The Kconfig currently controlling compilation of this code is:
drivers/i2c/busses/Kconfig:config I2C_PXA_PCI
drivers/i2c/busses/Kconfig: def_bool I2C_PXA && X86_32 && PCI && OF
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_pci_driver() uses the same init level priority as
builtin_pci_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver allows I2C routing controlled through CPLD select registers on
a wide range of Mellanox systems (CPLD Lattice device).
MUX selection is provided by digital and analog HW. Analog part is not
under SW control.
Digital part is under CPLD control (channel selection/de-selection).
Connectivity schema.
.---. .-------------.
| l | | |-- i2cx1 -- i2cx8
| i |-- i2cn --+--| mlxcpld mux |
| n | | | |-- i2cy1 -- i2cy8
| u | | '-------------'
| x | | |
'---' '---------'
i2c-mux-mlxpcld does not necessarily require i2c-mlxcpld. It can be used
along with another bus driver, and still control i2c routing through CPLD
mux selection, in case the system is equipped with CPLD capable of mux
selection control.
The Kconfig currently controlling compilation of this code is:
drivers/i2c/muxes/Kconfig:config I2C_MUX_MLXCPLD
Signed-off-by: Michael Shych <michaelsh@mellanox.com>
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This will aid the seamless removal of the current probe()'s, more
commonly unused than used second parameter. Most I2C drivers can
simply switch over to the new interface, others which have DT
support can use its own matching instead and others can call
i2c_match_id() themselves. This brings I2C's device probe method
into line with other similar interfaces in the kernel and prevents
the requirement to pass an i2c_device_id table.
Suggested-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Kieran: fix rebase conflicts and adapt for dev_pm_domain_{attach,detach}]
Tested-by: Kieran Bingham <kieran@bingham.xyz>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kieran Bingham <kieran@bingham.xyz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When there was no other way to match a I2C device to driver i2c_match_id()
was exclusively used. However, now there are other types of tables which
are commonly supplied, matching on an i2c_device_id table is used less
frequently. Instead of _always_ calling i2c_match_id() from within the
framework, we only need to do so from drivers which have no other way of
matching. This patch makes i2c_match_id() available to the aforementioned
device drivers.
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Kieran Bingham <kieran@bingham.xyz>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kieran Bingham <kieran@bingham.xyz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently the I2C framework insists on devices supplying an I2C ID
table. Many of the devices which do so unnecessarily adding quite a
few wasted lines to kernel code. This patch allows drivers a means
to 'not' supply the aforementioned table and match on DT match tables
instead.
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Kieran Bingham <kieran@bingham.xyz>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kieran Bingham <kieran@bingham.xyz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This function provides a single call for all I2C devices which need to
match firstly using traditional OF means i.e by of_node, then if that
fails we attempt to match using the supplied I2C client name with a
list of supplied compatible strings with the '<vendor>,' string
removed. The latter is required due to the unruly naming conventions
used currently by I2C devices.
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Kieran: Fix static inline usage on !CONFIG_OF]
Tested-by: Kieran Bingham <kieran@bingham.xyz>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kieran Bingham <kieran@bingham.xyz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
A great deal of I2C devices are currently matched via DT node name, and
as such the compatible naming convention of '<vendor>,<device>' has gone
somewhat awry - some nodes don't supply one, some supply an arbitrary
string and others the correct device name with an arbitrary vendor prefix.
In an effort to correct this problem we have to supply a mechanism to
match a device by compatible string AND by simple device name. This
function strips off the '<vendor>,' part of a supplied compatible string
and attempts to match without it.
It is also used for sysfs, where a user can choose to instantiate a
device on an i2c bus using the sysfs interface by providing a string and
address to match and communicate with the device on the bus. Presently
this string is only matched against the old i2c device id style strings,
even in the presence of full device tree compatible strings with vendor
prefixes.
Providing a vendor-prefixed string to the sysfs interface will not match
against the device tree of_match_device() calls as there is no device
tree node to parse from the sysfs interface.
This function can match both vendor prefixed and stripped compatible
strings on the sysfs interface.
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kieran Bingham <kieran@bingham.xyz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Here we're providing dereference protection for i2c_match_id(), which
saves us having to do it each time it's called. We're also stripping
out the (now) needless checks in i2c_device_match(). This patch paves
the way for other, similar code trimming.
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Kieran Bingham <kieran@bingham.xyz>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kieran Bingham <kieran@bingham.xyz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Support a dynamic clock by reading the frequency and setting the
divisor in the transfer function instead of during probe.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use i2c_adapter->timeout for the completion timeout value. The core
default is 1 second.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Documentation/i2c/i2c-protocol states that Combined transactions should
separate messages with a Start bit and end the whole transaction with a
Stop bit. This patch adds support for issuing only a Start between
messages instead of a Stop followed by a Start.
This implementation differs from downstream i2c-bcm2708 in 2 respects:
- it uses an interrupt to detect that the transfer is active instead
of using polling. There is no interrupt for Transfer Active, but by
not prefilling the FIFO it's possible to use the TXW interrupt.
- when resetting/disabling the controller between transfers it writes
CLEAR to the control register instead of just zero.
Using just zero gave many errors. This might be the reason why
downstream had to disable this feature and make it available with a
module parameter.
I have run thousands of transfers to a DS1307 (rtc), MMA8451 (accel)
and AT24C32 (eeprom) in parallel without problems.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The controller can't support this flag, so remove it.
Documentation/i2c/i2c-protocol states that all of the message is sent:
I2C_M_IGNORE_NAK:
Normally message is interrupted immediately if there is [NA] from the
client. Setting this flag treats any [NA] as [A], and all of
message is sent.
>From the BCM2835 ARM Peripherals datasheet:
The ERR field is set when the slave fails to acknowledge either
its address or a data byte written to it.
So when the controller doesn't receive an ack, it sets ERR and raises
an interrupt. In other words, the whole message is not sent.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Writing to an AT24C32 generates on average 2x i2c transfer errors per
32-byte page write. Which amounts to a lot for a 4k write. This is due
to the fact that the chip doesn't respond during it's internal write
cycle when the at24 driver tries and retries the next write.
Only a handful drivers use dev_err() on transfer error, so switch to
dev_dbg() instead.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If an unexpected TXW or RXR interrupt occurs (msg_buf_remaining == 0),
the driver has no way to fill/drain the FIFO to stop the interrupts.
In this case the controller has to be disabled and the transfer
completed to avoid hang.
(CLKT | ERR) and DONE interrupts are completed in their own paths, and
the controller is disabled in the transfer function after completion.
Unite the code paths and do disabling inside the interrupt routine.
Clear interrupt status bits in the united completion path instead of
trying to do it on every interrupt which isn't necessary.
Only CLKT, ERR and DONE can be cleared that way.
Add the status value to the error value in case of TXW/RXR errors to
distinguish them from the other S_LEN error.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Writing messages larger than the FIFO size results in a hang, rendering
the machine unusable. This is because the RXD status flag is set on the
first interrupt which results in bcm2835_drain_rxfifo() stealing bytes
from the buffer. The controller continues to trigger interrupts waiting
for the missing bytes, but bcm2835_fill_txfifo() has none to give.
In this situation wait_for_completion_timeout() apparently is unable to
stop the madness.
The BCM2835 ARM Peripherals datasheet has this to say about the flags:
TXD: is set when the FIFO has space for at least one byte of data.
RXD: is set when the FIFO contains at least one byte of data.
TXW: is set during a write transfer and the FIFO is less than full.
RXR: is set during a read transfer and the FIFO is or more full.
Implementing the logic from the downstream i2c-bcm2708 driver solved
the hang problem.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Race condition between registering an I2C device driver and
deregistering an I2C adapter device which is assumed to manage that
I2C device may lead to a NULL pointer dereference due to the
uninitialized list head of driver clients.
The root cause of the issue is that the I2C bus may know about the
registered device driver and thus it is matched by bus_for_each_drv(),
but the list of clients is not initialized and commonly it is NULL,
because I2C device drivers define struct i2c_driver as static and
clients field is expected to be initialized by I2C core:
i2c_register_driver() i2c_del_adapter()
driver_register() ...
bus_add_driver() ...
... bus_for_each_drv(..., __process_removed_adapter)
... i2c_do_del_adapter()
... list_for_each_entry_safe(..., &driver->clients, ...)
INIT_LIST_HEAD(&driver->clients);
To solve the problem it is sufficient to do clients list head
initialization before calling driver_register().
The problem was found while using an I2C device driver with a sluggish
registration routine on a bus provided by a physically detachable I2C
master controller, but practically the oops may be reproduced under
the race between arbitraty I2C device driver registration and managing
I2C bus device removal e.g. by unbinding the latter over sysfs:
% echo 21a4000.i2c > /sys/bus/platform/drivers/imx-i2c/unbind
Unable to handle kernel NULL pointer dereference at virtual address 00000000
Internal error: Oops: 17 [#1] SMP ARM
CPU: 2 PID: 533 Comm: sh Not tainted 4.9.0-rc3+ #61
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
task: e5ada400 task.stack: e4936000
PC is at i2c_do_del_adapter+0x20/0xcc
LR is at __process_removed_adapter+0x14/0x1c
Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c5387d Table: 35bd004a DAC: 00000051
Process sh (pid: 533, stack limit = 0xe4936210)
Stack: (0xe4937d28 to 0xe4938000)
Backtrace:
[<c0667be0>] (i2c_do_del_adapter) from [<c0667cc0>] (__process_removed_adapter+0x14/0x1c)
[<c0667cac>] (__process_removed_adapter) from [<c0516998>] (bus_for_each_drv+0x6c/0xa0)
[<c051692c>] (bus_for_each_drv) from [<c06685ec>] (i2c_del_adapter+0xbc/0x284)
[<c0668530>] (i2c_del_adapter) from [<bf0110ec>] (i2c_imx_remove+0x44/0x164 [i2c_imx])
[<bf0110a8>] (i2c_imx_remove [i2c_imx]) from [<c051a838>] (platform_drv_remove+0x2c/0x44)
[<c051a80c>] (platform_drv_remove) from [<c05183d8>] (__device_release_driver+0x90/0x12c)
[<c0518348>] (__device_release_driver) from [<c051849c>] (device_release_driver+0x28/0x34)
[<c0518474>] (device_release_driver) from [<c0517150>] (unbind_store+0x80/0x104)
[<c05170d0>] (unbind_store) from [<c0516520>] (drv_attr_store+0x28/0x34)
[<c05164f8>] (drv_attr_store) from [<c0298acc>] (sysfs_kf_write+0x50/0x54)
[<c0298a7c>] (sysfs_kf_write) from [<c029801c>] (kernfs_fop_write+0x100/0x214)
[<c0297f1c>] (kernfs_fop_write) from [<c0220130>] (__vfs_write+0x34/0x120)
[<c02200fc>] (__vfs_write) from [<c0221088>] (vfs_write+0xa8/0x170)
[<c0220fe0>] (vfs_write) from [<c0221e74>] (SyS_write+0x4c/0xa8)
[<c0221e28>] (SyS_write) from [<c0108a20>] (ret_fast_syscall+0x0/0x1c)
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Some SoC might load the GPIO driver after the I2C driver and
using the I2C bus recovery mechanism via GPIOs. In this case
it is crucial to defer probing if the GPIO request functions
do so, otherwise the I2C driver gets loaded without recovery
mechanisms enabled.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
I2C DesignWare may abort transfer with arbitration lost if I2C slave pulls
SDA down quickly after falling edge of SCL. Reason for this is unknown but
after trial and error it was found this can be avoided by enabling non-zero
SDA RX hold time for the receiver.
By the specification SDA RX hold time extends incoming SDA low to high
transition by n * ic_clk cycles but only when SCL is high. However it
seems to help avoid above faulty arbitration lost error.
Bits 23:16 in IC_SDA_HOLD register define the SDA RX hold time for the
receiver. Be conservative and enable 1 ic_clk cycle long hold time in
case boot firmware hasn't set it up.
Reported-by: Jukka Laitinen <jukka.laitinen@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jukka Laitinen <jukka.laitinen@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Starting with the 8-Series/C220 PCH (Lynx Point), the SMBus
controller includes a SPD EEPROM protection mechanism. Once the SPD
Write Disable bit is set, only reads are allowed to slave addresses
0x50-0x57.
However the legacy implementation of I2C Block Read since the ICH5
looks like a write, and is therefore blocked by the SPD protection
mechanism. This causes the eeprom and at24 drivers to fail.
So assume that I2C Block Read is implemented as an actual read on
these chipsets. I tested it on my Q87 chipset and it seems to work
just fine.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
[wsa: rebased to v4.9-rc2]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
SMBus block command uses the first byte of buffer for the data length.
The dma_buffer should be increased by 1 to avoid the overrun issue.
Reported-by: Phil Endecott <phil_gjouf_endecott@chezphil.org>
Signed-off-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c controller used by Freescales iMX processors is the same
hardware module used on Freescales ColdFire family of processors.
We can use the existing i2c-imx driver on ColdFire family members.
Modify the configuration to allow it to be selected when compiling
for ColdFire targets.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Instantiated I2C device nodes are marked with OF_POPULATE. This was
introduced in 4f001fd301. On unloading, loaded device nodes will of
course be unmarked. The problem are nodes that fail during
initialisation: If a node fails, it won't be unloaded and hence not be
unmarked.
If a I2C driver module is unloaded and reloaded, it will skip nodes that
failed before.
Skip device nodes that are already populated and mark them only in case
of success.
Fixes: 4f001fd301 ("i2c: Mark instantiated device nodes with OF_POPULATE")
Signed-off-by: Ralf Ramsauer <ralf@ramses-pyramidenbau.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
[wsa: use 14-digit commit sha]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
We found a bug that i2c transfer sometimes failed on 3066a board with
stabel-4.8, the con register would be updated by uninitialized tuning
value, it made the i2c transfer failed.
So give the tuning value to be zero during rk3x_i2c_v0_calc_timings.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
This driver should be buildable with ARCH_HISI,
because some of other HiSilicon SoCs also use it.
Signed-off-by: Ruqiang Ju <juruqiang@huawei.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This includes the device tree binding and I2C core changes to support
the i2c-bus subnode that I2C masters can use to describe their slaves
in a separate namespace and therefore avoid clashing with potentially
other subnodes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=+0Q/
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.8-i2c' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into i2c/for-next
[wsa: fell through the cracks, applied to 4.9 now]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c: 'i2c-bus' node support for v4.8-rc1
This includes the device tree binding and I2C core changes to support
the i2c-bus subnode that I2C masters can use to describe their slaves
in a separate namespace and therefore avoid clashing with potentially
other subnodes.
Pull i2c updates from Wolfram Sang:
"Here is the 4.9 pull request from I2C including:
- centralized error messages when registering to the core
- improved lockdep annotations to prevent false positives
- DT support for muxes, gates, and arbitrators
- bus speeds can now be obtained from ACPI
- i2c-octeon got refactored and now supports ThunderX SoCs, too
- i2c-tegra and i2c-designware got a bigger bunch of updates
- a couple of standard driver fixes and improvements"
* 'i2c/for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (71 commits)
i2c: axxia: disable clks in case of failure in probe
i2c: octeon: thunderx: Limit register access retries
i2c: uniphier-f: fix misdetection of incomplete STOP condition
gpio: pca953x: variable 'id' was used twice
i2c: i801: Add support for Kaby Lake PCH-H
gpio: pca953x: fix an incorrect lockdep warning
i2c: add a warning to i2c_adapter_depth()
lockdep: make MAX_LOCKDEP_SUBCLASSES unconditionally visible
i2c: export i2c_adapter_depth()
i2c: rk3x: Fix variable 'min_total_ns' unused warning
i2c: rk3x: Fix sparse warning
i2c / ACPI: Do not touch an I2C device if it belongs to another adapter
i2c: octeon: Fix high-level controller status check
i2c: octeon: Avoid sending STOP during recovery
i2c: octeon: Fix set SCL recovery function
i2c: rcar: add support for r8a7796 (R-Car M3-W)
i2c: imx: make bus recovery through pinctrl optional
i2c: meson: add gxbb compatible string
i2c: uniphier-f: set the adapter to master mode when probing
i2c: uniphier-f: avoid WARN_ON() of clk_disable() in failure path
...
* acpi-wdat:
watchdog: wdat_wdt: Fix warning for using 0 as NULL
watchdog: wdat_wdt: fix return value check in wdat_wdt_probe()
platform/x86: intel_pmc_ipc: Do not create iTCO watchdog when WDAT table exists
i2c: i801: Do not create iTCO watchdog when WDAT table exists
mfd: lpc_ich: Do not create iTCO watchdog when WDAT table exists
ACPI / watchdog: Add support for WDAT hardware watchdog
* acpi-ec:
ACPI / EC: Fix issues related to boot_ec
ACPI / EC: Fix a gap that ECDT EC cannot handle EC events
ACPI / EC: Fix a memory leakage issue in acpi_ec_add()
ACPI / EC: Cleanup first_ec/boot_ec code
ACPI / EC: Enable event freeze mode to improve event handling for suspend process
ACPI / EC: Add PM operations to improve event handling for suspend process
ACPI / EC: Add PM operations to improve event handling for resume process
ACPI / EC: Fix an issue that SCI_EVT cannot be detected after event is enabled
ACPI / EC: Add EC_FLAGS_QUERY_ENABLED to reveal a hidden logic
ACPI / EC: Add PM operations for suspend/resume noirq stage
ACPI WDAT table is the preferred way to use hardware watchdog over the
native iTCO_wdt. Windows only uses this table for its hardware watchdog
implementation so we should be relatively safe to trust it has been
validated by OEMs
Prevent iTCO watchdog creation if we detect that there is ACPI WDAT table.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
axxia_i2c_probe() does not disable clock in case of failure
in i2c_add_adapter(). Also it ignores returned value from
clk_prepare_enable().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Do not infinitely retry register readq and writeq operations
in order to not lock up the CPU in case the TWSI gets stuck.
Return -ETIMEDOUT in case of a failed data read. For all other
cases just return so subsequent operations will fail.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently, the status register FI2C_SR is checked immediately after
a STOP condition is issued in case of the deferred STOP condition.
It takes typically 5-10 usec until the corresponding bits in the
register are set, so the error check for "stop condition was not
completed" is very likely to be false positive.
Add wait code to relax the status register check.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Intel Kaby Lake PCH-H has the same legacy SMBus host controller than Intel
Sunrisepoint PCH. It also has same iTCO watchdog on the bus.
Add Kaby Lake PCH-H PCI ID to the list of supported devices.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This routine is only used together with lockdep for nested locking.
The number of lock subclasses is limited to 8 as defined in lockdep.h
Emit a warning if the adapter depth exceeds the maximum number of
lockdep subclasses.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Peter Rosin <peda@axentia.se>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For crazy setups in which an i2c gpio expander is behind an i2c gpio
multiplexer controlled by a gpio provided a second expander using the
same device driver we need to explicitly tell lockdep how to handle
nested locking.
Export i2c_adapter_depth() as public API to be reused outside of i2c
core code.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Peter Rosin <peda@axentia.se>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the i2c device is already runtime suspended, if qup_i2c_suspend is
executed during suspend-to-idle or suspend-to-ram it will result in the
following splat:
WARNING: CPU: 3 PID: 1593 at drivers/clk/clk.c:476 clk_core_unprepare+0x80/0x90
Modules linked in:
CPU: 3 PID: 1593 Comm: bash Tainted: G W 4.8.0-rc3 #14
Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC (DT)
PC is at clk_core_unprepare+0x80/0x90
LR is at clk_unprepare+0x28/0x40
pc : [<ffff0000086eecf0>] lr : [<ffff0000086f0c58>] pstate: 60000145
Call trace:
clk_core_unprepare+0x80/0x90
qup_i2c_disable_clocks+0x2c/0x68
qup_i2c_suspend+0x10/0x20
platform_pm_suspend+0x24/0x68
...
This patch fixes the issue by executing qup_i2c_pm_suspend_runtime
conditionally in qup_i2c_suspend.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
This patch fixs the following warning:
drivers/i2c/busses/i2c-rk3x.c: In function 'rk3x_i2c_v1_calc_timings':
drivers/i2c/busses/i2c-rk3x.c:745:41: warning: variable 'min_total_ns' set but not used [-Wunused-but-set-variable]
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch fixes the following sparse warning:
drivers/i2c/busses/i2c-rk3x.c:888:17: warning: cast truncates bits from constant value (ffffffffff00 becomes ffffff00)
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When enumerating I2C devices connected to an I2C adapter we scan the whole
namespace (as it is possible to have devices anywhere in that namespace,
not just below the I2C adapter device) and add each found device to the I2C
bus in question.
Now after commit 525e6fabea ("i2c / ACPI: add support for ACPI
reconfigure notifications") checking of the adapter handle to the one found
in the I2cSerialBus() resource was moved to happen after resources of the
I2C device has been parsed. This means that if the I2cSerialBus() resource
points to an adapter that does not exists in the system we still parse
those resources. This is problematic in particular because
acpi_dev_resource_interrupt() tries to configure GSI if the device also has
an Interrupt() resource. Failing to do that results errrors like this to be
printed on the console:
[ 10.409490] ERROR: Unable to locate IOAPIC for GSI 37
To fix this we pass the I2C adapter to i2c_acpi_get_info() and make sure
the handle matches the one in the I2cSerialBus() resource before doing
anything else to the device.
Reported-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The cached value of the last selected channel prevents retries on the
next call, even on failure to update the selected channel. Fix that.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
In case the high-level controller (HLC) is used the status code is
reported at a different location. Check that location after HLC
write operations if the ready bit is not set and return an appropriate
error code instead of always returning -EAGAIN.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Due to a bug in the ThunderX I2C hardware sending STOP during
a recovery attempt could lock up the hardware. To work around
this problem do not send STOP at the beginning of the recovery
but use the override registers to bring the TWSI including
the high-level controller out of the bad state.
Signed-off-by: Dmitry Bazhenov <dmitry.bazhenov@auriga.com>
Signed-off-by: Jan Glauber <jglauber@cavium.com>
[Changed commit message]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The set SCL recovery function unconditionally pulls the SCL line low.
Only pull SCL line low according to val parameter.
Signed-off-by: Dmitry Bazhenov <dmitry.bazhenov@auriga.com>
Signed-off-by: Jan Glauber <jglauber@cavium.com>
[Changed commit message]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
the eg20t driver call request_irq() function before the pch_base_address,
base address of i2c controller's register, is assigned an effective value.
there is one possible scenario that an interrupt which isn't inside eg20t
arrives immediately after request_irq() is executed when i2c controller
shares an interrupt number with others. since the interrupt handler
pch_i2c_handler() has already active as shared action, it will be called
and read its own register to determine if this interrupt is from itself.
At that moment, since base address of i2c registers is not remapped
in kernel space yet,so the INT handler will access an illegal address
and then a error occurs.
Signed-off-by: Yadi.hu <yadi.hu@windriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Since commit 1c4b6c3bcf ("i2c: imx: implement bus recovery") the
driver starts to use gpio/pinctrl to support optional bus recovery
feature. But pinctrl is not always usable. There are platforms such
as ls1021a and ls1043a that don't support pinctrl, and it could just
be broken due to old/broken device tree. The patch makes it really
optional that the probe function won't bailout on pinctrl problems
instead it just disables bus recovery and prints out notification when
there is problem with pinctrl. Since pinctrl is only used by bus
recovery in this driver, move pinctrl initialization into bus recovery
init function to prevent confusion.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Paul Gortmaker