Even though the binding claims that the frequency can go up to 6MHz, the
common i2c binding sets a limit at 3MHz, which then triggers a warning.
Since the only SoC that uses that bus uses a frequency of 100kHz, and that
this bus hasn't been found in an SoC for something like 5 years, let's just
fix the example to have a frequency within the acceptable range for i2c.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
One example has a compatible that isn't a valid combination according to
the binding, and now that the examples are validated as well, this
generates a warning.
Let's fix this.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c-i801 driver documentation needs some dusting:
* Mention disable_features flag 0x20.
* The i2c_ec driver has been removed from the kernel long ago. Driver
i2c-scmi serves the same purpose for more recent hardware.
* Replace obsolete /proc paths with equivalent /sys paths.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add SMBUS PCI ID for Intel Tiger Lake -LP.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I managed to break sorting in PCI ID defines in my last two patches:
commit 5cd1c56c42 ("i2c: i801: Add support for Intel Comet Lake")
commit 9be1485acc ("i2c: i801: Add support for Intel Elkhart Lake")
Fix them up.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add missing documentation for "dmas" and "dma-names" properties that can be
used on i2c-stm32.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds the support of I2C_SMBUS_I2C_BLOCK_DATA transaction type
for the stm32f7 SMBUS Controller.
Use emulated I2C_SMBUS_I2C_BLOCK_DATA transactions as there is no specific
hardware in STM32 I2C to manage this (e.g. like no need for PEC here).
Emulated transfer will fall back calling i2c transfer method where there's
already support for DMAs for example.
So, use the I2C_FUNC_SMBUS_I2C_BLOCK in stm32f7_i2c_func(), and rely on
emulated transfer by returning -EOPNOTSUPP in the smbus_xfer() routine
for such a case.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Only set init_irq during i2c_device_new and only handle client->irq on
the probe/remove paths.
Suggested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It makes sense to contain all the ACPI IRQ handling in a single helper
function.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Bring the ACPI path in sync with the device tree path and handle all the
IRQ fetching at probe time. This leaves the only IRQ handling at device
registration time being that which is passed directly through the board
info as either a resource or an actual IRQ number.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In preparation for future refactoring factor out the fetch of the IRQ
into its own helper function. Whilst we are at it update the handling
to return the actual error code returned from acpi_dev_get_resources
as well.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use the available IRQ helper functions, most of the functions have
additional helpful side affects like configuring the trigger type of the
IRQ.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove the static from i2c_dev_irq_from _resources so that other parts
of the core code can use this helper function.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I realize that there are changes in drivers/i2c/busses/i2c-i801.c that strictly
speaking don't belong here, but I hope you don't mind. These changes are all
about the interaction with the i2c-mux-gpio code, and I did a test-merge a few
days ago w/o conflicts.
Anyway, the GPIO-work from Linus Walleij (with help from Serge Semin) in the
i2c-mux-gpio and i2c-arb-gpio-challenge drivers is the main feature.
- simplify the probing code by using devm_i2c_new_dummy_device()
- simplify the code further by moving the code around a bit
- use struct_size() instead of calculating the required structure size
by hand
- remove any references to now removed platform data from comments
-----BEGIN PGP SIGNATURE-----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=4kIu
-----END PGP SIGNATURE-----
Merge tag 'at24-v5.3-updates-for-wolfram' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into i2c/for-5.3
at24: updates for v5.3
- simplify the probing code by using devm_i2c_new_dummy_device()
- simplify the code further by moving the code around a bit
- use struct_size() instead of calculating the required structure size
by hand
- remove any references to now removed platform data from comments
We no longer have platform data in at24, so this comment is invalid.
Make it refer to device tree & properties instead.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
J721E SoCs have same I2C IP as OMAP SoCs. Add new compatible to
handle J721E SoCs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Switch the DT binding to a YAML schema to enable the DT validation.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Switch the DT binding to a YAML schema to enable the DT validation.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds a driver for the I2C controller found on the MediaTek
MT7621/7628/7688 SoC's. The base version of this driver was done by
Steven Liu (according to the copyright and MODULE_AUTHOR lines). It
can be found in the OpenWRT repositories (v4.14 at the time I looked).
The base driver had many issues, which are disccussed here:
https://en.forum.labs.mediatek.com/t/openwrt-15-05-loads-non-working-i2c-kernel-module-for-mt7688/1286/3
>From this link an enhanced driver version (complete rewrite, mayor
changes: support clock stretching, repeated start, ACK handling and
unlimited message length) from Jan Breuer can be found here:
https://gist.github.com/j123b567/9b555b635c2b4069d716b24198546954
This patch now adds this enhanced I2C driver to mainline.
Changes by Stefan Roese for upstreaming:
- Add devicetree bindings
- checkpatch clean
- Use module_platform_driver()
- Minor cosmetic enhancements
- Removed IO warpped functions
- Use readl_relaxed_poll_timeout() and drop poll_down_timeout()
- Removed superfluous barrier() in mtk_i2c_reset()
- Use i2c_8bit_addr_from_msg()
- Added I2C_FUNC_PROTOCOL_MANGLING
- Removed adap->class = I2C_CLASS_HWMON | I2C_CLASS_SPD;
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add bindings for the I2C controller that can be found in the MediaTek
MT7621/7628/7688 SoCs.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We are using sysfs functions directly, so we should include the header.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Probe function fails to recognize that upstream clock actually
doesn't yet exist because clock driver has not been initialized.
Actually try to go get the clock and test for its existence
before trying to set up a downstream clock based upon it.
This fixes a bug that causes the i2c driver not to work with
monolithic kernels.
Fixes: bebff81fb8 ("i2c: bcm2835: Model Divider in CCF")
Signed-off-by: Annaliese McDermond <nh6z@nh6z.net>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If any of the clock code in the probe fails and returns, the IRQ
will not be freed. Moving the IRQ request to last allows it to
be freed on any errors further up in the probe function. devm_
calls can apparently not be used because there are some potential
race conditions that will arise.
Fixes: bebff81fb8 ("i2c: bcm2835: Model Divider in CCF")
Signed-off-by: Annaliese McDermond <nh6z@nh6z.net>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Nobody (including me) noticed that these functions were exported but not
added to the header :/
Fixes: 7159dbdae3 ("i2c: core: improve return value handling of i2c_new_device and i2c_new_dummy")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use my commercial address, not my community one.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
[Removed a misplaced newline. /Peter]
Signed-off-by: Peter Rosin <peda@axentia.se>
We are using sysfs functions directly, so we should include the header.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
This switches the i801 GPIO mux to use GPIO descriptors for
handling the GPIO lines. The previous hack which was reaching
inside the GPIO chips etc cannot live on. We pass descriptors
along with the GPIO mux device at creation instead.
The GPIO mux was only used by way of platform data with a
platform device from one place in the kernel: the i801 i2c bus
driver. Let's just associate the GPIO descriptor table with
the actual device like everyone else and dynamically create
a descriptor table passed along with the GPIO i2c mux.
This enables simplification of the GPIO i2c mux driver to
use only the descriptor API and the OF probe path gets
simplified in the process.
The i801 driver was registering the GPIO i2c mux with
PLATFORM_DEVID_AUTO which would make it hard to predict the
device name and assign the descriptor table properly, but
this seems to be a mistake to begin with: all of the
GPIO mux devices are hardcoded to look up GPIO lines from
the "gpio_ich" GPIO chip. If there are more than one mux,
there is certainly more than one gpio chip as well, and
then we have more serious problems. Switch to
PLATFORM_DEVID_NONE instead. There can be only one.
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Jean Delvare <jdelvare@suse.com>
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[Removed a newline, suggested by Andy. /Peter]
Signed-off-by: Peter Rosin <peda@axentia.se>
The usage of BUG() macro is generally discouraged in kernel, unless
it's a problem that results in a physical damage or loss of data.
This patch removes unnecessary BUG() macros and replaces the rest
with warning.
Signed-off-by: Bitan Biswas <bbiswas@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add PCI ID for Intel Elkhart Lake PCH.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
During probe, return the "get_irq" error value instead of -EINVAL which
allows the driver to be deferred probed if needed.
Fix also the case where of_irq_get() returns a negative value.
Note :
On failure of_irq_get() returns 0 or a negative value while
platform_get_irq() returns a negative value.
Fixes: aeb068c572 ("i2c: i2c-stm32f7: add driver")
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
match_string() returns the array index of a matching string.
Use it instead of the open-coded implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add a match table to allow automatic probing of ACPI device
QCOM0220. Ignore clock attainment errors. Set default clock
frequency value.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Qualcomm Geni I2C driver currently probes silently which can be
confusing when debugging potential issues. Add a low level (INFO)
print when each I2C controller is successfully initially set-up.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Post suspend I2C registers have power on reset values. Before any
transfer initialize I2C registers to prevent I2C transfer timeout
and implement suspend and resume callbacks needed. Fix below errors
post suspend:
1) Tegra I2C transfer timeout during jetson tx2 resume:
[ 27.520613] pca953x 1-0074: calling pca953x_resume+0x0/0x1b0 @ 2939, parent: i2c-1
[ 27.633623] tegra-i2c 3160000.i2c: i2c transfer timed out
[ 27.639162] pca953x 1-0074: Unable to sync registers 0x3-0x5. -110
[ 27.645336] pca953x 1-0074: Failed to sync GPIO dir registers: -110
[ 27.651596] PM: dpm_run_callback(): pca953x_resume+0x0/0x1b0 returns -110
[ 27.658375] pca953x 1-0074: pca953x_resume+0x0/0x1b0 returned -110 after 127152 usecs
[ 27.666194] PM: Device 1-0074 failed to resume: error -110
2) Tegra I2C transfer timeout error on jetson Xavier post resume.
Remove i2c bus lock-unlock calls in resume callback as i2c_mark_adapter_*
(suspended-resumed) help ensure i2c core calls from client are not
executed before i2c-tegra resume.
Signed-off-by: Bitan Biswas <bbiswas@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update kerneldoc for i2c client flags because they increased over time.
Also, move them to a position where they can be more easily found.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Much better to read and understand. Naming for i2c_adapter is not
consistent (yet), so use the name which is also used in core code.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c-ocore driver already has a polling mode interface.But it needs
a workaround for FU540 Chipset on HiFive unleashed board (RevA00).
There is an erratum in FU540 chip that prevents interrupt driven i2c
transfers from working, and also the I2C controller's interrupt bit
cannot be cleared if set, due to this the existing i2c polling mode
interface added in mainline earlier doesn't work, and CPU stall's
infinitely, when-ever i2c transfer is initiated.
Ref:
commit dd7dbf0eb0 ("i2c: ocores: refactor setup for polling")
The workaround / fix under OCORES_FLAG_BROKEN_IRQ is particularly for
FU540-COOO SoC.
The polling function identifies a SiFive device based on the device node
and enables the workaround.
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update device id table for Opencore's I2C master based re-implementation
used in FU540-c000 chipset on HiFive Unleashed platform.
Device ID's include Sifive, soc-specific device for chip specific tweaks
and sifive IP block specific device for generic programming model.
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reformatted compatibility strings to one valid combination on
each line.
Add FU540-C000 specific device tree bindings to already available
i2-ocores file. This device is available on
HiFive Unleashed Rev A00 board. Move interrupt under optional
property list as this can be optional.
The FU540-C000 SoC from sifive, has an Opencore's I2C block
reimplementation.
The DT compatibility string for this IP is present in HDL and available at.
https://github.com/sifive/sifive-blocks/blob/master/src/main/scala/devices/i2c/I2C.scala#L73
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the driver defers probe because of a missing clock, avoid outputting
an error message. The clock will show up eventually.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The commit
19b07cb4a1 ("i2c: i801: Register optional lis3lv02d I2C device on Dell machines")
introduced a new check in order to enumerate some slave devices on Dell
machines. Though, it brings a regression on machines where DMI vendor is not set.
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] SMP PTI
CPU: 8 PID: 1 Comm: swapper/0 Not tainted 5.2.0-rc4-next-20190613+ #317
RIP: 0010:strcmp+0xc/0x20
To fix this crash, check if vendor field is present before accessing to it.
Fixes: 19b07cb4a1 ("i2c: i801: Register optional lis3lv02d I2C device on Dell machines")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The IOP3xx has some elaborate code to directly slam the
GPIO lines multiplexed with I2C down low before enablement,
apparently a workaround for a hardware bug found in the
early chips.
After consulting the developer documentation for IOP80321
and IOP80331 I can clearly see that this may be useful for
IOP80321 family (mach-iop32x) but it is highly dubious for
any 80331 series or later chip: in these chips the lines
are not multiplexed for UARTs.
We convert the code to pass optional GPIO descriptors
and register these only on the 80321-based boards where
it makes sense, optionally obtain them in the driver and
use the gpiod_set_raw_value() to ascertain the line gets
driven low when needed.
The GPIO driver does not give the GPIO chip a reasonable
label so the patch also adds that so that these machine
descriptor tables can be used.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The S3C2410 does some funny dance around its pins:
- First try to call back to the platform to get and control
some GPIO pins
- If this doesn't work, it tries to get a pin control handle
- If this doesn't work, it retrieves two GPIOs from the device
tree node and does nothing with them
If we're gonna retrieve two GPIOs and do nothing with them, we
might as well do it using the GPIO descriptor API. When we use
the resource management API, the code gets smaller.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Model the I2C bus clock divider as a part of the Core Clock Framework.
Primarily this removes the clk_get_rate() call from each transfer.
This call causes problems for slave drivers that themselves have
internal clock components that are controlled by an I2C interface.
When the slave's internal clock component is prepared, the prepare
lock is obtained, and it makes calls to the I2C subsystem to
command the hardware to activate the clock. In order to perform
the I2C transfer, this driver sets the divider, which requires
it to get the parent clock rate, which it does with clk_get_rate().
Unfortunately, this function will try to take the clock prepare
lock, which is already held by the slave's internal clock calls
creating a deadlock.
Modeling the divider in the CCF natively removes this dependency
and the divider value is only set upon changing the bus clock
frequency or changes in the parent clock that cascade down to this
divisor. This obviates the need to set the divider with every
transfer and avoids the deadlock described above. It also should
provide better clock debugging and save a few cycles on each
transfer due to not having to recalcuate the divider value.
Signed-off-by: Annaliese McDermond <nh6z@nh6z.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix checkpatch.pl WARNING for delay of approximately 1msec
in flush i2c FIFO polling loop by using usleep_range(1000, 2000):
WARNING: msleep < 20ms can sleep for up to 20ms; see ...
Documentation/timers/timers-howto.txt
+ msleep(1);
Signed-off-by: Bitan Biswas <bbiswas@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Maxime Ripard