linux/drivers/net/wireless/ath/ath9k/ar9002_hw.c

583 lines
18 KiB
C
Raw Normal View History

/*
* Copyright (c) 2008-2010 Atheros Communications Inc.
*
* Permission to use, copy, modify, and/or distribute this software for any
* purpose with or without fee is hereby granted, provided that the above
* copyright notice and this permission notice appear in all copies.
*
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
*/
#include "hw.h"
#include "ar5008_initvals.h"
#include "ar9001_initvals.h"
#include "ar9002_initvals.h"
#include "ar9002_phy.h"
ath9k: add new ANI implementation for AR9003 This adds support for ANI for AR9003. The implementation for ANI for AR9003 is slightly different than the one used for the older chipset families. It can technically be used for the older families as well but this is not yet fully tested so we only enable the new ANI for the AR5008, AR9001 and AR9002 families with a module parameter, force_new_ani. The old ANI implementation is left intact. Details of the new ANI implemention: * ANI adjustment logic is now table driven so that each ANI level setting is parameterized. This makes adjustments much more deterministic than the old procedure based logic and allows adjustments to be made incrementally to several parameters per level. * ANI register settings are now relative to INI values; so ANI param zero level == INI value. Appropriate floor and ceiling values are obeyed when adjustments are combined with INI values. * ANI processing is done once per second rather that every 100ms. The poll interval is now a set upon hardware initialization and can be picked up by the core driver. * OFDM error and CCK error processing are made in a round robin fashion rather than allowing all OFDM adjustments to be made before CCK adjustments. * ANI adjusts MRC CCK off in the presence of high CCK errors * When adjusting spur immunity (SI) and OFDM weak signal detection, ANI now sets register values for the extension channel too * When adjusting FIR step (ST), ANI now sets register for FIR step low too * FIR step adjustments now allow for an extra level of immunity for extremely noisy environments * The old Noise immunity setting (NI), which changes coarse low, size desired, etc have been removed. Changing these settings could affect up RIFS RX as well. * CCK weak signal adjustment is no longer used * ANI no longer enables phy error interrupts; in all cases phy hw counting registers are used instead * The phy error count (overflow) interrupts are also no longer used for ANI adjustments. All ANI adjustments are made via the polling routine and no adjustments are possible in the ISR context anymore * A history settings buffer is now correctly used for each channel; channel settings are initialized with the defaults but later changes are restored when returning back to that channel * When scanning, ANI is disabled settings are returned to (INI) defaults. * OFDM phy error thresholds are now 400 & 1000 (errors/second units) for low/high water marks, providing increased stability/hysteresis when changing levels. * Similarly CCK phy error thresholds are now 300 & 600 (errors/second) Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-12 12:33:45 +08:00
int modparam_force_new_ani;
module_param_named(force_new_ani, modparam_force_new_ani, int, 0444);
MODULE_PARM_DESC(nohwcrypt, "Force new ANI for AR5008, AR9001, AR9002");
/* General hardware code for the A5008/AR9001/AR9002 hadware families */
static bool ar9002_hw_macversion_supported(u32 macversion)
{
switch (macversion) {
case AR_SREV_VERSION_5416_PCI:
case AR_SREV_VERSION_5416_PCIE:
case AR_SREV_VERSION_9160:
case AR_SREV_VERSION_9100:
case AR_SREV_VERSION_9280:
case AR_SREV_VERSION_9285:
case AR_SREV_VERSION_9287:
case AR_SREV_VERSION_9271:
return true;
default:
break;
}
return false;
}
static void ar9002_hw_init_mode_regs(struct ath_hw *ah)
{
if (AR_SREV_9271(ah)) {
INIT_INI_ARRAY(&ah->iniModes, ar9271Modes_9271,
ARRAY_SIZE(ar9271Modes_9271), 6);
INIT_INI_ARRAY(&ah->iniCommon, ar9271Common_9271,
ARRAY_SIZE(ar9271Common_9271), 2);
INIT_INI_ARRAY(&ah->iniCommon_normal_cck_fir_coeff_9271,
ar9271Common_normal_cck_fir_coeff_9271,
ARRAY_SIZE(ar9271Common_normal_cck_fir_coeff_9271), 2);
INIT_INI_ARRAY(&ah->iniCommon_japan_2484_cck_fir_coeff_9271,
ar9271Common_japan_2484_cck_fir_coeff_9271,
ARRAY_SIZE(ar9271Common_japan_2484_cck_fir_coeff_9271), 2);
INIT_INI_ARRAY(&ah->iniModes_9271_1_0_only,
ar9271Modes_9271_1_0_only,
ARRAY_SIZE(ar9271Modes_9271_1_0_only), 6);
INIT_INI_ARRAY(&ah->iniModes_9271_ANI_reg, ar9271Modes_9271_ANI_reg,
ARRAY_SIZE(ar9271Modes_9271_ANI_reg), 6);
INIT_INI_ARRAY(&ah->iniModes_high_power_tx_gain_9271,
ar9271Modes_high_power_tx_gain_9271,
ARRAY_SIZE(ar9271Modes_high_power_tx_gain_9271), 6);
INIT_INI_ARRAY(&ah->iniModes_normal_power_tx_gain_9271,
ar9271Modes_normal_power_tx_gain_9271,
ARRAY_SIZE(ar9271Modes_normal_power_tx_gain_9271), 6);
return;
}
if (AR_SREV_9287_11_OR_LATER(ah)) {
INIT_INI_ARRAY(&ah->iniModes, ar9287Modes_9287_1_1,
ARRAY_SIZE(ar9287Modes_9287_1_1), 6);
INIT_INI_ARRAY(&ah->iniCommon, ar9287Common_9287_1_1,
ARRAY_SIZE(ar9287Common_9287_1_1), 2);
if (ah->config.pcie_clock_req)
INIT_INI_ARRAY(&ah->iniPcieSerdes,
ar9287PciePhy_clkreq_off_L1_9287_1_1,
ARRAY_SIZE(ar9287PciePhy_clkreq_off_L1_9287_1_1), 2);
else
INIT_INI_ARRAY(&ah->iniPcieSerdes,
ar9287PciePhy_clkreq_always_on_L1_9287_1_1,
ARRAY_SIZE(ar9287PciePhy_clkreq_always_on_L1_9287_1_1),
2);
} else if (AR_SREV_9285_12_OR_LATER(ah)) {
INIT_INI_ARRAY(&ah->iniModes, ar9285Modes_9285_1_2,
ARRAY_SIZE(ar9285Modes_9285_1_2), 6);
INIT_INI_ARRAY(&ah->iniCommon, ar9285Common_9285_1_2,
ARRAY_SIZE(ar9285Common_9285_1_2), 2);
if (ah->config.pcie_clock_req) {
INIT_INI_ARRAY(&ah->iniPcieSerdes,
ar9285PciePhy_clkreq_off_L1_9285_1_2,
ARRAY_SIZE(ar9285PciePhy_clkreq_off_L1_9285_1_2), 2);
} else {
INIT_INI_ARRAY(&ah->iniPcieSerdes,
ar9285PciePhy_clkreq_always_on_L1_9285_1_2,
ARRAY_SIZE(ar9285PciePhy_clkreq_always_on_L1_9285_1_2),
2);
}
} else if (AR_SREV_9280_20_OR_LATER(ah)) {
INIT_INI_ARRAY(&ah->iniModes, ar9280Modes_9280_2,
ARRAY_SIZE(ar9280Modes_9280_2), 6);
INIT_INI_ARRAY(&ah->iniCommon, ar9280Common_9280_2,
ARRAY_SIZE(ar9280Common_9280_2), 2);
if (ah->config.pcie_clock_req) {
INIT_INI_ARRAY(&ah->iniPcieSerdes,
ar9280PciePhy_clkreq_off_L1_9280,
ARRAY_SIZE(ar9280PciePhy_clkreq_off_L1_9280), 2);
} else {
INIT_INI_ARRAY(&ah->iniPcieSerdes,
ar9280PciePhy_clkreq_always_on_L1_9280,
ARRAY_SIZE(ar9280PciePhy_clkreq_always_on_L1_9280), 2);
}
INIT_INI_ARRAY(&ah->iniModesAdditional,
ar9280Modes_fast_clock_9280_2,
ARRAY_SIZE(ar9280Modes_fast_clock_9280_2), 3);
} else if (AR_SREV_9160_10_OR_LATER(ah)) {
INIT_INI_ARRAY(&ah->iniModes, ar5416Modes_9160,
ARRAY_SIZE(ar5416Modes_9160), 6);
INIT_INI_ARRAY(&ah->iniCommon, ar5416Common_9160,
ARRAY_SIZE(ar5416Common_9160), 2);
INIT_INI_ARRAY(&ah->iniBank0, ar5416Bank0_9160,
ARRAY_SIZE(ar5416Bank0_9160), 2);
INIT_INI_ARRAY(&ah->iniBB_RfGain, ar5416BB_RfGain_9160,
ARRAY_SIZE(ar5416BB_RfGain_9160), 3);
INIT_INI_ARRAY(&ah->iniBank1, ar5416Bank1_9160,
ARRAY_SIZE(ar5416Bank1_9160), 2);
INIT_INI_ARRAY(&ah->iniBank2, ar5416Bank2_9160,
ARRAY_SIZE(ar5416Bank2_9160), 2);
INIT_INI_ARRAY(&ah->iniBank3, ar5416Bank3_9160,
ARRAY_SIZE(ar5416Bank3_9160), 3);
INIT_INI_ARRAY(&ah->iniBank6, ar5416Bank6_9160,
ARRAY_SIZE(ar5416Bank6_9160), 3);
INIT_INI_ARRAY(&ah->iniBank6TPC, ar5416Bank6TPC_9160,
ARRAY_SIZE(ar5416Bank6TPC_9160), 3);
INIT_INI_ARRAY(&ah->iniBank7, ar5416Bank7_9160,
ARRAY_SIZE(ar5416Bank7_9160), 2);
if (AR_SREV_9160_11(ah)) {
INIT_INI_ARRAY(&ah->iniAddac,
ar5416Addac_9160_1_1,
ARRAY_SIZE(ar5416Addac_9160_1_1), 2);
} else {
INIT_INI_ARRAY(&ah->iniAddac, ar5416Addac_9160,
ARRAY_SIZE(ar5416Addac_9160), 2);
}
} else if (AR_SREV_9100_OR_LATER(ah)) {
INIT_INI_ARRAY(&ah->iniModes, ar5416Modes_9100,
ARRAY_SIZE(ar5416Modes_9100), 6);
INIT_INI_ARRAY(&ah->iniCommon, ar5416Common_9100,
ARRAY_SIZE(ar5416Common_9100), 2);
INIT_INI_ARRAY(&ah->iniBank0, ar5416Bank0_9100,
ARRAY_SIZE(ar5416Bank0_9100), 2);
INIT_INI_ARRAY(&ah->iniBB_RfGain, ar5416BB_RfGain_9100,
ARRAY_SIZE(ar5416BB_RfGain_9100), 3);
INIT_INI_ARRAY(&ah->iniBank1, ar5416Bank1_9100,
ARRAY_SIZE(ar5416Bank1_9100), 2);
INIT_INI_ARRAY(&ah->iniBank2, ar5416Bank2_9100,
ARRAY_SIZE(ar5416Bank2_9100), 2);
INIT_INI_ARRAY(&ah->iniBank3, ar5416Bank3_9100,
ARRAY_SIZE(ar5416Bank3_9100), 3);
INIT_INI_ARRAY(&ah->iniBank6, ar5416Bank6_9100,
ARRAY_SIZE(ar5416Bank6_9100), 3);
INIT_INI_ARRAY(&ah->iniBank6TPC, ar5416Bank6TPC_9100,
ARRAY_SIZE(ar5416Bank6TPC_9100), 3);
INIT_INI_ARRAY(&ah->iniBank7, ar5416Bank7_9100,
ARRAY_SIZE(ar5416Bank7_9100), 2);
INIT_INI_ARRAY(&ah->iniAddac, ar5416Addac_9100,
ARRAY_SIZE(ar5416Addac_9100), 2);
} else {
INIT_INI_ARRAY(&ah->iniModes, ar5416Modes,
ARRAY_SIZE(ar5416Modes), 6);
INIT_INI_ARRAY(&ah->iniCommon, ar5416Common,
ARRAY_SIZE(ar5416Common), 2);
INIT_INI_ARRAY(&ah->iniBank0, ar5416Bank0,
ARRAY_SIZE(ar5416Bank0), 2);
INIT_INI_ARRAY(&ah->iniBB_RfGain, ar5416BB_RfGain,
ARRAY_SIZE(ar5416BB_RfGain), 3);
INIT_INI_ARRAY(&ah->iniBank1, ar5416Bank1,
ARRAY_SIZE(ar5416Bank1), 2);
INIT_INI_ARRAY(&ah->iniBank2, ar5416Bank2,
ARRAY_SIZE(ar5416Bank2), 2);
INIT_INI_ARRAY(&ah->iniBank3, ar5416Bank3,
ARRAY_SIZE(ar5416Bank3), 3);
INIT_INI_ARRAY(&ah->iniBank6, ar5416Bank6,
ARRAY_SIZE(ar5416Bank6), 3);
INIT_INI_ARRAY(&ah->iniBank6TPC, ar5416Bank6TPC,
ARRAY_SIZE(ar5416Bank6TPC), 3);
INIT_INI_ARRAY(&ah->iniBank7, ar5416Bank7,
ARRAY_SIZE(ar5416Bank7), 2);
INIT_INI_ARRAY(&ah->iniAddac, ar5416Addac,
ARRAY_SIZE(ar5416Addac), 2);
}
}
/* Support for Japan ch.14 (2484) spread */
void ar9002_hw_cck_chan14_spread(struct ath_hw *ah)
{
if (AR_SREV_9287_11_OR_LATER(ah)) {
INIT_INI_ARRAY(&ah->iniCckfirNormal,
ar9287Common_normal_cck_fir_coeff_9287_1_1,
ARRAY_SIZE(ar9287Common_normal_cck_fir_coeff_9287_1_1),
2);
INIT_INI_ARRAY(&ah->iniCckfirJapan2484,
ar9287Common_japan_2484_cck_fir_coeff_9287_1_1,
ARRAY_SIZE(ar9287Common_japan_2484_cck_fir_coeff_9287_1_1),
2);
}
}
static void ar9280_20_hw_init_rxgain_ini(struct ath_hw *ah)
{
u32 rxgain_type;
if (ah->eep_ops->get_eeprom(ah, EEP_MINOR_REV) >=
AR5416_EEP_MINOR_VER_17) {
rxgain_type = ah->eep_ops->get_eeprom(ah, EEP_RXGAIN_TYPE);
if (rxgain_type == AR5416_EEP_RXGAIN_13DB_BACKOFF)
INIT_INI_ARRAY(&ah->iniModesRxGain,
ar9280Modes_backoff_13db_rxgain_9280_2,
ARRAY_SIZE(ar9280Modes_backoff_13db_rxgain_9280_2), 6);
else if (rxgain_type == AR5416_EEP_RXGAIN_23DB_BACKOFF)
INIT_INI_ARRAY(&ah->iniModesRxGain,
ar9280Modes_backoff_23db_rxgain_9280_2,
ARRAY_SIZE(ar9280Modes_backoff_23db_rxgain_9280_2), 6);
else
INIT_INI_ARRAY(&ah->iniModesRxGain,
ar9280Modes_original_rxgain_9280_2,
ARRAY_SIZE(ar9280Modes_original_rxgain_9280_2), 6);
} else {
INIT_INI_ARRAY(&ah->iniModesRxGain,
ar9280Modes_original_rxgain_9280_2,
ARRAY_SIZE(ar9280Modes_original_rxgain_9280_2), 6);
}
}
static void ar9280_20_hw_init_txgain_ini(struct ath_hw *ah)
{
u32 txgain_type;
if (ah->eep_ops->get_eeprom(ah, EEP_MINOR_REV) >=
AR5416_EEP_MINOR_VER_19) {
txgain_type = ah->eep_ops->get_eeprom(ah, EEP_TXGAIN_TYPE);
if (txgain_type == AR5416_EEP_TXGAIN_HIGH_POWER)
INIT_INI_ARRAY(&ah->iniModesTxGain,
ar9280Modes_high_power_tx_gain_9280_2,
ARRAY_SIZE(ar9280Modes_high_power_tx_gain_9280_2), 6);
else
INIT_INI_ARRAY(&ah->iniModesTxGain,
ar9280Modes_original_tx_gain_9280_2,
ARRAY_SIZE(ar9280Modes_original_tx_gain_9280_2), 6);
} else {
INIT_INI_ARRAY(&ah->iniModesTxGain,
ar9280Modes_original_tx_gain_9280_2,
ARRAY_SIZE(ar9280Modes_original_tx_gain_9280_2), 6);
}
}
static void ar9002_hw_init_mode_gain_regs(struct ath_hw *ah)
{
if (AR_SREV_9287_11_OR_LATER(ah))
INIT_INI_ARRAY(&ah->iniModesRxGain,
ar9287Modes_rx_gain_9287_1_1,
ARRAY_SIZE(ar9287Modes_rx_gain_9287_1_1), 6);
else if (AR_SREV_9280_20(ah))
ar9280_20_hw_init_rxgain_ini(ah);
if (AR_SREV_9287_11_OR_LATER(ah)) {
INIT_INI_ARRAY(&ah->iniModesTxGain,
ar9287Modes_tx_gain_9287_1_1,
ARRAY_SIZE(ar9287Modes_tx_gain_9287_1_1), 6);
} else if (AR_SREV_9280_20(ah)) {
ar9280_20_hw_init_txgain_ini(ah);
} else if (AR_SREV_9285_12_OR_LATER(ah)) {
u32 txgain_type = ah->eep_ops->get_eeprom(ah, EEP_TXGAIN_TYPE);
/* txgain table */
if (txgain_type == AR5416_EEP_TXGAIN_HIGH_POWER) {
if (AR_SREV_9285E_20(ah)) {
INIT_INI_ARRAY(&ah->iniModesTxGain,
ar9285Modes_XE2_0_high_power,
ARRAY_SIZE(
ar9285Modes_XE2_0_high_power), 6);
} else {
INIT_INI_ARRAY(&ah->iniModesTxGain,
ar9285Modes_high_power_tx_gain_9285_1_2,
ARRAY_SIZE(
ar9285Modes_high_power_tx_gain_9285_1_2), 6);
}
} else {
if (AR_SREV_9285E_20(ah)) {
INIT_INI_ARRAY(&ah->iniModesTxGain,
ar9285Modes_XE2_0_normal_power,
ARRAY_SIZE(
ar9285Modes_XE2_0_normal_power), 6);
} else {
INIT_INI_ARRAY(&ah->iniModesTxGain,
ar9285Modes_original_tx_gain_9285_1_2,
ARRAY_SIZE(
ar9285Modes_original_tx_gain_9285_1_2), 6);
}
}
}
}
/*
* Helper for ASPM support.
*
* Disable PLL when in L0s as well as receiver clock when in L1.
* This power saving option must be enabled through the SerDes.
*
* Programming the SerDes must go through the same 288 bit serial shift
* register as the other analog registers. Hence the 9 writes.
*/
static void ar9002_hw_configpcipowersave(struct ath_hw *ah,
int restore,
int power_off)
{
u8 i;
u32 val;
if (ah->is_pciexpress != true)
return;
/* Do not touch SerDes registers */
if (ah->config.pcie_powersave_enable == 2)
return;
/* Nothing to do on restore for 11N */
if (!restore) {
if (AR_SREV_9280_20_OR_LATER(ah)) {
/*
* AR9280 2.0 or later chips use SerDes values from the
* initvals.h initialized depending on chipset during
* __ath9k_hw_init()
*/
for (i = 0; i < ah->iniPcieSerdes.ia_rows; i++) {
REG_WRITE(ah, INI_RA(&ah->iniPcieSerdes, i, 0),
INI_RA(&ah->iniPcieSerdes, i, 1));
}
} else {
ENABLE_REGWRITE_BUFFER(ah);
REG_WRITE(ah, AR_PCIE_SERDES, 0x9248fc00);
REG_WRITE(ah, AR_PCIE_SERDES, 0x24924924);
/* RX shut off when elecidle is asserted */
REG_WRITE(ah, AR_PCIE_SERDES, 0x28000039);
REG_WRITE(ah, AR_PCIE_SERDES, 0x53160824);
REG_WRITE(ah, AR_PCIE_SERDES, 0xe5980579);
/*
* Ignore ah->ah_config.pcie_clock_req setting for
* pre-AR9280 11n
*/
REG_WRITE(ah, AR_PCIE_SERDES, 0x001defff);
REG_WRITE(ah, AR_PCIE_SERDES, 0x1aaabe40);
REG_WRITE(ah, AR_PCIE_SERDES, 0xbe105554);
REG_WRITE(ah, AR_PCIE_SERDES, 0x000e3007);
/* Load the new settings */
REG_WRITE(ah, AR_PCIE_SERDES2, 0x00000000);
REGWRITE_BUFFER_FLUSH(ah);
DISABLE_REGWRITE_BUFFER(ah);
}
udelay(1000);
}
if (power_off) {
/* clear bit 19 to disable L1 */
REG_CLR_BIT(ah, AR_PCIE_PM_CTRL, AR_PCIE_PM_CTRL_ENA);
val = REG_READ(ah, AR_WA);
/*
* Set PCIe workaround bits
* In AR9280 and AR9285, bit 14 in WA register (disable L1)
* should only be set when device enters D3 and be
* cleared when device comes back to D0.
*/
if (ah->config.pcie_waen) {
if (ah->config.pcie_waen & AR_WA_D3_L1_DISABLE)
val |= AR_WA_D3_L1_DISABLE;
} else {
if (((AR_SREV_9285(ah) ||
AR_SREV_9271(ah) ||
AR_SREV_9287(ah)) &&
(AR9285_WA_DEFAULT & AR_WA_D3_L1_DISABLE)) ||
(AR_SREV_9280(ah) &&
(AR9280_WA_DEFAULT & AR_WA_D3_L1_DISABLE))) {
val |= AR_WA_D3_L1_DISABLE;
}
}
if (AR_SREV_9280(ah) || AR_SREV_9285(ah) || AR_SREV_9287(ah)) {
/*
* Disable bit 6 and 7 before entering D3 to
* prevent system hang.
*/
val &= ~(AR_WA_BIT6 | AR_WA_BIT7);
}
if (AR_SREV_9285E_20(ah))
val |= AR_WA_BIT23;
REG_WRITE(ah, AR_WA, val);
} else {
if (ah->config.pcie_waen) {
val = ah->config.pcie_waen;
if (!power_off)
val &= (~AR_WA_D3_L1_DISABLE);
} else {
if (AR_SREV_9285(ah) ||
AR_SREV_9271(ah) ||
AR_SREV_9287(ah)) {
val = AR9285_WA_DEFAULT;
if (!power_off)
val &= (~AR_WA_D3_L1_DISABLE);
}
else if (AR_SREV_9280(ah)) {
/*
* For AR9280 chips, bit 22 of 0x4004
* needs to be set.
*/
val = AR9280_WA_DEFAULT;
if (!power_off)
val &= (~AR_WA_D3_L1_DISABLE);
} else {
val = AR_WA_DEFAULT;
}
}
/* WAR for ASPM system hang */
if (AR_SREV_9280(ah) || AR_SREV_9285(ah) || AR_SREV_9287(ah)) {
val |= (AR_WA_BIT6 | AR_WA_BIT7);
}
if (AR_SREV_9285E_20(ah))
val |= AR_WA_BIT23;
REG_WRITE(ah, AR_WA, val);
/* set bit 19 to allow forcing of pcie core into L1 state */
REG_SET_BIT(ah, AR_PCIE_PM_CTRL, AR_PCIE_PM_CTRL_ENA);
}
}
static int ar9002_hw_get_radiorev(struct ath_hw *ah)
{
u32 val;
int i;
ENABLE_REGWRITE_BUFFER(ah);
REG_WRITE(ah, AR_PHY(0x36), 0x00007058);
for (i = 0; i < 8; i++)
REG_WRITE(ah, AR_PHY(0x20), 0x00010000);
REGWRITE_BUFFER_FLUSH(ah);
DISABLE_REGWRITE_BUFFER(ah);
val = (REG_READ(ah, AR_PHY(256)) >> 24) & 0xff;
val = ((val & 0xf0) >> 4) | ((val & 0x0f) << 4);
return ath9k_hw_reverse_bits(val, 8);
}
int ar9002_hw_rf_claim(struct ath_hw *ah)
{
u32 val;
REG_WRITE(ah, AR_PHY(0), 0x00000007);
val = ar9002_hw_get_radiorev(ah);
switch (val & AR_RADIO_SREV_MAJOR) {
case 0:
val = AR_RAD5133_SREV_MAJOR;
break;
case AR_RAD5133_SREV_MAJOR:
case AR_RAD5122_SREV_MAJOR:
case AR_RAD2133_SREV_MAJOR:
case AR_RAD2122_SREV_MAJOR:
break;
default:
ath_print(ath9k_hw_common(ah), ATH_DBG_FATAL,
"Radio Chip Rev 0x%02X not supported\n",
val & AR_RADIO_SREV_MAJOR);
return -EOPNOTSUPP;
}
ah->hw_version.analog5GhzRev = val;
return 0;
}
void ar9002_hw_enable_async_fifo(struct ath_hw *ah)
{
if (AR_SREV_9287_13_OR_LATER(ah)) {
REG_SET_BIT(ah, AR_MAC_PCU_ASYNC_FIFO_REG3,
AR_MAC_PCU_ASYNC_FIFO_REG3_DATAPATH_SEL);
REG_SET_BIT(ah, AR_PHY_MODE, AR_PHY_MODE_ASYNCFIFO);
REG_CLR_BIT(ah, AR_MAC_PCU_ASYNC_FIFO_REG3,
AR_MAC_PCU_ASYNC_FIFO_REG3_SOFT_RESET);
REG_SET_BIT(ah, AR_MAC_PCU_ASYNC_FIFO_REG3,
AR_MAC_PCU_ASYNC_FIFO_REG3_SOFT_RESET);
}
}
/*
* If Async FIFO is enabled, the following counters change as MAC now runs
* at 117 Mhz instead of 88/44MHz when async FIFO is disabled.
*
* The values below tested for ht40 2 chain.
* Overwrite the delay/timeouts initialized in process ini.
*/
void ar9002_hw_update_async_fifo(struct ath_hw *ah)
{
if (AR_SREV_9287_13_OR_LATER(ah)) {
REG_WRITE(ah, AR_D_GBL_IFS_SIFS,
AR_D_GBL_IFS_SIFS_ASYNC_FIFO_DUR);
REG_WRITE(ah, AR_D_GBL_IFS_SLOT,
AR_D_GBL_IFS_SLOT_ASYNC_FIFO_DUR);
REG_WRITE(ah, AR_D_GBL_IFS_EIFS,
AR_D_GBL_IFS_EIFS_ASYNC_FIFO_DUR);
REG_WRITE(ah, AR_TIME_OUT, AR_TIME_OUT_ACK_CTS_ASYNC_FIFO_DUR);
REG_WRITE(ah, AR_USEC, AR_USEC_ASYNC_FIFO_DUR);
REG_SET_BIT(ah, AR_MAC_PCU_LOGIC_ANALYZER,
AR_MAC_PCU_LOGIC_ANALYZER_DISBUG20768);
REG_RMW_FIELD(ah, AR_AHB_MODE, AR_AHB_CUSTOM_BURST_EN,
AR_AHB_CUSTOM_BURST_ASYNC_FIFO_VAL);
}
}
/*
* We don't enable WEP aggregation on mac80211 but we keep this
* around for HAL unification purposes.
*/
void ar9002_hw_enable_wep_aggregation(struct ath_hw *ah)
{
if (AR_SREV_9287_13_OR_LATER(ah)) {
REG_SET_BIT(ah, AR_PCU_MISC_MODE2,
AR_PCU_MISC_MODE2_ENABLE_AGGWEP);
}
}
/* Sets up the AR5008/AR9001/AR9002 hardware familiy callbacks */
void ar9002_hw_attach_ops(struct ath_hw *ah)
{
struct ath_hw_private_ops *priv_ops = ath9k_hw_private_ops(ah);
struct ath_hw_ops *ops = ath9k_hw_ops(ah);
priv_ops->init_mode_regs = ar9002_hw_init_mode_regs;
priv_ops->init_mode_gain_regs = ar9002_hw_init_mode_gain_regs;
priv_ops->macversion_supported = ar9002_hw_macversion_supported;
ops->config_pci_powersave = ar9002_hw_configpcipowersave;
ar5008_hw_attach_phy_ops(ah);
if (AR_SREV_9280_10_OR_LATER(ah))
ar9002_hw_attach_phy_ops(ah);
ar9002_hw_attach_calib_ops(ah);
ar9002_hw_attach_mac_ops(ah);
ath9k: add new ANI implementation for AR9003 This adds support for ANI for AR9003. The implementation for ANI for AR9003 is slightly different than the one used for the older chipset families. It can technically be used for the older families as well but this is not yet fully tested so we only enable the new ANI for the AR5008, AR9001 and AR9002 families with a module parameter, force_new_ani. The old ANI implementation is left intact. Details of the new ANI implemention: * ANI adjustment logic is now table driven so that each ANI level setting is parameterized. This makes adjustments much more deterministic than the old procedure based logic and allows adjustments to be made incrementally to several parameters per level. * ANI register settings are now relative to INI values; so ANI param zero level == INI value. Appropriate floor and ceiling values are obeyed when adjustments are combined with INI values. * ANI processing is done once per second rather that every 100ms. The poll interval is now a set upon hardware initialization and can be picked up by the core driver. * OFDM error and CCK error processing are made in a round robin fashion rather than allowing all OFDM adjustments to be made before CCK adjustments. * ANI adjusts MRC CCK off in the presence of high CCK errors * When adjusting spur immunity (SI) and OFDM weak signal detection, ANI now sets register values for the extension channel too * When adjusting FIR step (ST), ANI now sets register for FIR step low too * FIR step adjustments now allow for an extra level of immunity for extremely noisy environments * The old Noise immunity setting (NI), which changes coarse low, size desired, etc have been removed. Changing these settings could affect up RIFS RX as well. * CCK weak signal adjustment is no longer used * ANI no longer enables phy error interrupts; in all cases phy hw counting registers are used instead * The phy error count (overflow) interrupts are also no longer used for ANI adjustments. All ANI adjustments are made via the polling routine and no adjustments are possible in the ISR context anymore * A history settings buffer is now correctly used for each channel; channel settings are initialized with the defaults but later changes are restored when returning back to that channel * When scanning, ANI is disabled settings are returned to (INI) defaults. * OFDM phy error thresholds are now 400 & 1000 (errors/second units) for low/high water marks, providing increased stability/hysteresis when changing levels. * Similarly CCK phy error thresholds are now 300 & 600 (errors/second) Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-12 12:33:45 +08:00
if (modparam_force_new_ani)
ath9k_hw_attach_ani_ops_new(ah);
else
ath9k_hw_attach_ani_ops_old(ah);
}