439 lines
12 KiB
C
439 lines
12 KiB
C
/*
|
|
* EHCI HCD (Host Controller Driver) PCI Bus Glue.
|
|
*
|
|
* Copyright (c) 2000-2004 by David Brownell
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify it
|
|
* under the terms of the GNU General Public License as published by the
|
|
* Free Software Foundation; either version 2 of the License, or (at your
|
|
* option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful, but
|
|
* WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
|
|
* or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
|
|
* for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software Foundation,
|
|
* Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
|
|
*/
|
|
|
|
#ifndef CONFIG_PCI
|
|
#error "This file is PCI bus glue. CONFIG_PCI must be defined."
|
|
#endif
|
|
|
|
/*-------------------------------------------------------------------------*/
|
|
|
|
/* called after powerup, by probe or system-pm "wakeup" */
|
|
static int ehci_pci_reinit(struct ehci_hcd *ehci, struct pci_dev *pdev)
|
|
{
|
|
u32 temp;
|
|
int retval;
|
|
|
|
/* optional debug port, normally in the first BAR */
|
|
temp = pci_find_capability(pdev, 0x0a);
|
|
if (temp) {
|
|
pci_read_config_dword(pdev, temp, &temp);
|
|
temp >>= 16;
|
|
if ((temp & (3 << 13)) == (1 << 13)) {
|
|
temp &= 0x1fff;
|
|
ehci->debug = ehci_to_hcd(ehci)->regs + temp;
|
|
temp = ehci_readl(ehci, &ehci->debug->control);
|
|
ehci_info(ehci, "debug port %d%s\n",
|
|
HCS_DEBUG_PORT(ehci->hcs_params),
|
|
(temp & DBGP_ENABLED)
|
|
? " IN USE"
|
|
: "");
|
|
if (!(temp & DBGP_ENABLED))
|
|
ehci->debug = NULL;
|
|
}
|
|
}
|
|
|
|
/* we expect static quirk code to handle the "extended capabilities"
|
|
* (currently just BIOS handoff) allowed starting with EHCI 0.96
|
|
*/
|
|
|
|
/* PCI Memory-Write-Invalidate cycle support is optional (uncommon) */
|
|
retval = pci_set_mwi(pdev);
|
|
if (!retval)
|
|
ehci_dbg(ehci, "MWI active\n");
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* called during probe() after chip reset completes */
|
|
static int ehci_pci_setup(struct usb_hcd *hcd)
|
|
{
|
|
struct ehci_hcd *ehci = hcd_to_ehci(hcd);
|
|
struct pci_dev *pdev = to_pci_dev(hcd->self.controller);
|
|
struct pci_dev *p_smbus;
|
|
u8 rev;
|
|
u32 temp;
|
|
int retval;
|
|
|
|
switch (pdev->vendor) {
|
|
case PCI_VENDOR_ID_TOSHIBA_2:
|
|
/* celleb's companion chip */
|
|
if (pdev->device == 0x01b5) {
|
|
#ifdef CONFIG_USB_EHCI_BIG_ENDIAN_MMIO
|
|
ehci->big_endian_mmio = 1;
|
|
#else
|
|
ehci_warn(ehci,
|
|
"unsupported big endian Toshiba quirk\n");
|
|
#endif
|
|
}
|
|
break;
|
|
}
|
|
|
|
ehci->caps = hcd->regs;
|
|
ehci->regs = hcd->regs +
|
|
HC_LENGTH(ehci_readl(ehci, &ehci->caps->hc_capbase));
|
|
|
|
dbg_hcs_params(ehci, "reset");
|
|
dbg_hcc_params(ehci, "reset");
|
|
|
|
/* ehci_init() causes memory for DMA transfers to be
|
|
* allocated. Thus, any vendor-specific workarounds based on
|
|
* limiting the type of memory used for DMA transfers must
|
|
* happen before ehci_init() is called. */
|
|
switch (pdev->vendor) {
|
|
case PCI_VENDOR_ID_NVIDIA:
|
|
/* NVidia reports that certain chips don't handle
|
|
* QH, ITD, or SITD addresses above 2GB. (But TD,
|
|
* data buffer, and periodic schedule are normal.)
|
|
*/
|
|
switch (pdev->device) {
|
|
case 0x003c: /* MCP04 */
|
|
case 0x005b: /* CK804 */
|
|
case 0x00d8: /* CK8 */
|
|
case 0x00e8: /* CK8S */
|
|
if (pci_set_consistent_dma_mask(pdev,
|
|
DMA_BIT_MASK(31)) < 0)
|
|
ehci_warn(ehci, "can't enable NVidia "
|
|
"workaround for >2GB RAM\n");
|
|
break;
|
|
}
|
|
break;
|
|
}
|
|
|
|
/* cache this readonly data; minimize chip reads */
|
|
ehci->hcs_params = ehci_readl(ehci, &ehci->caps->hcs_params);
|
|
|
|
retval = ehci_halt(ehci);
|
|
if (retval)
|
|
return retval;
|
|
|
|
/* data structure init */
|
|
retval = ehci_init(hcd);
|
|
if (retval)
|
|
return retval;
|
|
|
|
switch (pdev->vendor) {
|
|
case PCI_VENDOR_ID_TDI:
|
|
if (pdev->device == PCI_DEVICE_ID_TDI_EHCI) {
|
|
hcd->has_tt = 1;
|
|
tdi_reset(ehci);
|
|
}
|
|
break;
|
|
case PCI_VENDOR_ID_AMD:
|
|
/* AMD8111 EHCI doesn't work, according to AMD errata */
|
|
if (pdev->device == 0x7463) {
|
|
ehci_info(ehci, "ignoring AMD8111 (errata)\n");
|
|
retval = -EIO;
|
|
goto done;
|
|
}
|
|
break;
|
|
case PCI_VENDOR_ID_NVIDIA:
|
|
switch (pdev->device) {
|
|
/* Some NForce2 chips have problems with selective suspend;
|
|
* fixed in newer silicon.
|
|
*/
|
|
case 0x0068:
|
|
if (pdev->revision < 0xa4)
|
|
ehci->no_selective_suspend = 1;
|
|
break;
|
|
}
|
|
break;
|
|
case PCI_VENDOR_ID_VIA:
|
|
if (pdev->device == 0x3104 && (pdev->revision & 0xf0) == 0x60) {
|
|
u8 tmp;
|
|
|
|
/* The VT6212 defaults to a 1 usec EHCI sleep time which
|
|
* hogs the PCI bus *badly*. Setting bit 5 of 0x4B makes
|
|
* that sleep time use the conventional 10 usec.
|
|
*/
|
|
pci_read_config_byte(pdev, 0x4b, &tmp);
|
|
if (tmp & 0x20)
|
|
break;
|
|
pci_write_config_byte(pdev, 0x4b, tmp | 0x20);
|
|
}
|
|
break;
|
|
case PCI_VENDOR_ID_ATI:
|
|
/* SB600 and old version of SB700 have a bug in EHCI controller,
|
|
* which causes usb devices lose response in some cases.
|
|
*/
|
|
if ((pdev->device == 0x4386) || (pdev->device == 0x4396)) {
|
|
p_smbus = pci_get_device(PCI_VENDOR_ID_ATI,
|
|
PCI_DEVICE_ID_ATI_SBX00_SMBUS,
|
|
NULL);
|
|
if (!p_smbus)
|
|
break;
|
|
rev = p_smbus->revision;
|
|
if ((pdev->device == 0x4386) || (rev == 0x3a)
|
|
|| (rev == 0x3b)) {
|
|
u8 tmp;
|
|
ehci_info(ehci, "applying AMD SB600/SB700 USB "
|
|
"freeze workaround\n");
|
|
pci_read_config_byte(pdev, 0x53, &tmp);
|
|
pci_write_config_byte(pdev, 0x53, tmp | (1<<3));
|
|
}
|
|
pci_dev_put(p_smbus);
|
|
}
|
|
break;
|
|
}
|
|
|
|
ehci_reset(ehci);
|
|
|
|
/* at least the Genesys GL880S needs fixup here */
|
|
temp = HCS_N_CC(ehci->hcs_params) * HCS_N_PCC(ehci->hcs_params);
|
|
temp &= 0x0f;
|
|
if (temp && HCS_N_PORTS(ehci->hcs_params) > temp) {
|
|
ehci_dbg(ehci, "bogus port configuration: "
|
|
"cc=%d x pcc=%d < ports=%d\n",
|
|
HCS_N_CC(ehci->hcs_params),
|
|
HCS_N_PCC(ehci->hcs_params),
|
|
HCS_N_PORTS(ehci->hcs_params));
|
|
|
|
switch (pdev->vendor) {
|
|
case 0x17a0: /* GENESYS */
|
|
/* GL880S: should be PORTS=2 */
|
|
temp |= (ehci->hcs_params & ~0xf);
|
|
ehci->hcs_params = temp;
|
|
break;
|
|
case PCI_VENDOR_ID_NVIDIA:
|
|
/* NF4: should be PCC=10 */
|
|
break;
|
|
}
|
|
}
|
|
|
|
/* Serial Bus Release Number is at PCI 0x60 offset */
|
|
pci_read_config_byte(pdev, 0x60, &ehci->sbrn);
|
|
|
|
/* Keep this around for a while just in case some EHCI
|
|
* implementation uses legacy PCI PM support. This test
|
|
* can be removed on 17 Dec 2009 if the dev_warn() hasn't
|
|
* been triggered by then.
|
|
*/
|
|
if (!device_can_wakeup(&pdev->dev)) {
|
|
u16 port_wake;
|
|
|
|
pci_read_config_word(pdev, 0x62, &port_wake);
|
|
if (port_wake & 0x0001) {
|
|
dev_warn(&pdev->dev, "Enabling legacy PCI PM\n");
|
|
device_set_wakeup_capable(&pdev->dev, 1);
|
|
}
|
|
}
|
|
|
|
#ifdef CONFIG_USB_SUSPEND
|
|
/* REVISIT: the controller works fine for wakeup iff the root hub
|
|
* itself is "globally" suspended, but usbcore currently doesn't
|
|
* understand such things.
|
|
*
|
|
* System suspend currently expects to be able to suspend the entire
|
|
* device tree, device-at-a-time. If we failed selective suspend
|
|
* reports, system suspend would fail; so the root hub code must claim
|
|
* success. That's lying to usbcore, and it matters for for runtime
|
|
* PM scenarios with selective suspend and remote wakeup...
|
|
*/
|
|
if (ehci->no_selective_suspend && device_can_wakeup(&pdev->dev))
|
|
ehci_warn(ehci, "selective suspend/wakeup unavailable\n");
|
|
#endif
|
|
|
|
ehci_port_power(ehci, 1);
|
|
retval = ehci_pci_reinit(ehci, pdev);
|
|
done:
|
|
return retval;
|
|
}
|
|
|
|
/*-------------------------------------------------------------------------*/
|
|
|
|
#ifdef CONFIG_PM
|
|
|
|
/* suspend/resume, section 4.3 */
|
|
|
|
/* These routines rely on the PCI bus glue
|
|
* to handle powerdown and wakeup, and currently also on
|
|
* transceivers that don't need any software attention to set up
|
|
* the right sort of wakeup.
|
|
* Also they depend on separate root hub suspend/resume.
|
|
*/
|
|
|
|
static int ehci_pci_suspend(struct usb_hcd *hcd, pm_message_t message)
|
|
{
|
|
struct ehci_hcd *ehci = hcd_to_ehci(hcd);
|
|
unsigned long flags;
|
|
int rc = 0;
|
|
|
|
if (time_before(jiffies, ehci->next_statechange))
|
|
msleep(10);
|
|
|
|
/* Root hub was already suspended. Disable irq emission and
|
|
* mark HW unaccessible, bail out if RH has been resumed. Use
|
|
* the spinlock to properly synchronize with possible pending
|
|
* RH suspend or resume activity.
|
|
*
|
|
* This is still racy as hcd->state is manipulated outside of
|
|
* any locks =P But that will be a different fix.
|
|
*/
|
|
spin_lock_irqsave (&ehci->lock, flags);
|
|
if (hcd->state != HC_STATE_SUSPENDED) {
|
|
rc = -EINVAL;
|
|
goto bail;
|
|
}
|
|
ehci_writel(ehci, 0, &ehci->regs->intr_enable);
|
|
(void)ehci_readl(ehci, &ehci->regs->intr_enable);
|
|
|
|
/* make sure snapshot being resumed re-enumerates everything */
|
|
if (message.event == PM_EVENT_PRETHAW) {
|
|
ehci_halt(ehci);
|
|
ehci_reset(ehci);
|
|
}
|
|
|
|
clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
|
|
bail:
|
|
spin_unlock_irqrestore (&ehci->lock, flags);
|
|
|
|
// could save FLADJ in case of Vaux power loss
|
|
// ... we'd only use it to handle clock skew
|
|
|
|
return rc;
|
|
}
|
|
|
|
static int ehci_pci_resume(struct usb_hcd *hcd)
|
|
{
|
|
struct ehci_hcd *ehci = hcd_to_ehci(hcd);
|
|
struct pci_dev *pdev = to_pci_dev(hcd->self.controller);
|
|
|
|
// maybe restore FLADJ
|
|
|
|
if (time_before(jiffies, ehci->next_statechange))
|
|
msleep(100);
|
|
|
|
/* Mark hardware accessible again as we are out of D3 state by now */
|
|
set_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
|
|
|
|
/* If CF is still set, we maintained PCI Vaux power.
|
|
* Just undo the effect of ehci_pci_suspend().
|
|
*/
|
|
if (ehci_readl(ehci, &ehci->regs->configured_flag) == FLAG_CF) {
|
|
int mask = INTR_MASK;
|
|
|
|
if (!hcd->self.root_hub->do_remote_wakeup)
|
|
mask &= ~STS_PCD;
|
|
ehci_writel(ehci, mask, &ehci->regs->intr_enable);
|
|
ehci_readl(ehci, &ehci->regs->intr_enable);
|
|
return 0;
|
|
}
|
|
|
|
ehci_dbg(ehci, "lost power, restarting\n");
|
|
usb_root_hub_lost_power(hcd->self.root_hub);
|
|
|
|
/* Else reset, to cope with power loss or flush-to-storage
|
|
* style "resume" having let BIOS kick in during reboot.
|
|
*/
|
|
(void) ehci_halt(ehci);
|
|
(void) ehci_reset(ehci);
|
|
(void) ehci_pci_reinit(ehci, pdev);
|
|
|
|
/* emptying the schedule aborts any urbs */
|
|
spin_lock_irq(&ehci->lock);
|
|
if (ehci->reclaim)
|
|
end_unlink_async(ehci);
|
|
ehci_work(ehci);
|
|
spin_unlock_irq(&ehci->lock);
|
|
|
|
ehci_writel(ehci, ehci->command, &ehci->regs->command);
|
|
ehci_writel(ehci, FLAG_CF, &ehci->regs->configured_flag);
|
|
ehci_readl(ehci, &ehci->regs->command); /* unblock posted writes */
|
|
|
|
/* here we "know" root ports should always stay powered */
|
|
ehci_port_power(ehci, 1);
|
|
|
|
hcd->state = HC_STATE_SUSPENDED;
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
static const struct hc_driver ehci_pci_hc_driver = {
|
|
.description = hcd_name,
|
|
.product_desc = "EHCI Host Controller",
|
|
.hcd_priv_size = sizeof(struct ehci_hcd),
|
|
|
|
/*
|
|
* generic hardware linkage
|
|
*/
|
|
.irq = ehci_irq,
|
|
.flags = HCD_MEMORY | HCD_USB2,
|
|
|
|
/*
|
|
* basic lifecycle operations
|
|
*/
|
|
.reset = ehci_pci_setup,
|
|
.start = ehci_run,
|
|
#ifdef CONFIG_PM
|
|
.pci_suspend = ehci_pci_suspend,
|
|
.pci_resume = ehci_pci_resume,
|
|
#endif
|
|
.stop = ehci_stop,
|
|
.shutdown = ehci_shutdown,
|
|
|
|
/*
|
|
* managing i/o requests and associated device resources
|
|
*/
|
|
.urb_enqueue = ehci_urb_enqueue,
|
|
.urb_dequeue = ehci_urb_dequeue,
|
|
.endpoint_disable = ehci_endpoint_disable,
|
|
|
|
/*
|
|
* scheduling support
|
|
*/
|
|
.get_frame_number = ehci_get_frame,
|
|
|
|
/*
|
|
* root hub support
|
|
*/
|
|
.hub_status_data = ehci_hub_status_data,
|
|
.hub_control = ehci_hub_control,
|
|
.bus_suspend = ehci_bus_suspend,
|
|
.bus_resume = ehci_bus_resume,
|
|
.relinquish_port = ehci_relinquish_port,
|
|
.port_handed_over = ehci_port_handed_over,
|
|
};
|
|
|
|
/*-------------------------------------------------------------------------*/
|
|
|
|
/* PCI driver selection metadata; PCI hotplugging uses this */
|
|
static const struct pci_device_id pci_ids [] = { {
|
|
/* handle any USB 2.0 EHCI controller */
|
|
PCI_DEVICE_CLASS(PCI_CLASS_SERIAL_USB_EHCI, ~0),
|
|
.driver_data = (unsigned long) &ehci_pci_hc_driver,
|
|
},
|
|
{ /* end: all zeroes */ }
|
|
};
|
|
MODULE_DEVICE_TABLE(pci, pci_ids);
|
|
|
|
/* pci driver glue; this is a "new style" PCI driver module */
|
|
static struct pci_driver ehci_pci_driver = {
|
|
.name = (char *) hcd_name,
|
|
.id_table = pci_ids,
|
|
|
|
.probe = usb_hcd_pci_probe,
|
|
.remove = usb_hcd_pci_remove,
|
|
|
|
#ifdef CONFIG_PM
|
|
.suspend = usb_hcd_pci_suspend,
|
|
.resume = usb_hcd_pci_resume,
|
|
#endif
|
|
.shutdown = usb_hcd_pci_shutdown,
|
|
};
|