mirror of https://gitee.com/openkylin/linux.git
dt-bindings: i2c: stm32: Migrate i2c-stm32 documentation to yaml
The document was migrated to Yaml format and renamed st,stm32-i2c.yaml Signed-off-by: Alain Volmat <alain.volmat@st.com> Signed-off-by: Rob Herring <robh@kernel.org>
This commit is contained in:
parent
1e25c5f533
commit
f33dabf59d
|
@ -1,65 +0,0 @@
|
|||
* I2C controller embedded in STMicroelectronics STM32 I2C platform
|
||||
|
||||
Required properties:
|
||||
- compatible: Must be one of the following
|
||||
- "st,stm32f4-i2c"
|
||||
- "st,stm32f7-i2c"
|
||||
- reg: Offset and length of the register set for the device
|
||||
- interrupts: Must contain the interrupt id for I2C event and then the
|
||||
interrupt id for I2C error.
|
||||
- resets: Must contain the phandle to the reset controller.
|
||||
- clocks: Must contain the input clock of the I2C instance.
|
||||
- A pinctrl state named "default" must be defined to set pins in mode of
|
||||
operation for I2C transfer
|
||||
- #address-cells = <1>;
|
||||
- #size-cells = <0>;
|
||||
|
||||
Optional properties:
|
||||
- clock-frequency: Desired I2C bus clock frequency in Hz. If not specified,
|
||||
the default 100 kHz frequency will be used.
|
||||
For STM32F4 SoC Standard-mode and Fast-mode are supported, possible values are
|
||||
100000 and 400000.
|
||||
For STM32F7, STM32H7 and STM32MP1 SoCs, Standard-mode, Fast-mode and Fast-mode
|
||||
Plus are supported, possible values are 100000, 400000 and 1000000.
|
||||
- dmas: List of phandles to rx and tx DMA channels. Refer to stm32-dma.txt.
|
||||
- dma-names: List of dma names. Valid names are: "rx" and "tx".
|
||||
- i2c-scl-rising-time-ns: I2C SCL Rising time for the board (default: 25)
|
||||
For STM32F7, STM32H7 and STM32MP1 only.
|
||||
- i2c-scl-falling-time-ns: I2C SCL Falling time for the board (default: 10)
|
||||
For STM32F7, STM32H7 and STM32MP1 only.
|
||||
I2C Timings are derived from these 2 values
|
||||
- st,syscfg-fmp: Use to set Fast Mode Plus bit within SYSCFG when Fast Mode
|
||||
Plus speed is selected by slave.
|
||||
1st cell: phandle to syscfg
|
||||
2nd cell: register offset within SYSCFG
|
||||
3rd cell: register bitmask for FMP bit
|
||||
For STM32F7, STM32H7 and STM32MP1 only.
|
||||
|
||||
Example:
|
||||
|
||||
i2c@40005400 {
|
||||
compatible = "st,stm32f4-i2c";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <0x40005400 0x400>;
|
||||
interrupts = <31>,
|
||||
<32>;
|
||||
resets = <&rcc 277>;
|
||||
clocks = <&rcc 0 149>;
|
||||
pinctrl-0 = <&i2c1_sda_pin>, <&i2c1_scl_pin>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
i2c@40005400 {
|
||||
compatible = "st,stm32f7-i2c";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <0x40005400 0x400>;
|
||||
interrupts = <31>,
|
||||
<32>;
|
||||
resets = <&rcc STM32F7_APB1_RESET(I2C1)>;
|
||||
clocks = <&rcc 1 CLK_I2C1>;
|
||||
pinctrl-0 = <&i2c1_sda_pin>, <&i2c1_scl_pin>;
|
||||
pinctrl-names = "default";
|
||||
st,syscfg-fmp = <&syscfg 0x4 0x1>;
|
||||
};
|
|
@ -0,0 +1,141 @@
|
|||
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
|
||||
%YAML 1.2
|
||||
---
|
||||
$id: http://devicetree.org/schemas/i2c/st,stm32-i2c.yaml#
|
||||
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
||||
|
||||
title: I2C controller embedded in STMicroelectronics STM32 I2C platform
|
||||
|
||||
maintainers:
|
||||
- Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
|
||||
|
||||
allOf:
|
||||
- $ref: /schemas/i2c/i2c-controller.yaml#
|
||||
- if:
|
||||
properties:
|
||||
compatible:
|
||||
contains:
|
||||
enum:
|
||||
- st,stm32f7-i2c
|
||||
then:
|
||||
properties:
|
||||
i2c-scl-rising-time-ns:
|
||||
default: 25
|
||||
|
||||
i2c-scl-falling-time-ns:
|
||||
default: 10
|
||||
|
||||
st,syscfg-fmp:
|
||||
description: Use to set Fast Mode Plus bit within SYSCFG when
|
||||
Fast Mode Plus speed is selected by slave.
|
||||
Format is phandle to syscfg / register offset within
|
||||
syscfg / register bitmask for FMP bit.
|
||||
allOf:
|
||||
- $ref: "/schemas/types.yaml#/definitions/phandle-array"
|
||||
- items:
|
||||
minItems: 3
|
||||
maxItems: 3
|
||||
|
||||
- if:
|
||||
properties:
|
||||
compatible:
|
||||
contains:
|
||||
enum:
|
||||
- st,stm32f4-i2c
|
||||
then:
|
||||
properties:
|
||||
clock-frequency:
|
||||
enum: [100000, 400000]
|
||||
|
||||
properties:
|
||||
compatible:
|
||||
enum:
|
||||
- st,stm32f4-i2c
|
||||
- st,stm32f7-i2c
|
||||
|
||||
reg:
|
||||
maxItems: 1
|
||||
|
||||
interrupts:
|
||||
items:
|
||||
- description: interrupt ID for I2C event
|
||||
- description: interrupt ID for I2C error
|
||||
|
||||
resets:
|
||||
maxItems: 1
|
||||
|
||||
clocks:
|
||||
maxItems: 1
|
||||
|
||||
dmas:
|
||||
items:
|
||||
- description: RX DMA Channel phandle
|
||||
- description: TX DMA Channel phandle
|
||||
|
||||
dma-names:
|
||||
items:
|
||||
- const: rx
|
||||
- const: tx
|
||||
|
||||
clock-frequency:
|
||||
description: Desired I2C bus clock frequency in Hz. If not specified,
|
||||
the default 100 kHz frequency will be used.
|
||||
For STM32F7, STM32H7 and STM32MP1 SoCs, Standard-mode,
|
||||
Fast-mode and Fast-mode Plus are supported, possible
|
||||
values are 100000, 400000 and 1000000.
|
||||
default: 100000
|
||||
enum: [100000, 400000, 1000000]
|
||||
|
||||
required:
|
||||
- compatible
|
||||
- reg
|
||||
- interrupts
|
||||
- resets
|
||||
- clocks
|
||||
|
||||
examples:
|
||||
- |
|
||||
#include <dt-bindings/mfd/stm32f7-rcc.h>
|
||||
#include <dt-bindings/clock/stm32fx-clock.h>
|
||||
//Example 1 (with st,stm32f4-i2c compatible)
|
||||
i2c@40005400 {
|
||||
compatible = "st,stm32f4-i2c";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <0x40005400 0x400>;
|
||||
interrupts = <31>,
|
||||
<32>;
|
||||
resets = <&rcc 277>;
|
||||
clocks = <&rcc 0 149>;
|
||||
};
|
||||
|
||||
//Example 2 (with st,stm32f7-i2c compatible)
|
||||
i2c@40005800 {
|
||||
compatible = "st,stm32f7-i2c";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <0x40005800 0x400>;
|
||||
interrupts = <31>,
|
||||
<32>;
|
||||
resets = <&rcc STM32F7_APB1_RESET(I2C1)>;
|
||||
clocks = <&rcc 1 CLK_I2C1>;
|
||||
};
|
||||
|
||||
//Example 3 (with st,stm32f7-i2c compatible on stm32mp)
|
||||
#include <dt-bindings/interrupt-controller/arm-gic.h>
|
||||
#include <dt-bindings/clock/stm32mp1-clks.h>
|
||||
#include <dt-bindings/reset/stm32mp1-resets.h>
|
||||
i2c@40013000 {
|
||||
compatible = "st,stm32f7-i2c";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <0x40013000 0x400>;
|
||||
interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
|
||||
clocks = <&rcc I2C2_K>;
|
||||
resets = <&rcc I2C2_R>;
|
||||
i2c-scl-rising-time-ns = <185>;
|
||||
i2c-scl-falling-time-ns = <20>;
|
||||
st,syscfg-fmp = <&syscfg 0x4 0x2>;
|
||||
};
|
||||
...
|
Loading…
Reference in New Issue