivers doesn't allow modular builds, and
thus doesn't match the driver source's unload support. Presumably their
unload code is buggy and/or weakly tested...
[dbrownell@users.sourceforge.net: more drivers, registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Strange chars appear on the serial port when a printk and a printf
happens at the same time. This is caused by the pdc sending chars while
atmel_console_write (called from printk) is executing
Concurent access of uart and console to the same port leads to corrupted
data to be transmitted, so disable tx dma (PDC) while writing to the
console.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I found a problem related to losing data during pdc transmission in
atmel_serial: connect ttyS1 with ttyS2 using a loopback cable, send 30
byte of packet from one to the other and waiting for 30 byte. On the
other side just read and echo the data received.
We always call atmel_tx_dma() from the tasklet regardless of what interrupt
triggered it.
Signed-off-by: michael <trimarchi@gandalf.sssup.it>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There was an off-by-1 in the SCRFDR calculation that caused writes over
128-bytes to hang in the FIFO. Fix it up.
Signed-off-by: Yutaro Ebihara <ebiharaml@si-linux.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the following section mismatches:
WARNING: drivers/built-in.o(.exit.text+0x5a): Section mismatch in reference from the function of_platform_serial_exit() to the variable .devinit.data:of_platform_serial_driver
The function __exit of_platform_serial_exit() references
a variable __devinitdata of_platform_serial_driver.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit e6bafba5b4 ("wmi: (!x & y)
strikes again"), a bug was fixed that involved converting !x & y to !(x
& y). The code below shows the same pattern, and thus should perhaps be
fixed in the same way.
This is not tested and clearly changes the semantics, so it is only
something to consider.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@ expression E1,E2; @@
(
!E1 & !E2
|
- !E1 & E2
+ !(E1 & E2)
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thomas Lehmann <thomas.lehmann@alumni.tu-berlin.de> verified that this
entry works.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (35 commits)
Blackfin Serial Driver: Fix bug - Only insert UART rx char in timer task.
Blackfin Serial Driver: Fix bug - update tx dma buffer tail before wake up processes.
Blackfin Serial Driver: Fix bug - Increase buffer tail immediately before starting tx dma.
[Blackfin] serial driver: Add flow control support to bf54x
[Blackfin] serial driver: Fix bug Poll RTS/CTS status in DMA mode as well
[Blackfin] serial driver: ADSP-BF52x arch/mach support
[Blackfin] serial driver: use simpler comment headers and strip out information that is maintained in the scm's log
[Blackfin] serial driver: rework break flood anomaly handling to be more robust/realistic about what we can actually work around
[Blackfin] serial driver: fix bug - cache the bits of the LSR on systems where the LSR is read-to-clear
[Blackfin] serial driver: fix bug - should not wait for the TFI bit, just clear it when tx stop.
[Blackfin] serial driver: Fix bug serial driver in DMA mode spams history to console on shell restart
[Blackfin] serial driver: Fix bug Free rx dma buffer in shutdown.
[Blackfin] serial driver: Clean up UART DMA code.
Blackfin Serial driver: Fix bug - serial driver in PIO mode cant handle input very quickly
[Blackfin] arch: kill section mismatch warnings
[Blackfin] arch: handle the most common L1 shrinkage case (L1 does not exist for a part) so that any parts labeled for L1 instead get placed into external memory sections
[Blackfin] arch: add bfin_clear_PPIx_STATUS() helper funcs like we have for other parts
[Blackfin] arch: make sure we have proper description/copyright/license lines
[Blackfin] arch: Fix CONFIG_PM support for BF561
[Blackfin] arch: Remove DPMC char driver option
...
This header is needed on other architectures as well (namely h8300),
which currently fails to build without this in place. Rather than
duplicating the port definition completely there, just move this to a
common location instead.
This should get h8300 working again for 2.6.25, in addition to the
changes already pushed by Sato-san in -rc2.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We should only return IRQ_HANDLED when we actually found something to
handle. This is important since the USART interrupt handler may be
shared with the timer interrupt on some chips.
Pointed-out-by: michael <trimarchi@gandalf.sssup.it>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
asm/hardware.h doesn't exist any more, and the definitions sh-sci.h
depended on are provided through asm/cpu/addrspace.h these days.
Kill off the bogus include.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds sh7366 cpu supports. Just the most basic things like interrupt
controller, clocks and serial port are included at this point.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There is an outdated comment in serial_core.c also fixed.
Signed-off-by: Denis Cheng <crquan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When possible, pass the tty name to request_irq() so that the user can easily
distinguish the different serial ports in /proc/interrupts.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As pointed out by David Brownell, we really ought to be using container_of
when converting from "struct uart_port *" to "struct atmel_uart_port *".
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduced by atmel_serial-split-the-interrupt-handler.patch.
Thanks to michael <trimarchi@gandalf.sssup.it> for spotting it.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is based on the DMA-patch by Chip Coldwell for the AT91/AT32 serial
USARTS, with some tweaks to make it apply neatly on top of the other patches
in this series.
The RX and TX code has been moved to a tasklet and reworked a bit. Instead of
depending on the ENDRX and TIMEOUT bits in CSR, we simply grab as much data as
we can from the DMA buffers. I think this closes a race where the ENDRX bit
is set after we read CSR but before we read RPR, although I haven't confirmed
this.
Similarly, the two TX handlers (ENDTX and TXBUFE) have been combined into one.
Since the current code only uses a single TX buffer, there's no point in
handling those interrupts separately.
This also fixes a DMA sync bug in the original patch.
[linux@bohmer.net: rebased onto irq-splitup patch]
[hskinnemoen@atmel.com: moved to tasklet, fixed dma bug, misc cleanups]
[hskinnemoen@atmel.com: atmel_serial dma: Misc fixes and cleanups]
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Split up the interrupt handler of the serial port into a interrupt top-half
and a tasklet.
The goal is to get the interrupt top-half as short as possible to minimize
latencies on interrupts. But the old code also does some calls in the
interrupt handler that are not allowed on preempt-RT in IRQF_NODELAY context.
This handler is executed in this context because of the interrupt sharing with
the timer interrupt. The timer interrupt on Preempt-RT runs in IRQF_NODELAY
context.
The tasklet takes care of handling control status changes, pushing incoming
characters to the tty layer, handling break and other errors. It also handles
pushing TX data into the data register.
Reading the complete receive queue is still done in the top-half because we
never want to miss any incoming character.
[hskinnemoen@atmel.com: misc cleanups and simplifications]
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When an error happens in probe(), the clocks should be disabled, but
only if the port isn't already used as a console.
In remove(), the port struct shouldn't be freed because it's defined
statically.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If BRGR is zero, the baud rate generator isn't running, so the boot loader
can't have initialized the port.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace two instances of barrier() with cpu_relax() since that's the right
thing to do when busy-waiting. This does not actually change anything since
cpu_relax() is defined as barrier() on both ARM and AVR32.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean up the atmel_serial driver to conform the coding rules. It contains no
functional change.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a set of changes to implement proper resource management in the
driver, including iomem space reservation and operating on physical
addresses ioremap()ped appropriately using accessory functions rather than
unportable direct assignments.
Some adjustments to code are made to reflect the architecture of the
interface, which is a centrally controlled multiport (or, as referred to
from DEC documentation, a serial line multiplexer, going up to 8 lines
originally) rather than a bundle of separate ports.
Types are changed, where applicable, to specify the width of hardware
registers explicitly. The interrupt handler is now managed in the
->startup() and ->shutdown() calls for consistency with other drivers and
also in preparation to handle the handover from the initial firmware-based
console gracefully.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all casts from "struct uart_port *" to "struct dz_port *" with a
construct based on container_of(). This makes the conversion work
irrespective of where the former struct is located within the latter.
By popular request I have implemented it as an inline function rather than
a macro this time.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A set of changes to the way termios settings are propagated to the serial
port hardware. The DZ11 only supports a selection of fixed baud settings,
so some requests may not be fulfilled. Keep the old setting in such a case
and failing that resort to 9600bps. Also add a missing update of the
transmit timeout. And remove the explicit encoding of the line selected
from writes to the Line Parameters Register as it has been preencoded by
the ->set_termios() call already. Finally, remove a duplicate macro for
the Receiver Enable bit.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Handle the read and ignore status masks correctly. Handle the BREAK condition
as expected: a framing error with a null character is a BREAK, any other
framing error is a framing error indeed.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ->start_tx(), ->stop_tx() and ->stop_rx() backends are called with the
port's lock already taken. Remove locking from within them and wrap around
calls as necessary.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename the serial console structure so that `modpost' does not complain about
a reference to an "init" section -- "_console" is magic.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reformat the Kconfig entries and update descriptions for accuracy. Select the
driver by default for configurations of interest. For the curious: 32BIT
means only 32-bit DECstations support the device, not that the driver is not
64-bit clean; I have not checked that either though.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sort the header inclusions, add a few that are needed but pulled indirectly
only and remove ones that are not really used.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Well, panic() is a little bit undue if request_irq() fails; there is probably
no need to justify it any further. Handle the case gracefully, by
unregistering the driver.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Polled transmission is tricky enough with the DZ11 design. While "loop" is
set to a high value, conceptually you are not allowed to transmit without
checking whether the device offers the right transmission line (yes, it is the
device that selects the line -- the driver has no control over it other than
disabling the transmitter offered if it is the wrong one), so the loop has to
be run at least once.
Well, the '1977 or PDP11 view of how serial lines should be handled... Except
that the serial interface used to be quite an impressive board back then
rather than chip.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove unused module function prototypes that would not even build if enabled.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When rebasing one of the mpc5200 psc UART patches I made a mistake and
damaged the patch.
This patch fixes the compile failure introduced in commit
25ae3a0739
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Kay Sievers