295 lines
7.2 KiB
C
295 lines
7.2 KiB
C
/*
|
|
* linux/arch/arm/mach-nomadik/board-8815nhk.c
|
|
*
|
|
* Copyright (C) STMicroelectronics
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2, as
|
|
* published by the Free Software Foundation.
|
|
*
|
|
* NHK15 board specifc driver definition
|
|
*/
|
|
#include <linux/types.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/init.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/amba/bus.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/gpio.h>
|
|
#include <linux/mtd/mtd.h>
|
|
#include <linux/mtd/nand.h>
|
|
#include <linux/mtd/onenand.h>
|
|
#include <linux/mtd/partitions.h>
|
|
#include <linux/io.h>
|
|
#include <asm/sizes.h>
|
|
#include <asm/mach-types.h>
|
|
#include <asm/mach/arch.h>
|
|
#include <asm/mach/irq.h>
|
|
#include <asm/mach/flash.h>
|
|
|
|
#include <plat/mtu.h>
|
|
|
|
#include <mach/setup.h>
|
|
#include <mach/nand.h>
|
|
#include <mach/fsmc.h>
|
|
#include "clock.h"
|
|
|
|
/* Initial value for SRC control register: all timers use MXTAL/8 source */
|
|
#define SRC_CR_INIT_MASK 0x00007fff
|
|
#define SRC_CR_INIT_VAL 0x2aaa8000
|
|
|
|
/* These addresses span 16MB, so use three individual pages */
|
|
static struct resource nhk8815_nand_resources[] = {
|
|
{
|
|
.name = "nand_addr",
|
|
.start = NAND_IO_ADDR,
|
|
.end = NAND_IO_ADDR + 0xfff,
|
|
.flags = IORESOURCE_MEM,
|
|
}, {
|
|
.name = "nand_cmd",
|
|
.start = NAND_IO_CMD,
|
|
.end = NAND_IO_CMD + 0xfff,
|
|
.flags = IORESOURCE_MEM,
|
|
}, {
|
|
.name = "nand_data",
|
|
.start = NAND_IO_DATA,
|
|
.end = NAND_IO_DATA + 0xfff,
|
|
.flags = IORESOURCE_MEM,
|
|
}
|
|
};
|
|
|
|
static int nhk8815_nand_init(void)
|
|
{
|
|
/* FSMC setup for nand chip select (8-bit nand in 8815NHK) */
|
|
writel(0x0000000E, FSMC_PCR(0));
|
|
writel(0x000D0A00, FSMC_PMEM(0));
|
|
writel(0x00100A00, FSMC_PATT(0));
|
|
|
|
/* enable access to the chip select area */
|
|
writel(readl(FSMC_PCR(0)) | 0x04, FSMC_PCR(0));
|
|
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* These partitions are the same as those used in the 2.6.20 release
|
|
* shipped by the vendor; the first two partitions are mandated
|
|
* by the boot ROM, and the bootloader area is somehow oversized...
|
|
*/
|
|
static struct mtd_partition nhk8815_partitions[] = {
|
|
{
|
|
.name = "X-Loader(NAND)",
|
|
.offset = 0,
|
|
.size = SZ_256K,
|
|
}, {
|
|
.name = "MemInit(NAND)",
|
|
.offset = MTDPART_OFS_APPEND,
|
|
.size = SZ_256K,
|
|
}, {
|
|
.name = "BootLoader(NAND)",
|
|
.offset = MTDPART_OFS_APPEND,
|
|
.size = SZ_2M,
|
|
}, {
|
|
.name = "Kernel zImage(NAND)",
|
|
.offset = MTDPART_OFS_APPEND,
|
|
.size = 3 * SZ_1M,
|
|
}, {
|
|
.name = "Root Filesystem(NAND)",
|
|
.offset = MTDPART_OFS_APPEND,
|
|
.size = 22 * SZ_1M,
|
|
}, {
|
|
.name = "User Filesystem(NAND)",
|
|
.offset = MTDPART_OFS_APPEND,
|
|
.size = MTDPART_SIZ_FULL,
|
|
}
|
|
};
|
|
|
|
static struct nomadik_nand_platform_data nhk8815_nand_data = {
|
|
.parts = nhk8815_partitions,
|
|
.nparts = ARRAY_SIZE(nhk8815_partitions),
|
|
.options = NAND_COPYBACK | NAND_CACHEPRG | NAND_NO_PADDING \
|
|
| NAND_NO_READRDY | NAND_NO_AUTOINCR,
|
|
.init = nhk8815_nand_init,
|
|
};
|
|
|
|
static struct platform_device nhk8815_nand_device = {
|
|
.name = "nomadik_nand",
|
|
.dev = {
|
|
.platform_data = &nhk8815_nand_data,
|
|
},
|
|
.resource = nhk8815_nand_resources,
|
|
.num_resources = ARRAY_SIZE(nhk8815_nand_resources),
|
|
};
|
|
|
|
/* These are the partitions for the OneNand device, different from above */
|
|
static struct mtd_partition nhk8815_onenand_partitions[] = {
|
|
{
|
|
.name = "X-Loader(OneNAND)",
|
|
.offset = 0,
|
|
.size = SZ_256K,
|
|
}, {
|
|
.name = "MemInit(OneNAND)",
|
|
.offset = MTDPART_OFS_APPEND,
|
|
.size = SZ_256K,
|
|
}, {
|
|
.name = "BootLoader(OneNAND)",
|
|
.offset = MTDPART_OFS_APPEND,
|
|
.size = SZ_2M-SZ_256K,
|
|
}, {
|
|
.name = "SysImage(OneNAND)",
|
|
.offset = MTDPART_OFS_APPEND,
|
|
.size = 4 * SZ_1M,
|
|
}, {
|
|
.name = "Root Filesystem(OneNAND)",
|
|
.offset = MTDPART_OFS_APPEND,
|
|
.size = 22 * SZ_1M,
|
|
}, {
|
|
.name = "User Filesystem(OneNAND)",
|
|
.offset = MTDPART_OFS_APPEND,
|
|
.size = MTDPART_SIZ_FULL,
|
|
}
|
|
};
|
|
|
|
static struct onenand_platform_data nhk8815_onenand_data = {
|
|
.parts = nhk8815_onenand_partitions,
|
|
.nr_parts = ARRAY_SIZE(nhk8815_onenand_partitions),
|
|
};
|
|
|
|
static struct resource nhk8815_onenand_resource[] = {
|
|
{
|
|
.start = 0x30000000,
|
|
.end = 0x30000000 + SZ_128K - 1,
|
|
.flags = IORESOURCE_MEM,
|
|
},
|
|
};
|
|
|
|
static struct platform_device nhk8815_onenand_device = {
|
|
.name = "onenand-flash",
|
|
.id = -1,
|
|
.dev = {
|
|
.platform_data = &nhk8815_onenand_data,
|
|
},
|
|
.resource = nhk8815_onenand_resource,
|
|
.num_resources = ARRAY_SIZE(nhk8815_onenand_resource),
|
|
};
|
|
|
|
static void __init nhk8815_onenand_init(void)
|
|
{
|
|
#ifdef CONFIG_MTD_ONENAND
|
|
/* Set up SMCS0 for OneNand */
|
|
writel(0x000030db, FSMC_BCR(0));
|
|
writel(0x02100551, FSMC_BTR(0));
|
|
#endif
|
|
}
|
|
|
|
#define __MEM_4K_RESOURCE(x) \
|
|
.res = {.start = (x), .end = (x) + SZ_4K - 1, .flags = IORESOURCE_MEM}
|
|
|
|
static struct amba_device uart0_device = {
|
|
.dev = { .init_name = "uart0" },
|
|
__MEM_4K_RESOURCE(NOMADIK_UART0_BASE),
|
|
.irq = {IRQ_UART0, NO_IRQ},
|
|
};
|
|
|
|
static struct amba_device uart1_device = {
|
|
.dev = { .init_name = "uart1" },
|
|
__MEM_4K_RESOURCE(NOMADIK_UART1_BASE),
|
|
.irq = {IRQ_UART1, NO_IRQ},
|
|
};
|
|
|
|
static struct amba_device *amba_devs[] __initdata = {
|
|
&uart0_device,
|
|
&uart1_device,
|
|
};
|
|
|
|
/* We have a fixed clock alone, by now */
|
|
static struct clk nhk8815_clk_48 = {
|
|
.rate = 48*1000*1000,
|
|
};
|
|
|
|
static struct resource nhk8815_eth_resources[] = {
|
|
{
|
|
.name = "smc91x-regs",
|
|
.start = 0x34000000 + 0x300,
|
|
.end = 0x34000000 + SZ_64K - 1,
|
|
.flags = IORESOURCE_MEM,
|
|
}, {
|
|
.start = NOMADIK_GPIO_TO_IRQ(115),
|
|
.end = NOMADIK_GPIO_TO_IRQ(115),
|
|
.flags = IORESOURCE_IRQ | IRQF_TRIGGER_RISING,
|
|
}
|
|
};
|
|
|
|
static struct platform_device nhk8815_eth_device = {
|
|
.name = "smc91x",
|
|
.resource = nhk8815_eth_resources,
|
|
.num_resources = ARRAY_SIZE(nhk8815_eth_resources),
|
|
};
|
|
|
|
static int __init nhk8815_eth_init(void)
|
|
{
|
|
int gpio_nr = 115; /* hardwired in the board */
|
|
int err;
|
|
|
|
err = gpio_request(gpio_nr, "eth_irq");
|
|
if (!err) err = nmk_gpio_set_mode(gpio_nr, NMK_GPIO_ALT_GPIO);
|
|
if (!err) err = gpio_direction_input(gpio_nr);
|
|
if (err)
|
|
pr_err("Error %i in %s\n", err, __func__);
|
|
return err;
|
|
}
|
|
device_initcall(nhk8815_eth_init);
|
|
|
|
static struct platform_device *nhk8815_platform_devices[] __initdata = {
|
|
&nhk8815_nand_device,
|
|
&nhk8815_onenand_device,
|
|
&nhk8815_eth_device,
|
|
/* will add more devices */
|
|
};
|
|
|
|
static void __init nomadik_timer_init(void)
|
|
{
|
|
u32 src_cr;
|
|
|
|
/* Configure timer sources in "system reset controller" ctrl reg */
|
|
src_cr = readl(io_p2v(NOMADIK_SRC_BASE));
|
|
src_cr &= SRC_CR_INIT_MASK;
|
|
src_cr |= SRC_CR_INIT_VAL;
|
|
writel(src_cr, io_p2v(NOMADIK_SRC_BASE));
|
|
|
|
/* Save global pointer to mtu, used by platform timer code */
|
|
mtu_base = io_p2v(NOMADIK_MTU0_BASE);
|
|
|
|
nmdk_timer_init();
|
|
}
|
|
|
|
static struct sys_timer nomadik_timer = {
|
|
.init = nomadik_timer_init,
|
|
};
|
|
|
|
static void __init nhk8815_platform_init(void)
|
|
{
|
|
int i;
|
|
|
|
cpu8815_platform_init();
|
|
nhk8815_onenand_init();
|
|
platform_add_devices(nhk8815_platform_devices,
|
|
ARRAY_SIZE(nhk8815_platform_devices));
|
|
|
|
for (i = 0; i < ARRAY_SIZE(amba_devs); i++) {
|
|
nmdk_clk_create(&nhk8815_clk_48, amba_devs[i]->dev.init_name);
|
|
amba_device_register(amba_devs[i], &iomem_resource);
|
|
}
|
|
}
|
|
|
|
MACHINE_START(NOMADIK, "NHK8815")
|
|
/* Maintainer: ST MicroElectronics */
|
|
.phys_io = NOMADIK_UART0_BASE,
|
|
.io_pg_offst = (IO_ADDRESS(NOMADIK_UART0_BASE) >> 18) & 0xfffc,
|
|
.boot_params = 0x100,
|
|
.map_io = cpu8815_map_io,
|
|
.init_irq = cpu8815_init_irq,
|
|
.timer = &nomadik_timer,
|
|
.init_machine = nhk8815_platform_init,
|
|
MACHINE_END
|