205 lines
7.9 KiB
Plaintext
205 lines
7.9 KiB
Plaintext
# Copyright (C) 2011, Marvell International Ltd.
|
|
#
|
|
# This software file (the "File") is distributed by Marvell International
|
|
# Ltd. under the terms of the GNU General Public License Version 2, June 1991
|
|
# (the "License"). You may use, redistribute and/or modify this File in
|
|
# accordance with the terms and conditions of the License, a copy of which
|
|
# is available by writing to the Free Software Foundation, Inc.,
|
|
# 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA or on the
|
|
# worldwide web at http://www.gnu.org/licenses/old-licenses/gpl-2.0.txt.
|
|
#
|
|
# THE FILE IS DISTRIBUTED AS-IS, WITHOUT WARRANTY OF ANY KIND, AND THE
|
|
# IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE
|
|
# ARE EXPRESSLY DISCLAIMED. The License provides additional details about
|
|
# this warranty disclaimer.
|
|
|
|
|
|
===============================================================================
|
|
U S E R M A N U A L
|
|
|
|
1) FOR DRIVER INSTALL
|
|
|
|
a) Copy sd8787.bin to /lib/firmware/mrvl/ directory,
|
|
create the directory if it doesn't exist.
|
|
b) Install WLAN driver,
|
|
insmod mwifiex.ko
|
|
c) Uninstall WLAN driver,
|
|
ifconfig mlanX down
|
|
rmmod mwifiex
|
|
|
|
|
|
2) FOR DRIVER CONFIGURATION AND INFO
|
|
The configurations can be done either using the 'iw' user space
|
|
utility or debugfs.
|
|
|
|
a) 'iw' utility commands
|
|
|
|
Following are some useful iw commands:-
|
|
|
|
iw dev mlan0 scan
|
|
|
|
This command will trigger a scan.
|
|
The command will then display the scan table entries
|
|
|
|
iw dev mlan0 connect -w <SSID> [<freq in MHz>] [<bssid>] [key 0:abcde d:1123456789a]
|
|
The above command can be used to connect to an AP with a particular SSID.
|
|
Ap's operating frequency can be specified or even the bssid. If the AP is using
|
|
WEP encryption, wep keys can be specified in the command.
|
|
Note: Every time before connecting to an AP scan command (iw dev mlan0 scan) should be used by user.
|
|
|
|
iw dev mlan0 disconnect
|
|
This command will be used to disconnect from an AP.
|
|
|
|
|
|
iw dev mlan0 ibss join <SSID> <freq in MHz> [fixed-freq] [fixed-bssid] [key 0:abcde]
|
|
The command will be used to join or create an ibss. Optionally, operating frequency,
|
|
bssid and the security related parameters can be specified while joining/creating
|
|
and ibss.
|
|
|
|
iw dev mlan0 ibss leave
|
|
The command will be used to leave an ibss network.
|
|
|
|
iw dev mlan0 link
|
|
The command will be used to get the connection status. The command will return parameters
|
|
such as SSID, operating frequency, rx/tx packets, signal strength, tx bitrate.
|
|
|
|
Apart from the iw utility all standard configurations using the 'iwconfig' utility are also supported.
|
|
|
|
b) Debugfs interface
|
|
|
|
The debugfs interface can be used for configurations and for getting
|
|
some useful information from the driver.
|
|
The section below explains the configurations that can be
|
|
done.
|
|
|
|
Mount debugfs to /debugfs mount point:
|
|
|
|
mkdir /debugfs
|
|
mount -t debugfs debugfs /debugfs
|
|
|
|
The information is provided in /debugfs/mwifiex/mlanX/:
|
|
|
|
iw reg set <country code>
|
|
The command will be used to change the regulatory domain.
|
|
|
|
iw reg get
|
|
The command will be used to get current regulatory domain.
|
|
|
|
info
|
|
This command is used to get driver info.
|
|
|
|
Usage:
|
|
cat info
|
|
|
|
driver_name = "mwifiex"
|
|
driver_version = <driver_name, driver_version, (firmware_version)>
|
|
interface_name = "mlanX"
|
|
bss_mode = "Ad-hoc" | "Managed" | "Auto" | "Unknown"
|
|
media_state = "Disconnected" | "Connected"
|
|
mac_address = <6-byte adapter MAC address>
|
|
multicase_count = <multicast address count>
|
|
essid = <current SSID>
|
|
bssid = <current BSSID>
|
|
channel = <current channel>
|
|
region_code = <current region code>
|
|
multicasr_address[n] = <multicast address>
|
|
num_tx_bytes = <number of bytes sent to device>
|
|
num_rx_bytes = <number of bytes received from device and sent to kernel>
|
|
num_tx_pkts = <number of packets sent to device>
|
|
num_rx_pkts = <number of packets received from device and sent to kernel>
|
|
num_tx_pkts_dropped = <number of Tx packets dropped by driver>
|
|
num_rx_pkts_dropped = <number of Rx packets dropped by driver>
|
|
num_tx_pkts_err = <number of Tx packets failed to send to device>
|
|
num_rx_pkts_err = <number of Rx packets failed to receive from device>
|
|
carrier "on" | "off"
|
|
tx queue "stopped" | "started"
|
|
|
|
The following debug info are provided in /debugfs/mwifiex/mlanX/debug:
|
|
|
|
int_counter = <interrupt count, cleared when interrupt handled>
|
|
wmm_ac_vo = <number of packets sent to device from WMM AcVo queue>
|
|
wmm_ac_vi = <number of packets sent to device from WMM AcVi queue>
|
|
wmm_ac_be = <number of packets sent to device from WMM AcBE queue>
|
|
wmm_ac_bk = <number of packets sent to device from WMM AcBK queue>
|
|
max_tx_buf_size = <maximum Tx buffer size>
|
|
tx_buf_size = <current Tx buffer size>
|
|
curr_tx_buf_size = <current Tx buffer size>
|
|
ps_mode = <0/1, CAM mode/PS mode>
|
|
ps_state = <0/1/2/3, full power state/awake state/pre-sleep state/sleep state>
|
|
is_deep_sleep = <0/1, not deep sleep state/deep sleep state>
|
|
wakeup_dev_req = <0/1, wakeup device not required/required>
|
|
wakeup_tries = <wakeup device count, cleared when device awake>
|
|
hs_configured = <0/1, host sleep not configured/configured>
|
|
hs_activated = <0/1, extended host sleep not activated/activated>
|
|
num_tx_timeout = <number of Tx timeout>
|
|
num_cmd_timeout = <number of timeout commands>
|
|
timeout_cmd_id = <command id of the last timeout command>
|
|
timeout_cmd_act = <command action of the last timeout command>
|
|
last_cmd_id = <command id of the last several commands sent to device>
|
|
last_cmd_act = <command action of the last several commands sent to device>
|
|
last_cmd_index = <0 based last command index>
|
|
last_cmd_resp_id = <command id of the last several command responses received from device>
|
|
last_cmd_resp_index = <0 based last command response index>
|
|
last_event = <event id of the last several events received from device>
|
|
last_event_index = <0 based last event index>
|
|
num_cmd_h2c_fail = <number of commands failed to send to device>
|
|
num_cmd_sleep_cfm_fail = <number of sleep confirm failed to send to device>
|
|
num_tx_h2c_fail = <number of data packets failed to send to device>
|
|
num_evt_deauth = <number of deauthenticated events received from device>
|
|
num_evt_disassoc = <number of disassociated events received from device>
|
|
num_evt_link_lost = <number of link lost events received from device>
|
|
num_cmd_deauth = <number of deauthenticate commands sent to device>
|
|
num_cmd_assoc_ok = <number of associate commands with success return>
|
|
num_cmd_assoc_fail = <number of associate commands with failure return>
|
|
cmd_sent = <0/1, send command resources available/sending command to device>
|
|
data_sent = <0/1, send data resources available/sending data to device>
|
|
mp_rd_bitmap = <SDIO multi-port read bitmap>
|
|
mp_wr_bitmap = <SDIO multi-port write bitmap>
|
|
cmd_resp_received = <0/1, no cmd response to process/response received and yet to process>
|
|
event_received = <0/1, no event to process/event received and yet to process>
|
|
ioctl_pending = <number of ioctl pending>
|
|
tx_pending = <number of Tx packet pending>
|
|
rx_pending = <number of Rx packet pending>
|
|
|
|
|
|
3) FOR DRIVER CONFIGURATION
|
|
|
|
regrdwr
|
|
This command is used to read/write the adapter register.
|
|
|
|
Usage:
|
|
echo " <type> <offset> [value]" > regrdwr
|
|
cat regrdwr
|
|
|
|
where the parameters are,
|
|
<type>: 1:MAC/SOC, 2:BBP, 3:RF, 4:PMIC, 5:CAU
|
|
<offset>: offset of register
|
|
[value]: value to be written
|
|
|
|
Examples:
|
|
echo "1 0xa060" > regrdwr : Read the MAC register
|
|
echo "1 0xa060 0x12" > regrdwr : Write the MAC register
|
|
echo "1 0xa794 0x80000000" > regrdwr
|
|
: Write 0x80000000 to MAC register
|
|
rdeeprom
|
|
This command is used to read the EEPROM contents of the card.
|
|
|
|
Usage:
|
|
echo "<offset> <length>" > rdeeprom
|
|
cat rdeeprom
|
|
|
|
where the parameters are,
|
|
<offset>: multiples of 4
|
|
<length>: 4-20, multiples of 4
|
|
|
|
Example:
|
|
echo "0 20" > rdeeprom : Read 20 bytes of EEPROM data from offset 0
|
|
|
|
getlog
|
|
This command is used to get the statistics available in the station.
|
|
Usage:
|
|
|
|
cat getlog
|
|
|
|
===============================================================================
|