Make the dock station driver a platform device driver so that
we can create sysfs entries under /sys/device/platform.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch cleans up the recently added backlight device support by Holger
Macht <hmacht@suse.de> to fit well with the rest of the code, using the
ibms struct as the other "subdrivers" in ibm-acpi.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
This patch makes it possible to disable ibm-acpi non-generic bay support,
as generic bay support already works well for a number of ThinkPads.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
This patch adds support for the ultrabay on the T60, X60 and other new
ThinkPads that have a SATA ultrabay.
I intend to keep bay and dock support in ibm-acpi working and updated until
it finally gets deprecated and removed in favour of the generic dock and
bay support. But we aren't there yet.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
This patch implements a fan control safety watchdog, by request of the
authors of userspace fan control scripts.
When the watchdog timer expires, the equivalent action of a "fan enable"
command is executed. The watchdog timer is reset at every reception of a
fan control command that could change the state of the fan itself.
This command is meant to be used by userspace fan control daemons, to make
sure the fan is never left set to an unsafe level because of userspace
problems.
Users of the X31/X40/X41 "speed" command are on their own, the current
implementation of "speed" is just too incomplete to be used safely,
anyway. Better to never use it, and just use the "level" command instead.
The watchdog is programmed using echo "watchdog <number>" > fan, where
number is the number of seconds to wait before doing an "enable", and zero
disables the watchdog.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
A few ThinkPads fail to initialize EC register 0x2f both in the EC
firmware and ACPI DSDT. If the BIOS and the ACPI DSDT also do not
initialize it, then the initial status of that register does not
correspond to reality.
On all reported buggy machines, EC 0x2f will read 0x07 (fan level 7) upon
cold boot, when the EC is actually in mode 0x80 (auto mode). Since
returning a text string ("unknown") would break a number of userspace
programs, instead we correct the reading for the most probably correct
answer, and return it is in auto mode.
The workaround flags the status and level as unknown on module load/kernel
boot, until we are certain at least one fan control command was issued,
either by us, or by something else.
We don't work around the bug by doing a "fan enable" at module
load/startup (which would initialize the EC register) because it is not
known if these ThinkPad ACPI DSDT might have set the fan to level 7
instead of "auto" (we don't know if they can do this or not) due to a
thermal condition, and we don't want to override that, should they be
capable of it.
We should be setting the workaround flag to "status known" upon resume, as
both reports and a exaustive search on the DSDT tables at acpi.sf.net show
that the DSDTs always enable the fan on resume, thus working around the
bug. But since we don't have suspend/resume handlers in ibm-acpi yet and
the "EC register 0x2f was modified" logic is likely to catch the change
anyway, we don't.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
This patch changes the ThinkPad Embedded Controller DMI matching
code to store the firmware version of the EC for later usage, e.g.
for quirks.
It also prints the firmware version when starting up.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
This patch extend fan control functions, implementing enable/disable for
all write access modes, implementing level control for all level-capable
write access modes.
The patch also updates the documentation, explaining levels auto and
disengaged.
ABI changes:
1. Support level 0 as an equivalent to disable
2. Add support for level auto and level disengaged when doing
EC 0x2f fan control
3. Support enable/disable for all level-based write access modes
4. Add support for level command on FANS thinkpads, as per
thinkwiki reports
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
This patch fix fan enable to attempt to do the right thing and not slow
down the fan if it is forced to the maximum speed. It also extends fan
enable to work on older thinkpads.
ABI changes:
1. Support enable/disable for all level-based write access modes
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
This patch fixes fan_read to return correct values for all fan access
modes. It also implements some fan access mode status output that was
missing, and normalizes the proc fan abi to return consistent data across
all fan read/write modes.
Userspace ABI changes and extensions:
1. Return status: enable/disable for *all* modes
(this actually improves compatibility with userspace utils!)
2. Return level: auto and level: disengaged for EC 2f access mode
3. Return level: <number> for EC 0x2f access mode
4. Return level 0 as well as "disabled" in level-aware modes
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
This patch cleans up fan_write so that it is much easier to read and
extend. It separates the proc api handling from the operations themselves.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
This patch breaks fan_read mechanics into a generic function to get fan
status and speed, and leaves only the procfs interface code in fan_read.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
This patch cleans up fan_read so that it is much easier to read and
extend.
The patch fixes the userspace ABI to return "status: not supported" (like
all other ibm-acpi functions) when neither fan status or fan control are
possible.
It also fixes the userspace ABI to return EIO if ACPI access to the EC
fails, instead of returning "status: unreadable" or "speed: unreadable".
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
This patch lays some groundwork for a fan_read and fan_write cleanup in the
next patches. To do so, it provides a new fan_init initializer, and also some
constants (through enums).
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
This patch extends ibm-acpi to support reading thermal sensors directly
through ACPI EC register access. It uses a DMI match to detect ThinkPads
with a new-style embedded controller, that are known to have forward-
compatible register maps and use 0x00 to fill in non-used registers and
export thermal sensors at EC offsets 0x78-7F and 0xC0-C7.
Direct ACPI EC register access is implemented for 8-sensor and 16-sensor
new-style ThinkPad controller firmwares as an experimental feature. The
code does some limited sanity checks on the temperatures read through EC
access, and will default to the old ACPI TMP0-7 mode if anything is amiss.
Userspace ABI is not changed for 8 sensors, but /proc/acpi/ibm/thermal is
extended for 16 sensors if the firmware supports 16 sensors.
A documentation update is also provided.
The information about the ThinkPad register map was determined by studying
ibm-acpi "ecdump" output from various ThinkPad models, submitted by
subscribers of the linux-thinkpad mailinglist. Futher information was
gathered from the DSDT tables, as they describe the EC register map in
recent ThinkPads.
DSDT source shows that TMP0-7 access and direct register access are
actually the same thing on these firmwares, but unfortunately IBM never
did update their DSDT EC register map to export TMP8-TMP15 for the second
range of sensors.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
This patch consolidades all decisions regarding the strategy to be used to
read thinkpad thermal sensors into a single enum, and refactors the
thermal sensor reading code to use a much more readable (and easier to
extend) switch() construct, in a separate function.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
ibm-acpi uses sub-device names like ibm/hotkey, which get in the way of
a sysfs conversion. Fix it to use ibm_hotkey instead. Thanks to Zhang
Rui for noticing this.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Conflicts:
drivers/ata/libata-scsi.c
include/linux/libata.h
Futher merge of Linus's head and compilation fixups.
Signed-Off-By: David Howells <dhowells@redhat.com>
Conflicts:
drivers/infiniband/core/iwcm.c
drivers/net/chelsio/cxgb2.c
drivers/net/wireless/bcm43xx/bcm43xx_main.c
drivers/net/wireless/prism54/islpci_eth.c
drivers/usb/core/hub.h
drivers/usb/input/hid-core.c
net/core/netpoll.c
Fix up merge failures with Linus's head and fix new compilation failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
Change ACPI to use dev_archdata instead of firmware_data
This patch changes ACPI to use the new dev_archdata on i386, x86_64
and ia64 (is there any other arch using ACPI ?) to store it's
acpi_handle.
It also removes the firmware_data field from struct device as this
was the only user.
Only build-tested on x86
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
processor_perflib.c::acpi_processor_ppc_notifier() check if the value
returned by the processor's _PPC method is 0 and return failed if so.
This is wrong since 0 indicate that the bios think the processor can go
to the highest frequency. This patch for example fix the HP NX 6125 to
allow its highest frequency to be available.
Signed-off-by: Bruno Ducrot <ducrot@poupinou.org>
Cc: "Pallipadi, Venkatesh" <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pass the work_struct pointer to the work function rather than context data.
The work function can use container_of() to work out the data.
For the cases where the container of the work_struct may go away the moment the
pending bit is cleared, it is made possible to defer the release of the
structure by deferring the clearing of the pending bit.
To make this work, an extra flag is introduced into the management side of the
work_struct. This governs auto-release of the structure upon execution.
Ordinarily, the work queue executor would release the work_struct for further
scheduling or deallocation by clearing the pending bit prior to jumping to the
work function. This means that, unless the driver makes some guarantee itself
that the work_struct won't go away, the work function may not access anything
else in the work_struct or its container lest they be deallocated.. This is a
problem if the auxiliary data is taken away (as done by the last patch).
However, if the pending bit is *not* cleared before jumping to the work
function, then the work function *may* access the work_struct and its container
with no problems. But then the work function must itself release the
work_struct by calling work_release().
In most cases, automatic release is fine, so this is the default. Special
initiators exist for the non-auto-release case (ending in _NAR).
Signed-Off-By: David Howells <dhowells@redhat.com>
This reverts commit 37605a6900.
Again.
This same bug has now been introduced twice: it was done earlier by
commit b8d35192c5, only to be reverted
last time in commit 72945b2b90.
We must NOT try to queue up notify handlers to another thread than the
normal ACPI execution thread, because the notifications on some systems
seem to just keep on accumulating until we run out of memory and/or
threads.
Keeping events within the one deferred execution thread automatically
throttles the events properly.
At least the Compaq N620c will lock up completely on the first thermal
event without this patch reverted.
Cc: David Brownell <david-b@pacbell.net>
Cc: Len Brown <len.brown@intel.com>
Cc: Alexey Starikovskiy <alexey.y.starikovskiy@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In addition to signalling button/lid events through /proc/acpi/event,
create separate input devices and report KEY_POWER, KEY_SLEEP and
SW_LID through input layer. Also remove unnecessary casts and variable
initializations, clean up formatting.
Sleep button may autorepeat but userspace will have to filter duplicate
sleep requests anyway (and discard unprocessed events right after
wakeup).
Unlike /proc/acpi/event interface input device corresponding to LID
switch reports true lid state instead of just a counter. SW_LID is
active when lid is closed.
The driver now depends on CONFIG_INPUT.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixing wrong description for acpi_gpe_sleep_prepare().
acpi_gpe_sleep_prepare() had only used on power off and was changed
to also used on entering some sleep state. However its description
isn't changed yet.
Signed-off-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix this warning :
drivers/acpi/events/evmisc.c: In function `acpi_ev_global_lock_handler':
drivers/acpi/events/evmisc.c:334: warning: unused variable `status'
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
http://bugzilla.kernel.org/show_bug.cgi?id=7303
Use a mutex instead of a spinlock for locking the
hotplug list because we need to call into the ACPI
subsystem which might sleep.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_get_pci_rootbridge_handle() walks the ACPI name space
searching for seg, bus and the PCI_ROOT_HID_STRING --
returning the handle as soon as if find the match.
But the current codes always parses through the whole namespace because
the user_function find_pci_rootbridge() returns status=AE_OK when it finds the match.
Make the find_pci_rootbridge() return AE_CTRL_TERMINATE when it finds the match.
This reduces the ACPI namespace walk for acpi_get_pci_rootbridge_handle().
Signed-off-by: Justin Chen <justin.chen@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix sparse warning:
drivers/acpi/ec.c:372:12: warning: function 'ec_transaction' with external linkage has definition
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Add support for the generic backlight interface below /sys/class/backlight.
Keep the procfs brightness handling for backward compatibility.
To achive this, add two generic functions get_lcd and set_lcd
to be used both by the procfs related and the sysfs related methods.
[apw@shadowen.org: backlight users need to select BACKLIGHT_CLASS_DEVICE]
Signed-off-by: Holger Macht <hmacht@suse.de>
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Add support for the generic backlight interface below /sys/class/backlight.
Keep the procfs brightness handling for backward compatibility.
[apw@shadowen.org: backlight users need to select BACKLIGHT_CLASS_DEVICE]
Signed-off-by: Holger Macht <hmacht@suse.de>
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Add support for the generic backlight interface below /sys/class/backlight.
The patch keeps the procfs brightness handling for backward compatibility.
Add two generic functions brightness_get and brightness_set
to be used both by the procfs related and the sysfs related methods.
[apw@shadowen.org: backlight users need to select BACKLIGHT_CLASS_DEVICE]
Signed-off-by: Holger Macht <hmacht@suse.de>
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
32bit vs 64 bit issues. sizeof(sizeof) and sizeof(pointer) is variable,
but we're trying to print it as unsigned int or u32.
Casts to unsigned long are used because type acpi_thread_id can be any one of
typedef u64 acpi_native_uint;
typedef u32 acpi_native_uint;
typedef u16 acpi_native_uint;
#define acpi_thread_id struct task_struct *
Signed-off-by: Martin J. Bligh <mbligh@google.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
I wrote a patch to avoid redundant memory hot-add call at boot time. This
was cause of strange fail message of memory hotplug like "ACPI: add_memory
failed". Memory is recognized by early boot code with EFI/E820.
But, if DSDT describes memory devices for them, then hot-add code is called
for already recognized memory, and it shows fail messages with -EEXIST.
So, sys admin will misunderstand this message as something wrong by it.
This patch avoids them by preventing redundant hot-add call until
completion of driver initialization.
[akpm@osdl.org: cleanups]
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I suppose this message seems quite useless except debugging. It just shows
"Hotplug Mem Device". System admin can't know anything by this message.
So, I would like to change it to KERN_DEBUG.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch breaks C-state discovery on my IBM IntelliStation Z30 because
the return value of acpi_processor_get_power_info_fadt is not assigned to
"result" in the case that acpi_processor_get_power_info_cst returns
-ENODEV. Thus, if ACPI provides C-state data via the FADT and not _CST (as
is the case on this machine), we incorrectly exit the function with -ENODEV
after reading the FADT. The attached patch sets the value of result so
that we don't exit early.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: "Pallipadi, Venkatesh" <venkatesh.pallipadi@intel.com>
Acked-by: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/acpi/processor_idle.c:1112: warning: 'smp_callback' defined but not used
Cc: Len Brown <lenb@kernel.org>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add ->resume method to the ACPI battery handler to check
if the battery state has changed during sleep.
If yes, update the ACPI internal data structures
for benefit of /proc/acpi/battery/.
Signed-off-by: Jiri Kosina <jikos@jikos.cz>
Cc: Stefan Seyfried <seife@suse.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
I could not get correct PCI Express bus number from the structure of
acpi_object_extra. I always get zero as bus number regardless of bus
location. I found that there is incorrect comparison with _HID (PNP0A08) in
acpi/events/evrgnini.c and PCI Express _BBN method always fail.
Therefore, we always get zero as PCI Express bus number.
http://bugzilla.kernel.org/show_bug.cgi?id=7145
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This reporting is useless (we errno anyway).
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
ICC complains about a "Pointless comparsion of unsigned interger with zero"
@ line 760 & 808 of asus_acpi.c
parse_arg() mentioned below returns -E but it's copied into unsigned variable...
Signed-off-by: Darren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix printk format warnings in drivers/acpi:
drivers/acpi/tables/tbget.c:326: warning: format '%X' expects type 'unsigned int', but argument 5 has type 'long unsigned int'
drivers/acpi/tables/tbrsdt.c:189: warning: format '%X' expects type 'unsigned int', but argument 5 has type 'long unsigned int'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The ACPI processor init functions should be marked as __cpuinit as they use
structures marked with __cpuinitdata.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_pci_link_set() allocates both with interrupts on
and with interrupts off (resume-time), so check interrupts
and decide on GFP_ATOMIC or GFP_KERNEL at run-time.
Signed-off-by: Jiri Kosina <jikos@jikos.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
device was set to null and used before set in a debug printk
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Len Brown <len.brown@intel.com>
On acquiring the ACPI global lock, if there were sleepers on the lock,
we used to use acpi_os_execute() to defer a thread which would signal
sleepers. Now just signal the semaphore directly.
http://bugzilla.kernel.org/show_bug.cgi?id=5534#c159
Signed-off-by: Len Brown <len.brown@intel.com>
Simplify acpi_hw_low_level_xxx() functions to inb() and outb().
Signed-off-by: Alexey Y. Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove unnecessary delay (50 ms) while reading data from EC in interrupt mode.
Signed-off-by: Alexey Y. Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Unify the following functions:
acpi_ec_poll_read()
acpi_ec_poll_write()
acpi_ec_poll_query()
acpi_ec_intr_read()
acpi_ec_intr_write()
acpi_ec_intr_query()
into:
acpi_ec_poll_transaction()
acpi_ec_intr_transaction()
These new functions take as arguments an ACPI EC command, a few bytes
to write to the EC data register and a buffer for a few bytes to read
from the EC data register. The old _read(), _write(), _query() are
just special cases of these functions.
Then unified the code in acpi_ec_poll_transaction() and
acpi_ec_intr_transaction() a little more. Both functions are now just
wrappers around the new acpi_ec_transaction_unlocked() function. The
latter contains the EC access logic, the two original
function now just do their special way of locking and call the the
new function for the actual work.
This saves a lot of very similar code. The primary reason for doing
this, however, is that my driver for MSI 270 laptops needs to issue
some non-standard EC commands in a safe way. Due to this I added a new
exported function similar to ec_write()/ec_write() which is called
ec_transaction() and is essentially just a wrapper around
acpi_ec_{poll,intr}_transaction().
Signed-off-by: Lennart Poettering <mzxreary@0pointer.de>
Acked-by: Luming Yu <luming.yu@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Intel processors starting with the Core Duo support
support processor native C-state using the MWAIT instruction.
Refer: Intel Architecture Software Developer's Manual
http://www.intel.com/design/Pentium4/manuals/253668.htm
Platform firmware exports the support for Native C-state to OS using
ACPI _PDC and _CST methods.
Refer: Intel Processor Vendor-Specific ACPI: Interface Specification
http://www.intel.com/technology/iapc/acpi/downloads/302223.htm
With Processor Native C-state, we use 'MWAIT' instruction on the processor
to enter different C-states (C1, C2, C3). We won't use the special IO
ports to enter C-state and no SMM mode etc required to enter C-state.
Overall this will mean better C-state support.
One major advantage of using MWAIT for all C-states is, with this and
"treat interrupt as break event" feature of MWAIT, we can now get accurate
timing for the time spent in C1, C2, .. states.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The brightness and volume features from ibm-acpi are stable.
The experimental flag is no longer needed.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Borislav Deianov <borislav@users.sourceforge.net>
Signed-off-by: Len Brown <len.brown@intel.com>
Add support for W3000 (W3V) and indirectly fixes an issue with kmilo under KDE
(it was triggering excessive LCD read error messages by querying asus_acpi
module) allowing people (I am probably the only one who tested this) with
W3000 to run kmilo.
Cc: Karol Kozimor <sziwan@hell.org.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
This is needed by at least the Mac Mini's, which (incorrectly) come back
from suspend with SCI_EN clear.
Thanks to Frdric Riss for hunting this down.
Acked-by: Frdric Riss <frederic.riss@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <len.brown@intel.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
Add infrastructure to track "maximum allowable latency" for power saving
policies.
The reason for adding this infrastructure is that power management in the
idle loop needs to make a tradeoff between latency and power savings
(deeper power save modes have a longer latency to running code again). The
code that today makes this tradeoff just does a rather simple algorithm;
however this is not good enough: There are devices and use cases where a
lower latency is required than that the higher power saving states provide.
An example would be audio playback, but another example is the ipw2100
wireless driver that right now has a very direct and ugly acpi hook to
disable some higher power states randomly when it gets certain types of
error.
The proposed solution is to have an interface where drivers can
* announce the maximum latency (in microseconds) that they can deal with
* modify this latency
* give up their constraint
and a function where the code that decides on power saving strategy can
query the current global desired maximum.
This patch has a user of each side: on the consumer side, ACPI is patched
to use this, on the producer side the ipw2100 driver is patched.
A generic maximum latency is also registered of 2 timer ticks (more and you
lose accurate time tracking after all).
While the existing users of the patch are x86 specific, the infrastructure
is not. I'd like to ask the arch maintainers of other architectures if the
infrastructure is generic enough for their use (assuming the architecture
has such a tradeoff as concept at all), and the sound/multimedia driver
owners to look at the driver facing API to see if this is something they
can use.
[akpm@osdl.org: cleanups]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jesse Barnes <jesse.barnes@intel.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In cases where the acpi memory-add event does not containe the pxm (node)
infomation allow the driver to look up node info based on the address. The
acpi_get_node call returns -1 if it can't decode the pxm info, this causes
add_memory to panic. acpi_get_node would have to decode the resource from the
handle (a lenghty proposition). This seems to be the cleanist point to
interject the hook.
[kamezawa.hiroyu@jp.fujitsu.com: build fixes]
[y-goto@jp.fujitsu.com: build fixes]
Signed-off-by: Keith Mannthey <kmannth@us.ibm.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* Rougly half of callers already do it by not checking return value
* Code in drivers/acpi/osl.c does the following to be sure:
(void)kmem_cache_destroy(cache);
* Those who check it printk something, however, slab_error already printed
the name of failed cache.
* XFS BUGs on failed kmem_cache_destroy which is not the decision
low-level filesystem driver should make. Converted to ignore.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
i2c: Constify i2c_algorithm declarations, part 2
Make struct i2c_algorithm declarations const in all i2c bus drivers
where it is possible.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While going through the code, I found out some memory leaks and potential
crashes in drivers/acpi/hotkey.c Please find the patch to fix them.
This patch does the following,
1. Fixes memory leaks in error paths of hotkey_write_config
2. Fixes freeing unallocated pointers in the error paths of hotkey_write_config
3. Uses a loop instead of linear searching for parsing the userspace
input in get_params
4. Uses array of char * instead of passing 4 pointer parameters
explicitly into the init_{poll_}hotkey_* static functions
Signed-off-by: Andrew Morton <akpm@osdl.org>
Acked-by: Luming Yu <luming.yu@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This is to remove noisy useless message at boot. The message is a ton of
"ACPI Exception (acpi_memory-0492): AE_ERROR, handle is no memory device"
In my emulation, number of memory devices are not so many (only 6), but,
this messages are displayed 114 times.
It is showed by acpi_memory_register_notify_handler() which is called by
acpi_walk_namespace().
acpi_walk_namespace() parses all of ACPI's namespace and execute
acpi_memory_register_notify_handler(). So, it is called for all of the
device which is defined in namespace. If the parsing device is not memory,
acpi_memhotplug ignores it due to "no match" and will parse next device.
This is normal route, not an exception.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix acpi_ac/battery boot with acpi=off
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
both of acpi_memory_enable_device() and acpi_memory_add_device() may evaluate
_CRS method.
We should avoid evaluate device's resource twice if we could get it
successfully in past.
Signed-off-by: KAMEZWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Keith Mannthey <kmannth@gmail.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
add_memory() does all necessary check to avoid collision. then, acpi layer
doesn't have to check region by itself.
(*) pfn_valid() just returns page struct is valid or not. It returns 0
if a section has been already added even is ioresource is not added.
ioresource collision check in mm/memory_hotplug.c can do more precise
collistion check.
added enabled bit check just for sanity check..
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Keith Mannthey <kmannth@gmail.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove uevent dock notifications. There are no consumers
of these events at present, and uevents are likely not the
correct way to send this type of event anyway.
Until I get some kind of idea if anyone in userspace cares
about dock events, I will just not send any.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ACPI_EXCEPTION() patch enabled a bunch of messages to print
even in the non-DEBUG kernel. Need to change a couple back,
and note that ACPI_EXCEPTION takes no \n, but ACPI_DEBUG_PRINT does.
No context for object [%p]\n
Device `[%s]' is not power manageable\n
Signed-off-by: Len Brown <len.brown@intel.com>
This effectively reverts commit b8d35192c5
by reverts acpi_os_queue_for_execution() to what it was before that,
except it changes the name to acpi_os_execute() to match ACPICA
20060512.
Signed-off-by: Len Brown <len.brown@intel.com>
[ The thread execution doesn't actually solve the bug it set out to
solve (see
http://bugzilla.kernel.org/show_bug.cgi?id=5534
for more details) because the new events can get caught behind the AML
semaphore or other serialization. And when that happens, the notify
threads keep on piling up until the system dies. ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Check and handle kset_register() and kobject_register() init errors.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: ACPI_DOCK: Initialize the atomic notifier list
ACPI: acpi_os_allocate() fixes
ACPI: SBS: fix initialization, sem2mutex
ACPI: add 'const' to several ACPI file_operations
ACPI: delete some defaults from ACPI Kconfig
ACPI: "Device `[%s]' is not power manageable" make message debug only
ACPI: ACPI_DOCK Kconfig
Revert "Revert "ACPI: dock driver""
ACPI: acpi_os_get_thread_id() returns current
ACPI: ACPICA 20060707
No need for video to be always in
No need for smart battery driver to be always in
Acked-by: Len Brown <len.brown@intel.com>
Cc: linux-acpi@vger.kernel.org
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Daniel Ritz <daniel.ritz-ml@swissonline.ch> says:
The acpi driver suspend/resume patches that went in recently caused a regression
on my box (toshiba tecra 8000 laptop): after resume from swsusp the fan turns on
keeping blowing cold air out of my notebook. before the patches, the fan was off
and would only make noise when required. it's the same thing described in
bugzilla.kernel.org #5000. the acpi suspend/resume patches or at least parts of
them originate in this bug. now the last patch in the report (attach id 8438)
actually fixes the problem - for me and the reporter. this is a trimmed down
version of that patch.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Len Brown <len.brown@intel.com>
Cc: Sanjoy Mahajan <sanjoy@mrao.cam.ac.uk>
Cc: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Replace acpi_in_resume with a more general hack
to check irqs_disabled() on any kmalloc() from ACPI.
While setting (system_state != SYSTEM_RUNNING) on resume
seemed more general, Andrew Morton preferred this approach.
http://bugzilla.kernel.org/show_bug.cgi?id=3469
Make acpi_os_allocate() into an inline function to
allow /proc/slab_allocators to work.
Delete some memset() that could fault on allocation failure.
Signed-off-by: Len Brown <len.brown@intel.com>
cm_sbs_sem is being downed (via acpi_ac_init->acpi_lock_ac_dir) before it is
initialised, with grave results.
- Make it a mutex
- Initialise it
- Make it static
- Clean other stuff up.
Thanks to Paul Drynoff <pauldrynoff@gmail.com> for reporting and testing.
Cc: Rich Townsend <rhdt@bartol.udel.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
No need for video to be always in
No need for ACPI dock driver to be always in
No need for smart battery driver to be always in
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
HOTPLUG_PCI_ACPI depends on ACPI_DOCK
ACPI_IBM_DOCK depends on ACPI_DOCK=n
ACPI_DOCK is EXPERIMENTAL, though that doesn't seem to mean much
Signed-off-by: Len Brown <len.brown@intel.com>
Linux mutexes and the debug code that that reference
acpi_os_get_thread_id() are happy with 0.
But the AML mutexes in exmutex.c expect a unique non-zero
number for each thread - as they track this thread_id
to permit the mutex re-entrancy defined by the ACPI spec.
http://bugzilla.kernel.org/show_bug.cgi?id=6687
Signed-off-by: Len Brown <len.brown@intel.com>
Added the ACPI_PACKED_POINTERS_NOT_SUPPORTED macro to
support C compilers that do not allow the initialization
of address pointers within packed structures - even though
the hardware itself may support misaligned transfers. Some
of the debug data structures are packed by default to
minimize size.
Added an error message for the case where
acpi_os_get_thread_id() returns zero. A non-zero value is
required by the core ACPICA code to ensure the proper
operation of AML mutexes and recursive control methods.
The DSDT is now the only ACPI table that determines whether
the AML interpreter is in 32-bit or 64-bit mode. Not really
a functional change, but the hooks for per-table 32/64
switching have been removed from the code. A clarification
to the ACPI specification is forthcoming in ACPI 3.0B.
Fixed a possible leak of an Owner ID in the error
path of tbinstal.c acpi_tb_init_table_descriptor() and
migrated all table OwnerID deletion to a single place in
acpi_tb_uninstall_table() to correct possible leaks when using
the acpi_tb_delete_tables_by_type() interface (with assistance
from Lance Ortiz.)
Fixed a problem with Serialized control methods where the
semaphore associated with the method could be over-signaled
after multiple method invocations.
Fixed two issues with the locking of the internal
namespace data structure. Both the Unload() operator and
acpi_unload_table() interface now lock the namespace during
the namespace deletion associated with the table unload
(with assistance from Linn Crosetto.)
Fixed problem reports (Valery Podrezov) integrated: -
Eliminate unnecessary memory allocation for CreateXxxxField
http://bugzilla.kernel.org/show_bug.cgi?id=5426
Fixed problem reports (Fiodor Suietov) integrated: -
Incomplete cleanup branches in AcpiTbGetTableRsdt (BZ 369)
- On Address Space handler deletion, needless deactivation
call (BZ 374) - AcpiRemoveAddressSpaceHandler: validate
Device handle parameter (BZ 375) - Possible memory leak,
Notify sub-objects of Processor, Power, ThermalZone (BZ
376) - AcpiRemoveAddressSpaceHandler: validate Handler
parameter (BZ 378) - Minimum Length of RSDT should be
validated (BZ 379) - AcpiRemoveNotifyHandler: return
AE_NOT_EXIST if Processor Obj has no Handler (BZ (380)
- AcpiUnloadTable: return AE_NOT_EXIST if no table of
specified type loaded (BZ 381)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This reverts commit a5e1b94008.
Adrian Bunk points out that it has build errors, and apparently no
maintenance. Throw it out.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Most batteries today are ACPI "Control Method" batteries,
but some models ship with the older "Smart Battery"
that requires this code.
Rich Townsend and Bruno Ducrot were the original authors.
Vladimir Lebedev updated to run on latest kernel.
http://bugzilla.kernel.org/show_bug.cgi?id=3734
Signed-off-by: Len Brown <len.brown@intel.com>
This patch switches back the display nodes for M6R and M6N -- this happened
a while ago when a patch was misapplied (only the in-tree version was
affected).
Signed-off-by: Karol Kozimor <sziwan@hell.org.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch switches back the display nodes for M6R and M6N -- this happened
a while ago when a patch was misapplied (only the in-tree version was
affected).
Signed-off-by: Karol Kozimor <sziwan@hell.org.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This small patch adds back WLED control for S1N models, this was
accidentally removed a while ago.
Signed-off-by: Karol Kozimor <sziwan@hell.org.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch reworks laptop model detection.
This addresses the Samsung P30 issue, where the INIT method would return no
object, but the implicit return in the AML interpreter would confuse the
driver. It also accounts for a newer batch of Asus models whose INIT
returns ACPI_TYPE_BUFFER instead of STRING.
The handling is now much leaner, if we get a buffer or a string, we check
against known values, in every other case we use a different path
(currently DSDT signatures). The bulk of this patch is separating the
string matching from asus_hotk_get_info() into a separate function.
This patch properly fixes http://bugme.osdl.org/show_bug.cgi?id=5067 and
http://bugme.osdl.org/show_bug.cgi?id=5092 and makes the driver fully
functional again with acpi=strict on all machines.
Signed-off-by: Karol Kozimor <sziwan@hell.org.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds support for Asus L5D and thus fixes
http://bugme.osdl.org/show_bug.cgi?id=4695
Signed-off-by: Karol Kozimor <sziwan@hell.org.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch creates a new file named "bluetooth" under /proc/acpi/asus/.
This file controls both the internal Bluetooth adapter's presence on the
USB bus and the associated LED.
echo 1 > /proc/acpi/asus/bluetooth to enable, 0 to disable.
Additionally, the patch add support for Asus W5A, the first model that uses
this feature.
Patch originally by Fernando A. P. Gomes.
Signed-off-by: Karol Kozimor <sziwan@hell.org.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds support for Asus A4G.
Originally by Giuseppe Rota.
Signed-off-by: Karol Kozimor <sziwan@hell.org.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds handling for front LED displays found on W1N and the like.
Additionally, W1N is given its own model_data instance.
Patch originally by Éric Burghard.
Signed-off-by: Karol Kozimor <sziwan@hell.org.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch updates the version string, copyright notices and does
whitespace cleanup (it looks weird, blame Lindent).
Signed-off-by: Karol Kozimor <sziwan@hell.org.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
- Use it instead of acpi_bus_get_device() in acpi_video_bus_notify()
and use the one from struct acpi_video_device in
acpi_video_device_notify().
Signed-off-by: Patrick Mochel <mochel@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
- Use it instead of acpi_bus_get_device() where we can..
Signed-off-by: Patrick Mochel <mochel@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
- Use it instead of acpi_bus_get_device() where we can..
Signed-off-by: Patrick Mochel <mochel@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
While trying to look for superfluous I/O accesses that can be optimized
away, I stumbled upon this ACPI sleep I/O access and couldn't figure out
why the hell this dummy op was necessary.
After more than one hour of internet research, I had collected a sufficient
number of documents (among those very old kernel versions) that finally
told me what this dummy read was about: STPCLK# doesn't get asserted in time
on (some) chipsets, which is why we need to have a dummy I/O read to delay
further instruction processing until the CPU is fully stopped.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Only if bus master activity is going on at the present, we should avoid
entering C3-type sleep, as it might be a faulty transition. As long as the
bm_activity bitmask was based on the number of calls to the ACPI idle
function, looking at previous moments made sense. Now, with it being based on
what happened this jiffy, looking at this jiffy should be sufficient.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Do not assume there was bus mastering activity if the idle handler didn't get
called, as there's only reason to not enter C3-type sleep if there is bus
master activity going on. Only for the "promotion" into C3-type sleep bus
mastering activity is taken into account, and there only current bus mastering
activity, and not pure guessing should lead to the decision on whether to
enter C3-type sleep or not.
Also, as bm_activity is a jiffy-based bitmask (bit 0: bus mastering activity
during this juffy, bit 31: bus mastering activity 31 jiffies ago), fix the
setting of bit 0, as it might be called multiple times within one jiffy.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Track the actual time spent in C-States (C2 upwards, we can't determine this
for C1), not only the number of invocations. This is especially useful for
dynamic ticks / "tickless systems", but is also of interest on normal systems,
as any interrupt activity leads to C-States being exited, not only the timer
interrupt.
The time is being measured in PM timer ticks, so an increase by one equals 279
nanoseconds.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Implemented a new acpi_spinlock type for the OSL lock
interfaces. This allows the type to be customized to
the host OS for improved efficiency (since a spinlock is
usually a very small object.)
Implemented support for "ignored" bits in the ACPI
registers. According to the ACPI specification, these
bits should be preserved when writing the registers via
a read/modify/write cycle. There are 3 bits preserved
in this manner: PM1_CONTROL[0] (SCI_EN), PM1_CONTROL[9],
and PM1_STATUS[11].
http://bugzilla.kernel.org/show_bug.cgi?id=3691
Implemented the initial deployment of new OSL mutex
interfaces. Since some host operating systems have
separate mutex and semaphore objects, this feature was
requested. The base code now uses mutexes (and the new
mutex interfaces) wherever a binary semaphore was used
previously. However, for the current release, the mutex
interfaces are defined as macros to map them to the
existing semaphore interfaces.
Fixed several problems with the support for the control
method SyncLevel parameter. The SyncLevel now works
according to the ACPI specification and in concert with the
Mutex SyncLevel parameter, since the current SyncLevel is
a property of the executing thread. Mutual exclusion for
control methods is now implemented with a mutex instead
of a semaphore.
Fixed three instances of the use of the C shift operator
in the bitfield support code (exfldio.c) to avoid the use
of a shift value larger than the target data width. The
behavior of C compilers is undefined in this case and can
cause unpredictable results, and therefore the case must
be detected and avoided. (Fiodor Suietov)
Added an info message whenever an SSDT or OEM table
is loaded dynamically via the Load() or LoadTable()
ASL operators. This should improve debugging capability
since it will show exactly what tables have been loaded
(beyond the tables present in the RSDT/XSDT.)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Create a driver which lives in the acpi subsystem to handle dock events.
This driver is not an "ACPI" driver, because acpi drivers require that the
object be present when the driver is loaded.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
This is to find node id from acpi's handle of memory_device in DSDT. _PXM for
the new node can be found by acpi_get_pxm() by using new memory's handle. So,
node id can be found by pxm_to_nid_map[].
This patch becomes simpler than v2 of node hot-add patch.
Because old add_memory() function doesn't have node id parameter.
So, kernel must find its handle by physical address via DSDT again.
But, v3 just give node id to add_memory() now.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change the name of old add_memory() to arch_add_memory. And use node id to
get pgdat for the node at NODE_DATA().
Note: Powerpc's old add_memory() is defined as __devinit. However,
add_memory() is usually called only after bootup.
I suppose it may be redundant. But, I'm not well known about powerpc.
So, I keep it. (But, __meminit is better at least.)
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When acpi_memory_device_init() is called at boottime to register struct
memory acpi_memory_device, acpi_bus_add() are called via
acpi_driver_attach().
But it also calls ops->start() function. It is called even if the memory
blocks are initialized at early boottime. In this case add_memory() return
-EEXIST, and the memory blocks becomes INVALID state even if it is normal.
This is patch to avoid calling add_memory() for already available memory.
[akpm@osdl.org: coding cleanups]
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: "Brown, Len" <len.brown@intel.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a patch to call add_memroy() when notify reaches for new node's add
event.
When new node is added, notify of ACPI reaches container device which means
the node.
Container device driver calls acpi_bus_scan() to find and add belonging
devices (which means cpu, memory and so on). Its function calls add and
start function of belonging devices's driver.
Howevever, current memory hotplug driver just register add function to
create sysfs file for its memory. But, acpi_memory_enable_device() is not
called because it is considered just the case that notify reaches memory
device directly. So, if notify reaches container device nothing can call
add_memory().
This is a patch to create start function which calls add_memory().
add_memory() can be called by this when notify reaches container device.
[akpm@osdl.org: coding cleanups]
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: "Brown, Len" <len.brown@intel.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Current acpi memory hotplug just looks into the first entry of resources in
_CRS. But, _CRS can contain plural resources. So, if _CRS contains plural
resoureces, acpi memory hot add cannot add all memory.
With this patch, acpi memory hotplug can deal with Memory Device, whose
_CRS contains plural resources.
Tested on ia64 memory hotplug test envrionment (not emulation, uses alpha
version firmware which supports dynamic reconfiguration of NUMA.)
Note: Microsoft's Windows Server 2003 requires big (>4G)resoureces to be
divided into small (<4G) resources. looks crazy, but not invalid.
(See http://www.microsoft.com/whdc/system/pnppwr/hotadd/hotaddmem.mspx)
For this reason, a firmware vendor who supports Windows writes plural
resources in a _CRS even if they are contiguous.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
print kobj name in this message.
lenb changed to use printk.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The ASL Acquire operator (17.5.1 in ACPI 3.0 spec) is allowed to time out
and return True without acquiring the semaphore. There's no indication in
the spec that this is an actual error, so this message should be
debug-only, as the message for successful acquisition is.
This used to be an ACPI_DEBUG_PRINT, but it was mis-classified as
ACPI_DB_ERROR rather than ACPI_DB_MUTEX, so it got swept up in Thomas'
recent patch to enable ACPI error messages even without CONFIG_ACPI_DEBUG.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
During some profiling I noticed that default_idle causes a lot of
memory traffic. I think that is caused by the atomic operations
to clear/set the polling flag in thread_info. There is actually
no reason to make this atomic - only the idle thread does it
to itself, other CPUs only read it. So I moved it into ti->status.
Converted i386/x86-64/ia64 for now because that was the easiest
way to fix ACPI which also manipulates these flags in its idle
function.
Cc: Nick Piggin <npiggin@novell.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As part of the i386 conversion to the generic timekeeping infrastructure, this
introduces a new tsc.c file. The code in this file replaces the TSC
initialization, management and access code currently in timer_tsc.c (which
will be removed) that we want to preserve.
The code also introduces the following functionality:
o tsc_khz: like cpu_khz but stores the TSC frequency on systems that do not
change TSC frequency w/ CPU frequency
o check/mark_tsc_unstable: accessor/modifier flag for TSC timekeeping
usability
o minor cleanups to calibration math.
This patch also includes a one line __cpuinitdata fix from Zwane Mwaikambo.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Treat HW coordination as independent CPUs.
This enables per-cpu monintoring of P-states
http://bugzilla.kernel.org/show_bug.cgi?id=5737
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (65 commits)
ACPI: suppress power button event on S3 resume
ACPI: resolve merge conflict between sem2mutex and processor_perflib.c
ACPI: use for_each_possible_cpu() instead of for_each_cpu()
ACPI: delete newly added debugging macros in processor_perflib.c
ACPI: UP build fix for bugzilla-5737
Enable P-state software coordination via _PDC
P-state software coordination for speedstep-centrino
P-state software coordination for acpi-cpufreq
P-state software coordination for ACPI core
ACPI: create acpi_thermal_resume()
ACPI: create acpi_fan_suspend()/acpi_fan_resume()
ACPI: pass pm_message_t from acpi_device_suspend() to root_suspend()
ACPI: create acpi_device_suspend()/acpi_device_resume()
ACPI: replace spin_lock_irq with mutex for ec poll mode
ACPI: Allow a WAN module enable/disable on a Thinkpad X60.
sem2mutex: acpi, acpi_link_lock
ACPI: delete unused acpi_bus_drivers_lock
sem2mutex: drivers/acpi/processor_perflib.c
ACPI add ia64 exports to build acpi_memhotplug as a module
ACPI: asus_acpi_init(): propagate correct return value
...
Manual resolve of conflicts in:
arch/i386/kernel/cpu/cpufreq/acpi-cpufreq.c
arch/i386/kernel/cpu/cpufreq/speedstep-centrino.c
include/acpi/processor.h
Consolidate the various arch-specific implementations of pxm_to_node() and
node_to_pxm() into a single generic version.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
According to the ACPI spec, it should be enabled on return from suspend,
but bugs happen. Apparently especially on the Apple Intel Macs.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
http://bugzilla.kernel.org/show_bug.cgi?id=6612
Note that this fix depends on a fix in ACPICA 20060608
to replace a semaphore with a spin-lock.
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
Acked-by: "Yu, Luming" <luming.yu@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Converted the locking mutex used for the ACPI hardware
to a spinlock. This change should eliminate all problems
caused by attempting to acquire a semaphore at interrupt
level, and it means that all ACPICA external interfaces
that directly access the ACPI hardware can be safely
called from interrupt level.
Fixed a regression introduced in 20060526 where the ACPI
device initialization could be prematurely aborted with
an AE_NOT_FOUND if a device did not have an optional
_INI method.
Fixed an IndexField issue where a write to the Data
Register should be limited in size to the AccessSize
(width) of the IndexField itself. (BZ 433, Fiodor Suietov)
Fixed problem reports (Valery Podrezov) integrated: - Allow
store of ThermalZone objects to Debug object.
http://bugzilla.kernel.org/show_bug.cgi?id=5369http://bugzilla.kernel.org/show_bug.cgi?id=5370
Fixed problem reports (Fiodor Suietov) integrated: -
acpi_get_table_header() doesn't handle multiple instances
correctly (BZ 364)
Removed four global mutexes that were obsolete and were
no longer being used.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Restructured, flattened, and simplified the internal
interfaces for namespace object evaluation - resulting
in smaller code, less CPU stack use, and fewer
interfaces. (With assistance from Mikhail Kouzmich)
Fixed a problem with the CopyObject operator where the
first parameter was not typed correctly for the parser,
interpreter, compiler, and disassembler. Caused various
errors and unexpected behavior.
Fixed a problem where a ShiftLeft or ShiftRight of
more than 64 bits produced incorrect results with some
C compilers. Since the behavior of C compilers when
the shift value is larger than the datatype width is
apparently not well defined, the interpreter now detects
this condition and simply returns zero as expected in all
such cases. (BZ 395)
Fixed problem reports (Valery Podrezov) integrated: -
Update String-to-Integer conversion to match ACPI 3.0A spec
http://bugzilla.kernel.org/show_bug.cgi?id=5329
Allow interpreter to handle nested method declarations
http://bugzilla.kernel.org/show_bug.cgi?id=5361
Fixed problem reports (Fiodor Suietov) integrated: -
acpi_terminate() doesn't free debug memory allocation
list objects (BZ 355) - After Core Subsystem
shutdown, acpi_subsystem_status() returns AE_OK (BZ 356) -
acpi_os_unmap_memory() for RSDP can be invoked inconsistently
(BZ 357) - Resource Manager should return AE_TYPE for
non-device objects (BZ 358) - Incomplete cleanup branch
in AcpiNsEvaluateRelative (BZ 359) - Use acpi_os_free()
instead of ACPI_FREE in acpi_rs_set_srs_method_data (BZ 360)
- Incomplete cleanup branch in acpi_ps_parse_aml (BZ 361) -
Incomplete cleanup branch in acpi_ds_delete_walk_state (BZ 362)
- acpi_get_table_header returns AE_NO_ACPI_TABLES until DSDT
is loaded (BZ 365) - Status of the Global Initialization
Handler call not used (BZ 366) - Incorrect object parameter
to Global Initialization Handler (BZ 367)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
http://bugzilla.kernel.org/show_bug.cgi?id=5534
Thanks to Peter Wainwright for isolating the issue.
Thanks to Andi Kleen and Bob Moore for feedback.
Thanks to Richard Mace and others for testing.
Updates by Konstantin Karasyov.
Signed-off-by: Konstantin Karasyov <konstantin.a.karasyov@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Replaced the acpi_os_queue_for_execution() with a new
interface named acpi_os_execute(). The major difference is
that the new interface does not have a Priority parameter,
this appeared to be useless and has been replaced by
a Type parameter. The Type tells the OS what type of
execution is being requested, such as global lock handler,
notify handler, GPE handler, etc. This allows the host
to queue and execute the request as appropriate for the
request type, possibly using different work queues and
different priorities for the various request types. This
enables fixes for multithreading deadlock problems such as
http://bugzilla.kernel.org/show_bug.cgi?id=5534
(Alexey Starikovskiy and Bob Moore)
Fixed a possible memory leak associated with the
support for the so-called "implicit return" ACPI
extension. Reported by FreeBSD (Fiodor Suietov)
http://bugzilla.kernel.org/show_bug.cgi?id=6514
Fixed a problem with the Load() operator where a table
load from an operation region could overwrite an internal
table buffer by up to 7 bytes and cause alignment faults
on IPF systems. (With assistance from Luming Yu)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Removed a device initialization optimization introduced in
20051216 where the _STA method was not run unless an _INI
was also present for the same device. This optimization
could cause problems because it could allow _INI methods
to be run within a not-present device subtree (If a
not-present device had no _INI, _STA would not be run,
the not-present status would not be discovered, and the
children of the device would be incorrectly traversed.)
Implemented a new _STA optimization where namespace
subtrees that do not contain _INI are identified and
ignored during device initialization. Selectively running
_STA can significantly improve boot time on large machines
(with assistance from Len Brown.)
Implemented support for the device initialization case
where the returned _STA flags indicate a device not-present
but functioning. In this case, _INI is not run, but the
device children are examined for presence, as per the
ACPI specification.
Implemented an additional change to the IndexField support
in order to conform to MS behavior. The value written to
the Index Register is not simply a byte offset, it is a
byte offset in units of the access width of the parent
Index Field. (Fiodor Suietov)
Defined and deployed a new OSL interface,
acpi_os_validate_address(). This interface is called during
the creation of all AML operation regions, and allows
the host OS to exert control over what addresses it will
allow the AML code to access. Operation Regions whose
addresses are disallowed will cause a runtime exception
when they are actually accessed (will not affect or abort
table loading.)
Defined and deployed a new OSL interface,
acpi_os_validate_interface(). This interface allows the host OS
to match the various "optional" interface/behavior strings
for the _OSI predefined control method as appropriate
(with assistance from Bjorn Helgaas.)
Restructured and corrected various problems in the
exception handling code paths within DsCallControlMethod
and DsTerminateControlMethod in dsmethod (with assistance
from Takayoshi Kochi.)
Modified the Linux source converter to ignore quoted string
literals while converting identifiers from mixed to lower
case. This will correct problems with the disassembler
and other areas where such strings must not be modified.
The ACPI_FUNCTION_* macros no longer require quotes around
the function name. This allows the Linux source converter
to convert the names, now that the converter ignores
quoted strings.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Implemented header file support for the following
additional ACPI tables: ASF!, BOOT, CPEP, DBGP, MCFG, SPCR,
SPMI, TCPA, and WDRT. With this support, all current and
known ACPI tables are now defined in the ACPICA headers and
are available for use by device drivers and other software.
Implemented support to allow tables that contain ACPI
names with invalid characters to be loaded. Previously,
this would cause the table load to fail, but since
there are several known cases of such tables on
existing machines, this change was made to enable
ACPI support for them. Also, this matches the
behavior of the Microsoft ACPI implementation.
https://bugzilla.novell.com/show_bug.cgi?id=147621
Fixed a couple regressions introduced during the memory
optimization in the 20060317 release. The namespace
node definition required additional reorganization and
an internal datatype that had been changed to 8-bit was
restored to 32-bit. (Valery Podrezov)
Fixed a problem where a null pointer passed to
acpi_ut_delete_generic_state() could be passed through
to acpi_os_release_object which is unexpected. Such
null pointers are now trapped and ignored, matching
the behavior of the previous implementation before the
deployment of acpi_os_release_object(). (Valery Podrezov,
Fiodor Suietov)
Fixed a memory mapping leak during the deletion of
a SystemMemory operation region where a cached memory
mapping was not deleted. This became a noticeable problem
for operation regions that are defined within frequently
used control methods. (Dana Meyers)
Reorganized the ACPI table header files into two main
files: one for the ACPI tables consumed by the ACPICA core,
and another for the miscellaneous ACPI tables that are
consumed by the drivers and other software. The various
FADT definitions were merged into one common section and
three different tables (ACPI 1.0, 1.0+, and 2.0)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Implemented the use of a cache object for all internal
namespace nodes. Since there are about 1000 static nodes
in a typical system, this will decrease memory use for
cache implementations that minimize per-allocation overhead
(such as a slab allocator.)
Removed the reference count mechanism for internal
namespace nodes, since it was deemed unnecessary. This
reduces the size of each namespace node by about 5%-10%
on all platforms. Nodes are now 20 bytes for the 32-bit
case, and 32 bytes for the 64-bit case.
Optimized several internal data structures to reduce
object size on 64-bit platforms by packing data within
the 64-bit alignment. This includes the frequently used
ACPI_OPERAND_OBJECT, of which there can be ~1000 static
instances corresponding to the namespace objects.
Added two new strings for the predefined _OSI method:
"Windows 2001.1 SP1" and "Windows 2006".
Split the allocation tracking mechanism out to a separate
file, from utalloc.c to uttrack.c. This mechanism appears
to be only useful for application-level code. Kernels may
wish to not include uttrack.c in distributions.
Removed all remnants of the obsolete ACPI_REPORT_* macros
and the associated code. (These macros have been replaced
by the ACPI_ERROR and ACPI_WARNING macros.)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
From: Andrew Morton <akpm@osdl.org>
Work around the oops reported in
http://bugzilla.kernel.org/show_bug.cgi?id=6478.
Thanks to Ralf Hildebrandt <ralf.hildebrandt@charite.de> for testing and
reporting.
Acked-by: Dave Jones <davej@codemonkey.org.uk>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The WAN (Sierra Wireless EV-DO) module is very similar to the
Bluetooth module. It appears on the USB bus when enabled. It can be
controlled via hot key, or directly via ACPI. This change enables
direct control via ACPI.
I have tested it on my Lenovo Thinkpad X60; I guess it will probably
work on other Thinkpad models which come with this module installed.
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Ack'd by: Borislav Deianov <borislav@users.sf.net>
Signed-off-by: Len Brown <len.brown@intel.com>
in case we want to decode it for future use in acpi_op_suspend(..., state)
also, inline new 1-liner static function
http://bugzilla.kernel.org/show_bug.cgi?id=5000
Signed-off-by: Len Brown <len.brown@intel.com>
updated and tested by Konstantin Karasyov
http://bugzilla.kernel.org/show_bug.cgi?id=5000
Signed-off-by: Patrick Mochel <patrick.mochel@intel.com>
Signed-off-by: Konstantin Karasyov <konstantin.karasyov @intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_video_bus_get_one_device() and other functions in driver/acpi/video.c do
not release allocated memory on remove and on the error path.
Signed-off-by: "Yu, Luming" <luming.yu@intel.com>
Signed-off-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
make pm_idle_save, nocst and bm_history __read_mostly
remove initializer from static 'first_run'.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Nobody looks at the return value, and this brings it into line with
pci_unregister_driver(), etc. Also removed validation of the driver
pointer passed in to register and unregister. More consistent, and we'll
find bugs faster if we fault rather than returning an error that's ignored.
Also makes internal functions acpi_device_unregister() and
acpi_driver_detach() void, since nobody uses their returns either.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
for_each_cpu() actually iterates across all possible CPUs. We've had mistakes
in the past where people were using for_each_cpu() where they should have been
iterating across only online or present CPUs. This is inefficient and
possibly buggy.
We're renaming for_each_cpu() to for_each_possible_cpu() to avoid this in the
future.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Memory hotadd doesn't need SPARSEMEM, but can be handled by just preallocating
mem_maps. This only needs some untangling of ifdefs to enable the necessary
code even without SPARSEMEM.
Originally from Keith Mannthey, hacked by AK.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Internal BIOS names like these should be exposed
to the user as little as possible:
ACPI wakeup devices: C069 C0CE C1D1 C0DE C1D4
Eventually, the "wakeup" property of a device should be exported via the
device tree, not by a printk of an internal BIOS name. For the hard-core,
these are still available in /proc/acpi/wakeup_devices, just not
printed to dmesg.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_eject_store() didn't trim processors, causing subsequent
hot-add to fail.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
On some boxes ecdt uid may be equal to 0, so do not test for uids equality,
so that fake handler will be unconditionally removed to allow loading the
real one.
See http://bugzilla.kernel.org/show_bug.cgi?id=6111
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Luming Yu <luming.yu@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Local apic entries are only 8 bits, but it seemed to not be caught with u8
return value result in the check
cpu_index >= NR_CPUS becomming always false.
drivers/acpi/processor_core.c: In function `acpi_processor_get_info':
drivers/acpi/processor_core.c:483: warning: comparison is always false due to limited range of data type
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Kenji Kaneshige <kaneshige.kenji@soft.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Even though the devices claimed by asus_acpi.c can not be hot-plugged, the
driver registration infrastructure allows the .add() and .remove() methods to
be called at any time while the driver is registered. So remove __init and
__exit from them.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Address space descriptors contain _MIN, _MAX, and _LEN. _MIN and _MAX are
the bounds within which the region can be moved (this is clarified in Table
6-38 of the ACPI 3.0 spec). We should use _LEN to determine the size of
the region, not _MAX - _MIN + 1.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
No functional changes; just remove leftover, unused "buffer" and simplify
control flow (no need to remember error values and goto the end, when we can
simply return the value directly).
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove the assumption that acpi_bus_register_driver() returns the number of
devices claimed. Returning the count is unreliable because devices may be
hot-plugged in the future (admittedly not applicable for this driver).
Since the hardware for this driver is not hot-pluggable, determine whether the
hardware is present by noticing calls to the .add() method. It would be
better to probe the ACPI namespace for the ASUS HIDs, and load the driver only
when we find one, but ACPI doesn't support that yet.
I don't have an ASUS laptop to test on, but on my HP dl360, it does report the
appropriate error when attempting to load the module:
$ sudo insmod drivers/acpi/asus_acpi.ko
insmod: error inserting 'drivers/acpi/asus_acpi.ko': -1 No such device
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_bus_register_driver() should not return the number of devices claimed.
We're not asking to find devices, we're making a driver available to devices,
including hot-pluggable devices that may appear in the future.
I audited all callers of acpi_bus_register_driver(), and except asus_acpi.c
and sonypi.c (fixed in previous patches), all either ignore the return value
or test only for failure (<0).
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Add "ACPI" to motherboard resource allocation names, so people have a clue
about where to look. And remove some trailing spaces.
Changes these /proc/iomem entries from this:
ff5c1004-ff5c1007 : PM_TMR
ff5c1008-ff5c100b : PM1a_EVT_BLK
ff5c100c-ff5c100d : PM1a_CNT_BLK
ff5c1010-ff5c1013 : GPE0_BLK
ff5c1014-ff5c1017 : GPE1_BLK
to this:
ff5c1004-ff5c1007 : ACPI PM_TMR
ff5c1008-ff5c100b : ACPI PM1a_EVT_BLK
ff5c100c-ff5c100d : ACPI PM1a_CNT_BLK
ff5c1010-ff5c1013 : ACPI GPE0_BLK
ff5c1014-ff5c1017 : ACPI GPE1_BLK
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI supports fixed hardware (PM_TMR, GPE blocks, etc) in either I/O port
or MMIO space, but used to always request the regions from I/O space
because it didn't check the address_space_id.
Sample ACPI fixed hardware in MMIO space (HP rx2600), was incorrectly
reported in /proc/ioports, now reported in /proc/iomem:
ff5c1004-ff5c1007 : PM_TMR
ff5c1008-ff5c100b : PM1a_EVT_BLK
ff5c100c-ff5c100d : PM1a_CNT_BLK
ff5c1010-ff5c1013 : GPE0_BLK
ff5c1014-ff5c1017 : GPE1_BLK
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Otherwise, illegal configurations like X86_VOYAGER=y, PCI=y are
possible.
This patch also fixes the options select'ing ACPI to also select PCI.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Tagged all external interfaces to the subsystem with the
new ACPI_EXPORT_SYMBOL macro. This macro can be defined
as necessary to assist kernel integration. For Linux,
the macro resolves to the EXPORT_SYMBOL macro. The default
definition is NULL.
Added the ACPI_THREAD_ID type for the return value from
acpi_os_get_thread_id(). This allows the host to define this
as necessary to simplify kernel integration. The default
definition is ACPI_NATIVE_UINT.
Valery Podrezov fixed two interpreter problems related
to error processing, the deletion of objects, and placing
invalid pointers onto the internal operator result stack.
http://bugzilla.kernel.org/show_bug.cgi?id=6028http://bugzilla.kernel.org/show_bug.cgi?id=6151
Increased the reference count threshold where a warning is
emitted for large reference counts in order to eliminate
unnecessary warnings on systems with large namespaces
(especially 64-bit.) Increased the value from 0x400
to 0x800.
Due to universal disagreement as to the meaning of the
'c' in the calloc() function, the ACPI_MEM_CALLOCATE
macro has been renamed to ACPI_ALLOCATE_ZEROED so that the
purpose of the interface is 'clear'. ACPI_MEM_ALLOCATE and
ACPI_MEM_FREE are renamed to ACPI_ALLOCATE and ACPI_FREE.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Implemented a change to the IndexField support to match
the behavior of the Microsoft AML interpreter. The value
written to the Index register is now a byte offset,
no longer an index based upon the width of the Data
register. This should fix IndexField problems seen on
some machines where the Data register is not exactly one
byte wide. The ACPI specification will be clarified on
this point.
Fixed a problem where several resource descriptor
types could overrun the internal descriptor buffer due
to size miscalculation: VendorShort, VendorLong, and
Interrupt. This was noticed on IA64 machines, but could
affect all platforms.
Fixed a problem where individual resource descriptors were
misaligned within the internal buffer, causing alignment
faults on IA64 platforms.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The boot cmdline is parsed in parse_early_param() and
parse_args(,unknown_bootoption).
And __setup() is used in obsolete_checksetup().
start_kernel()
-> parse_args()
-> unknown_bootoption()
-> obsolete_checksetup()
If __setup()'s callback (->setup_func()) returns 1 in
obsolete_checksetup(), obsolete_checksetup() thinks a parameter was
handled.
If ->setup_func() returns 0, obsolete_checksetup() tries other
->setup_func(). If all ->setup_func() that matched a parameter returns 0,
a parameter is seted to argv_init[].
Then, when runing /sbin/init or init=app, argv_init[] is passed to the app.
If the app doesn't ignore those arguments, it will warning and exit.
This patch fixes a wrong usage of it, however fixes obvious one only.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removed a couple of extraneous ACPI_ERROR messages that
appeared during normal execution. These became apparent
after the conversion from ACPI_DEBUG_PRINT.
Fixed a problem where the CreateField operator could hang
if the BitIndex or NumBits parameter referred to a named
object. From Valery Podrezov.
http://bugzilla.kernel.org/show_bug.cgi?id=5359
Fixed a problem where a DeRefOf operation on a buffer
object incorrectly failed with an exception. This also
fixes a couple of related RefOf and DeRefOf issues.
From Valery Podrezov.
http://bugzilla.kernel.org/show_bug.cgi?id=5360http://bugzilla.kernel.org/show_bug.cgi?id=5387http://bugzilla.kernel.org/show_bug.cgi?id=5392
Fixed a problem where the AE_BUFFER_LIMIT exception was
returned instead of AE_STRING_LIMIT on an out-of-bounds
Index() operation. From Valery Podrezov.
http://bugzilla.kernel.org/show_bug.cgi?id=5480
Implemented a memory cleanup at the end of the execution
of each iteration of an AML While() loop, preventing the
accumulation of outstanding objects. From Valery Podrezov.
http://bugzilla.kernel.org/show_bug.cgi?id=5427
Eliminated a chunk of duplicate code in the object
resolution code. From Valery Podrezov.
http://bugzilla.kernel.org/show_bug.cgi?id=5336
Fixed several warnings during the 64-bit code generation.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The Coverity checker spotted this bug in
acpi_video_device_lcd_query_levels().
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Len Brown <len.brown@intel.com>
ia64 ioremap is now smart enough to use the correct memory attributes, so
remove the EFI checks from osl.c.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Cc: "Tolentino, Matthew E" <matthew.e.tolentino@intel.com>
Cc: "Brown, Len" <len.brown@intel.com>
Cc: Andi Kleen <ak@muc.de>
Acked-by: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here's a patch that fixes EFI boot for x86 on 2.6.16-rc5-mm3. The
off-by-one is admittedly my fault, but the other two fix up the rest.
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Cc: "Tolentino, Matthew E" <matthew.e.tolentino@intel.com>
Cc: "Brown, Len" <len.brown@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Almost all users of the table addresses from the EFI system table want
physical addresses. So rather than doing the pa->va->pa conversion, just keep
physical addresses in struct efi.
This fixes a DMI bug: the efi structure contained the physical SMBIOS address
on x86 but the virtual address on ia64, so dmi_scan_machine() used ioremap()
on a virtual address on ia64.
This is essentially the same as an earlier patch by Matt Tolentino:
http://marc.theaimsgroup.com/?l=linux-kernel&m=112130292316281&w=2
except that this changes all table addresses, not just ACPI addresses.
Matt's original patch was backed out because it caused MCAs on HP sx1000
systems. That problem is resolved by the ioremap() attribute checking added
for ia64.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Cc: "Tolentino, Matthew E" <matthew.e.tolentino@intel.com>
Cc: "Brown, Len" <len.brown@intel.com>
Cc: Andi Kleen <ak@muc.de>
Acked-by: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Broken earlier by me by a x86-64 patch.
The code was optimized away, but the compiler still complained about an
undeclared function.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Move the core parser into dmi_scan.c. It can be useful for other
subsystems too.
- Differentiate between field doesn't exist and field is 0 or
unparseable. The first case is likely an old BIOS with broken ACPI,
the later is likely a slightly buggy BIOS where someone forget to
edit the date. Don't blacklist in the later case.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove dock station support from ibm_acpi by default. This support has
been put into acpiphp instead. Allow ibm_acpi to continue to provide
docking station support via config option for laptops/docking stations
that are not supported by acpiphp.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Export the acpi_bus_trim function so that the pci hotplug driver can
use it.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ACPI is initialized very early on x86-64, before the DMI code is
initialized. This means it would often discover a 0 year and then turn
off ACPI because it thought the BIOS was too old. Some systems don't
boot without ACPI so this was a problem.
I have a full fix by adding new very early DMI detection, but it needs
more testing before it can be merged. For 2.6.16 let's just turn the
check off. It never made much sense anyways because there are no x86-64
systems older than 2002 or so and they generally all have working ACPI.
Cc: len.brown@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This makes x86-64 use the common X86_PM_TIMER Kconfig entry in drivers/acpi
And since PM timer is needed for correct timing on a lot of systems
now (e.g. AMD dual cores) and we often get bug reports from people
who forgot to set it make it depend on CONFIG_EMBEDDED. x86-64 had
this change before and it's a good thing.
I also fixed the description slightly to make this more clear.
Cc: len.brown@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
acpi_rs_get_list_length() needs to account for all the vendor-defined data
bytes. Failing to include these causes buffers to be sized too small,
which causes slab corruption when we later convert AML to resources and run
off the end of the buffer.
This causes slab corruption on machines that use ACPI vendor-defined
resources. All HP ia64 machines do, and I'm told that some NEC machines
may as well.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
attached patch is 2 more cases i found via running the reference_init.pl
script. These were easy to spot just knowing the file names. There is
one another about init/main.c that i cant exactly zero in. (partly
because i dont know how to interpret the data thats spewed out of the tool).
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bug in apic timer removal on C3 patch. We should switch to IPI from APIC timer
only when C3 state is valid.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Implemented support in the Resource Manager to allow
unresolved namestring references within resource package
objects for the _PRT method. This support is in addition
to the previously implemented unresolved reference
support within the AML parser. If the interpreter slack
mode is enabled (true on Linux unless acpi=strict),
these unresolved references will be passed through
to the caller as a NULL package entry.
http://bugzilla.kernel.org/show_bug.cgi?id=5741
Implemented and deployed new macros and functions for
error and warning messages across the subsystem. These
macros are simpler and generate less code than their
predecessors. The new macros ACPI_ERROR, ACPI_EXCEPTION,
ACPI_WARNING, and ACPI_INFO replace the ACPI_REPORT_*
macros.
Implemented the acpi_cpu_flags type to simplify host OS
integration of the Acquire/Release Lock OSL interfaces.
Suggested by Steven Rostedt and Andrew Morton.
Fixed a problem where Alias ASL operators are sometimes
not correctly resolved. causing AE_AML_INTERNAL
http://bugzilla.kernel.org/show_bug.cgi?id=5189http://bugzilla.kernel.org/show_bug.cgi?id=5674
Fixed several problems with the implementation of the
ConcatenateResTemplate ASL operator. As per the ACPI
specification, zero length buffers are now treated as a
single EndTag. One-length buffers always cause a fatal
exception. Non-zero length buffers that do not end with
a full 2-byte EndTag cause a fatal exception.
Fixed a possible structure overwrite in the
AcpiGetObjectInfo external interface. (With assistance
from Thomas Renninger)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
In the case where a (broken) BIOS gives us a blank _CRS for
a PCI Interrupt Link Device, the acpi_walk_resources()
will not terminate, but will then give the callback
the resource end tag. Ignore the end tag.
Signed-off-by: Len Brown <len.brown@intel.com>
Kristen Carlson Accardi