Device 0x10a4 is a double 82571 on a single PCI-Express card and
has 4 gigabit capable ports.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
WoL is constantly giving problems and needed a rewrite. Consolidates
all WoL capabilities into a single function, and disables WoL for all
other ports on the device except for port A.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Remove the code that reads part_num from the EEPROM. This part number
is never displayed or queryable by the user.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Memory leak was found in 2.6.18-rc4 and e1000 7.2.7 from sourceforge: We
should free resources allocated for previous rings if following allocation
fails.
Signed-off-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
irq leak was found in 2.6.18-rc4 and e1000 7.2.7 from sourceforge: if
e1000_up fails in e1000_open() we do not free allocated irq
Signed-off-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
From: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Disable aggressive clocking on esb2 with SERDES port as it causes
hardware problems.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Allow NVM to setup LPLU for IGP2 and IGP3. Only IGP needs LPLU D3
disabled during init here.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Explicitly lock two more ethtool entry points completely instead
of the hardware reset only to prevent a race condition.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Remove pci ID 8086:1000 from the list fo supported devices. This device
has not functioned with the driver for very long (since v. 5.2.4!)
and we lack the resources to come with a substantial fix. There are only
few cards of this type out there.
Signed-off-by: Jeff Kirsher <Jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
A panic was reported when receiving 1522 size packets if using
the default MTU. we should set the initial rx buffer length to the
value that e1000changemtu sets so that we can receive any packet
that would not be dropped by LPE=0.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke.jan.h.kok@intel.com>
After removing the hardware CRC stripping which causes problems with
SOL and related issues, we need to compensate for this changed size.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
The original suggested fix for netpoll was found to be racy on SMP
kernels. While it is highly unlikely that this race would ever be seen
in the real world due to current netpoll usage models, we implemented
this updated fix to address concerns.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Use the new names.
Cc: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds the wrapper function skb_is_gso which can be used instead
of directly testing skb_shinfo(skb)->gso_size. This makes things a little
nicer and allows us to change the primary key for indicating whether an skb
is GSO (if we ever want to do that).
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the device ID's of the supported ICH8 LAN devices.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
The workaround for the ich8 lock loss problem is only needed for
a very small amount of systems. This adds an option for the user
to disable the workaround.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
This hooks up the ich8 structure into the driver itself.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
This implements the core new functions needed for ich8's internal
NIC. This includes:
* ich8 specific read/write code
* flash/nvm access code
* software semaphore flag functions
* 10/100 PHY (fe - no gigabit speed) support for low-end versions
* A workaround for a powerdown sequence problem discovered that
affects a small number of motherboard.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Hardware is reported to have problems with ERT. We disable it for
all hardware to make sure we are not seeing unexplainable user
problems.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
We were not checking the return value of get_speed_and_duplex
properly, whih may contain an error value.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
M88 rev 2 PHY needs a longer downshift to function properly. This adds
a much longer downshift counter for this specific device.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Several e1000 adapters were not blinking correctly or inconsistently. This
patch cleans this up and makes them all behave the same as far as possible.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
CRC stripping is breaking SMBUS-connected BMC's. We disable this
feature to make it work. This fixes related bugs regarding SOL.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
A certain AMD64 bridge (8132) has an option to turn on write combining
which breaks our adapter. To circumvent this we need to flush every write.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
We can take uninitialized values into account which minimizes code
and allows us to simplify the parameter checking code greatly.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Changing a printk message to make clear that this message is originating
from e1000.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Smart Power Down is a power saving feature in newer e1000 hardware. We
disable it because it causes time to link to be long, but make it a
user choice.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
buffer_info is already filled at the end of this while() loop.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
e1000_suspend is called even when !CONFIG_PM. The non-PM code inside of it
is properly #ifdef'd. This fixes the compiler warnings when !CONFIG_PM.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
In relation to the irq work done earlier we also move the PHY powerup
and powerdown functions into separate functions and move the calls to
_close and _open, making the PHY stay in it's power state as long as
the device is _up.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
After studying the driver mac reset code it was found that there
were multiple race conditions possible to reset the unit twice or
bring it e1000_up() double. This fixes all occurences where the
driver needs to reset the mac.
We also remove irq requesting/releasing into _open and _close so
that while the device is _up we will never touch the irq's. This fixes
the double free irq bug that people saw.
To make sure that the watchdog task doesn't cause another race we let
it run as a non-scheduled task.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Ethtool was reporting that loopback failed randomly on esb2
systems. Upon study it was found that the phy manual was changed
with respect to the loopback mode bits. The new value fixes it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Having separate fields in sk_buff for TSO/UFO (tso_size/ufo_size) is not
going to scale if we add any more segmentation methods (e.g., DCCP). So
let's merge them.
They were used to tell the protocol of a packet. This function has been
subsumed by the new gso_type field. This is essentially a set of netdev
feature bits (shifted by 16 bits) that are required to process a specific
skb. As such it's easy to tell whether a given device can process a GSO
skb: you just have to and the gso_type field and the netdev's features
field.
I've made gso_type a conjunction. The idea is that you have a base type
(e.g., SKB_GSO_TCPV4) that can be modified further to support new features.
For example, if we add a hardware TSO type that supports ECN, they would
declare NETIF_F_TSO | NETIF_F_TSO_ECN. All TSO packets with CWR set would
have a gso_type of SKB_GSO_TCPV4 | SKB_GSO_TCPV4_ECN while all other TSO
packets would be SKB_GSO_TCPV4. This means that only the CWR packets need
to be emulated in software.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a PCI bus error/fault triggers a PCI bus reset, attempts to get the
ethernet packet count statistics from the hardware will fail, returning
garbage data upstream. This patch skips statistics data collection if the
PCI device is not on the bus.
This patch presumes that an earlier patch,
[PATCH] PCI Error Recovery: e1000 network device driver
has already been applied.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If a PCI bus error/fault triggers a PCI bus reset, attempts to get
the ethernet packet count statistics from the hardware will fail,
returning garbage data upstream. This patch skips statistics data
collection if the PCI device is not on the bus.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Acked-by: Auke Kok <auke-jan.h.kok@intel.com>
Various PCI bus errors can be signaled by newer PCI controllers.
This patch adds the PCI error recovery callbacks to the intel gigabit
ethernet e1000 device driver. The patch has been tested, and appears
to work well.
Signed-off-by: Linas Vepstas <linas@linas.org>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
It was brought to our attention that the prefetches break e1000 traffic
on xscale/arm architectures. Remove them for now. We'll let them
stay in mm for a while, or find a better solution to enable.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
New code added in 2.6.17 caused setup_irq to print a warning when
running ethtool -t eth0 offline.
This test marks the request_irq call made by this test as a "probe"
to see if the interrupt is shared or not.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Someone was waaay too aggressive and removed e1000's reboot notifier
instead of porting it to the new way of the shutdown handler. This change
broke wake on lan. Add the shutdown handler back in using the same method
as e100 uses.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
(cherry picked from c653e6351e commit)
Someone was waaay too aggressive and removed e1000's reboot notifier
instead of porting it to the new way of the shutdown handler. This change
broke wake on lan. Add the shutdown handler back in using the same method
as e100 uses.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Update skb with the real packet size.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Seems there was a bit of a fix needed to due a bad merge in the legacy
receive path. Fixes a panic due to skb_over_panic.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Recent patch was mismerged in the miitool path. e1000_media_type_copper
was being compared with the phy type instead of the media type.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Add the sourceforge project mailinglist to the contact information.
Bump version to 7.0.38-k2
Update copyright string with the new year.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Implement more efficient locking (avoid the lock) when checking for
a stopped queue. Also don't wake the queue unless the threshold is
reached to avoid queue on/off thrash.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Remove multi-descriptor support from legacy recieve path
Add memory usage efficiency by using more correct size descriptors for
small MTU sizes and optimize using LPE for <= 1522 byte frame sizes
An extra performance fix that effected our TCP window size growth
as a receiver. Set our initial buffer to be 128 bytes instead of 256
to prevent over-socket charge when truesize is computed in the stack.
old way: truesize = 256 + l1 = 256 + 1460 = 1716
new way: truesize = 128 + l1 = 128 + 1460 = 1588
The magic value that we can't cross is 1648.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Removal of unused rx_dropped counter.
Removed reference to E1000_CTRL_EXT_CANC which is no longer valid,
replaced with E1000_CTRL_EXT_INT_TIMER_CLR
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Update skb with the real packet size.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Made an adapter struct variable into a local (txb2b)
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Esb2 link didn't return after wol disable. The code previously assumed
that writing reset to PHY_CTRL phy register turned the phy back on.
In the ESB2 phy case that didn't occur.
Add ESB2 to acquire/release_hw functions upon review it was
discovered that esb2 was skipped on these functions
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
remove DPRINTKs that were printing warnings about power management on
2.4 kernels. Since we really don't react differently these printk
statements are not needed. This code was originally added to fix
some compile time warnings that got fixed by newer kernels.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner, contains unlikely() and can better optimized away.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Get rid of the old __dev_put macro that is just a hold over from pre 2.6
kernel. And turn dev_hold into an inline instead of a macro.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
return -E_NO_BIG_ENDIAN_TESTING;
[E1000]: Fix 4 missed endianness conversions on RX descriptor fields.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch moves prototypes of global variables and functions to a header
file.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: John Ronciak <john.ronciak@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For some reason, E1000's ->hard_start_xmit() routine returns -EFAULT
instead of one of the NETDEV_TX_* error codes. In fact, it frees up
the SKB before returning this. This makes the queueing layer think
the packet should be requeued and subsequently we corrupt a freed
object.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Paul Rolland reported that e1000 was having a hard time using mii-tool to set speed and duplex. This patch fixes the issue on both newer hardware as well as fixing the code issue that originally caused the problem.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
- this implementation of prefetch was tested on new and old hardware
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
- Add restriction for ESB2 to MTU size <=9216
- Removed FIFO errors which were not being used
- Fixed issues with loopback
- Power management change for saving state and config space
- WA to disable recieves and reset device on link loss. Reset needed to be done outside the interrupt context - modified existing tx_timeout_task
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
- Simplified by calling skb_fill_page_desc(), which is more efficient.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
A recent patch attempted to enable more efficient memory usage by using
only 2kB descriptors for jumbo frames. The method used to implement this
has since been commented upon as "illegal" and in recent kernels even
causes a BUG when receiving ip fragments while using jumbo frames.
This patch simply goes back to the way things were. We expect some
complaints due to order 3 allocations failing to come back due to this
change.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
in attempting to not send the "prefetch" patch, we broke the receive code,
this patch fixes that issue.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Added e1000_mc_addr_list_update
Added e1000_read_reg_io
Added e1000_enable_pciex_master
These are not static functions, that is why we have them declared in the header.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
These functions help restore the driver to active configuration when coming out of resume for power management.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Align the prefetches to a dword to help speed them up.
Recycle skb's and early replenish.
Force memory writes to complete before fetching more descriptors.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Adds the ability to disability packet split at compile time and use the legacy receive path on PCI express hardware. Made this a CONFIG option and modified the Kconfig, to reflect the new option.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Improves small packet performance with large amounts of reassembly being done in the stack.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This was to fix compilation warnings. Also added log messages when pci_enable_* functions return with an error.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This is two patches, the first is adding additional bus information for the 8257{1|2|3} controllers. The second patch was orginally a community patch to print bus type/speed/width, and enhanced by us.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The EEPROM image version is reported as a firmware version for these controllers.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Added 82571 fiber to WOL fix for dual port adapters.
Added support for 82546GB (Quad Copper).
Added PCIe typedef for x2, igp cable length 115, and extended TX CTRL registers.
Added parity error detection and PCIe CTRL registers.
Added EEPROM config registers.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed an issue netpoll would error out during communication, generating the following error:
--netdump[14973]: Got toomany timeouts in handshaking, ...
Even after a kernel panic, netpoll requires two way communication to successfully transfer the crash log to the remote server.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Simplified the logic used to assign the frame_size.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed VLAN support by switching control over to the firmware.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed by moving code to correct location (for 82572 and 82571 controllers).
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed the collision distance for 82543 controllers and newer.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Removed duplicate code, TXDCTL and TXDCTL_COUNT_DESC are the same bit and there is no need to set it twice.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
These were two separate community submitted patches.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed the TX timeout logic to use "end of packet" rather than "next to clean". Updated message log.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch contains two fixes. The first fix is to the tx and rx descriptor rings clean up process. The second fix is to jumbo frames, which cleans up the code logic and removes most of the fifo related limitations on jumbo frames. This is because the driver code now supports splitting a packet across multiple descriptors.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
10/100 speeds seem to have some problems reporting false tx timeouts especially at half duplex. Fixed by using a timeout factor to attempt to mitigate the false timeouts.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed flow control water marks based on PBA size.
Store flow control state in original_fc in addition to fc.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed read_eeprom logic to test use_eerd instead of testing for 82573 controllers.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed the loopback logic to work for the PCI express adapters.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed stats when using multiple queues.
When multiple queues are enabled, log a message in syslog.
Fixed memory allocation for multiple queues.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix adapter structure to handle multiple queues and prepping the driver for full multiple queue support, some changes are ifdef'd our unless you define CONFIG_E1000_MQ.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Updated the e1000_stats structure and removed mpx for rx_errors and rx_dropped.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Added a delay to allow PHY configuration to complete before accessing NVM.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The 82573 controller required different logic than 82571|2 controllers. Corrected the reset logic for 8257{1|2|3} controllers.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix so that if a SoL/IDER session is active, do not allow operations which require a PHY reset and instead log a message.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
These fixes update the TX and RX ring structures. Prepare driver for up-coming fixes.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed the TSO workaround for 82571/2 controllers.
Fixed TSO issue where a non-tso packet in a linear SKB which followed a TSO packet would get written back prematurely.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Partition PBA for Jumbo frames based on MTU size.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix an invalid memory reference in the e1000 driver which would cause
kernel panic.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Jeb Cramer <cramerj@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- TSO workaround
- Fixes eeprom version reporting
- Fix loopback test
- Fix for WOL
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Parse outgoing packets in e1000_transfer_dhcp_info as raw packet even if
protocol bits are set. pump, for instance causes kernel panic on some
systems, if parsed via udp header.
Thanks to Derrell Lipman <Derrell.Lipman@BacklotTech.com> for reporting and
testing.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
In e1000_free_desc_rings, zero-out pointers after the memory they
point to is freed. The test rings are static and get re-used, and
failures during subsequent test setups can cause e1000_free_desc_rings
to get called with dirty pointers. Dirty pointers can cause oopses
or crashes...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In e1000_loopback_test, make sure to call e1000_free_desc_rings if
e1000_setup_loopback_test fails. Currently in that case it will not
get called, causing a leak.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch contains the following possible cleanups:
- make needlessly global code static
- #if 0 the following unused global functions:
- e1000_hw.c: e1000_mc_addr_list_update
- e1000_hw.c: e1000_read_reg_io
- e1000_hw.c: e1000_enable_pciex_master
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/e1000/e1000_main.c:3645: warning: `e1000_suspend' defined
but not used
Signed-off-by: Ashutosh Naik <ashutosh_naik@adaptec.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Allocate node local tx and rx descriptors for the e1000 driver
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Cc: Christoph Lameter <clameter@engr.sgi.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
e1000_suspend is only used under #ifdef CONFIG_PM. Move the declaration of
it to be the same way, just like e1000_resume, otherwise gcc whines on
compile. I offer as evidence:
static struct pci_driver e1000_driver = {
.name = e1000_driver_name,
.id_table = e1000_pci_tbl,
.probe = e1000_probe,
.remove = __devexit_p(e1000_remove),
/* Power Managment Hooks */
#ifdef CONFIG_PM
.suspend = e1000_suspend,
.resume = e1000_resume
#endif
};
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Driver version, white space, comments, device id & other
Originally posted on 8/31 (and perhaps before)...I think it has not
been committed because the patch from that posting was damaged. I'm
reposting to make sure it gets in... :-)
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
drivers/net/e1000/e1000_main.c: In function `e1000_intr':
drivers/net/e1000/e1000_main.c:3156: error: `i' undeclared (first use in this function)
drivers/net/e1000/e1000_main.c:3156: error: (Each undeclared identifier is reported only once
drivers/net/e1000/e1000_main.c:3156: error: for each function it appears in.)
This function is foul.
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Flush shadow RAM to save updates to ASF related bits for 82573 controllers.
These bits are past the first 63 words of NVM.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
added msleep_interruptible delay right before returning from diag_test to allow
the phy to recover from reset
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixes for packet split related issues
* On platforms where PAGE_SIZE > 4K, driver will use only required number of
pages compared to always using 3 pages.
* Packet split won't be used if the PAGE_SIZE is > 16K
* Adds a statistics counter to splits.
* Setting the non Null ptr to zero sized buffers to solve packet split
receive descriptor error
* When the no of pages needed is calculated, the header buffer is not
included for a given MTU.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Enable custom configuration bits for 82571/2 controllers. The bits are
required for correct functionality of these controllers.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
defines/modifies data structures, function prototypes and changes to the
driver rendering it capable of handling <n> tx/rx queues
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Do not count frames dropped by the hardware as part of rx_dropped.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix remaining bits of u32 vs. pm_message confusion. Should not break
anything.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/net/e1000/e1000_main.c: In function `e1000_clean_tx_irq':
drivers/net/e1000/e1000_main.c:2774: warning: size_t format, dma_addr_t arg (arg 8)
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Suggested by Steven Rostedt, matches his patch included in e100.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sys_reboot() now calls device_suspend(), so it is no longer necessary for
the e1000 driver to register a reboot notifier [in fact doing so results in
e1000_suspend() getting called twice].
(akpm: we need to fast-track this. It's causing ia64 to oops on shutdown)
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: <cramerj@intel.com>
Cc: <john.ronciak@intel.com>
Cc: <ganesh.venkatesan@intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Driver version, white space, comments & other
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Included proposals to false late collisions due to H/W latencies
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Ethtool set speed/duplex validates parameters for consistency
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Ethtool cleanup patch from Stephen Hemminger
* use ADVERTISED_xxx fields when setting advertised fields
* don't hardcode constant for advertised field
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Fixed the loopback test failure for 82573 based adapters
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Fixed register and loopback test failures with 82573 controllers
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Cleanup debug message printed when Tx Unit hang is detected
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Use netdev_priv() to get to netdev->priv - from shemminger@osdl.org
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Use correct WOL settings for 82544 adapters
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
This patch fixes an obvious and nasty bug where we could exit the transmit
routine while holding tx_lock.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Implement 82546 errata 10 -- first Tx descriptor cannot have more than 2015 byte of data in it or it could hang the transmitter.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
diff -up net-drivers-2.6/drivers/net/e1000/e1000_main.c net-drivers-2.6/drivers/net/e1000.new/e1000_main.c
Dump information on Tx ring when 'NETDEV: Watchdog' condition is reached
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
diff -up net-drivers-2.6/drivers/net/e1000/e1000_main.c net-drivers-2.6/drivers/net/e1000.new/e1000_main.c
Delay clean-up of last Tx packet to fix pre-mature writeback issue of Tx descriptors only when TSO is enabled
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
diff -up net-drivers-2.6/drivers/net/e1000/e1000_main.c net-drivers-2.6/drivers/net/e1000.new/e1000_main.c
Fix kernel panic with 82541 LOM when using a 100M cable
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
diff -up net-drivers-2.6/drivers/net/e1000/e1000_main.c net-drivers-2.6/drivers/net/e1000.new/e1000_main.c
Enable polling before enabling interrupts -- avoids (in NAPI mode) entering the ISR and returning without doing any work because polling is not enabled. [romieu@fr.zoriel.com]
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
diff -up net-drivers-2.6/drivers/net/e1000/e1000_main.c net-drivers-2.6/drivers/net/e1000.new/e1000_main.c
Fix msec-delay definition in e1000_osdep.h to use msleep
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
diff -up net-drivers-2.6/drivers/net/e1000/e1000_osdep.h net-drivers-2.6/drivers/net/e1000.new/e1000_osdep.h
Added enhanced functionality to the loopback diags to wrap the descriptor rings.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
diff -up net-drivers-2.6/drivers/net/e1000/e1000_ethtool.c net-drivers-2.6/drivers/net/e1000.new/e1000_ethtool.c
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Jesse Brandeburg