484 lines
12 KiB
C
484 lines
12 KiB
C
/*
|
|
* linux/arch/arm/mach-omap2/mmc-twl4030.c
|
|
*
|
|
* Copyright (C) 2007-2008 Texas Instruments
|
|
* Copyright (C) 2008 Nokia Corporation
|
|
* Author: Texas Instruments
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
* published by the Free Software Foundation.
|
|
*/
|
|
#include <linux/err.h>
|
|
#include <linux/io.h>
|
|
#include <linux/module.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/gpio.h>
|
|
#include <linux/i2c/twl4030.h>
|
|
#include <linux/regulator/machine.h>
|
|
|
|
#include <mach/hardware.h>
|
|
#include <mach/control.h>
|
|
#include <mach/mmc.h>
|
|
#include <mach/board.h>
|
|
|
|
#include "mmc-twl4030.h"
|
|
|
|
#if defined(CONFIG_TWL4030_CORE) && \
|
|
(defined(CONFIG_MMC_OMAP_HS) || defined(CONFIG_MMC_OMAP_HS_MODULE))
|
|
|
|
#define LDO_CLR 0x00
|
|
#define VSEL_S2_CLR 0x40
|
|
|
|
#define VMMC1_DEV_GRP 0x27
|
|
#define VMMC1_CLR 0x00
|
|
#define VMMC1_315V 0x03
|
|
#define VMMC1_300V 0x02
|
|
#define VMMC1_285V 0x01
|
|
#define VMMC1_185V 0x00
|
|
#define VMMC1_DEDICATED 0x2A
|
|
|
|
#define VMMC2_DEV_GRP 0x2B
|
|
#define VMMC2_CLR 0x40
|
|
#define VMMC2_315V 0x0c
|
|
#define VMMC2_300V 0x0b
|
|
#define VMMC2_285V 0x0a
|
|
#define VMMC2_280V 0x09
|
|
#define VMMC2_260V 0x08
|
|
#define VMMC2_185V 0x06
|
|
#define VMMC2_DEDICATED 0x2E
|
|
|
|
#define VMMC_DEV_GRP_P1 0x20
|
|
|
|
static u16 control_pbias_offset;
|
|
static u16 control_devconf1_offset;
|
|
|
|
#define HSMMC_NAME_LEN 9
|
|
|
|
static struct twl_mmc_controller {
|
|
struct omap_mmc_platform_data *mmc;
|
|
u8 twl_vmmc_dev_grp;
|
|
u8 twl_mmc_dedicated;
|
|
char name[HSMMC_NAME_LEN + 1];
|
|
} hsmmc[OMAP34XX_NR_MMC] = {
|
|
{
|
|
.twl_vmmc_dev_grp = VMMC1_DEV_GRP,
|
|
.twl_mmc_dedicated = VMMC1_DEDICATED,
|
|
},
|
|
{
|
|
.twl_vmmc_dev_grp = VMMC2_DEV_GRP,
|
|
.twl_mmc_dedicated = VMMC2_DEDICATED,
|
|
},
|
|
};
|
|
|
|
static int twl_mmc_card_detect(int irq)
|
|
{
|
|
unsigned i;
|
|
|
|
for (i = 0; i < ARRAY_SIZE(hsmmc); i++) {
|
|
struct omap_mmc_platform_data *mmc;
|
|
|
|
mmc = hsmmc[i].mmc;
|
|
if (!mmc)
|
|
continue;
|
|
if (irq != mmc->slots[0].card_detect_irq)
|
|
continue;
|
|
|
|
/* NOTE: assumes card detect signal is active-low */
|
|
return !gpio_get_value_cansleep(mmc->slots[0].switch_pin);
|
|
}
|
|
return -ENOSYS;
|
|
}
|
|
|
|
static int twl_mmc_get_ro(struct device *dev, int slot)
|
|
{
|
|
struct omap_mmc_platform_data *mmc = dev->platform_data;
|
|
|
|
/* NOTE: assumes write protect signal is active-high */
|
|
return gpio_get_value_cansleep(mmc->slots[0].gpio_wp);
|
|
}
|
|
|
|
static int twl_mmc_get_cover_state(struct device *dev, int slot)
|
|
{
|
|
struct omap_mmc_platform_data *mmc = dev->platform_data;
|
|
|
|
/* NOTE: assumes card detect signal is active-low */
|
|
return !gpio_get_value_cansleep(mmc->slots[0].switch_pin);
|
|
}
|
|
|
|
/*
|
|
* MMC Slot Initialization.
|
|
*/
|
|
static int twl_mmc_late_init(struct device *dev)
|
|
{
|
|
struct omap_mmc_platform_data *mmc = dev->platform_data;
|
|
int ret = 0;
|
|
int i;
|
|
|
|
ret = gpio_request(mmc->slots[0].switch_pin, "mmc_cd");
|
|
if (ret)
|
|
goto done;
|
|
ret = gpio_direction_input(mmc->slots[0].switch_pin);
|
|
if (ret)
|
|
goto err;
|
|
|
|
for (i = 0; i < ARRAY_SIZE(hsmmc); i++) {
|
|
if (hsmmc[i].name == mmc->slots[0].name) {
|
|
hsmmc[i].mmc = mmc;
|
|
break;
|
|
}
|
|
}
|
|
|
|
return 0;
|
|
|
|
err:
|
|
gpio_free(mmc->slots[0].switch_pin);
|
|
done:
|
|
mmc->slots[0].card_detect_irq = 0;
|
|
mmc->slots[0].card_detect = NULL;
|
|
|
|
dev_err(dev, "err %d configuring card detect\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
static void twl_mmc_cleanup(struct device *dev)
|
|
{
|
|
struct omap_mmc_platform_data *mmc = dev->platform_data;
|
|
|
|
gpio_free(mmc->slots[0].switch_pin);
|
|
}
|
|
|
|
#ifdef CONFIG_PM
|
|
|
|
static int twl_mmc_suspend(struct device *dev, int slot)
|
|
{
|
|
struct omap_mmc_platform_data *mmc = dev->platform_data;
|
|
|
|
disable_irq(mmc->slots[0].card_detect_irq);
|
|
return 0;
|
|
}
|
|
|
|
static int twl_mmc_resume(struct device *dev, int slot)
|
|
{
|
|
struct omap_mmc_platform_data *mmc = dev->platform_data;
|
|
|
|
enable_irq(mmc->slots[0].card_detect_irq);
|
|
return 0;
|
|
}
|
|
|
|
#else
|
|
#define twl_mmc_suspend NULL
|
|
#define twl_mmc_resume NULL
|
|
#endif
|
|
|
|
/*
|
|
* Sets the MMC voltage in twl4030
|
|
*/
|
|
|
|
#define MMC1_OCR (MMC_VDD_165_195 \
|
|
|MMC_VDD_28_29|MMC_VDD_29_30|MMC_VDD_30_31|MMC_VDD_31_32)
|
|
#define MMC2_OCR (MMC_VDD_165_195 \
|
|
|MMC_VDD_25_26|MMC_VDD_26_27|MMC_VDD_27_28 \
|
|
|MMC_VDD_28_29|MMC_VDD_29_30|MMC_VDD_30_31|MMC_VDD_31_32)
|
|
|
|
static int twl_mmc_set_voltage(struct twl_mmc_controller *c, int vdd)
|
|
{
|
|
int ret;
|
|
u8 vmmc = 0, dev_grp_val;
|
|
|
|
if (!vdd)
|
|
goto doit;
|
|
|
|
if (c->twl_vmmc_dev_grp == VMMC1_DEV_GRP) {
|
|
/* VMMC1: max 220 mA. And for 8-bit mode,
|
|
* VSIM: max 50 mA
|
|
*/
|
|
switch (1 << vdd) {
|
|
case MMC_VDD_165_195:
|
|
vmmc = VMMC1_185V;
|
|
/* and VSIM_180V */
|
|
break;
|
|
case MMC_VDD_28_29:
|
|
vmmc = VMMC1_285V;
|
|
/* and VSIM_280V */
|
|
break;
|
|
case MMC_VDD_29_30:
|
|
case MMC_VDD_30_31:
|
|
vmmc = VMMC1_300V;
|
|
/* and VSIM_300V */
|
|
break;
|
|
case MMC_VDD_31_32:
|
|
vmmc = VMMC1_315V;
|
|
/* error if VSIM needed */
|
|
break;
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
} else if (c->twl_vmmc_dev_grp == VMMC2_DEV_GRP) {
|
|
/* VMMC2: max 100 mA */
|
|
switch (1 << vdd) {
|
|
case MMC_VDD_165_195:
|
|
vmmc = VMMC2_185V;
|
|
break;
|
|
case MMC_VDD_25_26:
|
|
case MMC_VDD_26_27:
|
|
vmmc = VMMC2_260V;
|
|
break;
|
|
case MMC_VDD_27_28:
|
|
vmmc = VMMC2_280V;
|
|
break;
|
|
case MMC_VDD_28_29:
|
|
vmmc = VMMC2_285V;
|
|
break;
|
|
case MMC_VDD_29_30:
|
|
case MMC_VDD_30_31:
|
|
vmmc = VMMC2_300V;
|
|
break;
|
|
case MMC_VDD_31_32:
|
|
vmmc = VMMC2_315V;
|
|
break;
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
} else {
|
|
return -EINVAL;
|
|
}
|
|
|
|
doit:
|
|
if (vdd)
|
|
dev_grp_val = VMMC_DEV_GRP_P1; /* Power up */
|
|
else
|
|
dev_grp_val = LDO_CLR; /* Power down */
|
|
|
|
ret = twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER,
|
|
dev_grp_val, c->twl_vmmc_dev_grp);
|
|
if (ret || !vdd)
|
|
return ret;
|
|
|
|
ret = twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER,
|
|
vmmc, c->twl_mmc_dedicated);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int twl_mmc1_set_power(struct device *dev, int slot, int power_on,
|
|
int vdd)
|
|
{
|
|
u32 reg;
|
|
int ret = 0;
|
|
struct twl_mmc_controller *c = &hsmmc[0];
|
|
struct omap_mmc_platform_data *mmc = dev->platform_data;
|
|
|
|
/*
|
|
* Assume we power both OMAP VMMC1 (for CMD, CLK, DAT0..3) and the
|
|
* card using the same TWL VMMC1 supply (hsmmc[0]); OMAP has both
|
|
* 1.8V and 3.0V modes, controlled by the PBIAS register.
|
|
*
|
|
* In 8-bit modes, OMAP VMMC1A (for DAT4..7) needs a supply, which
|
|
* is most naturally TWL VSIM; those pins also use PBIAS.
|
|
*/
|
|
if (power_on) {
|
|
if (cpu_is_omap2430()) {
|
|
reg = omap_ctrl_readl(OMAP243X_CONTROL_DEVCONF1);
|
|
if ((1 << vdd) >= MMC_VDD_30_31)
|
|
reg |= OMAP243X_MMC1_ACTIVE_OVERWRITE;
|
|
else
|
|
reg &= ~OMAP243X_MMC1_ACTIVE_OVERWRITE;
|
|
omap_ctrl_writel(reg, OMAP243X_CONTROL_DEVCONF1);
|
|
}
|
|
|
|
if (mmc->slots[0].internal_clock) {
|
|
reg = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
|
|
reg |= OMAP2_MMCSDIO1ADPCLKISEL;
|
|
omap_ctrl_writel(reg, OMAP2_CONTROL_DEVCONF0);
|
|
}
|
|
|
|
reg = omap_ctrl_readl(control_pbias_offset);
|
|
reg |= OMAP2_PBIASSPEEDCTRL0;
|
|
reg &= ~OMAP2_PBIASLITEPWRDNZ0;
|
|
omap_ctrl_writel(reg, control_pbias_offset);
|
|
|
|
ret = twl_mmc_set_voltage(c, vdd);
|
|
|
|
/* 100ms delay required for PBIAS configuration */
|
|
msleep(100);
|
|
reg = omap_ctrl_readl(control_pbias_offset);
|
|
reg |= (OMAP2_PBIASLITEPWRDNZ0 | OMAP2_PBIASSPEEDCTRL0);
|
|
if ((1 << vdd) <= MMC_VDD_165_195)
|
|
reg &= ~OMAP2_PBIASLITEVMODE0;
|
|
else
|
|
reg |= OMAP2_PBIASLITEVMODE0;
|
|
omap_ctrl_writel(reg, control_pbias_offset);
|
|
} else {
|
|
reg = omap_ctrl_readl(control_pbias_offset);
|
|
reg &= ~OMAP2_PBIASLITEPWRDNZ0;
|
|
omap_ctrl_writel(reg, control_pbias_offset);
|
|
|
|
ret = twl_mmc_set_voltage(c, 0);
|
|
|
|
/* 100ms delay required for PBIAS configuration */
|
|
msleep(100);
|
|
reg = omap_ctrl_readl(control_pbias_offset);
|
|
reg |= (OMAP2_PBIASSPEEDCTRL0 | OMAP2_PBIASLITEPWRDNZ0 |
|
|
OMAP2_PBIASLITEVMODE0);
|
|
omap_ctrl_writel(reg, control_pbias_offset);
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int twl_mmc2_set_power(struct device *dev, int slot, int power_on, int vdd)
|
|
{
|
|
int ret;
|
|
struct twl_mmc_controller *c = &hsmmc[1];
|
|
struct omap_mmc_platform_data *mmc = dev->platform_data;
|
|
|
|
/*
|
|
* Assume TWL VMMC2 (hsmmc[1]) is used only to power the card ... OMAP
|
|
* VDDS is used to power the pins, optionally with a transceiver to
|
|
* support cards using voltages other than VDDS (1.8V nominal). When a
|
|
* transceiver is used, DAT3..7 are muxed as transceiver control pins.
|
|
*/
|
|
if (power_on) {
|
|
if (mmc->slots[0].internal_clock) {
|
|
u32 reg;
|
|
|
|
reg = omap_ctrl_readl(control_devconf1_offset);
|
|
reg |= OMAP2_MMCSDIO2ADPCLKISEL;
|
|
omap_ctrl_writel(reg, control_devconf1_offset);
|
|
}
|
|
ret = twl_mmc_set_voltage(c, vdd);
|
|
} else {
|
|
ret = twl_mmc_set_voltage(c, 0);
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int twl_mmc3_set_power(struct device *dev, int slot, int power_on,
|
|
int vdd)
|
|
{
|
|
/*
|
|
* Assume MMC3 has self-powered device connected, for example on-board
|
|
* chip with external power source.
|
|
*/
|
|
return 0;
|
|
}
|
|
|
|
static struct omap_mmc_platform_data *hsmmc_data[OMAP34XX_NR_MMC] __initdata;
|
|
|
|
void __init twl4030_mmc_init(struct twl4030_hsmmc_info *controllers)
|
|
{
|
|
struct twl4030_hsmmc_info *c;
|
|
int nr_hsmmc = ARRAY_SIZE(hsmmc_data);
|
|
|
|
if (cpu_is_omap2430()) {
|
|
control_pbias_offset = OMAP243X_CONTROL_PBIAS_LITE;
|
|
control_devconf1_offset = OMAP243X_CONTROL_DEVCONF1;
|
|
nr_hsmmc = 2;
|
|
} else {
|
|
control_pbias_offset = OMAP343X_CONTROL_PBIAS_LITE;
|
|
control_devconf1_offset = OMAP343X_CONTROL_DEVCONF1;
|
|
}
|
|
|
|
for (c = controllers; c->mmc; c++) {
|
|
struct twl_mmc_controller *twl = hsmmc + c->mmc - 1;
|
|
struct omap_mmc_platform_data *mmc = hsmmc_data[c->mmc - 1];
|
|
|
|
if (!c->mmc || c->mmc > nr_hsmmc) {
|
|
pr_debug("MMC%d: no such controller\n", c->mmc);
|
|
continue;
|
|
}
|
|
if (mmc) {
|
|
pr_debug("MMC%d: already configured\n", c->mmc);
|
|
continue;
|
|
}
|
|
|
|
mmc = kzalloc(sizeof(struct omap_mmc_platform_data), GFP_KERNEL);
|
|
if (!mmc) {
|
|
pr_err("Cannot allocate memory for mmc device!\n");
|
|
return;
|
|
}
|
|
|
|
if (c->name)
|
|
strncpy(twl->name, c->name, HSMMC_NAME_LEN);
|
|
else
|
|
snprintf(twl->name, ARRAY_SIZE(twl->name),
|
|
"mmc%islot%i", c->mmc, 1);
|
|
mmc->slots[0].name = twl->name;
|
|
mmc->nr_slots = 1;
|
|
mmc->slots[0].wires = c->wires;
|
|
mmc->slots[0].internal_clock = !c->ext_clock;
|
|
mmc->dma_mask = 0xffffffff;
|
|
|
|
/* note: twl4030 card detect GPIOs normally switch VMMCx ... */
|
|
if (gpio_is_valid(c->gpio_cd)) {
|
|
mmc->init = twl_mmc_late_init;
|
|
mmc->cleanup = twl_mmc_cleanup;
|
|
mmc->suspend = twl_mmc_suspend;
|
|
mmc->resume = twl_mmc_resume;
|
|
|
|
mmc->slots[0].switch_pin = c->gpio_cd;
|
|
mmc->slots[0].card_detect_irq = gpio_to_irq(c->gpio_cd);
|
|
if (c->cover_only)
|
|
mmc->slots[0].get_cover_state = twl_mmc_get_cover_state;
|
|
else
|
|
mmc->slots[0].card_detect = twl_mmc_card_detect;
|
|
} else
|
|
mmc->slots[0].switch_pin = -EINVAL;
|
|
|
|
/* write protect normally uses an OMAP gpio */
|
|
if (gpio_is_valid(c->gpio_wp)) {
|
|
gpio_request(c->gpio_wp, "mmc_wp");
|
|
gpio_direction_input(c->gpio_wp);
|
|
|
|
mmc->slots[0].gpio_wp = c->gpio_wp;
|
|
mmc->slots[0].get_ro = twl_mmc_get_ro;
|
|
} else
|
|
mmc->slots[0].gpio_wp = -EINVAL;
|
|
|
|
/* NOTE: we assume OMAP's MMC1 and MMC2 use
|
|
* the TWL4030's VMMC1 and VMMC2, respectively;
|
|
* and that MMC3 device has it's own power source.
|
|
*/
|
|
|
|
switch (c->mmc) {
|
|
case 1:
|
|
mmc->slots[0].set_power = twl_mmc1_set_power;
|
|
mmc->slots[0].ocr_mask = MMC1_OCR;
|
|
break;
|
|
case 2:
|
|
mmc->slots[0].set_power = twl_mmc2_set_power;
|
|
if (c->transceiver)
|
|
mmc->slots[0].ocr_mask = MMC2_OCR;
|
|
else
|
|
mmc->slots[0].ocr_mask = MMC_VDD_165_195;
|
|
break;
|
|
case 3:
|
|
mmc->slots[0].set_power = twl_mmc3_set_power;
|
|
mmc->slots[0].ocr_mask = MMC_VDD_165_195;
|
|
break;
|
|
default:
|
|
pr_err("MMC%d configuration not supported!\n", c->mmc);
|
|
kfree(mmc);
|
|
continue;
|
|
}
|
|
hsmmc_data[c->mmc - 1] = mmc;
|
|
}
|
|
|
|
omap2_init_mmc(hsmmc_data, OMAP34XX_NR_MMC);
|
|
|
|
/* pass the device nodes back to board setup code */
|
|
for (c = controllers; c->mmc; c++) {
|
|
struct omap_mmc_platform_data *mmc = hsmmc_data[c->mmc - 1];
|
|
|
|
if (!c->mmc || c->mmc > nr_hsmmc)
|
|
continue;
|
|
c->dev = mmc->dev;
|
|
}
|
|
}
|
|
|
|
#endif
|