440 lines
17 KiB
C
440 lines
17 KiB
C
/*
|
|
*
|
|
* arch/arm/mach-u300/timer.c
|
|
*
|
|
*
|
|
* Copyright (C) 2007-2009 ST-Ericsson AB
|
|
* License terms: GNU General Public License (GPL) version 2
|
|
* Timer COH 901 328, runs the OS timer interrupt.
|
|
* Author: Linus Walleij <linus.walleij@stericsson.com>
|
|
*/
|
|
#include <linux/interrupt.h>
|
|
#include <linux/sched.h>
|
|
#include <linux/time.h>
|
|
#include <linux/timex.h>
|
|
#include <linux/clockchips.h>
|
|
#include <linux/clocksource.h>
|
|
#include <linux/types.h>
|
|
#include <linux/io.h>
|
|
#include <linux/clk.h>
|
|
#include <linux/err.h>
|
|
|
|
#include <mach/hardware.h>
|
|
|
|
/* Generic stuff */
|
|
#include <asm/sched_clock.h>
|
|
#include <asm/mach/map.h>
|
|
#include <asm/mach/time.h>
|
|
#include <asm/mach/irq.h>
|
|
|
|
/* Be able to sleep for atleast 4 seconds (usually more) */
|
|
#define APPTIMER_MIN_RANGE 4
|
|
|
|
/*
|
|
* APP side special timer registers
|
|
* This timer contains four timers which can fire an interrupt each.
|
|
* OS (operating system) timer @ 32768 Hz
|
|
* DD (device driver) timer @ 1 kHz
|
|
* GP1 (general purpose 1) timer @ 1MHz
|
|
* GP2 (general purpose 2) timer @ 1MHz
|
|
*/
|
|
|
|
/* Reset OS Timer 32bit (-/W) */
|
|
#define U300_TIMER_APP_ROST (0x0000)
|
|
#define U300_TIMER_APP_ROST_TIMER_RESET (0x00000000)
|
|
/* Enable OS Timer 32bit (-/W) */
|
|
#define U300_TIMER_APP_EOST (0x0004)
|
|
#define U300_TIMER_APP_EOST_TIMER_ENABLE (0x00000000)
|
|
/* Disable OS Timer 32bit (-/W) */
|
|
#define U300_TIMER_APP_DOST (0x0008)
|
|
#define U300_TIMER_APP_DOST_TIMER_DISABLE (0x00000000)
|
|
/* OS Timer Mode Register 32bit (-/W) */
|
|
#define U300_TIMER_APP_SOSTM (0x000c)
|
|
#define U300_TIMER_APP_SOSTM_MODE_CONTINUOUS (0x00000000)
|
|
#define U300_TIMER_APP_SOSTM_MODE_ONE_SHOT (0x00000001)
|
|
/* OS Timer Status Register 32bit (R/-) */
|
|
#define U300_TIMER_APP_OSTS (0x0010)
|
|
#define U300_TIMER_APP_OSTS_TIMER_STATE_MASK (0x0000000F)
|
|
#define U300_TIMER_APP_OSTS_TIMER_STATE_IDLE (0x00000001)
|
|
#define U300_TIMER_APP_OSTS_TIMER_STATE_ACTIVE (0x00000002)
|
|
#define U300_TIMER_APP_OSTS_ENABLE_IND (0x00000010)
|
|
#define U300_TIMER_APP_OSTS_MODE_MASK (0x00000020)
|
|
#define U300_TIMER_APP_OSTS_MODE_CONTINUOUS (0x00000000)
|
|
#define U300_TIMER_APP_OSTS_MODE_ONE_SHOT (0x00000020)
|
|
#define U300_TIMER_APP_OSTS_IRQ_ENABLED_IND (0x00000040)
|
|
#define U300_TIMER_APP_OSTS_IRQ_PENDING_IND (0x00000080)
|
|
/* OS Timer Current Count Register 32bit (R/-) */
|
|
#define U300_TIMER_APP_OSTCC (0x0014)
|
|
/* OS Timer Terminal Count Register 32bit (R/W) */
|
|
#define U300_TIMER_APP_OSTTC (0x0018)
|
|
/* OS Timer Interrupt Enable Register 32bit (-/W) */
|
|
#define U300_TIMER_APP_OSTIE (0x001c)
|
|
#define U300_TIMER_APP_OSTIE_IRQ_DISABLE (0x00000000)
|
|
#define U300_TIMER_APP_OSTIE_IRQ_ENABLE (0x00000001)
|
|
/* OS Timer Interrupt Acknowledge Register 32bit (-/W) */
|
|
#define U300_TIMER_APP_OSTIA (0x0020)
|
|
#define U300_TIMER_APP_OSTIA_IRQ_ACK (0x00000080)
|
|
|
|
/* Reset DD Timer 32bit (-/W) */
|
|
#define U300_TIMER_APP_RDDT (0x0040)
|
|
#define U300_TIMER_APP_RDDT_TIMER_RESET (0x00000000)
|
|
/* Enable DD Timer 32bit (-/W) */
|
|
#define U300_TIMER_APP_EDDT (0x0044)
|
|
#define U300_TIMER_APP_EDDT_TIMER_ENABLE (0x00000000)
|
|
/* Disable DD Timer 32bit (-/W) */
|
|
#define U300_TIMER_APP_DDDT (0x0048)
|
|
#define U300_TIMER_APP_DDDT_TIMER_DISABLE (0x00000000)
|
|
/* DD Timer Mode Register 32bit (-/W) */
|
|
#define U300_TIMER_APP_SDDTM (0x004c)
|
|
#define U300_TIMER_APP_SDDTM_MODE_CONTINUOUS (0x00000000)
|
|
#define U300_TIMER_APP_SDDTM_MODE_ONE_SHOT (0x00000001)
|
|
/* DD Timer Status Register 32bit (R/-) */
|
|
#define U300_TIMER_APP_DDTS (0x0050)
|
|
#define U300_TIMER_APP_DDTS_TIMER_STATE_MASK (0x0000000F)
|
|
#define U300_TIMER_APP_DDTS_TIMER_STATE_IDLE (0x00000001)
|
|
#define U300_TIMER_APP_DDTS_TIMER_STATE_ACTIVE (0x00000002)
|
|
#define U300_TIMER_APP_DDTS_ENABLE_IND (0x00000010)
|
|
#define U300_TIMER_APP_DDTS_MODE_MASK (0x00000020)
|
|
#define U300_TIMER_APP_DDTS_MODE_CONTINUOUS (0x00000000)
|
|
#define U300_TIMER_APP_DDTS_MODE_ONE_SHOT (0x00000020)
|
|
#define U300_TIMER_APP_DDTS_IRQ_ENABLED_IND (0x00000040)
|
|
#define U300_TIMER_APP_DDTS_IRQ_PENDING_IND (0x00000080)
|
|
/* DD Timer Current Count Register 32bit (R/-) */
|
|
#define U300_TIMER_APP_DDTCC (0x0054)
|
|
/* DD Timer Terminal Count Register 32bit (R/W) */
|
|
#define U300_TIMER_APP_DDTTC (0x0058)
|
|
/* DD Timer Interrupt Enable Register 32bit (-/W) */
|
|
#define U300_TIMER_APP_DDTIE (0x005c)
|
|
#define U300_TIMER_APP_DDTIE_IRQ_DISABLE (0x00000000)
|
|
#define U300_TIMER_APP_DDTIE_IRQ_ENABLE (0x00000001)
|
|
/* DD Timer Interrupt Acknowledge Register 32bit (-/W) */
|
|
#define U300_TIMER_APP_DDTIA (0x0060)
|
|
#define U300_TIMER_APP_DDTIA_IRQ_ACK (0x00000080)
|
|
|
|
/* Reset GP1 Timer 32bit (-/W) */
|
|
#define U300_TIMER_APP_RGPT1 (0x0080)
|
|
#define U300_TIMER_APP_RGPT1_TIMER_RESET (0x00000000)
|
|
/* Enable GP1 Timer 32bit (-/W) */
|
|
#define U300_TIMER_APP_EGPT1 (0x0084)
|
|
#define U300_TIMER_APP_EGPT1_TIMER_ENABLE (0x00000000)
|
|
/* Disable GP1 Timer 32bit (-/W) */
|
|
#define U300_TIMER_APP_DGPT1 (0x0088)
|
|
#define U300_TIMER_APP_DGPT1_TIMER_DISABLE (0x00000000)
|
|
/* GP1 Timer Mode Register 32bit (-/W) */
|
|
#define U300_TIMER_APP_SGPT1M (0x008c)
|
|
#define U300_TIMER_APP_SGPT1M_MODE_CONTINUOUS (0x00000000)
|
|
#define U300_TIMER_APP_SGPT1M_MODE_ONE_SHOT (0x00000001)
|
|
/* GP1 Timer Status Register 32bit (R/-) */
|
|
#define U300_TIMER_APP_GPT1S (0x0090)
|
|
#define U300_TIMER_APP_GPT1S_TIMER_STATE_MASK (0x0000000F)
|
|
#define U300_TIMER_APP_GPT1S_TIMER_STATE_IDLE (0x00000001)
|
|
#define U300_TIMER_APP_GPT1S_TIMER_STATE_ACTIVE (0x00000002)
|
|
#define U300_TIMER_APP_GPT1S_ENABLE_IND (0x00000010)
|
|
#define U300_TIMER_APP_GPT1S_MODE_MASK (0x00000020)
|
|
#define U300_TIMER_APP_GPT1S_MODE_CONTINUOUS (0x00000000)
|
|
#define U300_TIMER_APP_GPT1S_MODE_ONE_SHOT (0x00000020)
|
|
#define U300_TIMER_APP_GPT1S_IRQ_ENABLED_IND (0x00000040)
|
|
#define U300_TIMER_APP_GPT1S_IRQ_PENDING_IND (0x00000080)
|
|
/* GP1 Timer Current Count Register 32bit (R/-) */
|
|
#define U300_TIMER_APP_GPT1CC (0x0094)
|
|
/* GP1 Timer Terminal Count Register 32bit (R/W) */
|
|
#define U300_TIMER_APP_GPT1TC (0x0098)
|
|
/* GP1 Timer Interrupt Enable Register 32bit (-/W) */
|
|
#define U300_TIMER_APP_GPT1IE (0x009c)
|
|
#define U300_TIMER_APP_GPT1IE_IRQ_DISABLE (0x00000000)
|
|
#define U300_TIMER_APP_GPT1IE_IRQ_ENABLE (0x00000001)
|
|
/* GP1 Timer Interrupt Acknowledge Register 32bit (-/W) */
|
|
#define U300_TIMER_APP_GPT1IA (0x00a0)
|
|
#define U300_TIMER_APP_GPT1IA_IRQ_ACK (0x00000080)
|
|
|
|
/* Reset GP2 Timer 32bit (-/W) */
|
|
#define U300_TIMER_APP_RGPT2 (0x00c0)
|
|
#define U300_TIMER_APP_RGPT2_TIMER_RESET (0x00000000)
|
|
/* Enable GP2 Timer 32bit (-/W) */
|
|
#define U300_TIMER_APP_EGPT2 (0x00c4)
|
|
#define U300_TIMER_APP_EGPT2_TIMER_ENABLE (0x00000000)
|
|
/* Disable GP2 Timer 32bit (-/W) */
|
|
#define U300_TIMER_APP_DGPT2 (0x00c8)
|
|
#define U300_TIMER_APP_DGPT2_TIMER_DISABLE (0x00000000)
|
|
/* GP2 Timer Mode Register 32bit (-/W) */
|
|
#define U300_TIMER_APP_SGPT2M (0x00cc)
|
|
#define U300_TIMER_APP_SGPT2M_MODE_CONTINUOUS (0x00000000)
|
|
#define U300_TIMER_APP_SGPT2M_MODE_ONE_SHOT (0x00000001)
|
|
/* GP2 Timer Status Register 32bit (R/-) */
|
|
#define U300_TIMER_APP_GPT2S (0x00d0)
|
|
#define U300_TIMER_APP_GPT2S_TIMER_STATE_MASK (0x0000000F)
|
|
#define U300_TIMER_APP_GPT2S_TIMER_STATE_IDLE (0x00000001)
|
|
#define U300_TIMER_APP_GPT2S_TIMER_STATE_ACTIVE (0x00000002)
|
|
#define U300_TIMER_APP_GPT2S_ENABLE_IND (0x00000010)
|
|
#define U300_TIMER_APP_GPT2S_MODE_MASK (0x00000020)
|
|
#define U300_TIMER_APP_GPT2S_MODE_CONTINUOUS (0x00000000)
|
|
#define U300_TIMER_APP_GPT2S_MODE_ONE_SHOT (0x00000020)
|
|
#define U300_TIMER_APP_GPT2S_IRQ_ENABLED_IND (0x00000040)
|
|
#define U300_TIMER_APP_GPT2S_IRQ_PENDING_IND (0x00000080)
|
|
/* GP2 Timer Current Count Register 32bit (R/-) */
|
|
#define U300_TIMER_APP_GPT2CC (0x00d4)
|
|
/* GP2 Timer Terminal Count Register 32bit (R/W) */
|
|
#define U300_TIMER_APP_GPT2TC (0x00d8)
|
|
/* GP2 Timer Interrupt Enable Register 32bit (-/W) */
|
|
#define U300_TIMER_APP_GPT2IE (0x00dc)
|
|
#define U300_TIMER_APP_GPT2IE_IRQ_DISABLE (0x00000000)
|
|
#define U300_TIMER_APP_GPT2IE_IRQ_ENABLE (0x00000001)
|
|
/* GP2 Timer Interrupt Acknowledge Register 32bit (-/W) */
|
|
#define U300_TIMER_APP_GPT2IA (0x00e0)
|
|
#define U300_TIMER_APP_GPT2IA_IRQ_ACK (0x00000080)
|
|
|
|
/* Clock request control register - all four timers */
|
|
#define U300_TIMER_APP_CRC (0x100)
|
|
#define U300_TIMER_APP_CRC_CLOCK_REQUEST_ENABLE (0x00000001)
|
|
|
|
#define TICKS_PER_JIFFY ((CLOCK_TICK_RATE + (HZ/2)) / HZ)
|
|
#define US_PER_TICK ((1000000 + (HZ/2)) / HZ)
|
|
|
|
/*
|
|
* The u300_set_mode() function is always called first, if we
|
|
* have oneshot timer active, the oneshot scheduling function
|
|
* u300_set_next_event() is called immediately after.
|
|
*/
|
|
static void u300_set_mode(enum clock_event_mode mode,
|
|
struct clock_event_device *evt)
|
|
{
|
|
switch (mode) {
|
|
case CLOCK_EVT_MODE_PERIODIC:
|
|
/* Disable interrupts on GPT1 */
|
|
writel(U300_TIMER_APP_GPT1IE_IRQ_DISABLE,
|
|
U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1IE);
|
|
/* Disable GP1 while we're reprogramming it. */
|
|
writel(U300_TIMER_APP_DGPT1_TIMER_DISABLE,
|
|
U300_TIMER_APP_VBASE + U300_TIMER_APP_DGPT1);
|
|
/*
|
|
* Set the periodic mode to a certain number of ticks per
|
|
* jiffy.
|
|
*/
|
|
writel(TICKS_PER_JIFFY,
|
|
U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1TC);
|
|
/*
|
|
* Set continuous mode, so the timer keeps triggering
|
|
* interrupts.
|
|
*/
|
|
writel(U300_TIMER_APP_SGPT1M_MODE_CONTINUOUS,
|
|
U300_TIMER_APP_VBASE + U300_TIMER_APP_SGPT1M);
|
|
/* Enable timer interrupts */
|
|
writel(U300_TIMER_APP_GPT1IE_IRQ_ENABLE,
|
|
U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1IE);
|
|
/* Then enable the OS timer again */
|
|
writel(U300_TIMER_APP_EGPT1_TIMER_ENABLE,
|
|
U300_TIMER_APP_VBASE + U300_TIMER_APP_EGPT1);
|
|
break;
|
|
case CLOCK_EVT_MODE_ONESHOT:
|
|
/* Just break; here? */
|
|
/*
|
|
* The actual event will be programmed by the next event hook,
|
|
* so we just set a dummy value somewhere at the end of the
|
|
* universe here.
|
|
*/
|
|
/* Disable interrupts on GPT1 */
|
|
writel(U300_TIMER_APP_GPT1IE_IRQ_DISABLE,
|
|
U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1IE);
|
|
/* Disable GP1 while we're reprogramming it. */
|
|
writel(U300_TIMER_APP_DGPT1_TIMER_DISABLE,
|
|
U300_TIMER_APP_VBASE + U300_TIMER_APP_DGPT1);
|
|
/*
|
|
* Expire far in the future, u300_set_next_event() will be
|
|
* called soon...
|
|
*/
|
|
writel(0xFFFFFFFF, U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1TC);
|
|
/* We run one shot per tick here! */
|
|
writel(U300_TIMER_APP_SGPT1M_MODE_ONE_SHOT,
|
|
U300_TIMER_APP_VBASE + U300_TIMER_APP_SGPT1M);
|
|
/* Enable interrupts for this timer */
|
|
writel(U300_TIMER_APP_GPT1IE_IRQ_ENABLE,
|
|
U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1IE);
|
|
/* Enable timer */
|
|
writel(U300_TIMER_APP_EGPT1_TIMER_ENABLE,
|
|
U300_TIMER_APP_VBASE + U300_TIMER_APP_EGPT1);
|
|
break;
|
|
case CLOCK_EVT_MODE_UNUSED:
|
|
case CLOCK_EVT_MODE_SHUTDOWN:
|
|
/* Disable interrupts on GP1 */
|
|
writel(U300_TIMER_APP_GPT1IE_IRQ_DISABLE,
|
|
U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1IE);
|
|
/* Disable GP1 */
|
|
writel(U300_TIMER_APP_DGPT1_TIMER_DISABLE,
|
|
U300_TIMER_APP_VBASE + U300_TIMER_APP_DGPT1);
|
|
break;
|
|
case CLOCK_EVT_MODE_RESUME:
|
|
/* Ignore this call */
|
|
break;
|
|
}
|
|
}
|
|
|
|
/*
|
|
* The app timer in one shot mode obviously has to be reprogrammed
|
|
* in EXACTLY this sequence to work properly. Do NOT try to e.g. replace
|
|
* the interrupt disable + timer disable commands with a reset command,
|
|
* it will fail miserably. Apparently (and I found this the hard way)
|
|
* the timer is very sensitive to the instruction order, though you don't
|
|
* get that impression from the data sheet.
|
|
*/
|
|
static int u300_set_next_event(unsigned long cycles,
|
|
struct clock_event_device *evt)
|
|
|
|
{
|
|
/* Disable interrupts on GPT1 */
|
|
writel(U300_TIMER_APP_GPT1IE_IRQ_DISABLE,
|
|
U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1IE);
|
|
/* Disable GP1 while we're reprogramming it. */
|
|
writel(U300_TIMER_APP_DGPT1_TIMER_DISABLE,
|
|
U300_TIMER_APP_VBASE + U300_TIMER_APP_DGPT1);
|
|
/* Reset the General Purpose timer 1. */
|
|
writel(U300_TIMER_APP_RGPT1_TIMER_RESET,
|
|
U300_TIMER_APP_VBASE + U300_TIMER_APP_RGPT1);
|
|
/* IRQ in n * cycles */
|
|
writel(cycles, U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1TC);
|
|
/*
|
|
* We run one shot per tick here! (This is necessary to reconfigure,
|
|
* the timer will tilt if you don't!)
|
|
*/
|
|
writel(U300_TIMER_APP_SGPT1M_MODE_ONE_SHOT,
|
|
U300_TIMER_APP_VBASE + U300_TIMER_APP_SGPT1M);
|
|
/* Enable timer interrupts */
|
|
writel(U300_TIMER_APP_GPT1IE_IRQ_ENABLE,
|
|
U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1IE);
|
|
/* Then enable the OS timer again */
|
|
writel(U300_TIMER_APP_EGPT1_TIMER_ENABLE,
|
|
U300_TIMER_APP_VBASE + U300_TIMER_APP_EGPT1);
|
|
return 0;
|
|
}
|
|
|
|
|
|
/* Use general purpose timer 1 as clock event */
|
|
static struct clock_event_device clockevent_u300_1mhz = {
|
|
.name = "GPT1",
|
|
.rating = 300, /* Reasonably fast and accurate clock event */
|
|
.features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT,
|
|
.set_next_event = u300_set_next_event,
|
|
.set_mode = u300_set_mode,
|
|
};
|
|
|
|
/* Clock event timer interrupt handler */
|
|
static irqreturn_t u300_timer_interrupt(int irq, void *dev_id)
|
|
{
|
|
struct clock_event_device *evt = &clockevent_u300_1mhz;
|
|
/* ACK/Clear timer IRQ for the APP GPT1 Timer */
|
|
writel(U300_TIMER_APP_GPT1IA_IRQ_ACK,
|
|
U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1IA);
|
|
evt->event_handler(evt);
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static struct irqaction u300_timer_irq = {
|
|
.name = "U300 Timer Tick",
|
|
.flags = IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL,
|
|
.handler = u300_timer_interrupt,
|
|
};
|
|
|
|
/*
|
|
* Override the global weak sched_clock symbol with this
|
|
* local implementation which uses the clocksource to get some
|
|
* better resolution when scheduling the kernel. We accept that
|
|
* this wraps around for now, since it is just a relative time
|
|
* stamp. (Inspired by OMAP implementation.)
|
|
*/
|
|
static DEFINE_CLOCK_DATA(cd);
|
|
|
|
unsigned long long notrace sched_clock(void)
|
|
{
|
|
u32 cyc = readl(U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT2CC);
|
|
return cyc_to_sched_clock(&cd, cyc, (u32)~0);
|
|
}
|
|
|
|
static void notrace u300_update_sched_clock(void)
|
|
{
|
|
u32 cyc = readl(U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT2CC);
|
|
update_sched_clock(&cd, cyc, (u32)~0);
|
|
}
|
|
|
|
|
|
/*
|
|
* This sets up the system timers, clock source and clock event.
|
|
*/
|
|
static void __init u300_timer_init(void)
|
|
{
|
|
struct clk *clk;
|
|
unsigned long rate;
|
|
|
|
/* Clock the interrupt controller */
|
|
clk = clk_get_sys("apptimer", NULL);
|
|
BUG_ON(IS_ERR(clk));
|
|
clk_enable(clk);
|
|
rate = clk_get_rate(clk);
|
|
|
|
init_sched_clock(&cd, u300_update_sched_clock, 32, rate);
|
|
|
|
/*
|
|
* Disable the "OS" and "DD" timers - these are designed for Symbian!
|
|
* Example usage in cnh1601578 cpu subsystem pd_timer_app.c
|
|
*/
|
|
writel(U300_TIMER_APP_CRC_CLOCK_REQUEST_ENABLE,
|
|
U300_TIMER_APP_VBASE + U300_TIMER_APP_CRC);
|
|
writel(U300_TIMER_APP_ROST_TIMER_RESET,
|
|
U300_TIMER_APP_VBASE + U300_TIMER_APP_ROST);
|
|
writel(U300_TIMER_APP_DOST_TIMER_DISABLE,
|
|
U300_TIMER_APP_VBASE + U300_TIMER_APP_DOST);
|
|
writel(U300_TIMER_APP_RDDT_TIMER_RESET,
|
|
U300_TIMER_APP_VBASE + U300_TIMER_APP_RDDT);
|
|
writel(U300_TIMER_APP_DDDT_TIMER_DISABLE,
|
|
U300_TIMER_APP_VBASE + U300_TIMER_APP_DDDT);
|
|
|
|
/* Reset the General Purpose timer 1. */
|
|
writel(U300_TIMER_APP_RGPT1_TIMER_RESET,
|
|
U300_TIMER_APP_VBASE + U300_TIMER_APP_RGPT1);
|
|
|
|
/* Set up the IRQ handler */
|
|
setup_irq(IRQ_U300_TIMER_APP_GP1, &u300_timer_irq);
|
|
|
|
/* Reset the General Purpose timer 2 */
|
|
writel(U300_TIMER_APP_RGPT2_TIMER_RESET,
|
|
U300_TIMER_APP_VBASE + U300_TIMER_APP_RGPT2);
|
|
/* Set this timer to run around forever */
|
|
writel(0xFFFFFFFFU, U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT2TC);
|
|
/* Set continuous mode so it wraps around */
|
|
writel(U300_TIMER_APP_SGPT2M_MODE_CONTINUOUS,
|
|
U300_TIMER_APP_VBASE + U300_TIMER_APP_SGPT2M);
|
|
/* Disable timer interrupts */
|
|
writel(U300_TIMER_APP_GPT2IE_IRQ_DISABLE,
|
|
U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT2IE);
|
|
/* Then enable the GP2 timer to use as a free running us counter */
|
|
writel(U300_TIMER_APP_EGPT2_TIMER_ENABLE,
|
|
U300_TIMER_APP_VBASE + U300_TIMER_APP_EGPT2);
|
|
|
|
/* Use general purpose timer 2 as clock source */
|
|
if (clocksource_mmio_init(U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT2CC,
|
|
"GPT2", rate, 300, 32, clocksource_mmio_readl_up))
|
|
printk(KERN_ERR "timer: failed to initialize clock "
|
|
"source %s\n", clocksource_u300_1mhz.name);
|
|
|
|
clockevents_calc_mult_shift(&clockevent_u300_1mhz,
|
|
rate, APPTIMER_MIN_RANGE);
|
|
/* 32bit counter, so 32bits delta is max */
|
|
clockevent_u300_1mhz.max_delta_ns =
|
|
clockevent_delta2ns(0xffffffff, &clockevent_u300_1mhz);
|
|
/* This timer is slow enough to set for 1 cycle == 1 MHz */
|
|
clockevent_u300_1mhz.min_delta_ns =
|
|
clockevent_delta2ns(1, &clockevent_u300_1mhz);
|
|
clockevent_u300_1mhz.cpumask = cpumask_of(0);
|
|
clockevents_register_device(&clockevent_u300_1mhz);
|
|
/*
|
|
* TODO: init and register the rest of the timers too, they can be
|
|
* used by hrtimers!
|
|
*/
|
|
}
|
|
|
|
/*
|
|
* Very simple system timer that only register the clock event and
|
|
* clock source.
|
|
*/
|
|
struct sys_timer u300_timer = {
|
|
.init = u300_timer_init,
|
|
};
|