641 lines
18 KiB
C
641 lines
18 KiB
C
// SPDX-License-Identifier: GPL-2.0
|
|
// Copyright (C) 2018 ROHM Semiconductors
|
|
// bd71837-regulator.c ROHM BD71837MWV regulator driver
|
|
|
|
#include <linux/kernel.h>
|
|
#include <linux/module.h>
|
|
#include <linux/init.h>
|
|
#include <linux/err.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/regulator/driver.h>
|
|
#include <linux/regulator/machine.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/slab.h>
|
|
#include <linux/gpio.h>
|
|
#include <linux/mfd/bd71837.h>
|
|
#include <linux/regulator/of_regulator.h>
|
|
|
|
struct bd71837_pmic {
|
|
struct regulator_desc descs[BD71837_REGULATOR_CNT];
|
|
struct bd71837 *mfd;
|
|
struct platform_device *pdev;
|
|
struct regulator_dev *rdev[BD71837_REGULATOR_CNT];
|
|
};
|
|
|
|
/*
|
|
* BUCK1/2/3/4
|
|
* BUCK1RAMPRATE[1:0] BUCK1 DVS ramp rate setting
|
|
* 00: 10.00mV/usec 10mV 1uS
|
|
* 01: 5.00mV/usec 10mV 2uS
|
|
* 10: 2.50mV/usec 10mV 4uS
|
|
* 11: 1.25mV/usec 10mV 8uS
|
|
*/
|
|
static int bd71837_buck1234_set_ramp_delay(struct regulator_dev *rdev,
|
|
int ramp_delay)
|
|
{
|
|
struct bd71837_pmic *pmic = rdev_get_drvdata(rdev);
|
|
struct bd71837 *mfd = pmic->mfd;
|
|
int id = rdev->desc->id;
|
|
unsigned int ramp_value = BUCK_RAMPRATE_10P00MV;
|
|
|
|
dev_dbg(&(pmic->pdev->dev), "Buck[%d] Set Ramp = %d\n", id + 1,
|
|
ramp_delay);
|
|
switch (ramp_delay) {
|
|
case 1 ... 1250:
|
|
ramp_value = BUCK_RAMPRATE_1P25MV;
|
|
break;
|
|
case 1251 ... 2500:
|
|
ramp_value = BUCK_RAMPRATE_2P50MV;
|
|
break;
|
|
case 2501 ... 5000:
|
|
ramp_value = BUCK_RAMPRATE_5P00MV;
|
|
break;
|
|
case 5001 ... 10000:
|
|
ramp_value = BUCK_RAMPRATE_10P00MV;
|
|
break;
|
|
default:
|
|
ramp_value = BUCK_RAMPRATE_10P00MV;
|
|
dev_err(&pmic->pdev->dev,
|
|
"%s: ramp_delay: %d not supported, setting 10000mV//us\n",
|
|
rdev->desc->name, ramp_delay);
|
|
}
|
|
|
|
return regmap_update_bits(mfd->regmap, BD71837_REG_BUCK1_CTRL + id,
|
|
BUCK_RAMPRATE_MASK, ramp_value << 6);
|
|
}
|
|
|
|
/* Bucks 1 to 4 support DVS. PWM mode is used when voltage is changed.
|
|
* Bucks 5 to 8 and LDOs can use PFM and must be disabled when voltage
|
|
* is changed. Hence we return -EBUSY for these if voltage is changed
|
|
* when BUCK/LDO is enabled.
|
|
*/
|
|
static int bd71837_set_voltage_sel_restricted(struct regulator_dev *rdev,
|
|
unsigned int sel)
|
|
{
|
|
int ret;
|
|
|
|
ret = regulator_is_enabled_regmap(rdev);
|
|
if (!ret)
|
|
ret = regulator_set_voltage_sel_regmap(rdev, sel);
|
|
else if (ret == 1)
|
|
ret = -EBUSY;
|
|
return ret;
|
|
}
|
|
|
|
static struct regulator_ops bd71837_ldo_regulator_ops = {
|
|
.enable = regulator_enable_regmap,
|
|
.disable = regulator_disable_regmap,
|
|
.is_enabled = regulator_is_enabled_regmap,
|
|
.list_voltage = regulator_list_voltage_linear_range,
|
|
.set_voltage_sel = bd71837_set_voltage_sel_restricted,
|
|
.get_voltage_sel = regulator_get_voltage_sel_regmap,
|
|
};
|
|
|
|
static struct regulator_ops bd71837_ldo_regulator_nolinear_ops = {
|
|
.enable = regulator_enable_regmap,
|
|
.disable = regulator_disable_regmap,
|
|
.is_enabled = regulator_is_enabled_regmap,
|
|
.list_voltage = regulator_list_voltage_table,
|
|
.set_voltage_sel = bd71837_set_voltage_sel_restricted,
|
|
.get_voltage_sel = regulator_get_voltage_sel_regmap,
|
|
};
|
|
|
|
static struct regulator_ops bd71837_buck_regulator_ops = {
|
|
.enable = regulator_enable_regmap,
|
|
.disable = regulator_disable_regmap,
|
|
.is_enabled = regulator_is_enabled_regmap,
|
|
.list_voltage = regulator_list_voltage_linear_range,
|
|
.set_voltage_sel = bd71837_set_voltage_sel_restricted,
|
|
.get_voltage_sel = regulator_get_voltage_sel_regmap,
|
|
.set_voltage_time_sel = regulator_set_voltage_time_sel,
|
|
};
|
|
|
|
static struct regulator_ops bd71837_buck_regulator_nolinear_ops = {
|
|
.enable = regulator_enable_regmap,
|
|
.disable = regulator_disable_regmap,
|
|
.is_enabled = regulator_is_enabled_regmap,
|
|
.list_voltage = regulator_list_voltage_table,
|
|
.set_voltage_sel = bd71837_set_voltage_sel_restricted,
|
|
.get_voltage_sel = regulator_get_voltage_sel_regmap,
|
|
.set_voltage_time_sel = regulator_set_voltage_time_sel,
|
|
};
|
|
|
|
static struct regulator_ops bd71837_buck1234_regulator_ops = {
|
|
.enable = regulator_enable_regmap,
|
|
.disable = regulator_disable_regmap,
|
|
.is_enabled = regulator_is_enabled_regmap,
|
|
.list_voltage = regulator_list_voltage_linear_range,
|
|
.set_voltage_sel = regulator_set_voltage_sel_regmap,
|
|
.get_voltage_sel = regulator_get_voltage_sel_regmap,
|
|
.set_voltage_time_sel = regulator_set_voltage_time_sel,
|
|
.set_ramp_delay = bd71837_buck1234_set_ramp_delay,
|
|
};
|
|
|
|
/*
|
|
* BUCK1/2/3/4
|
|
* 0.70 to 1.30V (10mV step)
|
|
*/
|
|
static const struct regulator_linear_range bd71837_buck1234_voltage_ranges[] = {
|
|
REGULATOR_LINEAR_RANGE(700000, 0x00, 0x3C, 10000),
|
|
REGULATOR_LINEAR_RANGE(1300000, 0x3D, 0x3F, 0),
|
|
};
|
|
|
|
/*
|
|
* BUCK5
|
|
* 0.9V to 1.35V ()
|
|
*/
|
|
static const struct regulator_linear_range bd71837_buck5_voltage_ranges[] = {
|
|
REGULATOR_LINEAR_RANGE(700000, 0x00, 0x03, 100000),
|
|
REGULATOR_LINEAR_RANGE(1050000, 0x04, 0x05, 50000),
|
|
REGULATOR_LINEAR_RANGE(1200000, 0x06, 0x07, 150000),
|
|
};
|
|
|
|
/*
|
|
* BUCK6
|
|
* 3.0V to 3.3V (step 100mV)
|
|
*/
|
|
static const struct regulator_linear_range bd71837_buck6_voltage_ranges[] = {
|
|
REGULATOR_LINEAR_RANGE(3000000, 0x00, 0x03, 100000),
|
|
};
|
|
|
|
/*
|
|
* BUCK7
|
|
* 000 = 1.605V
|
|
* 001 = 1.695V
|
|
* 010 = 1.755V
|
|
* 011 = 1.8V (Initial)
|
|
* 100 = 1.845V
|
|
* 101 = 1.905V
|
|
* 110 = 1.95V
|
|
* 111 = 1.995V
|
|
*/
|
|
static const unsigned int buck_7_volts[] = {
|
|
1605000, 1695000, 1755000, 1800000, 1845000, 1905000, 1950000, 1995000
|
|
};
|
|
|
|
/*
|
|
* BUCK8
|
|
* 0.8V to 1.40V (step 10mV)
|
|
*/
|
|
static const struct regulator_linear_range bd71837_buck8_voltage_ranges[] = {
|
|
REGULATOR_LINEAR_RANGE(800000, 0x00, 0x3C, 10000),
|
|
REGULATOR_LINEAR_RANGE(1400000, 0x3D, 0x3F, 0),
|
|
};
|
|
|
|
/*
|
|
* LDO1
|
|
* 3.0 to 3.3V (100mV step)
|
|
*/
|
|
static const struct regulator_linear_range bd71837_ldo1_voltage_ranges[] = {
|
|
REGULATOR_LINEAR_RANGE(3000000, 0x00, 0x03, 100000),
|
|
};
|
|
|
|
/*
|
|
* LDO2
|
|
* 0.8 or 0.9V
|
|
*/
|
|
const unsigned int ldo_2_volts[] = {
|
|
900000, 800000
|
|
};
|
|
|
|
/*
|
|
* LDO3
|
|
* 1.8 to 3.3V (100mV step)
|
|
*/
|
|
static const struct regulator_linear_range bd71837_ldo3_voltage_ranges[] = {
|
|
REGULATOR_LINEAR_RANGE(1800000, 0x00, 0x0F, 100000),
|
|
};
|
|
|
|
/*
|
|
* LDO4
|
|
* 0.9 to 1.8V (100mV step)
|
|
*/
|
|
static const struct regulator_linear_range bd71837_ldo4_voltage_ranges[] = {
|
|
REGULATOR_LINEAR_RANGE(900000, 0x00, 0x09, 100000),
|
|
REGULATOR_LINEAR_RANGE(1800000, 0x0A, 0x0F, 0),
|
|
};
|
|
|
|
/*
|
|
* LDO5
|
|
* 1.8 to 3.3V (100mV step)
|
|
*/
|
|
static const struct regulator_linear_range bd71837_ldo5_voltage_ranges[] = {
|
|
REGULATOR_LINEAR_RANGE(1800000, 0x00, 0x0F, 100000),
|
|
};
|
|
|
|
/*
|
|
* LDO6
|
|
* 0.9 to 1.8V (100mV step)
|
|
*/
|
|
static const struct regulator_linear_range bd71837_ldo6_voltage_ranges[] = {
|
|
REGULATOR_LINEAR_RANGE(900000, 0x00, 0x09, 100000),
|
|
REGULATOR_LINEAR_RANGE(1800000, 0x0A, 0x0F, 0),
|
|
};
|
|
|
|
/*
|
|
* LDO7
|
|
* 1.8 to 3.3V (100mV step)
|
|
*/
|
|
static const struct regulator_linear_range bd71837_ldo7_voltage_ranges[] = {
|
|
REGULATOR_LINEAR_RANGE(1800000, 0x00, 0x0F, 100000),
|
|
};
|
|
|
|
static const struct regulator_desc bd71837_regulators[] = {
|
|
{
|
|
.name = "buck1",
|
|
.of_match = of_match_ptr("BUCK1"),
|
|
.regulators_node = of_match_ptr("regulators"),
|
|
.id = BD71837_BUCK1,
|
|
.ops = &bd71837_buck1234_regulator_ops,
|
|
.type = REGULATOR_VOLTAGE,
|
|
.n_voltages = BD71837_BUCK1_VOLTAGE_NUM,
|
|
.linear_ranges = bd71837_buck1234_voltage_ranges,
|
|
.n_linear_ranges = ARRAY_SIZE(bd71837_buck1234_voltage_ranges),
|
|
.vsel_reg = BD71837_REG_BUCK1_VOLT_RUN,
|
|
.vsel_mask = BUCK1_RUN_MASK,
|
|
.enable_reg = BD71837_REG_BUCK1_CTRL,
|
|
.enable_mask = BD71837_BUCK_EN,
|
|
.owner = THIS_MODULE,
|
|
},
|
|
{
|
|
.name = "buck2",
|
|
.of_match = of_match_ptr("BUCK2"),
|
|
.regulators_node = of_match_ptr("regulators"),
|
|
.id = BD71837_BUCK2,
|
|
.ops = &bd71837_buck1234_regulator_ops,
|
|
.type = REGULATOR_VOLTAGE,
|
|
.n_voltages = BD71837_BUCK2_VOLTAGE_NUM,
|
|
.linear_ranges = bd71837_buck1234_voltage_ranges,
|
|
.n_linear_ranges = ARRAY_SIZE(bd71837_buck1234_voltage_ranges),
|
|
.vsel_reg = BD71837_REG_BUCK2_VOLT_RUN,
|
|
.vsel_mask = BUCK2_RUN_MASK,
|
|
.enable_reg = BD71837_REG_BUCK2_CTRL,
|
|
.enable_mask = BD71837_BUCK_EN,
|
|
.owner = THIS_MODULE,
|
|
},
|
|
{
|
|
.name = "buck3",
|
|
.of_match = of_match_ptr("BUCK3"),
|
|
.regulators_node = of_match_ptr("regulators"),
|
|
.id = BD71837_BUCK3,
|
|
.ops = &bd71837_buck1234_regulator_ops,
|
|
.type = REGULATOR_VOLTAGE,
|
|
.n_voltages = BD71837_BUCK3_VOLTAGE_NUM,
|
|
.linear_ranges = bd71837_buck1234_voltage_ranges,
|
|
.n_linear_ranges = ARRAY_SIZE(bd71837_buck1234_voltage_ranges),
|
|
.vsel_reg = BD71837_REG_BUCK3_VOLT_RUN,
|
|
.vsel_mask = BUCK3_RUN_MASK,
|
|
.enable_reg = BD71837_REG_BUCK3_CTRL,
|
|
.enable_mask = BD71837_BUCK_EN,
|
|
.owner = THIS_MODULE,
|
|
},
|
|
{
|
|
.name = "buck4",
|
|
.of_match = of_match_ptr("BUCK4"),
|
|
.regulators_node = of_match_ptr("regulators"),
|
|
.id = BD71837_BUCK4,
|
|
.ops = &bd71837_buck1234_regulator_ops,
|
|
.type = REGULATOR_VOLTAGE,
|
|
.n_voltages = BD71837_BUCK4_VOLTAGE_NUM,
|
|
.linear_ranges = bd71837_buck1234_voltage_ranges,
|
|
.n_linear_ranges = ARRAY_SIZE(bd71837_buck1234_voltage_ranges),
|
|
.vsel_reg = BD71837_REG_BUCK4_VOLT_RUN,
|
|
.vsel_mask = BUCK4_RUN_MASK,
|
|
.enable_reg = BD71837_REG_BUCK4_CTRL,
|
|
.enable_mask = BD71837_BUCK_EN,
|
|
.owner = THIS_MODULE,
|
|
},
|
|
{
|
|
.name = "buck5",
|
|
.of_match = of_match_ptr("BUCK5"),
|
|
.regulators_node = of_match_ptr("regulators"),
|
|
.id = BD71837_BUCK5,
|
|
.ops = &bd71837_buck_regulator_ops,
|
|
.type = REGULATOR_VOLTAGE,
|
|
.n_voltages = BD71837_BUCK5_VOLTAGE_NUM,
|
|
.linear_ranges = bd71837_buck5_voltage_ranges,
|
|
.n_linear_ranges = ARRAY_SIZE(bd71837_buck5_voltage_ranges),
|
|
.vsel_reg = BD71837_REG_BUCK5_VOLT,
|
|
.vsel_mask = BUCK5_MASK,
|
|
.enable_reg = BD71837_REG_BUCK5_CTRL,
|
|
.enable_mask = BD71837_BUCK_EN,
|
|
.owner = THIS_MODULE,
|
|
},
|
|
{
|
|
.name = "buck6",
|
|
.of_match = of_match_ptr("BUCK6"),
|
|
.regulators_node = of_match_ptr("regulators"),
|
|
.id = BD71837_BUCK6,
|
|
.ops = &bd71837_buck_regulator_ops,
|
|
.type = REGULATOR_VOLTAGE,
|
|
.n_voltages = BD71837_BUCK6_VOLTAGE_NUM,
|
|
.linear_ranges = bd71837_buck6_voltage_ranges,
|
|
.n_linear_ranges = ARRAY_SIZE(bd71837_buck6_voltage_ranges),
|
|
.vsel_reg = BD71837_REG_BUCK6_VOLT,
|
|
.vsel_mask = BUCK6_MASK,
|
|
.enable_reg = BD71837_REG_BUCK6_CTRL,
|
|
.enable_mask = BD71837_BUCK_EN,
|
|
.owner = THIS_MODULE,
|
|
},
|
|
{
|
|
.name = "buck7",
|
|
.of_match = of_match_ptr("BUCK7"),
|
|
.regulators_node = of_match_ptr("regulators"),
|
|
.id = BD71837_BUCK7,
|
|
.ops = &bd71837_buck_regulator_nolinear_ops,
|
|
.type = REGULATOR_VOLTAGE,
|
|
.volt_table = &buck_7_volts[0],
|
|
.n_voltages = ARRAY_SIZE(buck_7_volts),
|
|
.vsel_reg = BD71837_REG_BUCK7_VOLT,
|
|
.vsel_mask = BUCK7_MASK,
|
|
.enable_reg = BD71837_REG_BUCK7_CTRL,
|
|
.enable_mask = BD71837_BUCK_EN,
|
|
.owner = THIS_MODULE,
|
|
},
|
|
{
|
|
.name = "buck8",
|
|
.of_match = of_match_ptr("BUCK8"),
|
|
.regulators_node = of_match_ptr("regulators"),
|
|
.id = BD71837_BUCK8,
|
|
.ops = &bd71837_buck_regulator_ops,
|
|
.type = REGULATOR_VOLTAGE,
|
|
.n_voltages = BD71837_BUCK8_VOLTAGE_NUM,
|
|
.linear_ranges = bd71837_buck8_voltage_ranges,
|
|
.n_linear_ranges = ARRAY_SIZE(bd71837_buck8_voltage_ranges),
|
|
.vsel_reg = BD71837_REG_BUCK8_VOLT,
|
|
.vsel_mask = BUCK8_MASK,
|
|
.enable_reg = BD71837_REG_BUCK8_CTRL,
|
|
.enable_mask = BD71837_BUCK_EN,
|
|
.owner = THIS_MODULE,
|
|
},
|
|
{
|
|
.name = "ldo1",
|
|
.of_match = of_match_ptr("LDO1"),
|
|
.regulators_node = of_match_ptr("regulators"),
|
|
.id = BD71837_LDO1,
|
|
.ops = &bd71837_ldo_regulator_ops,
|
|
.type = REGULATOR_VOLTAGE,
|
|
.n_voltages = BD71837_LDO1_VOLTAGE_NUM,
|
|
.linear_ranges = bd71837_ldo1_voltage_ranges,
|
|
.n_linear_ranges = ARRAY_SIZE(bd71837_ldo1_voltage_ranges),
|
|
.vsel_reg = BD71837_REG_LDO1_VOLT,
|
|
.vsel_mask = LDO1_MASK,
|
|
.enable_reg = BD71837_REG_LDO1_VOLT,
|
|
.enable_mask = BD71837_LDO_EN,
|
|
.owner = THIS_MODULE,
|
|
},
|
|
{
|
|
.name = "ldo2",
|
|
.of_match = of_match_ptr("LDO2"),
|
|
.regulators_node = of_match_ptr("regulators"),
|
|
.id = BD71837_LDO2,
|
|
.ops = &bd71837_ldo_regulator_nolinear_ops,
|
|
.type = REGULATOR_VOLTAGE,
|
|
.volt_table = &ldo_2_volts[0],
|
|
.vsel_reg = BD71837_REG_LDO2_VOLT,
|
|
.vsel_mask = LDO2_MASK,
|
|
.n_voltages = ARRAY_SIZE(ldo_2_volts),
|
|
.n_voltages = BD71837_LDO2_VOLTAGE_NUM,
|
|
.enable_reg = BD71837_REG_LDO2_VOLT,
|
|
.enable_mask = BD71837_LDO_EN,
|
|
.owner = THIS_MODULE,
|
|
},
|
|
{
|
|
.name = "ldo3",
|
|
.of_match = of_match_ptr("LDO3"),
|
|
.regulators_node = of_match_ptr("regulators"),
|
|
.id = BD71837_LDO3,
|
|
.ops = &bd71837_ldo_regulator_ops,
|
|
.type = REGULATOR_VOLTAGE,
|
|
.n_voltages = BD71837_LDO3_VOLTAGE_NUM,
|
|
.linear_ranges = bd71837_ldo3_voltage_ranges,
|
|
.n_linear_ranges = ARRAY_SIZE(bd71837_ldo3_voltage_ranges),
|
|
.vsel_reg = BD71837_REG_LDO3_VOLT,
|
|
.vsel_mask = LDO3_MASK,
|
|
.enable_reg = BD71837_REG_LDO3_VOLT,
|
|
.enable_mask = BD71837_LDO_EN,
|
|
.owner = THIS_MODULE,
|
|
},
|
|
{
|
|
.name = "ldo4",
|
|
.of_match = of_match_ptr("LDO4"),
|
|
.regulators_node = of_match_ptr("regulators"),
|
|
.id = BD71837_LDO4,
|
|
.ops = &bd71837_ldo_regulator_ops,
|
|
.type = REGULATOR_VOLTAGE,
|
|
.n_voltages = BD71837_LDO4_VOLTAGE_NUM,
|
|
.linear_ranges = bd71837_ldo4_voltage_ranges,
|
|
.n_linear_ranges = ARRAY_SIZE(bd71837_ldo4_voltage_ranges),
|
|
.vsel_reg = BD71837_REG_LDO4_VOLT,
|
|
.vsel_mask = LDO4_MASK,
|
|
.enable_reg = BD71837_REG_LDO4_VOLT,
|
|
.enable_mask = BD71837_LDO_EN,
|
|
.owner = THIS_MODULE,
|
|
},
|
|
{
|
|
.name = "ldo5",
|
|
.of_match = of_match_ptr("LDO5"),
|
|
.regulators_node = of_match_ptr("regulators"),
|
|
.id = BD71837_LDO5,
|
|
.ops = &bd71837_ldo_regulator_ops,
|
|
.type = REGULATOR_VOLTAGE,
|
|
.n_voltages = BD71837_LDO5_VOLTAGE_NUM,
|
|
.linear_ranges = bd71837_ldo5_voltage_ranges,
|
|
.n_linear_ranges = ARRAY_SIZE(bd71837_ldo5_voltage_ranges),
|
|
/* LDO5 is supplied by buck6 */
|
|
.supply_name = "buck6",
|
|
.vsel_reg = BD71837_REG_LDO5_VOLT,
|
|
.vsel_mask = LDO5_MASK,
|
|
.enable_reg = BD71837_REG_LDO5_VOLT,
|
|
.enable_mask = BD71837_LDO_EN,
|
|
.owner = THIS_MODULE,
|
|
},
|
|
{
|
|
.name = "ldo6",
|
|
.of_match = of_match_ptr("LDO6"),
|
|
.regulators_node = of_match_ptr("regulators"),
|
|
.id = BD71837_LDO6,
|
|
.ops = &bd71837_ldo_regulator_ops,
|
|
.type = REGULATOR_VOLTAGE,
|
|
.n_voltages = BD71837_LDO6_VOLTAGE_NUM,
|
|
.linear_ranges = bd71837_ldo6_voltage_ranges,
|
|
.n_linear_ranges = ARRAY_SIZE(bd71837_ldo6_voltage_ranges),
|
|
/* LDO6 is supplied by buck7 */
|
|
.supply_name = "buck7",
|
|
.vsel_reg = BD71837_REG_LDO6_VOLT,
|
|
.vsel_mask = LDO6_MASK,
|
|
.enable_reg = BD71837_REG_LDO6_VOLT,
|
|
.enable_mask = BD71837_LDO_EN,
|
|
.owner = THIS_MODULE,
|
|
},
|
|
{
|
|
.name = "ldo7",
|
|
.of_match = of_match_ptr("LDO7"),
|
|
.regulators_node = of_match_ptr("regulators"),
|
|
.id = BD71837_LDO7,
|
|
.ops = &bd71837_ldo_regulator_ops,
|
|
.type = REGULATOR_VOLTAGE,
|
|
.n_voltages = BD71837_LDO7_VOLTAGE_NUM,
|
|
.linear_ranges = bd71837_ldo7_voltage_ranges,
|
|
.n_linear_ranges = ARRAY_SIZE(bd71837_ldo7_voltage_ranges),
|
|
.vsel_reg = BD71837_REG_LDO7_VOLT,
|
|
.vsel_mask = LDO7_MASK,
|
|
.enable_reg = BD71837_REG_LDO7_VOLT,
|
|
.enable_mask = BD71837_LDO_EN,
|
|
.owner = THIS_MODULE,
|
|
},
|
|
};
|
|
|
|
struct reg_init {
|
|
unsigned int reg;
|
|
unsigned int mask;
|
|
};
|
|
|
|
static int bd71837_probe(struct platform_device *pdev)
|
|
{
|
|
struct bd71837_pmic *pmic;
|
|
struct bd71837_board *pdata;
|
|
struct regulator_config config = { 0 };
|
|
struct reg_init pmic_regulator_inits[] = {
|
|
{
|
|
.reg = BD71837_REG_BUCK1_CTRL,
|
|
.mask = BD71837_BUCK_SEL,
|
|
}, {
|
|
.reg = BD71837_REG_BUCK2_CTRL,
|
|
.mask = BD71837_BUCK_SEL,
|
|
}, {
|
|
.reg = BD71837_REG_BUCK3_CTRL,
|
|
.mask = BD71837_BUCK_SEL,
|
|
}, {
|
|
.reg = BD71837_REG_BUCK4_CTRL,
|
|
.mask = BD71837_BUCK_SEL,
|
|
}, {
|
|
.reg = BD71837_REG_BUCK5_CTRL,
|
|
.mask = BD71837_BUCK_SEL,
|
|
}, {
|
|
.reg = BD71837_REG_BUCK6_CTRL,
|
|
.mask = BD71837_BUCK_SEL,
|
|
}, {
|
|
.reg = BD71837_REG_BUCK7_CTRL,
|
|
.mask = BD71837_BUCK_SEL,
|
|
}, {
|
|
.reg = BD71837_REG_BUCK8_CTRL,
|
|
.mask = BD71837_BUCK_SEL,
|
|
}, {
|
|
.reg = BD71837_REG_LDO1_VOLT,
|
|
.mask = BD71837_LDO_SEL,
|
|
}, {
|
|
.reg = BD71837_REG_LDO2_VOLT,
|
|
.mask = BD71837_LDO_SEL,
|
|
}, {
|
|
.reg = BD71837_REG_LDO3_VOLT,
|
|
.mask = BD71837_LDO_SEL,
|
|
}, {
|
|
.reg = BD71837_REG_LDO4_VOLT,
|
|
.mask = BD71837_LDO_SEL,
|
|
}, {
|
|
.reg = BD71837_REG_LDO5_VOLT,
|
|
.mask = BD71837_LDO_SEL,
|
|
}, {
|
|
.reg = BD71837_REG_LDO6_VOLT,
|
|
.mask = BD71837_LDO_SEL,
|
|
}, {
|
|
.reg = BD71837_REG_LDO7_VOLT,
|
|
.mask = BD71837_LDO_SEL,
|
|
}
|
|
};
|
|
|
|
int i, err;
|
|
|
|
pmic = devm_kzalloc(&pdev->dev, sizeof(struct bd71837_pmic),
|
|
GFP_KERNEL);
|
|
if (!pmic)
|
|
return -ENOMEM;
|
|
|
|
memcpy(pmic->descs, bd71837_regulators, sizeof(pmic->descs));
|
|
|
|
pmic->pdev = pdev;
|
|
pmic->mfd = dev_get_drvdata(pdev->dev.parent);
|
|
|
|
if (!pmic->mfd) {
|
|
dev_err(&pdev->dev, "No MFD driver data\n");
|
|
err = -EINVAL;
|
|
goto err;
|
|
}
|
|
platform_set_drvdata(pdev, pmic);
|
|
pdata = dev_get_platdata(pmic->mfd->dev);
|
|
|
|
/* Register LOCK release */
|
|
err = regmap_update_bits(pmic->mfd->regmap, BD71837_REG_REGLOCK,
|
|
(REGLOCK_PWRSEQ | REGLOCK_VREG), 0);
|
|
if (err) {
|
|
dev_err(&pmic->pdev->dev, "Failed to unlock PMIC (%d)\n", err);
|
|
goto err;
|
|
} else {
|
|
dev_dbg(&pmic->pdev->dev, "%s: Unlocked lock register 0x%x\n",
|
|
__func__, BD71837_REG_REGLOCK);
|
|
}
|
|
|
|
for (i = 0; i < ARRAY_SIZE(pmic_regulator_inits); i++) {
|
|
|
|
struct regulator_desc *desc;
|
|
struct regulator_dev *rdev;
|
|
|
|
desc = &pmic->descs[i];
|
|
|
|
if (pdata)
|
|
config.init_data = pdata->init_data[i];
|
|
|
|
config.dev = pdev->dev.parent;
|
|
config.driver_data = pmic;
|
|
config.regmap = pmic->mfd->regmap;
|
|
|
|
rdev = devm_regulator_register(&pdev->dev, desc, &config);
|
|
if (IS_ERR(rdev)) {
|
|
dev_err(pmic->mfd->dev,
|
|
"failed to register %s regulator\n",
|
|
desc->name);
|
|
err = PTR_ERR(rdev);
|
|
goto err;
|
|
}
|
|
/* Regulator register gets the regulator constraints and
|
|
* applies them (set_machine_constraints). This should have
|
|
* turned the control register(s) to correct values and we
|
|
* can now switch the control from PMIC state machine to the
|
|
* register interface
|
|
*/
|
|
err = regmap_update_bits(pmic->mfd->regmap,
|
|
pmic_regulator_inits[i].reg,
|
|
pmic_regulator_inits[i].mask,
|
|
0xFFFFFFFF);
|
|
if (err) {
|
|
dev_err(&pmic->pdev->dev,
|
|
"Failed to write BUCK/LDO SEL bit for (%s)\n",
|
|
desc->name);
|
|
goto err;
|
|
}
|
|
|
|
pmic->rdev[i] = rdev;
|
|
}
|
|
|
|
return 0;
|
|
|
|
err:
|
|
return err;
|
|
}
|
|
|
|
static struct platform_driver bd71837_regulator = {
|
|
.driver = {
|
|
.name = "bd71837-pmic",
|
|
.owner = THIS_MODULE,
|
|
},
|
|
.probe = bd71837_probe,
|
|
};
|
|
|
|
module_platform_driver(bd71837_regulator);
|
|
|
|
MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
|
|
MODULE_DESCRIPTION("BD71837 voltage regulator driver");
|
|
MODULE_LICENSE("GPL");
|