1014 lines
25 KiB
C
1014 lines
25 KiB
C
/*
|
|
* Support for Sharp SL-Cxx00 Series of PDAs
|
|
* Models: SL-C3000 (Spitz), SL-C1000 (Akita) and SL-C3100 (Borzoi)
|
|
*
|
|
* Copyright (c) 2005 Richard Purdie
|
|
*
|
|
* Based on Sharp's 2.4 kernel patches/lubbock.c
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
* published by the Free Software Foundation.
|
|
*
|
|
*/
|
|
|
|
#include <linux/kernel.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/gpio_keys.h>
|
|
#include <linux/gpio.h>
|
|
#include <linux/leds.h>
|
|
#include <linux/i2c.h>
|
|
#include <linux/i2c/pxa-i2c.h>
|
|
#include <linux/i2c/pca953x.h>
|
|
#include <linux/spi/spi.h>
|
|
#include <linux/spi/ads7846.h>
|
|
#include <linux/spi/corgi_lcd.h>
|
|
#include <linux/spi/pxa2xx_spi.h>
|
|
#include <linux/mtd/sharpsl.h>
|
|
#include <linux/mtd/physmap.h>
|
|
#include <linux/input/matrix_keypad.h>
|
|
#include <linux/regulator/machine.h>
|
|
#include <linux/io.h>
|
|
|
|
#include <asm/setup.h>
|
|
#include <asm/mach-types.h>
|
|
#include <asm/mach/arch.h>
|
|
#include <asm/mach/sharpsl_param.h>
|
|
#include <asm/hardware/scoop.h>
|
|
|
|
#include <mach/pxa27x.h>
|
|
#include <mach/pxa27x-udc.h>
|
|
#include <mach/reset.h>
|
|
#include <mach/irda.h>
|
|
#include <mach/mmc.h>
|
|
#include <mach/ohci.h>
|
|
#include <mach/pxafb.h>
|
|
#include <mach/spitz.h>
|
|
#include <mach/sharpsl_pm.h>
|
|
#include <mach/smemc.h>
|
|
|
|
#include "generic.h"
|
|
#include "devices.h"
|
|
|
|
/******************************************************************************
|
|
* Pin configuration
|
|
******************************************************************************/
|
|
static unsigned long spitz_pin_config[] __initdata = {
|
|
/* Chip Selects */
|
|
GPIO78_nCS_2, /* SCOOP #2 */
|
|
GPIO79_nCS_3, /* NAND */
|
|
GPIO80_nCS_4, /* SCOOP #1 */
|
|
|
|
/* LCD - 16bpp Active TFT */
|
|
GPIOxx_LCD_TFT_16BPP,
|
|
|
|
/* PC Card */
|
|
GPIO48_nPOE,
|
|
GPIO49_nPWE,
|
|
GPIO50_nPIOR,
|
|
GPIO51_nPIOW,
|
|
GPIO85_nPCE_1,
|
|
GPIO54_nPCE_2,
|
|
GPIO55_nPREG,
|
|
GPIO56_nPWAIT,
|
|
GPIO57_nIOIS16,
|
|
GPIO104_PSKTSEL,
|
|
|
|
/* I2S */
|
|
GPIO28_I2S_BITCLK_OUT,
|
|
GPIO29_I2S_SDATA_IN,
|
|
GPIO30_I2S_SDATA_OUT,
|
|
GPIO31_I2S_SYNC,
|
|
|
|
/* MMC */
|
|
GPIO32_MMC_CLK,
|
|
GPIO112_MMC_CMD,
|
|
GPIO92_MMC_DAT_0,
|
|
GPIO109_MMC_DAT_1,
|
|
GPIO110_MMC_DAT_2,
|
|
GPIO111_MMC_DAT_3,
|
|
|
|
/* GPIOs */
|
|
GPIO9_GPIO, /* SPITZ_GPIO_nSD_DETECT */
|
|
GPIO16_GPIO, /* SPITZ_GPIO_SYNC */
|
|
GPIO81_GPIO, /* SPITZ_GPIO_nSD_WP */
|
|
GPIO41_GPIO, /* SPITZ_GPIO_USB_CONNECT */
|
|
GPIO37_GPIO, /* SPITZ_GPIO_USB_HOST */
|
|
GPIO35_GPIO, /* SPITZ_GPIO_USB_DEVICE */
|
|
GPIO22_GPIO, /* SPITZ_GPIO_HSYNC */
|
|
GPIO94_GPIO, /* SPITZ_GPIO_CF_CD */
|
|
GPIO105_GPIO, /* SPITZ_GPIO_CF_IRQ */
|
|
GPIO106_GPIO, /* SPITZ_GPIO_CF2_IRQ */
|
|
|
|
/* GPIO matrix keypad */
|
|
GPIO88_GPIO, /* column 0 */
|
|
GPIO23_GPIO, /* column 1 */
|
|
GPIO24_GPIO, /* column 2 */
|
|
GPIO25_GPIO, /* column 3 */
|
|
GPIO26_GPIO, /* column 4 */
|
|
GPIO27_GPIO, /* column 5 */
|
|
GPIO52_GPIO, /* column 6 */
|
|
GPIO103_GPIO, /* column 7 */
|
|
GPIO107_GPIO, /* column 8 */
|
|
GPIO108_GPIO, /* column 9 */
|
|
GPIO114_GPIO, /* column 10 */
|
|
GPIO12_GPIO, /* row 0 */
|
|
GPIO17_GPIO, /* row 1 */
|
|
GPIO91_GPIO, /* row 2 */
|
|
GPIO34_GPIO, /* row 3 */
|
|
GPIO36_GPIO, /* row 4 */
|
|
GPIO38_GPIO, /* row 5 */
|
|
GPIO39_GPIO, /* row 6 */
|
|
|
|
/* I2C */
|
|
GPIO117_I2C_SCL,
|
|
GPIO118_I2C_SDA,
|
|
|
|
GPIO0_GPIO | WAKEUP_ON_EDGE_RISE, /* SPITZ_GPIO_KEY_INT */
|
|
GPIO1_GPIO | WAKEUP_ON_EDGE_FALL, /* SPITZ_GPIO_RESET */
|
|
};
|
|
|
|
|
|
/******************************************************************************
|
|
* Scoop GPIO expander
|
|
******************************************************************************/
|
|
#if defined(CONFIG_SHARP_SCOOP) || defined(CONFIG_SHARP_SCOOP_MODULE)
|
|
/* SCOOP Device #1 */
|
|
static struct resource spitz_scoop_1_resources[] = {
|
|
[0] = {
|
|
.start = 0x10800000,
|
|
.end = 0x10800fff,
|
|
.flags = IORESOURCE_MEM,
|
|
},
|
|
};
|
|
|
|
static struct scoop_config spitz_scoop_1_setup = {
|
|
.io_dir = SPITZ_SCP_IO_DIR,
|
|
.io_out = SPITZ_SCP_IO_OUT,
|
|
.suspend_clr = SPITZ_SCP_SUS_CLR,
|
|
.suspend_set = SPITZ_SCP_SUS_SET,
|
|
.gpio_base = SPITZ_SCP_GPIO_BASE,
|
|
};
|
|
|
|
struct platform_device spitz_scoop_1_device = {
|
|
.name = "sharp-scoop",
|
|
.id = 0,
|
|
.dev = {
|
|
.platform_data = &spitz_scoop_1_setup,
|
|
},
|
|
.num_resources = ARRAY_SIZE(spitz_scoop_1_resources),
|
|
.resource = spitz_scoop_1_resources,
|
|
};
|
|
|
|
/* SCOOP Device #2 */
|
|
static struct resource spitz_scoop_2_resources[] = {
|
|
[0] = {
|
|
.start = 0x08800040,
|
|
.end = 0x08800fff,
|
|
.flags = IORESOURCE_MEM,
|
|
},
|
|
};
|
|
|
|
static struct scoop_config spitz_scoop_2_setup = {
|
|
.io_dir = SPITZ_SCP2_IO_DIR,
|
|
.io_out = SPITZ_SCP2_IO_OUT,
|
|
.suspend_clr = SPITZ_SCP2_SUS_CLR,
|
|
.suspend_set = SPITZ_SCP2_SUS_SET,
|
|
.gpio_base = SPITZ_SCP2_GPIO_BASE,
|
|
};
|
|
|
|
struct platform_device spitz_scoop_2_device = {
|
|
.name = "sharp-scoop",
|
|
.id = 1,
|
|
.dev = {
|
|
.platform_data = &spitz_scoop_2_setup,
|
|
},
|
|
.num_resources = ARRAY_SIZE(spitz_scoop_2_resources),
|
|
.resource = spitz_scoop_2_resources,
|
|
};
|
|
|
|
static void __init spitz_scoop_init(void)
|
|
{
|
|
platform_device_register(&spitz_scoop_1_device);
|
|
|
|
/* Akita doesn't have the second SCOOP chip */
|
|
if (!machine_is_akita())
|
|
platform_device_register(&spitz_scoop_2_device);
|
|
}
|
|
|
|
/* Power control is shared with between one of the CF slots and SD */
|
|
static void spitz_card_pwr_ctrl(uint8_t enable, uint8_t new_cpr)
|
|
{
|
|
unsigned short cpr;
|
|
unsigned long flags;
|
|
|
|
if (new_cpr & 0x7) {
|
|
gpio_set_value(SPITZ_GPIO_CF_POWER, 1);
|
|
mdelay(5);
|
|
}
|
|
|
|
local_irq_save(flags);
|
|
|
|
cpr = read_scoop_reg(&spitz_scoop_1_device.dev, SCOOP_CPR);
|
|
|
|
if (enable & new_cpr)
|
|
cpr |= new_cpr;
|
|
else
|
|
cpr &= ~enable;
|
|
|
|
write_scoop_reg(&spitz_scoop_1_device.dev, SCOOP_CPR, cpr);
|
|
|
|
local_irq_restore(flags);
|
|
|
|
if (!(cpr & 0x7)) {
|
|
mdelay(1);
|
|
gpio_set_value(SPITZ_GPIO_CF_POWER, 0);
|
|
}
|
|
}
|
|
|
|
#else
|
|
static inline void spitz_scoop_init(void) {}
|
|
static inline void spitz_card_pwr_ctrl(uint8_t enable, uint8_t new_cpr) {}
|
|
#endif
|
|
|
|
/******************************************************************************
|
|
* PCMCIA
|
|
******************************************************************************/
|
|
#if defined(CONFIG_PCMCIA_PXA2XX) || defined(CONFIG_PCMCIA_PXA2XX_MODULE)
|
|
static void spitz_pcmcia_pwr(struct device *scoop, uint16_t cpr, int nr)
|
|
{
|
|
/* Only need to override behaviour for slot 0 */
|
|
if (nr == 0)
|
|
spitz_card_pwr_ctrl(
|
|
cpr & (SCOOP_CPR_CF_3V | SCOOP_CPR_CF_XV), cpr);
|
|
else
|
|
write_scoop_reg(scoop, SCOOP_CPR, cpr);
|
|
}
|
|
|
|
static struct scoop_pcmcia_dev spitz_pcmcia_scoop[] = {
|
|
{
|
|
.dev = &spitz_scoop_1_device.dev,
|
|
.irq = SPITZ_IRQ_GPIO_CF_IRQ,
|
|
.cd_irq = SPITZ_IRQ_GPIO_CF_CD,
|
|
.cd_irq_str = "PCMCIA0 CD",
|
|
}, {
|
|
.dev = &spitz_scoop_2_device.dev,
|
|
.irq = SPITZ_IRQ_GPIO_CF2_IRQ,
|
|
.cd_irq = -1,
|
|
},
|
|
};
|
|
|
|
static struct scoop_pcmcia_config spitz_pcmcia_config = {
|
|
.devs = &spitz_pcmcia_scoop[0],
|
|
.num_devs = 2,
|
|
.power_ctrl = spitz_pcmcia_pwr,
|
|
};
|
|
|
|
static void __init spitz_pcmcia_init(void)
|
|
{
|
|
/* Akita has only one PCMCIA slot used */
|
|
if (machine_is_akita())
|
|
spitz_pcmcia_config.num_devs = 1;
|
|
|
|
platform_scoop_config = &spitz_pcmcia_config;
|
|
}
|
|
#else
|
|
static inline void spitz_pcmcia_init(void) {}
|
|
#endif
|
|
|
|
/******************************************************************************
|
|
* GPIO keyboard
|
|
******************************************************************************/
|
|
#if defined(CONFIG_KEYBOARD_MATRIX) || defined(CONFIG_KEYBOARD_MATRIX_MODULE)
|
|
|
|
#define SPITZ_KEY_CALENDAR KEY_F1
|
|
#define SPITZ_KEY_ADDRESS KEY_F2
|
|
#define SPITZ_KEY_FN KEY_F3
|
|
#define SPITZ_KEY_CANCEL KEY_F4
|
|
#define SPITZ_KEY_EXOK KEY_F5
|
|
#define SPITZ_KEY_EXCANCEL KEY_F6
|
|
#define SPITZ_KEY_EXJOGDOWN KEY_F7
|
|
#define SPITZ_KEY_EXJOGUP KEY_F8
|
|
#define SPITZ_KEY_JAP1 KEY_LEFTALT
|
|
#define SPITZ_KEY_JAP2 KEY_RIGHTCTRL
|
|
#define SPITZ_KEY_SYNC KEY_F9
|
|
#define SPITZ_KEY_MAIL KEY_F10
|
|
#define SPITZ_KEY_OK KEY_F11
|
|
#define SPITZ_KEY_MENU KEY_F12
|
|
|
|
static const uint32_t spitz_keymap[] = {
|
|
KEY(0, 0, KEY_LEFTCTRL),
|
|
KEY(0, 1, KEY_1),
|
|
KEY(0, 2, KEY_3),
|
|
KEY(0, 3, KEY_5),
|
|
KEY(0, 4, KEY_6),
|
|
KEY(0, 5, KEY_7),
|
|
KEY(0, 6, KEY_9),
|
|
KEY(0, 7, KEY_0),
|
|
KEY(0, 8, KEY_BACKSPACE),
|
|
KEY(0, 9, SPITZ_KEY_EXOK), /* EXOK */
|
|
KEY(0, 10, SPITZ_KEY_EXCANCEL), /* EXCANCEL */
|
|
KEY(1, 1, KEY_2),
|
|
KEY(1, 2, KEY_4),
|
|
KEY(1, 3, KEY_R),
|
|
KEY(1, 4, KEY_Y),
|
|
KEY(1, 5, KEY_8),
|
|
KEY(1, 6, KEY_I),
|
|
KEY(1, 7, KEY_O),
|
|
KEY(1, 8, KEY_P),
|
|
KEY(1, 9, SPITZ_KEY_EXJOGDOWN), /* EXJOGDOWN */
|
|
KEY(1, 10, SPITZ_KEY_EXJOGUP), /* EXJOGUP */
|
|
KEY(2, 0, KEY_TAB),
|
|
KEY(2, 1, KEY_Q),
|
|
KEY(2, 2, KEY_E),
|
|
KEY(2, 3, KEY_T),
|
|
KEY(2, 4, KEY_G),
|
|
KEY(2, 5, KEY_U),
|
|
KEY(2, 6, KEY_J),
|
|
KEY(2, 7, KEY_K),
|
|
KEY(3, 0, SPITZ_KEY_ADDRESS), /* ADDRESS */
|
|
KEY(3, 1, KEY_W),
|
|
KEY(3, 2, KEY_S),
|
|
KEY(3, 3, KEY_F),
|
|
KEY(3, 4, KEY_V),
|
|
KEY(3, 5, KEY_H),
|
|
KEY(3, 6, KEY_M),
|
|
KEY(3, 7, KEY_L),
|
|
KEY(3, 9, KEY_RIGHTSHIFT),
|
|
KEY(4, 0, SPITZ_KEY_CALENDAR), /* CALENDAR */
|
|
KEY(4, 1, KEY_A),
|
|
KEY(4, 2, KEY_D),
|
|
KEY(4, 3, KEY_C),
|
|
KEY(4, 4, KEY_B),
|
|
KEY(4, 5, KEY_N),
|
|
KEY(4, 6, KEY_DOT),
|
|
KEY(4, 8, KEY_ENTER),
|
|
KEY(4, 9, KEY_LEFTSHIFT),
|
|
KEY(5, 0, SPITZ_KEY_MAIL), /* MAIL */
|
|
KEY(5, 1, KEY_Z),
|
|
KEY(5, 2, KEY_X),
|
|
KEY(5, 3, KEY_MINUS),
|
|
KEY(5, 4, KEY_SPACE),
|
|
KEY(5, 5, KEY_COMMA),
|
|
KEY(5, 7, KEY_UP),
|
|
KEY(5, 10, SPITZ_KEY_FN), /* FN */
|
|
KEY(6, 0, KEY_SYSRQ),
|
|
KEY(6, 1, SPITZ_KEY_JAP1), /* JAP1 */
|
|
KEY(6, 2, SPITZ_KEY_JAP2), /* JAP2 */
|
|
KEY(6, 3, SPITZ_KEY_CANCEL), /* CANCEL */
|
|
KEY(6, 4, SPITZ_KEY_OK), /* OK */
|
|
KEY(6, 5, SPITZ_KEY_MENU), /* MENU */
|
|
KEY(6, 6, KEY_LEFT),
|
|
KEY(6, 7, KEY_DOWN),
|
|
KEY(6, 8, KEY_RIGHT),
|
|
};
|
|
|
|
static const struct matrix_keymap_data spitz_keymap_data = {
|
|
.keymap = spitz_keymap,
|
|
.keymap_size = ARRAY_SIZE(spitz_keymap),
|
|
};
|
|
|
|
static const uint32_t spitz_row_gpios[] =
|
|
{ 12, 17, 91, 34, 36, 38, 39 };
|
|
static const uint32_t spitz_col_gpios[] =
|
|
{ 88, 23, 24, 25, 26, 27, 52, 103, 107, 108, 114 };
|
|
|
|
static struct matrix_keypad_platform_data spitz_mkp_pdata = {
|
|
.keymap_data = &spitz_keymap_data,
|
|
.row_gpios = spitz_row_gpios,
|
|
.col_gpios = spitz_col_gpios,
|
|
.num_row_gpios = ARRAY_SIZE(spitz_row_gpios),
|
|
.num_col_gpios = ARRAY_SIZE(spitz_col_gpios),
|
|
.col_scan_delay_us = 10,
|
|
.debounce_ms = 10,
|
|
.wakeup = 1,
|
|
};
|
|
|
|
static struct platform_device spitz_mkp_device = {
|
|
.name = "matrix-keypad",
|
|
.id = -1,
|
|
.dev = {
|
|
.platform_data = &spitz_mkp_pdata,
|
|
},
|
|
};
|
|
|
|
static void __init spitz_mkp_init(void)
|
|
{
|
|
platform_device_register(&spitz_mkp_device);
|
|
}
|
|
#else
|
|
static inline void spitz_mkp_init(void) {}
|
|
#endif
|
|
|
|
/******************************************************************************
|
|
* GPIO keys
|
|
******************************************************************************/
|
|
#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
|
|
static struct gpio_keys_button spitz_gpio_keys[] = {
|
|
{
|
|
.type = EV_PWR,
|
|
.code = KEY_SUSPEND,
|
|
.gpio = SPITZ_GPIO_ON_KEY,
|
|
.desc = "On Off",
|
|
.wakeup = 1,
|
|
},
|
|
/* Two buttons detecting the lid state */
|
|
{
|
|
.type = EV_SW,
|
|
.code = 0,
|
|
.gpio = SPITZ_GPIO_SWA,
|
|
.desc = "Display Down",
|
|
},
|
|
{
|
|
.type = EV_SW,
|
|
.code = 1,
|
|
.gpio = SPITZ_GPIO_SWB,
|
|
.desc = "Lid Closed",
|
|
},
|
|
};
|
|
|
|
static struct gpio_keys_platform_data spitz_gpio_keys_platform_data = {
|
|
.buttons = spitz_gpio_keys,
|
|
.nbuttons = ARRAY_SIZE(spitz_gpio_keys),
|
|
};
|
|
|
|
static struct platform_device spitz_gpio_keys_device = {
|
|
.name = "gpio-keys",
|
|
.id = -1,
|
|
.dev = {
|
|
.platform_data = &spitz_gpio_keys_platform_data,
|
|
},
|
|
};
|
|
|
|
static void __init spitz_keys_init(void)
|
|
{
|
|
platform_device_register(&spitz_gpio_keys_device);
|
|
}
|
|
#else
|
|
static inline void spitz_keys_init(void) {}
|
|
#endif
|
|
|
|
/******************************************************************************
|
|
* LEDs
|
|
******************************************************************************/
|
|
#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
|
|
static struct gpio_led spitz_gpio_leds[] = {
|
|
{
|
|
.name = "spitz:amber:charge",
|
|
.default_trigger = "sharpsl-charge",
|
|
.gpio = SPITZ_GPIO_LED_ORANGE,
|
|
},
|
|
{
|
|
.name = "spitz:green:hddactivity",
|
|
.default_trigger = "ide-disk",
|
|
.gpio = SPITZ_GPIO_LED_GREEN,
|
|
},
|
|
};
|
|
|
|
static struct gpio_led_platform_data spitz_gpio_leds_info = {
|
|
.leds = spitz_gpio_leds,
|
|
.num_leds = ARRAY_SIZE(spitz_gpio_leds),
|
|
};
|
|
|
|
static struct platform_device spitz_led_device = {
|
|
.name = "leds-gpio",
|
|
.id = -1,
|
|
.dev = {
|
|
.platform_data = &spitz_gpio_leds_info,
|
|
},
|
|
};
|
|
|
|
static void __init spitz_leds_init(void)
|
|
{
|
|
platform_device_register(&spitz_led_device);
|
|
}
|
|
#else
|
|
static inline void spitz_leds_init(void) {}
|
|
#endif
|
|
|
|
/******************************************************************************
|
|
* SSP Devices
|
|
******************************************************************************/
|
|
#if defined(CONFIG_SPI_PXA2XX) || defined(CONFIG_SPI_PXA2XX_MODULE)
|
|
static void spitz_ads7846_wait_for_hsync(void)
|
|
{
|
|
while (gpio_get_value(SPITZ_GPIO_HSYNC))
|
|
cpu_relax();
|
|
|
|
while (!gpio_get_value(SPITZ_GPIO_HSYNC))
|
|
cpu_relax();
|
|
}
|
|
|
|
static struct ads7846_platform_data spitz_ads7846_info = {
|
|
.model = 7846,
|
|
.vref_delay_usecs = 100,
|
|
.x_plate_ohms = 419,
|
|
.y_plate_ohms = 486,
|
|
.pressure_max = 1024,
|
|
.gpio_pendown = SPITZ_GPIO_TP_INT,
|
|
.wait_for_sync = spitz_ads7846_wait_for_hsync,
|
|
};
|
|
|
|
static struct pxa2xx_spi_chip spitz_ads7846_chip = {
|
|
.gpio_cs = SPITZ_GPIO_ADS7846_CS,
|
|
};
|
|
|
|
static void spitz_bl_kick_battery(void)
|
|
{
|
|
void (*kick_batt)(void);
|
|
|
|
kick_batt = symbol_get(sharpsl_battery_kick);
|
|
if (kick_batt) {
|
|
kick_batt();
|
|
symbol_put(sharpsl_battery_kick);
|
|
}
|
|
}
|
|
|
|
static struct corgi_lcd_platform_data spitz_lcdcon_info = {
|
|
.init_mode = CORGI_LCD_MODE_VGA,
|
|
.max_intensity = 0x2f,
|
|
.default_intensity = 0x1f,
|
|
.limit_mask = 0x0b,
|
|
.gpio_backlight_cont = SPITZ_GPIO_BACKLIGHT_CONT,
|
|
.gpio_backlight_on = SPITZ_GPIO_BACKLIGHT_ON,
|
|
.kick_battery = spitz_bl_kick_battery,
|
|
};
|
|
|
|
static struct pxa2xx_spi_chip spitz_lcdcon_chip = {
|
|
.gpio_cs = SPITZ_GPIO_LCDCON_CS,
|
|
};
|
|
|
|
static struct pxa2xx_spi_chip spitz_max1111_chip = {
|
|
.gpio_cs = SPITZ_GPIO_MAX1111_CS,
|
|
};
|
|
|
|
static struct spi_board_info spitz_spi_devices[] = {
|
|
{
|
|
.modalias = "ads7846",
|
|
.max_speed_hz = 1200000,
|
|
.bus_num = 2,
|
|
.chip_select = 0,
|
|
.platform_data = &spitz_ads7846_info,
|
|
.controller_data = &spitz_ads7846_chip,
|
|
.irq = gpio_to_irq(SPITZ_GPIO_TP_INT),
|
|
}, {
|
|
.modalias = "corgi-lcd",
|
|
.max_speed_hz = 50000,
|
|
.bus_num = 2,
|
|
.chip_select = 1,
|
|
.platform_data = &spitz_lcdcon_info,
|
|
.controller_data = &spitz_lcdcon_chip,
|
|
}, {
|
|
.modalias = "max1111",
|
|
.max_speed_hz = 450000,
|
|
.bus_num = 2,
|
|
.chip_select = 2,
|
|
.controller_data = &spitz_max1111_chip,
|
|
},
|
|
};
|
|
|
|
static struct pxa2xx_spi_master spitz_spi_info = {
|
|
.num_chipselect = 3,
|
|
};
|
|
|
|
static void __init spitz_spi_init(void)
|
|
{
|
|
struct corgi_lcd_platform_data *lcd_data = &spitz_lcdcon_info;
|
|
|
|
if (machine_is_akita()) {
|
|
lcd_data->gpio_backlight_cont = AKITA_GPIO_BACKLIGHT_CONT;
|
|
lcd_data->gpio_backlight_on = AKITA_GPIO_BACKLIGHT_ON;
|
|
}
|
|
|
|
pxa2xx_set_spi_info(2, &spitz_spi_info);
|
|
spi_register_board_info(ARRAY_AND_SIZE(spitz_spi_devices));
|
|
}
|
|
#else
|
|
static inline void spitz_spi_init(void) {}
|
|
#endif
|
|
|
|
/******************************************************************************
|
|
* SD/MMC card controller
|
|
******************************************************************************/
|
|
#if defined(CONFIG_MMC_PXA) || defined(CONFIG_MMC_PXA_MODULE)
|
|
/*
|
|
* NOTE: The card detect interrupt isn't debounced so we delay it by 250ms to
|
|
* give the card a chance to fully insert/eject.
|
|
*/
|
|
static void spitz_mci_setpower(struct device *dev, unsigned int vdd)
|
|
{
|
|
struct pxamci_platform_data* p_d = dev->platform_data;
|
|
|
|
if ((1 << vdd) & p_d->ocr_mask)
|
|
spitz_card_pwr_ctrl(SCOOP_CPR_SD_3V, SCOOP_CPR_SD_3V);
|
|
else
|
|
spitz_card_pwr_ctrl(SCOOP_CPR_SD_3V, 0x0);
|
|
}
|
|
|
|
static struct pxamci_platform_data spitz_mci_platform_data = {
|
|
.detect_delay_ms = 250,
|
|
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
|
|
.setpower = spitz_mci_setpower,
|
|
.gpio_card_detect = SPITZ_GPIO_nSD_DETECT,
|
|
.gpio_card_ro = SPITZ_GPIO_nSD_WP,
|
|
.gpio_power = -1,
|
|
};
|
|
|
|
static void __init spitz_mmc_init(void)
|
|
{
|
|
pxa_set_mci_info(&spitz_mci_platform_data);
|
|
}
|
|
#else
|
|
static inline void spitz_mmc_init(void) {}
|
|
#endif
|
|
|
|
/******************************************************************************
|
|
* USB Host
|
|
******************************************************************************/
|
|
#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
|
|
static int spitz_ohci_init(struct device *dev)
|
|
{
|
|
int err;
|
|
|
|
err = gpio_request(SPITZ_GPIO_USB_HOST, "USB_HOST");
|
|
if (err)
|
|
return err;
|
|
|
|
/* Only Port 2 is connected, setup USB Port 2 Output Control Register */
|
|
UP2OCR = UP2OCR_HXS | UP2OCR_HXOE | UP2OCR_DPPDE | UP2OCR_DMPDE;
|
|
|
|
return gpio_direction_output(SPITZ_GPIO_USB_HOST, 1);
|
|
}
|
|
|
|
static void spitz_ohci_exit(struct device *dev)
|
|
{
|
|
gpio_free(SPITZ_GPIO_USB_HOST);
|
|
}
|
|
|
|
static struct pxaohci_platform_data spitz_ohci_platform_data = {
|
|
.port_mode = PMM_NPS_MODE,
|
|
.init = spitz_ohci_init,
|
|
.exit = spitz_ohci_exit,
|
|
.flags = ENABLE_PORT_ALL | NO_OC_PROTECTION,
|
|
.power_budget = 150,
|
|
};
|
|
|
|
static void __init spitz_uhc_init(void)
|
|
{
|
|
pxa_set_ohci_info(&spitz_ohci_platform_data);
|
|
}
|
|
#else
|
|
static inline void spitz_uhc_init(void) {}
|
|
#endif
|
|
|
|
/******************************************************************************
|
|
* IrDA
|
|
******************************************************************************/
|
|
#if defined(CONFIG_PXA_FICP) || defined(CONFIG_PXA_FICP_MODULE)
|
|
static struct pxaficp_platform_data spitz_ficp_platform_data = {
|
|
.transceiver_cap = IR_SIRMODE | IR_OFF,
|
|
};
|
|
|
|
static void __init spitz_irda_init(void)
|
|
{
|
|
if (machine_is_akita())
|
|
spitz_ficp_platform_data.gpio_pwdown = AKITA_GPIO_IR_ON;
|
|
else
|
|
spitz_ficp_platform_data.gpio_pwdown = SPITZ_GPIO_IR_ON;
|
|
|
|
pxa_set_ficp_info(&spitz_ficp_platform_data);
|
|
}
|
|
#else
|
|
static inline void spitz_irda_init(void) {}
|
|
#endif
|
|
|
|
/******************************************************************************
|
|
* Framebuffer
|
|
******************************************************************************/
|
|
#if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULE)
|
|
static struct pxafb_mode_info spitz_pxafb_modes[] = {
|
|
{
|
|
.pixclock = 19231,
|
|
.xres = 480,
|
|
.yres = 640,
|
|
.bpp = 16,
|
|
.hsync_len = 40,
|
|
.left_margin = 46,
|
|
.right_margin = 125,
|
|
.vsync_len = 3,
|
|
.upper_margin = 1,
|
|
.lower_margin = 0,
|
|
.sync = 0,
|
|
}, {
|
|
.pixclock = 134617,
|
|
.xres = 240,
|
|
.yres = 320,
|
|
.bpp = 16,
|
|
.hsync_len = 20,
|
|
.left_margin = 20,
|
|
.right_margin = 46,
|
|
.vsync_len = 2,
|
|
.upper_margin = 1,
|
|
.lower_margin = 0,
|
|
.sync = 0,
|
|
},
|
|
};
|
|
|
|
static struct pxafb_mach_info spitz_pxafb_info = {
|
|
.modes = spitz_pxafb_modes,
|
|
.num_modes = ARRAY_SIZE(spitz_pxafb_modes),
|
|
.fixed_modes = 1,
|
|
.lcd_conn = LCD_COLOR_TFT_16BPP | LCD_ALTERNATE_MAPPING,
|
|
};
|
|
|
|
static void __init spitz_lcd_init(void)
|
|
{
|
|
pxa_set_fb_info(NULL, &spitz_pxafb_info);
|
|
}
|
|
#else
|
|
static inline void spitz_lcd_init(void) {}
|
|
#endif
|
|
|
|
/******************************************************************************
|
|
* Framebuffer
|
|
******************************************************************************/
|
|
#if defined(CONFIG_MTD_NAND_SHARPSL) || defined(CONFIG_MTD_NAND_SHARPSL_MODULE)
|
|
static struct mtd_partition spitz_nand_partitions[] = {
|
|
{
|
|
.name = "System Area",
|
|
.offset = 0,
|
|
.size = 7 * 1024 * 1024,
|
|
}, {
|
|
.name = "Root Filesystem",
|
|
.offset = 7 * 1024 * 1024,
|
|
}, {
|
|
.name = "Home Filesystem",
|
|
.offset = MTDPART_OFS_APPEND,
|
|
.size = MTDPART_SIZ_FULL,
|
|
},
|
|
};
|
|
|
|
static uint8_t scan_ff_pattern[] = { 0xff, 0xff };
|
|
|
|
static struct nand_bbt_descr spitz_nand_bbt = {
|
|
.options = 0,
|
|
.offs = 4,
|
|
.len = 2,
|
|
.pattern = scan_ff_pattern
|
|
};
|
|
|
|
static struct nand_ecclayout akita_oobinfo = {
|
|
.oobfree = { {0x08, 0x09} },
|
|
.eccbytes = 24,
|
|
.eccpos = {
|
|
0x05, 0x01, 0x02, 0x03, 0x06, 0x07, 0x15, 0x11,
|
|
0x12, 0x13, 0x16, 0x17, 0x25, 0x21, 0x22, 0x23,
|
|
0x26, 0x27, 0x35, 0x31, 0x32, 0x33, 0x36, 0x37,
|
|
},
|
|
};
|
|
|
|
static struct sharpsl_nand_platform_data spitz_nand_pdata = {
|
|
.badblock_pattern = &spitz_nand_bbt,
|
|
.partitions = spitz_nand_partitions,
|
|
.nr_partitions = ARRAY_SIZE(spitz_nand_partitions),
|
|
};
|
|
|
|
static struct resource spitz_nand_resources[] = {
|
|
{
|
|
.start = PXA_CS3_PHYS,
|
|
.end = PXA_CS3_PHYS + SZ_4K - 1,
|
|
.flags = IORESOURCE_MEM,
|
|
},
|
|
};
|
|
|
|
static struct platform_device spitz_nand_device = {
|
|
.name = "sharpsl-nand",
|
|
.id = -1,
|
|
.resource = spitz_nand_resources,
|
|
.num_resources = ARRAY_SIZE(spitz_nand_resources),
|
|
.dev = {
|
|
.platform_data = &spitz_nand_pdata,
|
|
}
|
|
};
|
|
|
|
static void __init spitz_nand_init(void)
|
|
{
|
|
if (machine_is_spitz()) {
|
|
spitz_nand_partitions[1].size = 5 * 1024 * 1024;
|
|
} else if (machine_is_akita()) {
|
|
spitz_nand_partitions[1].size = 58 * 1024 * 1024;
|
|
spitz_nand_bbt.len = 1;
|
|
spitz_nand_pdata.ecc_layout = &akita_oobinfo;
|
|
} else if (machine_is_borzoi()) {
|
|
spitz_nand_partitions[1].size = 32 * 1024 * 1024;
|
|
spitz_nand_bbt.len = 1;
|
|
spitz_nand_pdata.ecc_layout = &akita_oobinfo;
|
|
}
|
|
|
|
platform_device_register(&spitz_nand_device);
|
|
}
|
|
#else
|
|
static inline void spitz_nand_init(void) {}
|
|
#endif
|
|
|
|
/******************************************************************************
|
|
* NOR Flash
|
|
******************************************************************************/
|
|
#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
|
|
static struct mtd_partition spitz_rom_parts[] = {
|
|
{
|
|
.name ="Boot PROM Filesystem",
|
|
.offset = 0x00140000,
|
|
.size = MTDPART_SIZ_FULL,
|
|
},
|
|
};
|
|
|
|
static struct physmap_flash_data spitz_rom_data = {
|
|
.width = 2,
|
|
.nr_parts = ARRAY_SIZE(spitz_rom_parts),
|
|
.parts = spitz_rom_parts,
|
|
};
|
|
|
|
static struct resource spitz_rom_resources[] = {
|
|
{
|
|
.start = PXA_CS0_PHYS,
|
|
.end = PXA_CS0_PHYS + SZ_8M - 1,
|
|
.flags = IORESOURCE_MEM,
|
|
},
|
|
};
|
|
|
|
static struct platform_device spitz_rom_device = {
|
|
.name = "physmap-flash",
|
|
.id = -1,
|
|
.resource = spitz_rom_resources,
|
|
.num_resources = ARRAY_SIZE(spitz_rom_resources),
|
|
.dev = {
|
|
.platform_data = &spitz_rom_data,
|
|
},
|
|
};
|
|
|
|
static void __init spitz_nor_init(void)
|
|
{
|
|
platform_device_register(&spitz_rom_device);
|
|
}
|
|
#else
|
|
static inline void spitz_nor_init(void) {}
|
|
#endif
|
|
|
|
/******************************************************************************
|
|
* GPIO expander
|
|
******************************************************************************/
|
|
#if defined(CONFIG_I2C_PXA) || defined(CONFIG_I2C_PXA_MODULE)
|
|
static struct pca953x_platform_data akita_pca953x_pdata = {
|
|
.gpio_base = AKITA_IOEXP_GPIO_BASE,
|
|
};
|
|
|
|
static struct i2c_board_info spitz_i2c_devs[] = {
|
|
{
|
|
.type = "wm8750",
|
|
.addr = 0x1b,
|
|
}, {
|
|
.type = "max7310",
|
|
.addr = 0x18,
|
|
.platform_data = &akita_pca953x_pdata,
|
|
},
|
|
};
|
|
|
|
static struct regulator_consumer_supply isl6271a_consumers[] = {
|
|
{
|
|
.supply = "vcc_core",
|
|
}
|
|
};
|
|
|
|
static struct regulator_init_data isl6271a_info[] = {
|
|
{
|
|
.constraints = {
|
|
.name = "vcc_core range",
|
|
.min_uV = 850000,
|
|
.max_uV = 1600000,
|
|
.always_on = 1,
|
|
.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
|
|
},
|
|
.consumer_supplies = isl6271a_consumers,
|
|
.num_consumer_supplies = ARRAY_SIZE(isl6271a_consumers),
|
|
}
|
|
};
|
|
|
|
static struct i2c_board_info spitz_pi2c_devs[] = {
|
|
{
|
|
.type = "isl6271a",
|
|
.addr = 0x0c,
|
|
.platform_data = &isl6271a_info,
|
|
},
|
|
};
|
|
|
|
static void __init spitz_i2c_init(void)
|
|
{
|
|
int size = ARRAY_SIZE(spitz_i2c_devs);
|
|
|
|
/* Only Akita has the max7310 chip */
|
|
if (!machine_is_akita())
|
|
size--;
|
|
|
|
pxa_set_i2c_info(NULL);
|
|
pxa27x_set_i2c_power_info(NULL);
|
|
i2c_register_board_info(0, spitz_i2c_devs, size);
|
|
i2c_register_board_info(1, ARRAY_AND_SIZE(spitz_pi2c_devs));
|
|
}
|
|
#else
|
|
static inline void spitz_i2c_init(void) {}
|
|
#endif
|
|
|
|
/******************************************************************************
|
|
* Machine init
|
|
******************************************************************************/
|
|
static void spitz_poweroff(void)
|
|
{
|
|
arm_machine_restart('g', NULL);
|
|
}
|
|
|
|
static void spitz_restart(char mode, const char *cmd)
|
|
{
|
|
uint32_t msc0 = __raw_readl(MSC0);
|
|
/* Bootloader magic for a reboot */
|
|
if ((msc0 & 0xffff0000) == 0x7ff00000)
|
|
__raw_writel((msc0 & 0xffff) | 0x7ee00000, MSC0);
|
|
|
|
spitz_poweroff();
|
|
}
|
|
|
|
static void __init spitz_init(void)
|
|
{
|
|
init_gpio_reset(SPITZ_GPIO_ON_RESET, 1, 0);
|
|
pm_power_off = spitz_poweroff;
|
|
arm_pm_restart = spitz_restart;
|
|
|
|
PMCR = 0x00;
|
|
|
|
/* Stop 3.6MHz and drive HIGH to PCMCIA and CS */
|
|
PCFR |= PCFR_OPDE;
|
|
|
|
pxa2xx_mfp_config(ARRAY_AND_SIZE(spitz_pin_config));
|
|
|
|
pxa_set_ffuart_info(NULL);
|
|
pxa_set_btuart_info(NULL);
|
|
pxa_set_stuart_info(NULL);
|
|
|
|
spitz_spi_init();
|
|
spitz_scoop_init();
|
|
spitz_mkp_init();
|
|
spitz_keys_init();
|
|
spitz_leds_init();
|
|
spitz_mmc_init();
|
|
spitz_pcmcia_init();
|
|
spitz_irda_init();
|
|
spitz_uhc_init();
|
|
spitz_lcd_init();
|
|
spitz_nor_init();
|
|
spitz_nand_init();
|
|
spitz_i2c_init();
|
|
}
|
|
|
|
static void __init spitz_fixup(struct machine_desc *desc,
|
|
struct tag *tags, char **cmdline, struct meminfo *mi)
|
|
{
|
|
sharpsl_save_param();
|
|
mi->nr_banks = 1;
|
|
mi->bank[0].start = 0xa0000000;
|
|
mi->bank[0].size = (64*1024*1024);
|
|
}
|
|
|
|
#ifdef CONFIG_MACH_SPITZ
|
|
MACHINE_START(SPITZ, "SHARP Spitz")
|
|
.fixup = spitz_fixup,
|
|
.map_io = pxa27x_map_io,
|
|
.init_irq = pxa27x_init_irq,
|
|
.handle_irq = pxa27x_handle_irq,
|
|
.init_machine = spitz_init,
|
|
.timer = &pxa_timer,
|
|
MACHINE_END
|
|
#endif
|
|
|
|
#ifdef CONFIG_MACH_BORZOI
|
|
MACHINE_START(BORZOI, "SHARP Borzoi")
|
|
.fixup = spitz_fixup,
|
|
.map_io = pxa27x_map_io,
|
|
.init_irq = pxa27x_init_irq,
|
|
.handle_irq = pxa27x_handle_irq,
|
|
.init_machine = spitz_init,
|
|
.timer = &pxa_timer,
|
|
MACHINE_END
|
|
#endif
|
|
|
|
#ifdef CONFIG_MACH_AKITA
|
|
MACHINE_START(AKITA, "SHARP Akita")
|
|
.fixup = spitz_fixup,
|
|
.map_io = pxa27x_map_io,
|
|
.init_irq = pxa27x_init_irq,
|
|
.handle_irq = pxa27x_handle_irq,
|
|
.init_machine = spitz_init,
|
|
.timer = &pxa_timer,
|
|
MACHINE_END
|
|
#endif
|