XFRM expects xfrm_dst->u.next to be same pointer as dst->next, which
was broken by the dst_entry reordering in commit 1e19e02c~, causing
an oops in xfrm_bundle_ok when walking the bundle upwards.
Kill xfrm_dst->u.next and change the only user to use dst->next instead.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows other in-kernel functions to do SAD lookups.
The only known user at the moment is pktgen.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
My IPsec MTU optimization patch introduced a regression in MTU calculation
for non-ESP SAs, the SA's header_len needs to be subtracted from the MTU if
the transform doesn't provide a ->get_mtu() function.
Reported-and-tested-by: Marco Berizzi <pupilla@hotmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we check for permission before deleting entries from SAD and
SPD, (see security_xfrm_policy_delete() security_xfrm_state_delete())
However we are not checking for authorization when flushing the SPD and
the SAD completely. It was perhaps missed in the original security hooks
patch.
This patch adds a security check when flushing entries from the SAD and
SPD. It runs the entire database and checks each entry for a denial.
If the process attempting the flush is unable to remove all of the
entries a denial is logged the the flush function returns an error
without removing anything.
This is particularly useful when a process may need to create or delete
its own xfrm entries used for things like labeled networking but that
same process should not be able to delete other entries or flush the
entire database.
Signed-off-by: Joy Latten<latten@austin.ibm.com>
Signed-off-by: Eric Paris <eparis@parisplace.org>
Signed-off-by: James Morris <jmorris@namei.org>
The current IPSEC rule resolution behavior we have does not work for a
lot of people, even though technically it's an improvement from the
-EAGAIN buisness we had before.
Right now we'll block until the key manager resolves the route. That
works for simple cases, but many folks would rather packets get
silently dropped until the key manager resolves the IPSEC rules.
We can't tell these folks to "set the socket non-blocking" because
they don't have control over the non-block setting of things like the
sockets used to resolve DNS deep inside of the resolver libraries in
libc.
With that in mind I coded up the patch below with some help from
Herbert Xu which provides packet-drop behavior during larval state
resolution, controllable via sysctl and off by default.
This lays the framework to either:
1) Make this default at some point or...
2) Move this logic into xfrm{4,6}_policy.c and implement the
ARP-like resolution queue we've all been dreaming of.
The idea would be to queue packets to the policy, then
once the larval state is resolved by the key manager we
re-resolve the route and push the packets out. The
packets would timeout if the rule didn't get resolved
in a certain amount of time.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds some casts to shut up the warnings introduced by my
last patch that added a common interator function for xfrm algorightms.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a natural extension of the changeset
[XFRM]: Probe selected algorithm only.
which only removed the probe call for xfrm_user. This patch does exactly
the same thing for af_key. In other words, we load the algorithm requested
by the user rather than everything when adding xfrm states in af_key.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multi-page allocations are always likely to fail. Since such failures
are expected and non-critical in xfrm_hash_alloc, we shouldn't warn about
them.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function xfrm_policy_byid takes a dir argument but finds the policy
using the index instead. We only use the dir argument to update the
policy count for that direction. Since the user can supply any value
for dir, this can corrupt our policy count.
I know this is the problem because a few days ago I was deleting
policies by hand using indicies and accidentally typed in the wrong
direction. It still deleted the policy and at the time I thought
that was cool. In retrospect it isn't such a good idea :)
I decided against letting it delete the policy anyway just in case
we ever remove the connection between indicies and direction.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aggregate the SPD info TLVs.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aggregate the SAD info TLVs.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
On MIPv6 usage, XFRM sub policy is enabled.
When main (IPsec) and sub (MIPv6) policy selectors have the same
address set but different upper layer information (i.e. protocol
number and its ports or type/code), multiple bundle should be created.
However, currently we have issue to use the same bundle created for
the first time with all flows covered by the case.
It is useful for the bundle to have the upper layer information
to be restructured correctly if it does not match with the flow.
1. Bundle was created by two policies
Selector from another policy is added to xfrm_dst.
If the flow does not match the selector, it goes to slow path to
restructure new bundle by single policy.
2. Bundle was created by one policy
Flow cache is added to xfrm_dst as originated one. If the flow does
not match the cache, it goes to slow path to try searching another
policy.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch you can use iproute2 in user space to efficiently see
how many policies exist in different directions.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts eefa390628
The simplification made in that change works with the assumption that
the 'offset' parameter to these functions is always positive or zero,
which is not true. It can be and often is negative in order to access
SKB header values in front of skb->data.
Signed-off-by: David S. Miller <davem@davemloft.net>
This brings the SAD info in sync with net-2.6.22/net-2.6
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
I noticed recently that, in skb_checksum(), "offset" and "start" are
essentially the same thing and have the same value throughout the
function, despite being computed differently. Using a single variable
allows some cleanups and makes the skb_checksum() function smaller,
more readable, and presumably marginally faster.
We appear to have many other "sk_buff walker" functions built on the
exact same model, so the cleanup applies to them, too. Here is a list
of the functions I found to be affected:
net/appletalk/ddp.c:atalk_sum_skb()
net/core/datagram.c:skb_copy_datagram_iovec()
net/core/datagram.c:skb_copy_and_csum_datagram()
net/core/skbuff.c:skb_copy_bits()
net/core/skbuff.c:skb_store_bits()
net/core/skbuff.c:skb_checksum()
net/core/skbuff.c:skb_copy_and_csum_bit()
net/core/user_dma.c:dma_skb_copy_datagram_iovec()
net/xfrm/xfrm_algo.c:skb_icv_walk()
net/xfrm/xfrm_algo.c:skb_to_sgvec()
OTOH, I admit I'm a bit surprised, the cleanup is rather obvious so I'm
really wondering if I am missing something. Can anyone please comment
on this?
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
On a system with a lot of SAs, counting SAD entries chews useful
CPU time since you need to dump the whole SAD to user space;
i.e something like ip xfrm state ls | grep -i src | wc -l
I have seen taking literally minutes on a 40K SAs when the system
is swapping.
With this patch, some of the SAD info (that was already being tracked)
is exposed to user space. i.e you do:
ip xfrm state count
And you get the count; you can also pass -s to the command line and
get the hash info.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spring cleaning time...
There seems to be a lot of places in the network code that have
extra bogus semicolons after conditionals. Most commonly is a
bogus semicolon after: switch() { }
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch cb_lock to mutex and allow netlink kernel users to override it
with a subsystem specific mutex for consistent locking in dump callbacks.
All netlink_dump_start users have been audited not to rely on any
side-effects of the previously used spinlock.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the probing based MTU estimation, which usually takes 2-3 iterations
to find a fitting value and may underestimate the MTU, by an exact calculation.
Also fix underestimation of the XFRM trailer_len, which causes unnecessary
reallocations.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move generic skbuff stuff from XFRM code to generic code so that
AF_RXRPC can use it too.
The kdoc comments I've attached to the functions needs to be checked
by whoever wrote them as I had to make some guesses about the workings
of these functions.
Signed-off-By: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all users of netlink_dump_start() use netlink_run_queue()
to process the receive queue, it is possible to return -EINTR from
netlink_dump_start() directly, therefore simplying the callers.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error pointer argument in netlink message handlers is used
to signal the special case where processing has to be interrupted
because a dump was started but no error happened. Instead it is
simpler and more clear to return -EINTR and have netlink_run_queue()
deal with getting the queue right.
nfnetlink passed on this error pointer to its subsystem handlers
but only uses it to signal the start of a netlink dump. Therefore
it can be removed there as well.
This patch also cleans up the error handling in the affected
message handlers to be consistent since it had to be touched anyway.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes netlink_rcv_skb() to skip netlink controll messages and don't
pass them on to the message handler.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
netlink_rcv_skb() is changed to skip messages which don't have the
NLM_F_REQUEST bit to avoid every netlink family having to perform this
check on their own.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
So that it is also an offset from skb->head, reduces its size from 8 to 4 bytes
on 64bit architectures, allowing us to combine the 4 bytes hole left by the
layer headers conversion, reducing struct sk_buff size to 256 bytes, i.e. 4
64byte cachelines, and since the sk_buff slab cache is SLAB_HWCACHE_ALIGN...
:-)
Many calculations that previously required that skb->{transport,network,
mac}_header be first converted to a pointer now can be done directly, being
meaningful as offsets or pointers.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the places where we need a pointer to the transport header, it is
still legal to touch skb->h.raw directly if just adding to,
subtracting from or setting it to another layer header.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Where appropriate, convert references to xtime.tv_sec to the
get_seconds() helper function.
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending a security context of 50+ characters in an ACQUIRE
message, following kernel panic occurred.
kernel BUG in xfrm_send_acquire at net/xfrm/xfrm_user.c:1781!
cpu 0x3: Vector: 700 (Program Check) at [c0000000421bb2e0]
pc: c00000000033b074: .xfrm_send_acquire+0x240/0x2c8
lr: c00000000033b014: .xfrm_send_acquire+0x1e0/0x2c8
sp: c0000000421bb560
msr: 8000000000029032
current = 0xc00000000fce8f00
paca = 0xc000000000464b00
pid = 2303, comm = ping
kernel BUG in xfrm_send_acquire at net/xfrm/xfrm_user.c:1781!
enter ? for help
3:mon> t
[c0000000421bb650] c00000000033538c .km_query+0x6c/0xec
[c0000000421bb6f0] c000000000337374 .xfrm_state_find+0x7f4/0xb88
[c0000000421bb7f0] c000000000332350 .xfrm_tmpl_resolve+0xc4/0x21c
[c0000000421bb8d0] c0000000003326e8 .xfrm_lookup+0x1a0/0x5b0
[c0000000421bba00] c0000000002e6ea0 .ip_route_output_flow+0x88/0xb4
[c0000000421bbaa0] c0000000003106d8 .ip4_datagram_connect+0x218/0x374
[c0000000421bbbd0] c00000000031bc00 .inet_dgram_connect+0xac/0xd4
[c0000000421bbc60] c0000000002b11ac .sys_connect+0xd8/0x120
[c0000000421bbd90] c0000000002d38d0 .compat_sys_socketcall+0xdc/0x214
[c0000000421bbe30] c00000000000869c syscall_exit+0x0/0x40
--- Exception: c00 (System Call) at 0000000007f0ca9c
SP (fc0ef8f0) is in userspace
We are using size of security context from xfrm_policy to determine
how much space to alloc skb and then putting security context from
xfrm_state into skb. Should have been using size of security context
from xfrm_state to alloc skb. Following fix does that
Signed-off-by: Joy Latten <latten@austin.ibm.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until this point we've accepted replay window settings greater than
32 but our bit mask can only accomodate 32 packets. Thus any packet
with a sequence number within the window but outside the bit mask would
be accepted.
This patch causes those packets to be rejected instead.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turning up the warnings on gcc makes it emit warnings
about the placement of 'inline' in function declarations.
Here's everything that was under net/
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a space between printing of the src and dst ipv6 addresses.
Otherwise, audit or other test tools may fail to process the audit
record properly because they cannot find the dst address.
Signed-off-by: Joy Latten <latten@austin.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I noticed that in xfrm_state_add we look for the larval SA in a few
places without checking for protocol match. So when using both
AH and ESP, whichever one gets added first, deletes the larval SA.
It seems AH always gets added first and ESP is always the larval
SA's protocol since the xfrm->tmpl has it first. Thus causing the
additional km_query()
Adding the check eliminates accidental double SA creation.
Signed-off-by: Joy Latten <latten@austin.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inside pfkey_delete and xfrm_del_sa the audit hooks were not called if
there was any permission/security failures in attempting to do the del
operation (such as permission denied from security_xfrm_state_delete).
This patch moves the audit hook to the exit path such that all failures
(and successes) will actually get audited.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Venkat Yekkirala <vyekkirala@trustedcs.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The security hooks to check permissions to remove an xfrm_policy were
actually done after the policy was removed. Since the unlinking and
deletion are done in xfrm_policy_by* functions this moves the hooks
inside those 2 functions. There we have all the information needed to
do the security check and it can be done before the deletion. Since
auditing requires the result of that security check err has to be passed
back and forth from the xfrm_policy_by* functions.
This patch also fixes a bug where a deletion that failed the security
check could cause improper accounting on the xfrm_policy
(xfrm_get_policy didn't have a put on the exit path for the hold taken
by xfrm_policy_by*)
It also fixes the return code when no policy is found in
xfrm_add_pol_expire. In old code (at least back in the 2.6.18 days) err
wasn't used before the return when no policy is found and so the
initialization would cause err to be ENOENT. But since err has since
been used above when we don't get a policy back from the xfrm_policy_by*
function we would always return 0 instead of the intended ENOENT. Also
fixed some white space damage in the same area.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Venkat Yekkirala <vyekkirala@trustedcs.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noted by Kent Yoder, this function will always return an
error. Make sure it returns zero on success.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the address family to refer encap_family
when comparing with a kernel generated xfrm_state
Signed-off-by: Kazunori MIYAZAWA <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure that this function is called correctly, and
add BUG() checking to ensure the arguments are sane.
Based upon a patch by Joy Latten.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add CONFIG_NET_KEY_MIGRATE option which makes it possible for user
application to send or receive MIGRATE message to/from PF_KEY socket.
Signed-off-by: Shinta Sugimoto <shinta.sugimoto@ericsson.com>
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add CONFIG_XFRM_MIGRATE option which makes it possible for for user
application to send or receive MIGRATE message to/from netlink socket.
Signed-off-by: Shinta Sugimoto <shinta.sugimoto@ericsson.com>
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add user interface for handling XFRM_MSG_MIGRATE. The message is issued
by user application. When kernel receives the message, procedure of
updating XFRM databases will take place.
Signed-off-by: Shinta Sugimoto <shinta.sugimoto@ericsson.com>
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the XFRM framework so that endpoint address(es) in the XFRM
databases could be dynamically updated according to a request (MIGRATE
message) from user application. Target XFRM policy is first identified
by the selector in the MIGRATE message. Next, the endpoint addresses
of the matching templates and XFRM states are updated according to
the MIGRATE message.
Signed-off-by: Shinta Sugimoto <shinta.sugimoto@ericsson.com>
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch exports xfrm_state_afinfo.
Signed-off-by: Miika Komu <miika@iki.fi>
Signed-off-by: Diego Beltrami <Diego.Beltrami@hiit.fi>
Signed-off-by: Kazunori Miyazawa <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the entry of Camellia cipher algorithm to ealg_list[].
Signed-off-by: Noriaki TAKAMIYA <takamiya@po.ntts.co.jp>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The recent hashing introduced an off-by-one bug in policy list insertion.
Instead of adding after the last entry with a lesser or equal priority,
we're adding after the successor of that entry.
This patch fixes this and also adds a warning if we detect a duplicate
entry in the policy list. This should never happen due to this if clause.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
All ->doit handlers want a struct rtattr **, so pass down the right
type.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Installing an IPsec SA using old algorithm names (.compat) does not work
if the algorithm is not already loaded. When not using the PF_KEY
interface, algorithms are not preloaded in xfrm_probe_algs() and
installing a IPsec SA fails.
Signed-off-by: Martin Willi <martin@strongswan.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all uses of kmem_cache_t with struct kmem_cache.
The patch was generated using the following script:
#!/bin/sh
#
# Replace one string by another in all the kernel sources.
#
set -e
for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
quilt add $file
sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
mv /tmp/$$ $file
quilt refresh
done
The script was run like this
sh replace kmem_cache_t "struct kmem_cache"
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_ATOMIC is an alias of GFP_ATOMIC
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Disables auditing in ipsec when CONFIG_AUDITSYSCALL is
disabled in the kernel.
Also includes a bug fix for xfrm_state.c as a result of
original ipsec audit patch.
Signed-off-by: Joy Latten <latten@austin.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
An audit message occurs when an ipsec SA
or ipsec policy is created/deleted.
Signed-off-by: Joy Latten <latten@austin.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change optimizes the dumping of Security policies.
1) Before this change ..
speedopolis:~# time ./ip xf pol
real 0m22.274s
user 0m0.000s
sys 0m22.269s
2) Turn off sub-policies
speedopolis:~# ./ip xf pol
real 0m13.496s
user 0m0.000s
sys 0m13.493s
i suppose the above is to be expected
3) With this change ..
speedopolis:~# time ./ip x policy
real 0m7.901s
user 0m0.008s
sys 0m7.896s
Conflicts:
drivers/ata/libata-scsi.c
include/linux/libata.h
Futher merge of Linus's head and compilation fixups.
Signed-Off-By: David Howells <dhowells@redhat.com>
Conflicts:
drivers/infiniband/core/iwcm.c
drivers/net/chelsio/cxgb2.c
drivers/net/wireless/bcm43xx/bcm43xx_main.c
drivers/net/wireless/prism54/islpci_eth.c
drivers/usb/core/hub.h
drivers/usb/input/hid-core.c
net/core/netpoll.c
Fix up merge failures with Linus's head and fix new compilation failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
Since we never checked the ->family value of templates
before, many applications simply leave it at zero.
Detect this and fix it up to be the pol->family value.
Also, do not clobber xp->family while reading in templates,
that is not necessary.
Signed-off-by: David S. Miller <davem@davemloft.net>
aevents can not uniquely identify an SA. We break the ABI with this
patch, but consensus is that since it is not yet utilized by any
(known) application then it is fine (better do it now than later).
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Miika Komu <miika@iki.fi>
Signed-off-by: Diego Beltrami <Diego.Beltrami@hiit.fi>
Signed-off-by: Kazunori Miyazawa <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Miika Komu <miika@iki.fi>
Signed-off-by: Diego Beltrami <Diego.Beltrami@hiit.fi>
Signed-off-by: Kazunori Miyazawa <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Might as well make flush notifier prettier when subpolicy used
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
The destination PID is passed directly to netlink_unicast()
respectively netlink_multicast().
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make copy_to_user_policy_type take a type instead a policy and
fix its users to pass the type
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the selection of an SA for an outgoing packet to be at the same
context as the originating socket/flow. This eliminates the SELinux
policy's ability to use/sendto SAs with contexts other than the socket's.
With this patch applied, the SELinux policy will require one or more of the
following for a socket to be able to communicate with/without SAs:
1. To enable a socket to communicate without using labeled-IPSec SAs:
allow socket_t unlabeled_t:association { sendto recvfrom }
2. To enable a socket to communicate with labeled-IPSec SAs:
allow socket_t self:association { sendto };
allow socket_t peer_sa_t:association { recvfrom };
Signed-off-by: Venkat Yekkirala <vyekkirala@TrustedCS.com>
Signed-off-by: James Morris <jmorris@namei.org>
When application uses XFRM_MSG_GETSA to get state entry through
netlink socket and kernel has no matching one, the application expects
reply message with error status by kernel.
Kernel doesn't send the message back in the case of Mobile IPv6 route
optimization protocols (i.e. routing header or destination options
header). This is caused by incorrect return code "0" from
net/xfrm/xfrm_user.c(xfrm_user_state_lookup) and it makes kernel skip
to acknowledge at net/netlink/af_netlink.c(netlink_rcv_skb).
This patch fix to reply ESRCH to application.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: TAKAMIYA Noriaki <takamiya@po.ntts.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
I actually dont have a test case for these; i just found them by
inspection. Refer to patch "[XFRM]: Sub-policies broke policy events"
for more info
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Acked-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
XFRM policy events are broken when sub-policy feature is turned on.
A simple test to verify this:
run ip xfrm mon on one window and add then delete a policy on another
window ..
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Acked-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use memcpy() to move xfrm_address_t objects in and out
of netlink messages. The vast majority of xfrm_user was
doing this properly, except for copy_from_user_state()
and copy_to_user_state().
Signed-off-by: David S. Miller <davem@davemloft.net>
xfrm_state_num needs to be increased for XFRM_STATE_ACQ states created
by xfrm_state_find() to prevent the counter from going negative when
the state is destroyed.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Missing counter bump when hashing in a new ACQ
xfrm_state.
Now that we have two spots to do the hash grow
check, break it out into a helper function.
Signed-off-by: David S. Miller <davem@davemloft.net>
This treats the security errors encountered in the case of
socket policy matching, the same as how these are treated in
the case of main/sub policies, which is to return a full lookup
failure.
Signed-off-by: Venkat Yekkirala <vyekkirala@TrustedCS.com>
Signed-off-by: James Morris <jmorris@namei.org>
Currently when an IPSec policy rule doesn't specify a security
context, it is assumed to be "unlabeled" by SELinux, and so
the IPSec policy rule fails to match to a flow that it would
otherwise match to, unless one has explicitly added an SELinux
policy rule allowing the flow to "polmatch" to the "unlabeled"
IPSec policy rules. In the absence of such an explicitly added
SELinux policy rule, the IPSec policy rule fails to match and
so the packet(s) flow in clear text without the otherwise applicable
xfrm(s) applied.
The above SELinux behavior violates the SELinux security notion of
"deny by default" which should actually translate to "encrypt by
default" in the above case.
This was first reported by Evgeniy Polyakov and the way James Morris
was seeing the problem was when connecting via IPsec to a
confined service on an SELinux box (vsftpd), which did not have the
appropriate SELinux policy permissions to send packets via IPsec.
With this patch applied, SELinux "polmatching" of flows Vs. IPSec
policy rules will only come into play when there's a explicit context
specified for the IPSec policy rule (which also means there's corresponding
SELinux policy allowing appropriate domains/flows to polmatch to this context).
Secondly, when a security module is loaded (in this case, SELinux), the
security_xfrm_policy_lookup() hook can return errors other than access denied,
such as -EINVAL. We were not handling that correctly, and in fact
inverting the return logic and propagating a false "ok" back up to
xfrm_lookup(), which then allowed packets to pass as if they were not
associated with an xfrm policy.
The solution for this is to first ensure that errno values are
correctly propagated all the way back up through the various call chains
from security_xfrm_policy_lookup(), and handled correctly.
Then, flow_cache_lookup() is modified, so that if the policy resolver
fails (typically a permission denied via the security module), the flow
cache entry is killed rather than having a null policy assigned (which
indicates that the packet can pass freely). This also forces any future
lookups for the same flow to consult the security module (e.g. SELinux)
for current security policy (rather than, say, caching the error on the
flow cache entry).
This patch: Fix the selinux side of things.
This makes sure SELinux polmatching of flow contexts to IPSec policy
rules comes into play only when an explicit context is associated
with the IPSec policy rule.
Also, this no longer defaults the context of a socket policy to
the context of the socket since the "no explicit context" case
is now handled properly.
Signed-off-by: Venkat Yekkirala <vyekkirala@TrustedCS.com>
Signed-off-by: James Morris <jmorris@namei.org>
When a security module is loaded (in this case, SELinux), the
security_xfrm_policy_lookup() hook can return an access denied permission
(or other error). We were not handling that correctly, and in fact
inverting the return logic and propagating a false "ok" back up to
xfrm_lookup(), which then allowed packets to pass as if they were not
associated with an xfrm policy.
The way I was seeing the problem was when connecting via IPsec to a
confined service on an SELinux box (vsftpd), which did not have the
appropriate SELinux policy permissions to send packets via IPsec.
The first SYNACK would be blocked, because of an uncached lookup via
flow_cache_lookup(), which would fail to resolve an xfrm policy because
the SELinux policy is checked at that point via the resolver.
However, retransmitted SYNACKs would then find a cached flow entry when
calling into flow_cache_lookup() with a null xfrm policy, which is
interpreted by xfrm_lookup() as the packet not having any associated
policy and similarly to the first case, allowing it to pass without
transformation.
The solution presented here is to first ensure that errno values are
correctly propagated all the way back up through the various call chains
from security_xfrm_policy_lookup(), and handled correctly.
Then, flow_cache_lookup() is modified, so that if the policy resolver
fails (typically a permission denied via the security module), the flow
cache entry is killed rather than having a null policy assigned (which
indicates that the packet can pass freely). This also forces any future
lookups for the same flow to consult the security module (e.g. SELinux)
for current security policy (rather than, say, caching the error on the
flow cache entry).
Signed-off-by: James Morris <jmorris@namei.org>
This patch introduces the BEET mode (Bound End-to-End Tunnel) with as
specified by the ietf draft at the following link:
http://www.ietf.org/internet-drafts/draft-nikander-esp-beet-mode-06.txt
The patch provides only single family support (i.e. inner family =
outer family).
Signed-off-by: Diego Beltrami <diego.beltrami@gmail.com>
Signed-off-by: Miika Komu <miika@iki.fi>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Abhinav Pathak <abhinav.pathak@hiit.fi>
Signed-off-by: Jeff Ahrenholz <ahrenholz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we flush policies, we do a type match so we might not
actually delete all policies matching a certain direction.
So keep track of how many policies we actually kill and
subtract that number from xfrm_policy_count[dir] at the
end.
Based upon a patch by Masahide NAKAMURA.
Signed-off-by: David S. Miller <davem@davemloft.net>
Src hash is introduced for Mobile IPv6 route optimization usage.
On current kenrel code it is calculated with source address only.
It results we uses the same hash value for outbound state (when
the node has only one address for Mobile IPv6).
This patch use also destination address as peer information for
src hash to be dispersed.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
SPI=0 is used for acquired IPsec SA and MIPv6 RO state.
Such state should not be added to the SPI hash
because we do not care about it on deleting path.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
spi argument of xfrm_state_lookup() is net-endian
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hashing SAs by source address breaks templates with wildcards as tunnel
source since the source address used for hashing/lookup is still 0/0.
Move source address lookup to xfrm_tmpl_resolve_one() so we can use the
real address in the lookup.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems that during the MIPv6 respin, some code which was originally
conditionally compiled around CONFIG_XFRM_ADVANCED was accidently left
in after the config option was removed.
This patch removes an extraneous pointer (xerr_idxp) which is no
longer needed.
Signed-off-by: James Morris <jmorris@namei.org>
Acked-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if we find an exact match in the hash table,
we must inspect the inexact list to look for a match
with a better priority.
Noticed by Masahide NAKAMURA <nakam@linux-ipv6.org>.
Signed-off-by: David S. Miller <davem@davemloft.net>
This idea is from Alexey Kuznetsov.
It is common for policies to be non-prefixed. And for
that case we can optimize lookups, insert, etc. quite
a bit.
For each direction, we have a dynamically sized policy
hash table for non-prefixed policies. We also have a
hash table on policy->index.
For prefixed policies, we have a list per-direction which
we will consult on lookups when a non-prefix hashtable
lookup fails.
This still isn't as efficient as I would like it. There
are four immediate problems:
1) Lots of excessive refcounting, which can be fixed just
like xfrm_state was
2) We do 2 hash probes on insert, one to look for dups and
one to allocate a unique policy->index. Althought I wonder
how much this matters since xfrm_state inserts do up to
3 hash probes and that seems to perform fine.
3) xfrm_policy_insert() is very complex because of the priority
ordering and entry replacement logic.
4) Lots of counter bumping, in addition to policy refcounts,
in the form of xfrm_policy_count[]. This is merely used
to let code path(s) know that some IPSEC rules exist. So
this count is indexed per-direction, maybe that is overkill.
Signed-off-by: David S. Miller <davem@davemloft.net>
The source address is always non-prefixed so we should use
it to help give entropy to the bydst hash.
Signed-off-by: David S. Miller <davem@davemloft.net>
The refcounting done for timers and hash table insertions
are just wasted cycles. We can eliminate all of this
refcounting because:
1) The implicit refcount when the xfrm_state object is active
will always be held while the object is in the hash tables.
We never kfree() the xfrm_state until long after we've made
sure that it has been unhashed.
2) Timers are even easier. Once we mark that x->km.state as
anything other than XFRM_STATE_VALID (__xfrm_state_delete
sets it to XFRM_STATE_DEAD), any timer that fires will
do nothing and return without rearming the timer.
Therefore we can defer the del_timer calls until when the
object is about to be freed up during GC. We have to use
del_timer_sync() and defer it to GC because we can't do
a del_timer_sync() while holding x->lock which all callers
of __xfrm_state_delete hold.
This makes SA changes even more light-weight.
Signed-off-by: David S. Miller <davem@davemloft.net>
Just let GC and other normal mechanisms take care of getting
rid of DST cache references to deleted xfrm_state objects
instead of walking all the policy bundles.
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead, simply set all potentially aliasing existing xfrm_state
objects to have the current generation counter value.
This will make routes get relooked up the next time an existing
route mentioning these aliased xfrm_state objects gets used,
via xfrm_dst_check().
Signed-off-by: David S. Miller <davem@davemloft.net>
Each xfrm_state inserted gets a new generation counter
value. When a bundle is created, the xfrm_dst objects
get the current generation counter of the xfrm_state
they will attach to at dst->xfrm.
xfrm_bundle_ok() will return false if it sees an
xfrm_dst with a generation count different from the
generation count of the xfrm_state that dst points to.
This provides a facility by which to passively and
cheaply invalidate cached IPSEC routes during SA
database changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The grow algorithm is simple, we grow if:
1) we see a hash chain collision at insert, and
2) we haven't hit the hash size limit (currently 1*1024*1024 slots), and
3) the number of xfrm_state objects is > the current hash mask
All of this needs some tweaking.
Remove __initdata from "hashdist" so we can use it safely at run time.
Signed-off-by: David S. Miller <davem@davemloft.net>
Sub policy can be used through netlink socket.
PF_KEY uses main only and it is TODO to support sub.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under two transformation policies it is required to merge them.
This is a platform to sort state for outbound and templates
for inbound respectively.
It will be used when Mobile IPv6 and IPsec are used at the same time.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sub policy is introduced. Main and sub policy are applied the same flow.
(Policy that current kernel uses is named as main.)
It is required another transformation policy management to keep IPsec
and Mobile IPv6 lives separate.
Policy which lives shorter time in kernel should be a sub i.e. normally
main is for IPsec and sub is for Mobile IPv6.
(Such usage as two IPsec policies on different database can be used, too.)
Limitation or TODOs:
- Sub policy is not supported for per socket one (it is always inserted as main).
- Current kernel makes cached outbound with flowi to skip searching database.
However this patch makes it disabled only when "two policies are used and
the first matched one is bypass case" because neither flowi nor bundle
information knows about transformation template size.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Add Kconfig to support sub policy.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
XFRM_MSG_REPORT is a message as notification of state protocol and
selector from kernel to user-space.
Mobile IPv6 will use it when inbound reject is occurred at route
optimization to make user-space know a binding error requirement.
Based on MIPL2 kernel patch.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For Mobile IPv6 usage, it is required to trace which secpath state is
reject factor in order to notify it to user space (to know the address
which cannot be used route optimized communication).
Based on MIPL2 kernel patch.
This patch was also written by: Henrik Petander <petander@tcs.hut.fi>
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Mobile IPv6 route optimization protocols to netlink interface.
Route optimization states carry care-of address.
Based on MIPL2 kernel patch.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Transformation user interface is not only for IPsec.
Based on MIPL2 kernel patch.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For outbound transformation, bundle is checked whether it is
suitable for current flow to be reused or not. In such IPv6 case
as below, transformation may apply incorrect bundle for the flow instead
of creating another bundle:
- The policy selector has destination prefix length < 128
(Two or more addresses can be matched it)
- Its bundle holds dst entry of default route whose prefix length < 128
(Previous traffic was used such route as next hop)
- The policy and the bundle were used a transport mode state and
this time flow address is not matched the bundled state.
This issue is found by Mobile IPv6 usage to protect mobility signaling
by IPsec, but it is not a Mobile IPv6 specific.
This patch adds strict check to xfrm_bundle_ok() for each
state mode and address when prefix length is less than 128.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch transformation state is updated last used time
for each sending. Xtime is used for it like other state lifetime
expiration.
Mobile IPv6 enabled nodes will want to know traffic status of each
binding (e.g. judgement to request binding refresh by correspondent node,
or to keep home/care-of nonce alive by mobile node).
The last used timestamp is an important hint about it.
Based on MIPL2 kernel patch.
This patch was also written by: Henrik Petander <petander@tcs.hut.fi>
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Care-of address is carried by state as a transformation option like
IPsec encryption/authentication algorithm.
Based on MIPL2 kernel patch.
Signed-off-by: Noriaki TAKAMIYA <takamiya@po.ntts.co.jp>
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
On current kernel inbound transformation state is allowed transport and
disallowed tunnel mode when mismatch is occurred between tempates and states.
As the result of adding two more modes by Mobile IPv6, this function name
is misleading. Inbound transformation can allow only transport mode
when mismatch is occurred between template and secpath.
Based on MIPL2 kernel patch.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
XFRM_STATE_WILDRECV flag is introduced; the last resort state is set
it and receives packet which is not route optimized but uses such
extension headers i.e. Mobile IPv6 signaling (binding update and
acknowledgement). A node enabled Mobile IPv6 adds the state.
Based on MIPL2 kernel patch.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For Mobile IPv6 usage, routing header or destination options header is
used and it doesn't require this comparison. It is checked only for
IPsec template.
Based on MIPL2 kernel patch.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a support to search transformation states by its addresses
by using source address list for Mobile IPv6 usage.
To use it from user-space, it is also added a message type for
source address as a xfrm state option.
Based on MIPL2 kernel patch.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support source address based searching.
Mobile IPv6 will use it.
Based on MIPL2 kernel patch.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It will be added two more transformation protocols (routing header
and destination options header) for Mobile IPv6.
xfrm_id_proto_match() can be handle zero as all, IPSEC_PROTO_ANY as
all IPsec and otherwise as exact one.
Based on MIPL2 kernel patch.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put the helper to header for future use.
Based on MIPL2 kernel patch.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Transformation mode is used as either IPsec transport or tunnel.
It is required to add two more items, route optimization and inbound trigger
for Mobile IPv6.
Based on MIPL2 kernel patch.
This patch was also written by: Ville Nuorvala <vnuorval@tcs.hut.fi>
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This defaults the label of socket-specific IPSec policies to be the
same as the socket they are set on.
Signed-off-by: Venkat Yekkirala <vyekkirala@TrustedCS.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This labels the flows that could utilize IPSec xfrms at the points the
flows are defined so that IPSec policy and SAs at the right label can
be used.
The following protos are currently not handled, but they should
continue to be able to use single-labeled IPSec like they currently
do.
ipmr
ip_gre
ipip
igmp
sit
sctp
ip6_tunnel (IPv6 over IPv6 tunnel device)
decnet
Signed-off-by: Venkat Yekkirala <vyekkirala@TrustedCS.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This includes the security context of a security association created
for use by IKE in the acquire messages sent to IKE daemons using
netlink/xfrm_user. This would allow the daemons to include the
security context in the negotiation, so that the resultant association
is unique to that security context.
Signed-off-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements a seemless mechanism for xfrm policy selection and
state matching based on the flow sid. This also includes the necessary
SELinux enforcement pieces.
Signed-off-by: Venkat Yekkirala <vyekkirala@TrustedCS.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts IPsec to use the new HMAC template. The names of
existing simple digest algorithms may still be used to refer to their
HMAC composites.
The same structure can be used by other MACs such as AES-XCBC-MAC.
This patch also switches from the digest interface to hash.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts IPSec/ESP to use the new block cipher type where
applicable. Similar to the HMAC conversion, existing algorithm names
have been kept for compatibility.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds a compatibility name field for each IPsec algorithm. This
is needed when parameterised algorithms are used. For example, "md5" will
become "hmac(md5)", and "aes" will become "cbc(aes)".
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The header file linux/crypto.h is only needed by a few files so including
it in net/xfrm.h (which is included by half of the networking stack) is a
waste. This patch moves it out of net/xfrm.h and into the specific header
files that actually need it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If dst->obsolete is -1, this is a signal from the
bundle creator that we want the XFRM dst and the
dsts that it references to be validated on every
use.
I misunderstood this intention when I changed
xfrm_dst_check() to always return NULL.
Now, when we purge a dst entry, by running dst_free()
on it. This will set the dst->obsolete to a positive
integer, and we want to return NULL in that case so
that the socket does a relookup for the route.
Thus, if dst->obsolete<0, let stale_bundle() validate
the state, else always return NULL.
In general, we need to do things more intelligently
here because we flush too much state during rule
changes. Herbert Xu has some ideas wherein the key
manager gives us some help in this area. We can also
use smarter state management algorithms inside of
the kernel as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the unused EXPORT_SYMBOL(xfrm_state_mtu).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch encapsulates the usage of eff_cap (in netlink_skb_params) within
the security framework by extending security_netlink_recv to include a required
capability parameter and converting all direct usage of eff_caps outside
of the lsm modules to use the interface. It also updates the SELinux
implementation of the security_netlink_send and security_netlink_recv
hooks to take advantage of the sid in the netlink_skb_params struct.
This also enables SELinux to perform auditing of netlink capability checks.
Please apply, for 2.6.18 if possible.
Signed-off-by: Darrel Goeddel <dgoeddel@trustedcs.com>
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assignment used as truth value in xfrm_del_sa()
and xfrm_get_policy().
Wrong argument type declared for security_xfrm_state_delete()
when SELINUX is disabled.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains a fix for the previous patch that adds security
contexts to IPsec policies and security associations. In the previous
patch, no authorization (besides the check for write permissions to
SAD and SPD) is required to delete IPsec policies and security
assocations with security contexts. Thus a user authorized to change
SAD and SPD can bypass the IPsec policy authorization by simply
deleteing policies with security contexts. To fix this security hole,
an additional authorization check is added for removing security
policies and security associations with security contexts.
Note that if no security context is supplied on add or present on
policy to be deleted, the SELinux module allows the change
unconditionally. The hook is called on deletion when no context is
present, which we may want to change. At present, I left it up to the
module.
LSM changes:
The patch adds two new LSM hooks: xfrm_policy_delete and
xfrm_state_delete. The new hooks are necessary to authorize deletion
of IPsec policies that have security contexts. The existing hooks
xfrm_policy_free and xfrm_state_free lack the context to do the
authorization, so I decided to split authorization of deletion and
memory management of security data, as is typical in the LSM
interface.
Use:
The new delete hooks are checked when xfrm_policy or xfrm_state are
deleted by either the xfrm_user interface (xfrm_get_policy,
xfrm_del_sa) or the pfkey interface (pfkey_spddelete, pfkey_delete).
SELinux changes:
The new policy_delete and state_delete functions are added.
Signed-off-by: Catherine Zhang <cxzhang@watson.ibm.com>
Signed-off-by: Trent Jaeger <tjaeger@cse.psu.edu>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the structure xfrm_mode. It is meant to represent
the operations carried out by transport/tunnel modes.
By doing this we allow additional encapsulation modes to be added
without clogging up the xfrm_input/xfrm_output paths.
Candidate modes include 4-to-6 tunnel mode, 6-to-4 tunnel mode, and
BEET modes.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of locks used to manage afinfo structures can easily be reduced
down to one each for policy and state respectively. This is based on the
observation that the write locks are only held by module insertion/removal
which are very rare events so there is no need to further differentiate
between the insertion of modules like ipv6 versus esp6.
The removal of the read locks in xfrm4_policy.c/xfrm6_policy.c might look
suspicious at first. However, after you realise that nobody ever takes
the corresponding write lock you'll feel better :)
As far as I can gather it's an attempt to guard against the removal of
the corresponding modules. Since neither module can be unloaded at all
we can leave it to whoever fixes up IPv6 unloading :)
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
xfrm_policy_afinfo_lock can be taken in bh context, at:
[<c013fe1a>] lockdep_acquire_read+0x54/0x6d
[<c0f6e024>] _read_lock+0x15/0x22
[<c0e8fcdb>] xfrm_policy_get_afinfo+0x1a/0x3d
[<c0e8fd10>] xfrm_decode_session+0x12/0x32
[<c0e66094>] ip_route_me_harder+0x1c9/0x25b
[<c0e770d3>] ip_nat_local_fn+0x94/0xad
[<c0e2bbc8>] nf_iterate+0x2e/0x7a
[<c0e2bc50>] nf_hook_slow+0x3c/0x9e
[<c0e3a342>] ip_push_pending_frames+0x2de/0x3a7
[<c0e53e19>] icmp_push_reply+0x136/0x141
[<c0e543fb>] icmp_reply+0x118/0x1a0
[<c0e54581>] icmp_echo+0x44/0x46
[<c0e53fad>] icmp_rcv+0x111/0x138
[<c0e36764>] ip_local_deliver+0x150/0x1f9
[<c0e36be2>] ip_rcv+0x3d5/0x413
[<c0df760f>] netif_receive_skb+0x337/0x356
[<c0df76c3>] process_backlog+0x95/0x110
[<c0df5fe2>] net_rx_action+0xa5/0x16d
[<c012d8a7>] __do_softirq+0x6f/0xe6
[<c0105ec2>] do_softirq+0x52/0xb1
this means that all write-locking of xfrm_policy_afinfo_lock must be
bh-safe. This patch fixes xfrm_policy_register_afinfo() and
xfrm_policy_unregister_afinfo().
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
xfrm_state_afinfo_lock can be read-locked from bh context, so take it
in a bh-safe manner in xfrm_state_register_afinfo() and
xfrm_state_unregister_afinfo(). Found by the lock validator.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
xfrm typemap->lock may be used in softirq context, so all write_lock()
uses must be softirq-safe.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send aevent immediately if we have sent nothing since last timer and
this is the first packet.
Fixes a corner case when packet threshold is very high, the timer low
and a very low packet rate input which is bursty.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the *_decap_state structures which were previously
used to share state between input/post_input. This is no longer
needed.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When xfrm_user isn't loaded xfrm_nl is NULL, which makes IPsec crash because
xfrm_aevent_is_on passes the NULL pointer to netlink_has_listeners as socket.
A second problem is that the xfrm_nl pointer is not cleared when the socket
is releases at module unload time.
Protect references of xfrm_nl from outside of xfrm_user by RCU, check
that the socket is present in xfrm_aevent_is_on and set it to NULL
when unloading xfrm_user.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
First, it warns when PAGE_SIZE >= 64K because the ctx_len
field is 16-bits.
Secondly, if there are any real length limitations it can
be verified by the security layer security_xfrm_state_alloc()
call.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is similar to the SA expire insertion patch - only it inserts
expires for SP.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows a user to insert SA expires. This is useful to
do on an HA backup for the case of byte counts but may not be very
useful for the case of time based expiry.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces a feature similar to the one described in RFC 2367:
"
... the application needing an SA sends a PF_KEY
SADB_ACQUIRE message down to the Key Engine, which then either
returns an error or sends a similar SADB_ACQUIRE message up to one or
more key management applications capable of creating such SAs.
...
...
The third is where an application-layer consumer of security
associations (e.g. an OSPFv2 or RIPv2 daemon) needs a security
association.
Send an SADB_ACQUIRE message from a user process to the kernel.
<base, address(SD), (address(P),) (identity(SD),) (sensitivity,)
proposal>
The kernel returns an SADB_ACQUIRE message to registered
sockets.
<base, address(SD), (address(P),) (identity(SD),) (sensitivity,)
proposal>
The user-level consumer waits for an SADB_UPDATE or SADB_ADD
message for its particular type, and then can use that
association by using SADB_GET messages.
"
An app such as OSPF could then use ipsec KM to get keys
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides the core functionality needed for sync events
for ipsec. Derived work of Krisztian KOVACS <hidden@balabit.hu>
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only reason post_input exists at all is that it gives us the
potential to adjust the checksums incrementally in future which
we ought to do.
However, after thinking about it for a bit we can adjust the
checksums without using this post_input stuff at all. The crucial
point is that only the inner-most NAT-T SA needs to be considered
when adjusting checksums. What's more, the checksum adjustment
comes down to a single u32 due to the linearity of IP checksums.
We just happen to have a spare u32 lying around in our skb structure :)
When ip_summed is set to CHECKSUM_NONE on input, the value of skb->csum
is currently unused. All we have to do is to make that the checksum
adjustment and voila, there goes all the post_input and decap structures!
I've left in the decap data structures for now since it's intricately
woven into the sec_path stuff. We can kill them later too.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We often just do an atomic_dec(&x->refcnt) on an xfrm_state object
because we know there is more than 1 reference remaining and thus
we can elide the heavier xfrm_state_put() call.
Do this behind an inline function called __xfrm_state_put() so that is
more obvious and also to allow us to more cleanly add refcount
debugging later.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge-netfilter code attaches a fake dst_entry with dst->ops == NULL
to purely bridged packets. When these packets are SNATed and a policy
lookup is done, xfrm_lookup crashes because it tries to dereference
dst->ops.
Change xfrm_lookup not to dereference dst->ops before checking for the
DST_NOXFRM flag and set this flag in the fake dst_entry.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Problem discovered and initial patch by Olaf Kirch:
there's a problem with IPsec that has been bugging some of our users
for the last couple of kernel revs. Every now and then, IPsec will
freeze the machine completely. This is with openswan user land,
and with kernels up to and including 2.6.16-rc2.
I managed to debug this a little, and what happens is that we end
up looping in xfrm_lookup, and never get out. With a bit of debug
printks added, I can this happening:
ip_route_output_flow calls xfrm_lookup
xfrm_find_bundle returns NULL (apparently we're in the
middle of negotiating a new SA or something)
We therefore call xfrm_tmpl_resolve. This returns EAGAIN
We go to sleep, waiting for a policy update.
Then we loop back to the top
Apparently, the dst_orig that was passed into xfrm_lookup
has been dropped from the routing table (obsolete=2)
This leads to the endless loop, because we now create
a new bundle, check the new bundle and find it's stale
(stale_bundle -> xfrm_bundle_ok -> dst_check() return 0)
People have been testing with the patch below, which seems to fix the
problem partially. They still see connection hangs however (things
only clear up when they start a new ping or new ssh). So the patch
is obvsiouly not sufficient, and something else seems to go wrong.
I'm grateful for any hints you may have...
I suggest that we simply bail out always. If the dst decides to die
on us later on, the packet will be dropped anyway. So there is no
great urgency to retry here. Once we have the proper resolution
queueing, we can then do the retry again.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Olaf Kirch <okir@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
A bunch of asm/bug.h includes are both not needed (since it will get
pulled anyway) and bogus (since they are done too early). Removed.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This changes some simple "if (x) BUG();" statements to "BUG_ON(x);"
Signed-off-by: Kris Katterjohn <kjak@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle NAT of decapsulated IPsec packets by reconstructing the struct flowi
of the original packet from the conntrack information for IPsec policy
checks.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_route_me_harder doesn't use the port numbers of the xfrm lookup and
uses ip_route_input for non-local addresses which doesn't do a xfrm
lookup, ip6_route_me_harder doesn't do a xfrm lookup at all.
Use xfrm_decode_session and do the lookup manually, make sure both
only do the lookup if the packet hasn't been transformed already.
Makeing sure the lookup only happens once needs a new field in the
IP6CB, which exceeds the size of skb->cb. The size of skb->cb is
increased to 48b. Apparently the IPv6 mobile extensions need some
more room anyway.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains two corrections to the LSM-IPsec Nethooks patches
previously applied.
(1) free a security context on a failed insert via xfrm_user
interface in xfrm_add_policy. Memory leak.
(2) change the authorization of the allocation of a security context
in a xfrm_policy or xfrm_state from both relabelfrom and relabelto
to setcontext.
Signed-off-by: Trent Jaeger <tjaeger@cse.psu.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch series implements per packet access control via the
extension of the Linux Security Modules (LSM) interface by hooks in
the XFRM and pfkey subsystems that leverage IPSec security
associations to label packets. Extensions to the SELinux LSM are
included that leverage the patch for this purpose.
This patch implements the changes necessary to the XFRM subsystem,
pfkey interface, ipv4/ipv6, and xfrm_user interface to restrict a
socket to use only authorized security associations (or no security
association) to send/receive network packets.
Patch purpose:
The patch is designed to enable access control per packets based on
the strongly authenticated IPSec security association. Such access
controls augment the existing ones based on network interface and IP
address. The former are very coarse-grained, and the latter can be
spoofed. By using IPSec, the system can control access to remote
hosts based on cryptographic keys generated using the IPSec mechanism.
This enables access control on a per-machine basis or per-application
if the remote machine is running the same mechanism and trusted to
enforce the access control policy.
Patch design approach:
The overall approach is that policy (xfrm_policy) entries set by
user-level programs (e.g., setkey for ipsec-tools) are extended with a
security context that is used at policy selection time in the XFRM
subsystem to restrict the sockets that can send/receive packets via
security associations (xfrm_states) that are built from those
policies.
A presentation available at
www.selinux-symposium.org/2005/presentations/session2/2-3-jaeger.pdf
from the SELinux symposium describes the overall approach.
Patch implementation details:
On output, the policy retrieved (via xfrm_policy_lookup or
xfrm_sk_policy_lookup) must be authorized for the security context of
the socket and the same security context is required for resultant
security association (retrieved or negotiated via racoon in
ipsec-tools). This is enforced in xfrm_state_find.
On input, the policy retrieved must also be authorized for the socket
(at __xfrm_policy_check), and the security context of the policy must
also match the security association being used.
The patch has virtually no impact on packets that do not use IPSec.
The existing Netfilter (outgoing) and LSM rcv_skb hooks are used as
before.
Also, if IPSec is used without security contexts, the impact is
minimal. The LSM must allow such policies to be selected for the
combination of socket and remote machine, but subsequent IPSec
processing proceeds as in the original case.
Testing:
The pfkey interface is tested using the ipsec-tools. ipsec-tools have
been modified (a separate ipsec-tools patch is available for version
0.5) that supports assignment of xfrm_policy entries and security
associations with security contexts via setkey and the negotiation
using the security contexts via racoon.
The xfrm_user interface is tested via ad hoc programs that set
security contexts. These programs are also available from me, and
contain programs for setting, getting, and deleting policy for testing
this interface. Testing of sa functions was done by tracing kernel
behavior.
Signed-off-by: Trent Jaeger <tjaeger@cse.psu.edu>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The problem is that when new policies are inserted, sockets do not see
the update (but all new route lookups do).
This bug is related to the SA insertion stale route issue solved
recently, and this policy visibility problem can be fixed in a similar
way.
The fix is to flush out the bundles of all policies deeper than the
policy being inserted. Consider beginning state of "outgoing"
direction policy list:
policy A --> policy B --> policy C --> policy D
First, realize that inserting a policy into a list only potentially
changes IPSEC routes for that direction. Therefore we need not bother
considering the policies for other directions. We need only consider
the existing policies in the list we are doing the inserting.
Consider new policy "B'", inserted after B.
policy A --> policy B --> policy B' --> policy C --> policy D
Two rules:
1) If policy A or policy B matched before the insertion, they
appear before B' and thus would still match after inserting
B'
2) Policy C and D, now "shadowed" and after policy B', potentially
contain stale routes because policy B' might be selected
instead of them.
Therefore we only need flush routes assosciated with policies
appearing after a newly inserted policy, if any.
Signed-off-by: David S. Miller <davem@davemloft.net>
When we insert a new xfrm_state which potentially
subsumes an existing one, make sure all cached
bundles are flushed so that the new SA is used
immediately.
Signed-off-by: David S. Miller <davem@davemloft.net>
Most netlink families make no use of the done() callback, making
it optional gets rid of all unnecessary dummy implementations.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Jesper Juhl <jesper.juhl@gmail.com>
This is the net/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in net/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Arnaldo Carvalho de Melo <acme@conectiva.com.br>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Now that we've switched over to storing MTUs in the xfrm_dst entries,
we no longer need the dst's get_mss methods. This patch gets rid of
them.
It also documents the fact that our MTU calculation is not optimal
for ESP.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
- added typedef unsigned int __nocast gfp_t;
- replaced __nocast uses for gfp flags with gfp_t - it gives exactly
the same warnings as far as sparse is concerned, doesn't change
generated code (from gcc point of view we replaced unsigned int with
typedef) and documents what's going on far better.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here is a patch that adds a helper called xfrm_policy_id2dir to
document the fact that the policy direction can be and is derived
from the index.
This is based on a patch by YOSHIFUJI Hideaki and 210313105@suda.edu.cn.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix implicit nocast warnings in xfrm code:
net/xfrm/xfrm_policy.c:232:47: warning: implicit cast to nocast type
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch puts mostly read only data in the right section
(read_mostly), to help sharing of these data between CPUS without
memory ping pongs.
On one of my production machine, tcp_statistics was sitting in a
heavily modified cache line, so *every* SNMP update had to force a
reload.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netlink_broadcast users must initialize NETLINK_CB(skb).dst_groups to the
destination group mask for netlink_recvmsg.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Remove bogus code for compiling netlink as module
- Add module refcounting support for modules implementing a netlink
protocol
- Add support for autoloading modules that implement a netlink protocol
as soon as someone opens a socket for that protocol
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spotted by, and original patch by, Balazs Scheidler.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the protocol specific config options out to the specific protocols.
With this change net/Kconfig now starts to become readable and serve as a
good basis for further re-structuring.
The menu structure is left almost intact, except that indention is
fixed in most cases. Most visible are the INET changes where several
"depends on INET" are replaced with a single ifdef INET / endif pair.
Several new files were created to accomplish this change - they are
small but serve the purpose that config options are now distributed
out where they belongs.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the xfrm_state_afinfo->init_flags hook which allows
each address family to perform any common initialisation that does
not require a corresponding destructor call.
It will be used subsequently to set the XFRM_STATE_NOPMTUDISC flag
in IPv4.
It also fixes up the error codes returned by xfrm_init_state.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: James Morris <jmorris@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds xfrm_init_state which is simply a wrapper that calls
xfrm_get_type and subsequently x->type->init_state. It also gets rid
of the unused args argument.
Abstracting it out allows us to add common initialisation code, e.g.,
to set family-specific flags.
The add_time setting in xfrm_user.c was deleted because it's already
set by xfrm_state_alloc.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: James Morris <jmorris@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the format of the XFRM_MSG_DELSA and
XFRM_MSG_DELPOLICY notification so that the main message
sent is of the same format as that received by the kernel
if the original message was via netlink. This also means
that we won't lose the byid information carried in km_event.
Since this user interface is introduced by Jamal's patch
we can still afford to change it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Small fixup to use netlink macros instead of hardcoding.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu wrote:
> @@ -1254,6 +1326,7 @@ static int pfkey_add(struct sock *sk, st
> if (IS_ERR(x))
> return PTR_ERR(x);
>
> + xfrm_state_hold(x);
This introduces a leak when xfrm_state_add()/xfrm_state_update()
fail. We hold two references (one from xfrm_state_alloc(), one
from xfrm_state_hold()), but only drop one. We need to take the
reference because the reference from xfrm_state_alloc() can
be dropped by __xfrm_state_delete(), so the fix is to drop both
references on error. Same problem in xfrm_user.c.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes XFRM_SAP_* and converts them over to XFRM_MSG_*.
The netlink interface is meant to map directly onto the underlying
xfrm subsystem. Therefore rather than using a new independent
representation for the events we can simply use the existing ones
from xfrm_user.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch fixes policy deletion in xfrm_user so that it sets
km_event.data.byid. This puts xfrm_user on par with what af_key
does in this case.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch ensures that the hard state/policy expire notifications are
only sent when the state/policy is successfully removed from their
respective tables.
As it is, it's possible for a state/policy to both expire through
reaching a hard limit, as well as being deleted by the user.
Note that this behaviour isn't actually forbidden by RFC 2367.
However, it is a quality of implementation issue.
As an added bonus, the restructuring in this patch will help
eventually in moving the expire notifications from softirq
context into process context, thus improving their reliability.
One important side-effect from this change is that SAs reaching
their hard byte/packet limits are now deleted immediately, just
like SAs that have reached their hard time limits.
Previously they were announced immediately but only deleted after
30 seconds.
This is bad because it prevents the system from issuing an ACQUIRE
command until the existing state was deleted by the user or expires
after the time is up.
In the scenario where the expire notification was lost this introduces
a 30 second delay into the system for no good reason.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Heres the final patch.
What this patch provides
- netlink xfrm events
- ability to have events generated by netlink propagated to pfkey
and vice versa.
- fixes the acquire lets-be-happy-with-one-success issue
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
[XFRM] Call dst_check() with appropriate cookie
This fixes infinite loop issue with IPv6 tunnel mode.
Signed-off-by: Kazunori Miyazawa <kazunori@miyazawa.org>
Signed-off-by: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to verify that the payload contains enough data so that
attach_one_algo can copy alg_key_len bits from the payload.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable alg_key_len is in bits and not bytes. The function
attach_one_algo is currently using it as if it were in bytes.
This causes it to read memory which may not be there.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like skb_cow_data() does not set
proper owner for newly created skb.
If we have several fragments for skb and some of them
are shared(?) or cloned (like in async IPsec) there
might be a situation when we require recreating skb and
thus using skb_copy() for it.
Newly created skb has neither a destructor nor a socket
assotiated with it, which must be copied from the old skb.
As far as I can see, current code sets destructor and socket
for the first one skb only and uses truesize of the first skb
only to increment sk_wmem_alloc value.
If above "analysis" is correct then attached patch fixes that.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
I found a bug that stopped IPsec/IPv6 from working. About
a month ago IPv6 started using rt6i_idev->dev on the cached socket dst
entries. If the cached socket dst entry is IPsec, then rt6i_idev will
be NULL.
Since we want to look at the rt6i_idev of the original route in this
case, the easiest fix is to store rt6i_idev in the IPsec dst entry just
as we do for a number of other IPv6 route attributes. Unfortunately
this means that we need some new code to handle the references to
rt6i_idev. That's why this patch is bigger than it would otherwise be.
I've also done the same thing for IPv4 since it is conceivable that
once these idev attributes start getting used for accounting, we
probably need to dereference them for IPv4 IPsec entries too.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we free up a partially processed packet because it's
skb->len dropped to zero, we need to decrement qlen because
we are dropping out of the top-level loop so it will do
the decrement for us.
Spotted by Herbert Xu.
Signed-off-by: David S. Miller <davem@davemloft.net>
The qlen should continue to decrement, even if we
pop partially processed SKBs back onto the receive queue.
Signed-off-by: David S. Miller <davem@davemloft.net>
Let's recap the problem. The current asynchronous netlink kernel
message processing is vulnerable to these attacks:
1) Hit and run: Attacker sends one or more messages and then exits
before they're processed. This may confuse/disable the next netlink
user that gets the netlink address of the attacker since it may
receive the responses to the attacker's messages.
Proposed solutions:
a) Synchronous processing.
b) Stream mode socket.
c) Restrict/prohibit binding.
2) Starvation: Because various netlink rcv functions were written
to not return until all messages have been processed on a socket,
it is possible for these functions to execute for an arbitrarily
long period of time. If this is successfully exploited it could
also be used to hold rtnl forever.
Proposed solutions:
a) Synchronous processing.
b) Stream mode socket.
Firstly let's cross off solution c). It only solves the first
problem and it has user-visible impacts. In particular, it'll
break user space applications that expect to bind or communicate
with specific netlink addresses (pid's).
So we're left with a choice of synchronous processing versus
SOCK_STREAM for netlink.
For the moment I'm sticking with the synchronous approach as
suggested by Alexey since it's simpler and I'd rather spend
my time working on other things.
However, it does have a number of deficiencies compared to the
stream mode solution:
1) User-space to user-space netlink communication is still vulnerable.
2) Inefficient use of resources. This is especially true for rtnetlink
since the lock is shared with other users such as networking drivers.
The latter could hold the rtnl while communicating with hardware which
causes the rtnetlink user to wait when it could be doing other things.
3) It is still possible to DoS all netlink users by flooding the kernel
netlink receive queue. The attacker simply fills the receive socket
with a single netlink message that fills up the entire queue. The
attacker then continues to call sendmsg with the same message in a loop.
Point 3) can be countered by retransmissions in user-space code, however
it is pretty messy.
In light of these problems (in particular, point 3), we should implement
stream mode netlink at some point. In the mean time, here is a patch
that implements synchronous processing.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converts xfrm_msg_min and xfrm_dispatch to use c99 designated
initializers to make greping a little bit easier. Also replaces
two hardcoded message type with meaningful names.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use 'daddr' instead of &tmpl->id.daddr, since the latter
might be zero. Also, only perform the lookup when
tmpl->id.spi is non-zero.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Patrick McHardy