Don't reserve size for bad blocks when checking image size

When checking *.img size with the partition size, the build system
reserves additional bits for spare bits and spare bad blocks.

However, for emmc and ufs, the space bits and blocks are entirely
managed by the underlying controller and thus not visible from outside
of the controller. In fact the check routine was made for legacy MTD
storages where raw flash blocks are directly exposed.

This makes the size checking a little bit conservative in modern devices.
Builds were failed even though the *.img can actually fit into the
partition. To handle this problem, the additional size is no longer
reserved when checking *.img size with the partition size.

This change also removes following build flags that are meaningful
only for devices having MTD storages:
BOARD_NAND_PAGE_SIZE
BOARD_NAND_SPARE_SIZE
Further use of them breaks the build

Bug: 35790399
Bug: 66399382
Test: build

Merged-In: I954bf261441b53844e75d05788866f1692a2ad43
Change-Id: I954bf261441b53844e75d05788866f1692a2ad43

core/Makefile

@@ -1310,12 +1310,12 @@ endif
 .PHONY: recoveryimage
 recoveryimage: $(INSTALLED_RECOVERYIMAGE_TARGET) $(RECOVERY_RESOURCE_ZIP)
 
-ifeq ($(BOARD_NAND_PAGE_SIZE),)
-BOARD_NAND_PAGE_SIZE := 2048
+ifneq ($(BOARD_NAND_PAGE_SIZE),)
+$(error MTD device is no longer supported and thus BOARD_NAND_PAGE_SIZE is deprecated.)
 endif
 
-ifeq ($(BOARD_NAND_SPARE_SIZE),)
-BOARD_NAND_SPARE_SIZE := 64
+ifneq ($(BOARD_NAND_SPARE_SIZE),)
+$(error MTD device is no longer supported and thus BOARD_NAND_SPARE_SIZE is deprecated.)
 endif
 
 # -----------------------------------------------------------------

core/definitions.mk

@@ -2754,39 +2754,16 @@ ifndef get-file-size
 $(error HOST_OS must define get-file-size)
 endif
 
-# Convert a partition data size (eg, as reported in /proc/mtd) to the
-# size of the image used to flash that partition (which includes a
-# spare area for each page).
-# $(1): the partition data size
-define image-size-from-data-size
-$(strip $(eval _isfds_value := $$(shell echo $$$$(($(1) / $(BOARD_NAND_PAGE_SIZE) * \
-  ($(BOARD_NAND_PAGE_SIZE)+$(BOARD_NAND_SPARE_SIZE))))))\
-$(if $(filter 0, $(_isfds_value)),$(shell echo $$(($(BOARD_NAND_PAGE_SIZE)+$(BOARD_NAND_SPARE_SIZE)))),$(_isfds_value))\
-$(eval _isfds_value :=))
-endef
-
 # $(1): The file(s) to check (often $@)
-# $(2): The maximum total image size, in decimal bytes.
-#    Make sure to take into account any reserved space needed for the FS.
-#
-# If $(2) is empty, evaluates to "true"
-#
-# Reserve bad blocks.  Make sure that MAX(1% of partition size, 2 blocks)
-# is left over after the image has been flashed.  Round the 1% up to the
-# next whole flash block size.
-define assert-max-file-size
+# $(2): The partition size.
+define assert-max-image-size
 $(if $(2), \
   size=$$(for i in $(1); do $(call get-file-size,$$i); echo +; done; echo 0); \
   total=$$(( $$( echo "$$size" ) )); \
   printname=$$(echo -n "$(1)" | tr " " +); \
-  img_blocksize=$(call image-size-from-data-size,$(BOARD_FLASH_BLOCK_SIZE)); \
-  twoblocks=$$((img_blocksize * 2)); \
-  onepct=$$((((($(2) / 100) - 1) / img_blocksize + 1) * img_blocksize)); \
-  reserve=$$((twoblocks > onepct ? twoblocks : onepct)); \
-  maxsize=$$(($(2) - reserve)); \
-  echo "$$printname maxsize=$$maxsize blocksize=$$img_blocksize total=$$total reserve=$$reserve"; \
+  maxsize=$(2); \
   if [ "$$total" -gt "$$maxsize" ]; then \
-    echo "error: $$printname too large ($$total > [$(2) - $$reserve])"; \
+    echo "error: $$printname too large ($$total > $$maxsize)"; \
     false; \
   elif [ "$$total" -gt $$((maxsize - 32768)) ]; then \
     echo "WARNING: $$printname approaching size limit ($$total now; limit $$maxsize)"; \
@@ -2796,17 +2773,6 @@ $(if $(2), \
  )
 endef
 
-# Like assert-max-file-size, but the second argument is a partition
-# size, which we'll convert to a max image size before checking it
-# against the files.
-#
-# $(1): The file(s) to check (often $@)
-# $(2): The partition size.
-define assert-max-image-size
-$(if $(2), \
-  $(call assert-max-file-size,$(1),$(call image-size-from-data-size,$(2))))
-endef
-
 
 ###########################################################
 ## Define device-specific radio files

target/board/treble_common.mk

@@ -54,8 +54,6 @@ TARGET_USES_HWC2 := true
 # Set emulator framebuffer display device buffer count to 3
 NUM_FRAMEBUFFER_SURFACE_BUFFERS := 3
 
-# TODO(b/35790399): remove when b/35790399 is fixed.
-BOARD_NAND_SPARE_SIZE := 0
 BOARD_FLASH_BLOCK_SIZE := 512
 
 # b/64700195: add minimum support for odm.img