BDW caching works differently than the previous generations. Instead of
having bits in the PTE which directly control how the page is cached,
the 3 PTE bits PWT PCD and PAT provide an index into a PAT defined by
register 0x40e0. This style of caching is functionally equivalent to how
it works on HSW and before.
v2: Tiny bikeshed as discussed on internal irc.
v3: Squash in patch from Ville to mirror the x86 PAT setup more like
in arch/x86/mm/pat.c. Primarily, the 0th index will be WB, and not
uncached.
v4: Comment for reason to not use a 64b write on the PPAT.
v5: Add a FIXME comment that the caching bits in the PAT registers
might be wrong due to doc confusion.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The command to emit batch buffers has changed to address 48b addresses.
It seemed reasonable that we could still use the old instruction where
emitting 0 for length would do the right thing, but it seems to bother
the simulator when the code does that.
Now the second dword in the command has the upper 16b of the address of
the batchbuffer.
v2: Remove duplicated vfun assignment.
v3: Squash in VECS support changes from Zhao Yakui <yakui.zhao@intel.com>
v4: Make checkpatch happy.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The interrupt handling implementation remains the same as previous
generations with the 4 types of registers, status, identity, mask, and
enable. However the layout of where the bits go have changed entirely.
To address these changes, all of the interrupt vfuncs needed special
gen8 code.
The way it works is there is a top level status register now which
informs the interrupt service routine which unit caused the interrupt,
and therefore which interrupt registers to read to process the
interrupt. For display the division is quite logical, a set of interrupt
registers for each pipe, and in addition to those, a set each for "misc"
and port.
For GT the things get a bit hairy, as seen by the code. Each of the GT
units has it's own bits defined. They all look *very similar* and
resides in 16 bits of a GT register. As an example, RCS and BCS share
register 0. To compact the code a bit, at a slight expense to
complexity, this is exactly how the code works as well. 2 structures are
added to the ring buffer so that our ring buffer interrupt handling code
knows which ring shares the interrupt registers, and a shift value (ie.
the top or bottom 16 bits of the register).
The above allows us to kept the interrupt register caching scheme, the
per interrupt enables, and the code to mask and unmask interrupts
relatively clean (again at the cost of some more complexity).
Most of the GT units mentioned above are command streamers, and so the
symmetry should work quite well for even the yet to be implemented rings
which Broadwell adds.
v2: Fixes up a couple of bugs, and is more verbose about errors in the
Broadwell interrupt handler.
v3: fix DE_MISC IER offset
v4: Simplify interrupts:
I totally misread the docs the first time I implemented interrupts, and
so this should greatly simplify the mess. Unlike GEN6, we never touch
the regular mask registers in irq_get/put.
v5: Rebased on to of recent pch hotplug setup changes.
v6: Fixup on top of moving num_pipes to intel_info.
v7: Rebased on top of Egbert Eich's hpd irq handling rework. Also
wired up ibx_hpd_irq_setup for gen8.
v8: Rebase on top of Jani's asle handling rework.
v9: Rebase on top of Ben's VECS enabling for Haswell, where he
unfortunately went OCD on the gt irq #defines. Not that they're still
not yet fully consistent:
- Used the GT_RENDER_ #defines + bdw shifts.
- Dropped the shift from the L3_PARITY stuff, seemed clearer.
- s/irq_refcount/irq_refcount.gt/
v10: Squash in VECS enabling patches and the gen8_gt_irq_handler
refactoring from Zhao Yakui <yakui.zhao@intel.com>
v11: Rebase on top of the interrupt cleanups in upstream.
v12: Rebase on top of Ben's DPF changes in upstream.
v13: Drop bdw from the HAS_L3_DPF feature flag for now, it's unclear what
exactly needs to be done. Requested by Ben.
v14: Fix the patch.
- Drop the mask of reserved bits and assorted logic, it doesn't match
the spec.
- Do the posting read inconditionally instead of commenting it out.
- Add a GEN8_MASTER_IRQ_CONTROL definition and use it.
- Fix up the GEN8_PIPE interrupt defines and give the GEN8_ prefixes -
we actually will need to use them.
- Enclose macros in do {} while (0) (checkpatch).
- Clear DE_MISC interrupt bits only after having processed them.
- Fix whitespace fail (checkpatch).
- Fix overtly long lines where appropriate (checkpatch).
- Don't use typedef'ed private_t (maintainer-scripts).
- Align the function parameter list correctly.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v4)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
bikeshed
Just enough to make the code not barf...
Init BDW display to look like HSW. For the simulator this should be
fine, but this will probably require more work.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Add a FIXME comment about RCS flips being untested on bdw.
Also add a note that hblank events are reserved on bdw+ in DERRMR.]
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BDW context sizes varies a bit.
v2: Squash in fixup for the hw context size from Ben.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some VLV PHY/PLL DPIO registers have group/lane/channel access. Current
DPIO register definition doesn't have a structure way to break them
down. As a result it is not easy to match the PHY/PLL registers with the
configdb document. Rename those registers based on the configdb for easy
cross references, and without the need to check the offset in the header
file.
New format is as following.
<platform name>_<DPIO component><optional lane #>_DW<dword # in the
doc>_<optional channel #>
For example,
VLV_PCS_DW0 - Group access to PCS for lane 0 to 3 for PCS DWORD 0.
VLV_PCS01_DW0_CH0 - PCS access to lane 0/1, channel 0 for PCS DWORD 0.
Another example is
VLV_TX_DW0 - Group access to TX lane 0 to 3 for TX DWORD 0
VLV_TX0_DW0 - Refer to TX Lane 0 access only for TX DWORD 0.
There is no functional change on this patch.
v2: Rebase based on previous patch change.
v3: There may be configdb different version that document the start DW
differently. Add a comment to clarify. Fix up some mismatch start DW
for second PLL block. (Ville)
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the connector and pipe passed around, we can now set the backlight
on the right pipe on VLV/BYT.
v2: drop combination mode check for VLV (Jani)
add save/restore code for VLV backlight regs (Jani)
check for existing modulation freq when initializing backlight regs (Jani)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67245
Tested-by: Joe Konno <joe.konno@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV/BYT, we can adjust the CDclk frequency up or down based on the
max pixel clock we need to drive. Lowering it can save power, while
raising it is necessary to support high resolution.
Add a new callback in modeset_affected_pipes and a
modeset_global_resources function to perform this adjustment as
necessary.
v2: use punit interface for 320 and 266 MHz CDclk adjustments (Ville)
v3: reset GMBUS dividers too, since we changed CDclk (Ville)
v4: jump to highest voltage when going to 400MHz CDclk (Jesse)
v5: drop duplicate define (Ville)
use shifts by 1 for fixed point (Ville)
drop new callback (Daniel)
v6: fixup adjusted_mode.clock -> adjusted_mode.crtc_clock again (Ville)
document Bunit reg access better (Ville)
v7: pass modeset_pipes and pipe_config to global_pipes so we get the right
clock data (Ville)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch defines HD-Audio configuration registers and enables display audio
from HDA controller for Valleyview2.
v2: fix missing offset VLV_DISPLAY_BASE
v3: rename patch from 'enable HDMI audio' to 'enable HDA display audio', since
it's for both HDMI and DP audio
v4: use enc_to_dig_port() to get port number, instead of using Haswell specific
function intel_ddi_get_encoder_port()
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I want to merge in the new Broadwell support as a late hw enabling
pull request. But since the internal branch was based upon our
drm-intel-nightly integration branch I need to resolve all the
oustanding conflicts in drm/i915 with a backmerge to make the 60+
patches apply properly.
We'll propably have some fun because Linus will come up with a
slightly different merge solution.
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_drv.c
drivers/gpu/drm/i915/intel_crt.c
drivers/gpu/drm/i915/intel_ddi.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
drivers/gpu/drm/i915/intel_drv.h
All rather simple adjacent lines changed or partial backports from
-next to -fixes, with the exception of the thaw code in i915_dma.c.
That one needed a bit of shuffling to restore the intent.
Oh and the massive header file reordering in intel_drv.h is a bit
trouble. But not much.
v2: Also don't forget the fixup for the silent conflict that results
in compile fail ...
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to reset the DP scrambler on every vsync to get stable CRCs.
And since we can't use the normal pipe CRC on DP ports on g4x we
really need them to be able to test modesetting issues on (e)DP
outputs.
Note that the DC balance reset is for SDVO port CRCs so we don't
strictly need it. But better safe than sorry (and it's a nice template
in case we ever want to grab port CRCs for e.g. audio checking).
v2: Apply the suggestions from Damien's review.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Incorrect definition DPIO_TX3_SWING_CTL4.
From Ville's review: "Based on the specs, the typo meant that HDMI B
ended up using "incorrect" de-emphasis for the TMDS data lanes."
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add comment from Ville's review about the impact.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- Use a for_each_loop and add the corresponding #defines.
- Drop the _ILK postfix on the existing DE_PIPE_VBLANK macro for
consistency with everything else.
- Also use macros (and add the missing one for plane flips) for the
ivb display interrupt handler.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Drop the useless parens that Ville spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The bbstate contains useful bits of debugging information such as
whether the batch is being read from GTT or PPGTT, or whether it is
allowed to execute privileged instructions.
v2: Only record BB_STATE for gen4+
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Production HSW does not need it. I confirmed this with Art.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All our registers which are written through the MCHBAR are defined
descriptively as an offset to the MCHBAR. We had 3 outliers here.
Convert these as well so all registers which are offsets are MCHBAR can
be easily identified/found within the code.
With this, convert DCLK to also follow this format.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Really simple, and we don't even have working frame numbers.
v2: Actually enable it ...
v3: Review from Ville:
- Unconditionally enable the border in the CRC checksum for
consistency with gen3+.
- Handle the "none" source to be able to disable the CRC machinery
again.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The PIPE_B #define was missing the display mmio offset. Use the
_PIPE_INC macro instead, it's simpler.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A bit a mess, since with DP/TV outputs we can't use the pipe CRC.
Also, no plane CRCs, so we need to update the basic testcases.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Should work down to gen2. The #defines for the interrupt sources are
already there in PIPESTAT and are the same on all gmch platforms for
gen2 up to vlv.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Once the machine gets to a certain point in the suspend process, we
expect the GPU to be idle. If it is not, we might corrupt memory.
Empirically (with an early version of this patch) we have seen this is
not the case. We cannot currently explain why the latent GPU writes
occur.
In the technical sense, this patch is a workaround in that we have an
issue we can't explain, and the patch indirectly solves the issue.
However, it's really better than a workaround because we understand why
it works, and it really should be a safe thing to do in all cases.
The noticeable effect other than the debug messages would be an increase
in the suspend time. I have not measure how expensive it actually is.
I think it would be good to spend further time to root cause why we're
seeing these latent writes, but it shouldn't preclude preventing the
fallout.
NOTE: It should be safe (and makes some sense IMO) to also keep the
VALID bit unset on resume when we clear_range(). I've opted not to do
this as properly clearing those bits at some later point would be extra
work.
v2: Fix bugzilla link
Bugzilla: http://bugs.freedesktop.org/show_bug.cgi?id=65496
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=59321
Tested-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Tested-By: Todd Previte <tprevite@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
hw designers decided to change the CRC registers and coalesce them all
into one. Otherwise nothing changed. I've opted for a new hsw_ version
to grab the crc sample since hsw+1 will have the same crc registers,
but different interrupt source registers. So this little helper
function will come handy there.
Also refactor the display error handler with a neat pipe loop.
v2: Use for_each_pipe.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We enable the interrupt unconditionally and only control it
through the enable bit in the CRC control register.
v2: Extract per-platform helpers to compute the register values.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Also add a new _PIPE_INC macro which takes an base plus increment.
Much less likely to botch the job by missing an s/A/B/ somewhere.
v2: They've moved the bitfield. Argh!
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The HDMI audio expects HDMI pixel clock to be set in the audio
configuration. We've currently just set 0, using 25.2 / 1.001 kHz
frequency, which fails with some modes.
v2: Now with a commit message.
Reference: http://mid.gmane.org/CAGpEb3Ep1LRZETPxHGRfBDqr5Ts2tAc8gCukWwugUf1U5NYv1g@mail.gmail.com
Reference: http://mid.gmane.org/20130206213533.GA16367@hardeman.nu
Reported-by: David Härdeman <david@hardeman.nu>
Reported-by: Jasper Smet <josbeir@gmail.com>
Tested-by: Jasper Smet <josbeir@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are several points in the display pipeline where CRCs can be
computed on the bits flowing there. For instance, it's usually possible
to compute the CRCs of the primary plane, the sprite plane or the CRCs
of the bits after the panel fitter (collectively called pipe CRCs).
v2: Quite a bit of rework here and there (Damien)
Signed-off-by: Shuang He <shuang.he@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Fix intermediate compile file reported by Wu Fengguang's
kernel builder.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to be able to use the masks to decode the register contents
regardless of the hardware generation. So just expand the masks to
cover all available bits, even if those are reserved on some
generations.
v2: Don't extend WM1_LP_SR_MASK so far, for the *future*
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Needed to prevent display corruption in high res panels.
v2: use correct unit names (Rodrigo)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Ulrich Drepper <drepper@gmail.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Supposedly VLV uses the CTG+ style frame counter registers instead of
the old gen3/4 style. Add the magic offset to the correct registers.
We should already be taking the correct codepaths for
.get_vblank_counter() and .get_scanout_position().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During system boot up, by default, the power gate for render, media and
display well still power gated. Normally, BIOS will turn off the power
gate. In the BIOS-less system, the driver need to turn off the power
gate very early during driver load.
v2: Move this to intel_uncore_sanitize to allow it to get call during
resume path. (Daniel)
v3: Remove redundant write 0 to DPIO_CTL, and use DPIO_RESET instead of
just 0x1 (Ville)
Add turn of power gate for display 2d/render well/media well.
v4: Remove toggle cmnreset in intel_uncore_sanitize. Cmnreset should
toggle after CRI clock source has been selected. Jesse DPIO reset patch
which toggle the cmnreset in intel_modeset_init_hw() should handle it.
(Ville)
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DPIO needs to have common reset de-asserted on soft resets like boot and
S3. In some cases, the BIOS will have done this for us, but it should
be safe to do at runtime as well, as long as we do it when the pipes are
otherwise off.
v2: update bit name to match docs better (Ville)
reset after CRI clock select (Ville)
References: https://bugs.freedesktop.org/show_bug.cgi?id=69166
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After applying wait-boost we often find ourselves stuck at higher clocks
than required. The current threshold value requires the GPU to be
continuously and completely idle for 313ms before it is dropped by one
bin. Conversely, we require the GPU to be busy for an average of 90% over
a 84ms period before we upclock. So the current thresholds almost never
downclock the GPU, and respond very slowly to sudden demands for more
power. It is easy to observe that we currently lock into the wrong bin
and both underperform in benchmarks and consume more power than optimal
(just by repeating the task and measuring the different results).
An alternative approach, as discussed in the bspec, is to use a
continuous threshold for upclocking, and an average value for downclocking.
This is good for quickly detecting and reacting to state changes within a
frame, however it fails with the common throttling method of waiting
upon the outstanding frame - at least it is difficult to choose a
threshold that works well at 15,000fps and at 60fps. So continue to use
average busy/idle loads to determine frequency change.
v2: Use 3 power zones to keep frequencies low in steady-state mostly
idle (e.g. scrolling, interactive 2D drawing), and frequencies high
for demanding games. In between those end-states, we use a
fast-reclocking algorithm to converge more quickly on the desired bin.
v3: Bug fixes - make sure we reset adj after switching power zones.
v4: Tune - drop the continuous busy thresholds as it prevents us from
choosing the right frequency for glxgears style swap benchmarks. Instead
the goal is to be able to find the right clocks irrespective of the
wait-boost.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Kenneth Graunke <kenneth@whitecape.org>
Cc: Stéphane Marchesin <stephane.marchesin@gmail.com>
Cc: Owen Taylor <otaylor@redhat.com>
Cc: "Meng, Mengmeng" <mengmeng.meng@intel.com>
Cc: "Zhuang, Lena" <lena.zhuang@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise using any atomic memory operation will lock up the GPU due
to a Haswell hardware bug.
v2: Use the _MASKED_BIT_ENABLE macro. Drop drm parameter definition.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: <stable@vger.kernel.org>
[danvet: Fix checkpatch fail.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to use the clock control reg to figure out how many CZ clks are in
30ns and use that as the basis for our RC6 residency calculations.
v2: use ULL everywhere for consistency (Chris)
factor out bias for clarity (Chris)
References: https://bugs.freedesktop.org/show_bug.cgi?id=69692
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And add some reg defines while we're at it. Since the units of the RC6
residency counter are actually in CZ clocks, we want to just use the
high bits or we'll overflow too frequently.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CDCLK is used to generate the gmbus clock. This is normally done by
BIOS. Program the value if the BIOS-less system doesn't do it.
v2: Move this to intel_i2c_reset to allow reprogram the gmbus frequency
during resume. (Daniel)
v3: Change GMBUS_FREQ to GMBUSFREQ_VLV, and use VLV_DISPLAY_BASE.
(Ville).
Remove cdclk_ratio[] table, and calculate the cdclk ratio instead.
(Ville).
Change the shift then mask for reg read, to mask first, then shift.
(Ville).
Remove the gmbus frequency calculation = cdclk/1.01. Based on BIOS
programming, gmbus frequency = cdclk frequency. (Ville)
Add get_disp_clk_div, which can use to get cdclk/czclk divide.
v4: Fix the mmio_offset base for CZCLK_CDCLK_FREQ_RATIO, gmbus_freq
calculation, and duplicate check for gmbus_freq. (Ville)
In VLV, the spec is wrong about 4Mhz reference frequency for GMBUS. It
should be 1Mhz.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
[danvet: Add the comment Ville suggested. Also appease checkpatch a
bit.]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The | operation has higher precedence than "?:" so the macro always
returns GT_RENDER_L3_PARITY_ERROR_INTERRUPT_S1.
This regression has been introduce in "drm/i915: Add second slice l3
remapping".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Future generations will be changing these registers (thanks to design
for giving us an early heads up). To help abstract, create the
definition of the base of the register block, and define all registers
relative to that.
Design has promised to not change the offsets relative to the base.
v2: Also change IS_HASWELL checks to HAS_PSR
CC: Rodrigo Vivi <rodrigo.vivi@gmail.com>
CC: Intel GFX <intel-gfx@lists.freedesktop.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Certain HSW SKUs have a second bank of L3. This L3 remapping has a
separate register set, and interrupt from the first "slice". A slice is
simply a term to define some subset of the GPU's l3 cache. This patch
implements both the interrupt handler, and ability to communicate with
userspace about this second slice.
v2: Remove redundant check about non-existent slice.
Change warning about interrupts of unknown slices to WARN_ON_ONCE
Handle the case where we get 2 slice interrupts concurrently, and switch
the tracking of interrupts to be non-destructive (all Ville)
Don't enable/mask the second slice parity interrupt for ivb/vlv (even
though all docs I can find claim it's rsvd) (Ville + Bryan)
Keep BYT excluded from L3 parity
v3: Fix the slice = ffs to be decremented by one (found by Ville). When
I initially did my testing on the series, I was using 1-based slice
counting, so this code was correct. Not sure why my simpler tests that
I've been running since then didn't pick it up sooner.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
You can't write it using the MCHBAR mirror, the write will just get
dropped.
This should make us BSpec-compliant, but there's no real bug I could
reproduce that is fixed by this patch.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Fix spelling mistake in the comment that Damien spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that adjusted_mode.clock no longer contains the pixel_multiplier, we
can kill the get_clock() callback and instead do the clock readout
in get_pipe_config().
Also i9xx_crtc_clock_get() can now extract the frequency of the PCH
DPLL, so use it to populate port_clock accurately for PCH encoders.
For DP in port A the encoder is still responsible for filling in
port_clock. The FDI adjusted_mode.clock extraction is kept in place
for some extra sanity checking, but we no longer need to pretend it's
also the port_clock.
In the encoder get_config() functions fill out adjusted_mode.clock
based on port_clock and other details such as the DP M/N values,
HDMI 12bpc and SDVO pixel_multiplier. For PCH encoders we will then
do an extra sanity check to make sure the dotclock we derived from
the FDI configuratiuon matches the one we derive from port_clock.
DVO doesn't exist on PCH platforms, so it doesn't need to anything
but assign adjusted_mode.clock=port_clock. And DDI is HSW only, so
none of the changes apply there.
v2: Use hdmi_reg color format to detect 12bpc HDMI case
v3: Set adjusted_mode.clock for LVDS too
v4: Rename ironlake_crtc_clock_get to ironlake_pch_clock_get,
eliminate the useless link_freq variable.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove duplicates, add VLV specific macros for port B and C.
v2: also add PANEL_PORT_SELECT_DPC_VLV for clarity (Ville)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Batchbuffers constructed by userspace can conditionalise their URB
allocations through the use of the MI_SET_PREDICATE command. This
command can read the MI_PREDICATE_RESULT_2 register to see how many
slices are enabled on GT3, and by virtue of the result, scale their
memory allocations to fit enabled memory.
Of course, this only works if the kernel sets the appropriate bit in the
register first.
v2: Better commit subject and message by Chris Wilson.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Credits-to: Yejun Guo <yejun.guo@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2:
- Grab dpio_lock mutex in vlv_enable_dsi_pll().
- Add and call vlv_disable_dsi_pll().
v3: Mostly based on Ville's review comments.
- Only pipe A has DSI PLL lock bit.
- Add more of CCK REG bit definitions for DSI PLL.
- Make tables static.
- Move clock gating out of the clock calculation functions.
- DSI PLL LDO power gating.
- Put alternative MNP from table calc behind #ifdef.
v4: s/CKK/CLK/ in the CCK REG bit definitions (Ville).
Signed-off-by: ymohanma <yogesh.mohan.marimuthu@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add definitions for VLV MIPI DSI registers.
v2: Small fixes per Ville's review comments.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Add comment this is pipe A only (Ville)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For GPIO NC, CCK, CCU, and GPS CORE.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We shouldn't disable the trickle feed bits on Haswell. Our
documentation explicitly says the trickle feed bits of PRI_CTL and
CUR_CTL should not be programmed to 1, and the hardware engineer also
asked us to not program the SPR_CTL field to 1. Leaving the bits as 1
could cause underflows.
Reported-by: Arthur Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Systems with Intel graphics controllers set aside memory exclusively for
gfx driver use. This memory is not always marked in the E820 as
reserved or as RAM, and so is subject to overlap from E820 manipulation
later in the boot process. On some systems, MMIO space is allocated on
top, despite the efforts of the "RAM buffer" approach, which simply
rounds memory boundaries up to 64M to try to catch space that may decode
as RAM and so is not suitable for MMIO.
v2: use read_pci_config for 32 bit reads instead of adding a new one
(Chris)
add gen6 stolen size function (Chris)
v3: use a function pointer (Chris)
drop gen2 bits (Daniel)
v4: call e820_sanitize_map after adding the region
v5: fixup comments (Peter)
simplify loop (Chris)
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66726
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66844
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
RCS flips do work on Iybridge+ so long as we can unmask the messages
through DERRMR. However, there are quite a few workarounds mentioned
regarding unmasking more than one event or triggering more than one
message through DERRMR. Those workarounds in principle prevent us from
performing pipelined flips (and asynchronous flips across multiple
planes) and equally apply to the "known good" BCS ring. Given that it
already appears to work, and also appears to work with unmasking all 3
planes at once (and queuing flips across multiple planes), be brave.
Bugzlla: https://bugs.freedesktop.org/show_bug.cgi?id=67600
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Lightly-tested-by: Stephane Marchesin <marchesin@icps.u-strasbg.fr>
Cc: Stephane Marchesin <marchesin@icps.u-strasbg.fr>
Cc: Ben Widawsky <ben@bwidawsk.net>
Tested-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Alex writes:
This is the radeon drm-next request. Big changes include:
- support for dpm on CIK parts
- support for ASPM on CIK parts
- support for berlin GPUs
- major ring handling cleanup
- remove the old 3D blit code for bo moves in favor of CP DMA or sDMA
- lots of bug fixes
[airlied: fix up a bunch of conflicts from drm_order removal]
* 'drm-next-3.12' of git://people.freedesktop.org/~agd5f/linux: (898 commits)
drm/radeon/dpm: make sure dc performance level limits are valid (CI)
drm/radeon/dpm: make sure dc performance level limits are valid (BTC-SI) (v2)
drm/radeon: gcc fixes for extended dpm tables
drm/radeon: gcc fixes for kb/kv dpm
drm/radeon: gcc fixes for ci dpm
drm/radeon: gcc fixes for si dpm
drm/radeon: gcc fixes for ni dpm
drm/radeon: gcc fixes for trinity dpm
drm/radeon: gcc fixes for sumo dpm
drm/radeonn: gcc fixes for rv7xx/eg/btc dpm
drm/radeon: gcc fixes for rv6xx dpm
drm/radeon: gcc fixes for radeon_atombios.c
drm/radeon: enable UVD interrupts on CIK
drm/radeon: fix init ordering for r600+
drm/radeon/dpm: only need to reprogram uvd if uvd pg is enabled
drm/radeon: check the return value of uvd_v1_0_start in uvd_v1_0_init
drm/radeon: split out radeon_uvd_resume from uvd_v4_2_resume
radeon kms: fix uninitialised hotplug work usage in r100_irq_process()
drm/radeon/audio: set up the sads on DCE3.2 asics
drm/radeon: fix handling of variable sized arrays for router objects
...
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_gem_dmabuf.c
drivers/gpu/drm/i915/intel_pm.c
drivers/gpu/drm/radeon/cik.c
drivers/gpu/drm/radeon/ni.c
drivers/gpu/drm/radeon/r600.c
Need to get my stuff out the door ;-) Highlights:
- pc8+ support from Paulo
- more vma patches from Ben.
- Kconfig option to enable preliminary support by default (Josh
Triplett)
- Optimized cpu cache flush handling and support for write-through caching
of display planes on Iris (Chris)
- rc6 tuning from Stéphane Marchesin for more stability
- VECS seqno wrap/semaphores fix (Ben)
- a pile of smaller cleanups and improvements all over
Note that I've ditched Ben's execbuf vma conversion for 3.12 since not yet
ready. But there's still other vma conversion stuff in here.
* tag 'drm-intel-next-2013-08-23' of git://people.freedesktop.org/~danvet/drm-intel: (62 commits)
drm/i915: Print seqnos as unsigned in debugfs
drm/i915: Fix context size calculation on SNB/IVB/VLV
drm/i915: Use POSTING_READ in lcpll code
drm/i915: enable Package C8+ by default
drm/i915: add i915.pc8_timeout function
drm/i915: add i915_pc8_status debugfs file
drm/i915: allow package C8+ states on Haswell (disabled)
drm/i915: fix SDEIMR assertion when disabling LCPLL
drm/i915: grab force_wake when restoring LCPLL
drm/i915: drop WaMbcDriverBootEnable workaround
drm/i915: Cleaning up the relocate entry function
drm/i915: merge HSW and SNB PM irq handlers
drm/i915: fix how we mask PMIMR when adding work to the queue
drm/i915: don't queue PM events we won't process
drm/i915: don't disable/reenable IVB error interrupts when not needed
drm/i915: add dev_priv->pm_irq_mask
drm/i915: don't update GEN6_PMIMR when it's not needed
drm/i915: wrap GEN6_PMIMR changes
drm/i915: wrap GTIMR changes
drm/i915: add the FCLK case to intel_ddi_get_cdclk_freq
...
With all the common infoframe bits now in place, we can finally write
the vendor specific infoframes in our driver.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Fix the typo introduced in
commit 1a2eb4604b
Author: Keith Packard <keithp@keithp.com>
Date: Wed Nov 16 16:26:07 2011 -0800
drm/i915: Hook up Ivybridge eDP
This fixes eDP link-training failures and cases where all voltage swing
/pre-emphasis levels were tried and failed during clock recovery and -
as a fallback - we go on to do channel equalization with the last voltage
swing/pre-emphasis level which will succeed. Both issues can lead to a
blank screen.
v2:
- improve commit message
CC: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=64880
Tested-by: Jeremy Moles <cubicool@gmail.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All the different context sizes reported in the CXT_SIZE register
aren't meant to be simply added together.
While BSpec is somewhat unclear on the topic of the actual context
size, empirical tests have now revealed the truth. So let's add a
big fat comment to remind people how it all works.
As a result of correctly interpreting CXT_SIZE, the IVB context
size is reduced from three pages to two, while SNB context size
remains at two pages.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On SNB and IVB, there's an MSR (also exposed through MCHBAR) we can use
to read out the amount of energy used over time. Expose this in sysfs
to make it easy to do power comparisons with different configurations.
If the platform supports it, the file will show up under the
drm/card0/power subdirectory of the PCI device in sysfs as gt_energy_uJ.
The value in the file is a running total of energy (in microjoules)
consumed by the graphics device.
v2: move to sysfs (Ben, Daniel)
expose a simple value (Chris)
drop unrelated hunk (Ben)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
v3: by Ben
Tied it into existing rc6 sysfs entries and named that a more generic
"power attrs." Fixed rebase conflicts.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
v4: Since RAPL is a real driver that already exists to serve power
monitoring, place our entry in debugfs. This gives me a fallback
location for systems that do not expose it otherwise.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Whenever I need to work with the HSW_PWER_WELL_* register bits I have
to look at the documentation to find out which bit is to request the
power well and which one shows its current state. Rename the bits so I
won't need to look the docs every time.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After any "soft gfx reset" we must manually invalidate the TLBs
associated with each ring. Empirically, it seems that a
suspend/resume or D3-D0 cycle count as a "soft reset". The symptom is
that the hardware would fail to note the new address for its status
page, and so it would continue to write the shadow registers and
breadcrumbs into the old physical address (now used by something
completely different, scary). Whereas the driver would read the new
status page and never see any progress, it would appear that the GPU
hung immediately upon resume.
Based on a patch by naresh kumar kachhi <naresh.kumar.kacchi@intel.com>
Reported-by: Thiago Macieira <thiago@kde.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=64725
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Thiago Macieira <thiago@kde.org>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Apparently Bspec is wrong in this case here even for gm45. Note that
Bspec is horribly misguided on i965g/gm, so we don't have any other
data points besides that it seems to make machines work better.
With this changes all the bits in PORT_HOTPLUG_STAT for the digital
ports are ordered the same way. This seems to agree with what register
dumps from the hpd storm handling code shows, where the LIVE bit and
the short/long pulse STATUS bits light up at the same time with this
enumeration (but no with the one from Bspec).
Also tested on my gm45 which has two DP+ ports, and everything seems
to still work as expected.
References: http://www.mail-archive.com/intel-gfx@lists.freedesktop.org/msg23054.html
Cc: Egbert Eich <eich@suse.com>
Cc: Jan Niggemann <jn@hz6.de>
Tested-by: Jan Niggemann <jn@hz6.de>
[danvet: Add a big warning that Bspec seems to be wrong for these
bits, suggested by Jani.]
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adjust the current ILK/SNB/IVB watermark codepaths to use the
pre-populated latency values from dev_priv instead of reading
them out from the registers every time.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need the correct clock to accurately assess whether we need to
enable the double wide pipe mode or not.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Stéphane Marchesin <marcheu@chromium.org>
Cc: Stuart Abercrombie <sabercrombie@google.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For now there are no callers, but these functions are going to be
needed for the code that allows Package C8+. Other future features may
also require this code.
Also merge the commit which introduced assert_can_disable_lcpll and
had the following commit message:
Most of the hardware needs to be disabled before LCPLL is disabled, so
let's add a function to assert some of items listed in the "Display
Sequences for LCPLL disabling" documentation.
The idea is that hsw_disable_lcpll should not disable the hardware,
the callers need to take care of calling hsw_disable_lcpll only once
everything is already disabled.
v2: - Rebase.
- Fix D_COMP wait timeout.
v3: - Use wait_for_atomic_use (Ben)
- Remove/add a useless/needed POSTING_READ (Ben)
- Early return in case LCPLL is already restored (Ben)
- Add ndelay(100) (Ben)
v4: - Merge the commit that added assert_can_disable_lcpll (Ben)
- Add interrupt assertions (Ben)
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fix compile fail since there's no HAS_LP_PCH yet.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now it implements 3 different sequences from BSpec and also has
support for ULT.
v2: - Change IS_ULT checks for LPT-LP checks
- Add check for LPT-LP + with_fdi (Ben)
- Merge DBUFF0/GEN0 bit definitions since they're the same
register (Ben)
- DBUFF0 (1<<0) is Disable, not Enable
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The IVB funtions are exactly the same as the ILK ones, with the
exception of the bit register. So add IVB/HSW support to
ironlake_enable_vblank and ironlake_disable_vblank, then kill the
ivybridge functions.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Prefer seq_puts to seq_printf by Paulo Zanoni.
v3: small changes like avoiding calling dp_to_dig_port twice as noticed by
Paulo Zanoni.
v4: Avoiding reading non-existent registers - noticed by Paulo
on first psr debugfs patch.
v5: Accepting more suggestions from Paulo:
* check sw interlace flag instead of i915_read
* introduce PSR_S3D_ENABLED to avoid forgeting it whenever added.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
[danvet: Fix up debugfs output (spotted by Paulo) and rip out the
power well check since we really can't do that in a race-free manner,
so it's bogus.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adding support for PSR Status, PSR entry counter and performance counters.
Heavily based on initial work from Shobhit.
v2: Fix PSR Status Link bits by Paulo Zanoni.
v3: Prefer seq_puts to seq_printf by Paulo Zanoni.
v4: Fix identation by Paulo Zanoni.
v5: Return earlier if it isn't Haswell in order to avoid reading non-existing
registers - by Paulo Zanoni.
CC: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Credits-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adding Enable and Disable PSR functionalities. This includes setting the
PSR configuration over AUX, sending SDP VSC DIP over the eDP PIPE config,
enabling PSR in the sink via DPCD register and finally enabling PSR on
the host.
This patch is based on initial PSR code by Sateesh Kavuri and Kumar Shobhit
but in a different implementation.
v2: * moved functions around and changed its names.
* removed VSC DIP unset from disable.
* remove FBC wa.
* don't mask LSPS anymore.
* incorporate new crtc usage after a rebase.
v3: Make a clear separation between Sink (Panel) and Source (HW) enabling.
v4: Fix identation and other style issues raised by checkpatch (by Paulo).
v5: Changes according to Paulo's review:
static on write_vsc;
avoid using dp_to_dev when already calling dp_to_dig_port;
remove unecessary TP default time setting;
remove unecessary interrupts disabling;
remove unecessary wait_for_vblank when disabling psr;
v6: remove unecessary wait_for_vblank when writing vsc;
v7: adding setup once function to avoid unnecessarily write to vsc
and set debug_ctl every time we enable or disable psr.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Credits-by: Sateesh Kavuri <sateesh.kavuri@intel.com>
Credits-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
[danvet: Apply Paulo's suggestion for unconditionally clearing the
control register when writing the DIP.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The EDRAM present register isn't really defined in the docs. It just
says check to see if it's set to 1. So I haven't defined the 1 value not
knowing what it actually means.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Same treatment as for SERR_INT: If we clear only the bit for the pipe
we're enabling (but unconditionally) then we can always check for
possible underruns after having disabled the interrupt. That way pipe
underruns won't be lost, but at worst only get reported in a delayed
fashion.
v2: The same logic bug as in the SERR handling change also existed
here. The same bugfix of only reporting missed underruns when the
error interrupt was masked applies, too.
v3: Do the same fixes as for the SERR handling that Paulo suggested in
his review:
- s/%i/%c/ fix in the debug output
- move the DE_ERR_INT_IVB read into the respective if block
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fix up the checkpatch bikeshed Paulo noticed.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The current code won't report any fifo underruns on cpt if just one
pipe has fifo underrun reporting disabled. We can't enable the
interrupts, but we can still check the per-transcoder bits and so
report the underrun delayed if:
- We always clear the transcoder's bit (and none of the other bits)
when enabling.
- We check the transcoder's bit after disabling (to avoid racing with
the interrupt handler).
v2: I've forgotten to actually remove the old SERR_INT clearing.
v3: Use transcoder_name as suggested by Paulo Zanoni. Paulo also
noticed a logic bug: When an underrun interrupt fires we report it
both in the interrupt handler and when checking for underruns when
disabling it in cpt_set_fifo_underrun_reporting. But that second check
is only required if the interrupt is disabled and we're switching of
underrun reporting (e.g. because we're disabling the crtc). Hence
check for that condition.
At first I wanted to rework the code to pass that bit of information
from the uppper functions down to cpt_set_fifo_underrun_reporting. But
that turned out too messy. Hence the quick&dirty check whether the
south error interrupt source is masked off or not.
v4: Streamline the control flow a bit.
v5: s/pipe/pch transcoder/ in the dmesg output, suggested by Paulo.
v6: Review from Paulo:
- Reorder the was_enabled assignment to only read the register when we
need it. Also add a comment that we need to do that before updating
the register.
- s/%i/%c/ fix for the debug output.
- Fix the checkpath complaint in the SERR_INT_TRANS_FIFO_UNDERRUN
#define.
v7: Hopefully put that elusive SERR hunk back into this patch, spotted
by Paulo.
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I've missed that intel_dvo_mode_set changes the dpll configuration.
Hence when I've reworked the sequence to only enable the dpll in the
crtc_enable callback in
commit 66e3d5c099
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun Jun 16 21:24:16 2013 +0200
drm/i915: move i9xx dpll enabling into crtc enable function
that special DVO bit was lost. Some BSpec reading confirms that it's
only needed for DVO encoders. Section 1.5.4, "DPLL A Control Register"
for bit 30:
"2X Clock Enable. When driving In non-gang DVO modes such as a
connected flat panel or TV, a 2X" version of the clock is needed. When
not using the 2X output it should be disabled. This bit cannot be set
when driving the integrated LVDS port on devices such as Montara-GM."
Fix this regression up.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66516
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Partially-tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use wait_for() instead of the open coded loop to avoid spreading the
same old timeout related bugs.
This changes the loop to use msleep(1) instead of udelay(10) when the
Punit had not yet completed the frequency change. In practice that
doesn't seem to hurt performance as the Punit appears to be ready pretty
much always.
Also give the status bit a name, instead of using the magic number 1.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With updates to the spec, we can actually see the context layout, and
how many dwords are allocated. That table suggests we need 70720 bytes
per HW context. Rounded up, this is 18 pages. Looking at what lives
after the current 4 pages we use, I can't see too much important (mostly
it's d3d related), but there are a couple of things which look scary. I
am hopeful this can explain some of our odd HSW failures.
v2: Make the context only 17 pages. The power context space isn't used
ever, and execlists aren't used in our driver, making the actual total
66944 bytes.
v3: Add a comment to the code. (Jesse & Paulo)
Reported-by: "Azad, Vinit" <vinit.azad@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We forgot to add VLV_DISPLAY_BASE to the VLV sprite registers, which
caused the sprites to not work at all.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
LPF is short for "low pass filter".
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bspec seems to be full of lies, at least it disagress with reality:
Two systems corrobated that SDVO hpd bits are the same as on gen3.
v2: Update comment a bit.
Cc: Arthur Ranyan <arthur.j.runyan@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Alex Fiestas <afiestas@kde.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=58405
Cc: stable@vger.kernel.org
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Again we don't really support different settings, so don't let the
BIOS sneak stuff through.
Since the motivation for this patch series is to ensure we have the
correct gamma table mode selected also add the required write to the
GAMMA_MODE register to select the 8bit legacy table.
And since I find lowercase letters in #defines offensive, also
bikeshed those.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The specs are a bit unclear whether the per-plane trickle feed disable
control exists on VLV. There is another trickle feed disable control
in the MI_ARB register.
After some experimentation it turns out both the DSPCNTR trickle feed
bits and the MI_ARB bit can be toggled. However the DSPCNTR bits don't
seem to have any effect.
The MI_ARB bit, on the other hand, has a noticable effect. I performed
an experiment where I reduced the FIFO size via DSPARB and observed the
effect of the MI_ARB trickle feed bit on the display.
Using a 1920x1080-60 mode, with MI_ARB=0x4 the display started to have
problems with DSPARB=0x42424242, whereas with MI_ARB=0x0 the problems
didn't start until DSPARB=0x09090909. This seems to confirm that the
MI_ARB trickle feed bit actually does work.
So replace the use of the DSPCNTR trickle feed bits with MI_ARB
on VLV.
v2: Amend commit message with results from experimentation
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Using ids in register macros is much more common in our driver. Also
this way we can reduce the platform specific stuff a bit.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The bits are evenly space, so we can cut down on two big switch
blocks. This also greatly simplifies the hw state readout which
follows in the next patch.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
WaFbcNukeOn3DBlt for IVB, HSW.
According BSPec: "Workaround: Do not enable Render Command Streamer tracking for FBC.
Instead insert a LRI to address 0x50380 with data 0x00000004 after the PIPE_CONTROL that
follows each render submission."
v2: Chris noticed that flush_domains check was missing here and also suggested to do
LRI only when fbc is enabled. To avoid do a I915_READ on every flush lets use the
module parameter check.
v3: Adding Wa name as Damien suggested.
v4: Ville noticed VLV doesn't support fbc at all and comment came wrong from spec.
v5: Ville noticed than on blt a Cache Clean LRI should be used instead the Nuke one.
v6: Check for flush domain on blt (by Ville).
Check for scanout dirty (by Chris).
v7: Apply proper fbc_dirty implemented by Chris.
v8: remove unused variables.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We use port I/O for VGA register access, so adding display_mmio_offset
is just wrong.
This reverts commit 56a12a5092.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix the DSPCLK_GATE_D access for VLV. The code incorrectly tried to
poke at the ILK+ version of the register which is at the wrong offset.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Intermediate Pixel Storage is a feature that should reduce the number
of times the display engine wakes up memory to read pixels, so it
should allow deeper PC states. IPS can only be enabled on ULT pipe A
with 8:8:8 pipe pixel formats.
With eDP 1920x1080 and correct watermarks but without FBC this moves
my PC7 residency from 2.5% to around 38%.
v2: - It's tied to pipe A, not port A
- Add pipe_config support (Chris)
- Add some assertions (Chris)
- Rebase against latest dinq
v3: - Don't ever set ips_enabled to false (Daniel)
- Only check for ips_enabled at hsw_disable_ips (Daniel)
v4: - Add hsw_compute_ips_config (Daniel)
- Use the new dump_pipe_config (Daniel)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similar to a patch originally written by:
v2: Reversed the meanings of masked and enabled (Haihao)
Made non-destructive writes in case enable/disabler rps runs first
(Haihao)
v3: Reword error message (Damien)
Modify postinstall to do the right thing based on previous fixup. (Ben)
CC: Xiang, Haihao <haihao.xiang@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The motivation here is we're going to add some new interrupt definitions
and handling outside of the GT interrupts which is all we've managed so
far (with some RPS exceptions). By consolidating the names in the future
we can make thing a bit cleaner as we don't need to define register
names twice, and we can leverage pretty decent overlap in HW registers
since ILK.
To explain briefly what is in the comments: there are two sets of
interrupt masking/enabling registers. At least so far, the definitions
of the two sets overlap. The old code setup distinct names for
interrupts in each set, ie. one for global, and one for ring. This made
things confusing when using the wrong defines in the wrong places.
rebase: Modified VLV bits
v2: Renamed GT_RENDER_MASTER to GT_RENDER_CS_MASTER (Damien)
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
PM interrupts have an expanded role on HSW. It helps route the EBOX
interrupts. This patch is necessary to make the existing code which
touches the mask, and enable registers more friendly to other code paths
that also will need these registers.
To be more explicit:
At preinstall all interrupts are masked and disabled. This implies that
preinstall should always happen before any enabling/disabling of RPS or
other interrupts.
The PMIMR is touched by the workqueue, so enable/disable touch IER and
IIR. Similarly, the code currently expects IMR has no use outside of the
RPS related interrupts so they unconditionally set 0, or ~0. We could
use IER in the workqueue, and IMR elsewhere, but since the workqueue
use-case is more transient the existing usage makes sense.
Disable RPS events:
IER := IER & ~GEN6_PM_RPS_EVENTS // Disable RPS related interrupts
IIR := GEN6_PM_RPS_EVENTS // Disable any outstanding interrupts
Enable RPS events:
IER := IER | GEN6_PM_RPS_EVENTS // Enable the RPS related interrupts
IIR := GEN6_PM_RPS_EVENTS // Make sure there were no leftover events
(really shouldn't happen)
v2: Shouldn't destroy PMIIR or PMIMR VEBOX interrupt state in
enable/disable rps functions (Haihao)
v3: Bug found by Chris where we were clearing the wrong bits at rps
disable.
expanded commit message
v4: v3 was based off the wrong branch
v5: Added the setting of PMIMR because of previous patch update
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We were previously only setting the WM_PIPE registers, now we are
setting the LP watermark registers. This should allow deeper PC
states, resulting in power savings.
We're only using 1/2 data buffer partitioning for now.
v2: Merge both hsw_compute_pri_wm_* functions (Ville)
v3: - Simplify hsw_compute_wm_results (Ville)
- Rebase due to changes on the previous patch
v4: Unconfuse wm_lp/level (Ville)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We were previously calling sandybridge_update_wm on HSW, but the SNB
function didn't really match the HSW specification, so we were just
writing the wrong values.
With this patch, the haswell_update_wm function will set the correct
values for the WM_PIPE registers, but it will still keep all the LP
watermarks disabled.
The patch may look a little bit over-complicated for now, but it's
because much of the infrastructure for setting the LP watermarks is
already in place, so we won't have too much code churn on the patch
that sets the LP watermarks.
v2: - Fix pixel_rate on panel fitter case (Ville)
- Try to not overflow (Ville)
- Remove useless variable (Ville)
- Fix p->pri_horiz_pixels (Paulo)
v3: - Fix rounding errors on hsw_wm_method2 (Ville)
v4: - Fix memcmp bug (Paulo)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Add set_seqno which didn't exist before rebase (Haihao)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Xiang, Haihao <haihao.xiang@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Like the other rings, the VECS supports semaphores. The semaphore stuff
is a bit wonky so this patch on it's own should be nice for review.
This patch should have no functional impact.
v2: Fix the English parts of clarification (again, register names were
right, text was reversed) (Damien)
Restore the still valid invariant. (Damien)
The bsd semaphore register should be MI_SEMAPHORE_SYNC_VVE (Damien)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This replaces the existing MBOX update code with a more generalized
calculation for emitting mbox updates. We also create a sentinel for
doing the updates so we can more abstractly deal with the rings.
When doing MBOX updates the code must be aware of the /other/ rings.
Until now the platforms which supported semaphores had a fixed number of
rings and so it made sense for the code to be very specialized
(hardcoded).
The patch does contain a functional change, but should have no
behavioral changes.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Semaphores are tied very closely to the rings in the GPU. Trivial patch
adds comments to the existing code so that when we add new rings we can
include comments there as well. It also helps distinguish the ring to
semaphore mailbox interactions by using the ringname in the semaphore
data structures.
This patch should have no functional impact.
v2: The English parts (as opposed to register names) of the comments
were reversed. (Damien)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Both the intel_dpio_{read,write} and valleyview_{punit,nc}_{read,write}
use the IOSF sideband interface. They access the same registers and do
mostly the same stuff, but no shared code. There are even duplicate
register defines for the same registers. Both have locking, but the
former use dpio_lock and the latter rps.hw_lock. It's racy.
This patch refactors the sideband access to a single function that
expects dpio_lock to be held. The dpio_lock is only used for sideband
stuff, so it's a better match than rps.hw_lock for the purpose. The rps
stuff still needs rps.hw_lock, since it's used to protect more than just
the register access, so rps code will need to hold both locks.
Based on the work by Shobhit Kumar <shobhit.kumar@intel.com> and Yogesh
Mohan Marimuthu <yogesh.mohan.marimuthu@intel.com>.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit 1544d9d573 added a workaround
inside haswell_init_clock_gating and mentioned it is "a workaround for
early silicon revisions and should be removed later". This workaround
is documented in bit 31 of PRI_CTL. I asked Arthur and he mentioned
that setting FORCE_ARB_IDLE_PLANES replaces that workaround for the
newer machines. So use the new one.
Also notice that there's still another workaround for PRI_CTL that
involves WM_DBG, but it's not the one we're reverting. And notice that
we were previously setting WM_DBG_DISALLOW_MULTIPIPE_LP which disables
the LP watermarks when more than one pipe is used, and we really don't
want this because we need the LP watermarks if we want to reach deeper
PC states.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add a comment for the w/a name Ville dug out of Bspec.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRmpexAAoJEHm+PkMAQRiGrRIH/1uWFW38RvaCV/PXm/ia6Z+x
BfBJfBIvPxGwb4n7aQNQlhU25xkfrPZ6szO4WiBH5/KPH3xYi2I2OZ1AzffkYqMF
BWkPmsPK6EsTdp16zsi6JtH2aXArG4SpYA7ZamPvDkmfigHuiZg7GlL/9eHTRPNV
P7Q8JToOrcnP8RoGgNj0uFiQeQbc62Kmoq7WuPtUhVlpQCCCknXgOJiYgz9w6Xe9
/i79YFS8WRrzAquExT1NbIOh4ZMqB9MvuroaVWy8JDDLUyz7QUvOCe3tCDNguwgi
FdWvU6nfkdQq5SLaWCWXDE9Rp/pL1MvfBn9vCOwFcp42aw0aQ0PgJVIXvsqufd0=
=jgDI
-----END PGP SIGNATURE-----
Merge tag 'v3.10-rc2' into drm-intel-next-queued
Backmerge Linux 3.10-rc2 since the various (rather trivial) conflicts
grew a bit out of hand. intel_dp.c has the only real functional
conflict since the logic changed while dev_priv->edp.bpp was moved
around.
Also squash in a whitespace fixup from Ben Widawsky for
i915_gem_gtt.c, git seems to do something pretty strange in there
(which I don't fully understand tbh).
Conflicts:
drivers/gpu/drm/i915/i915_reg.h
drivers/gpu/drm/i915/intel_dp.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Display register 46500h bit 23 must be set to 1b for the entire time that
Frame Buffer Compression is enabled.
v2: Ville suggested to enable it back when disabling fbc to avoid wasting
power.
v3: RMW to preserve other bits (by Ville)
v4: Fix from Ville: sed &/| at RMW
v5: Too far on sed.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Insert missing space that checkpatch spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Display register 420B0h bit 22 must be set to 1b for the entire time that
Frame Buffer Compression is enabled.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch introduce Frame Buffer Compression (FBC) support for IVB,
without enabling it by default.
It adds a new function gen7_enable_fbc to avoid getting
ironlake_enable_fbc messed with many IS_IVYBRIDGE checks.
v2: Fixes from Ville.
* Fix Plane. FBC is tied to primary plane A in HSW
* Fix DPFC initial write to avoid let trash on the register.
v3: Checking for bad plane on intel_update_fbc() as Chris suggested.
v4: Ville pointed out that according to BSpec FBC_CTL bits 0:3 must be 0.
v5: Up to v4 this work was entirely focused on Haswell. However Ville
noticed I could reuse the FBC work done for HSW and get FBC for free
at Ivybridge. So it makes more sense enable FBC for IVB first.
FBC for HSW comming on next patches. We are just not enabling it by
default on IVB.
v6: Fix confused commit name (by Matt Turner).
v7: Remove gtt_offset shift since it is page aligned byte offset (by Ville).
Cc: Matt Turner <mattst88@gmail.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
But we need to get the right stolen base and make pre-allocated objects
for BIOS stuff so we don't clobber it. If the BIOS hasn't allocated a
power context, we allocate one here too, from stolen space as required
by the docs.
v2: fix stolen to phys if ladder (Ben)
keep BIOS reserved space out of allocator altogether (Ben)
v3: fix mask of stolen base (Ben)
v4: clean up preallocated object on unload (Ben)
don't zero reg on unload (Jesse)
fix mask harder (Jesse)
v5: use unref for freeing stolen bits (Chris)
move alloc/free to intel_pm.c (Chris)
v6: NULL pctx at disable time so error paths work (Ben)
v7: use correct PCI device for config read (Jesse)
Reviewed-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 03752f5b7b.
This revert requires a bit of explanation on how I understand things
work. Internally the architects/designers decide how the stolen encoding
works. We put it in a doc. BIOS writers take these docs and implement
it. Driver writers read the doc too, and read the value left by the BIOS
writers, and then we make magic.
The failing here is that in the docs we had[1] contained two different
definitions for this register for Gen7. (We have both a PCI register,
and an MMIO, and each of these were different). At the time [2] of
03752f5, we asked the architects what the correct value should be; but
that doesn't match the reality (BIOS) unfortunately.
So on all machines I can get my hands on, this revert is the right thing
to do. I've also worked with the product group to confirm that they
agree this revert is what we should do. People using HW made my "people"
who both write their own BIOS, and have access to our docs (Apple?).
Investigations are still ongoing about whether we need to add a list
of machines needing special handling, but this patch should be the
right thing for pretty much everyone.
[1] The docs are still wrong on this one. Now instead of two registers with
two definitions, we have one register with BOTH definitions, progress?
[2] The open source PRMs have the "wrong" definitions in chapter Volume
1 part6, section 1.1.12.
This digging was inspired by Paulo.
Cc: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Augment the patch saying that it's still a bit unclear
whether there are any machines out there with "wrong" firmware and
whether we need to add a list to handle them specially.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- PCH_ prefix for pch registers on ibx/cpt/ppt.
- Drop the DP_ from the link defines, redundant.
- Drop the GMCH from the data defines and instead give the special g4x
registers a consistent _G4X postfix.
v2:
- Realign #defines and use tabs (Paulo).
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
While at it, also extract a common helper to copy the timings from the
cpu transcoder to the pch transcoder. That way it's really explicit
how the lpt transcoder is hardcoded.
v2:
- Re-align #defines properly (Paulo).
- Use cpu_transcoder when copying pipe timings (Paulo).
- s/intel_pch_transcoder_enable/intel_pch_transcoder_set_timings/
since we already have a pch transcoder enable function, and this is
clearer, too.
- Fixup 80 char line overflow in intel_display.c. I've opted to ignore
this in i915_reg.h and i915_ums.c since meh.
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Every time I read hsw code I get completely confused about this. So
call it what it is more explicitly.
Also, add an LPT_TRANSCONF for the pch transcoder A and use it in
lpt-only code, to really unconfuse me.
v2: s/plane/pipe/ in the TRANSCONF #define (Paulo).
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we ever leak a non-DP compliant port width through here, we have a
pretty serious issue. So just rip out all these WARNs - if we need
them it's probably better to have them at a central place where we
compute the dp lane count.
Also use the new DDI width macro for FDI mode.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: fixup the embarrassing s/intel_dp->DP/temp/ mistake Paulo
spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This does duplicate the logic in intel_crtc_mode_get a bit, but the
issue is that we also should handle interlace modes and other insanity
correctly.
Hence I've opted for a sligthly more elaborate route where we first
read out the crtc timings for the adjusted mode, and then optionally
(not sure if we really need it) compute the modeline from that.
v2: Also read out the pipe source dimensions into the requested mode.
v3: Rebase on top of the moved cpu_transcoder.
v4: Simplify CHECK_FLAGS logic as suggested by Chris Wilson. Also
properly #undef that macro again.
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> (v3)
[danvet: Use the existing mask for interlaced bits, spotted by Mika.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to use the fdi m/n values to easily compute the adjusted mode
dotclock on pch ports. Hence make sure the values stored in the pipe
config are always reliable.
v2: Fixup FDI TU readout.
v3: Rebase on top of moved cpu_transcoder.
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Introduce some nice #defines for the FDI lane width fields and put
them to good use. Suggested by Ville.
v3: Fixup the mask vs. shift copy&pasta fail Imre Deak spotted, and
use the shift #define also in the mask.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Make TRANSCODER_EDP handling more explicit. (Imre)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The BIOS uses power of two values for the data/link N value.
Follow suit to make the Zotac DP to dual-HDMI dongle work.
v2: Clean up the magic numbers and defines
Change the N clamping to be a bit easier on the eye
Rename intel_reduce_ratio to intel_reduce_m_n_ratio
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=49402
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=59810
Tested-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Shame on me for not putting the bit definitions next to the register
definition in the first place.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is bad news and shouldn't be happening.
V2: Rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In this commit we enable both CPU and PCH FIFO underrun reporting and
start reporting them. We follow a few rules:
- after we receive one of these errors, we mask the interrupt, so
we won't get an "interrupt storm" and we also won't flood dmesg;
- at each mode set we enable the interrupts again, so we'll see each
message at most once per mode set;
- in the specific places where we need to ignore the errors, we
completely mask the interrupts.
The downside of this patch is that since we're completely disabling
(masking) the interrupts instead of just not printing error messages,
we will mask more than just what we want on IVB/HSW CPU interrupts
(due to GEN7_ERR_INT) and on CPT/PPT/LPT PCHs (due to SERR_INT). So
when we decide to mask PCH FIFO underruns for pipe A on CPT, we'll
also be masking PCH FIFO underruns for pipe B, because both are
reported by SERR_INT, which has to be either completely enabled or
completely disabled (in othe words, there's no way to disable/enable
specific bits of GEN7_ERR_INT and SERR_INT).
V2: Rename some functions and variables, downgrade messages to
DRM_DEBUG_DRIVER and rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Stolen from a patch with the below impressive sob-section.
Signed-off-by: Pallavi G <pallavi.g@intel.com>
Signed-off-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Gajanan Bhat <gajanan.bhat@intel.com>
Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Drop everything but the header #defines.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Uses slightly different interfaces than other platforms.
v2: track actual set freq, not requested (Rohit)
fix debug prints in init code (Jesse)
v3: don't write sleep reg (Jesse)
re-add RC6 wake limit write (Ben)
fixup thresholds to match other platforms (Ben)
clean up mem freq calculation (Ben)
clean up debug prints (Ben)
v4: move defines from punit patch (Ville)
v5: remove writes to nonexistent regs (Jesse)
put RP and RC regs together (Jesse)
fix RC6 enable (Jesse)
v6: use correct fuse reads from NC (Jesse)
split out min/max funcs for use in sysfs (Jesse)
add debugfs & sysfs freq controls (Jesse)
v7: update with Ben's hw_max changes (Jesse)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> (v6)
[danvet: Follow checkpatch sugggestion to use min_t to avoid casting
fun.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bits 30 and 24:0 are PBC, so don't zero them. Some of the other bits
are being zeroed, but I couldn't find a reason for this, so leave them
as they are for now to avoid regressions.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Delete the redudant #define that Imre spotted in his review.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Check the VBT to see if the machine has inverted FDI RX polarity on
CPT. Based on this bit, set the appropriate bit on the TRANS_CHICKEN2
registers.
This should fix some machines that were showing black screens on all
outputs.
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=60029
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Haswell introduces a separate frequency domain for the ring (uncore). So
where we used to increase the CPU (IA) clock with GPU busyness, we now
need to scale the ring frequency directly instead. As the ring limits
our memory bandwidth, it is vital for performance that when the GPU is
busy, we increase the frequency of the ring to increase the available
memory bandwidth.
v2: Fix the algorithm to actually use the scaled gpu frequency for the ring.
v3: s/max_ring_freq/min_ring_freq/ as that is what it is
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Add space checkpatch complained about.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BSpec contains several scattered notes which state that the maximum
fence stride was increased to 256KB on IVB.
Testing on real hardware agrees.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
IVB and HSW use different encodings for the PPGTT cacheability bits in
the GAM_ECOCHK register.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GAC_ECO_BITS has a bit similar to GAM_ECOCHK's ECOCHK_SNB_BIT. Add
the define, and enable it on SNB.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BIOS should be setting this, but in case it doesn't...
v2: Define the bits we actually want to clear (Jesse)
Make it an RMW op (Jesse)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Slightly different than other platforms.
v2 [Jani]: Fix IOSF_BYTE_ENABLES_SHIFT shift. Use common routine.
v3: drop turbo defines from this patch (Ville)
use PCI_DEVFN(2,0) instead of open coding (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Add checkpatch bikeshed about missing space.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No constant alpha yet though, that needs a new ioctl and/or property to
get/set.
v2: use drm_plane_format_cpp (Ville)
fix up vlv_disable_plane, remove IVB bits (Ville)
remove error path rework (Ville)
fix component order confusion (Ville)
clean up platform init (Ville)
use compute_offset_xtiled (Ville)
v3: fix up more format confusion (Ville)
update to new page offset function (Ville)
v4: remove incorrect formats from framebuffer_init (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Earlier code would leave both bits set, so any reset after the first
would only reset media.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now with Egbert Eich's hpd infrastructure rework merged this is dead
simple. And we need this to make output detection work on SDVO - with
the cleaned-up drm polling helpers outputs which claim to have hpd
support are no longer polled.
Now SDVO claims to do that, but it's not actually wired up. So just do
it.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows to enable HPD interrupts for individual pins to only receive
hotplug events from lines which are connected and working.
v2: Restructured initailization of const arrays following a suggstion
by Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Egbert Eich <eich@suse.de>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to HSW PM programming guide, frequency bits starts at
24 instead of 25.
v2: Paulo Zanoni noticed that only frequency bits can be set at
GEN6_RPNSWREQ. All others are read only.
CC: Ben Widawsky <ben@bwidawsk.net>
CC: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bspec mentions this for HSW+. I can't quite tell what the effects are,
and I don't easily have a way to test this.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We could split this out into a separate routine at some point as an
optimization.
v2: use FORCEWAKE_KERNEL (Ville)
Note: Ville mentioned in his review that he declines to be responsible
if this blows up due to the lack of "readback a register != FW_ACK,
but from the same cacheline" magic we have in other forcewake
implementations.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Bikeshed overtly long lines according to checkpatch.pl. Nope,
this time around I didn't screw up printk message since I've left
those alone.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRRkrbAAoJEHm+PkMAQRiGy3oH/jrbHinYs0auurANgx4TdtWT
/WNajstKBqLOJJ6cnTR7sOqwOVlptt65EbbTs+qGyZ2Z2W/Lg0BMenHvNHo4ER8C
e7UbMdBCSLKBjAMKh1XCoZscGv4Exm8WRH3Vc5yP0Hafj3EzSAVLY1dta9WKKoQi
bh7D1ErUlbU1zczA1w5YbPF0LqFKRvyZOwebMCCAKAxv5wWAxmbcPNxVR4sufkjg
k6TkQ2ysgWivZAfy3tJYOcxiEu7ahpZVEuYdlZEJQXHRQUfoNljQlOp4BqKsYUai
5A0kaf2VpKay/7pkhvTfBBcF/jFJ68pYP6gQ2ThNdr0b5kOiAfMWj030Xyngnhg=
=iO9t
-----END PGP SIGNATURE-----
Merge tag 'v3.9-rc3' into drm-intel-next-queued
Backmerge so that I can merge Imre Deak's coalesced sg entries fixes,
which depend upon the new for_each_sg_page introduce in
commit a321e91b6d
Author: Imre Deak <imre.deak@intel.com>
Date: Wed Feb 27 17:02:56 2013 -0800
lib/scatterlist: add simple page iterator
The merge itself is just two trivial conflicts:
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to set the 'allow force wake' bit to enable forcewake handling
later on.
v2: split from clock gating patch (Jani)
check for allowwakeack (Ville)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Disable bits for ADPA HSYNC and VSYNC where mixed up resulting in suspend
becoming standby and vice versa. Fixed by swapping their bit position.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bits used only on HDMI mode now have HDMI_ prefix instead of SDVO_.
The COLOR_FORMAT bits now have prefixes (and the 12bpc bit is for HDMI
only).
Notice that this patch uncovers a bug on the SDVO code: the
COLOR_RANGE_16_235 bit can only be used if the port is in TMDS mode,
not SDVO mode. This will have to be fixed in a later patch.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since they're all the same register, leave all the #defines at the
same place, organized by Gen and also specify which bits are used by
only a specific port or encoding.
Also remove a few unused duplicates and adjust indentation.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some HDMI registers can be used for SDVO, so saying "HDMIB" should be
the same as saying "SDVOB" for a given HW generation. This was not
true and led to confusions and even a regression.
Previously we had:
- SDVO{B,C} defined as the Gen3+ registers
- HDMI{B,C,D} and PCH_SDVOB defined as the PCH registers
But now:
- SDVO{B,C} became GEN3_SDVO{B,C} on SDVO code
- SDVO{B,C} became GEN4_HDMI{B,C} on HDMI code
- HDMI{B,C,D} became PCH_HDMI{B,C,D}
- PCH_SDVOB is still the same thing
v2: Rebase (v1 was sent in May 2012).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
While old platforms had 3 transcoders and 3 pipes (1:1), HSW has
4 transcoders and 3 pipes.
These regs were being used only by HDMI code where pipe is always the same
thing as cpu_transcoder.
This patch allow us to use them for DP, specially for TRANSCODER_EDP.
v2: Adding HSW_TVIDEO_DIP_VSC_DATA to transmit vsc to eDP.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The indentation is getting way too deep. Pull the vblank interupt
handling out to separate functions.
v2: Keep flip_mask handling in the main irq handler and
flatten {i8xx,i915}_handle_vblank() even further.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We plan to treat GEN7_ERR_INT as an interrupt, so use this register
for the checks inside I915_WRITE. This way we can have the best of
both worlds: the error message with a register address and the
V2: Split in 2 patches: one for the macro, one for changing the
register, as requested by Ben.
V3: Rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
HSW no longer has the PIPECONF bit for limited range RGB output.
Instead the pipe CSC unit must be used to perform that task.
The CSC pre offset are set to 0, since the incoming data is full
[0:255] range RGB, the coefficients are programmed to compress the
data into [0:219] range, and then we use either the CSC_MODE black
screen offset bit, or the CSC post offsets to shift the data to
the correct [16:235] range.
Also have to change the confiuration of all planes so that the
data is sent through the pipe CSC unit. For simplicity send the
plane data through the pipe CSC unit always, and in case full
range output is requested, the pipe CSC unit is set up with an
identity transform to pass the plane data through unchanged.
I've been told by some hardware people that the use of the pipe
CSC unit shouldn't result in any measurable increase in power
consumption numbers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The bit controlling whether PIPE_CONTROL DW/QW write targets
the global GTT or PPGTT moved moved from DW 2 bit 2 to
DW 1 bit 24 on IVB.
I verified on IVB that the fix is in fact effective. Without the fix
none of the scratch writes actually landed in the pipe control page.
With the fix the writes show up correctly.
v2: move PIPE_CONTROL_GLOBAL_GTT_IVB setup to where other flags are set
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similarly to:
commit 6a0d1df3d3a0d2370541164eb0595fe35dcd6de3
Author: Damien Lespiau <damien.lespiau@intel.com>
Date: Tue Dec 11 15:18:28 2012 +0000
drm/i915: Preserve the FDI line reversal override bit on CPT
DDI port support lane reversal to easy the PCB layouting work. Let's
preserve the bit configured by the BIOS (until we find how to correctly
retrieve the information from the VBT, but this does sound more fragile
then just relying on the BIOS that has, hopefully, been validated
already.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The FDI link has supported link reversal to make the PCB layout
engineer's life easier for quite a while and we have always presered
this bit as we programmed FDI_RX_CTL with a read/modify/write sequence.
We're trying to take a bit more control over what the BIOS leaves in
various register and with the introduction of DDI, started to program
FDI_RX_CTL fully.
There's a fused bit to indicate DMI link reversal and FDI defaults to
mirroring that configuration. We have a bit to override that behaviour
that we need to preserve from the BIOS.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some early bios versions seem to ship with the wrong tuning values for
the MCH, possible resulting in pipe underruns under load. Especially
on DP outputs this can lead to black screen, since DP really doesn't
like an occasional whack from an underrun.
Unfortunately the registers seem to be locked after boot, so the only
thing we can do is politely point out issues and suggest a BIOS
upgrade.
Arthur Runyan pointed us at this issue while discussion DP bugs - thus
far no confirmation from a bug report yet that it helps. But at least
some of my machines here have wrong values, so this might be useful in
understanding bug reports.
v2: After a bit more discussion with Art and Ben we've decided to only
the check the watermark values, since the OREF ones could be be a
notch more aggressive on certain machines.
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Runyan, Arthur J <arthur.j.runyan@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
They're physically the same pins and also the same bits, duplicating
only confuses the reader. This also makes it a bit obvious that we
have quite some code duplication going on here. Squashing that is for
a larger rework in our hpd handling though.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The RC6 VIDS has a linear ramp starting at 250mv, which means any values
below 250 are invalid. The old buggy macros tried to adjust for this to
be more flexible, but there is no need. As Dan pointed out the ENCODE
only ever has one value. The only invalid value for decode is an input
of 0 which means something is really wonky, and the cases where DECODE
are used either don't matter (debug values), or would be implicitly
correct (the check for less than 450).
This patch makes simpler, easier to read macros which are actually
correct. Maybe this patch can actually fix some bugs now.
Thanks to Dan for catching this. /me hides
Cc: stable@kernel.org
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This pulls in most of Linus tree up to -rc6, this fixes the worst lockdep
reported issues and re-enables fbcon lockdep.
(not the fbcon maintainer)
* 'fbcon-locking-fixes' of ssh://people.freedesktop.org/~airlied/linux: (529 commits)
Revert "Revert "console: implement lockdep support for console_lock""
fbcon: fix locking harder
fb: Yet another band-aid for fixing lockdep mess
fb: rework locking to fix lock ordering on takeover
The VGACNTRL register has moved around between different platforms.
To handle the differences add i915_vgacntrl_reg() which returns the
correct offset for the VGACNTRL register.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The shift changed, hurray.
Reported-by: Kenneth Graunke <kenneth@whitecape.org>
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Implements WaVSRefCountFullforceMissDisable as documented in the BSpec
3D workarounds chapter.
Cc: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The current code was wrong in many different ways, so this is a full
rewrite. We don't have "different power wells for different parts of
the GPU", we have a single power well, but we have multiple registers
that can be used to request enabling/disabling the power well. So
let's be a good citizen and only use the register we're suppose to
use, except when we're loading the driver, where we clear the request
made by the BIOS.
If any of the registers is requesting the power well to be enabled, it
will be enabled. If none of the registers is requesting the power well
to be enabled, it will be disabled.
For now we're just forcing the power well to be enabled, but in the
next commits we'll change this.
V2:
- Remove debug messages that could be misleading due to possible
race conditions with KVMr, Debug and BIOS.
- Don't wait on disabling: after a conversaion with a hardware
engineer we discovered that the "restriction" on bit 31 is just
for the "enable" case, and we don't even need to wait on the
"disable" case.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
SR01 needs to be touched to disable VGA on non-UMS setups too.
So the sequencer registers need to include the appripriate offset
on VLV.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Dropped the clock gating registers
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of 0x18xxxx use (VLV_DISPLAY_BASE + xxxx).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of 0x18xxxx use (VLV_DISPLAY_BASE + xxxx).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CURSIZE is not present on VLV, so it was left out, as were the IVB
specific cursor B registers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is a required workarounds for all products, especially on gen6+
where it causes the command streamer to fail to parse instructions
following a WAIT_FOR_EVENT. We use WAIT_FOR_EVENT for synchronising
between the GPU and the display engines, and so this bit being unset may
cause hangs.
References: https://bugzilla.kernel.org/show_bug.cgi?id=52311
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The RGB color range select bit on the DP/SDVO/HDMI registers
disappeared when PCH was introduced, and instead a new PIPECONF bit
was added that performs the same function.
Add a new INTEL_MODE_LIMITED_COLOR_RANGE private mode flag, and set
it in the encoder mode_fixup if limited color range is requested.
Set the the PIPECONF bit 13 based on the flag.
Experimentation showed that simply toggling the bit while the pipe is
active doesn't work. We need to restart the pipe, which luckily already
happens.
The DP/SDVO/HDMI bit 8 is marked MBZ in the docs, so avoid setting it,
although it doesn't seem to do any harm in practice.
TODO:
- the PIPECONF bit too seems to have disappeared from HSW. Need a
volunteer to test if it's just a documentation issue or if it's really
gone. If the bit is gone and no easy replacement is found, then I suppose
we may need to use the pipe CSC unit to perform the range compression.
v2: Use mode private_flags instead of intel_encoder virtual functions
v3: Moved the intel_dp color_range handling after bpc check to help
later patches
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=46800
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix up some copypaste errors in the PIPESTAT register for VLV.
SPRITE0_FLIP_DONE_INT_EN_VLV is bit 22, not bit 26.
SPRITE0_FLIPDONE_INT_STATUS_VLV is bit 14, not bit 15.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes:
- seqno wrap fixes and debug infrastructure from Mika Kuoppala and Chris
Wilson
- some leftover kill-agp on gen6+ patches from Ben
- hotplug improvements from Damien
- clear fb when allocated from stolen, avoids dirt on the fbcon (Chris)
- Stolen mem support from Chris Wilson, one of the many steps to get to
real fastboot support.
- Some DDI code cleanups from Paulo.
- Some refactorings around lvds and dp code.
- some random little bits&pieces
* tag 'drm-intel-next-2012-12-21' of git://people.freedesktop.org/~danvet/drm-intel: (93 commits)
drm/i915: Return the real error code from intel_set_mode()
drm/i915: Make GSM void
drm/i915: Move GSM mapping into dev_priv
drm/i915: Move even more gtt code to i915_gem_gtt
drm/i915: Make next_seqno debugs entry to use i915_gem_set_seqno
drm/i915: Introduce i915_gem_set_seqno()
drm/i915: Always clear semaphore mboxes on seqno wrap
drm/i915: Initialize hardware semaphore state on ring init
drm/i915: Introduce ring set_seqno
drm/i915: Missed conversion to gtt_pte_t
drm/i915: Bug on unsupported swizzled platforms
drm/i915: BUG() if fences are used on unsupported platform
drm/i915: fixup overlay stolen memory leak
drm/i915: clean up PIPECONF bpc #defines
drm/i915: add intel_dp_set_signal_levels
drm/i915: remove leftover display.update_wm assignment
drm/i915: check for the PCH when setting pch_transcoder
drm/i915: Clear the stolen fb before enabling
drm/i915: Access to snooped system memory through the GTT is incoherent
drm/i915: Remove stale comment about intel_dp_detect()
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
These are useful for investigating hangs involving WAIT_FOR_EVENT.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Apply a droplet of Future-Proof in the if-ladder.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I'm not really sure, since the w/a entry is as thin on details as
ever, and Bspec doesn't say anything about it. But I've figured only
dispatching to rows 0&1 instead of all four should be the right thing
for GT1.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Add the missing snb server GT1 to the check, spotted by Chris
Wilson.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Quoting from Bspec, 3D_CHICKEN1, bit 10
This bit needs to be set always to "1", Project: DevSNB "
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ilk+ somehow used #defines in near the PIPESTAT definitions, which
decently confused me. Earlier platforms called it BPP instead of
BPC. Clean this all up.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Those status bits don't follow the usual pattern: _MASK (those bits are
write 1 to clear, useful to select the value we want to read) and the
values shifted by the same amount.
Cleaned that that up when poking at the register for testing purposes,
might as well upstream that cleanup.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we fail to set the bit when needed we get some nice FDI link
training failures (AKA "black screen on VGA output").
While we don't really know how to properly choose whether we need to
set the bit or not (VBT?), just read the initial value set by the BIOS
and store it for later usage.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need this code to init the PCH SSC refclk and the FDI registers.
The BIOS does this too and that's why VGA worked before this patch,
until you tried to suspend the machine...
This patch implements the "Sequence to enable CLKOUT_DP for FDI usage
and configure PCH FDI/IO" from our documentation.
v2:
- Squash Damien Lespiau's reset spelling fix on top.
- Add a comment that we don't need to bother about the ULT special
case Damien noticed, since ULT won't have VGA.
- Add a comment to rip out the SDV codepaths once haswell ships for
real.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This way we should be able to write mPHY registers using the Sideband
Interface in the next commit. Also fixed some syntax oddities in the
related code.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
TRANS_DP_VIDEO_AUDIO is not used at all.
The other 3 has duplicated #defines.
Signed-off-by: Dexuan Cui <dexuan.cui@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Somehow a chunk of unused register defines ended up in the middle of
the PLL defines. They go back to the original kms merging.
The only used #define is SR01, move it to the register name together
with the other legacy vga stuff.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I actually found this problem on Haswell, but then discovered Ivy
Bridge also has it by reading the spec.
I don't have the hardware to test this.
Cc: stable@vger.kernel.org
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DDI A and E have 4 lanes to share, so if DDI A is using 4 lanes,
there's nothing left for DDI E, which means there's no CRT port on the
machine.
The bit we're checking here is programmed at system boot and it cannot
be changed afterwards, so we cannot change the amount of lanes
reserved for each DDI port.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to enable a special bit, otherwise none of the DP functions
requiring the PCH will work.
Version 2: store the PCH ID inside dev_priv, as suggested by Daniel
Vetter.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's pretty much all consolidated now that we've killed AGP. We can move
the one outlier, and defines too.
(Kill some unused defines in the process)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows us to map the PTEs WC. I've not done thorough testing or
performance measurements with this patch, but it should be decent.
This is based on a patch from Jesse with the original commit message
> I've only lightly tested this so far, but the corruption seems to be
> gone if I write the GFX_FLSH_CNTL reg after binding an object. This
> register should control the TLB for the system agent, which is what CPU
> mapped objects will go through.
It has been updated for the new AGP-less code by me, and included with
it is feedback from the original patch.
v2: Updated to reflect paranoia on pte updates/register posting reads.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by [v1]: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This bug existed in the old code, but was easier to fix here in the
rework. Unfortunately gen7 doesn't have a nice way to figure out the
size and we must use a lookup table.
As Jesse pointed out, there is some confusion in the docs about these
definitions. We're picking the one which seems more accurate, but we
really aren't certain.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As a quick hack we make the old intel_gtt structure mutable so we can
fool a bunch of the existing code which depends on elements in that data
structure. We can/should try to remove this in a subsequent patch.
This should preserve the old gtt init behavior which upon writing these
patches seems incorrect. The next patch will fix these things.
The one exception is VLV which doesn't have the preserved flush control
write behavior. Since we want to do that for all GEN6+ stuff, we'll
handle that in a later patch. Mainstream VLV support doesn't actually
exist yet anyway.
v2: Update the comment to remove the "voodoo"
Check that the last pte written matches what we readback
v3: actually kill cache_level_to_agp_type since most of the flags will
disappear in an upcoming patch
v4: v3 was actually not what we wanted (Daniel)
Make the ggtt bind assertions better and stricter (Chris)
Fix some uncaught errors at gtt init (Chris)
Some other random stuff that Chris wanted
v5: check for i==0 in gen6_ggtt_bind_object to shut up gcc (Ben)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by [v4]: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Make the cache_level -> agp_flags conversion for pre-gen6 a
tad more robust by mapping everything != CACHE_NONE to the cached agp
flag - we have a 1:1 uncached mapping, but different modes of
cacheable (at least on later generations). Suggested by Chris Wilson.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So store into the scratch space of the HWS to make sure the invalidate
occurs.
v2: use GTT address space for store, clean up #defines (Chris)
v3: use correct #define in blt ring flush (Chris)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Antti Koskipää <antti.koskipaa@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
References: https://bugs.launchpad.net/ubuntu/+source/xserver-xorg-video-intel/+bug/1063252
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Workaround for dual port PS dispatch on GT1.
v2: pull in register definition & offset handling
v3: use IVB GT1 macro to get the right regs (Ben)
v4: add for VLV too (Ben)
v5: don't read the reg, it's masked so we'll only enable the one extra bit (Chris)
v6: use a _GT2 suffix for the second reg (Chris)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Antti Koskipää <antti.koskipaa@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky