113 lines
3.4 KiB
C
113 lines
3.4 KiB
C
/*
|
|
* linux/include/asm-arm/arch-sa1100/simpad.h
|
|
*
|
|
* based of assabet.h same as HUW_Webpanel
|
|
*
|
|
* This file contains the hardware specific definitions for SIMpad
|
|
*
|
|
* 2001/05/14 Juergen Messerer <juergen.messerer@freesurf.ch>
|
|
*/
|
|
|
|
#ifndef __ASM_ARCH_SIMPAD_H
|
|
#define __ASM_ARCH_SIMPAD_H
|
|
|
|
|
|
#define GPIO_UART1_RTS GPIO_GPIO14
|
|
#define GPIO_UART1_DTR GPIO_GPIO7
|
|
#define GPIO_UART1_CTS GPIO_GPIO8
|
|
#define GPIO_UART1_DCD GPIO_GPIO23
|
|
#define GPIO_UART1_DSR GPIO_GPIO6
|
|
|
|
#define GPIO_UART3_RTS GPIO_GPIO12
|
|
#define GPIO_UART3_DTR GPIO_GPIO16
|
|
#define GPIO_UART3_CTS GPIO_GPIO13
|
|
#define GPIO_UART3_DCD GPIO_GPIO18
|
|
#define GPIO_UART3_DSR GPIO_GPIO17
|
|
|
|
#define GPIO_POWER_BUTTON GPIO_GPIO0
|
|
#define GPIO_UCB1300_IRQ GPIO_GPIO22 /* UCB GPIO and touchscreen */
|
|
|
|
#define IRQ_UART1_CTS IRQ_GPIO15
|
|
#define IRQ_UART1_DCD GPIO_GPIO23
|
|
#define IRQ_UART1_DSR GPIO_GPIO6
|
|
#define IRQ_UART3_CTS GPIO_GPIO13
|
|
#define IRQ_UART3_DCD GPIO_GPIO18
|
|
#define IRQ_UART3_DSR GPIO_GPIO17
|
|
|
|
#define IRQ_GPIO_UCB1300_IRQ IRQ_GPIO22
|
|
#define IRQ_GPIO_POWER_BUTTON IRQ_GPIO0
|
|
|
|
|
|
/*--- PCMCIA ---*/
|
|
#define GPIO_CF_CD GPIO_GPIO24
|
|
#define GPIO_CF_IRQ GPIO_GPIO1
|
|
#define IRQ_GPIO_CF_IRQ IRQ_GPIO1
|
|
#define IRQ_GPIO_CF_CD IRQ_GPIO24
|
|
|
|
/*--- SmartCard ---*/
|
|
#define GPIO_SMART_CARD GPIO_GPIO10
|
|
#define IRQ_GPIO_SMARD_CARD IRQ_GPIO10
|
|
|
|
// CS3 Latch is write only, a shadow is necessary
|
|
|
|
#define CS3BUSTYPE unsigned volatile long
|
|
#define CS3_BASE 0xf1000000
|
|
|
|
#define VCC_5V_EN 0x0001 // For 5V PCMCIA
|
|
#define VCC_3V_EN 0x0002 // FOR 3.3V PCMCIA
|
|
#define EN1 0x0004 // This is only for EPROM's
|
|
#define EN0 0x0008 // Both should be enable for 3.3V or 5V
|
|
#define DISPLAY_ON 0x0010
|
|
#define PCMCIA_BUFF_DIS 0x0020
|
|
#define MQ_RESET 0x0040
|
|
#define PCMCIA_RESET 0x0080
|
|
#define DECT_POWER_ON 0x0100
|
|
#define IRDA_SD 0x0200 // Shutdown for powersave
|
|
#define RS232_ON 0x0400
|
|
#define SD_MEDIAQ 0x0800 // Shutdown for powersave
|
|
#define LED2_ON 0x1000
|
|
#define IRDA_MODE 0x2000 // Fast/Slow IrDA mode
|
|
#define ENABLE_5V 0x4000 // Enable 5V circuit
|
|
#define RESET_SIMCARD 0x8000
|
|
|
|
#define RS232_ENABLE 0x0440
|
|
#define PCMCIAMASK 0x402f
|
|
|
|
|
|
struct simpad_battery {
|
|
unsigned char ac_status; /* line connected yes/no */
|
|
unsigned char status; /* battery loading yes/no */
|
|
unsigned char percentage; /* percentage loaded */
|
|
unsigned short life; /* life till empty */
|
|
};
|
|
|
|
/* These should match the apm_bios.h definitions */
|
|
#define SIMPAD_AC_STATUS_AC_OFFLINE 0x00
|
|
#define SIMPAD_AC_STATUS_AC_ONLINE 0x01
|
|
#define SIMPAD_AC_STATUS_AC_BACKUP 0x02 /* What does this mean? */
|
|
#define SIMPAD_AC_STATUS_AC_UNKNOWN 0xff
|
|
|
|
/* These bitfields are rarely "or'd" together */
|
|
#define SIMPAD_BATT_STATUS_HIGH 0x01
|
|
#define SIMPAD_BATT_STATUS_LOW 0x02
|
|
#define SIMPAD_BATT_STATUS_CRITICAL 0x04
|
|
#define SIMPAD_BATT_STATUS_CHARGING 0x08
|
|
#define SIMPAD_BATT_STATUS_CHARGE_MAIN 0x10
|
|
#define SIMPAD_BATT_STATUS_DEAD 0x20 /* Battery will not charge */
|
|
#define SIMPAD_BATT_NOT_INSTALLED 0x20 /* For expansion pack batteries */
|
|
#define SIMPAD_BATT_STATUS_FULL 0x40 /* Battery fully charged (and connected to AC) */
|
|
#define SIMPAD_BATT_STATUS_NOBATT 0x80
|
|
#define SIMPAD_BATT_STATUS_UNKNOWN 0xff
|
|
|
|
extern int simpad_get_battery(struct simpad_battery* );
|
|
|
|
#endif // __ASM_ARCH_SIMPAD_H
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|