147 lines
4.1 KiB
Plaintext
147 lines
4.1 KiB
Plaintext
Marvell Distributed Switch Architecture Device Tree Bindings
|
|
------------------------------------------------------------
|
|
|
|
Required properties:
|
|
- compatible : Should be "marvell,dsa"
|
|
- #address-cells : Must be 2, first cell is the address on the MDIO bus
|
|
and second cell is the address in the switch tree.
|
|
Second cell is used only when cascading/chaining.
|
|
- #size-cells : Must be 0
|
|
- dsa,ethernet : Should be a phandle to a valid Ethernet device node
|
|
- dsa,mii-bus : Should be a phandle to a valid MDIO bus device node
|
|
|
|
Optional properties:
|
|
- interrupts : property with a value describing the switch
|
|
interrupt number (not supported by the driver)
|
|
|
|
A DSA node can contain multiple switch chips which are therefore child nodes of
|
|
the parent DSA node. The maximum number of allowed child nodes is 4
|
|
(DSA_MAX_SWITCHES).
|
|
Each of these switch child nodes should have the following required properties:
|
|
|
|
- reg : Contains two fields. The first one describes the
|
|
address on the MII bus. The second is the switch
|
|
number that must be unique in cascaded configurations
|
|
- #address-cells : Must be 1
|
|
- #size-cells : Must be 0
|
|
|
|
A switch child node has the following optional property:
|
|
|
|
- eeprom-length : Set to the length of an EEPROM connected to the
|
|
switch. Must be set if the switch can not detect
|
|
the presence and/or size of a connected EEPROM,
|
|
otherwise optional.
|
|
- reset-gpios : phandle and specifier to a gpio line connected to
|
|
reset pin of the switch chip.
|
|
|
|
A switch may have multiple "port" children nodes
|
|
|
|
Each port children node must have the following mandatory properties:
|
|
- reg : Describes the port address in the switch
|
|
- label : Describes the label associated with this port, special
|
|
labels are "cpu" to indicate a CPU port and "dsa" to
|
|
indicate an uplink/downlink port.
|
|
|
|
Note that a port labelled "dsa" will imply checking for the uplink phandle
|
|
described below.
|
|
|
|
Optionnal property:
|
|
- link : Should be a list of phandles to another switch's DSA port.
|
|
This property is only used when switches are being
|
|
chained/cascaded together. This port is used as outgoing port
|
|
towards the phandle port, which can be more than one hop away.
|
|
|
|
- phy-handle : Phandle to a PHY on an external MDIO bus, not the
|
|
switch internal one. See
|
|
Documentation/devicetree/bindings/net/ethernet.txt
|
|
for details.
|
|
|
|
- phy-mode : String representing the connection to the designated
|
|
PHY node specified by the 'phy-handle' property. See
|
|
Documentation/devicetree/bindings/net/ethernet.txt
|
|
for details.
|
|
|
|
- mii-bus : Should be a phandle to a valid MDIO bus device node.
|
|
This mii-bus will be used in preference to the
|
|
global dsa,mii-bus defined above, for this switch.
|
|
|
|
Optional subnodes:
|
|
- fixed-link : Fixed-link subnode describing a link to a non-MDIO
|
|
managed entity. See
|
|
Documentation/devicetree/bindings/net/fixed-link.txt
|
|
for details.
|
|
|
|
Example:
|
|
|
|
dsa@0 {
|
|
compatible = "marvell,dsa";
|
|
#address-cells = <2>;
|
|
#size-cells = <0>;
|
|
|
|
interrupts = <10>;
|
|
dsa,ethernet = <ðernet0>;
|
|
dsa,mii-bus = <&mii_bus0>;
|
|
|
|
switch@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <16 0>; /* MDIO address 16, switch 0 in tree */
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
label = "lan1";
|
|
phy-handle = <&phy0>;
|
|
};
|
|
|
|
port@1 {
|
|
reg = <1>;
|
|
label = "lan2";
|
|
};
|
|
|
|
port@5 {
|
|
reg = <5>;
|
|
label = "cpu";
|
|
};
|
|
|
|
switch0port6: port@6 {
|
|
reg = <6>;
|
|
label = "dsa";
|
|
link = <&switch1port0
|
|
&switch2port0>;
|
|
};
|
|
};
|
|
|
|
switch@1 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <17 1>; /* MDIO address 17, switch 1 in tree */
|
|
mii-bus = <&mii_bus1>;
|
|
reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
|
|
|
|
switch1port0: port@0 {
|
|
reg = <0>;
|
|
label = "dsa";
|
|
link = <&switch0port6>;
|
|
};
|
|
switch1port1: port@1 {
|
|
reg = <1>;
|
|
label = "dsa";
|
|
link = <&switch2port1>;
|
|
};
|
|
};
|
|
|
|
switch@2 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <18 2>; /* MDIO address 18, switch 2 in tree */
|
|
mii-bus = <&mii_bus1>;
|
|
|
|
switch2port0: port@0 {
|
|
reg = <0>;
|
|
label = "dsa";
|
|
link = <&switch1port1
|
|
&switch0port6>;
|
|
};
|
|
};
|
|
};
|