310 lines
9.6 KiB
C
310 lines
9.6 KiB
C
/*
|
|
* init_ohci1394_dma.c - Initializes physical DMA on all OHCI 1394 controllers
|
|
*
|
|
* Copyright (C) 2006-2007 Bernhard Kaindl <bk@suse.de>
|
|
*
|
|
* Derived from drivers/ieee1394/ohci1394.c and arch/x86/kernel/early-quirks.c
|
|
* this file has functions to:
|
|
* - scan the PCI very early on boot for all OHCI 1394-compliant controllers
|
|
* - reset and initialize them and make them join the IEEE1394 bus and
|
|
* - enable physical DMA on them to allow remote debugging
|
|
*
|
|
* All code and data is marked as __init and __initdata, respective as
|
|
* during boot, all OHCI1394 controllers may be claimed by the firewire
|
|
* stack and at this point, this code should not touch them anymore.
|
|
*
|
|
* To use physical DMA after the initialization of the firewire stack,
|
|
* be sure that the stack enables it and (re-)attach after the bus reset
|
|
* which may be caused by the firewire stack initialization.
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation; either version 2 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software Foundation,
|
|
* Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
|
|
*/
|
|
|
|
#include <linux/delay.h>
|
|
#include <linux/io.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/pci.h> /* for PCI defines */
|
|
#include <linux/string.h>
|
|
|
|
#include <asm/pci-direct.h> /* for direct PCI config space access */
|
|
#include <asm/fixmap.h>
|
|
|
|
#include <linux/init_ohci1394_dma.h>
|
|
#include "ohci.h"
|
|
|
|
int __initdata init_ohci1394_dma_early;
|
|
|
|
struct ohci {
|
|
void __iomem *registers;
|
|
};
|
|
|
|
static inline void reg_write(const struct ohci *ohci, int offset, u32 data)
|
|
{
|
|
writel(data, ohci->registers + offset);
|
|
}
|
|
|
|
static inline u32 reg_read(const struct ohci *ohci, int offset)
|
|
{
|
|
return readl(ohci->registers + offset);
|
|
}
|
|
|
|
#define OHCI_LOOP_COUNT 100 /* Number of loops for reg read waits */
|
|
|
|
/* Reads a PHY register of an OHCI-1394 controller */
|
|
static inline u8 __init get_phy_reg(struct ohci *ohci, u8 addr)
|
|
{
|
|
int i;
|
|
u32 r;
|
|
|
|
reg_write(ohci, OHCI1394_PhyControl, (addr << 8) | 0x00008000);
|
|
|
|
for (i = 0; i < OHCI_LOOP_COUNT; i++) {
|
|
if (reg_read(ohci, OHCI1394_PhyControl) & 0x80000000)
|
|
break;
|
|
mdelay(1);
|
|
}
|
|
r = reg_read(ohci, OHCI1394_PhyControl);
|
|
|
|
return (r & 0x00ff0000) >> 16;
|
|
}
|
|
|
|
/* Writes to a PHY register of an OHCI-1394 controller */
|
|
static inline void __init set_phy_reg(struct ohci *ohci, u8 addr, u8 data)
|
|
{
|
|
int i;
|
|
|
|
reg_write(ohci, OHCI1394_PhyControl, (addr << 8) | data | 0x00004000);
|
|
|
|
for (i = 0; i < OHCI_LOOP_COUNT; i++) {
|
|
if (!(reg_read(ohci, OHCI1394_PhyControl) & 0x00004000))
|
|
break;
|
|
mdelay(1);
|
|
}
|
|
}
|
|
|
|
/* Resets an OHCI-1394 controller (for sane state before initialization) */
|
|
static inline void __init init_ohci1394_soft_reset(struct ohci *ohci)
|
|
{
|
|
int i;
|
|
|
|
reg_write(ohci, OHCI1394_HCControlSet, OHCI1394_HCControl_softReset);
|
|
|
|
for (i = 0; i < OHCI_LOOP_COUNT; i++) {
|
|
if (!(reg_read(ohci, OHCI1394_HCControlSet)
|
|
& OHCI1394_HCControl_softReset))
|
|
break;
|
|
mdelay(1);
|
|
}
|
|
}
|
|
|
|
#define OHCI1394_MAX_AT_REQ_RETRIES 0xf
|
|
#define OHCI1394_MAX_AT_RESP_RETRIES 0x2
|
|
#define OHCI1394_MAX_PHYS_RESP_RETRIES 0x8
|
|
|
|
/* Basic OHCI-1394 register and port inititalization */
|
|
static inline void __init init_ohci1394_initialize(struct ohci *ohci)
|
|
{
|
|
u32 bus_options;
|
|
int num_ports, i;
|
|
|
|
/* Put some defaults to these undefined bus options */
|
|
bus_options = reg_read(ohci, OHCI1394_BusOptions);
|
|
bus_options |= 0x60000000; /* Enable CMC and ISC */
|
|
bus_options &= ~0x00ff0000; /* XXX: Set cyc_clk_acc to zero for now */
|
|
bus_options &= ~0x18000000; /* Disable PMC and BMC */
|
|
reg_write(ohci, OHCI1394_BusOptions, bus_options);
|
|
|
|
/* Set the bus number */
|
|
reg_write(ohci, OHCI1394_NodeID, 0x0000ffc0);
|
|
|
|
/* Enable posted writes */
|
|
reg_write(ohci, OHCI1394_HCControlSet,
|
|
OHCI1394_HCControl_postedWriteEnable);
|
|
|
|
/* Clear link control register */
|
|
reg_write(ohci, OHCI1394_LinkControlClear, 0xffffffff);
|
|
|
|
/* enable phys */
|
|
reg_write(ohci, OHCI1394_LinkControlSet,
|
|
OHCI1394_LinkControl_rcvPhyPkt);
|
|
|
|
/* Don't accept phy packets into AR request context */
|
|
reg_write(ohci, OHCI1394_LinkControlClear, 0x00000400);
|
|
|
|
/* Clear the Isochonouys interrupt masks */
|
|
reg_write(ohci, OHCI1394_IsoRecvIntMaskClear, 0xffffffff);
|
|
reg_write(ohci, OHCI1394_IsoRecvIntEventClear, 0xffffffff);
|
|
reg_write(ohci, OHCI1394_IsoXmitIntMaskClear, 0xffffffff);
|
|
reg_write(ohci, OHCI1394_IsoXmitIntEventClear, 0xffffffff);
|
|
|
|
/* Accept asynchronous transfer requests from all nodes for now */
|
|
reg_write(ohci, OHCI1394_AsReqFilterHiSet, 0x80000000);
|
|
|
|
/* Specify asynchronous transfer retries */
|
|
reg_write(ohci, OHCI1394_ATRetries,
|
|
OHCI1394_MAX_AT_REQ_RETRIES |
|
|
(OHCI1394_MAX_AT_RESP_RETRIES<<4) |
|
|
(OHCI1394_MAX_PHYS_RESP_RETRIES<<8));
|
|
|
|
/* We don't want hardware swapping */
|
|
reg_write(ohci, OHCI1394_HCControlClear,
|
|
OHCI1394_HCControl_noByteSwapData);
|
|
|
|
/* Enable link */
|
|
reg_write(ohci, OHCI1394_HCControlSet, OHCI1394_HCControl_linkEnable);
|
|
|
|
/* If anything is connected to a port, make sure it is enabled */
|
|
num_ports = get_phy_reg(ohci, 2) & 0xf;
|
|
for (i = 0; i < num_ports; i++) {
|
|
unsigned int status;
|
|
|
|
set_phy_reg(ohci, 7, i);
|
|
status = get_phy_reg(ohci, 8);
|
|
|
|
if (status & 0x20)
|
|
set_phy_reg(ohci, 8, status & ~1);
|
|
}
|
|
}
|
|
|
|
/**
|
|
* init_ohci1394_wait_for_busresets - wait until bus resets are completed
|
|
*
|
|
* OHCI1394 initialization itself and any device going on- or offline
|
|
* and any cable issue cause a IEEE1394 bus reset. The OHCI1394 spec
|
|
* specifies that physical DMA is disabled on each bus reset and it
|
|
* has to be enabled after each bus reset when needed. We resort
|
|
* to polling here because on early boot, we have no interrupts.
|
|
*/
|
|
static inline void __init init_ohci1394_wait_for_busresets(struct ohci *ohci)
|
|
{
|
|
int i, events;
|
|
|
|
for (i = 0; i < 9; i++) {
|
|
mdelay(200);
|
|
events = reg_read(ohci, OHCI1394_IntEventSet);
|
|
if (events & OHCI1394_busReset)
|
|
reg_write(ohci, OHCI1394_IntEventClear,
|
|
OHCI1394_busReset);
|
|
}
|
|
}
|
|
|
|
/**
|
|
* init_ohci1394_enable_physical_dma - Enable physical DMA for remote debugging
|
|
* This enables remote DMA access over IEEE1394 from every host for the low
|
|
* 4GB of address space. DMA accesses above 4GB are not available currently.
|
|
*/
|
|
static inline void __init init_ohci1394_enable_physical_dma(struct ohci *ohci)
|
|
{
|
|
reg_write(ohci, OHCI1394_PhyReqFilterHiSet, 0xffffffff);
|
|
reg_write(ohci, OHCI1394_PhyReqFilterLoSet, 0xffffffff);
|
|
reg_write(ohci, OHCI1394_PhyUpperBound, 0xffff0000);
|
|
}
|
|
|
|
/**
|
|
* init_ohci1394_reset_and_init_dma - init controller and enable DMA
|
|
* This initializes the given controller and enables physical DMA engine in it.
|
|
*/
|
|
static inline void __init init_ohci1394_reset_and_init_dma(struct ohci *ohci)
|
|
{
|
|
/* Start off with a soft reset, clears everything to a sane state. */
|
|
init_ohci1394_soft_reset(ohci);
|
|
|
|
/* Accessing some registers without LPS enabled may cause lock up */
|
|
reg_write(ohci, OHCI1394_HCControlSet, OHCI1394_HCControl_LPS);
|
|
|
|
/* Disable and clear interrupts */
|
|
reg_write(ohci, OHCI1394_IntEventClear, 0xffffffff);
|
|
reg_write(ohci, OHCI1394_IntMaskClear, 0xffffffff);
|
|
|
|
mdelay(50); /* Wait 50msec to make sure we have full link enabled */
|
|
|
|
init_ohci1394_initialize(ohci);
|
|
/*
|
|
* The initialization causes at least one IEEE1394 bus reset. Enabling
|
|
* physical DMA only works *after* *all* bus resets have calmed down:
|
|
*/
|
|
init_ohci1394_wait_for_busresets(ohci);
|
|
|
|
/* We had to wait and do this now if we want to debug early problems */
|
|
init_ohci1394_enable_physical_dma(ohci);
|
|
}
|
|
|
|
/**
|
|
* init_ohci1394_controller - Map the registers of the controller and init DMA
|
|
* This maps the registers of the specified controller and initializes it
|
|
*/
|
|
static inline void __init init_ohci1394_controller(int num, int slot, int func)
|
|
{
|
|
unsigned long ohci_base;
|
|
struct ohci ohci;
|
|
|
|
printk(KERN_INFO "init_ohci1394_dma: initializing OHCI-1394"
|
|
" at %02x:%02x.%x\n", num, slot, func);
|
|
|
|
ohci_base = read_pci_config(num, slot, func, PCI_BASE_ADDRESS_0+(0<<2))
|
|
& PCI_BASE_ADDRESS_MEM_MASK;
|
|
|
|
set_fixmap_nocache(FIX_OHCI1394_BASE, ohci_base);
|
|
|
|
ohci.registers = (void __iomem *)fix_to_virt(FIX_OHCI1394_BASE);
|
|
|
|
init_ohci1394_reset_and_init_dma(&ohci);
|
|
}
|
|
|
|
/**
|
|
* debug_init_ohci1394_dma - scan for OHCI1394 controllers and init DMA on them
|
|
* Scans the whole PCI space for OHCI1394 controllers and inits DMA on them
|
|
*/
|
|
void __init init_ohci1394_dma_on_all_controllers(void)
|
|
{
|
|
int num, slot, func;
|
|
u32 class;
|
|
|
|
if (!early_pci_allowed())
|
|
return;
|
|
|
|
/* Poor man's PCI discovery, the only thing we can do at early boot */
|
|
for (num = 0; num < 32; num++) {
|
|
for (slot = 0; slot < 32; slot++) {
|
|
for (func = 0; func < 8; func++) {
|
|
class = read_pci_config(num, slot, func,
|
|
PCI_CLASS_REVISION);
|
|
if (class == 0xffffffff)
|
|
continue; /* No device at this func */
|
|
|
|
if (class>>8 != PCI_CLASS_SERIAL_FIREWIRE_OHCI)
|
|
continue; /* Not an OHCI-1394 device */
|
|
|
|
init_ohci1394_controller(num, slot, func);
|
|
break; /* Assume one controller per device */
|
|
}
|
|
}
|
|
}
|
|
printk(KERN_INFO "init_ohci1394_dma: finished initializing OHCI DMA\n");
|
|
}
|
|
|
|
/**
|
|
* setup_init_ohci1394_early - enables early OHCI1394 DMA initialization
|
|
*/
|
|
static int __init setup_ohci1394_dma(char *opt)
|
|
{
|
|
if (!strcmp(opt, "early"))
|
|
init_ohci1394_dma_early = 1;
|
|
return 0;
|
|
}
|
|
|
|
/* passing ohci1394_dma=early on boot causes early OHCI1394 DMA initialization */
|
|
early_param("ohci1394_dma", setup_ohci1394_dma);
|