The SCIF peer bus is used to register and unregister SCIF peer devices
internally by the SCIF driver to signify the addition and removal of
peer nodes respectively from the SCIF network. This simplifies remote node
handling within SCIF and will also be used to support device probe/remove
for SCIF client drivers (e.g. netdev over SCIF)
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SCIF hardware bus abstracts the low level hardware driver details
like interrupts and mapping remote memory so that the same SCIF driver
can work without any changes with the MIC host or card driver as long
as the hardware bus operations are implemented. The SCIF hardware
device is registered by the host and card drivers on the SCIF hardware
bus resulting in probing the SCIF driver.
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCIF ring buffer is a single producer, single consumer byte stream
ring buffer optimized for avoiding reads across the PCIe bus while
adding the required barriers and hardware workarounds for the MIC
Coprocessor. The ring buffer is used to implement a receive queue for
SCIF driver messaging between two nodes and for byte stream messaging
between SCIF endpoints. The existing in-kernel ring buffer was not
reused since it has not been designed for our use across the PCIe bus
where each node runs an independent OS. Each SCIF node has a receive
queue for every other SCIF node, and each connected endpoint has a
receive queue for messages from its peer. This pair of receive
queues is referred to as a SCIF queue pair.
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CARMA project has ended, and the hardware has all been moved into
storage. It is unlikely to ever be used again.
Remove the drivers so that there is no more maintenance burden from
ongoing upstream kernel changes.
Signed-off-by: Ira W. Snyder <ira.snyder@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
since we move all nfc hanling to the mei_phy module
we can kill mei_cl_ops
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
move nfc logic to mei_phy module, we prefer as much as
possible not to deal with a particualr client protocol
in the mei generic infrasutcutre
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Export name and uuid via sysfs and uevent
Cc: linux-api@vger.kernel.org
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to automate modules matching add device uuid
which is reported in client enumeration, keep also
the name that is needed in for nfc distinguishing radio vendor
Report mei:name:uuid
Cc: linux-api@vger.kernel.org
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The io callback is clear from write_waitling_list after
we receive interrupt from the hw to ack the write completion.
We need to wait for this interrupt deliver before we try
to enter low power state
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On longer non-blocking write might not complete at the end of
autosuspend expiration, therefore we request autosuspend
again on the write completion.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Consume the write flow control on the first chunk of the write instead
of on the buffer completion.
We can safely assume that the consequent chunks have the flow control
granted.
This addresses two issues:
1. Blocks other callbacks from the same client riding on the client's
flow control and prevents interleaving of messages as FW cannot distinguish
between two messages from the same client.
2. Fixes single buffer flow control arbitration in a clean way, without
connection/disconnection book keeping
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add client info to debug prints in the read function to
ease on debugging efforts.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can receive mtu with one call now, no need to store it.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This should be used for debug only.
The feaure is gated by "allow_fixed_address" control exposed in debugfs.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed address is simplified FW client that doesn't require
connection and doesn't support flow control.
So it can be only one host client per fixed FW client.
Fixed client access is available only for drivers on mei bus,
connection from user-space is blocked.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For ME clients that use single receiving buffer
the driver tracks credentials on mei_me_clients structure
for all connections. The driver needs to book keep the shared
resource correctly and track the connections, particularly
the credit has to be cleaned when there is no active connection
to a particular me client. This solves issue when subsequent
connection will not get an ill impression that it can write.
We add active connection counter the particular ME client and
when the counter reach zero, we clear the credits.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Keep a pointer to associated me client in the host client object to
eliminate me client searches. Check if the me client is active in the
firmware by checking if its is linked on the me clients list
Add accessors for the me client properties from host client.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify connect state machine by changing the logic around
Connection request in progress - only check if we have a callback in
relevant queue.
Extract common code into mei_cl_send_connect() function
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split disconnected state into two parts first reception disconnect
response from the firmware and second actually setting of disconnected
state. Book keeping data are needed for processing and after firmware
disconnected the client and are cleaned when setting the disconnected
state in mei_cl_set_disconneted() function.
Add mei_cl_send_disconnect to reduce code duplication.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HW has to be in known state before the initialisation
sequence is started. The polling step for settling aliveness
was set to 200ms while in practise this can be done in up to 30msecs.
Cc: <stable@vger.kernel.org> #3.18+
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Barak Yoresh <barak.yoresh@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big char/misc driver patchset for 4.1-rc1.
Lots of different driver subsystem updates here, nothing major, full
details are in the shortlog below.
All of this has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlU2IMEACgkQMUfUDdst+yloDQCfbyIRL23WVAn9ckQse/y8gbjB
OT4AoKTJbwndDP9Kb/lrj2tjd9QjNVrC
=xhen
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the big char/misc driver patchset for 4.1-rc1.
Lots of different driver subsystem updates here, nothing major, full
details are in the shortlog.
All of this has been in linux-next for a while"
* tag 'char-misc-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (133 commits)
mei: trace: remove unused TRACE_SYSTEM_STRING
DTS: ARM: OMAP3-N900: Add lis3lv02d support
Documentation: DT: lis302: update wakeup binding
lis3lv02d: DT: add wakeup unit 2 and wakeup threshold
lis3lv02d: DT: use s32 to support negative values
Drivers: hv: hv_balloon: correctly handle num_pages>INT_MAX case
Drivers: hv: hv_balloon: correctly handle val.freeram<num_pages case
mei: replace check for connection instead of transitioning
mei: use mei_cl_is_connected consistently
mei: fix mei_poll operation
hv_vmbus: Add gradually increased delay for retries in vmbus_post_msg()
Drivers: hv: hv_balloon: survive ballooning request with num_pages=0
Drivers: hv: hv_balloon: eliminate jumps in piecewiese linear floor function
Drivers: hv: hv_balloon: do not online pages in offline blocks
hv: remove the per-channel workqueue
hv: don't schedule new works in vmbus_onoffer()/vmbus_onoffer_rescind()
hv: run non-blocking message handlers in the dispatch tasklet
coresight: moving to new "hwtracing" directory
coresight-tmc: Adding a status interface to sysfs
coresight: remove the unnecessary configuration coresight-default-sink
...
Pull vfs update from Al Viro:
"Part one:
- struct filename-related cleanups
- saner iov_iter_init() replacements (and switching the syscalls to
use of those)
- ntfs switch to ->write_iter() (Anton)
- aio cleanups and splitting iocb into common and async parts
(Christoph)
- assorted fixes (me, bfields, Andrew Elble)
There's a lot more, including the completion of switchover to
->{read,write}_iter(), d_inode/d_backing_inode annotations, f_flags
race fixes, etc, but that goes after #for-davem merge. David has
pulled it, and once it's in I'll send the next vfs pull request"
* 'for-linus-1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (35 commits)
sg_start_req(): use import_iovec()
sg_start_req(): make sure that there's not too many elements in iovec
blk_rq_map_user(): use import_single_range()
sg_io(): use import_iovec()
process_vm_access: switch to {compat_,}import_iovec()
switch keyctl_instantiate_key_common() to iov_iter
switch {compat_,}do_readv_writev() to {compat_,}import_iovec()
aio_setup_vectored_rw(): switch to {compat_,}import_iovec()
vmsplice_to_user(): switch to import_iovec()
kill aio_setup_single_vector()
aio: simplify arguments of aio_setup_..._rw()
aio: lift iov_iter_init() into aio_setup_..._rw()
lift iov_iter into {compat_,}do_readv_writev()
NFS: fix BUG() crash in notify_change() with patch to chown_common()
dcache: return -ESTALE not -EBUSY on distributed fs race
NTFS: Version 2.1.32 - Update file write from aio_write to write_iter.
VFS: Add iov_iter_fault_in_multipages_readable()
drop bogus check in file_open_root()
switch security_inode_getattr() to struct path *
constify tomoyo_realpath_from_path()
...
Pull x86 asm changes from Ingo Molnar:
"There were lots of changes in this development cycle:
- over 100 separate cleanups, restructuring changes, speedups and
fixes in the x86 system call, irq, trap and other entry code, part
of a heroic effort to deobfuscate a decade old spaghetti asm code
and its C code dependencies (Denys Vlasenko, Andy Lutomirski)
- alternatives code fixes and enhancements (Borislav Petkov)
- simplifications and cleanups to the compat code (Brian Gerst)
- signal handling fixes and new x86 testcases (Andy Lutomirski)
- various other fixes and cleanups
By their nature many of these changes are risky - we tried to test
them well on many different x86 systems (there are no known
regressions), and they are split up finely to help bisection - but
there's still a fair bit of residual risk left so caveat emptor"
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (148 commits)
perf/x86/64: Report regs_user->ax too in get_regs_user()
perf/x86/64: Simplify regs_user->abi setting code in get_regs_user()
perf/x86/64: Do report user_regs->cx while we are in syscall, in get_regs_user()
perf/x86/64: Do not guess user_regs->cs, ss, sp in get_regs_user()
x86/asm/entry/32: Tidy up JNZ instructions after TESTs
x86/asm/entry/64: Reduce padding in execve stubs
x86/asm/entry/64: Remove GET_THREAD_INFO() in ret_from_fork
x86/asm/entry/64: Simplify jumps in ret_from_fork
x86/asm/entry/64: Remove a redundant jump
x86/asm/entry/64: Optimize [v]fork/clone stubs
x86/asm/entry: Zero EXTRA_REGS for stub32_execve() too
x86/asm/entry/64: Move stub_x32_execvecloser() to stub_execveat()
x86/asm/entry/64: Use common code for rt_sigreturn() epilogue
x86/asm/entry/64: Add forgotten CFI annotation
x86/asm/entry/irq: Simplify interrupt dispatch table (IDT) layout
x86/asm/entry/64: Move opportunistic sysret code to syscall code path
x86, selftests: Add sigreturn selftest
x86/alternatives: Guard NOPs optimization
x86/asm/entry: Clear EXTRA_REGS for all executable formats
x86/signal: Remove pax argument from restore_sigcontext
...
fix warning:
include/trace/ftrace.h:28:0: note: this is the location of the previous definition
^
In file included from include/trace/define_trace.h:90:0,
from drivers/misc/mei/mei-trace.h:76,
from drivers/misc/mei/mei-trace.c:21:
include/trace/ftrace.h:28:0: warning: "TRACE_SYSTEM_STRING" redefined
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is our remaining set of three fixes for 4.0: two oops fixes(one for cable
pulls triggering oopses and the other be2iscsi specific) and one warn on in
sysfs on multipath devices using enclosures.
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJVKFlCAAoJEDeqqVYsXL0MjOsH/j0DIeMOa7p5JdryKZNY+LY4
HHfVgAK4T+bNZQUOCq/Dctn19CltuJGoDGkY2P4m1YG+mz8NLCm2aEAKp9efhho6
6cLv0An/PlQhFuurbzo9BXsEb93ZENf6ng0WJZ3iOyqD9FA9X+0mDAfXDfJ4mwH3
aGa0NE4bbqhNotWjpdFPIDqU2uwk4pV3M/BRx3JmeIIR2BtaWXkKxTq5tmLo9DDN
22Seu/RJqV7O3WdphLLoN+615eCcroOru54DnQtKQ3/pQeC+6gyHcjkq02KjJ9D+
wBNltUrtqzreDrgF2D6uaxT3NkQFFPlkzjD6Ma5tq5637sT9Tch8/UNTMzs5UgU=
=AbF2
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is our remaining set of three fixes for 4.0: two oops fixes(one
for cable pulls triggering oopses and the other be2iscsi specific) and
one warn on in sysfs on multipath devices using enclosures"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
Defer processing of REQ_PREEMPT requests for blocked devices
be2iscsi: Fix kernel panic when device initialization fails
enclosure: fix WARN_ON removing an adapter in multi-path devices
This adds support for the the wakeup threshold and
support for the second wakeup unit to the DT based
setup.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
st,axis-{x,y,z} can be negative to imply inverted
axis.
Apart from that the minimal and maximal threshold
may be negative.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function mei_cl_is_transitioning is just opposite
of mei_cl_is_connected. What we actually wanted to
check is if we lost connection so we can discard
the check for transition and check for 'not connected'
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace open coded check for cl->state !=/== MEI_FILE_CONNECTED
with mei_cl_is_connected function.
Note that cl->state != MEI_FILE_CONNECTED is not the same
as cl->state == MEI_FILE_DISCONNECTED
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mei_poll returned with POLLIN w/o checking whether the operation
has really completed.
remove redundant check and locking in amthif specific handler
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci core now disables msi on probe automatically,
drop this from device-specific code.
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have peculiar problems with multi-path and enclosures: physically, we know
each bay can only be occupied by a single disk device. However in multi-path,
it appears we have many (because each path to the device appears in Linux as a
different kernel device). We try to fix this by only having the last seen
device show up in the bay.
Sysfs gets very annoyed if we try to manipulate links when the kobject sysfs
directory (kobj.sd) doesn't exist and drops a huge WARN_ON which most users
panic and report an oops for. This happens on a few path removal situations
and IBM reports seeing it when one of their multi-path adapters is removed.
Add a check to enclosure device removal for the existence the sysfs directory
containing both the forward and back links so that the remnants (if any) get
removed in either direction but no scary warnings are dumped.
Reported-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Tested-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
struct kiocb now is a generic I/O container, so move it to fs.h.
Also do a #include diet for aio.h while we're at it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
return type of wait_for_completion_timeout is unsigned long not int. The
rc variable is renamed timeout to reflect its use and the type adjusted to
unsigned long.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
return type of wait_for_completion_timeout is unsigned long not int. The
rc variable is renamed timeout to reflect its use and the type adjusted to
unsigned long.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
return type of wait_for_completion_timeout is unsigned long not int. The
rc variable is in use for other calls so an additional timeout variable
of type unsigned long is added.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In mei_host_client_init function we enable the all internal
connected clients including NFC. This is done before we set the device
to enabled state and let userspace call open.
We need to check only for MEI_FILE_CONNECTED in mei_cl_is_connected
in order to enable the communication with the clients before
MEI_DEV_ENABLED is set.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current maximum size of a queue in a queue pair is 128 MB. If
we increase that in the future, the queue pair allocation routines
may run into overflow issues. This change adds additional checks
to guard against this.
Acked-by: Andy King <acking@vmware.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that the size filled in by userland in the datagram header
matches the size of the buffer passed down in the IOCTL. Note that we
account for the size of the header itself in the check.
Acked-by: Jorgen Hansen <jhansen@vmware.com>
Acked-by: Aditya Sarwade <asarwade@vmware.com>
Signed-off-by: Andy King <acking@vmware.com>
Reported-by: David Ramos <daramos@stanford.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As of 240ddd495a (vmw_vmci: Convert driver to use get_user_pages_fast())
we no longer user get_user_pages(), thus update the warning.
Also convert to pr_debug, which is a more appropriate level of logging.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
user_mode_vm() and user_mode() are now the same. Change all callers
of user_mode_vm() to user_mode().
The next patch will remove the definition of user_mode_vm.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brad Spengler <spender@grsecurity.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/43b1f57f3df70df5a08b0925897c660725015554.1426728647.git.luto@kernel.org
[ Merged to a more recent kernel. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently, the SRAM allocator returns device memory via ioremap.
This causes issues on ARM64 when the internal SoC SRAM allocated by
the generic sram driver is used for audio playback. The destination
buffer address (which is ioremapped SRAM) is not 64-bit aligned for
certain streams (e.g. 44.1k sampling rate). In such cases we get
unhandled alignment faults. Use ioremap_wc in place of ioremap which
gives us normal non-cacheable memory instead of device memory.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bh1780gli driver does not create an i2c module alias for the
device it supports, preventing the driver from being loaded
automatically when needed on non-OF/DT systems. Add it.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
call device's disable handler prior to disconnection
so it can possibly close the communication with fw client
in graceful way
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace clunky read state machine with read stack
implemented as per client read list, this is important
mostly for mei drivers with unsolicited reads
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify disposal of io callback by removing the callback
implicitly from its lookup list inside mei_io_cb_free
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We set the operation type at initialization time as each cb is used only
for a single type of operation
As a byproduct we add a convenient wrapper for allocating cb with
the data buffer.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The callback structure is used exclusively for reading or writing
therefore there is no reason to hold both response and request buffers
in the callback structure
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reduce code duplication in amthif by reusing
regular client read functions.
The change also removes the need for amthif
own buffering
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reduce code duplication in amthif code by reusing
regular client write functions.
Add completed flag to cb so amthif client can add
rx credits on write completion
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reuse common client mechanism for sending flow control
hbm message. Add new function mei_amthif_read_start
similar to mei_cl_read_start that puts control flow request
onto the control write queue and drop mei_amthif_irq_read function
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
iamthif_ioctl is obsolete and can be safely dropped
Currently it is set to true during driver runtime
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On failure mei_amthif_irq_read_msg returns an error
that will cause device reset but the issue is software one
so instead we should propagate error to caller and just
clean the read queues.
As a side effect also removes useless BUG_ONs
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On memory allocation failure mei_cl_irq_read_msg will
return with error that will cause device reset.
Instead we should propagate error to caller and
just clean the read queues.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Align functions names in KDoc with real ones.
Fix comment format to be KDoc and fix wrong syntax there.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current power gating naming was confusing,
we wish to swap meanings of register and flow level power gating terms,
For registers writing level use terms set and unset:
mei_me_pg_set, mei_me_pg_unset
For flow/high level use power gating enter and power gating exit terms
mei_me_pg_enter_sync, mei_me_pg_exit_sync
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To make debugging a bit easier we add me register
access tracing
<debugfs>/tracing/events/mei/mei_reg_{read,write}
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. Use mei_device structure as the first argument to the io
register access wrappers so we'll have access to the device
structure needed for tracing.
2. Use wrapper consistently
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. Use rw lock to access the me_clients list
2. Reuse already defined find functions also when
removing particular me client
3. Add wrappers for addition and deletion
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the internal device state to to disabled after hardware reset in stop flow.
This will cover cases when driver was not brought to disabled state because of
an error and in stop flow we wish not to retry the reset.
Cc: <stable@vger.kernel.org> #3.10+
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big char/misc driver update for 3.20-rc1.
Lots of little things in here, all described in the changelog. Nothing
major or unusual, except maybe the binder selinux stuff, which was all
acked by the proper selinux people and they thought it best to come
through this tree.
All of this has been in linux-next with no reported issues for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlTgs80ACgkQMUfUDdst+yn86gCeMLbxANGExVLd+PR46GNsAUQb
SJ4AmgIqrkIz+5LCwZWM02ldbYhPeBVf
=lfmM
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc patches from Greg KH:
"Here's the big char/misc driver update for 3.20-rc1.
Lots of little things in here, all described in the changelog.
Nothing major or unusual, except maybe the binder selinux stuff, which
was all acked by the proper selinux people and they thought it best to
come through this tree.
All of this has been in linux-next with no reported issues for a while"
* tag 'char-misc-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (90 commits)
coresight: fix function etm_writel_cp14() parameter order
coresight-etm: remove check for unknown Kconfig macro
coresight: fixing CPU hwid lookup in device tree
coresight: remove the unnecessary function coresight_is_bit_set()
coresight: fix the debug AMBA bus name
coresight: remove the extra spaces
coresight: fix the link between orphan connection and newly added device
coresight: remove the unnecessary replicator property
coresight: fix the replicator subtype value
pdfdocs: Fix 'make pdfdocs' failure for 'uio-howto.tmpl'
mcb: Fix error path of mcb_pci_probe
virtio/console: verify device has config space
ti-st: clean up data types (fix harmless memory corruption)
mei: me: release hw from reset only during the reset flow
mei: mask interrupt set bit on clean reset bit
extcon: max77693: Constify struct regmap_config
extcon: adc-jack: Release IIO channel on driver remove
extcon: Remove duplicated include from extcon-class.c
Drivers: hv: vmbus: hv_process_timer_expiration() can be static
Drivers: hv: vmbus: serialize Offer and Rescind offer
...
Including:
- Update of all defconfigs
- Addition of a bunch of config options to modernise our defconfigs
- Some PS3 updates from Geoff
- Optimised memcmp for 64 bit from Anton
- Fix for kprobes that allows 'perf probe' to work from Naveen
- Several cxl updates from Ian & Ryan
- Expanded support for the '24x7' PMU from Cody & Sukadev
- Freescale updates from Scott:
"Highlights include 8xx optimizations, some more work on datapath device
tree content, e300 machine check support, t1040 corenet error reporting,
and various cleanups and fixes."
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xDU3
-----END PGP SIGNATURE-----
Merge tag 'powerpc-3.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
- Update of all defconfigs
- Addition of a bunch of config options to modernise our defconfigs
- Some PS3 updates from Geoff
- Optimised memcmp for 64 bit from Anton
- Fix for kprobes that allows 'perf probe' to work from Naveen
- Several cxl updates from Ian & Ryan
- Expanded support for the '24x7' PMU from Cody & Sukadev
- Freescale updates from Scott:
"Highlights include 8xx optimizations, some more work on datapath
device tree content, e300 machine check support, t1040 corenet
error reporting, and various cleanups and fixes"
* tag 'powerpc-3.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (102 commits)
cxl: Add missing return statement after handling AFU errror
cxl: Fail AFU initialisation if an invalid configuration record is found
cxl: Export optional AFU configuration record in sysfs
powerpc/mm: Warn on flushing tlb page in kernel context
powerpc/powernv: Add OPAL soft-poweroff routine
powerpc/perf/hv-24x7: Document sysfs event description entries
powerpc/perf/hv-gpci: add the remaining gpci requests
powerpc/perf/{hv-gpci, hv-common}: generate requests with counters annotated
powerpc/perf/hv-24x7: parse catalog and populate sysfs with events
perf: define EVENT_DEFINE_RANGE_FORMAT_LITE helper
perf: add PMU_EVENT_ATTR_STRING() helper
perf: provide sysfs_show for struct perf_pmu_events_attr
powerpc/kernel: Avoid initializing device-tree pointer twice
powerpc: Remove old compile time disabled syscall tracing code
powerpc/kernel: Make syscall_exit a local label
cxl: Fix device_node reference counting
powerpc/mm: bail out early when flushing TLB page
powerpc: defconfigs: add MTD_SPI_NOR (new dependency for M25P80)
perf/powerpc: reset event hw state when adding it to the PMU
powerpc/qe: Use strlcpy()
...
This is the usual grab bag of driver updates (hpsa, storvsc, mp2sas,
megaraid_sas, ses) plus an assortment of minor updates. There's also an
update to ufs which adds new phy drivers and finally a new logging
infrastructure for SCSI.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJU2Ty5AAoJEDeqqVYsXL0M9rAH/1xNpAxXuxQq+dW5Z+uOaX60
5RRIu7/xA1HEfzkT5FTHrolmogDjVqawu4PZS66iHDeo05RBVUlbTA8qCK+MlRcN
U6s0cLEw59eH3EaCfOGuYp/MnbhuV0eNxe0btmqJIQwuW3+gwZKGJdOq6LS2YasJ
k/DyIBVmkJAVsN56vm9q2vbtcZp+Bg+ngqBS+SC4TF7vV1WCtFmS6yaUf62PYW3D
+Irx37qHZntDR5wdw3dsuKDi5U8bl6myPjaVLnVJqg/WIF9RlCkjk5xpWT99AmVO
NmtYQxLLBlAQ5K+sIlBUwxZe+8q1l+Aj4TTmJHAfFtyfp25s7JR9I6/QtOyC5Kw=
=odol
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"This is the usual grab bag of driver updates (hpsa, storvsc, mp2sas,
megaraid_sas, ses) plus an assortment of minor updates.
There's also an update to ufs which adds new phy drivers and finally a
new logging infrastructure for SCSI"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (114 commits)
scsi_logging: return void for dev_printk() functions
scsi: print single-character strings with seq_putc
scsi: merge consecutive seq_puts calls
scsi: replace seq_printf with seq_puts
aha152x: replace seq_printf with seq_puts
advansys: replace seq_printf with seq_puts
scsi: remove SPRINTF macro
sg: remove an unused variable
hpsa: Use local workqueues instead of system workqueues
hpsa: add in P840ar controller model name
hpsa: add in gen9 controller model names
hpsa: detect and report failures changing controller transport modes
hpsa: shorten the wait for the CISS doorbell mode change ack
hpsa: refactor duplicated scan completion code into a new routine
hpsa: move SG descriptor set-up out of hpsa_scatter_gather()
hpsa: do not use function pointers in fast path command submission
hpsa: print CDBs instead of kernel virtual addresses for uncommon errors
hpsa: do not use a void pointer for scsi_cmd field of struct CommandList
hpsa: return failed from device reset/abort handlers
hpsa: check for ctlr lockup after command allocation in main io path
...
We were missing a return statement in the PSL interrupt handler in the
case of an AFU error, which would trigger an "Unhandled CXL PSL IRQ"
warning. We do actually handle these type of errors (by notifying
userspace), so add the missing return IRQ_HANDLED so we don't throw
unecessary warnings.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If an AFU claims to have a configuration record but doesn't actually
contain a vendor and device ID, fail the AFU initialisation. Right now
this is just a way of politely letting AFU developers know that they
need to fix their config space, but later on we may expose the AFUs as
actual PCI devices in their own right and don't want to inadvertendly
expose an AFU with a bad config space.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
An AFU may optionally contain one or more PCIe like configuration
records, which can be used to identify the AFU.
This patch adds support for exposing the raw config space and the
vendor, device and class code under sysfs. These will appear in a
subdirectory of the AFU device corresponding with the configuration
record number, e.g.
cat /sys/class/cxl/afu0.0/cr0/vendor
0x1014
cat /sys/class/cxl/afu0.0/cr0/device
0x4350
cat /sys/class/cxl/afu0.0/cr0/class
0x120000
hexdump -C /sys/class/cxl/afu0.0/cr0/config
00000000 14 10 50 43 00 00 00 00 06 00 00 12 00 00 00 00 |..PC............|
00000010 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
*
00000100
These files behave in much the same way as the equivalent files for PCI
devices, with one exception being that the config file is currently
read-only and restricted to the root user. It is not necessarily
required to be this strict, but we currently do not have a compelling
use-case to make it writable and/or world-readable, so I erred on the
side of being restrictive.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The big issue here is:
of_property_read_u32(np, "flow_cntrl", (u32 *)&dt_pdata->flow_cntrl);
"->flow_cntrl" is a char so when we write a 32 bit number to it then it
corrupts past the end of the char. It's probably hard to notice because
the struct has padding so the code works on little endian systems. But
on a big endian system the code would fail and on a 64 bit, big endian
systems then "nshutdown_gpio" and "baud_rate" would be buggy as well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We might enter the interrupt handler with hw_ready already set,
but prior we actually started the reset flow.
To soleve this we move the reset release from the interrupt handler
to the HW start wait function which is part of the reset sequence.
Cc: <stable@vger.kernel.org> #3.10+
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should mask interrupt set bit when writing back
hcsr value in reset bit clean-up.
This is refinement for
mei: clean reset bit before reset
commit b13a65ef19
Cc: <stable@vger.kernel.org> #3.10+
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When unbinding and rebinding the driver on a system with a card in PHB0, this
error condition is reached after a few attempts:
ERROR: Bad of_node_put() on /pciex@3fffe40000000
CPU: 0 PID: 3040 Comm: bash Not tainted 3.18.0-rc3-12545-g3627ffe #152
Call Trace:
[c000000721acb5c0] [c00000000086ef94] .dump_stack+0x84/0xb0 (unreliable)
[c000000721acb640] [c00000000073a0a8] .of_node_release+0xd8/0xe0
[c000000721acb6d0] [c00000000044bc44] .kobject_release+0x74/0xe0
[c000000721acb760] [c0000000007394fc] .of_node_put+0x1c/0x30
[c000000721acb7d0] [c000000000545cd8] .cxl_probe+0x1a98/0x1d50
[c000000721acb900] [c0000000004845a0] .local_pci_probe+0x40/0xc0
[c000000721acb980] [c000000000484998] .pci_device_probe+0x128/0x170
[c000000721acba30] [c00000000052400c] .driver_probe_device+0xac/0x2a0
[c000000721acbad0] [c000000000522468] .bind_store+0x108/0x160
[c000000721acbb70] [c000000000521448] .drv_attr_store+0x38/0x60
[c000000721acbbe0] [c000000000293840] .sysfs_kf_write+0x60/0xa0
[c000000721acbc50] [c000000000292500] .kernfs_fop_write+0x140/0x1d0
[c000000721acbcf0] [c000000000208648] .vfs_write+0xd8/0x260
[c000000721acbd90] [c000000000208b18] .SyS_write+0x58/0x100
[c000000721acbe30] [c000000000009258] syscall_exit+0x0/0x98
We are missing a call to of_node_get(). pnv_pci_to_phb_node() should
call of_node_get() otherwise np's reference count isn't incremented and
it might go away. Rename pnv_pci_to_phb_node() to pnv_pci_get_phb_node()
so it's clear it calls of_node_get().
Signed-off-by: Ryan Grimm <grimm@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(this is a resend of this patch. Originally sent last year, but post
appears to have been lost)
This change fixes two bugs in the VMCI host driver related to mapping
the notify boolean from user space into kernel space:
- the actual UVA was rounded up to the next page boundary - resulting
in memory corruption in the calling process whenever notifications
would be signalled. This has been fixed by just removing the
PAGE_ALIGN part, since get_user_pages_fast can figure this out on
its own
- the mapped page wasn't stored anywhere, so it wasn't unmapped and
put back when a VMCI context was destroyed. Fixed this by
remembering the page.
Acked-by: Andy King <acking@vmware.com>
Acked-by: Darius Davis <darius@vmware.com>
Signed-off-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
if(!wait_for_completion_interruptible_timeout(...))
only handles the timeout case - this patch adds handling the
signal case the same as timeout.
Only the timeout case was being handled, the signal case
(-ERESTARTSYS) was treated just like the case of successful
completion, which is most likely not reasonable.
read_local_version() is called from download_firmware() where
it checks for !=0 return, so the error handling logic should be
preserved correctly.
download_firmware() is called from st_kim_start() which is
checking for !=0 return, so the error handling logic should be
preserved correctly
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To support dynamic addition and removal of
me clients we add reference counter.
Update kdoc with locking requirements.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds reset to sysfs which will PERST the card. If load_image_on_perst is set
to "user" or "factory", the PERST will cause that image to be loaded.
load_image_on_perst is set to "user" for production.
"none" could be used for debugging. The PSL trace arrays are preserved which
then can be read through debugfs.
PERST also triggers CAPP recovery. An HMI comes in, which is handled by EEH.
EEH unbinds the driver, calls into Sapphire to reinitialize the PHB, then
rebinds the driver.
Signed-off-by: Ryan Grimm <grimm@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Turning snoops on is the last step in CAPP recovery. Sapphire is expected to
have reinitialized the PHB and done the previous recovery steps.
Add mode argument to opal call to do this. Driver can turn snoops off although
it does not currently.
Signed-off-by: Ryan Grimm <grimm@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
load_image_on_perst identifies whether a PERST will cause the image to be
flashed to the card. And if so, which image.
Valid entries are: "none", "user" and "factory".
A value of "none" means PERST will not cause the image to be flashed. A
power cycle to the pcie slot is required to load the image.
"user" loads the user provided image and "factory" loads the factory image upon
PERST.
sysfs updates the cxl struct in the driver then calls cxl_update_image_control
to write the vals in the VSEC.
Signed-off-by: Ryan Grimm <grimm@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Select defaults such that a PERST causes flash image reload. Select which
image based on what the card is set up to load.
CXL_VSEC_PERST_LOADS_IMAGE selects whether PERST assertion causes flash image
load.
CXL_VSEC_PERST_SELECT_USER selects which image is loaded on the next PERST.
cxl_update_image_control writes these bits into the VSEC.
Signed-off-by: Ryan Grimm <grimm@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds tracepoints throughout the cxl driver, which can provide
insight into:
- Context lifetimes
- Commands sent to the PSL and AFU and their completion status
- Segment and page table misses and their resolution
- PSL and AFU interrupts
- slbia calls from the powerpc copro_fault code
These tracepoints are mostly intended to aid in debugging (particularly
for new AFU designs), and may be useful standalone or in conjunction
with hardware traces collected by the PSL (read out via the trace
interface in debugfs) and AFUs.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
hwirq has not been initialized, however it is being incremented
and also not being referenced in a loop. This error was detected with
cppcheck:
[drivers/misc/cxl/irq.c:439]: (error) Uninitialized variable: hwirq
Commit 80fa93fce3 ("cxl: Name interrupts in /proc/interrupt")
introduced this error.
This is a simple fix that removes the redundant increment.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-By: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Here are 3 small driver fixes for reported issues for 3.19-rc5. All of
these have been in linux-next for a while with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlS5VzYACgkQMUfUDdst+ylv5gCfT8krEtuWXM1NMZwIuftf4Whb
z8cAn23whaxGED7AyBRVXxMohYF8Vxq9
=yMIV
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are three small driver fixes for reported issues for 3.19-rc5.
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mcb: mcb-pci: Only remap the 1st 0x200 bytes of BAR 0
mei: add ABI documentation for fw_status exported through sysfs
mei: clean reset bit before reset
This patch solves the blank line warning of checkpatch.pl
Signed-off-by: Mohammad Jamal <md.jamalmohiuddin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the break statements present after return
Signed-off-by: Mohammad Jamal <md.jamalmohiuddin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added a blank line after declaration to fix the warning of checkpatch.pl
Signed-off-by: Mohammad Jamal <md.jamalmohiuddin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The loop for measuring the square wave periods over some cycles is
refactored to be more easily readable. This includes avoiding a
"by-hand-implemented" for loop with a "real" one and adding some
comments.
Furthermore the following compiler warning is avoided by this patch:
drivers/misc/ioc4.c: In function ‘ioc4_probe’:
drivers/misc/ioc4.c:194:16: warning: ‘start’ may be used uninitialized
in this function [-Wmaybe-uninitialized]
period = (end - start) /
^
drivers/misc/ioc4.c:148:11: note: ‘start’ was declared here
uint64_t start, end, period;
^
Signed-off-by: Richard Leitner <dev@g0hl1n.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We encounter situations where we got bad packet type from the
UART (probably due to platform problem or UART driver issues)
which caused us out of boundary array access,
which eventually led to kernel panic.
Signed-off-by: Amir Ayun <amira@ti.com>
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Leonid Iziumtsev <x0153368@ti.com>
Signed-off-by: Gigi Joseph <gigi.joseph@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case the debugfs creation fails the whole init process was failing.
There is no need to do this as the shared transport can work without it.
Fix it so it just reports the failure and continue.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Gigi Joseph <gigi.joseph@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend/resume was failing if callbacks were not registered.
As it is ok not to do anything when suspending fix this
so it soen't return an error and allow the system to suspend.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Gigi Joseph <gigi.joseph@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sudeep Dutt