1658 lines
51 KiB
C
1658 lines
51 KiB
C
/*
|
|
w83792d.c - Part of lm_sensors, Linux kernel modules for hardware
|
|
monitoring
|
|
Copyright (C) 2004, 2005 Winbond Electronics Corp.
|
|
Chunhao Huang <DZShen@Winbond.com.tw>,
|
|
Rudolf Marek <r.marek@sh.cvut.cz>
|
|
|
|
This program is free software; you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation; either version 2 of the License, or
|
|
(at your option) any later version.
|
|
|
|
This program is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with this program; if not, write to the Free Software
|
|
Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
|
|
|
|
Note:
|
|
1. This driver is only for 2.6 kernel, 2.4 kernel need a different driver.
|
|
2. This driver is only for Winbond W83792D C version device, there
|
|
are also some motherboards with B version W83792D device. The
|
|
calculation method to in6-in7(measured value, limits) is a little
|
|
different between C and B version. C or B version can be identified
|
|
by CR[0x49h].
|
|
*/
|
|
|
|
/*
|
|
Supports following chips:
|
|
|
|
Chip #vin #fanin #pwm #temp wchipid vendid i2c ISA
|
|
w83792d 9 7 7 3 0x7a 0x5ca3 yes no
|
|
*/
|
|
|
|
#include <linux/config.h>
|
|
#include <linux/module.h>
|
|
#include <linux/init.h>
|
|
#include <linux/slab.h>
|
|
#include <linux/i2c.h>
|
|
#include <linux/hwmon.h>
|
|
#include <linux/hwmon-sysfs.h>
|
|
#include <linux/err.h>
|
|
|
|
/* Addresses to scan */
|
|
static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, 0x2f, I2C_CLIENT_END };
|
|
|
|
/* Insmod parameters */
|
|
I2C_CLIENT_INSMOD_1(w83792d);
|
|
I2C_CLIENT_MODULE_PARM(force_subclients, "List of subclient addresses: "
|
|
"{bus, clientaddr, subclientaddr1, subclientaddr2}");
|
|
|
|
static int init;
|
|
module_param(init, bool, 0);
|
|
MODULE_PARM_DESC(init, "Set to one to force chip initialization");
|
|
|
|
/* The W83792D registers */
|
|
static const u8 W83792D_REG_IN[9] = {
|
|
0x20, /* Vcore A in DataSheet */
|
|
0x21, /* Vcore B in DataSheet */
|
|
0x22, /* VIN0 in DataSheet */
|
|
0x23, /* VIN1 in DataSheet */
|
|
0x24, /* VIN2 in DataSheet */
|
|
0x25, /* VIN3 in DataSheet */
|
|
0x26, /* 5VCC in DataSheet */
|
|
0xB0, /* 5VSB in DataSheet */
|
|
0xB1 /* VBAT in DataSheet */
|
|
};
|
|
#define W83792D_REG_LOW_BITS1 0x3E /* Low Bits I in DataSheet */
|
|
#define W83792D_REG_LOW_BITS2 0x3F /* Low Bits II in DataSheet */
|
|
static const u8 W83792D_REG_IN_MAX[9] = {
|
|
0x2B, /* Vcore A High Limit in DataSheet */
|
|
0x2D, /* Vcore B High Limit in DataSheet */
|
|
0x2F, /* VIN0 High Limit in DataSheet */
|
|
0x31, /* VIN1 High Limit in DataSheet */
|
|
0x33, /* VIN2 High Limit in DataSheet */
|
|
0x35, /* VIN3 High Limit in DataSheet */
|
|
0x37, /* 5VCC High Limit in DataSheet */
|
|
0xB4, /* 5VSB High Limit in DataSheet */
|
|
0xB6 /* VBAT High Limit in DataSheet */
|
|
};
|
|
static const u8 W83792D_REG_IN_MIN[9] = {
|
|
0x2C, /* Vcore A Low Limit in DataSheet */
|
|
0x2E, /* Vcore B Low Limit in DataSheet */
|
|
0x30, /* VIN0 Low Limit in DataSheet */
|
|
0x32, /* VIN1 Low Limit in DataSheet */
|
|
0x34, /* VIN2 Low Limit in DataSheet */
|
|
0x36, /* VIN3 Low Limit in DataSheet */
|
|
0x38, /* 5VCC Low Limit in DataSheet */
|
|
0xB5, /* 5VSB Low Limit in DataSheet */
|
|
0xB7 /* VBAT Low Limit in DataSheet */
|
|
};
|
|
static const u8 W83792D_REG_FAN[7] = {
|
|
0x28, /* FAN 1 Count in DataSheet */
|
|
0x29, /* FAN 2 Count in DataSheet */
|
|
0x2A, /* FAN 3 Count in DataSheet */
|
|
0xB8, /* FAN 4 Count in DataSheet */
|
|
0xB9, /* FAN 5 Count in DataSheet */
|
|
0xBA, /* FAN 6 Count in DataSheet */
|
|
0xBE /* FAN 7 Count in DataSheet */
|
|
};
|
|
static const u8 W83792D_REG_FAN_MIN[7] = {
|
|
0x3B, /* FAN 1 Count Low Limit in DataSheet */
|
|
0x3C, /* FAN 2 Count Low Limit in DataSheet */
|
|
0x3D, /* FAN 3 Count Low Limit in DataSheet */
|
|
0xBB, /* FAN 4 Count Low Limit in DataSheet */
|
|
0xBC, /* FAN 5 Count Low Limit in DataSheet */
|
|
0xBD, /* FAN 6 Count Low Limit in DataSheet */
|
|
0xBF /* FAN 7 Count Low Limit in DataSheet */
|
|
};
|
|
#define W83792D_REG_FAN_CFG 0x84 /* FAN Configuration in DataSheet */
|
|
static const u8 W83792D_REG_FAN_DIV[4] = {
|
|
0x47, /* contains FAN2 and FAN1 Divisor */
|
|
0x5B, /* contains FAN4 and FAN3 Divisor */
|
|
0x5C, /* contains FAN6 and FAN5 Divisor */
|
|
0x9E /* contains FAN7 Divisor. */
|
|
};
|
|
static const u8 W83792D_REG_PWM[7] = {
|
|
0x81, /* FAN 1 Duty Cycle, be used to control */
|
|
0x83, /* FAN 2 Duty Cycle, be used to control */
|
|
0x94, /* FAN 3 Duty Cycle, be used to control */
|
|
0xA3, /* FAN 4 Duty Cycle, be used to control */
|
|
0xA4, /* FAN 5 Duty Cycle, be used to control */
|
|
0xA5, /* FAN 6 Duty Cycle, be used to control */
|
|
0xA6 /* FAN 7 Duty Cycle, be used to control */
|
|
};
|
|
#define W83792D_REG_BANK 0x4E
|
|
#define W83792D_REG_TEMP2_CONFIG 0xC2
|
|
#define W83792D_REG_TEMP3_CONFIG 0xCA
|
|
|
|
static const u8 W83792D_REG_TEMP1[3] = {
|
|
0x27, /* TEMP 1 in DataSheet */
|
|
0x39, /* TEMP 1 Over in DataSheet */
|
|
0x3A, /* TEMP 1 Hyst in DataSheet */
|
|
};
|
|
|
|
static const u8 W83792D_REG_TEMP_ADD[2][6] = {
|
|
{ 0xC0, /* TEMP 2 in DataSheet */
|
|
0xC1, /* TEMP 2(0.5 deg) in DataSheet */
|
|
0xC5, /* TEMP 2 Over High part in DataSheet */
|
|
0xC6, /* TEMP 2 Over Low part in DataSheet */
|
|
0xC3, /* TEMP 2 Thyst High part in DataSheet */
|
|
0xC4 }, /* TEMP 2 Thyst Low part in DataSheet */
|
|
{ 0xC8, /* TEMP 3 in DataSheet */
|
|
0xC9, /* TEMP 3(0.5 deg) in DataSheet */
|
|
0xCD, /* TEMP 3 Over High part in DataSheet */
|
|
0xCE, /* TEMP 3 Over Low part in DataSheet */
|
|
0xCB, /* TEMP 3 Thyst High part in DataSheet */
|
|
0xCC } /* TEMP 3 Thyst Low part in DataSheet */
|
|
};
|
|
|
|
static const u8 W83792D_REG_THERMAL[3] = {
|
|
0x85, /* SmartFanI: Fan1 target value */
|
|
0x86, /* SmartFanI: Fan2 target value */
|
|
0x96 /* SmartFanI: Fan3 target value */
|
|
};
|
|
|
|
static const u8 W83792D_REG_TOLERANCE[3] = {
|
|
0x87, /* (bit3-0)SmartFan Fan1 tolerance */
|
|
0x87, /* (bit7-4)SmartFan Fan2 tolerance */
|
|
0x97 /* (bit3-0)SmartFan Fan3 tolerance */
|
|
};
|
|
|
|
static const u8 W83792D_REG_POINTS[3][4] = {
|
|
{ 0x85, /* SmartFanII: Fan1 temp point 1 */
|
|
0xE3, /* SmartFanII: Fan1 temp point 2 */
|
|
0xE4, /* SmartFanII: Fan1 temp point 3 */
|
|
0xE5 }, /* SmartFanII: Fan1 temp point 4 */
|
|
{ 0x86, /* SmartFanII: Fan2 temp point 1 */
|
|
0xE6, /* SmartFanII: Fan2 temp point 2 */
|
|
0xE7, /* SmartFanII: Fan2 temp point 3 */
|
|
0xE8 }, /* SmartFanII: Fan2 temp point 4 */
|
|
{ 0x96, /* SmartFanII: Fan3 temp point 1 */
|
|
0xE9, /* SmartFanII: Fan3 temp point 2 */
|
|
0xEA, /* SmartFanII: Fan3 temp point 3 */
|
|
0xEB } /* SmartFanII: Fan3 temp point 4 */
|
|
};
|
|
|
|
static const u8 W83792D_REG_LEVELS[3][4] = {
|
|
{ 0x88, /* (bit3-0) SmartFanII: Fan1 Non-Stop */
|
|
0x88, /* (bit7-4) SmartFanII: Fan1 Level 1 */
|
|
0xE0, /* (bit7-4) SmartFanII: Fan1 Level 2 */
|
|
0xE0 }, /* (bit3-0) SmartFanII: Fan1 Level 3 */
|
|
{ 0x89, /* (bit3-0) SmartFanII: Fan2 Non-Stop */
|
|
0x89, /* (bit7-4) SmartFanII: Fan2 Level 1 */
|
|
0xE1, /* (bit7-4) SmartFanII: Fan2 Level 2 */
|
|
0xE1 }, /* (bit3-0) SmartFanII: Fan2 Level 3 */
|
|
{ 0x98, /* (bit3-0) SmartFanII: Fan3 Non-Stop */
|
|
0x98, /* (bit7-4) SmartFanII: Fan3 Level 1 */
|
|
0xE2, /* (bit7-4) SmartFanII: Fan3 Level 2 */
|
|
0xE2 } /* (bit3-0) SmartFanII: Fan3 Level 3 */
|
|
};
|
|
|
|
#define W83792D_REG_GPIO_EN 0x1A
|
|
#define W83792D_REG_CONFIG 0x40
|
|
#define W83792D_REG_VID_FANDIV 0x47
|
|
#define W83792D_REG_CHIPID 0x49
|
|
#define W83792D_REG_WCHIPID 0x58
|
|
#define W83792D_REG_CHIPMAN 0x4F
|
|
#define W83792D_REG_PIN 0x4B
|
|
#define W83792D_REG_I2C_SUBADDR 0x4A
|
|
|
|
#define W83792D_REG_ALARM1 0xA9 /* realtime status register1 */
|
|
#define W83792D_REG_ALARM2 0xAA /* realtime status register2 */
|
|
#define W83792D_REG_ALARM3 0xAB /* realtime status register3 */
|
|
#define W83792D_REG_CHASSIS 0x42 /* Bit 5: Case Open status bit */
|
|
#define W83792D_REG_CHASSIS_CLR 0x44 /* Bit 7: Case Open CLR_CHS/Reset bit */
|
|
|
|
/* control in0/in1 's limit modifiability */
|
|
#define W83792D_REG_VID_IN_B 0x17
|
|
|
|
#define W83792D_REG_VBAT 0x5D
|
|
#define W83792D_REG_I2C_ADDR 0x48
|
|
|
|
/* Conversions. Rounding and limit checking is only done on the TO_REG
|
|
variants. Note that you should be a bit careful with which arguments
|
|
these macros are called: arguments may be evaluated more than once.
|
|
Fixing this is just not worth it. */
|
|
#define IN_FROM_REG(nr,val) (((nr)<=1)?(val*2): \
|
|
((((nr)==6)||((nr)==7))?(val*6):(val*4)))
|
|
#define IN_TO_REG(nr,val) (((nr)<=1)?(val/2): \
|
|
((((nr)==6)||((nr)==7))?(val/6):(val/4)))
|
|
|
|
static inline u8
|
|
FAN_TO_REG(long rpm, int div)
|
|
{
|
|
if (rpm == 0)
|
|
return 255;
|
|
rpm = SENSORS_LIMIT(rpm, 1, 1000000);
|
|
return SENSORS_LIMIT((1350000 + rpm * div / 2) / (rpm * div), 1, 254);
|
|
}
|
|
|
|
#define FAN_FROM_REG(val,div) ((val) == 0 ? -1 : \
|
|
((val) == 255 ? 0 : \
|
|
1350000 / ((val) * (div))))
|
|
|
|
/* for temp1 */
|
|
#define TEMP1_TO_REG(val) (SENSORS_LIMIT(((val) < 0 ? (val)+0x100*1000 \
|
|
: (val)) / 1000, 0, 0xff))
|
|
#define TEMP1_FROM_REG(val) (((val) & 0x80 ? (val)-0x100 : (val)) * 1000)
|
|
/* for temp2 and temp3, because they need addtional resolution */
|
|
#define TEMP_ADD_FROM_REG(val1, val2) \
|
|
((((val1) & 0x80 ? (val1)-0x100 \
|
|
: (val1)) * 1000) + ((val2 & 0x80) ? 500 : 0))
|
|
#define TEMP_ADD_TO_REG_HIGH(val) \
|
|
(SENSORS_LIMIT(((val) < 0 ? (val)+0x100*1000 \
|
|
: (val)) / 1000, 0, 0xff))
|
|
#define TEMP_ADD_TO_REG_LOW(val) ((val%1000) ? 0x80 : 0x00)
|
|
|
|
#define PWM_FROM_REG(val) (val)
|
|
#define PWM_TO_REG(val) (SENSORS_LIMIT((val),0,255))
|
|
#define DIV_FROM_REG(val) (1 << (val))
|
|
|
|
static inline u8
|
|
DIV_TO_REG(long val)
|
|
{
|
|
int i;
|
|
val = SENSORS_LIMIT(val, 1, 128) >> 1;
|
|
for (i = 0; i < 7; i++) {
|
|
if (val == 0)
|
|
break;
|
|
val >>= 1;
|
|
}
|
|
return ((u8) i);
|
|
}
|
|
|
|
struct w83792d_data {
|
|
struct i2c_client client;
|
|
struct class_device *class_dev;
|
|
struct semaphore lock;
|
|
enum chips type;
|
|
|
|
struct semaphore update_lock;
|
|
char valid; /* !=0 if following fields are valid */
|
|
unsigned long last_updated; /* In jiffies */
|
|
|
|
/* array of 2 pointers to subclients */
|
|
struct i2c_client *lm75[2];
|
|
|
|
u8 in[9]; /* Register value */
|
|
u8 in_max[9]; /* Register value */
|
|
u8 in_min[9]; /* Register value */
|
|
u8 low_bits[2]; /* Additional resolution to voltage in0-6 */
|
|
u8 fan[7]; /* Register value */
|
|
u8 fan_min[7]; /* Register value */
|
|
u8 temp1[3]; /* current, over, thyst */
|
|
u8 temp_add[2][6]; /* Register value */
|
|
u8 fan_div[7]; /* Register encoding, shifted right */
|
|
u8 pwm[7]; /* We only consider the first 3 set of pwm,
|
|
although 792 chip has 7 set of pwm. */
|
|
u8 pwmenable[3];
|
|
u8 pwm_mode[7]; /* indicates PWM or DC mode: 1->PWM; 0->DC */
|
|
u32 alarms; /* realtime status register encoding,combined */
|
|
u8 chassis; /* Chassis status */
|
|
u8 chassis_clear; /* CLR_CHS, clear chassis intrusion detection */
|
|
u8 thermal_cruise[3]; /* Smart FanI: Fan1,2,3 target value */
|
|
u8 tolerance[3]; /* Fan1,2,3 tolerance(Smart Fan I/II) */
|
|
u8 sf2_points[3][4]; /* Smart FanII: Fan1,2,3 temperature points */
|
|
u8 sf2_levels[3][4]; /* Smart FanII: Fan1,2,3 duty cycle levels */
|
|
};
|
|
|
|
static int w83792d_attach_adapter(struct i2c_adapter *adapter);
|
|
static int w83792d_detect(struct i2c_adapter *adapter, int address, int kind);
|
|
static int w83792d_detach_client(struct i2c_client *client);
|
|
|
|
static int w83792d_read_value(struct i2c_client *client, u8 register);
|
|
static int w83792d_write_value(struct i2c_client *client, u8 register,
|
|
u8 value);
|
|
static struct w83792d_data *w83792d_update_device(struct device *dev);
|
|
|
|
#ifdef DEBUG
|
|
static void w83792d_print_debug(struct w83792d_data *data, struct device *dev);
|
|
#endif
|
|
|
|
static void w83792d_init_client(struct i2c_client *client);
|
|
|
|
static struct i2c_driver w83792d_driver = {
|
|
.owner = THIS_MODULE,
|
|
.name = "w83792d",
|
|
.flags = I2C_DF_NOTIFY,
|
|
.attach_adapter = w83792d_attach_adapter,
|
|
.detach_client = w83792d_detach_client,
|
|
};
|
|
|
|
static long in_count_from_reg(int nr, struct w83792d_data *data)
|
|
{
|
|
u16 vol_count = data->in[nr];
|
|
u16 low_bits = 0;
|
|
vol_count = (vol_count << 2);
|
|
switch (nr)
|
|
{
|
|
case 0: /* vin0 */
|
|
low_bits = (data->low_bits[0]) & 0x03;
|
|
break;
|
|
case 1: /* vin1 */
|
|
low_bits = ((data->low_bits[0]) & 0x0c) >> 2;
|
|
break;
|
|
case 2: /* vin2 */
|
|
low_bits = ((data->low_bits[0]) & 0x30) >> 4;
|
|
break;
|
|
case 3: /* vin3 */
|
|
low_bits = ((data->low_bits[0]) & 0xc0) >> 6;
|
|
break;
|
|
case 4: /* vin4 */
|
|
low_bits = (data->low_bits[1]) & 0x03;
|
|
break;
|
|
case 5: /* vin5 */
|
|
low_bits = ((data->low_bits[1]) & 0x0c) >> 2;
|
|
break;
|
|
case 6: /* vin6 */
|
|
low_bits = ((data->low_bits[1]) & 0x30) >> 4;
|
|
default:
|
|
break;
|
|
}
|
|
vol_count = vol_count | low_bits;
|
|
return vol_count;
|
|
}
|
|
|
|
/* following are the sysfs callback functions */
|
|
static ssize_t show_in(struct device *dev, struct device_attribute *attr,
|
|
char *buf)
|
|
{
|
|
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
|
|
int nr = sensor_attr->index;
|
|
struct w83792d_data *data = w83792d_update_device(dev);
|
|
return sprintf(buf,"%ld\n", IN_FROM_REG(nr,(in_count_from_reg(nr, data))));
|
|
}
|
|
|
|
#define show_in_reg(reg) \
|
|
static ssize_t show_##reg(struct device *dev, struct device_attribute *attr, \
|
|
char *buf) \
|
|
{ \
|
|
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); \
|
|
int nr = sensor_attr->index; \
|
|
struct w83792d_data *data = w83792d_update_device(dev); \
|
|
return sprintf(buf,"%ld\n", (long)(IN_FROM_REG(nr, (data->reg[nr])*4))); \
|
|
}
|
|
|
|
show_in_reg(in_min);
|
|
show_in_reg(in_max);
|
|
|
|
#define store_in_reg(REG, reg) \
|
|
static ssize_t store_in_##reg (struct device *dev, \
|
|
struct device_attribute *attr, \
|
|
const char *buf, size_t count) \
|
|
{ \
|
|
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); \
|
|
int nr = sensor_attr->index; \
|
|
struct i2c_client *client = to_i2c_client(dev); \
|
|
struct w83792d_data *data = i2c_get_clientdata(client); \
|
|
u32 val; \
|
|
\
|
|
val = simple_strtoul(buf, NULL, 10); \
|
|
data->in_##reg[nr] = SENSORS_LIMIT(IN_TO_REG(nr, val)/4, 0, 255); \
|
|
w83792d_write_value(client, W83792D_REG_IN_##REG[nr], data->in_##reg[nr]); \
|
|
\
|
|
return count; \
|
|
}
|
|
store_in_reg(MIN, min);
|
|
store_in_reg(MAX, max);
|
|
|
|
#define sysfs_in_reg(offset) \
|
|
static SENSOR_DEVICE_ATTR(in##offset##_input, S_IRUGO, show_in, \
|
|
NULL, offset); \
|
|
static SENSOR_DEVICE_ATTR(in##offset##_min, S_IRUGO | S_IWUSR, \
|
|
show_in_min, store_in_min, offset); \
|
|
static SENSOR_DEVICE_ATTR(in##offset##_max, S_IRUGO | S_IWUSR, \
|
|
show_in_max, store_in_max, offset);
|
|
|
|
sysfs_in_reg(0);
|
|
sysfs_in_reg(1);
|
|
sysfs_in_reg(2);
|
|
sysfs_in_reg(3);
|
|
sysfs_in_reg(4);
|
|
sysfs_in_reg(5);
|
|
sysfs_in_reg(6);
|
|
sysfs_in_reg(7);
|
|
sysfs_in_reg(8);
|
|
|
|
#define device_create_file_in(client, offset) \
|
|
do { \
|
|
device_create_file(&client->dev, &sensor_dev_attr_in##offset##_input.dev_attr); \
|
|
device_create_file(&client->dev, &sensor_dev_attr_in##offset##_max.dev_attr); \
|
|
device_create_file(&client->dev, &sensor_dev_attr_in##offset##_min.dev_attr); \
|
|
} while (0)
|
|
|
|
#define show_fan_reg(reg) \
|
|
static ssize_t show_##reg (struct device *dev, struct device_attribute *attr, \
|
|
char *buf) \
|
|
{ \
|
|
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); \
|
|
int nr = sensor_attr->index - 1; \
|
|
struct w83792d_data *data = w83792d_update_device(dev); \
|
|
return sprintf(buf,"%d\n", \
|
|
FAN_FROM_REG(data->reg[nr], DIV_FROM_REG(data->fan_div[nr]))); \
|
|
}
|
|
|
|
show_fan_reg(fan);
|
|
show_fan_reg(fan_min);
|
|
|
|
static ssize_t
|
|
store_fan_min(struct device *dev, struct device_attribute *attr,
|
|
const char *buf, size_t count)
|
|
{
|
|
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
|
|
int nr = sensor_attr->index - 1;
|
|
struct i2c_client *client = to_i2c_client(dev);
|
|
struct w83792d_data *data = i2c_get_clientdata(client);
|
|
u32 val;
|
|
|
|
val = simple_strtoul(buf, NULL, 10);
|
|
data->fan_min[nr] = FAN_TO_REG(val, DIV_FROM_REG(data->fan_div[nr]));
|
|
w83792d_write_value(client, W83792D_REG_FAN_MIN[nr],
|
|
data->fan_min[nr]);
|
|
|
|
return count;
|
|
}
|
|
|
|
static ssize_t
|
|
show_fan_div(struct device *dev, struct device_attribute *attr,
|
|
char *buf)
|
|
{
|
|
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
|
|
int nr = sensor_attr->index;
|
|
struct w83792d_data *data = w83792d_update_device(dev);
|
|
return sprintf(buf, "%u\n", DIV_FROM_REG(data->fan_div[nr - 1]));
|
|
}
|
|
|
|
/* Note: we save and restore the fan minimum here, because its value is
|
|
determined in part by the fan divisor. This follows the principle of
|
|
least suprise; the user doesn't expect the fan minimum to change just
|
|
because the divisor changed. */
|
|
static ssize_t
|
|
store_fan_div(struct device *dev, struct device_attribute *attr,
|
|
const char *buf, size_t count)
|
|
{
|
|
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
|
|
int nr = sensor_attr->index - 1;
|
|
struct i2c_client *client = to_i2c_client(dev);
|
|
struct w83792d_data *data = i2c_get_clientdata(client);
|
|
unsigned long min;
|
|
/*u8 reg;*/
|
|
u8 fan_div_reg = 0;
|
|
u8 tmp_fan_div;
|
|
|
|
/* Save fan_min */
|
|
min = FAN_FROM_REG(data->fan_min[nr],
|
|
DIV_FROM_REG(data->fan_div[nr]));
|
|
|
|
data->fan_div[nr] = DIV_TO_REG(simple_strtoul(buf, NULL, 10));
|
|
|
|
fan_div_reg = w83792d_read_value(client, W83792D_REG_FAN_DIV[nr >> 1]);
|
|
fan_div_reg &= (nr & 0x01) ? 0x8f : 0xf8;
|
|
tmp_fan_div = (nr & 0x01) ? (((data->fan_div[nr]) << 4) & 0x70)
|
|
: ((data->fan_div[nr]) & 0x07);
|
|
w83792d_write_value(client, W83792D_REG_FAN_DIV[nr >> 1],
|
|
fan_div_reg | tmp_fan_div);
|
|
|
|
/* Restore fan_min */
|
|
data->fan_min[nr] = FAN_TO_REG(min, DIV_FROM_REG(data->fan_div[nr]));
|
|
w83792d_write_value(client, W83792D_REG_FAN_MIN[nr], data->fan_min[nr]);
|
|
|
|
return count;
|
|
}
|
|
|
|
#define sysfs_fan(offset) \
|
|
static SENSOR_DEVICE_ATTR(fan##offset##_input, S_IRUGO, show_fan, NULL, \
|
|
offset); \
|
|
static SENSOR_DEVICE_ATTR(fan##offset##_div, S_IRUGO | S_IWUSR, \
|
|
show_fan_div, store_fan_div, offset); \
|
|
static SENSOR_DEVICE_ATTR(fan##offset##_min, S_IRUGO | S_IWUSR, \
|
|
show_fan_min, store_fan_min, offset);
|
|
|
|
sysfs_fan(1);
|
|
sysfs_fan(2);
|
|
sysfs_fan(3);
|
|
sysfs_fan(4);
|
|
sysfs_fan(5);
|
|
sysfs_fan(6);
|
|
sysfs_fan(7);
|
|
|
|
#define device_create_file_fan(client, offset) \
|
|
do { \
|
|
device_create_file(&client->dev, &sensor_dev_attr_fan##offset##_input.dev_attr); \
|
|
device_create_file(&client->dev, &sensor_dev_attr_fan##offset##_div.dev_attr); \
|
|
device_create_file(&client->dev, &sensor_dev_attr_fan##offset##_min.dev_attr); \
|
|
} while (0)
|
|
|
|
|
|
/* read/write the temperature1, includes measured value and limits */
|
|
|
|
static ssize_t show_temp1(struct device *dev, struct device_attribute *attr,
|
|
char *buf)
|
|
{
|
|
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
|
|
int nr = sensor_attr->index;
|
|
struct w83792d_data *data = w83792d_update_device(dev);
|
|
return sprintf(buf, "%d\n", TEMP1_FROM_REG(data->temp1[nr]));
|
|
}
|
|
|
|
static ssize_t store_temp1(struct device *dev, struct device_attribute *attr,
|
|
const char *buf, size_t count)
|
|
{
|
|
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
|
|
int nr = sensor_attr->index;
|
|
struct i2c_client *client = to_i2c_client(dev);
|
|
struct w83792d_data *data = i2c_get_clientdata(client);
|
|
s32 val;
|
|
|
|
val = simple_strtol(buf, NULL, 10);
|
|
|
|
data->temp1[nr] = TEMP1_TO_REG(val);
|
|
w83792d_write_value(client, W83792D_REG_TEMP1[nr],
|
|
data->temp1[nr]);
|
|
|
|
return count;
|
|
}
|
|
|
|
|
|
static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, show_temp1, NULL, 0);
|
|
static SENSOR_DEVICE_ATTR(temp1_max, S_IRUGO | S_IWUSR, show_temp1,
|
|
store_temp1, 1);
|
|
static SENSOR_DEVICE_ATTR(temp1_max_hyst, S_IRUGO | S_IWUSR, show_temp1,
|
|
store_temp1, 2);
|
|
|
|
#define device_create_file_temp1(client) \
|
|
do { \
|
|
device_create_file(&client->dev, &sensor_dev_attr_temp1_input.dev_attr); \
|
|
device_create_file(&client->dev, &sensor_dev_attr_temp1_max.dev_attr); \
|
|
device_create_file(&client->dev, &sensor_dev_attr_temp1_max_hyst.dev_attr); \
|
|
} while (0)
|
|
|
|
|
|
/* read/write the temperature2-3, includes measured value and limits */
|
|
|
|
static ssize_t show_temp23(struct device *dev, struct device_attribute *attr,
|
|
char *buf)
|
|
{
|
|
struct sensor_device_attribute_2 *sensor_attr = to_sensor_dev_attr_2(attr);
|
|
int nr = sensor_attr->nr;
|
|
int index = sensor_attr->index;
|
|
struct w83792d_data *data = w83792d_update_device(dev);
|
|
return sprintf(buf,"%ld\n",
|
|
(long)TEMP_ADD_FROM_REG(data->temp_add[nr][index],
|
|
data->temp_add[nr][index+1]));
|
|
}
|
|
|
|
static ssize_t store_temp23(struct device *dev, struct device_attribute *attr,
|
|
const char *buf, size_t count)
|
|
{
|
|
struct sensor_device_attribute_2 *sensor_attr = to_sensor_dev_attr_2(attr);
|
|
int nr = sensor_attr->nr;
|
|
int index = sensor_attr->index;
|
|
struct i2c_client *client = to_i2c_client(dev);
|
|
struct w83792d_data *data = i2c_get_clientdata(client);
|
|
s32 val;
|
|
|
|
val = simple_strtol(buf, NULL, 10);
|
|
|
|
data->temp_add[nr][index] = TEMP_ADD_TO_REG_HIGH(val);
|
|
data->temp_add[nr][index+1] = TEMP_ADD_TO_REG_LOW(val);
|
|
w83792d_write_value(client, W83792D_REG_TEMP_ADD[nr][index],
|
|
data->temp_add[nr][index]);
|
|
w83792d_write_value(client, W83792D_REG_TEMP_ADD[nr][index+1],
|
|
data->temp_add[nr][index+1]);
|
|
|
|
return count;
|
|
}
|
|
|
|
#define sysfs_temp23(name,idx) \
|
|
static SENSOR_DEVICE_ATTR_2(name##_input, S_IRUGO, show_temp23, NULL, \
|
|
idx, 0); \
|
|
static SENSOR_DEVICE_ATTR_2(name##_max, S_IRUGO | S_IWUSR, \
|
|
show_temp23, store_temp23, idx, 2); \
|
|
static SENSOR_DEVICE_ATTR_2(name##_max_hyst, S_IRUGO | S_IWUSR, \
|
|
show_temp23, store_temp23, idx, 4);
|
|
|
|
sysfs_temp23(temp2,0)
|
|
sysfs_temp23(temp3,1)
|
|
|
|
#define device_create_file_temp_add(client, offset) \
|
|
do { \
|
|
device_create_file(&client->dev, &sensor_dev_attr_temp##offset##_input.dev_attr); \
|
|
device_create_file(&client->dev, &sensor_dev_attr_temp##offset##_max.dev_attr); \
|
|
device_create_file(&client->dev, \
|
|
&sensor_dev_attr_temp##offset##_max_hyst.dev_attr); \
|
|
} while (0)
|
|
|
|
|
|
/* get reatime status of all sensors items: voltage, temp, fan */
|
|
static ssize_t
|
|
show_alarms_reg(struct device *dev, struct device_attribute *attr, char *buf)
|
|
{
|
|
struct w83792d_data *data = w83792d_update_device(dev);
|
|
return sprintf(buf, "%d\n", data->alarms);
|
|
}
|
|
|
|
static
|
|
DEVICE_ATTR(alarms, S_IRUGO, show_alarms_reg, NULL);
|
|
#define device_create_file_alarms(client) \
|
|
device_create_file(&client->dev, &dev_attr_alarms);
|
|
|
|
|
|
|
|
static ssize_t
|
|
show_pwm(struct device *dev, struct device_attribute *attr,
|
|
char *buf)
|
|
{
|
|
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
|
|
int nr = sensor_attr->index;
|
|
struct w83792d_data *data = w83792d_update_device(dev);
|
|
return sprintf(buf, "%ld\n", (long) PWM_FROM_REG(data->pwm[nr-1]));
|
|
}
|
|
|
|
static ssize_t
|
|
show_pwmenable(struct device *dev, struct device_attribute *attr,
|
|
char *buf)
|
|
{
|
|
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
|
|
int nr = sensor_attr->index - 1;
|
|
struct w83792d_data *data = w83792d_update_device(dev);
|
|
long pwm_enable_tmp = 1;
|
|
|
|
switch (data->pwmenable[nr]) {
|
|
case 0:
|
|
pwm_enable_tmp = 1; /* manual mode */
|
|
break;
|
|
case 1:
|
|
pwm_enable_tmp = 3; /*thermal cruise/Smart Fan I */
|
|
break;
|
|
case 2:
|
|
pwm_enable_tmp = 2; /* Smart Fan II */
|
|
break;
|
|
}
|
|
|
|
return sprintf(buf, "%ld\n", pwm_enable_tmp);
|
|
}
|
|
|
|
static ssize_t
|
|
store_pwm(struct device *dev, struct device_attribute *attr,
|
|
const char *buf, size_t count)
|
|
{
|
|
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
|
|
int nr = sensor_attr->index - 1;
|
|
struct i2c_client *client = to_i2c_client(dev);
|
|
struct w83792d_data *data = i2c_get_clientdata(client);
|
|
u32 val;
|
|
|
|
val = simple_strtoul(buf, NULL, 10);
|
|
data->pwm[nr] = PWM_TO_REG(val);
|
|
w83792d_write_value(client, W83792D_REG_PWM[nr], data->pwm[nr]);
|
|
|
|
return count;
|
|
}
|
|
|
|
static ssize_t
|
|
store_pwmenable(struct device *dev, struct device_attribute *attr,
|
|
const char *buf, size_t count)
|
|
{
|
|
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
|
|
int nr = sensor_attr->index - 1;
|
|
struct i2c_client *client = to_i2c_client(dev);
|
|
struct w83792d_data *data = i2c_get_clientdata(client);
|
|
u32 val;
|
|
u8 fan_cfg_tmp, cfg1_tmp, cfg2_tmp, cfg3_tmp, cfg4_tmp;
|
|
|
|
val = simple_strtoul(buf, NULL, 10);
|
|
switch (val) {
|
|
case 1:
|
|
data->pwmenable[nr] = 0; /* manual mode */
|
|
break;
|
|
case 2:
|
|
data->pwmenable[nr] = 2; /* Smart Fan II */
|
|
break;
|
|
case 3:
|
|
data->pwmenable[nr] = 1; /* thermal cruise/Smart Fan I */
|
|
break;
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
cfg1_tmp = data->pwmenable[0];
|
|
cfg2_tmp = (data->pwmenable[1]) << 2;
|
|
cfg3_tmp = (data->pwmenable[2]) << 4;
|
|
cfg4_tmp = w83792d_read_value(client,W83792D_REG_FAN_CFG) & 0xc0;
|
|
fan_cfg_tmp = ((cfg4_tmp | cfg3_tmp) | cfg2_tmp) | cfg1_tmp;
|
|
w83792d_write_value(client, W83792D_REG_FAN_CFG, fan_cfg_tmp);
|
|
|
|
return count;
|
|
}
|
|
|
|
#define sysfs_pwm(offset) \
|
|
static SENSOR_DEVICE_ATTR(pwm##offset, S_IRUGO | S_IWUSR, \
|
|
show_pwm, store_pwm, offset); \
|
|
static SENSOR_DEVICE_ATTR(pwm##offset##_enable, S_IRUGO | S_IWUSR, \
|
|
show_pwmenable, store_pwmenable, offset); \
|
|
|
|
sysfs_pwm(1);
|
|
sysfs_pwm(2);
|
|
sysfs_pwm(3);
|
|
|
|
|
|
#define device_create_file_pwm(client, offset) \
|
|
do { \
|
|
device_create_file(&client->dev, &sensor_dev_attr_pwm##offset.dev_attr); \
|
|
} while (0)
|
|
|
|
#define device_create_file_pwmenable(client, offset) \
|
|
do { \
|
|
device_create_file(&client->dev, &sensor_dev_attr_pwm##offset##_enable.dev_attr); \
|
|
} while (0)
|
|
|
|
|
|
static ssize_t
|
|
show_pwm_mode(struct device *dev, struct device_attribute *attr,
|
|
char *buf)
|
|
{
|
|
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
|
|
int nr = sensor_attr->index;
|
|
struct w83792d_data *data = w83792d_update_device(dev);
|
|
return sprintf(buf, "%d\n", data->pwm_mode[nr-1]);
|
|
}
|
|
|
|
static ssize_t
|
|
store_pwm_mode(struct device *dev, struct device_attribute *attr,
|
|
const char *buf, size_t count)
|
|
{
|
|
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
|
|
int nr = sensor_attr->index - 1;
|
|
struct i2c_client *client = to_i2c_client(dev);
|
|
struct w83792d_data *data = i2c_get_clientdata(client);
|
|
u32 val;
|
|
u8 pwm_mode_mask = 0;
|
|
|
|
val = simple_strtoul(buf, NULL, 10);
|
|
data->pwm_mode[nr] = SENSORS_LIMIT(val, 0, 1);
|
|
pwm_mode_mask = w83792d_read_value(client,
|
|
W83792D_REG_PWM[nr]) & 0x7f;
|
|
w83792d_write_value(client, W83792D_REG_PWM[nr],
|
|
((data->pwm_mode[nr]) << 7) | pwm_mode_mask);
|
|
|
|
return count;
|
|
}
|
|
|
|
#define sysfs_pwm_mode(offset) \
|
|
static SENSOR_DEVICE_ATTR(pwm##offset##_mode, S_IRUGO | S_IWUSR, \
|
|
show_pwm_mode, store_pwm_mode, offset);
|
|
|
|
sysfs_pwm_mode(1);
|
|
sysfs_pwm_mode(2);
|
|
sysfs_pwm_mode(3);
|
|
|
|
#define device_create_file_pwm_mode(client, offset) \
|
|
do { \
|
|
device_create_file(&client->dev, &sensor_dev_attr_pwm##offset##_mode.dev_attr); \
|
|
} while (0)
|
|
|
|
|
|
static ssize_t
|
|
show_regs_chassis(struct device *dev, struct device_attribute *attr,
|
|
char *buf)
|
|
{
|
|
struct w83792d_data *data = w83792d_update_device(dev);
|
|
return sprintf(buf, "%d\n", data->chassis);
|
|
}
|
|
|
|
static DEVICE_ATTR(chassis, S_IRUGO, show_regs_chassis, NULL);
|
|
|
|
#define device_create_file_chassis(client) \
|
|
do { \
|
|
device_create_file(&client->dev, &dev_attr_chassis); \
|
|
} while (0)
|
|
|
|
|
|
static ssize_t
|
|
show_chassis_clear(struct device *dev, struct device_attribute *attr, char *buf)
|
|
{
|
|
struct w83792d_data *data = w83792d_update_device(dev);
|
|
return sprintf(buf, "%d\n", data->chassis_clear);
|
|
}
|
|
|
|
static ssize_t
|
|
store_chassis_clear(struct device *dev, struct device_attribute *attr,
|
|
const char *buf, size_t count)
|
|
{
|
|
struct i2c_client *client = to_i2c_client(dev);
|
|
struct w83792d_data *data = i2c_get_clientdata(client);
|
|
u32 val;
|
|
u8 temp1 = 0, temp2 = 0;
|
|
|
|
val = simple_strtoul(buf, NULL, 10);
|
|
|
|
data->chassis_clear = SENSORS_LIMIT(val, 0 ,1);
|
|
temp1 = ((data->chassis_clear) << 7) & 0x80;
|
|
temp2 = w83792d_read_value(client,
|
|
W83792D_REG_CHASSIS_CLR) & 0x7f;
|
|
w83792d_write_value(client, W83792D_REG_CHASSIS_CLR, temp1 | temp2);
|
|
|
|
return count;
|
|
}
|
|
|
|
static DEVICE_ATTR(chassis_clear, S_IRUGO | S_IWUSR,
|
|
show_chassis_clear, store_chassis_clear);
|
|
|
|
#define device_create_file_chassis_clear(client) \
|
|
do { \
|
|
device_create_file(&client->dev, &dev_attr_chassis_clear); \
|
|
} while (0)
|
|
|
|
|
|
|
|
/* For Smart Fan I / Thermal Cruise */
|
|
static ssize_t
|
|
show_thermal_cruise(struct device *dev, struct device_attribute *attr,
|
|
char *buf)
|
|
{
|
|
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
|
|
int nr = sensor_attr->index;
|
|
struct w83792d_data *data = w83792d_update_device(dev);
|
|
return sprintf(buf, "%ld\n", (long)data->thermal_cruise[nr-1]);
|
|
}
|
|
|
|
static ssize_t
|
|
store_thermal_cruise(struct device *dev, struct device_attribute *attr,
|
|
const char *buf, size_t count)
|
|
{
|
|
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
|
|
int nr = sensor_attr->index - 1;
|
|
struct i2c_client *client = to_i2c_client(dev);
|
|
struct w83792d_data *data = i2c_get_clientdata(client);
|
|
u32 val;
|
|
u8 target_tmp=0, target_mask=0;
|
|
|
|
val = simple_strtoul(buf, NULL, 10);
|
|
target_tmp = val;
|
|
target_tmp = target_tmp & 0x7f;
|
|
target_mask = w83792d_read_value(client, W83792D_REG_THERMAL[nr]) & 0x80;
|
|
data->thermal_cruise[nr] = SENSORS_LIMIT(target_tmp, 0, 255);
|
|
w83792d_write_value(client, W83792D_REG_THERMAL[nr],
|
|
(data->thermal_cruise[nr]) | target_mask);
|
|
|
|
return count;
|
|
}
|
|
|
|
#define sysfs_thermal_cruise(offset) \
|
|
static SENSOR_DEVICE_ATTR(thermal_cruise##offset, S_IRUGO | S_IWUSR, \
|
|
show_thermal_cruise, store_thermal_cruise, offset);
|
|
|
|
sysfs_thermal_cruise(1);
|
|
sysfs_thermal_cruise(2);
|
|
sysfs_thermal_cruise(3);
|
|
|
|
#define device_create_file_thermal_cruise(client, offset) \
|
|
do { \
|
|
device_create_file(&client->dev, \
|
|
&sensor_dev_attr_thermal_cruise##offset.dev_attr); \
|
|
} while (0)
|
|
|
|
|
|
/* For Smart Fan I/Thermal Cruise and Smart Fan II */
|
|
static ssize_t
|
|
show_tolerance(struct device *dev, struct device_attribute *attr,
|
|
char *buf)
|
|
{
|
|
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
|
|
int nr = sensor_attr->index;
|
|
struct w83792d_data *data = w83792d_update_device(dev);
|
|
return sprintf(buf, "%ld\n", (long)data->tolerance[nr-1]);
|
|
}
|
|
|
|
static ssize_t
|
|
store_tolerance(struct device *dev, struct device_attribute *attr,
|
|
const char *buf, size_t count)
|
|
{
|
|
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
|
|
int nr = sensor_attr->index - 1;
|
|
struct i2c_client *client = to_i2c_client(dev);
|
|
struct w83792d_data *data = i2c_get_clientdata(client);
|
|
u32 val;
|
|
u8 tol_tmp, tol_mask;
|
|
|
|
val = simple_strtoul(buf, NULL, 10);
|
|
tol_mask = w83792d_read_value(client,
|
|
W83792D_REG_TOLERANCE[nr]) & ((nr == 1) ? 0x0f : 0xf0);
|
|
tol_tmp = SENSORS_LIMIT(val, 0, 15);
|
|
tol_tmp &= 0x0f;
|
|
data->tolerance[nr] = tol_tmp;
|
|
if (nr == 1) {
|
|
tol_tmp <<= 4;
|
|
}
|
|
w83792d_write_value(client, W83792D_REG_TOLERANCE[nr],
|
|
tol_mask | tol_tmp);
|
|
|
|
return count;
|
|
}
|
|
|
|
#define sysfs_tolerance(offset) \
|
|
static SENSOR_DEVICE_ATTR(tolerance##offset, S_IRUGO | S_IWUSR, \
|
|
show_tolerance, store_tolerance, offset);
|
|
|
|
sysfs_tolerance(1);
|
|
sysfs_tolerance(2);
|
|
sysfs_tolerance(3);
|
|
|
|
#define device_create_file_tolerance(client, offset) \
|
|
do { \
|
|
device_create_file(&client->dev, &sensor_dev_attr_tolerance##offset.dev_attr); \
|
|
} while (0)
|
|
|
|
|
|
/* For Smart Fan II */
|
|
static ssize_t
|
|
show_sf2_point(struct device *dev, struct device_attribute *attr,
|
|
char *buf)
|
|
{
|
|
struct sensor_device_attribute_2 *sensor_attr = to_sensor_dev_attr_2(attr);
|
|
int nr = sensor_attr->nr;
|
|
int index = sensor_attr->index;
|
|
struct w83792d_data *data = w83792d_update_device(dev);
|
|
return sprintf(buf, "%ld\n", (long)data->sf2_points[index-1][nr-1]);
|
|
}
|
|
|
|
static ssize_t
|
|
store_sf2_point(struct device *dev, struct device_attribute *attr,
|
|
const char *buf, size_t count)
|
|
{
|
|
struct sensor_device_attribute_2 *sensor_attr = to_sensor_dev_attr_2(attr);
|
|
int nr = sensor_attr->nr - 1;
|
|
int index = sensor_attr->index - 1;
|
|
struct i2c_client *client = to_i2c_client(dev);
|
|
struct w83792d_data *data = i2c_get_clientdata(client);
|
|
u32 val;
|
|
u8 mask_tmp = 0;
|
|
|
|
val = simple_strtoul(buf, NULL, 10);
|
|
data->sf2_points[index][nr] = SENSORS_LIMIT(val, 0, 127);
|
|
mask_tmp = w83792d_read_value(client,
|
|
W83792D_REG_POINTS[index][nr]) & 0x80;
|
|
w83792d_write_value(client, W83792D_REG_POINTS[index][nr],
|
|
mask_tmp|data->sf2_points[index][nr]);
|
|
|
|
return count;
|
|
}
|
|
|
|
#define sysfs_sf2_point(offset, index) \
|
|
static SENSOR_DEVICE_ATTR_2(sf2_point##offset##_fan##index, S_IRUGO | S_IWUSR, \
|
|
show_sf2_point, store_sf2_point, offset, index);
|
|
|
|
sysfs_sf2_point(1, 1); /* Fan1 */
|
|
sysfs_sf2_point(2, 1); /* Fan1 */
|
|
sysfs_sf2_point(3, 1); /* Fan1 */
|
|
sysfs_sf2_point(4, 1); /* Fan1 */
|
|
sysfs_sf2_point(1, 2); /* Fan2 */
|
|
sysfs_sf2_point(2, 2); /* Fan2 */
|
|
sysfs_sf2_point(3, 2); /* Fan2 */
|
|
sysfs_sf2_point(4, 2); /* Fan2 */
|
|
sysfs_sf2_point(1, 3); /* Fan3 */
|
|
sysfs_sf2_point(2, 3); /* Fan3 */
|
|
sysfs_sf2_point(3, 3); /* Fan3 */
|
|
sysfs_sf2_point(4, 3); /* Fan3 */
|
|
|
|
#define device_create_file_sf2_point(client, offset, index) \
|
|
do { \
|
|
device_create_file(&client->dev, \
|
|
&sensor_dev_attr_sf2_point##offset##_fan##index.dev_attr); \
|
|
} while (0)
|
|
|
|
|
|
static ssize_t
|
|
show_sf2_level(struct device *dev, struct device_attribute *attr,
|
|
char *buf)
|
|
{
|
|
struct sensor_device_attribute_2 *sensor_attr = to_sensor_dev_attr_2(attr);
|
|
int nr = sensor_attr->nr;
|
|
int index = sensor_attr->index;
|
|
struct w83792d_data *data = w83792d_update_device(dev);
|
|
return sprintf(buf, "%d\n",
|
|
(((data->sf2_levels[index-1][nr]) * 100) / 15));
|
|
}
|
|
|
|
static ssize_t
|
|
store_sf2_level(struct device *dev, struct device_attribute *attr,
|
|
const char *buf, size_t count)
|
|
{
|
|
struct sensor_device_attribute_2 *sensor_attr = to_sensor_dev_attr_2(attr);
|
|
int nr = sensor_attr->nr;
|
|
int index = sensor_attr->index - 1;
|
|
struct i2c_client *client = to_i2c_client(dev);
|
|
struct w83792d_data *data = i2c_get_clientdata(client);
|
|
u32 val;
|
|
u8 mask_tmp=0, level_tmp=0;
|
|
|
|
val = simple_strtoul(buf, NULL, 10);
|
|
data->sf2_levels[index][nr] = SENSORS_LIMIT((val * 15) / 100, 0, 15);
|
|
mask_tmp = w83792d_read_value(client, W83792D_REG_LEVELS[index][nr])
|
|
& ((nr==3) ? 0xf0 : 0x0f);
|
|
if (nr==3) {
|
|
level_tmp = data->sf2_levels[index][nr];
|
|
} else {
|
|
level_tmp = data->sf2_levels[index][nr] << 4;
|
|
}
|
|
w83792d_write_value(client, W83792D_REG_LEVELS[index][nr], level_tmp | mask_tmp);
|
|
|
|
return count;
|
|
}
|
|
|
|
#define sysfs_sf2_level(offset, index) \
|
|
static SENSOR_DEVICE_ATTR_2(sf2_level##offset##_fan##index, S_IRUGO | S_IWUSR, \
|
|
show_sf2_level, store_sf2_level, offset, index);
|
|
|
|
sysfs_sf2_level(1, 1); /* Fan1 */
|
|
sysfs_sf2_level(2, 1); /* Fan1 */
|
|
sysfs_sf2_level(3, 1); /* Fan1 */
|
|
sysfs_sf2_level(1, 2); /* Fan2 */
|
|
sysfs_sf2_level(2, 2); /* Fan2 */
|
|
sysfs_sf2_level(3, 2); /* Fan2 */
|
|
sysfs_sf2_level(1, 3); /* Fan3 */
|
|
sysfs_sf2_level(2, 3); /* Fan3 */
|
|
sysfs_sf2_level(3, 3); /* Fan3 */
|
|
|
|
#define device_create_file_sf2_level(client, offset, index) \
|
|
do { \
|
|
device_create_file(&client->dev, \
|
|
&sensor_dev_attr_sf2_level##offset##_fan##index.dev_attr); \
|
|
} while (0)
|
|
|
|
|
|
/* This function is called when:
|
|
* w83792d_driver is inserted (when this module is loaded), for each
|
|
available adapter
|
|
* when a new adapter is inserted (and w83792d_driver is still present) */
|
|
static int
|
|
w83792d_attach_adapter(struct i2c_adapter *adapter)
|
|
{
|
|
if (!(adapter->class & I2C_CLASS_HWMON))
|
|
return 0;
|
|
return i2c_probe(adapter, &addr_data, w83792d_detect);
|
|
}
|
|
|
|
|
|
static int
|
|
w83792d_create_subclient(struct i2c_adapter *adapter,
|
|
struct i2c_client *new_client, int addr,
|
|
struct i2c_client **sub_cli)
|
|
{
|
|
int err;
|
|
struct i2c_client *sub_client;
|
|
|
|
(*sub_cli) = sub_client = kzalloc(sizeof(struct i2c_client), GFP_KERNEL);
|
|
if (!(sub_client)) {
|
|
return -ENOMEM;
|
|
}
|
|
sub_client->addr = 0x48 + addr;
|
|
i2c_set_clientdata(sub_client, NULL);
|
|
sub_client->adapter = adapter;
|
|
sub_client->driver = &w83792d_driver;
|
|
sub_client->flags = 0;
|
|
strlcpy(sub_client->name, "w83792d subclient", I2C_NAME_SIZE);
|
|
if ((err = i2c_attach_client(sub_client))) {
|
|
dev_err(&new_client->dev, "subclient registration "
|
|
"at address 0x%x failed\n", sub_client->addr);
|
|
kfree(sub_client);
|
|
return err;
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
|
|
static int
|
|
w83792d_detect_subclients(struct i2c_adapter *adapter, int address, int kind,
|
|
struct i2c_client *new_client)
|
|
{
|
|
int i, id, err;
|
|
u8 val;
|
|
struct w83792d_data *data = i2c_get_clientdata(new_client);
|
|
|
|
id = i2c_adapter_id(adapter);
|
|
if (force_subclients[0] == id && force_subclients[1] == address) {
|
|
for (i = 2; i <= 3; i++) {
|
|
if (force_subclients[i] < 0x48 ||
|
|
force_subclients[i] > 0x4f) {
|
|
dev_err(&new_client->dev, "invalid subclient "
|
|
"address %d; must be 0x48-0x4f\n",
|
|
force_subclients[i]);
|
|
err = -ENODEV;
|
|
goto ERROR_SC_0;
|
|
}
|
|
}
|
|
w83792d_write_value(new_client, W83792D_REG_I2C_SUBADDR,
|
|
(force_subclients[2] & 0x07) |
|
|
((force_subclients[3] & 0x07) << 4));
|
|
}
|
|
|
|
val = w83792d_read_value(new_client, W83792D_REG_I2C_SUBADDR);
|
|
if (!(val & 0x08)) {
|
|
err = w83792d_create_subclient(adapter, new_client, val & 0x7,
|
|
&data->lm75[0]);
|
|
if (err < 0)
|
|
goto ERROR_SC_0;
|
|
}
|
|
if (!(val & 0x80)) {
|
|
if ((data->lm75[0] != NULL) &&
|
|
((val & 0x7) == ((val >> 4) & 0x7))) {
|
|
dev_err(&new_client->dev, "duplicate addresses 0x%x, "
|
|
"use force_subclient\n", data->lm75[0]->addr);
|
|
err = -ENODEV;
|
|
goto ERROR_SC_1;
|
|
}
|
|
err = w83792d_create_subclient(adapter, new_client,
|
|
(val >> 4) & 0x7, &data->lm75[1]);
|
|
if (err < 0)
|
|
goto ERROR_SC_1;
|
|
}
|
|
|
|
return 0;
|
|
|
|
/* Undo inits in case of errors */
|
|
|
|
ERROR_SC_1:
|
|
if (data->lm75[0] != NULL) {
|
|
i2c_detach_client(data->lm75[0]);
|
|
kfree(data->lm75[0]);
|
|
}
|
|
ERROR_SC_0:
|
|
return err;
|
|
}
|
|
|
|
|
|
static int
|
|
w83792d_detect(struct i2c_adapter *adapter, int address, int kind)
|
|
{
|
|
int i = 0, val1 = 0, val2;
|
|
struct i2c_client *new_client;
|
|
struct w83792d_data *data;
|
|
int err = 0;
|
|
const char *client_name = "";
|
|
|
|
if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) {
|
|
goto ERROR0;
|
|
}
|
|
|
|
/* OK. For now, we presume we have a valid client. We now create the
|
|
client structure, even though we cannot fill it completely yet.
|
|
But it allows us to access w83792d_{read,write}_value. */
|
|
|
|
if (!(data = kzalloc(sizeof(struct w83792d_data), GFP_KERNEL))) {
|
|
err = -ENOMEM;
|
|
goto ERROR0;
|
|
}
|
|
|
|
new_client = &data->client;
|
|
i2c_set_clientdata(new_client, data);
|
|
new_client->addr = address;
|
|
init_MUTEX(&data->lock);
|
|
new_client->adapter = adapter;
|
|
new_client->driver = &w83792d_driver;
|
|
new_client->flags = 0;
|
|
|
|
/* Now, we do the remaining detection. */
|
|
|
|
/* The w83792d may be stuck in some other bank than bank 0. This may
|
|
make reading other information impossible. Specify a force=... or
|
|
force_*=... parameter, and the Winbond will be reset to the right
|
|
bank. */
|
|
if (kind < 0) {
|
|
if (w83792d_read_value(new_client, W83792D_REG_CONFIG) & 0x80) {
|
|
dev_warn(&new_client->dev, "Detection failed at step "
|
|
"3\n");
|
|
goto ERROR1;
|
|
}
|
|
val1 = w83792d_read_value(new_client, W83792D_REG_BANK);
|
|
val2 = w83792d_read_value(new_client, W83792D_REG_CHIPMAN);
|
|
/* Check for Winbond ID if in bank 0 */
|
|
if (!(val1 & 0x07)) { /* is Bank0 */
|
|
if (((!(val1 & 0x80)) && (val2 != 0xa3)) ||
|
|
((val1 & 0x80) && (val2 != 0x5c))) {
|
|
goto ERROR1;
|
|
}
|
|
}
|
|
/* If Winbond chip, address of chip and W83792D_REG_I2C_ADDR
|
|
should match */
|
|
if (w83792d_read_value(new_client,
|
|
W83792D_REG_I2C_ADDR) != address) {
|
|
dev_warn(&new_client->dev, "Detection failed "
|
|
"at step 5\n");
|
|
goto ERROR1;
|
|
}
|
|
}
|
|
|
|
/* We have either had a force parameter, or we have already detected the
|
|
Winbond. Put it now into bank 0 and Vendor ID High Byte */
|
|
w83792d_write_value(new_client,
|
|
W83792D_REG_BANK,
|
|
(w83792d_read_value(new_client,
|
|
W83792D_REG_BANK) & 0x78) | 0x80);
|
|
|
|
/* Determine the chip type. */
|
|
if (kind <= 0) {
|
|
/* get vendor ID */
|
|
val2 = w83792d_read_value(new_client, W83792D_REG_CHIPMAN);
|
|
if (val2 != 0x5c) { /* the vendor is NOT Winbond */
|
|
goto ERROR1;
|
|
}
|
|
val1 = w83792d_read_value(new_client, W83792D_REG_WCHIPID);
|
|
if (val1 == 0x7a && address >= 0x2c) {
|
|
kind = w83792d;
|
|
} else {
|
|
if (kind == 0)
|
|
dev_warn(&new_client->dev,
|
|
"w83792d: Ignoring 'force' parameter for"
|
|
" unknown chip at adapter %d, address"
|
|
" 0x%02x\n", i2c_adapter_id(adapter),
|
|
address);
|
|
goto ERROR1;
|
|
}
|
|
}
|
|
|
|
if (kind == w83792d) {
|
|
client_name = "w83792d";
|
|
} else {
|
|
dev_err(&new_client->dev, "w83792d: Internal error: unknown"
|
|
" kind (%d)?!?", kind);
|
|
goto ERROR1;
|
|
}
|
|
|
|
/* Fill in the remaining client fields and put into the global list */
|
|
strlcpy(new_client->name, client_name, I2C_NAME_SIZE);
|
|
data->type = kind;
|
|
|
|
data->valid = 0;
|
|
init_MUTEX(&data->update_lock);
|
|
|
|
/* Tell the I2C layer a new client has arrived */
|
|
if ((err = i2c_attach_client(new_client)))
|
|
goto ERROR1;
|
|
|
|
if ((err = w83792d_detect_subclients(adapter, address,
|
|
kind, new_client)))
|
|
goto ERROR2;
|
|
|
|
/* Initialize the chip */
|
|
w83792d_init_client(new_client);
|
|
|
|
/* A few vars need to be filled upon startup */
|
|
for (i = 0; i < 7; i++) {
|
|
data->fan_min[i] = w83792d_read_value(new_client,
|
|
W83792D_REG_FAN_MIN[i]);
|
|
}
|
|
|
|
/* Register sysfs hooks */
|
|
data->class_dev = hwmon_device_register(&new_client->dev);
|
|
if (IS_ERR(data->class_dev)) {
|
|
err = PTR_ERR(data->class_dev);
|
|
goto ERROR3;
|
|
}
|
|
device_create_file_in(new_client, 0);
|
|
device_create_file_in(new_client, 1);
|
|
device_create_file_in(new_client, 2);
|
|
device_create_file_in(new_client, 3);
|
|
device_create_file_in(new_client, 4);
|
|
device_create_file_in(new_client, 5);
|
|
device_create_file_in(new_client, 6);
|
|
device_create_file_in(new_client, 7);
|
|
device_create_file_in(new_client, 8);
|
|
|
|
device_create_file_fan(new_client, 1);
|
|
device_create_file_fan(new_client, 2);
|
|
device_create_file_fan(new_client, 3);
|
|
|
|
/* Read GPIO enable register to check if pins for fan 4,5 are used as
|
|
GPIO */
|
|
val1 = w83792d_read_value(new_client, W83792D_REG_GPIO_EN);
|
|
if (!(val1 & 0x40))
|
|
device_create_file_fan(new_client, 4);
|
|
if (!(val1 & 0x20))
|
|
device_create_file_fan(new_client, 5);
|
|
|
|
val1 = w83792d_read_value(new_client, W83792D_REG_PIN);
|
|
if (val1 & 0x40)
|
|
device_create_file_fan(new_client, 6);
|
|
if (val1 & 0x04)
|
|
device_create_file_fan(new_client, 7);
|
|
|
|
device_create_file_temp1(new_client); /* Temp1 */
|
|
device_create_file_temp_add(new_client, 2); /* Temp2 */
|
|
device_create_file_temp_add(new_client, 3); /* Temp3 */
|
|
|
|
device_create_file_alarms(new_client);
|
|
|
|
device_create_file_pwm(new_client, 1);
|
|
device_create_file_pwm(new_client, 2);
|
|
device_create_file_pwm(new_client, 3);
|
|
|
|
device_create_file_pwmenable(new_client, 1);
|
|
device_create_file_pwmenable(new_client, 2);
|
|
device_create_file_pwmenable(new_client, 3);
|
|
|
|
device_create_file_pwm_mode(new_client, 1);
|
|
device_create_file_pwm_mode(new_client, 2);
|
|
device_create_file_pwm_mode(new_client, 3);
|
|
|
|
device_create_file_chassis(new_client);
|
|
device_create_file_chassis_clear(new_client);
|
|
|
|
device_create_file_thermal_cruise(new_client, 1);
|
|
device_create_file_thermal_cruise(new_client, 2);
|
|
device_create_file_thermal_cruise(new_client, 3);
|
|
|
|
device_create_file_tolerance(new_client, 1);
|
|
device_create_file_tolerance(new_client, 2);
|
|
device_create_file_tolerance(new_client, 3);
|
|
|
|
device_create_file_sf2_point(new_client, 1, 1); /* Fan1 */
|
|
device_create_file_sf2_point(new_client, 2, 1); /* Fan1 */
|
|
device_create_file_sf2_point(new_client, 3, 1); /* Fan1 */
|
|
device_create_file_sf2_point(new_client, 4, 1); /* Fan1 */
|
|
device_create_file_sf2_point(new_client, 1, 2); /* Fan2 */
|
|
device_create_file_sf2_point(new_client, 2, 2); /* Fan2 */
|
|
device_create_file_sf2_point(new_client, 3, 2); /* Fan2 */
|
|
device_create_file_sf2_point(new_client, 4, 2); /* Fan2 */
|
|
device_create_file_sf2_point(new_client, 1, 3); /* Fan3 */
|
|
device_create_file_sf2_point(new_client, 2, 3); /* Fan3 */
|
|
device_create_file_sf2_point(new_client, 3, 3); /* Fan3 */
|
|
device_create_file_sf2_point(new_client, 4, 3); /* Fan3 */
|
|
|
|
device_create_file_sf2_level(new_client, 1, 1); /* Fan1 */
|
|
device_create_file_sf2_level(new_client, 2, 1); /* Fan1 */
|
|
device_create_file_sf2_level(new_client, 3, 1); /* Fan1 */
|
|
device_create_file_sf2_level(new_client, 1, 2); /* Fan2 */
|
|
device_create_file_sf2_level(new_client, 2, 2); /* Fan2 */
|
|
device_create_file_sf2_level(new_client, 3, 2); /* Fan2 */
|
|
device_create_file_sf2_level(new_client, 1, 3); /* Fan3 */
|
|
device_create_file_sf2_level(new_client, 2, 3); /* Fan3 */
|
|
device_create_file_sf2_level(new_client, 3, 3); /* Fan3 */
|
|
|
|
return 0;
|
|
|
|
ERROR3:
|
|
if (data->lm75[0] != NULL) {
|
|
i2c_detach_client(data->lm75[0]);
|
|
kfree(data->lm75[0]);
|
|
}
|
|
if (data->lm75[1] != NULL) {
|
|
i2c_detach_client(data->lm75[1]);
|
|
kfree(data->lm75[1]);
|
|
}
|
|
ERROR2:
|
|
i2c_detach_client(new_client);
|
|
ERROR1:
|
|
kfree(data);
|
|
ERROR0:
|
|
return err;
|
|
}
|
|
|
|
static int
|
|
w83792d_detach_client(struct i2c_client *client)
|
|
{
|
|
struct w83792d_data *data = i2c_get_clientdata(client);
|
|
int err;
|
|
|
|
/* main client */
|
|
if (data)
|
|
hwmon_device_unregister(data->class_dev);
|
|
|
|
if ((err = i2c_detach_client(client)))
|
|
return err;
|
|
|
|
/* main client */
|
|
if (data)
|
|
kfree(data);
|
|
/* subclient */
|
|
else
|
|
kfree(client);
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* The SMBus locks itself, usually, but nothing may access the Winbond between
|
|
bank switches. ISA access must always be locked explicitly!
|
|
We ignore the W83792D BUSY flag at this moment - it could lead to deadlocks,
|
|
would slow down the W83792D access and should not be necessary.
|
|
There are some ugly typecasts here, but the good news is - they should
|
|
nowhere else be necessary! */
|
|
static int
|
|
w83792d_read_value(struct i2c_client *client, u8 reg)
|
|
{
|
|
int res=0;
|
|
res = i2c_smbus_read_byte_data(client, reg);
|
|
|
|
return res;
|
|
}
|
|
|
|
static int
|
|
w83792d_write_value(struct i2c_client *client, u8 reg, u8 value)
|
|
{
|
|
i2c_smbus_write_byte_data(client, reg, value);
|
|
return 0;
|
|
}
|
|
|
|
static void
|
|
w83792d_init_client(struct i2c_client *client)
|
|
{
|
|
u8 temp2_cfg, temp3_cfg, vid_in_b;
|
|
|
|
if (init) {
|
|
w83792d_write_value(client, W83792D_REG_CONFIG, 0x80);
|
|
}
|
|
/* Clear the bit6 of W83792D_REG_VID_IN_B(set it into 0):
|
|
W83792D_REG_VID_IN_B bit6 = 0: the high/low limit of
|
|
vin0/vin1 can be modified by user;
|
|
W83792D_REG_VID_IN_B bit6 = 1: the high/low limit of
|
|
vin0/vin1 auto-updated, can NOT be modified by user. */
|
|
vid_in_b = w83792d_read_value(client, W83792D_REG_VID_IN_B);
|
|
w83792d_write_value(client, W83792D_REG_VID_IN_B,
|
|
vid_in_b & 0xbf);
|
|
|
|
temp2_cfg = w83792d_read_value(client, W83792D_REG_TEMP2_CONFIG);
|
|
temp3_cfg = w83792d_read_value(client, W83792D_REG_TEMP3_CONFIG);
|
|
w83792d_write_value(client, W83792D_REG_TEMP2_CONFIG,
|
|
temp2_cfg & 0xe6);
|
|
w83792d_write_value(client, W83792D_REG_TEMP3_CONFIG,
|
|
temp3_cfg & 0xe6);
|
|
|
|
/* Start monitoring */
|
|
w83792d_write_value(client, W83792D_REG_CONFIG,
|
|
(w83792d_read_value(client,
|
|
W83792D_REG_CONFIG) & 0xf7)
|
|
| 0x01);
|
|
}
|
|
|
|
static struct w83792d_data *w83792d_update_device(struct device *dev)
|
|
{
|
|
struct i2c_client *client = to_i2c_client(dev);
|
|
struct w83792d_data *data = i2c_get_clientdata(client);
|
|
int i, j;
|
|
u8 reg_array_tmp[4], pwm_array_tmp[7], reg_tmp;
|
|
|
|
down(&data->update_lock);
|
|
|
|
if (time_after
|
|
(jiffies - data->last_updated, (unsigned long) (HZ * 3))
|
|
|| time_before(jiffies, data->last_updated) || !data->valid) {
|
|
dev_dbg(dev, "Starting device update\n");
|
|
|
|
/* Update the voltages measured value and limits */
|
|
for (i = 0; i < 9; i++) {
|
|
data->in[i] = w83792d_read_value(client,
|
|
W83792D_REG_IN[i]);
|
|
data->in_max[i] = w83792d_read_value(client,
|
|
W83792D_REG_IN_MAX[i]);
|
|
data->in_min[i] = w83792d_read_value(client,
|
|
W83792D_REG_IN_MIN[i]);
|
|
}
|
|
data->low_bits[0] = w83792d_read_value(client,
|
|
W83792D_REG_LOW_BITS1);
|
|
data->low_bits[1] = w83792d_read_value(client,
|
|
W83792D_REG_LOW_BITS2);
|
|
for (i = 0; i < 7; i++) {
|
|
/* Update the Fan measured value and limits */
|
|
data->fan[i] = w83792d_read_value(client,
|
|
W83792D_REG_FAN[i]);
|
|
data->fan_min[i] = w83792d_read_value(client,
|
|
W83792D_REG_FAN_MIN[i]);
|
|
/* Update the PWM/DC Value and PWM/DC flag */
|
|
pwm_array_tmp[i] = w83792d_read_value(client,
|
|
W83792D_REG_PWM[i]);
|
|
data->pwm[i] = pwm_array_tmp[i] & 0x0f;
|
|
data->pwm_mode[i] = (pwm_array_tmp[i] >> 7) & 0x01;
|
|
}
|
|
|
|
reg_tmp = w83792d_read_value(client, W83792D_REG_FAN_CFG);
|
|
data->pwmenable[0] = reg_tmp & 0x03;
|
|
data->pwmenable[1] = (reg_tmp>>2) & 0x03;
|
|
data->pwmenable[2] = (reg_tmp>>4) & 0x03;
|
|
|
|
for (i = 0; i < 3; i++) {
|
|
data->temp1[i] = w83792d_read_value(client,
|
|
W83792D_REG_TEMP1[i]);
|
|
}
|
|
for (i = 0; i < 2; i++) {
|
|
for (j = 0; j < 6; j++) {
|
|
data->temp_add[i][j] = w83792d_read_value(
|
|
client,W83792D_REG_TEMP_ADD[i][j]);
|
|
}
|
|
}
|
|
|
|
/* Update the Fan Divisor */
|
|
for (i = 0; i < 4; i++) {
|
|
reg_array_tmp[i] = w83792d_read_value(client,
|
|
W83792D_REG_FAN_DIV[i]);
|
|
}
|
|
data->fan_div[0] = reg_array_tmp[0] & 0x07;
|
|
data->fan_div[1] = (reg_array_tmp[0] >> 4) & 0x07;
|
|
data->fan_div[2] = reg_array_tmp[1] & 0x07;
|
|
data->fan_div[3] = (reg_array_tmp[1] >> 4) & 0x07;
|
|
data->fan_div[4] = reg_array_tmp[2] & 0x07;
|
|
data->fan_div[5] = (reg_array_tmp[2] >> 4) & 0x07;
|
|
data->fan_div[6] = reg_array_tmp[3] & 0x07;
|
|
|
|
/* Update the realtime status */
|
|
data->alarms = w83792d_read_value(client, W83792D_REG_ALARM1) +
|
|
(w83792d_read_value(client, W83792D_REG_ALARM2) << 8) +
|
|
(w83792d_read_value(client, W83792D_REG_ALARM3) << 16);
|
|
|
|
/* Update CaseOpen status and it's CLR_CHS. */
|
|
data->chassis = (w83792d_read_value(client,
|
|
W83792D_REG_CHASSIS) >> 5) & 0x01;
|
|
data->chassis_clear = (w83792d_read_value(client,
|
|
W83792D_REG_CHASSIS_CLR) >> 7) & 0x01;
|
|
|
|
/* Update Thermal Cruise/Smart Fan I target value */
|
|
for (i = 0; i < 3; i++) {
|
|
data->thermal_cruise[i] =
|
|
w83792d_read_value(client,
|
|
W83792D_REG_THERMAL[i]) & 0x7f;
|
|
}
|
|
|
|
/* Update Smart Fan I/II tolerance */
|
|
reg_tmp = w83792d_read_value(client, W83792D_REG_TOLERANCE[0]);
|
|
data->tolerance[0] = reg_tmp & 0x0f;
|
|
data->tolerance[1] = (reg_tmp >> 4) & 0x0f;
|
|
data->tolerance[2] = w83792d_read_value(client,
|
|
W83792D_REG_TOLERANCE[2]) & 0x0f;
|
|
|
|
/* Update Smart Fan II temperature points */
|
|
for (i = 0; i < 3; i++) {
|
|
for (j = 0; j < 4; j++) {
|
|
data->sf2_points[i][j] = w83792d_read_value(
|
|
client,W83792D_REG_POINTS[i][j]) & 0x7f;
|
|
}
|
|
}
|
|
|
|
/* Update Smart Fan II duty cycle levels */
|
|
for (i = 0; i < 3; i++) {
|
|
reg_tmp = w83792d_read_value(client,
|
|
W83792D_REG_LEVELS[i][0]);
|
|
data->sf2_levels[i][0] = reg_tmp & 0x0f;
|
|
data->sf2_levels[i][1] = (reg_tmp >> 4) & 0x0f;
|
|
reg_tmp = w83792d_read_value(client,
|
|
W83792D_REG_LEVELS[i][2]);
|
|
data->sf2_levels[i][2] = (reg_tmp >> 4) & 0x0f;
|
|
data->sf2_levels[i][3] = reg_tmp & 0x0f;
|
|
}
|
|
|
|
data->last_updated = jiffies;
|
|
data->valid = 1;
|
|
}
|
|
|
|
up(&data->update_lock);
|
|
|
|
#ifdef DEBUG
|
|
w83792d_print_debug(data, dev);
|
|
#endif
|
|
|
|
return data;
|
|
}
|
|
|
|
#ifdef DEBUG
|
|
static void w83792d_print_debug(struct w83792d_data *data, struct device *dev)
|
|
{
|
|
int i=0, j=0;
|
|
dev_dbg(dev, "==========The following is the debug message...========\n");
|
|
dev_dbg(dev, "9 set of Voltages: =====>\n");
|
|
for (i=0; i<9; i++) {
|
|
dev_dbg(dev, "vin[%d] is: 0x%x\n", i, data->in[i]);
|
|
dev_dbg(dev, "vin[%d] max is: 0x%x\n", i, data->in_max[i]);
|
|
dev_dbg(dev, "vin[%d] min is: 0x%x\n", i, data->in_min[i]);
|
|
}
|
|
dev_dbg(dev, "Low Bit1 is: 0x%x\n", data->low_bits[0]);
|
|
dev_dbg(dev, "Low Bit2 is: 0x%x\n", data->low_bits[1]);
|
|
dev_dbg(dev, "7 set of Fan Counts and Duty Cycles: =====>\n");
|
|
for (i=0; i<7; i++) {
|
|
dev_dbg(dev, "fan[%d] is: 0x%x\n", i, data->fan[i]);
|
|
dev_dbg(dev, "fan[%d] min is: 0x%x\n", i, data->fan_min[i]);
|
|
dev_dbg(dev, "pwm[%d] is: 0x%x\n", i, data->pwm[i]);
|
|
dev_dbg(dev, "pwm_mode[%d] is: 0x%x\n", i, data->pwm_mode[i]);
|
|
}
|
|
dev_dbg(dev, "3 set of Temperatures: =====>\n");
|
|
for (i=0; i<3; i++) {
|
|
dev_dbg(dev, "temp1[%d] is: 0x%x\n", i, data->temp1[i]);
|
|
}
|
|
|
|
for (i=0; i<2; i++) {
|
|
for (j=0; j<6; j++) {
|
|
dev_dbg(dev, "temp_add[%d][%d] is: 0x%x\n", i, j,
|
|
data->temp_add[i][j]);
|
|
}
|
|
}
|
|
|
|
for (i=0; i<7; i++) {
|
|
dev_dbg(dev, "fan_div[%d] is: 0x%x\n", i, data->fan_div[i]);
|
|
}
|
|
dev_dbg(dev, "==========End of the debug message...==================\n");
|
|
dev_dbg(dev, "\n");
|
|
}
|
|
#endif
|
|
|
|
static int __init
|
|
sensors_w83792d_init(void)
|
|
{
|
|
return i2c_add_driver(&w83792d_driver);
|
|
}
|
|
|
|
static void __exit
|
|
sensors_w83792d_exit(void)
|
|
{
|
|
i2c_del_driver(&w83792d_driver);
|
|
}
|
|
|
|
MODULE_AUTHOR("Chunhao Huang @ Winbond <DZShen@Winbond.com.tw>");
|
|
MODULE_DESCRIPTION("W83792AD/D driver for linux-2.6");
|
|
MODULE_LICENSE("GPL");
|
|
|
|
module_init(sensors_w83792d_init);
|
|
module_exit(sensors_w83792d_exit);
|
|
|