Commit Graph

696 Commits

Author SHA1 Message Date
Anton Vorontsov 8b77aeb4f5 powerpc/83xx: add DS1374 RTC support for the MPC837xE-MDS boards
The RTC is sitting on the I2C1 bus at address 0x68. RTC interrupt signal
is connected to the IPIC's EXT3 interrupt line.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-10-13 11:09:59 -05:00
John Rigby 35225802e2 powerpc/5121: Add PCI support.
Uses mpc83xx_add_bridge in fsl_pci.c

Adds second register tuple to pci node register property
as done for 83xx device trees in a previous patch.

Signed-off-by: John Rigby <jrigby@freescale.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-10-13 11:09:58 -05:00
John Rigby 5b70a09705 powerpc: 83xx: pci: Remove need for get_immrbase from mpc83xx_add_bridge.
Modify mpc83xx_add_bridge to get config space register base address from
the device tree instead of immr + hardcoded offset.

83xx pci nodes have this change:
    register properties now contain two address length tuples:
	First is the pci bridge register base, this has always been there.
	Second is the config base, this is new.

This is documented in dts-bindings/fsl/83xx-512x-pci.txt

The changes accomplish these things:
    mpc83xx_add_bridge no longer needs to call get_immrbase
    it uses hard coded addresses if the second register value is missing

Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-10-13 11:09:58 -05:00
Martyn Welch 3a47024791 powerpc: GE Fanuc's FPGA based PIC controller on the SBC610
Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC MPC8641D).

A number of MPC8641D based route interrupts for on-board interrupts through
a FPGA based interrupt controller, which is chained with the
MPC8641D's mpic. This patch provides a basic driver to allow basic routing
of interrupts to the mpic.

Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-10-13 11:09:57 -05:00
Kumar Gala 92ae954046 powerpc/85xx: Wire up RTC interrupt on MPC8536DS
Add interrupt info to the MPC8536DS .dts for the RTC

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-10-13 11:09:57 -05:00
Paul Mackerras 91a0030295 powerpc: Sync RPA note in zImage with kernel's RPA note
Commit 9b09c6d909 ("powerpc: Change the
default link address for pSeries zImage kernels") changed the
real-base value in the CHRP note added by the addnote program from
12MB to 32MB to give more space for Open Firmware to load the zImage.
(The real-base value says where we want OF to position itself in
memory.)  However, this change was ineffective on most pSeries
machines, because the RPA note added by addnote has the "ignore me"
flag set to 1.  This was intended to tell OF to ignore just the RPA
note, but has the side effect of also making OF ignore the CHRP note
(at least on most pSeries machines).

To solve this we have to set the "ignore me" flag to 0 in the RPA
note.  (We can't just omit the RPA note because that is equivalent to
having an RPA note with default values, and the default values are not
what we want.)  However, then we have to make sure the values in the
zImage's RPA note match up with the values that the kernel supplies
later in prom_init.c with either the ibm,client-architecture-support
call or the process-elf-header call in prom_send_capabilities().

So this sets the "ignore me" flag in the RPA note in addnote to 0, and
adjusts the RPA note values in addnote.c and in prom_init.c to be
consistent with each other and with the values in ibm_architecture_vec.

However, since the wrapper is independent of the kernel, this doesn't
ensure that the notes will stay consistent.  To ensure that, this adds
code to addnote.c so that it can extract the kernel's RPA note from
the kernel binary and put that in the zImage.  To that end, we put the
kernel's fake ELF header (which contains the kernel's RPA note) into
its own section, and arrange for wrapper to pull out that section with
objcopy and pass it to addnote, which then extracts the RPA note from
it and transfers it to the zImage.

Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2008-10-10 15:55:19 +11:00
Benjamin Herrenschmidt fa6428ebfa Merge commit 'jwb/jwb-next' 2008-10-07 11:15:07 +11:00
Victor Gallardo e9ee2924dd powerpc/44x: Add AMCC Arches DTS
Basic functionality for the AMCC Arches eval Board.

Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-10-02 13:08:14 -04:00
David Gibson ad611045ce powerpc: Fix PCI in Holly device tree
The PCI bridge on the Holly board is incorrectly represented in the
device tree.  The current device tree node for the PCI bridge sits
under the tsi-bridge node.  That's not obviously wrong, but the PCI
bridge translates some PCI spaces into CPU address ranges which were
not translated by the "ranges" property in tsi-bridge node.

We used to get away with this problem because the PCI bridge discovery
code was also buggy, assuming incorrectly that PCI host bridge nodes
were always directly under the root bus and treating the translated
addresses as raw CPU addresses, rather than parent bus addresses.
This has since been fixed, thus breaking Holly.

This could be fixed by adding extra translations to the tsi-bridge
node, but this patch instead moves the Holly PCI bridge out of the
tsi-bridge node to the root bus.  This makes the tsi-bridge node
represent only the built-in IO devices in the bridge, with a
more-or-less contiguous address range.  This is the same convention
used on Freescale SoC chips, where the "soc" node represents only the
IMMR region, and the PCI and other bus bridges are separate nodes
under the root bus.

Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2008-09-30 13:25:05 +10:00
Kumar Gala aeb42762b8 powerpc/83xx: Add missing cell-index to dma-channel device nodes
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-09-23 22:05:10 -05:00
Paul Mackerras 1afb7f809b Merge branch 'powerpc-next' of master.kernel.org:/pub/scm/linux/kernel/git/galak/powerpc 2008-09-21 18:18:21 -05:00
Paul Mackerras ff4be78bb7 Merge branch 'next' of ssh://master.kernel.org/pub/scm/linux/kernel/git/jwboyer/powerpc-4xx 2008-09-21 18:17:25 -05:00
Timur Tabi c2fe59444e powerpc: add SSI-to-DMA properties to Freescale MPC8610 HPCD device tree
Add the fsl,playback-dma and fsl,capture-dma properties to the Freescale
MPC8610 HPCD device tree.  These properties connect the SSI nodes to the
DMA nodes for the DMA channels that the SSI should use.  Also update the
ssi.txt documentation.

These properties will be needed when the ASoC V2 version of the Freescale
MPC8610 device drivers are merged into the mainline.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-09-17 15:01:20 -05:00
Josh Boyer 32dde0f975 powerpc: Holly board needs dtbImage target
One of the changes in the bootwrapper makefile introduced the dtbImage
targets for boards that need a simple zImage with a DTB embedded in
them (595be948cc, "[POWERPC]
bootwrapper: Build multiple cuImages").  When this was done, it broke
booting on the Holly board as the zImage.holly wrapper did not get the
DTB embedded properly.

This changes the target for the Holly board to a dtbImage so that the
wrapper includes the vmlinux, wrapper bits, and DTB.

Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-09-17 09:14:42 -07:00
Timur Tabi 612f9d338a powerpc: Fix interrupt values for DMA2 in MPC8610 HPCD device tree
For Freescale 8xxx devices that use an MPIC, the interrupt numbers in
the device tree must be 16 greater than the values documented in the
reference manual.  In these chips, the MPIC is wired to use the first
16 numbers for external interrupts, but the documentation numbers
internal interrupts from 0.

In the MPC8610 HPCD device tree, the interrupt properties for the DMA
channels for DMA2 were not the adjusted values.  This fixes that.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-09-16 14:40:05 -07:00
Martyn Welch 54508214cf powerpc: Board support for GE Fanuc SBC610
Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC
MPC8641D).

This is the basic board support for GE Fanuc's SBC610, a 6U single board
computer, based on Freescale's MPC8641D.

Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-09-16 10:17:14 -05:00
Anton Vorontsov 307db95882 powerpc/83xx: mpc836x_mds: add support for the nor flash
This patch adds the localbus node, moves the bcsr node into the
localbus node, and adds the flash node.

Also enable MTD support in the defconfig.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-09-16 10:01:34 -05:00
Heiko Schocher 637166337c powerpc: Add support for mpc8247 based board MGCOGE from keymile.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-09-16 10:01:32 -05:00
Heiko Schocher e14d4af0c8 powerpc: Add support for the MPC852 based mgsuvd board from keymile.
Supported SMC1 (serial console), SCC3 Ethernet (10Mbps hdx).

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-09-16 10:01:30 -05:00
Paul Mackerras 549e8152de powerpc: Make the 64-bit kernel as a position-independent executable
This implements CONFIG_RELOCATABLE for 64-bit by making the kernel as
a position-independent executable (PIE) when it is set.  This involves
processing the dynamic relocations in the image in the early stages of
booting, even if the kernel is being run at the address it is linked at,
since the linker does not necessarily fill in words in the image for
which there are dynamic relocations.  (In fact the linker does fill in
such words for 64-bit executables, though not for 32-bit executables,
so in principle we could avoid calling relocate() entirely when we're
running a 64-bit kernel at the linked address.)

The dynamic relocations are processed by a new function relocate(addr),
where the addr parameter is the virtual address where the image will be
run.  In fact we call it twice; once before calling prom_init, and again
when starting the main kernel.  This means that reloc_offset() returns
0 in prom_init (since it has been relocated to the address it is running
at), which necessitated a few adjustments.

This also changes __va and __pa to use an equivalent definition that is
simpler.  With the relocatable kernel, PAGE_OFFSET and MEMORY_START are
constants (for 64-bit) whereas PHYSICAL_START is a variable (and
KERNELBASE ideally should be too, but isn't yet).

With this, relocatable kernels still copy themselves down to physical
address 0 and run there.

Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-09-15 11:08:38 -07:00
Paul Mackerras 7e392f8c29 Merge branch 'linux-2.6' 2008-09-10 11:36:13 +10:00
Matthias Fuchs 423da26997 powerpc/44x: Add hwmon support to Sequoia device tree
This patch adds support for the AD7414 temperature sensor
on Sequoia PPC440EPx board.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-09-09 08:18:01 -04:00
Hugh Dickins 4ff23fa930 powerpc: Fix rare boot build breakage
A make -j20 powerpc kernel build broke a couple of months ago saying:
In file included from arch/powerpc/boot/gunzip_util.h:13,
                 from arch/powerpc/boot/prpmc2800.c:21:
arch/powerpc/boot/zlib.h:85: error: expected ‘:’, ‘,’, ‘;’, ‘}’ or ‘__attribute__’ before ‘*’ token
arch/powerpc/boot/zlib.h:630: warning: type defaults to ‘int’ in declaration of ‘Byte’
arch/powerpc/boot/zlib.h:630: error: expected ‘;’, ‘,’ or ‘)’ before ‘*’ token

It happened again yesterday: too rare for me to confirm the fix, but
it looks like the list of dependants on gunzip_util.h was incomplete.

Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-09-08 15:55:35 +10:00
Josh Boyer 38d56f1677 powerpc/44x: Add explicit Yosemite support
Add the Yosemite board to the explicitly supported list for ppc44x_simple
boards and remove the compatible entry for bamboo from the DTS file.

Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-08-28 09:12:47 -04:00
Josh Boyer ded563cf45 powerpc/44x: Add explicit support for AMCC Glacier
Add explicit support for the AMCC Glacier eval board to Kconfig and the
ppc44x_simple file.  Also removes the cayonlands compatible entry from the
DTS file.

Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-08-28 09:10:35 -04:00
Scott Wood 8dd217b27e powerpc: Add cuImage.mpc866ads to the bootwrapper as a cuboot-8xx target
This patch fixes the following build error with mpc866_ads_defconfig:

<--  snip  -->

...
  WRAP    arch/powerpc/boot/cuImage.mpc866ads
powerpc64-linux-ld: arch/powerpc/boot/cuboot-mpc866ads.o: No such file: No such file or directory
make[2]: *** [arch/powerpc/boot/cuImage.mpc866ads] Error 1

<--  snip  -->

Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-08-21 00:37:04 -05:00
Wolfgang Grandegger d27a736c7a powerpc/85xx: TQM8548: DTS file fixes and cleanup
Due to the missing compatible property for the SOC, the MPC I2C buses are
not found any more. This patch fixes this issue. Furthermore it corrects
the name of the SOC node and adds the missing I2C node for the RTC.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-08-20 23:56:30 -05:00
Kumar Gala ba1616d921 powerpc: Fix whitespace merge in mpc8641 hpcn device tree
When we coverted the .dts to v1 we lost a space between the irq
and its polarity/sense information.  This causes a bit of chaos
as the reset of the blob is off by one cell.

This was noticed by booting and getting errors w/ATA due to
lock of interrupts.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-08-20 23:26:02 -05:00
David Gibson ed95d7450d powerpc: Update in-kernel dtc and libfdt to version 1.2.0
Some time ago, a copies of the upstream dtc and libfdt sources were
included in the kernel tree to avoid having these as external
dependencies for building the kernel.  Since then development on the
upstream dtc and libfdt has continued.  This updates the in-kernel
versions to match the recently released upstream dtc version 1.2.0.
This includes a number of bugfixes, many cleanups and a few new
features.

Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-08-20 16:34:58 +10:00
Linus Torvalds e2205a156f Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
  powerpc: Remove include/linux/harrier_defs.h
  powerpc: Do not ignore arch/powerpc/include
  powerpc: Delete completed "ppc removal" task from feature removal file
  powerpc/mm: Fix attribute confusion with htab_bolt_mapping()
  powerpc/pci: Don't keep ISA memory hole resources in the tree
  powerpc: Zero fill the return values of rtas argument buffer
  powerpc/4xx: Update defconfig files for 2.6.27-rc1
  powerpc/44x: Incorrect NOR offset in Warp DTS
  powerpc/44x: Warp DTS changes for board updates
  powerpc/4xx: Cleanup Warp for i2c driver changes.
  powerpc/44x: Adjust warp-nand resource end address
2008-08-11 10:40:28 -07:00
Anton Vorontsov 775587b6d7 powerpc: 86xx: mpc8610_hpcd: add watchdog node
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-08-05 14:33:46 -07:00
Sean MacLennan 929badad62 powerpc/44x: Incorrect NOR offset in Warp DTS
FPGA offset in NOR flash was converted incorrectly when switching from
64M to 4M flash.

Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-08-04 21:42:07 -04:00
Sean MacLennan 1d555cf168 powerpc/44x: Warp DTS changes for board updates
Added support for the new at24 eeprom driver.
Documented a new fpga section, the DMA scatter gather list.
Removed index from i2c. No longer needed.
Fixed the leds section.

Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-08-04 21:42:07 -04:00
Stephen Rothwell b8b572e101 powerpc: Move include files to arch/powerpc/include/asm
from include/asm-powerpc.  This is the result of a

mkdir arch/powerpc/include/asm
git mv include/asm-powerpc/* arch/powerpc/include/asm

Followed by a few documentation/comment fixups and a couple of places
where <asm-powepc/...> was being used explicitly.  Of the latter only
one was outside the arch code and it is a driver only built for powerpc.

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-08-04 12:02:00 +10:00
Kim Phillips cf0d19fb30 powerpc/fsl: proliferate simple-bus compatibility to soc nodes
add simple-bus compatible property to soc nodes for 83xx/85xx platforms
that were missing them.  Add same to platform probe code.

This fixes SoC device drivers (such as talitos) to succeed in matching
devices present in the soc node.

also update mpc836x_rdk dts to new SEC bindings (overlooked in commit
3fd4473: powerpc/fsl: update crypto node definition and device tree
instances).

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-07-29 17:48:35 -05:00
Adrian Bunk 542a3a3bc9 powerpc/boot: Change spaces to tabs
For C code spaces versus tabs is just a religious issue,
but for Makefiles it actually matters.

This patch fixes he following errors:
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/powerpc/boot/Makefile:166: *** missing separator.  Stop.
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/powerpc/boot/Makefile:171: *** missing separator.  Stop.

Since this was inside an ifdef DTC_GENPARSER it was not a problem unless
someone wanted to regenerate the shipped generated files.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2008-07-22 10:39:35 +10:00
Anton Vorontsov a47fda9307 powerpc/86xx: mpc8610_hpcd - add support for ULI RTC
The ULI "Super South Bridge" contains ISA bridge to the legacy
devices, such as Super IO mouse/keyboard/floppy disk controllers,
parallel port, i8259 interrupt controller and so on.

i8259 is disabled on the MPC8610HPCD, and other peripherals are not
traced out. So we use only RTC.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-07-16 17:57:43 -05:00
Paul Gortmaker 36aa7965d8 powerpc/mpc7448: add alias list to DTS, clean out old chosen node
The mpc7448hpc2 board doesn't have an alias block like
most of the other modern eval boards have.  We need this
block in order to have u-boot be able to make use of the
CONFIG_OF_STDOUT_VIA_ALIAS (vs. having a hard coded node)
in the future.

Also remove the old, redundant chosen node.  Of all the modern
Freescale eval boards (incl. 83xx, 85xx, 86xx) this is the only
one which still has it.  Its presence also breaks with some older
versions of u-boot, like 1.3.1 -- which try and insert a
second chosen node.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-07-16 17:57:33 -05:00
Scott Wood 574366128d powerpc/mpc8313erdb: Add power management to the device tree.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-07-16 17:57:31 -05:00
Benjamin Herrenschmidt 5b0504c0d7 Merge commit 'gcl/gcl-next' 2008-07-15 11:55:27 +10:00
Benjamin Herrenschmidt 930074b6b9 Merge commit 'jwb/jwb-next' 2008-07-15 11:54:57 +10:00
Kim Phillips 3fd44736db powerpc/fsl: update crypto node definition and device tree instances
delete obsolete device-type property, delete model property
(use compatible property instead), prepend "fsl," to Freescale
specific properties. Add nodes to device trees that are missing them,
and fix broken property values in other trees.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-07-14 07:55:47 -05:00
Jochen Friedrich a5d28c8e64 powerpc/CPM: Add i2c pins to dts and board setup
Initialize I2C pins on boards with CPM1/CPM2 controllers and document the
i2c bus in booting-without-of.

The boards don't have any I2C chips connected to the I2C bus, so unless
some external chips are connected to the boards, this code is just an
example of setting everything else up.

Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-07-14 07:55:39 -05:00
Kumar Gala 2f3804edf9 powerpc/85xx: Add support for MPC8536DS
Add support for the MPC8536 process and MPC8536DS reference board.  The
MPC8536 is an e500v2 based SoC which eTSEC, USB, SATA, PCI, and PCIe.

The USB and SATA IP blocks are similiar to those on the PQ2 Pro SoCs and
thus use the same drivers.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-07-14 07:55:37 -05:00
Wolfgang Grandegger a3083220c0 powerpc/85xx: TQM8548: add missing support for RTC and LM75
It adds the missing RTC node to tqm8548.dts and enables support for
I2C, DS1307 and LM75 in the default configuration.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-07-14 07:55:34 -05:00
Anton Vorontsov deabeabf0b powerpc/86xx: mpc8610_hpcd: fix interrupt trigger type for ULi IDE
i8259 PIC is disabled on MPC8610HPCD, and ULi IDE is configured to use
PCI sideband interrupt that is specified in the device tree.

Current HPCD's device tree specify that IDE interrupt is low to high
sensitive, but in practice ULi IDE throws active-high interrupts (not
active-low as all normal PCI devices).

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-07-14 07:55:32 -05:00
Kumar Gala 0fe9b1ea60 powerpc/85xx: Fix KSI8560 .dts
Rename MPIC label to mpic to match all other 85xx .dts and to fix compile
issue introduced by addition of the DMA node.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-07-14 07:55:29 -05:00
Benjamin Herrenschmidt 11c2d8174e Merge commit 'origin/HEAD' into test-merge
Manual fixup of include/asm-powerpc/pgtable-ppc64.h
2008-07-14 14:29:49 +10:00
John Rigby 4df64c3e58 powerpc/mpc5121: Update device tree for MPC5121ADS evaluation board
Current device tree is only bare bones.  This patch adds nodes to make
it a complete tree for the MPC5121ads.

Added nodes include:
    mbx      - opengl coprocessor
    nfc      - nand flash controller
    cpld-pic - on board cpld
    rtc
    clock    - clock control
    pmc      - power management control
    gpio
    mscan    - can module
    i2c
    axe      - audio coprocessor
    display  - display interface unit
    mdio
    ethernet
    usb
    ioctl    - pin config
    pata
    ac97     - PSC configured as AC97
    pscfifo  - psc fifo configuration
    dma
    pci

Fix typo in header changing MDS to ADS.

Add a compatible property of the form "fsl,mpc5121-..."
to nodes missing one.

Changed localbus compatible to fsl,mpc5121-localbus, this does
not break anything because the only code that uses it finds it
via the node name, not compatible.

Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-07-12 12:10:54 -06:00
Wolfgang Grandegger b0852cb884 powerpc/mpc5200: add missing MSCAN FDT nodes for TQM52xx
This patch adds the still missing FDT nodes for the MSCAN devices for
the TQM52xx modules.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-07-12 12:10:52 -06:00
Grant Likely 9fde9bdd30 powerpc/440: Convert Virtex ML507 device tree to dts-v1
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-07-09 10:56:11 -06:00
Grant Likely c356aa456e powerpc/bootwrapper: Allow user to specify additional default targets
It is inconvenient to add additional default targets to the bootwrapper
Makefile for each new board supported which just needs a different dts
file.  This change allows the defconfig to specify additional build
targets.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-07-09 09:41:52 -06:00
Grant Erickson 05781ccd74 ibm_newemac: Parameterize EMAC Multicast Match Handling
Various instances of the EMAC core have varying: 1) number of address
match slots, 2) width of the registers for handling address match slots,
3) number of registers for handling address match slots and 4) base
offset for those registers.

As the driver stands today, it assumes that all EMACs have 4 IAHT and
GAHT 32-bit registers, starting at offset 0x30 from the register base,
with only 16-bits of each used for a total of 64 match slots.

The 405EX(r) and 460EX now use the EMAC4SYNC core rather than the EMAC4
core. This core has 8 IAHT and GAHT registers, starting at offset 0x80
from the register base, with ALL 32-bits of each used for a total of
256 match slots.

This adds a new compatible device tree entry "emac4sync" and a new,
related feature flag "EMAC_FTR_EMAC4SYNC" along with a series of macros
and inlines which supply the appropriate parameterized value based on
the presence or absence of the EMAC4SYNC feature.

The code has further been reworked where appropriate to use those macros
and inlines.

In addition, the register size passed to ioremap is now taken from the
device tree:

	c4 for EMAC4SYNC cores
	74 for EMAC4 cores
	70 for EMAC cores

rather than sizeof (emac_regs).

Finally, the device trees have been updated with the appropriate compatible
entries and resource sizes.

This has been tested on an AMCC Haleakala board such that: 1) inbound
ICMP requests to 'haleakala.local' via MDNS from both Mac OS X 10.4.11
and Ubuntu 8.04 systems as well as 2) outbound ICMP requests from
'haleakala.local' to those same systems in the '.local' domain via MDNS
now work.

Signed-off-by: Grant Erickson <gerickson@nuovations.com>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2008-07-09 16:30:46 +10:00
Grant Likely 1d46e379aa powerpc/bootwrapper: add missing bit of simpleImage target
The wrapper script is missing the bits needed for building generic
simpleImage targets (targets which don't depend on any particular
firmware interface and retrieve all their data from the device tree).

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-07-04 00:59:37 -06:00
John Linn d58577d8f3 powerpc/virtex: Fix booting of Xilinx FPGAs with 16550 for 405 and 440
The following changes add processing to initialize the Xilinx 16550 UART
in the boot wrapper for Virtex targets without firmware.  Normally the
boot wrapper assumes that the serial port has already been initialized by
firmware.

The wrapper was also modified to add the 440 build.

Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-07-04 00:58:59 -06:00
John Linn dc568ec490 powerpc/virtex: add dts file for ML507 reference design
This new file adds support for the ML507 reference design.  The ML507
uses the Virtex 5 FXT FPGA which embeds a ppc440 core.

Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-07-04 00:57:59 -06:00
John Linn 5d1a04110b powerpc/bootwrapper: update for initrd with simpleImage
This change to the makefile corrects the build of a simpleImage with initrd.

Signed-off-by: John Linn <john.linn@xilinx>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-07-01 14:17:18 -06:00
Kumar Gala 9d4ae9fc92 powerpc/bootwrapper: Pad .dtb by default
Since most bootloaders or wrappers tend to update or add some information
to the .dtb they a handled they need some working space to do that in.

By default add 1K of padding via a default setting of DTS_FLAGS.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-07-01 11:28:53 +10:00
Tony Breeds 9b09c6d909 powerpc: Change the default link address for pSeries zImage kernels
Currently we set the start of the .text section to be 4Mb for pSeries.
In situations where the zImage is > 8Mb we'll fail to boot (due to
overlapping with OF).  Move .text in a zImage from 4MB to 64MB
(well past OF).

We still will not be able to load large zImage unless we also move OF,
to that end, add a note to the zImage ELF to move OF to 32Mb.  If this
is the very first kernel booted then we'll need to move OF manually by
setting real-base.

Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-07-01 11:28:32 +10:00
Paul Mackerras e9a4b6a3f6 Merge branch 'linux-2.6' 2008-06-30 10:16:50 +10:00
Paul Mackerras 441dbb500b Merge branch 'next' of master.kernel.org:/pub/scm/linux/kernel/git/jwboyer/powerpc-4xx 2008-06-30 09:57:05 +10:00
Kumar Gala dee805532a powerpc: Add dma nodes to 83xx, 85xx and 86xx boards
Added DMA nodes for the elo/elo-plus DMA engines.

Renamed the interrupt controller alias in mpc832x_rdb.dts to ipic so that
its the same as all the other boards.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-06-27 16:04:29 -05:00
Kumar Gala 143580ecfb [POWERPC] Fix bootwrapper builds with newer gcc versions
GCC 4.4.x looks to be adding support for generating out-of-line register
saves/restores based on:

http://gcc.gnu.org/ml/gcc-patches/2008-04/msg01678.html

This breaks the bootwrapper as we'd need to link with libgcc to get the
implementation of the register save/restores.

To workaround this issue, we just stole the save/restore code from gcc
and simplified it down for our needs (integer only).

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-06-16 15:00:52 +10:00
Paul Mackerras ecab9ab22a Merge branch 'for-2.6.26' of master.kernel.org:/pub/scm/linux/kernel/git/galak/powerpc into merge 2008-06-16 14:30:47 +10:00
Giuseppe Coviello d2146cb274 powerpc/4xx: Convert Sam440ep DTS to dts-v1
This makes the sam440ep.dts dts-v1 compliant.

Signed-off-by: Giuseppe Coviello <gicoviello@gmail.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-06-11 08:33:59 -04:00
Giuseppe Coviello b6014e15bc powerpc/4xx: Sam440ep support
The Sam440ep is an high customizable general purpose mini-itx board,
based on the AMCC 440EP and with a LatticeXP FPGA onboard.

It's poduced by ACube Systems Srl (Bassano del Grappa, Italy),
http://www.acube-systems.biz.

Signed-off-by: Giuseppe Coviello <gicoviello@gmail.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-06-11 08:32:49 -04:00
Imre Kaloz 887942d7d6 powerpc/4xx: MTD support for the AMCC Taishan Board
Add support for the NOR flash found on the AMCC Taishan Board
and enable MTD support in the defconfig.

Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-06-11 08:03:41 -04:00
Anton Vorontsov b13e930906 powerpc/83xx: new board support: MPC8360E-RDK
This is patch adds board file, device tree, and defconfig for the new
board, made by Freescale Semiconductor Inc. and Logic Product Development.

Currently supported:
1. UEC{1,2,7,4};
2. I2C;
3. SPI;
4. NS16550 serial;
5. PCI and miniPCI;
6. Intel NOR StrataFlash X16 64Mbit PC28F640P30T85;
7. Graphics controller, Fujitsu MB86277.

Not supported in this patch:
1. StMICRO NAND512W3A2BN6E, 512 Mbit (supported with FSL UPM NAND driver);
2. FHCI USB (supported with FHCI driver).
3. QE Serial UCCs (tested to not work with ucc_uart driver, reason
   unknown, yet);
4. ADC AD7843 (tested to work, but support via device tree depends on
   major SPI rework, GPIO API, etc);

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-06-10 11:11:17 -05:00
Wolfgang Grandegger 5399be7f46 powerpc/85xx: add local bus nodes for Flash and CAN to tqm8560.dts
This patch adds local bus nodes for Flash and CAN to the DTS file
of the TQM8560 module (tqm8560.dts).

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-06-10 10:34:37 -05:00
Wolfgang Grandegger 02b8a3d1eb powerpc/85xx: support for the TQM8548 module using the big Flash
Some TQM85xx boards could be equipped with up to 1 GiB (NOR) flash
memory and therefore a modified memory map is required and setup by
the board loader. This patch adds an appropriate DTS file.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-06-10 10:34:28 -05:00
Wolfgang Grandegger 6dd1b64a26 powerpc/85xx: add board support for the TQM8548 modules
This patch adds support for the TQM8548 modules from TQ-Components
GmbH (http://www.tqc.de).

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-06-10 10:33:53 -05:00
Wolfgang Grandegger 4fb035f69e powerpc/85xx: correct vendor prefix in DTS files for TQM85xx modules
Like for the TQM5200, the vendor prefix "tqc," is now used for all
TQM85xx modules from TQ-Components GmbH (http://www.tqc.de) in the
corresponding DTS files.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-06-10 10:33:11 -05:00
Anton Vorontsov f17c63231c [POWERPC] 83xx: MPC837xRDB's VSC7385 ethernet switch isn't on the MDIO bus
MDIO-less PHYs should use CONFIG_FIXED_PHY driver and appropriate
fixed-link property in the device tree.

If not, ethernet will not work:
  e0024520:03 not found
  eth1: Could not attach to PHY
  IP-Config: Failed to open eth1

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-06-10 09:19:26 -05:00
Kumar Gala ad16880daa [POWERPC] 85xx: MPC8548CDS - Fix size of PCIe IO space
Andrew Klossner pointed out the IO space size was in violation of
the alignment requirements for windows on the 85xx.  The size should
have been 1M (to match u-boot).

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-06-09 08:45:07 -05:00
Remi Machet c6ec08e03d powerpc: Boot code for the C2K
Support for the C2K cPCI Single Board Computer from GEFanuc
(PowerPC MPC7448 with a Marvell MV64460 chipset).
All features of the board are not supported yet, but the board
boots, flash works, all Ethernet ports are working and PCI
devices are all found (USB and SATA on PCI1 do not work yet).

Part 2 of 5: support for the board in arch/powerpc/boot.

Signed-off-by: Remi Machet <rmachet@slac.stanford.edu>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-06-09 13:42:25 +10:00
Remi Machet 61586476cd powerpc: DTS file for the C2K
Support for the C2K cPCI Single Board Computer from GEFanuc
(PowerPC MPC7448 with a Marvell MV64460 chipset).
All features of the board are not supported yet, but the board
boots, flash works, all Ethernet ports are working and PCI
devices are all found (USB and SATA on PCI1 do not work yet).

Part 1 of 5: DTS file describing the board peripherals.  As far as I
know all peripherals except the FPGA are listed in there (I did not
include the FPGA because a lot of work is needed there).

Signed-off-by: Remi Machet <rmachet@slac.stanford.edu>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-06-09 13:41:16 +10:00
Paul Mackerras 8a3e1c670e Merge branch 'merge'
Conflicts:

	arch/powerpc/sysdev/fsl_soc.c
2008-06-09 12:19:41 +10:00
Adrian Bunk efa58fbf19 [POWERPC] boot/Makefile CONFIG_ variable fixes
This corrects the names of two CONFIG_ variables.

Note that the CONFIG_MPC86XADS fix uncovers another bug
(with mpc866_ads_defconfig) that will require fixing:

<--  snip  -->

...
arch/powerpc/boot/dtc -O dtb -o arch/powerpc/boot/mpc866ads.dtb -b 0  /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/powerpc/boot/dts/mpc866ads.dts
DTC: dts->dtb  on file "/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/powerpc/boot/dts/mpc866ads.dts"
  WRAP    arch/powerpc/boot/cuImage.mpc866ads
powerpc64-linux-ld: arch/powerpc/boot/cuboot-mpc866ads.o: No such file: No such file or directory
make[2]: *** [arch/powerpc/boot/cuImage.mpc866ads] Error 1

<--  snip  -->

Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-06-09 11:30:15 +10:00
Kumar Gala c054065bc1 [POWERPC] 85xx: Add next-level-cache property
Added next-level-cache to the L1 and a reference to the new L2 label.
This is per the ePAPR 0.94 spec.  Since we are't really dependent on this
today we aren't supporting the "legacy" l2-cache phandle that is specified
in the PPC v2.1 OF Binding spec.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-06-02 14:44:25 -05:00
Kumar Gala acd4b715ec [POWERPC] Cleanup mpic nodes in .dts
Removed clock-frequency, big-endian, and built-in props as they aren't
specified anywhere.  Also added compatible = "chrp,open-pic" in the
places it was missing.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-06-02 14:44:25 -05:00
Bryan O'Donoghue 59d13f9dba [POWERPC] 83xx: Add support for Analogue & Micro ASP837E board
The following adds support for the Analogue & Micro ASP 8347E, running
Redboot.

http://www.analogue-micro.com/ASP8347.html

Signed-off-by: Bryan O'Donoghue <bodonoghue@codehermit.ie>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-06-02 14:44:25 -05:00
Jason Jin 741edc4949 [POWERPC] 85xx: Enable MSI support for 85xxds board
This patch enabled MSI on 8544ds and 8572ds board.
So far only one MSI interrupt can generate on 8544 board.

Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-06-02 14:44:24 -05:00
Jason Jin 0023352f56 [POWERPC] 86xx: Enable MSI support for MPC8610HPCD board
This patch enable the MSI on 8610hpcd board.
Through the msi-available-ranges property, All the 256
msi interrupts can be tested on this board.

Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-06-02 14:44:24 -05:00
Timur Tabi 9c8b28c2ef [POWERPC] Fix DMA nodes in the MPC8610 HPCD device tree
The node for DMA2 in the MPC8610 HPCD device tree has the wrong compatible
properties.  This breaks the DMA driver and the sound driver.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-05-31 17:08:29 +10:00
Sean MacLennan 4ebef31fa6 [POWERPC] PIKA Warp: Update platform code to support Rev B boards
* Switched from 64M NOR/64M NAND to 4M NOR/256M NAND.
* Full DTM support including critical temperature.
* Added POST information.
* Removed LED function, moved to new LED driver.
* Moved ad7414 to new style I2C initialization.

Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-05-29 07:06:56 -05:00
Sean MacLennan 0393cb615f [POWERPC] PIKA Warp: Update DTS to support Rev B boards
* Switched from 64M NOR/64M NAND to 4M NOR/256M NAND.
* Added led entries.
* Added fpga-sd entry.
* Added ad7414 entry.

Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-05-29 07:06:56 -05:00
Josh Boyer 6f031101f5 [POWERPC] 4xx: Fix PCI mem in rainier DTS
This fixes the PCI node in the Rainier to match the spec from AMCC.  A
similar fix was done for 440EPx, which shares the same values as 440GRx.

Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-05-29 07:06:56 -05:00
David Gibson 71f349799b [POWERPC] Convert remaining dts-v0 files to v1
At the moment we have a mixture of left-over version 0 and new-format
version 1 files in arch/powerpc/boot/dts.  This is potentially
confusing to people new to the dts format attempting to figure it out.

So, this patch converts all the as-yet unconverted dts v0 files and
converts them to v1.  They're mechanically-converted, and not hand
tweaked so in some cases they're not 100% in keeping with usual v1
style, but the convertor program does have some heuristics so the
discrepancies aren't too bad.

I have checked that this patch produces no changes to the resulting
dtb binaries.

Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-05-29 07:06:56 -05:00
Paul Mackerras 927c258ac6 Merge branch 'for-2.6.26' of master.kernel.org:/pub/scm/linux/kernel/git/galak/powerpc into merge 2008-05-20 19:46:37 +10:00
Kumar Gala 8939700edc [POWERPC] Fix mpc8377_mds.dts DMA nodes to match spec
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-05-20 00:37:13 -05:00
Kumar Gala 4978757987 [POWERPC] Update arch/powerpc/boot/.gitignore
* Add dtbImage.*
* Added zImage.holly
* Folded zImage.coff.lds into zImage.*lds
* Removed some unused zImage.<foo> ignores

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-05-20 00:35:29 -05:00
Kumar Gala b58a457528 [POWERPC] Remove generated files on make clean
dtbImage.* and several zImage. targets get created but never cleaned up.

Also, moved zImage to the clean-files line associated with all other image
results (was previously duplicated).

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-05-20 00:27:19 -05:00
Josh Boyer 13c501e69c [POWERPC] 4xx: Workaround for CHIP_11 Errata
The PowerPC 440EP, 440GR, 440EPx, and 440GRx chips have an issue that
causes the PLB3-to-PLB4 bridge to wait indefinitely for transaction
requests that cross the end-of-memory-range boundary.  Since the DDR
controller only returns the valid portion of a read request, the bridge
will prevent other PLB masters from completing their transactions.

This implements the recommended workaround for this errata for chips that
use older versions of firmware that do not already handle it.  The last
4KiB of memory are hidden from the kernel to prevent the problem
transactions from occurring.

Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-05-19 09:36:40 -05:00
Jeremy McNicoll bfd123bf91 [POWERPC] 85xx: SBC8548 - Add flash support and HW Rev reporting
The following adds local bus, flash and MTD partition nodes for
sbc8548. As well, a compatible field for the soc node, so that
of_platform_bus_probe() will pick it up.

Something that is provided through this newly added epld node
is the Hardware Revision which is now being utilized.

Signed-off-by: Jeremy McNicoll <jeremy.mcnicoll@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-05-13 08:53:48 -05:00
Zhang Wei 3f346935f4 [POWERPC] 83xx: Enable DMA engine on the MPC8377 MDS board.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Cc: "Nelson, Shannon" <shannon.nelson@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-05-13 08:53:48 -05:00
Anton Vorontsov 34b4a8731f [POWERPC] 86xx: mpc8610_hpcd: add support for NOR and NAND flashes
This patch adds device tree nodes for NOR and NAND flashes and places
board-control node inside the localbus.

defconfig and board file updated appropriately.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-05-13 08:53:48 -05:00
Christian Ehrhardt 78be76476a [POWERPC] 4xx: Fix PCI mem in sequoia DTS
This patch is fixes the sequoia.dts device tree file to use the values defined
in the 440Epx data sheet from AMCC.

That fixes an issue where some devices, including graphics cards, would not
initialize properly because the PCI resource space was not big enough.

Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-05-06 12:37:15 -05:00
Anton Vorontsov e598477a3a [POWERPC] 86xx: mpc8610_hpcd: add support for PCI Express x8 slot
This patch adds pcie node which is resposible for PCI-E x8 slot
functioning. Though, this was tested using only x1 SKY2 NIC.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-05-01 23:01:46 -05:00
Jason Jin aecb2b6eac [POWERPC] 86xx: Fix the wrong serial1 interrupt for 8610 board
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-04-30 05:45:53 -05:00
Grant Likely a2884f37b6 [POWERPC] mpc5200: Switch mpc5200 dts files to dts-v1 format
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-04-29 07:19:07 -06:00
s.hauer@pengutronix.de 106757b38f [POWERPC] mpc5200: add Phytec pcm030 board support
Add board support for the Phytec pcm030 mpc5200b based board. It
does not need any platform specific fixups and as such is handled
as a mpc5200 simple platform.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-04-29 07:17:12 -06:00
Zhang Wei 56fde1ff69 [RAPIDIO] Add RapidIO node into MPC8641HPCN dts file
This adds properties describing the RapidIO controller to the
device-tree source for the MPC8641HPCN board.

Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-04-29 19:40:28 +10:00
York Sun 9b53a9e28a fbdev: powerpc: driver for Freescale 8610 and 5121 DIU
The following features are supported:
plane 0 works as a regular frame buffer, can be accessed by /dev/fb0
plane 1 has two AOIs (area of interest), can be accessed by /dev/fb1 and /dev/fb2
plane 2 has two AOIs, can be accessed by /dev/fb3 and /dev/fb4
Special ioctls support AOIs

All /dev/fb* can be used as regular frame buffer devices, except hardware
change can only be made through /dev/fb0.  Changing pixel clock has no effect
on other fbs.

Limitation of usage of AOIs:
AOIs on the same plane can not be horizonally overlapped
AOIs have horizonal order, i.e. AOI0 should be always on top of AOI1
AOIs can not beyond phisical display area. Application should check AOI geometry
before changing physical resolution on /dev/fb0

required command line parameters to preallocate memory for frame buffer diufb.

optional command line parameters to set modes and monitor
video=fslfb:[resolution][,bpp][,monitor]
Syntax:

Resolution
xres x yres-bpp@refresh_rate, the -bpp and @refresh_rate are optional
eg, 1024x768, 1280x1024, 1280x1024-32, 1280x1024@60, 1280x1024-32@60, 1280x480-32@60

Bpp
bpp=32, bpp=24, or bpp=16

Monitor
monitor=0, monitor=1, monitor=2
0 is DVI
1 is Single link LVDS
2 is Double link LVDS

Note: switching monitor is a board feather, not DIU feather. MPC8610HPCD has three
monitor ports to swtich to. MPC5121ADS doesn't have additional monitor port. So switching
monirot port for MPC5121ADS has no effect.

If compiled as a module, it takes pamameters mode, bpp, monitor with the same syntax above.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:40 -07:00
Kumar Gala f360bf0015 [POWERPC] Add zImage.iseries to arch/powerpc/boot/.gitignore
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-04-25 09:48:13 +10:00
Grant Likely b9e4f17666 [POWERPC] bootwrapper: fix build error on virtex405-head.S
virtex405-head.S is an assembler file, not a C file; therefore BOOTAFLAGS
is the correct place to set the needed -mcpu=405 flag.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-04-24 13:32:47 -05:00
Stefan Roese 5020231bf7 [POWERPC] 4xx: Add NOR FLASH entries to Canyonlands and Glacier dts
This patch adds default NOR entries to the AMCC Canyonlands (460EX)
and Glacier (460GT) dts files.

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-04-24 13:32:46 -05:00
John Linn 2f0b45f846 [POWERPC] Xilinx: boot support for Xilinx uart 16550.
The Xilinx 16550 uart core is not a standard 16550 because it uses
word-based addressing rather than byte-based adressing. With
additional properties it is compatible with the open firmware
'ns16550' compatible binding.

This code updates the ns16550 driver to use the reg-offset property
so that the Xilinx UART 16550 can be used with it. The reg-shift
was already being handled.

Signed-off-by: John Linn <john.linn@xilinx.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-04-24 13:32:46 -05:00
Haiying Wang 8bdf573334 [POWERPC] 85xx: Fix the size of qe muram for MPC8568E
MPC8568E has 64K byte MURAM, so the size should be 0x10000, not 0xc000.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-04-17 09:52:18 -05:00
Paul Gortmaker 06f35b4ba6 [POWERPC] 86xx: mark functions static, other minor cleanups
Cleanups as suggested by Stephen Rothwell and Dale Farnsworth, which
incudes marking a bunch of functions static and add a vendor prefix to
the compat node check for uniqueness.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-04-17 09:51:29 -05:00
Kumar Gala 998c610363 [POWERPC] fsl: Convert dts to v1 syntax
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-04-17 09:40:48 -05:00
Kumar Gala 280bb34bc0 [POWERPC] 85xx: minor .dts cleanups
* remove #cpus from mpc8544ds.dts (not used anywhere else)
* remove memreserve from mpc8568mds.dts (not needed)

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-04-17 01:29:14 -05:00
Kumar Gala 32f960e943 [POWERPC] 85xx: Convert dts to v1 syntax
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-04-17 01:28:15 -05:00
Paul Gortmaker 81fad217b3 [POWERPC] 86xx: Add device tree source for Wind River SBC8641D
This adds in the device tree source for the SBC8641D, based
largely on the mpc8641_hpcn.dts.  The biggest differences are
the lack of a complex IRQ mapping (since no Uli/i8259 cascade)
and the different layout of devices on the localbus node.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-04-17 01:01:41 -05:00
Scott Wood 378458d865 [POWERPC] cuboot-pq2: PCI fixes
1. Detect (and bail out on) more conditions that violate the
assumptions of the setup code -- we assume in such cases that the device
tree is correct and reflects what the firmware did.

2. The inbound memory mask calculation was wrong.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-04-17 01:01:40 -05:00
Anton Vorontsov 56626f335b [POWERPC] QE: UCC nodes cleanup
- get rid of `model = "UCC"' in the ucc nodes
  It isn't used anywhere, so remove it. If we'll ever need something
  like this, we'll use compatible property instead.
- replace last occurrences of device-id with cell-index.
  Drivers are modified for backward compatibility's sake.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-04-17 01:01:38 -05:00
Laurent Pinchart 0585fa5fb7 [POWERPC] ep8248e: Reference SMC parameter RAM base in the device tree.
This patch modifies the Embedded Planet EP8248E device tree to reference the
SMC paramater RAM base register instead of the parameter RAM allocated by the
boot loader.

The cpm_uart driver will allocate parameter RAM itself, making the serial port
initialisation independent of the boot loader.

The patch adds the parameter RAM allocated by the boot loader in the CPM muram
node, making it available to the kernel.

Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-04-17 01:01:37 -05:00
Laurent Pinchart c2dd3529f3 [POWERPC] cpm-serial: Relocate CPM buffer descriptors and SMC parameter ram.
This patch relocates the buffer descriptors and the SMC parameter RAM at the
end of the first CPM muram chunk, as described in the device tree. This allows
device trees to stop excluding SMC parameter ram allocated by the boot loader
from the CPM muram node.

Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-04-17 01:01:37 -05:00
Laurent Pinchart da0a5f0c65 [POWERPC] Add bootwrapper function to get virtual reg from the device tree.
This patch adds a new generic device tree processing function that retrieves
virtual reg addresses from the device tree to the bootwrapper code. It also
updates the bootwrapper code to use the new function.

dt_get_virtual_reg() retrieves the virtual reg addresses from the
"virtual-reg" property. If the property can't be found, it uses the "reg"
property and walks the tree to translate it to absolute addresses.

Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-04-17 01:01:37 -05:00
Sebastian Siewior 1028d4f162 [POWERPC] 85xx: Enable DMA engine on the MPC8544 DS
Add the device tree node for the DMA engine on 8544, publish
the device and enable the driver in the defconfig.

Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-04-17 01:01:36 -05:00
Kumar Gala b18796d32a [POWERPC] bootwrapper: Use physical address in PHDR for uImage
Now that we properly set the physical address in the program header of the
vmlinux ELF we can extract it to properly set the load and entry point for
u-boot uImages.  Before we always hard coded the load & entry point to 0.
However there are situations that the kernel may be built with a non-zero
physical address.

We use objdump to extract the PHDR.  We assume that there is only one
PHDR in the vmlinux of type LOAD.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-04-17 07:46:14 +10:00
Dale Farnsworth a7e695f6bf [POWERPC] prpmc2800 needs a dtbImage
The prpmc2800 platform requires a zImage formatted file with an
embedded dtb file.  Rename the requested boot image file to
dtbImage.prpmc2800.

Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-04-15 21:21:25 +10:00
Dale Farnsworth a0916bd64a [POWERPC] mv643xx_eth: Prepare to support multiple silicon blocks
The mv643xx_eth driver is being modified to support multiple instances
of the ethernet silicon block on the same platform.  Each block contains
a single register bank containing the registers for up to three ports
interleaved within that bank.  This patch updates the PowerPC OF to
platform_device glue code to support multiple silicon blocks, each
with up to three ethernet ports.  The main difference is that we now
allow multiple mv64x60_shared platform_devices to be registered and
we provide each port platform_device with a pointer to its associated
shared platform_device.  The pointer will not be used until the
mv643xx_eth driver changes are committed.

Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-04-15 21:21:24 +10:00
Mark A. Greer 1791f91bc7 [POWERPC] prpmc2800: Clean up dts properties
Remove several unused (or software config only) properties.
Rename marvel node to "system-controller".  Also, rename the
"block-index" property to "cell-index" to conform to current
practice.

Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-04-15 21:21:24 +10:00
Dale Farnsworth a05ce88ab3 [POWERPC] mv64x60: Remove device tree absolute path references
Replace several device node absolute path lookups in the mv64x60
bootwrapper code with lookups by compatible or device_type
properties.

Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-04-15 21:21:24 +10:00
Mark A. Greer a1810b44c2 [POWERPC] mv64x60: Fix FDT compatible names: mv64x60 => mv64360
Compatible names should refer to a specific version of the hardware,
without wildcards.  Change each instance of mv64x60 to mv64360, which
is the oldest version we currently support.

Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-04-15 21:21:24 +10:00
Dale Farnsworth fb9d93de60 [POWERPC] prpmc2800: Fix frequencies in prpmc2800.dts
After the conversion to dts v1 format, seeing the frequencies
in decimal made it obvious that some of them had been
incorrectly truncated.  This fixes them.  Note that the PCI
frequency comes from a different source and is documented
as 66MHz, so it was left at 66000000.

Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-04-15 21:21:23 +10:00
Mark A. Greer d528be50c6 [POWERPC] prpmc2800: Convert DTS to v1 and add labels
Update the prpmc2800 DTS file to version 1 and add labels.
I verified that there was no change in the resulting dtb file.

Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-04-15 21:21:23 +10:00
Paul Mackerras ac7c5353b1 Merge branch 'linux-2.6' 2008-04-14 21:11:02 +10:00
Stefan Roese 9d7030be33 [POWERPC] 4xx: Change dts files to support jumbo frames
This patch changes the "max-frame-size" property to 9000 for all gbit
enabled 4xx boards. All those ports generally support jumbo frames, so
let's give the user a chance to enable it.

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-04-05 09:32:37 -05:00
Stefan Roese a6190a84ab [POWERPC] 4xx: Some EMAC related changes in Canyonlands & Glacier dts files
This patch fixes some problems in the Canyonlands 460EX and Glacier 460GT
dts files:

- Add "mdio-device = <&EMAC0>" to all all EMAC's except for EMAC0 itself
  (the 460EX/GT only can access the PHY via the EMAC0 instance)
- Add TAH support to Canyonlands dts

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-04-05 09:32:32 -05:00
René Bürgel 8d813941b1 [POWERPC] Fix MPC5200 (not B!) device tree so FEC ethernet works
This gets the FEC ethernet driver working again on the lite5200
platform.

The FEC driver is also compatible with the MPC5200, not only with the
MPC5200B, so this adds a suitable entry to the driver's match list.
Furthermore this adds the settings for the PHY in the dts file for the
Lite5200.  Note, that this is not exactly the same as in the
Lite5200B, because the PHY is located at f0003000:01 for the 5200, and
at :00 for the 5200B.  This was tested on a Lite5200 and a Lite5200B,
both booted a kernel via tftp and mounted the root via nfs
successfully.

Signed-off-by: René Bürgel <r.buergel@unicontrol.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-04-03 22:11:12 +11:00
Bartlomiej Sieka 115e1adca3 [POWERPC] mpc5200: Amalgamated DTS fixes and updates
DTS updates that fix booting problems on mpc5200-based boards:
- change to ethernet reg property
- addition of mdio and phy nodes
- removal of pci node (Motion-Pro board)

Other DTS updates:
- update i2c device tree nodes
- add lpb bus node and flash device (without partitions defined)
- add rtc i2c nodes

Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-04-03 22:11:12 +11:00
Grant Likely d2477b5cc8 [POWERPC] bootwrapper: Add a firmware-independent simpleboot target.
This target produces a flat binary rather than an ELF file,
fixes the entry point at the beginning of the image, and takes
a complete device tree with no fixups needed.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-04-02 20:36:11 -05:00
Grant Likely e04018e8e4 [POWERPC] add target for building .dtb files
Call dtc from the Makefile instead of the wrapper script so that the dt
blobs can be generated with a simple make invocation.

Using this patch allows board ports to trigger automatic building of .dtb
files by adding them to the image-y target list.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-04-02 20:29:11 -05:00
Harvey Harrison e48b1b452f [POWERPC] Replace remaining __FUNCTION__ occurrences
__FUNCTION__ is gcc-specific, use __func__

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-04-01 20:43:09 +11:00
Geoff Levand 5761eaa3a5 [POWERPC] PS3: Bootwrapper improvements
Improve the debugging support of the PS3 bootwraper code:

 o Increase the size of the PS3 bootwrapper overlay from 256 to 512 bytes to
   allow for more debugging code in the overlay.
 o Use the dot symbol to set the size of __system_reset_overlay.  The
   assembler will then emit an error if the overlay code is too big.
 o Remove some unused instructions.
 o Update the text describing the PS3 bootwrapper overlay.
 o Add a check for null pointer writes.
 o Change hcall return value from s64.

Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-04-01 20:43:07 +11:00
Paul Mackerras e6b18912d3 Merge branch 'powerpc-next' of master.kernel.org:/pub/scm/linux/kernel/git/galak/powerpc 2008-04-01 20:34:26 +11:00
Kim Phillips 96ce1b6dc5 [POWERPC] sata_fsl: reduce compatibility to fsl,pq-sata
as prescribed in Documentation/powerpc/booting-without-of.txt.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-03-31 10:27:35 -05:00
Anton Vorontsov 8e8ff3a309 [POWERPC] 83xx: Fix wrong USB phy type in mpc837xrdb dts
Due to chip constraint MPC837x USB DR module can only use
ULPI and serial PHY interfaces.  The patch fixes the wrong
type in dts.

This patch fixes USB malfunctioning on the MPC837xE-RDB boards.

Similar patch has been already applied for the MDS boards:

  commit 28b9588592
  Author: Li Yang <leoli@freescale.com>
  Date:   Thu Mar 6 18:42:26 2008 +0800

      [POWERPC] 83xx: Fix wrong USB phy type in mpc837xmds dts

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-03-31 10:23:48 -05:00
Alexandr Smirnov ee0a3f564e [POWERPC] 85xx: Emerson KSI8560 device tree
Add device tree file for Emerson KSI8560 board.

Signed-off-by: Alexandr Smirnov <asmirnov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-03-26 11:30:46 -05:00
Alexandr Smirnov ff880112af [POWERPC] 85xx: Emerson KSI8560 bootwrapper
Add boot wrapper for Emerson KSI8560 board.

Signed-off-by: Alexandr Smirnov <asmirnov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-03-26 11:30:45 -05:00
Stefan Roese 99d8be052e [POWERPC] 4xx: Add L2 cache node to AMCC Taishan dts file
This patch adds the L2 cache node to the Taishan 440GX dts file.

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-03-26 07:28:01 -05:00
Stefan Roese 145692a734 [POWERPC] 4xx: Add "amcc, haleakala" to the toplevel compatible property
Currently Haleakala uses the Kilauea platform code. This patch adds
"haleakala" to the compatible property, in case later kernel versions
will introduce a Haleakala platform code.

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-03-26 07:27:45 -05:00
Stefan Roese c06cf7dad6 [POWERPC] 4xx: Add AMCC Glacier 460GT eval board dts
The patch adds the Glacier dts. The Glacier is nearly identical to the
Canyonlands (460EX). Here the differences:

- 4 ethernet ports instead of 2
- no SATA port
- no USB port

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-03-26 07:27:38 -05:00
Stefan Roese 7831426351 [POWERPC] 4xx: Add TAH support to taishan dts
This patch adds TAH (TCP/IP Acceleration Hardware) support to the
taishan 440GX dts. It depends on the NEWEMAC/tah patch that adds the
compatible "ibm,tah" property to the matching table.

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-03-26 07:26:55 -05:00
Josh Boyer d0a48c9f4c [POWERPC] 4xx: Add bootwrapper for AMCC Yosemite board
Add the cuboot wrapper for the AMCC 440EP Yosemite board

Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-03-26 07:19:17 -05:00
Josh Boyer fd0ed740a1 [POWERPC] 4xx: Add AMCC 440EP Yosemite DTS
This adds a DTS file for the AMCC 440EP Yosemite board.

Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-03-26 07:19:17 -05:00
Stefan Roese 8bc4a51d28 [POWERPC] 4xx: Add Canyonlands DTS
This dts source file for the AMCC 460EX Canyonlands evalutaion board

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-03-26 07:19:16 -05:00
David Gibson ecc6cd73b7 [POWERPC] Start removing linux,network-index in favour of aliases
This patch alters the bootwrapper for a number of machines (roubhly
all 4xx based cuboot or treeboot platforms) to use aliases instead of
the linux,network-index hack to work out which MAC address to attach
to which ethernet device node.

The now obsolete linux,network-index properties are removed from the
corresponding device trees.  This won't break backwards compatiblity,
because in cases where this fixup code is relevant, the device tree is
part of the kernel image.

The references to linux,network-index are removed from
booting-without-of.txt.  Not only is it now deprecated, but as a hack
applicable only when the device tree blob and fixup code were in the
same image, this property never belonged in booting-without-of.txt
which describes the interface between the kernel and firmware or
bootloaders which produce a device tree.  By the time the device tree
reaches the kernel, all the MAC addresses must be fully filled in.

Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-03-26 07:19:16 -05:00
Grant Likely 5492a7e4cb [POWERPC] mpc5200: Fix incorrect compatible string for the mdio node
The MDIO node in the lite5200b.dts file needs to also claim compatibility
with the older mpc5200 chip.  Otherwise the driver won't find the device.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-03-25 13:18:39 +11:00