linux/drivers/net/wireless/ath/ath9k/hw.h

996 lines
30 KiB
C
Raw Normal View History

/*
* Copyright (c) 2008-2010 Atheros Communications Inc.
*
* Permission to use, copy, modify, and/or distribute this software for any
* purpose with or without fee is hereby granted, provided that the above
* copyright notice and this permission notice appear in all copies.
*
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
*/
#ifndef HW_H
#define HW_H
#include <linux/if_ether.h>
#include <linux/delay.h>
#include <linux/io.h>
#include "mac.h"
#include "ani.h"
#include "eeprom.h"
#include "calib.h"
#include "reg.h"
#include "phy.h"
#include "btcoex.h"
#include "../regd.h"
#include "../debug.h"
#define ATHEROS_VENDOR_ID 0x168c
#define AR5416_DEVID_PCI 0x0023
#define AR5416_DEVID_PCIE 0x0024
#define AR9160_DEVID_PCI 0x0027
#define AR9280_DEVID_PCI 0x0029
#define AR9280_DEVID_PCIE 0x002a
#define AR9285_DEVID_PCIE 0x002b
#define AR2427_DEVID_PCIE 0x002c
#define AR9287_DEVID_PCI 0x002d
#define AR9287_DEVID_PCIE 0x002e
#define AR9300_DEVID_PCIE 0x0030
#define AR5416_AR9100_DEVID 0x000b
#define AR_SUBVENDOR_ID_NOG 0x0e11
#define AR_SUBVENDOR_ID_NEW_A 0x7065
#define AR5416_MAGIC 0x19641014
#define AR9280_COEX2WIRE_SUBSYSID 0x309b
#define AT9285_COEX3WIRE_SA_SUBSYSID 0x30aa
#define AT9285_COEX3WIRE_DA_SUBSYSID 0x30ab
#define ATH_AMPDU_LIMIT_MAX (64 * 1024 - 1)
#define ATH_DEFAULT_NOISE_FLOOR -95
#define ATH9K_RSSI_BAD -128
/* Register read/write primitives */
#define REG_WRITE(_ah, _reg, _val) \
ath9k_hw_common(_ah)->ops->write((_ah), (_val), (_reg))
#define REG_READ(_ah, _reg) \
ath9k_hw_common(_ah)->ops->read((_ah), (_reg))
#define ENABLE_REGWRITE_BUFFER(_ah) \
do { \
if (AR_SREV_9271(_ah)) \
ath9k_hw_common(_ah)->ops->enable_write_buffer((_ah)); \
} while (0)
#define DISABLE_REGWRITE_BUFFER(_ah) \
do { \
if (AR_SREV_9271(_ah)) \
ath9k_hw_common(_ah)->ops->disable_write_buffer((_ah)); \
} while (0)
#define REGWRITE_BUFFER_FLUSH(_ah) \
do { \
if (AR_SREV_9271(_ah)) \
ath9k_hw_common(_ah)->ops->write_flush((_ah)); \
} while (0)
#define SM(_v, _f) (((_v) << _f##_S) & _f)
#define MS(_v, _f) (((_v) & _f) >> _f##_S)
#define REG_RMW(_a, _r, _set, _clr) \
REG_WRITE(_a, _r, (REG_READ(_a, _r) & ~(_clr)) | (_set))
#define REG_RMW_FIELD(_a, _r, _f, _v) \
REG_WRITE(_a, _r, \
(REG_READ(_a, _r) & ~_f) | (((_v) << _f##_S) & _f))
#define REG_READ_FIELD(_a, _r, _f) \
(((REG_READ(_a, _r) & _f) >> _f##_S))
#define REG_SET_BIT(_a, _r, _f) \
REG_WRITE(_a, _r, REG_READ(_a, _r) | _f)
#define REG_CLR_BIT(_a, _r, _f) \
REG_WRITE(_a, _r, REG_READ(_a, _r) & ~_f)
#define DO_DELAY(x) do { \
if ((++(x) % 64) == 0) \
udelay(1); \
} while (0)
#define REG_WRITE_ARRAY(iniarray, column, regWr) do { \
int r; \
for (r = 0; r < ((iniarray)->ia_rows); r++) { \
REG_WRITE(ah, INI_RA((iniarray), (r), 0), \
INI_RA((iniarray), r, (column))); \
DO_DELAY(regWr); \
} \
} while (0)
#define AR_GPIO_OUTPUT_MUX_AS_OUTPUT 0
#define AR_GPIO_OUTPUT_MUX_AS_PCIE_ATTENTION_LED 1
#define AR_GPIO_OUTPUT_MUX_AS_PCIE_POWER_LED 2
#define AR_GPIO_OUTPUT_MUX_AS_TX_FRAME 3
#define AR_GPIO_OUTPUT_MUX_AS_RX_CLEAR_EXTERNAL 4
#define AR_GPIO_OUTPUT_MUX_AS_MAC_NETWORK_LED 5
#define AR_GPIO_OUTPUT_MUX_AS_MAC_POWER_LED 6
#define AR_GPIOD_MASK 0x00001FFF
#define AR_GPIO_BIT(_gpio) (1 << (_gpio))
#define BASE_ACTIVATE_DELAY 100
#define RTC_PLL_SETTLE_DELAY 100
#define COEF_SCALE_S 24
#define HT40_CHANNEL_CENTER_SHIFT 10
#define ATH9K_ANTENNA0_CHAINMASK 0x1
#define ATH9K_ANTENNA1_CHAINMASK 0x2
#define ATH9K_NUM_DMA_DEBUG_REGS 8
#define ATH9K_NUM_QUEUES 10
#define MAX_RATE_POWER 63
#define AH_WAIT_TIMEOUT 100000 /* (us) */
#define AH_TSF_WRITE_TIMEOUT 100 /* (us) */
#define AH_TIME_QUANTUM 10
#define AR_KEYTABLE_SIZE 128
#define POWER_UP_TIME 10000
#define SPUR_RSSI_THRESH 40
#define CAB_TIMEOUT_VAL 10
#define BEACON_TIMEOUT_VAL 10
#define MIN_BEACON_TIMEOUT_VAL 1
#define SLEEP_SLOP 3
#define INIT_CONFIG_STATUS 0x00000000
#define INIT_RSSI_THR 0x00000700
#define INIT_BCON_CNTRL_REG 0x00000000
#define TU_TO_USEC(_tu) ((_tu) << 10)
#define ATH9K_HW_RX_HP_QDEPTH 16
#define ATH9K_HW_RX_LP_QDEPTH 128
#define PAPRD_GAIN_TABLE_ENTRIES 32
#define PAPRD_TABLE_SZ 24
enum ath_ini_subsys {
ATH_INI_PRE = 0,
ATH_INI_CORE,
ATH_INI_POST,
ATH_INI_NUM_SPLIT,
};
enum wireless_mode {
ATH9K_MODE_11A = 0,
ATH9K_MODE_11G,
ATH9K_MODE_11NA_HT20,
ATH9K_MODE_11NG_HT20,
ATH9K_MODE_11NA_HT40PLUS,
ATH9K_MODE_11NA_HT40MINUS,
ATH9K_MODE_11NG_HT40PLUS,
ATH9K_MODE_11NG_HT40MINUS,
ATH9K_MODE_MAX,
};
enum ath9k_hw_caps {
ATH9K_HW_CAP_MIC_AESCCM = BIT(0),
ATH9K_HW_CAP_MIC_CKIP = BIT(1),
ATH9K_HW_CAP_MIC_TKIP = BIT(2),
ATH9K_HW_CAP_CIPHER_AESCCM = BIT(3),
ATH9K_HW_CAP_CIPHER_CKIP = BIT(4),
ATH9K_HW_CAP_CIPHER_TKIP = BIT(5),
ATH9K_HW_CAP_VEOL = BIT(6),
ATH9K_HW_CAP_BSSIDMASK = BIT(7),
ATH9K_HW_CAP_MCAST_KEYSEARCH = BIT(8),
ATH9K_HW_CAP_HT = BIT(9),
ATH9K_HW_CAP_GTT = BIT(10),
ATH9K_HW_CAP_FASTCC = BIT(11),
ATH9K_HW_CAP_RFSILENT = BIT(12),
ATH9K_HW_CAP_CST = BIT(13),
ATH9K_HW_CAP_ENHANCEDPM = BIT(14),
ATH9K_HW_CAP_AUTOSLEEP = BIT(15),
ATH9K_HW_CAP_4KB_SPLITTRANS = BIT(16),
ATH9K_HW_CAP_EDMA = BIT(17),
ATH9K_HW_CAP_RAC_SUPPORTED = BIT(18),
ATH9K_HW_CAP_LDPC = BIT(19),
ATH9K_HW_CAP_FASTCLOCK = BIT(20),
ATH9K_HW_CAP_SGI_20 = BIT(21),
ATH9K_HW_CAP_PAPRD = BIT(22),
};
struct ath9k_hw_capabilities {
u32 hw_caps; /* ATH9K_HW_CAP_* from ath9k_hw_caps */
DECLARE_BITMAP(wireless_modes, ATH9K_MODE_MAX); /* ATH9K_MODE_* */
u16 total_queues;
u16 keycache_size;
u16 low_5ghz_chan, high_5ghz_chan;
u16 low_2ghz_chan, high_2ghz_chan;
u16 rts_aggr_limit;
u8 tx_chainmask;
u8 rx_chainmask;
u16 tx_triglevel_max;
u16 reg_cap;
u8 num_gpio_pins;
u8 num_antcfg_2ghz;
u8 num_antcfg_5ghz;
u8 rx_hp_qdepth;
u8 rx_lp_qdepth;
u8 rx_status_len;
u8 tx_desc_len;
u8 txs_len;
};
struct ath9k_ops_config {
int dma_beacon_response_time;
int sw_beacon_response_time;
int additional_swba_backoff;
int ack_6mb;
u32 cwm_ignore_extcca;
u8 pcie_powersave_enable;
bool pcieSerDesWrite;
u8 pcie_clock_req;
u32 pcie_waen;
u8 analog_shiftreg;
u8 ht_enable;
u32 ofdm_trig_low;
u32 ofdm_trig_high;
u32 cck_trig_high;
u32 cck_trig_low;
u32 enable_ani;
int serialize_regmode;
bool rx_intr_mitigation;
bool tx_intr_mitigation;
#define SPUR_DISABLE 0
#define SPUR_ENABLE_IOCTL 1
#define SPUR_ENABLE_EEPROM 2
#define AR_EEPROM_MODAL_SPURS 5
#define AR_SPUR_5413_1 1640
#define AR_SPUR_5413_2 1200
#define AR_NO_SPUR 0x8000
#define AR_BASE_FREQ_2GHZ 2300
#define AR_BASE_FREQ_5GHZ 4900
#define AR_SPUR_FEEQ_BOUND_HT40 19
#define AR_SPUR_FEEQ_BOUND_HT20 10
int spurmode;
u16 spurchans[AR_EEPROM_MODAL_SPURS][2];
ath9k: Fix maximum tx fifo settings for single stream devices Atheros single stream AR9285 and AR9271 have half the PCU TX FIFO buffer size of that of dual stream devices. Dual stream devices have a max PCU TX FIFO size of 8 KB while single stream devices have 4 KB. Single stream devices have an issue though and require hardware only to use half of the amount of its capable PCU TX FIFO size, 2 KB and this requires a change in software. Technically a change would not have been required (except for frame burst considerations of 128 bytes) if these devices would have been able to use the full 4 KB of the PCU TX FIFO size but our systems engineers recommend 2 KB to be used only. We enforce this through software by reducing the max frame triggger level to 2 KB. Fixing the max frame trigger level should then have a few benefits: * The PER will now be adjusted as designed for underruns when the max trigger level is reached. This should help alleviate the bus as the rate control algorithm chooses a slower rate which should ensure frames are transmitted properly under high system bus load. * The poll we use on our TX queues should now trigger and work as designed for single stream devices. The hardware passes data from each TX queue on the PCU TX FIFO queue respecting each queue's priority. The new trigger level ensures this seeding of the PCU TX FIFO queue occurs as designed which could mean avoiding false resets and actually reseting hw correctly when a TX queue is indeed stuck. * Some undocumented / unsupported behaviour could have been triggered when the max trigger level level was being set to 4 KB on single stream devices. Its not clear what this issue was to me yet. Cc: Kyungwan Nam <kyungwan.nam@atheros.com> Cc: Bennyam Malavazi <bennyam.malavazi@atheros.com> Cc: Stephen Chen <stephen.chen@atheros.com> Cc: Shan Palanisamy <shan.palanisamy@atheros.com> Cc: Paul Shaw <paul.shaw@atheros.com> Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-25 10:37:57 +08:00
u8 max_txtrig_level;
ath9k: add new ANI implementation for AR9003 This adds support for ANI for AR9003. The implementation for ANI for AR9003 is slightly different than the one used for the older chipset families. It can technically be used for the older families as well but this is not yet fully tested so we only enable the new ANI for the AR5008, AR9001 and AR9002 families with a module parameter, force_new_ani. The old ANI implementation is left intact. Details of the new ANI implemention: * ANI adjustment logic is now table driven so that each ANI level setting is parameterized. This makes adjustments much more deterministic than the old procedure based logic and allows adjustments to be made incrementally to several parameters per level. * ANI register settings are now relative to INI values; so ANI param zero level == INI value. Appropriate floor and ceiling values are obeyed when adjustments are combined with INI values. * ANI processing is done once per second rather that every 100ms. The poll interval is now a set upon hardware initialization and can be picked up by the core driver. * OFDM error and CCK error processing are made in a round robin fashion rather than allowing all OFDM adjustments to be made before CCK adjustments. * ANI adjusts MRC CCK off in the presence of high CCK errors * When adjusting spur immunity (SI) and OFDM weak signal detection, ANI now sets register values for the extension channel too * When adjusting FIR step (ST), ANI now sets register for FIR step low too * FIR step adjustments now allow for an extra level of immunity for extremely noisy environments * The old Noise immunity setting (NI), which changes coarse low, size desired, etc have been removed. Changing these settings could affect up RIFS RX as well. * CCK weak signal adjustment is no longer used * ANI no longer enables phy error interrupts; in all cases phy hw counting registers are used instead * The phy error count (overflow) interrupts are also no longer used for ANI adjustments. All ANI adjustments are made via the polling routine and no adjustments are possible in the ISR context anymore * A history settings buffer is now correctly used for each channel; channel settings are initialized with the defaults but later changes are restored when returning back to that channel * When scanning, ANI is disabled settings are returned to (INI) defaults. * OFDM phy error thresholds are now 400 & 1000 (errors/second units) for low/high water marks, providing increased stability/hysteresis when changing levels. * Similarly CCK phy error thresholds are now 300 & 600 (errors/second) Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-12 12:33:45 +08:00
u16 ani_poll_interval; /* ANI poll interval in ms */
};
enum ath9k_int {
ATH9K_INT_RX = 0x00000001,
ATH9K_INT_RXDESC = 0x00000002,
ATH9K_INT_RXHP = 0x00000001,
ATH9K_INT_RXLP = 0x00000002,
ATH9K_INT_RXNOFRM = 0x00000008,
ATH9K_INT_RXEOL = 0x00000010,
ATH9K_INT_RXORN = 0x00000020,
ATH9K_INT_TX = 0x00000040,
ATH9K_INT_TXDESC = 0x00000080,
ATH9K_INT_TIM_TIMER = 0x00000100,
ATH9K_INT_BB_WATCHDOG = 0x00000400,
ATH9K_INT_TXURN = 0x00000800,
ATH9K_INT_MIB = 0x00001000,
ATH9K_INT_RXPHY = 0x00004000,
ATH9K_INT_RXKCM = 0x00008000,
ATH9K_INT_SWBA = 0x00010000,
ATH9K_INT_BMISS = 0x00040000,
ATH9K_INT_BNR = 0x00100000,
ATH9K_INT_TIM = 0x00200000,
ATH9K_INT_DTIM = 0x00400000,
ATH9K_INT_DTIMSYNC = 0x00800000,
ATH9K_INT_GPIO = 0x01000000,
ATH9K_INT_CABEND = 0x02000000,
ATH9K_INT_TSFOOR = 0x04000000,
ATH9K_INT_GENTIMER = 0x08000000,
ATH9K_INT_CST = 0x10000000,
ATH9K_INT_GTT = 0x20000000,
ATH9K_INT_FATAL = 0x40000000,
ATH9K_INT_GLOBAL = 0x80000000,
ATH9K_INT_BMISC = ATH9K_INT_TIM |
ATH9K_INT_DTIM |
ATH9K_INT_DTIMSYNC |
ATH9K_INT_TSFOOR |
ATH9K_INT_CABEND,
ATH9K_INT_COMMON = ATH9K_INT_RXNOFRM |
ATH9K_INT_RXDESC |
ATH9K_INT_RXEOL |
ATH9K_INT_RXORN |
ATH9K_INT_TXURN |
ATH9K_INT_TXDESC |
ATH9K_INT_MIB |
ATH9K_INT_RXPHY |
ATH9K_INT_RXKCM |
ATH9K_INT_SWBA |
ATH9K_INT_BMISS |
ATH9K_INT_GPIO,
ATH9K_INT_NOCARD = 0xffffffff
};
#define CHANNEL_CW_INT 0x00002
#define CHANNEL_CCK 0x00020
#define CHANNEL_OFDM 0x00040
#define CHANNEL_2GHZ 0x00080
#define CHANNEL_5GHZ 0x00100
#define CHANNEL_PASSIVE 0x00200
#define CHANNEL_DYN 0x00400
#define CHANNEL_HALF 0x04000
#define CHANNEL_QUARTER 0x08000
#define CHANNEL_HT20 0x10000
#define CHANNEL_HT40PLUS 0x20000
#define CHANNEL_HT40MINUS 0x40000
#define CHANNEL_A (CHANNEL_5GHZ|CHANNEL_OFDM)
#define CHANNEL_B (CHANNEL_2GHZ|CHANNEL_CCK)
#define CHANNEL_G (CHANNEL_2GHZ|CHANNEL_OFDM)
#define CHANNEL_G_HT20 (CHANNEL_2GHZ|CHANNEL_HT20)
#define CHANNEL_A_HT20 (CHANNEL_5GHZ|CHANNEL_HT20)
#define CHANNEL_G_HT40PLUS (CHANNEL_2GHZ|CHANNEL_HT40PLUS)
#define CHANNEL_G_HT40MINUS (CHANNEL_2GHZ|CHANNEL_HT40MINUS)
#define CHANNEL_A_HT40PLUS (CHANNEL_5GHZ|CHANNEL_HT40PLUS)
#define CHANNEL_A_HT40MINUS (CHANNEL_5GHZ|CHANNEL_HT40MINUS)
#define CHANNEL_ALL \
(CHANNEL_OFDM| \
CHANNEL_CCK| \
CHANNEL_2GHZ | \
CHANNEL_5GHZ | \
CHANNEL_HT20 | \
CHANNEL_HT40PLUS | \
CHANNEL_HT40MINUS)
struct ath9k_channel {
struct ieee80211_channel *chan;
u16 channel;
u32 channelFlags;
u32 chanmode;
int32_t CalValid;
bool oneTimeCalsDone;
int8_t iCoff;
int8_t qCoff;
int16_t rawNoiseFloor;
bool paprd_done;
u16 small_signal_gain[AR9300_MAX_CHAINS];
u32 pa_table[AR9300_MAX_CHAINS][PAPRD_TABLE_SZ];
};
#define IS_CHAN_G(_c) ((((_c)->channelFlags & (CHANNEL_G)) == CHANNEL_G) || \
(((_c)->channelFlags & CHANNEL_G_HT20) == CHANNEL_G_HT20) || \
(((_c)->channelFlags & CHANNEL_G_HT40PLUS) == CHANNEL_G_HT40PLUS) || \
(((_c)->channelFlags & CHANNEL_G_HT40MINUS) == CHANNEL_G_HT40MINUS))
#define IS_CHAN_OFDM(_c) (((_c)->channelFlags & CHANNEL_OFDM) != 0)
#define IS_CHAN_5GHZ(_c) (((_c)->channelFlags & CHANNEL_5GHZ) != 0)
#define IS_CHAN_2GHZ(_c) (((_c)->channelFlags & CHANNEL_2GHZ) != 0)
#define IS_CHAN_HALF_RATE(_c) (((_c)->channelFlags & CHANNEL_HALF) != 0)
#define IS_CHAN_QUARTER_RATE(_c) (((_c)->channelFlags & CHANNEL_QUARTER) != 0)
#define IS_CHAN_A_FAST_CLOCK(_ah, _c) \
((((_c)->channelFlags & CHANNEL_5GHZ) != 0) && \
((_ah)->caps.hw_caps & ATH9K_HW_CAP_FASTCLOCK))
/* These macros check chanmode and not channelFlags */
#define IS_CHAN_B(_c) ((_c)->chanmode == CHANNEL_B)
#define IS_CHAN_HT20(_c) (((_c)->chanmode == CHANNEL_A_HT20) || \
((_c)->chanmode == CHANNEL_G_HT20))
#define IS_CHAN_HT40(_c) (((_c)->chanmode == CHANNEL_A_HT40PLUS) || \
((_c)->chanmode == CHANNEL_A_HT40MINUS) || \
((_c)->chanmode == CHANNEL_G_HT40PLUS) || \
((_c)->chanmode == CHANNEL_G_HT40MINUS))
#define IS_CHAN_HT(_c) (IS_CHAN_HT20((_c)) || IS_CHAN_HT40((_c)))
enum ath9k_power_mode {
ATH9K_PM_AWAKE = 0,
ATH9K_PM_FULL_SLEEP,
ATH9K_PM_NETWORK_SLEEP,
ATH9K_PM_UNDEFINED
};
enum ath9k_tp_scale {
ATH9K_TP_SCALE_MAX = 0,
ATH9K_TP_SCALE_50,
ATH9K_TP_SCALE_25,
ATH9K_TP_SCALE_12,
ATH9K_TP_SCALE_MIN
};
enum ser_reg_mode {
SER_REG_MODE_OFF = 0,
SER_REG_MODE_ON = 1,
SER_REG_MODE_AUTO = 2,
};
enum ath9k_rx_qtype {
ATH9K_RX_QUEUE_HP,
ATH9K_RX_QUEUE_LP,
ATH9K_RX_QUEUE_MAX,
};
struct ath9k_beacon_state {
u32 bs_nexttbtt;
u32 bs_nextdtim;
u32 bs_intval;
#define ATH9K_BEACON_PERIOD 0x0000ffff
#define ATH9K_BEACON_ENA 0x00800000
#define ATH9K_BEACON_RESET_TSF 0x01000000
#define ATH9K_TSFOOR_THRESHOLD 0x00004240 /* 16k us */
u32 bs_dtimperiod;
u16 bs_cfpperiod;
u16 bs_cfpmaxduration;
u32 bs_cfpnext;
u16 bs_timoffset;
u16 bs_bmissthreshold;
u32 bs_sleepduration;
u32 bs_tsfoor_threshold;
};
struct chan_centers {
u16 synth_center;
u16 ctl_center;
u16 ext_center;
};
enum {
ATH9K_RESET_POWER_ON,
ATH9K_RESET_WARM,
ATH9K_RESET_COLD,
};
struct ath9k_hw_version {
u32 magic;
u16 devid;
u16 subvendorid;
u32 macVersion;
u16 macRev;
u16 phyRev;
u16 analog5GhzRev;
u16 analog2GhzRev;
u16 subsysid;
};
/* Generic TSF timer definitions */
#define ATH_MAX_GEN_TIMER 16
#define AR_GENTMR_BIT(_index) (1 << (_index))
/*
* Using de Bruijin sequence to look up 1's index in a 32 bit number
* debruijn32 = 0000 0111 0111 1100 1011 0101 0011 0001
*/
#define debruijn32 0x077CB531U
struct ath_gen_timer_configuration {
u32 next_addr;
u32 period_addr;
u32 mode_addr;
u32 mode_mask;
};
struct ath_gen_timer {
void (*trigger)(void *arg);
void (*overflow)(void *arg);
void *arg;
u8 index;
};
struct ath_gen_timer_table {
u32 gen_timer_index[32];
struct ath_gen_timer *timers[ATH_MAX_GEN_TIMER];
union {
unsigned long timer_bits;
u16 val;
} timer_mask;
};
/**
* struct ath_hw_private_ops - callbacks used internally by hardware code
*
* This structure contains private callbacks designed to only be used internally
* by the hardware core.
*
* @init_cal_settings: setup types of calibrations supported
* @init_cal: starts actual calibration
*
* @init_mode_regs: Initializes mode registers
* @init_mode_gain_regs: Initialize TX/RX gain registers
* @macversion_supported: If this specific mac revision is supported
*
* @rf_set_freq: change frequency
* @spur_mitigate_freq: spur mitigation
* @rf_alloc_ext_banks:
* @rf_free_ext_banks:
* @set_rf_regs:
* @compute_pll_control: compute the PLL control value to use for
* AR_RTC_PLL_CONTROL for a given channel
* @setup_calibration: set up calibration
* @iscal_supported: used to query if a type of calibration is supported
* @loadnf: load noise floor read from each chain on the CCA registers
*
* @ani_reset: reset ANI parameters to default values
* @ani_lower_immunity: lower the noise immunity level. The level controls
* the power-based packet detection on hardware. If a power jump is
* detected the adapter takes it as an indication that a packet has
* arrived. The level ranges from 0-5. Each level corresponds to a
* few dB more of noise immunity. If you have a strong time-varying
* interference that is causing false detections (OFDM timing errors or
* CCK timing errors) the level can be increased.
ath9k: add new ANI implementation for AR9003 This adds support for ANI for AR9003. The implementation for ANI for AR9003 is slightly different than the one used for the older chipset families. It can technically be used for the older families as well but this is not yet fully tested so we only enable the new ANI for the AR5008, AR9001 and AR9002 families with a module parameter, force_new_ani. The old ANI implementation is left intact. Details of the new ANI implemention: * ANI adjustment logic is now table driven so that each ANI level setting is parameterized. This makes adjustments much more deterministic than the old procedure based logic and allows adjustments to be made incrementally to several parameters per level. * ANI register settings are now relative to INI values; so ANI param zero level == INI value. Appropriate floor and ceiling values are obeyed when adjustments are combined with INI values. * ANI processing is done once per second rather that every 100ms. The poll interval is now a set upon hardware initialization and can be picked up by the core driver. * OFDM error and CCK error processing are made in a round robin fashion rather than allowing all OFDM adjustments to be made before CCK adjustments. * ANI adjusts MRC CCK off in the presence of high CCK errors * When adjusting spur immunity (SI) and OFDM weak signal detection, ANI now sets register values for the extension channel too * When adjusting FIR step (ST), ANI now sets register for FIR step low too * FIR step adjustments now allow for an extra level of immunity for extremely noisy environments * The old Noise immunity setting (NI), which changes coarse low, size desired, etc have been removed. Changing these settings could affect up RIFS RX as well. * CCK weak signal adjustment is no longer used * ANI no longer enables phy error interrupts; in all cases phy hw counting registers are used instead * The phy error count (overflow) interrupts are also no longer used for ANI adjustments. All ANI adjustments are made via the polling routine and no adjustments are possible in the ISR context anymore * A history settings buffer is now correctly used for each channel; channel settings are initialized with the defaults but later changes are restored when returning back to that channel * When scanning, ANI is disabled settings are returned to (INI) defaults. * OFDM phy error thresholds are now 400 & 1000 (errors/second units) for low/high water marks, providing increased stability/hysteresis when changing levels. * Similarly CCK phy error thresholds are now 300 & 600 (errors/second) Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-12 12:33:45 +08:00
* @ani_cache_ini_regs: cache the values for ANI from the initial
* register settings through the register initialization.
*/
struct ath_hw_private_ops {
/* Calibration ops */
void (*init_cal_settings)(struct ath_hw *ah);
bool (*init_cal)(struct ath_hw *ah, struct ath9k_channel *chan);
void (*init_mode_regs)(struct ath_hw *ah);
void (*init_mode_gain_regs)(struct ath_hw *ah);
bool (*macversion_supported)(u32 macversion);
void (*setup_calibration)(struct ath_hw *ah,
struct ath9k_cal_list *currCal);
bool (*iscal_supported)(struct ath_hw *ah,
enum ath9k_cal_types calType);
/* PHY ops */
int (*rf_set_freq)(struct ath_hw *ah,
struct ath9k_channel *chan);
void (*spur_mitigate_freq)(struct ath_hw *ah,
struct ath9k_channel *chan);
int (*rf_alloc_ext_banks)(struct ath_hw *ah);
void (*rf_free_ext_banks)(struct ath_hw *ah);
bool (*set_rf_regs)(struct ath_hw *ah,
struct ath9k_channel *chan,
u16 modesIndex);
void (*set_channel_regs)(struct ath_hw *ah, struct ath9k_channel *chan);
void (*init_bb)(struct ath_hw *ah,
struct ath9k_channel *chan);
int (*process_ini)(struct ath_hw *ah, struct ath9k_channel *chan);
void (*olc_init)(struct ath_hw *ah);
void (*set_rfmode)(struct ath_hw *ah, struct ath9k_channel *chan);
void (*mark_phy_inactive)(struct ath_hw *ah);
void (*set_delta_slope)(struct ath_hw *ah, struct ath9k_channel *chan);
bool (*rfbus_req)(struct ath_hw *ah);
void (*rfbus_done)(struct ath_hw *ah);
void (*enable_rfkill)(struct ath_hw *ah);
void (*restore_chainmask)(struct ath_hw *ah);
void (*set_diversity)(struct ath_hw *ah, bool value);
u32 (*compute_pll_control)(struct ath_hw *ah,
struct ath9k_channel *chan);
bool (*ani_control)(struct ath_hw *ah, enum ath9k_ani_cmd cmd,
int param);
void (*do_getnf)(struct ath_hw *ah, int16_t nfarray[NUM_NF_READINGS]);
void (*loadnf)(struct ath_hw *ah, struct ath9k_channel *chan);
/* ANI */
void (*ani_reset)(struct ath_hw *ah, bool is_scanning);
void (*ani_lower_immunity)(struct ath_hw *ah);
ath9k: add new ANI implementation for AR9003 This adds support for ANI for AR9003. The implementation for ANI for AR9003 is slightly different than the one used for the older chipset families. It can technically be used for the older families as well but this is not yet fully tested so we only enable the new ANI for the AR5008, AR9001 and AR9002 families with a module parameter, force_new_ani. The old ANI implementation is left intact. Details of the new ANI implemention: * ANI adjustment logic is now table driven so that each ANI level setting is parameterized. This makes adjustments much more deterministic than the old procedure based logic and allows adjustments to be made incrementally to several parameters per level. * ANI register settings are now relative to INI values; so ANI param zero level == INI value. Appropriate floor and ceiling values are obeyed when adjustments are combined with INI values. * ANI processing is done once per second rather that every 100ms. The poll interval is now a set upon hardware initialization and can be picked up by the core driver. * OFDM error and CCK error processing are made in a round robin fashion rather than allowing all OFDM adjustments to be made before CCK adjustments. * ANI adjusts MRC CCK off in the presence of high CCK errors * When adjusting spur immunity (SI) and OFDM weak signal detection, ANI now sets register values for the extension channel too * When adjusting FIR step (ST), ANI now sets register for FIR step low too * FIR step adjustments now allow for an extra level of immunity for extremely noisy environments * The old Noise immunity setting (NI), which changes coarse low, size desired, etc have been removed. Changing these settings could affect up RIFS RX as well. * CCK weak signal adjustment is no longer used * ANI no longer enables phy error interrupts; in all cases phy hw counting registers are used instead * The phy error count (overflow) interrupts are also no longer used for ANI adjustments. All ANI adjustments are made via the polling routine and no adjustments are possible in the ISR context anymore * A history settings buffer is now correctly used for each channel; channel settings are initialized with the defaults but later changes are restored when returning back to that channel * When scanning, ANI is disabled settings are returned to (INI) defaults. * OFDM phy error thresholds are now 400 & 1000 (errors/second units) for low/high water marks, providing increased stability/hysteresis when changing levels. * Similarly CCK phy error thresholds are now 300 & 600 (errors/second) Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-12 12:33:45 +08:00
void (*ani_cache_ini_regs)(struct ath_hw *ah);
};
/**
* struct ath_hw_ops - callbacks used by hardware code and driver code
*
* This structure contains callbacks designed to to be used internally by
* hardware code and also by the lower level driver.
*
* @config_pci_powersave:
* @calibrate: periodic calibration for NF, ANI, IQ, ADC gain, ADC-DC
*
* @ani_proc_mib_event: process MIB events, this would happen upon specific ANI
* thresholds being reached or having overflowed.
* @ani_monitor: called periodically by the core driver to collect
* MIB stats and adjust ANI if specific thresholds have been reached.
*/
struct ath_hw_ops {
void (*config_pci_powersave)(struct ath_hw *ah,
int restore,
int power_off);
void (*rx_enable)(struct ath_hw *ah);
void (*set_desc_link)(void *ds, u32 link);
void (*get_desc_link)(void *ds, u32 **link);
bool (*calibrate)(struct ath_hw *ah,
struct ath9k_channel *chan,
u8 rxchainmask,
bool longcal);
bool (*get_isr)(struct ath_hw *ah, enum ath9k_int *masked);
void (*fill_txdesc)(struct ath_hw *ah, void *ds, u32 seglen,
bool is_firstseg, bool is_is_lastseg,
const void *ds0, dma_addr_t buf_addr,
unsigned int qcu);
int (*proc_txdesc)(struct ath_hw *ah, void *ds,
struct ath_tx_status *ts);
void (*set11n_txdesc)(struct ath_hw *ah, void *ds,
u32 pktLen, enum ath9k_pkt_type type,
u32 txPower, u32 keyIx,
enum ath9k_key_type keyType,
u32 flags);
void (*set11n_ratescenario)(struct ath_hw *ah, void *ds,
void *lastds,
u32 durUpdateEn, u32 rtsctsRate,
u32 rtsctsDuration,
struct ath9k_11n_rate_series series[],
u32 nseries, u32 flags);
void (*set11n_aggr_first)(struct ath_hw *ah, void *ds,
u32 aggrLen);
void (*set11n_aggr_middle)(struct ath_hw *ah, void *ds,
u32 numDelims);
void (*set11n_aggr_last)(struct ath_hw *ah, void *ds);
void (*clr11n_aggr)(struct ath_hw *ah, void *ds);
void (*set11n_burstduration)(struct ath_hw *ah, void *ds,
u32 burstDuration);
void (*set11n_virtualmorefrag)(struct ath_hw *ah, void *ds,
u32 vmf);
void (*ani_proc_mib_event)(struct ath_hw *ah);
void (*ani_monitor)(struct ath_hw *ah, struct ath9k_channel *chan);
};
struct ath_nf_limits {
s16 max;
s16 min;
s16 nominal;
};
struct ath_hw {
struct ieee80211_hw *hw;
struct ath_common common;
struct ath9k_hw_version hw_version;
struct ath9k_ops_config config;
struct ath9k_hw_capabilities caps;
struct ath9k_channel channels[38];
struct ath9k_channel *curchan;
union {
struct ar5416_eeprom_def def;
struct ar5416_eeprom_4k map4k;
struct ar9287_eeprom map9287;
struct ar9300_eeprom ar9300_eep;
} eeprom;
const struct eeprom_ops *eep_ops;
bool sw_mgmt_crypto;
bool is_pciexpress;
bool need_an_top2_fixup;
u16 tx_trig_level;
struct ath_nf_limits nf_2g;
struct ath_nf_limits nf_5g;
u16 rfsilent;
u32 rfkill_gpio;
u32 rfkill_polarity;
u32 ah_flags;
bool htc_reset_init;
enum nl80211_iftype opmode;
enum ath9k_power_mode power_mode;
struct ath9k_nfcal_hist nfCalHist[NUM_NF_READINGS];
struct ath9k_pacal_info pacal_info;
struct ar5416Stats stats;
struct ath9k_tx_queue_info txq[ATH9K_NUM_TX_QUEUES];
int16_t curchan_rad_index;
enum ath9k_int imask;
u32 imrs2_reg;
u32 txok_interrupt_mask;
u32 txerr_interrupt_mask;
u32 txdesc_interrupt_mask;
u32 txeol_interrupt_mask;
u32 txurn_interrupt_mask;
bool chip_fullsleep;
u32 atim_window;
/* Calibration */
enum ath9k_cal_types supp_cals;
struct ath9k_cal_list iq_caldata;
struct ath9k_cal_list adcgain_caldata;
struct ath9k_cal_list adcdc_calinitdata;
struct ath9k_cal_list adcdc_caldata;
struct ath9k_cal_list tempCompCalData;
struct ath9k_cal_list *cal_list;
struct ath9k_cal_list *cal_list_last;
struct ath9k_cal_list *cal_list_curr;
#define totalPowerMeasI meas0.unsign
#define totalPowerMeasQ meas1.unsign
#define totalIqCorrMeas meas2.sign
#define totalAdcIOddPhase meas0.unsign
#define totalAdcIEvenPhase meas1.unsign
#define totalAdcQOddPhase meas2.unsign
#define totalAdcQEvenPhase meas3.unsign
#define totalAdcDcOffsetIOddPhase meas0.sign
#define totalAdcDcOffsetIEvenPhase meas1.sign
#define totalAdcDcOffsetQOddPhase meas2.sign
#define totalAdcDcOffsetQEvenPhase meas3.sign
union {
u32 unsign[AR5416_MAX_CHAINS];
int32_t sign[AR5416_MAX_CHAINS];
} meas0;
union {
u32 unsign[AR5416_MAX_CHAINS];
int32_t sign[AR5416_MAX_CHAINS];
} meas1;
union {
u32 unsign[AR5416_MAX_CHAINS];
int32_t sign[AR5416_MAX_CHAINS];
} meas2;
union {
u32 unsign[AR5416_MAX_CHAINS];
int32_t sign[AR5416_MAX_CHAINS];
} meas3;
u16 cal_samples;
u32 sta_id1_defaults;
u32 misc_mode;
enum {
AUTO_32KHZ,
USE_32KHZ,
DONT_USE_32KHZ,
} enable_32kHz_clock;
/* Private to hardware code */
struct ath_hw_private_ops private_ops;
/* Accessed by the lower level driver */
struct ath_hw_ops ops;
/* Used to program the radio on non single-chip devices */
u32 *analogBank0Data;
u32 *analogBank1Data;
u32 *analogBank2Data;
u32 *analogBank3Data;
u32 *analogBank6Data;
u32 *analogBank6TPCData;
u32 *analogBank7Data;
u32 *addac5416_21;
u32 *bank6Temp;
u8 txpower_limit;
int16_t txpower_indexoffset;
int coverage_class;
u32 beacon_interval;
u32 slottime;
u32 globaltxtimeout;
/* ANI */
u32 proc_phyerr;
u32 aniperiod;
struct ar5416AniState *curani;
struct ar5416AniState ani[255];
int totalSizeDesired[5];
int coarse_high[5];
int coarse_low[5];
int firpwr[5];
enum ath9k_ani_cmd ani_function;
/* Bluetooth coexistance */
struct ath_btcoex_hw btcoex_hw;
u32 intr_txqs;
u8 txchainmask;
u8 rxchainmask;
u32 originalGain[22];
int initPDADC;
int PDADCdelta;
u8 led_pin;
struct ar5416IniArray iniModes;
struct ar5416IniArray iniCommon;
struct ar5416IniArray iniBank0;
struct ar5416IniArray iniBB_RfGain;
struct ar5416IniArray iniBank1;
struct ar5416IniArray iniBank2;
struct ar5416IniArray iniBank3;
struct ar5416IniArray iniBank6;
struct ar5416IniArray iniBank6TPC;
struct ar5416IniArray iniBank7;
struct ar5416IniArray iniAddac;
struct ar5416IniArray iniPcieSerdes;
struct ar5416IniArray iniPcieSerdesLowPower;
struct ar5416IniArray iniModesAdditional;
struct ar5416IniArray iniModesRxGain;
struct ar5416IniArray iniModesTxGain;
struct ar5416IniArray iniModes_9271_1_0_only;
struct ar5416IniArray iniCckfirNormal;
struct ar5416IniArray iniCckfirJapan2484;
struct ar5416IniArray iniCommon_normal_cck_fir_coeff_9271;
struct ar5416IniArray iniCommon_japan_2484_cck_fir_coeff_9271;
struct ar5416IniArray iniModes_9271_ANI_reg;
struct ar5416IniArray iniModes_high_power_tx_gain_9271;
struct ar5416IniArray iniModes_normal_power_tx_gain_9271;
struct ar5416IniArray iniMac[ATH_INI_NUM_SPLIT];
struct ar5416IniArray iniBB[ATH_INI_NUM_SPLIT];
struct ar5416IniArray iniRadio[ATH_INI_NUM_SPLIT];
struct ar5416IniArray iniSOC[ATH_INI_NUM_SPLIT];
u32 intr_gen_timer_trigger;
u32 intr_gen_timer_thresh;
struct ath_gen_timer_table hw_gen_timers;
struct ar9003_txs *ts_ring;
void *ts_start;
u32 ts_paddr_start;
u32 ts_paddr_end;
u16 ts_tail;
u8 ts_size;
u32 bb_watchdog_last_status;
u32 bb_watchdog_timeout_ms; /* in ms, 0 to disable */
u32 paprd_gain_table_entries[PAPRD_GAIN_TABLE_ENTRIES];
u8 paprd_gain_table_index[PAPRD_GAIN_TABLE_ENTRIES];
/*
* Store the permanent value of Reg 0x4004in WARegVal
* so we dont have to R/M/W. We should not be reading
* this register when in sleep states.
*/
u32 WARegVal;
};
static inline struct ath_common *ath9k_hw_common(struct ath_hw *ah)
{
return &ah->common;
}
static inline struct ath_regulatory *ath9k_hw_regulatory(struct ath_hw *ah)
{
return &(ath9k_hw_common(ah)->regulatory);
}
static inline struct ath_hw_private_ops *ath9k_hw_private_ops(struct ath_hw *ah)
{
return &ah->private_ops;
}
static inline struct ath_hw_ops *ath9k_hw_ops(struct ath_hw *ah)
{
return &ah->ops;
}
/* Initialization, Detach, Reset */
const char *ath9k_hw_probe(u16 vendorid, u16 devid);
void ath9k_hw_deinit(struct ath_hw *ah);
int ath9k_hw_init(struct ath_hw *ah);
int ath9k_hw_reset(struct ath_hw *ah, struct ath9k_channel *chan,
bool bChannelChange);
int ath9k_hw_fill_cap_info(struct ath_hw *ah);
u32 ath9k_regd_get_ctl(struct ath_regulatory *reg, struct ath9k_channel *chan);
/* Key Cache Management */
bool ath9k_hw_keyreset(struct ath_hw *ah, u16 entry);
bool ath9k_hw_set_keycache_entry(struct ath_hw *ah, u16 entry,
const struct ath9k_keyval *k,
const u8 *mac);
/* GPIO / RFKILL / Antennae */
void ath9k_hw_cfg_gpio_input(struct ath_hw *ah, u32 gpio);
u32 ath9k_hw_gpio_get(struct ath_hw *ah, u32 gpio);
void ath9k_hw_cfg_output(struct ath_hw *ah, u32 gpio,
u32 ah_signal_type);
void ath9k_hw_set_gpio(struct ath_hw *ah, u32 gpio, u32 val);
u32 ath9k_hw_getdefantenna(struct ath_hw *ah);
void ath9k_hw_setantenna(struct ath_hw *ah, u32 antenna);
/* General Operation */
bool ath9k_hw_wait(struct ath_hw *ah, u32 reg, u32 mask, u32 val, u32 timeout);
u32 ath9k_hw_reverse_bits(u32 val, u32 n);
bool ath9k_get_channel_edges(struct ath_hw *ah, u16 flags, u16 *low, u16 *high);
u16 ath9k_hw_computetxtime(struct ath_hw *ah,
u8 phy, int kbps,
u32 frameLen, u16 rateix, bool shortPreamble);
void ath9k_hw_get_channel_centers(struct ath_hw *ah,
struct ath9k_channel *chan,
struct chan_centers *centers);
u32 ath9k_hw_getrxfilter(struct ath_hw *ah);
void ath9k_hw_setrxfilter(struct ath_hw *ah, u32 bits);
bool ath9k_hw_phy_disable(struct ath_hw *ah);
bool ath9k_hw_disable(struct ath_hw *ah);
void ath9k_hw_set_txpowerlimit(struct ath_hw *ah, u32 limit);
void ath9k_hw_setopmode(struct ath_hw *ah);
void ath9k_hw_setmcastfilter(struct ath_hw *ah, u32 filter0, u32 filter1);
void ath9k_hw_setbssidmask(struct ath_hw *ah);
void ath9k_hw_write_associd(struct ath_hw *ah);
u64 ath9k_hw_gettsf64(struct ath_hw *ah);
void ath9k_hw_settsf64(struct ath_hw *ah, u64 tsf64);
void ath9k_hw_reset_tsf(struct ath_hw *ah);
void ath9k_hw_set_tsfadjust(struct ath_hw *ah, u32 setting);
void ath9k_hw_init_global_settings(struct ath_hw *ah);
void ath9k_hw_set11nmac2040(struct ath_hw *ah);
void ath9k_hw_beaconinit(struct ath_hw *ah, u32 next_beacon, u32 beacon_period);
void ath9k_hw_set_sta_beacon_timers(struct ath_hw *ah,
const struct ath9k_beacon_state *bs);
bool ath9k_hw_check_alive(struct ath_hw *ah);
bool ath9k_hw_setpower(struct ath_hw *ah, enum ath9k_power_mode mode);
/* Generic hw timer primitives */
struct ath_gen_timer *ath_gen_timer_alloc(struct ath_hw *ah,
void (*trigger)(void *),
void (*overflow)(void *),
void *arg,
u8 timer_index);
void ath9k_hw_gen_timer_start(struct ath_hw *ah,
struct ath_gen_timer *timer,
u32 timer_next,
u32 timer_period);
void ath9k_hw_gen_timer_stop(struct ath_hw *ah, struct ath_gen_timer *timer);
void ath_gen_timer_free(struct ath_hw *ah, struct ath_gen_timer *timer);
void ath_gen_timer_isr(struct ath_hw *hw);
u32 ath9k_hw_gettsf32(struct ath_hw *ah);
void ath9k_hw_name(struct ath_hw *ah, char *hw_name, size_t len);
/* HTC */
void ath9k_hw_htc_resetinit(struct ath_hw *ah);
/* PHY */
void ath9k_hw_get_delta_slope_vals(struct ath_hw *ah, u32 coef_scaled,
u32 *coef_mantissa, u32 *coef_exponent);
/*
* Code Specific to AR5008, AR9001 or AR9002,
* we stuff these here to avoid callbacks for AR9003.
*/
void ar9002_hw_cck_chan14_spread(struct ath_hw *ah);
int ar9002_hw_rf_claim(struct ath_hw *ah);
void ar9002_hw_enable_async_fifo(struct ath_hw *ah);
void ar9002_hw_update_async_fifo(struct ath_hw *ah);
void ar9002_hw_enable_wep_aggregation(struct ath_hw *ah);
/*
* Code specific to AR9003, we stuff these here to avoid callbacks
* for older families
*/
void ar9003_hw_bb_watchdog_config(struct ath_hw *ah);
void ar9003_hw_bb_watchdog_read(struct ath_hw *ah);
void ar9003_hw_bb_watchdog_dbg_info(struct ath_hw *ah);
void ar9003_paprd_enable(struct ath_hw *ah, bool val);
void ar9003_paprd_populate_single_table(struct ath_hw *ah,
struct ath9k_channel *chan, int chain);
int ar9003_paprd_create_curve(struct ath_hw *ah, struct ath9k_channel *chan,
int chain);
int ar9003_paprd_setup_gain_table(struct ath_hw *ah, int chain);
int ar9003_paprd_init_table(struct ath_hw *ah);
bool ar9003_paprd_is_done(struct ath_hw *ah);
void ar9003_hw_set_paprd_txdesc(struct ath_hw *ah, void *ds, u8 chains);
/* Hardware family op attach helpers */
void ar5008_hw_attach_phy_ops(struct ath_hw *ah);
void ar9002_hw_attach_phy_ops(struct ath_hw *ah);
void ar9003_hw_attach_phy_ops(struct ath_hw *ah);
void ar9002_hw_attach_calib_ops(struct ath_hw *ah);
void ar9003_hw_attach_calib_ops(struct ath_hw *ah);
void ar9002_hw_attach_ops(struct ath_hw *ah);
void ar9003_hw_attach_ops(struct ath_hw *ah);
/*
* ANI work can be shared between all families but a next
* generation implementation of ANI will be used only for AR9003 only
* for now as the other families still need to be tested with the same
ath9k: add new ANI implementation for AR9003 This adds support for ANI for AR9003. The implementation for ANI for AR9003 is slightly different than the one used for the older chipset families. It can technically be used for the older families as well but this is not yet fully tested so we only enable the new ANI for the AR5008, AR9001 and AR9002 families with a module parameter, force_new_ani. The old ANI implementation is left intact. Details of the new ANI implemention: * ANI adjustment logic is now table driven so that each ANI level setting is parameterized. This makes adjustments much more deterministic than the old procedure based logic and allows adjustments to be made incrementally to several parameters per level. * ANI register settings are now relative to INI values; so ANI param zero level == INI value. Appropriate floor and ceiling values are obeyed when adjustments are combined with INI values. * ANI processing is done once per second rather that every 100ms. The poll interval is now a set upon hardware initialization and can be picked up by the core driver. * OFDM error and CCK error processing are made in a round robin fashion rather than allowing all OFDM adjustments to be made before CCK adjustments. * ANI adjusts MRC CCK off in the presence of high CCK errors * When adjusting spur immunity (SI) and OFDM weak signal detection, ANI now sets register values for the extension channel too * When adjusting FIR step (ST), ANI now sets register for FIR step low too * FIR step adjustments now allow for an extra level of immunity for extremely noisy environments * The old Noise immunity setting (NI), which changes coarse low, size desired, etc have been removed. Changing these settings could affect up RIFS RX as well. * CCK weak signal adjustment is no longer used * ANI no longer enables phy error interrupts; in all cases phy hw counting registers are used instead * The phy error count (overflow) interrupts are also no longer used for ANI adjustments. All ANI adjustments are made via the polling routine and no adjustments are possible in the ISR context anymore * A history settings buffer is now correctly used for each channel; channel settings are initialized with the defaults but later changes are restored when returning back to that channel * When scanning, ANI is disabled settings are returned to (INI) defaults. * OFDM phy error thresholds are now 400 & 1000 (errors/second units) for low/high water marks, providing increased stability/hysteresis when changing levels. * Similarly CCK phy error thresholds are now 300 & 600 (errors/second) Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-12 12:33:45 +08:00
* next generation ANI. Feel free to start testing it though for the
* older families (AR5008, AR9001, AR9002) by using modparam_force_new_ani.
*/
ath9k: add new ANI implementation for AR9003 This adds support for ANI for AR9003. The implementation for ANI for AR9003 is slightly different than the one used for the older chipset families. It can technically be used for the older families as well but this is not yet fully tested so we only enable the new ANI for the AR5008, AR9001 and AR9002 families with a module parameter, force_new_ani. The old ANI implementation is left intact. Details of the new ANI implemention: * ANI adjustment logic is now table driven so that each ANI level setting is parameterized. This makes adjustments much more deterministic than the old procedure based logic and allows adjustments to be made incrementally to several parameters per level. * ANI register settings are now relative to INI values; so ANI param zero level == INI value. Appropriate floor and ceiling values are obeyed when adjustments are combined with INI values. * ANI processing is done once per second rather that every 100ms. The poll interval is now a set upon hardware initialization and can be picked up by the core driver. * OFDM error and CCK error processing are made in a round robin fashion rather than allowing all OFDM adjustments to be made before CCK adjustments. * ANI adjusts MRC CCK off in the presence of high CCK errors * When adjusting spur immunity (SI) and OFDM weak signal detection, ANI now sets register values for the extension channel too * When adjusting FIR step (ST), ANI now sets register for FIR step low too * FIR step adjustments now allow for an extra level of immunity for extremely noisy environments * The old Noise immunity setting (NI), which changes coarse low, size desired, etc have been removed. Changing these settings could affect up RIFS RX as well. * CCK weak signal adjustment is no longer used * ANI no longer enables phy error interrupts; in all cases phy hw counting registers are used instead * The phy error count (overflow) interrupts are also no longer used for ANI adjustments. All ANI adjustments are made via the polling routine and no adjustments are possible in the ISR context anymore * A history settings buffer is now correctly used for each channel; channel settings are initialized with the defaults but later changes are restored when returning back to that channel * When scanning, ANI is disabled settings are returned to (INI) defaults. * OFDM phy error thresholds are now 400 & 1000 (errors/second units) for low/high water marks, providing increased stability/hysteresis when changing levels. * Similarly CCK phy error thresholds are now 300 & 600 (errors/second) Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-12 12:33:45 +08:00
extern int modparam_force_new_ani;
void ath9k_hw_attach_ani_ops_old(struct ath_hw *ah);
ath9k: add new ANI implementation for AR9003 This adds support for ANI for AR9003. The implementation for ANI for AR9003 is slightly different than the one used for the older chipset families. It can technically be used for the older families as well but this is not yet fully tested so we only enable the new ANI for the AR5008, AR9001 and AR9002 families with a module parameter, force_new_ani. The old ANI implementation is left intact. Details of the new ANI implemention: * ANI adjustment logic is now table driven so that each ANI level setting is parameterized. This makes adjustments much more deterministic than the old procedure based logic and allows adjustments to be made incrementally to several parameters per level. * ANI register settings are now relative to INI values; so ANI param zero level == INI value. Appropriate floor and ceiling values are obeyed when adjustments are combined with INI values. * ANI processing is done once per second rather that every 100ms. The poll interval is now a set upon hardware initialization and can be picked up by the core driver. * OFDM error and CCK error processing are made in a round robin fashion rather than allowing all OFDM adjustments to be made before CCK adjustments. * ANI adjusts MRC CCK off in the presence of high CCK errors * When adjusting spur immunity (SI) and OFDM weak signal detection, ANI now sets register values for the extension channel too * When adjusting FIR step (ST), ANI now sets register for FIR step low too * FIR step adjustments now allow for an extra level of immunity for extremely noisy environments * The old Noise immunity setting (NI), which changes coarse low, size desired, etc have been removed. Changing these settings could affect up RIFS RX as well. * CCK weak signal adjustment is no longer used * ANI no longer enables phy error interrupts; in all cases phy hw counting registers are used instead * The phy error count (overflow) interrupts are also no longer used for ANI adjustments. All ANI adjustments are made via the polling routine and no adjustments are possible in the ISR context anymore * A history settings buffer is now correctly used for each channel; channel settings are initialized with the defaults but later changes are restored when returning back to that channel * When scanning, ANI is disabled settings are returned to (INI) defaults. * OFDM phy error thresholds are now 400 & 1000 (errors/second units) for low/high water marks, providing increased stability/hysteresis when changing levels. * Similarly CCK phy error thresholds are now 300 & 600 (errors/second) Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-12 12:33:45 +08:00
void ath9k_hw_attach_ani_ops_new(struct ath_hw *ah);
#define ATH_PCIE_CAP_LINK_CTRL 0x70
#define ATH_PCIE_CAP_LINK_L0S 1
#define ATH_PCIE_CAP_LINK_L1 2
#define ATH9K_CLOCK_RATE_CCK 22
#define ATH9K_CLOCK_RATE_5GHZ_OFDM 40
#define ATH9K_CLOCK_RATE_2GHZ_OFDM 44
#define ATH9K_CLOCK_FAST_RATE_5GHZ_OFDM 44
#endif