The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/pinctrl/zte/pinctrl-zx.c:415:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 407, but without a corresponding object release within this function.
./drivers/pinctrl/zte/pinctrl-zx.c:422:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 407, but without a corresponding object release within this function.
./drivers/pinctrl/zte/pinctrl-zx.c:436:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 407, but without a corresponding object release within this function.
./drivers/pinctrl/zte/pinctrl-zx.c:444:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 407, but without a corresponding object release within this function.
./drivers/pinctrl/zte/pinctrl-zx.c:448:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 407, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Jun Nie <jun.nie@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The call to of_get_child_by_name returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/pinctrl/pinctrl-pistachio.c:1422:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1360, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
H6 SoC has a "pio group withstand voltage mode" register (datasheet
description), that needs to be used to select either 1.8V or 3.3V I/O mode,
based on what voltage is powering the respective pin banks and is thus used
for I/O signals.
Add support for configuring this register according to the voltage of the
pin bank regulator (if enabled).
This is similar to the support for I/O bias voltage setting patch for A80
and the same concerns apply. See:
commit 402bfb3c13 ("Support I/O bias voltage setting on A80")
Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
H6 has a different I/O voltage bias setting method than A80. Prepare
existing code for using alternative bias voltage setting methods.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The call to of_get_child_by_name returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/pinctrl/pinctrl-st.c:1188:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1175, but without a corresponding object release within this function.
./drivers/pinctrl/pinctrl-st.c:1188:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1175, but without a corresponding object release within this function.
./drivers/pinctrl/pinctrl-st.c:1199:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1175, but without a corresponding object release within this function.
./drivers/pinctrl/pinctrl-st.c:1199:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1175, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org (open list)
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The call to of_find_compatible_node returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/pinctrl/samsung/pinctrl-exynos-arm.c:76:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 66, but without a corresponding object release within this function.
./drivers/pinctrl/samsung/pinctrl-exynos-arm.c:82:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 66, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Align pins names with names provided in official stm32mp157 datasheet
available on st.com.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A same SoC can be available in several packages. Differences between
packages are only the numbers of available balls. In order not to write
a driver for each new package, same driver (ex: pinctrl-stm32mp157.c) will
be used. This patch introduces the "package" property for each pin. So on a
same driver, it will be possible to indicate on which package the pin is
available. The package information will be got from the device tree.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To support pinctl hog restore after LPSR resume back,
add the generic suspend/resume in pinctrl-imx along with the
generic pm ops to be used by platform specific drivers. Then
make use of the newly added ops in i.MX8MQ platform specific
driver.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pincontrol callbacks used to be symmetric:
enable/disable.
However for a while we only have one function that
set the muxing, no disabling.
Drop the unused disable function, and rename the
*enable() function to *set().
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Cc: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some of the AMD reference boards used single GPIO line for
multiple devices. So added IRQF_SHARED flag in amd pinctrl driver.
Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the iMX7d datasheet, the PAD_CTL_DSE_X* values are different from
the documentation.
Changes since v2:
* Changed patch title to 'dt-bindings: pinctrl: imx7d:'
Signed-off-by: Christina Quast <cquast@hanoverdisplays.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper devm_platform_ioremap_resource() which wraps the
platform_get_resource() and devm_ioremap_resource() together, to
simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The address of "ipctl->pin_regs[pin_id]" can't be NULL. It's the offset
into an array in the middle of a struct. This patch removes the check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch provides the advanced drive for I2C used pins on MT8183.
The detail strength specification description of the I2C pin:
When E1=0/E0=0, the strength is 0.125mA.
When E1=0/E0=1, the strength is 0.25mA.
When E1=1/E0=0, the strength is 0.5mA.
When E1=1/E0=1, the strength is 1mA.
For I2C pins, there are existing generic driving setup and the above
specific driving setup. I2C pins can only support 2/4/6/8/10/12/14/16mA
driving adjustment in generic driving setup. But in specific driving
setup, they can support 0.125/0.25/0.5/1mA adjustment.
If we enable specific driving setup for I2C pins,
the existing generic driving setup will be disabled.
For some special features, we need the I2C pins specific driving setup.
The specific driving setup is controlled by E1E0EN.
So we need add extra vendor driving preperty instead of the generic
driving property. We can add "mediatek,drive-strength-adv = <XXX>;"
to describe the specific driving setup property.
"XXX" means the value of E1E0EN. So the valid arguments of
"mediatek,drive-strength-adv" are from 0 to 7.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The commit adds mt8183 compatible node in binding document.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
axp20x_build_funcs_groups allocates groups via devm_kcalloc and tries to
dereference without checking for NULL. This patch avoids such a
scenario.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
EXPORT_SYMBOL_GPL() needs a semicolon at the end, also
explicitly include <linux/export.h> as well.
Fixes: 64ebde5b0f ("gpiolib: export devprop_gpiochip_set_names()")
Acked-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix sparse warnings:
drivers/pinctrl/pinctrl-artpec6.c:691:5: warning:
symbol 'artpec6_pmx_enable' was not declared. Should it be static?
drivers/pinctrl/pinctrl-artpec6.c:705:6: warning:
symbol 'artpec6_pmx_disable' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add HSCIF (serial) pin groups on R-Car H1,
- Add I2C[035] pin groups on R-Car M3-N,
- Add CANFD pin groups on RZ/G2M and RZ/G2E,
- Retain SDHI/MMC clock return path delay configuration across
suspend/resume on R-Car Gen3,
- More validation of pinmux tables at build and runtime, including
compile-test coverage of all drivers,
- Small fixes, improvements, and cleanups.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXKXovAAKCRCKwlD9ZEnx
cFeBAQCiXbVnEVAD4eIuPal5ZnEAp5M8/eBBE9un3je69kCd0AD/V1doqUtXcNk1
stfcNWtBxeRzOJAMsPyPDuTQRC5jWQo=
=ZrZI
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v5.2-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v5.2
- Add HSCIF (serial) pin groups on R-Car H1,
- Add I2C[035] pin groups on R-Car M3-N,
- Add CANFD pin groups on RZ/G2M and RZ/G2E,
- Retain SDHI/MMC clock return path delay configuration across
suspend/resume on R-Car Gen3,
- More validation of pinmux tables at build and runtime, including
compile-test coverage of all drivers,
- Small fixes, improvements, and cleanups.
This patch adds I2C{0,3,5} pins, groups and functions to the R8A7796 SoC.
These pins are physically muxed with other pins. Therefore, setup of
MOD_SEL is needed for exclusive control with other pins.
[takeshi.kihara.df: add blank lines after function declarations]
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[uli: use standard macros PINMUX_IPSR_PHYS and PINMUX_IPSR_PHYS_MSEL]
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Pin data for I2C controllers 0, 3 and 5 is properly defined already.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fix sparse warning:
drivers/pinctrl/freescale/pinctrl-scu.c:38:19: warning:
symbol 'pinctrl_ipc_handle' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Lochnagar is an evaluation and development board for Cirrus
Logic Smart CODEC and Amp devices. It allows the connection of
most Cirrus Logic devices on mini-cards, as well as allowing
connection of various application processor systems to provide a
full evaluation platform. This driver supports the board
controller chip on the Lochnagar board.
Lochnagar provides many pins which can generally be used for an
audio function such as an AIF or a PDM interface, but also as
GPIOs.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Lochnagar is an evaluation and development board for Cirrus
Logic Smart CODEC and Amp devices. It allows the connection of
most Cirrus Logic devices on mini-cards, as well as allowing
connection of various application processor systems to provide a
full evaluation platform. This driver supports the board
controller chip on the Lochnagar board.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Our pinctrl drivers are consisting of some common code, and big pin tables
that are SoC-specific. This is fine in most cases, but when you want to
reduce the size of the particular kernel image, those big tables are, well,
quite big.
We haven't had the option to disable them in the past since they were
hidden Kconfig options based on the SoC support. However, that granularity
isn't great since we don't have one Kconfig option per-SoC, but rather one
by family.
Make those options selectable by the user so that they can disable it if
needed, while keeping the current default to not change the standard case.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Our pin controller can configure the pins no matter how they are muxed, so
it makes sense to allow this for GPIOs as well.
Add the generic set_config function so that we can rely on the existing
pinctrl code we have.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Lines are usually ended with a semi-column in C, yet this was copied from a
structure declaration to the init variant while keeping the comma at the
end. Make sure we have a normal syntax, instead of multiple assignments.
Fixes: d83c82ce7c ("pinctrl: sunxi: support multiple pin controller")
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The sunxi pinctrl only implements the pin_config_group_set callback at the
moment, whereas the gpiochip_generic_config function relies on
pin_config_set. Rework the functions a little to support pin_config_set,
and rely on it for pin_config_group_set.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.50 of Feb
12, 2019, the sel_ndfc MOD_SEL register bit is renamed to sel_ndf.
Update the pin control drivers to reflect this.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Update R-Car E3]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
According to the R-Car Gen3 Hardware Manual Errata for Rev 0.80 of Dec
22, 2017, and the Errata for Rev 1.50 of Dec 25, 2018, MOD_SEL0 register
bits 3, 4, 17, and 18 are renamed from SEL_ADG_{A,B,C} to
SEL_ADG{A,B,C}. Update the pin control drivers to reflect this.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.50 of
Feb 12, 2019, the RTS{0,1,3,4}_#/TANS pin names defined in the GPSR and
IPSR registers are renamed to RTS{0,1,3,4}_#.
This patch updates the pin control drivers to reflect this.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Update R-Car H3 ES1.x, V3M, V3H, and D3]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
Jun 4, 2018, the CC5_OSCOUT pin is removed. Update the pin control
drivers to reflect this.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Update R-Car V3M, V3H]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The HDMI CEC function is not supported by the R-Car Gen3 Hardware Manual
Rev 1.00. Therefore, delete the corresponding pin groups and functions,
and rename the HDMI[01]_CEC definitions to match their GPIO
functionality.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Squashed several commits]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of Aug
24, 2018, there is no need to configure MOD_SEL1 bit30 when the
SSI_SCK2_{A,B} or SSI_WS2_{A,B} pin functions are selected.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Remove now unused definitions, mark MOD_SEL1 bit30 reserved]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
Aug 24, 2018, there is no need to configure MOD_SEL1 bit31 when the
SIM0_D_{A,B} pin function is selected.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Remove now unused definitions, mark MOD_SEL1 bit31 reserved]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of Aug
24, 2018, the MOD_SEL0 bit16 must be set to 0 when the NFALE_A and
NFRB_N_A pin functions are selected.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
- The IPSR field is meant for documentation only,
- The function name refers to the pin function, not to the IPSR
field.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
rza1_get_bit() is just a single register read. Hence there's no need to
synchronize it with other register writes to the same bank.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jacopo Mondi <jacopo@jmondi.org>
Add a run-time check to the PINMUX_CFG_REG_VAR() macro, to ensure the
number of provided enum IDs is correct. This cannot be done at build
time, as the number of values depends on the variable-width fields in
the config register.
This helps catching bugs early.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add build-time checks to the PINMUX_CFG_REG() and PINMUX_DATA_REG()
macros, to ensure the number of provided enum IDs is correct.
This helps catching bugs early.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Currently the PINMUX_DATA_REG() macro must be followed by initialization
data, specifying all enum IDs. Hence the macro itself does not know
anything about the enum IDs, preventing the macro from performing any
validation on it.
Make the macro accept the enum IDs as a parameter, and update all users.
Note that array data enclosed by curly braces cannot be passed to a
macro as a parameter, hence the enum IDs are wrapped using the GROUP()
macro.
No functional changes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Currently the PINMUX_CFG_REG_VAR() macro must be followed by
initialization data, specifying all enum IDs. Hence the macro itself
does not know anything about the enum IDs, preventing the macro from
performing any validation on it.
Make the macro accept the enum IDs as a parameter, and update all users.
Note that array data enclosed by curly braces cannot be passed to a
macro as a parameter, hence both the register field widths and the enum
IDs are wrapped using the GROUP() macro.
No functional changes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Currently the PINMUX_CFG_REG() macro must be followed by initialization
data, specifying all enum IDs. Hence the macro itself does not know
anything about the enum IDs, preventing the macro from performing any
validation on it.
Make the macro accept the enum IDs as a parameter, and update all users.
Note that array data enclosed by curly braces cannot be passed to a
macro as a parameter, hence the enum IDs are wrapped using a new macro
GROUPS().
No functional changes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable compile-testing of all Renesas SuperH and ARM pin control
drivers, in a similar way as was done before for clock and SoC drivers
in commits 371dd373c6 ("clk: renesas: Allow compile-testing of all
(sub)drivers") and 8be381a131 ("soc: renesas: Rework Kconfig and
Makefile logic").
The SuperH pin control drivers need specific include files, hence make
sure they are always found when compile-testing.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
When compile-testing on arm:
arch/sh/include/cpu-sh4/cpu/sh7786.h: In function ‘sh7786_mm_sel’:
arch/sh/include/cpu-sh4/cpu/sh7786.h:135:21: warning: passing argument 1 of ‘__raw_readl’ makes pointer from integer without a cast [-Wint-conversion]
return __raw_readl(0xFC400020) & 0x7;
^~~~~~~~~~
In file included from include/linux/io.h:25:0,
from arch/sh/include/cpu-sh4/cpu/sh7786.h:14,
from drivers/pinctrl/sh-pfc/pfc-sh7786.c:15:
arch/arm/include/asm/io.h:113:21: note: expected ‘const volatile void *’ but argument is of type ‘unsigned int’
#define __raw_readl __raw_readl
^
arch/arm/include/asm/io.h:114:19: note: in expansion of macro ‘__raw_readl’
static inline u32 __raw_readl(const volatile void __iomem *addr)
^~~~~~~~~~~
__raw_readl() on SuperH is a macro that casts the passed I/O address to
the correct type, while the implementations on most other architectures
expect to be passed the correct pointer type.
Add an explicit cast to fix this.
Note that this also gets rid of a sparse warning on SuperH:
arch/sh/include/cpu-sh4/cpu/sh7786.h:135:16: warning: incorrect type in argument 1 (different base types)
arch/sh/include/cpu-sh4/cpu/sh7786.h:135:16: expected void const volatile [noderef] <asn:2>*<noident>
arch/sh/include/cpu-sh4/cpu/sh7786.h:135:16: got unsigned int
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Wen Yang