These functions are defined but no longer used.
Compile tested only.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we're using GFP_KERNEL, however there are some path(s) where we
can hold some spinlocks, specifically bond->curr_slave_lock:
[ 4.722916] BUG: sleeping function called from invalid context at mm/slub.c:965
[ 4.724438] in_atomic(): 1, irqs_disabled(): 0, pid: 940, name: ifup-eth
[ 4.726034] 5 locks held by ifup-eth/940:
...snip...
[ 4.734646] #4: (&bond->curr_slave_lock){+...+.}, at: [<ffffffffa00badc6>] bond_enslave+0xda6/0xdd0 [bonding]
...snip...
[ 4.759081] [<ffffffffa00b6f11>] bond_change_active_slave+0x191/0x3b0 [bonding]
[ 4.760917] [<ffffffffa00b7227>] bond_select_active_slave+0xf7/0x1d0 [bonding]
[ 4.762751] [<ffffffffa00badce>] bond_enslave+0xdae/0xdd0 [bonding]
...snip...
As it's out of hot path and is a really rare event - change the gfp_t flags
to GFP_ATOMIC to avoid sleeping under spinlock.
v2: convert new notify calls to GFP_ATOMIC.
CC: Thomas Glanzmann <thomas@glanzmann.de>
CC: Ding Tianhong <dingtianhong@huawei.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/mwifiex/pcie.c
net/ipv6/sit.c
The SIT driver conflict consists of a bug fix being done by hand
in 'net' (missing u64_stats_init()) whilst in 'net-next' a helper
was created (netdev_alloc_pcpu_stats()) which takes care of this.
The two wireless conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we're only sending arp requests if we have a route to the target
(and, thus, can find out the source ip address).
There are some use cases, however, where we don't want/need to set an ip
address (or set up a specific route) for bonding to use arp monitoring *for
traffic generation*. We can easily send arp probes (arp requests with src
ip == 0) to generate arp broadcast responses from the target ip and use
them for determining if the target is up.
This, obviously, won't work with arp validation - because we don't have the
ip address set and, thus, will filter out the responses. So in that case -
print a warning.
CC: François CACHEREUL <f.cachereul@alphalink.fr>
CC: Zhenjie Chen <zhchen@redhat.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enslaving a bond to itself leads to an endless loop and hangs the kernel.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Tested-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a bug in the slave release function which leads the transmit
functions which use the bond->slave_cnt to a div by 0 because we might
just have released our last slave and made slave_cnt == 0 but at the same
time we may have a transmitter after the check for an empty list which will
fetch it and use it in the slave id calculation.
Fix it by moving the slave_cnt after synchronize_rcu so if this was our
last slave any new transmitters will see an empty slave list which is
checked after rcu lock but before calling the mode transmit functions
which rely on bond->slave_cnt.
Fixes: 278b208375 ("bonding: initial RCU conversion")
CC: Veaceslav Falico <vfalico@redhat.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Veaceslav has reported and fix this problem by commit f2ebd477f1
(bonding: restructure locking of bond_ab_arp_probe()). According Jay's
opinion, the current solution is not very well, because the notification
is to indicate that the interface has actually changed state in a meaningful
way, but these calls in the ab ARP monitor are internal settings of the flags
to allow the ARP monitor to search for a slave to become active when there are
no active slaves. The flag setting to active or backup is to permit the ARP
monitor's response logic to do the right thing when deciding if the test
slave (current_arp_slave) is up or not.
So the best way to fix the problem is that we should not send a notification
when the slave is in testing state, and check the state at the end of the
monitor, if the slave's state recover, avoid to send pointless notification
twice. And RTNL is really a big lock, hold it regardless the slave's state
changed or not when the current_active_slave is null will loss performance
(every 100ms), so we should hold it only when the slave's state changed and
need to notify.
I revert the old commit and add new modifications.
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The problem was introduced by the commit 1d3ee88ae0
(bonding: add netlink attributes to slave link dev).
The bond_set_active_slave() and bond_set_backup_slave()
will use rtmsg_ifinfo to send slave's states, so these
two functions should be called in RTNL.
In 802.3ad mode, acquiring RTNL for the __enable_port and
__disable_port cases is difficult, as those calls generally
already hold the state machine lock, and cannot unconditionally
call rtnl_lock because either they already hold RTNL (for calls
via bond_3ad_unbind_slave) or due to the potential for deadlock
with bond_3ad_adapter_speed_changed, bond_3ad_adapter_duplex_changed,
bond_3ad_link_change, or bond_3ad_update_lacp_rate. All four of
those are called with RTNL held, and acquire the state machine lock
second. The calling contexts for __enable_port and __disable_port
already hold the state machine lock, and may or may not need RTNL.
According to the Jay's opinion, I don't think it is a problem that
the slave don't send notify message synchronously when the status
changed, normally the state machine is running every 100 ms, send
the notify message at the end of the state machine if the slave's
state changed should be better.
I fix the problem through these steps:
1). add a new function bond_set_slave_state() which could change
the slave's state and call rtmsg_ifinfo() according to the input
parameters called notify.
2). Add a new slave parameter which called should_notify, if the slave's state
changed and don't notify yet, the parameter will be set to 1, and then if
the slave's state changed again, the param will be set to 0, it indicate that
the slave's state has been restored, no need to notify any one.
3). the __enable_port and __disable_port should not call rtmsg_ifinfo
in the state machine lock, any change in the state of slave could
set a flag in the slave, it will indicated that an rtmsg_ifinfo
should be called at the end of the state machine.
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bond_xxx_info_query() was already in RTNL, so no need to use
bond lock to protect the bond slave list, so remove it.
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bond_info_show_master already in RCU read-side critical section,
and the we access curr_active_slave without the curr_slave_lock, we
could not sure whether the curr_active_slave will be changed during
the processing, so use RCU to protected the pointer.
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __netpoll_setup() will check the slave's flag and ndo_poll_controller just
like the slave_dev_support_netpoll() does, and slave_dev_support_netpoll() was
not used by any place, so remove it.
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bond->curr_active_slave can be changed between its deferences, even to
NULL, and thus we might panic.
We're always holding the rcu (rx_handler->bond_handle_frame()->bond_arp_rcv())
so fix this by rcu_dereferencing() it and using the saved.
Reported-by: Ding Tianhong <dingtianhong@huawei.com>
Fixes: aeea64a ("bonding: don't trust arp requests unless active slave really works")
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Acked-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the error case return early.
Make the normal return at the bottom of the function.
Reduces indent for readability.
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's unnecessary and less readable after a clause ending in a goto.
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's smaller and faster for some architectures.
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_3ad.h
drivers/net/bonding/bond_main.c
Two minor conflicts in bonding, both of which were overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
To reflect the new meaning.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
slave->jiffies is updated every time the slave becomes active, which, for
bonding, means that its link is 'up'.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all the logic is handled via last_arp_rx, we don't need to use
last_rx.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that last_arp_rx correctly show the last time we've received an ARP, we
can use it safely instead of slave->dev->last_rx.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that last_arp_rx really has the last time we've received any (validated or
not) ARP, we can use it in slave_last_rx() instead of slave->dev->last_rx.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the options are in place - arp_validate can be set to receive all
the traffic or only arp packets to verify if the slave is up, when the
slave isn't validated.
CC: Rob Landley <rob@landley.net>
CC: "David S. Miller" <davem@davemloft.net>
CC: Nikolay Aleksandrov <nikolay@redhat.com>
CC: Ding Tianhong <dingtianhong@huawei.com>
CC: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we can either receive any traffic as a proff of slave being up,
or only *validated* arp traffic (i.e. with src/dst ip checked).
Add an option to be able to specify if we want to receive non-validated arp
traffic only.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we only set bond_arp_rcv() if we're using arp_validate, however
this makes us skip updating last_arp_rx if we're not validating incoming
ARPs - thus, if arp_validate is off, last_arp_rx will never be updated.
Fix this by always setting up recv_probe = bond_arp_rcv, even if we're not
using arp_validate.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we're updating the last_arp_rx only when we've validate the
packet, however afterwards we use it as 'ANY last packet received', but not
only validated ARPs.
Fix this by updating it in case of any packet received. It won't break the
arp_validation=0 because we, anyway, return the correct slave->dev->last_rx in
slave_last_rx().
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently it's disabled because it's sometimes hard, in typical configs, to
make it work - because of the nature how the loadbalance modes work - as
it's hard to deliver valid arp replies to correct slaves by the switch.
However we still can use arp_validation in loadbalance with several other
configs, per example with arp_validate == 2 for backup with one broadcast
domain, without the switch(es) doing any balancing - this way we'd be (a
bit more) sure that the slave is up.
So, enable it to let users decide which one works/suits them best. Also
correct the mode limitation from BOND_OPT_ARP_VALIDATE.
CC: Nikolay Aleksandrov <nikolay@redhat.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Acked-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're always called with rcu_read_lock() held (bond_arp_rcv() is only
called from bond_handle_frame(), which is rx_handler and always called
under rcu from __netif_receive_skb_core() ).
The slave active/passive and/or bonding params can change in-flight, however
we don't really care about that - we only modify the last time packet was
received, which is harmless.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Acked-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
aggregator_identifier is used to assign unique aggregator identifiers
to aggregators of a bond during device enslaving.
aggregator_identifier is currently a global variable that is zeroed in
bond_3ad_initialize().
This sequence will lead to duplicate aggregator identifiers for eth1 and eth3:
create bond0
change bond0 mode to 802.3ad
enslave eth0 to bond0 //eth0 gets agg id 1
enslave eth1 to bond0 //eth1 gets agg id 2
create bond1
change bond1 mode to 802.3ad
enslave eth2 to bond1 //aggregator_identifier is reset to 0
//eth2 gets agg id 1
enslave eth3 to bond0 //eth3 gets agg id 2
Fix this by making aggregator_identifier private to the bond.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new argument for ndo_select_queue() callback that passes a
fallback handler. This gets invoked through netdev_pick_tx();
fallback handler is currently __netdev_pick_tx() as most drivers
invoke this function within their customized implementation in
case for skbs that don't need any special handling. This fallback
handler can then be replaced on other call-sites with different
queue selection methods (e.g. in packet sockets, pktgen etc).
This also has the nice side-effect that __netdev_pick_tx() is
then only invoked from netdev_pick_tx() and export of that
function to modules can be undone.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ether_addr_copy is smaller and faster for some architectures.
This relies on a stack frame being at least __aligned(2)
for one use of an Ethernet address on the stack.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing terminating newlines.
Convert uses of pr_info to pr_cont in bond_check_params.
Standardize upper/lower case styles.
Typo fixes, remove unnecessary parentheses and periods.
Alignment neatening.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use more current logging style.
Coalesce formats, realign arguments, drop unnecessary periods.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/bonding/bond_options.c includes rwlock.h directly,
which is a nono, and which also breaks RT kernel build.
Signed-off-by: Mike Galbraith <bitbucket@online.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_valid_name() will check the buffer length for input name, no need to
check it twice.
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_set_mac_address() will check the dev->netdev_ops->ndo_set_mac_address,
so no need to check it in bond_set_mac_address().
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bonding driver take write locks and spin locks that are shared
by the tx path in enslave processing and notification processing,
If the netconsole is in use, the bonding can call printk which puts
us in the netpoll tx path, if the netconsole is attached to the bonding
driver, result in deadlock.
So add protection for these place, by checking the netpoll_block_tx
state, we can defer the sending of the netconsole frames until a later
time using the retransmit feature of netpoll_send_skb that is triggered
on the return code NETDEV_TX_BUSY.
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bond enslave processing don't hold bond->lock anymore,
so release an unlocked rw lock will cause warning message,
remove the unwanted read_unlock(&bond->lock).
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fail_over_mac could be set to active or follow in any time for all modes,
so if the fail_over_mac is not none and the current mode is not active-backup,
the bond_set_mac_address() could not change the master and slave's MAC address.
In bond_set_mac_address(), the fail_over_mac should only affect AB mode, so modify
to check the mode in addition to fail_over_mac when setting bond's MAC address.
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to bonding.txt, the fail_over_ma should only affect active-backup mode,
but I found that the fail_over_mac could be set to active or follow in all
modes, this will cause new slave could not be set to bond's MAC address at
enslave processing and restore its own MAC address at removal processing.
The correct way to fix the problem is that we should not add restrictions when
setting options, just need to modify the bond enslave and removal processing
to check the mode in addition to fail_over_mac when setting a slave's MAC during
enslavement. The change active slave processing already only calls the fail_over_mac
function when in active-backup mode.
Thanks for Jay's suggestion.
The patch also modify the pr_warning() to pr_warn().
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 1d3ee88ae0
(bonding: add netlink attributes to slave link dev)
has add rtmsg_ifinfo() in bond_set_active_slave() and
bond_set_backup_slave(), so the two function need to
called in RTNL lock, but bond_loadbalance_arp_mon()
only calling these functions in RCU, warning message
will occurs.
fix this by add a new function bond_slave_state_change(),
which will reset the slave's state after slave link check,
so remove the bond_set_xxx_slave() from the cycle and only
record the slave_state_changed, this will call the new
function to set all slaves to new state in RTNL later.
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we're calling it from under RCU context, however we're using some
functions that require rtnl to be held.
Fix this by restructuring the locking - don't call it under any locks,
aquire rcu_read_lock() if we're sending _only_ (i.e. we have the active
slave present), and use rtnl locking otherwise - if we need to modify
(in)active flags of a slave.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently bond_ab_arp_probe() is always called under rcu_read_lock(),
however to work with curr_active_slave we're still holding the
curr_slave_lock.
To remove that curr_slave_lock - rcu_dereference the bond's
curr_active_slave and use it further - so that we're sure the slave won't
go away, and we don't care if it will change in the meanwhile.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) BPF debugger and asm tool by Daniel Borkmann.
2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.
3) Correct reciprocal_divide and update users, from Hannes Frederic
Sowa and Daniel Borkmann.
4) Currently we only have a "set" operation for the hw timestamp socket
ioctl, add a "get" operation to match. From Ben Hutchings.
5) Add better trace events for debugging driver datapath problems, also
from Ben Hutchings.
6) Implement auto corking in TCP, from Eric Dumazet. Basically, if we
have a small send and a previous packet is already in the qdisc or
device queue, defer until TX completion or we get more data.
7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.
8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
Borkmann.
9) Share IP header compression code between Bluetooth and IEEE802154
layers, from Jukka Rissanen.
10) Fix ipv6 router reachability probing, from Jiri Benc.
11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.
12) Support tunneling in GRO layer, from Jerry Chu.
13) Allow bonding to be configured fully using netlink, from Scott
Feldman.
14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
already get the TCI. From Atzm Watanabe.
15) New "Heavy Hitter" qdisc, from Terry Lam.
16) Significantly improve the IPSEC support in pktgen, from Fan Du.
17) Allow ipv4 tunnels to cache routes, just like sockets. From Tom
Herbert.
18) Add Proportional Integral Enhanced packet scheduler, from Vijay
Subramanian.
19) Allow openvswitch to mmap'd netlink, from Thomas Graf.
20) Key TCP metrics blobs also by source address, not just destination
address. From Christoph Paasch.
21) Support 10G in generic phylib. From Andy Fleming.
22) Try to short-circuit GRO flow compares using device provided RX
hash, if provided. From Tom Herbert.
The wireless and netfilter folks have been busy little bees too.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
net/cxgb4: Fix referencing freed adapter
ipv6: reallocate addrconf router for ipv6 address when lo device up
fib_frontend: fix possible NULL pointer dereference
rtnetlink: remove IFLA_BOND_SLAVE definition
rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
qlcnic: update version to 5.3.55
qlcnic: Enhance logic to calculate msix vectors.
qlcnic: Refactor interrupt coalescing code for all adapters.
qlcnic: Update poll controller code path
qlcnic: Interrupt code cleanup
qlcnic: Enhance Tx timeout debugging.
qlcnic: Use bool for rx_mac_learn.
bonding: fix u64 division
rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
sfc: Use the correct maximum TX DMA ring size for SFC9100
Add Shradha Shah as the sfc driver maintainer.
net/vxlan: Share RX skb de-marking and checksum checks with ovs
tulip: cleanup by using ARRAY_SIZE()
ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
net/cxgb4: Don't retrieve stats during recovery
...
stephen hemminger