This patch fixes the errors made in the users of the crypto layer during
the sg_init_table conversion. It also adds a few conversions that were
missing altogether.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most drivers need to set length and offset as well, so may as well fold
those three lines into one.
Add sg_assign_page() for those two locations that only needed to set
the page, where the offset/length is set outside of the function context.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The original serial-number calculations based on WWPN no longer
apply to newer ISPs (ISP24xx and ISP25xx). These newer board's
serial number reside in the VPD.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
For recent ISPs, software during CS_UNDERRUN handling must
determine if the two residuals, firmware-calculated and FCP_RSP,
are different to recognize if a frame has been dropped. Update
the driver to catch this condition, and clear the
SS_RESIDUAL_UNDER and lscsi_status bits. This logic is
consistent with what earlier firmwares did by explicitly
cracking open the FCP_RSP statuses and clearing
SS_RESIDUAL_UNDER.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Recent ISPs need only the single MMIO BAR to manipulate HW
registers. Unfortunately, ISP21xx, ISP22xx, ISP23xx, and ISP63xx
type cards still require the I/O mapped region to manipulate the
FLASH via the two HW flash-registers (flash_address and
flash_data).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original implementation would not use the burst-write mechanisms
for requests equal to OPTROM_BURST_DWORDS transfer dwords.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Since both NVRAM and VPD regions of the flash reside on unaligned
sector boundaries, during update, the driver must perform a
read-modify-write operation to the composite NVRAM/VPD region.
This affects ISP25xx type boards only.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
As the intermixing may cause issues where HCCR bits could be
cleared inappropriately during MSI/MSI-X interrupt handling.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This function just printed a message to the user; move the print to its
only caller, and turn it into an starget_printk.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This structure is accessed by the device; the fewer Linux things in it,
the better. Using the pci_dev pointer from the hostdata requires a lot
of changes:
- Pass Scsi_Host to a lot of routines which currently take a sym_hcb.
- Set the Scsi_Host as the pci drvdata (instead of the sym_hcb)
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make sym_interrupt return an irqreturn_t instead of void, and take a
Scsi_Host instead of a sym_hcb. Pass the Scsi_Host to the interrupt
handler instead of the sym_hcb. Rename the host_data to sym_data.
Keep a pci_dev pointer in the sym_data. Rename the Scsi_Host from
instance to shost.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
These macros aren't needed any more. They used to be used for SPARC.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If we have a scsi_cmnd, it gives the user more information than the
sym_name, and maybe the target.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
By introducing the use_dac(), set_dac() and DMA_DAC_MASK macros, we can
eliminate a lot of ifdefs from the code. We now rely on the compiler to
optimise away a few things that we'd formerly relied on the preprocessor
to do. This makes sym_setup_bus_dma_mask() small enough to inline into
its only caller.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
With sysfs making these options tunable at runtime, there's no
justification for keeping this horrendously complex specification
string around.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
These struct elements record info that is never needed
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Following the same path as ->revision_id, remove ->device_id
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Auke missed the sym2 driver in his initial sweep.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds the PCI error recovery callbacks to the Symbios SCSI device
driver. It includes support for First Failure Data Capture.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Assorted changes to initial patches, including returning IRQ_NONE from the
interrupt handler if the device is offline and re-using the eh_done completion
in the scsi error handler.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Instead of telling the reset routine that the command completed from
sym_eh_done, do it from sym_xpt_done. The 'to_do' element of the ucmd
is redundant -- it serves only to tell whether eh_done is valid or not,
and we can tell this by checking to see if it's NULL.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Interrupts can't be re-entered, so it's sufficient to call spin_lock, not
spin_lock_irqsave().
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The midlayer won't scan the host ID, so we don't need to check.
This is the only caller of sym_xpt_done2, so remove that too.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Before all commands used sg, data_mapping and data_mapped were used to
distinguish whether the command had used map_single or map_sg. Now all
commands are sg, so we can delete data_mapping, data_mapped and the
wrapper functions __unmap_scsi_data, __map_scsi_sg_data, unmap_scsi_data
and map_scsi_sg_data.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Don't cache a private copy of the interrupt number
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Prevent DMA transfers from crossing the 16MB limit for early 53c896 chips.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
i think there is wasted space in allocated pages for request and
response rings. The allocations are made with REQUEST_ENTRY_CNT + 1
and RESPONSE_ENTRY_CNT + 1, but they are set with 256 and 16.
So we got more pages, which we dont use very much so eliminate them.
Signed-off-by: Johannes Dickgreber <tanzy@gmx.de>
Acked-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix fallout from 18dabf473e15850c0dbc8ff13ac1e2806d542c15:
In file included from include/linux/dma-mapping.h:52,
from drivers/base/dma-mapping.c:10:
include/asm/dma-mapping.h: In function 'dma_map_sg':
include/asm/dma-mapping.h:288: error: 'struct scatterlist' has no member named 'page'
include/asm/dma-mapping.h:288: error: 'struct scatterlist' has no member named 'page'
include/asm/dma-mapping.h:288: error: 'struct scatterlist' has no member named 'page'
include/asm/dma-mapping.h:289: error: 'struct scatterlist' has no member named 'page'
include/asm/dma-mapping.h:290: error: 'struct scatterlist' has no member named 'page'
include/asm/dma-mapping.h: In function 'dma_sync_sg_for_cpu':
include/asm/dma-mapping.h:331: error: 'struct scatterlist' has no member named 'page'
drivers/scsi/ps3rom.c: In function 'fetch_to_dev_buffer':
drivers/scsi/ps3rom.c:150: error: 'struct scatterlist' has no member named 'page'
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
If a prefix is selected for flex, we should be using it everywhere.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The aic7xxx driver already contains fragments for suspend/resume
support. So we only need to update them to the current interface
and have full PCI suspend/resume.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Tested-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A failure here wouldn't currently free the irq; go to the irq free
path instead.
Signed-off-by: Johannes Dickgreber <tanzy@gmx.de>
Acked-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* Convert files to UTF-8.
* Also correct some people's names
(one example is Eißfeldt, which was found in a source file.
Given that the author used an ß at all in a source file
indicates that the real name has in fact a 'ß' and not an 'ss',
which is commonly used as a substitute for 'ß' when limited to
7bit.)
* Correct town names (Goettingen -> Göttingen)
* Update Eberhard Mönkeberg's address (http://lkml.org/lkml/2007/1/8/313)
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Prior to use struct marker in the linux kernel markers, we need to clean
two drivers which use this structure name.
Change bonding driver types :
- struct marker to struct bond_marker.
- marker_t to bond_marker_t.
- marker_header to bond_marker_header.
- marker_header_t to bond_marker_header_t.
Change qla4xxx struct marker_entry usage :
- Change struct marker_entry for struct qla4_marker_entry.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Chad Tindel <ctindel@users.sourceforge.net>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: David Somayajulu <david.somayajulu@qlogic.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Cc: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The task_struct->pid member is going to be deprecated, so start
using the helpers (task_pid_nr/task_pid_vnr/task_pid_nr_ns) in
the kernel.
The first thing to start with is the pid, printed to dmesg - in
this case we may safely use task_pid_nr(). Besides, printks produce
more (much more) than a half of all the explicit pid usage.
[akpm@linux-foundation.org: git-drm went and changed lots of stuff]
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
FlashPoint, use BIT instead of BITW
BITW was an ushort variant of BIT, use BIT instead
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
define global BIT macro
move all local BIT defines to the new globally define macro.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
remove asm/bitops.h includes
including asm/bitops directly may cause compile errors. don't include it
and include linux/bitops instead. next patch will deny including asm header
directly.
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] kill ata_sg_is_last()
Update libata driver for bf548 atapi controller against the 2.6.24 tree.
libata-sff: Correct use of check_status()
drivers/ata: add support to Freescale 3.0Gbps SATA Controller
pata_acpi: fix build breakage if !CONFIG_PM
Found these while looking at printk uses.
Add missing newlines to dev_<level> uses
Add missing KERN_<level> prefixes to multiline dev_<level>s
Fixed a wierd->weird spelling typo
Added a newline to a printk
Signed-off-by: Joe Perches <joe@perches.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Smart <James.Smart@Emulex.Com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Short term, this works around a bug introduced by early sg-chaining
work.
Long term, removing this function eliminates a branch from a hot
path loop in each scatter/gather table build. Also, as this code
demonstrates, we don't need to _track_ the end of the s/g list, as
long as we mark it in some way. And doing so programatically is nice.
So its a useful cleanup, regardless of its short term effects.
Based conceptually on a quick patch by Jens Axboe.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch fixes the following build warnings:
WARNING: vmlinux.o(.text+0xbcffdb): Section mismatch: reference to .init.text.20:gdth_search_drives (between 'gdth_pci_probe_one' and 'gdth_start_timeout')
WARNING: vmlinux.o(.text+0xbd0102): Section mismatch: reference to .init.text.20:gdth_enable_int (between 'gdth_pci_probe_one' and 'gdth_start_timeout')
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Commit bbfbbbc118 accidentally reversed
the logic of this NULL check.
Spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
drivers/scsi/qla2xxx/qla_sup.c: In function 'qla24xx_write_flash_data':
drivers/scsi/qla2xxx/qla_sup.c:655: warning: format '%llx' expects type 'long long unsigned int', but argument 6 has type 'dma_addr_t'
drivers/scsi/qla2xxx/qla_sup.c: In function 'qla25xx_read_optrom_data':
drivers/scsi/qla2xxx/qla_sup.c:1853: warning: format '%llx' expects type 'long long unsigned int', but argument 6 has type 'dma_addr_t'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch fixes a typo introduced by
commit bbfbbbc118.
It wasn't a compile error since CONFIG_LPFC_DEBUG_FS is not (yet?)
available as an option.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix IRQ reporting - just assign the ->pci_dev pointer earlier and use the
pci_dev irq field rather than keeping a private one
Init the spinlock as it works better on SMP that way
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The newer firmware may return more than 96 bytes of sense data when it
does autosense. Truncate this to the size of the SCSI layer sense
buffer to avoid an overrun.
Signed-off-by: HighPoint Linux Team <linux@highpoint-tech.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
if shost->supported mode is zero (i.e. MODE_UNKNOWN) show it as
initiator (it's obviously an unconverted driver that won't do target).
Acked-by: FUJITA Tomonori <tomof@acm.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Spotted by Paul Jackson <pj@sgi.com>
The error handler rework moved the scatterlist into a globally exposed
structure in scsi_eh.h; unfortunately, the scatterlist include needs
to move from scsi_error.c to scsi_eh.h to allow this to compile
universally.
Acked-by: Paul Jackson <pj@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This code has been slowly rotting for about eight years. It's currently
impeding a few SCSI cleanups, and nobody seems to have hardware to test
it any more. I talked to Dave Miller about it, and he agrees we can
delete it. If anyone wants a software FC stack in future, they can
retrieve this driver from git.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A bit too eager - we definitely need to clear the sg table
initially, so that we don't accidentally have ->page & 0x01
true and think that is a chain pointer.
This reverts commit f5c0dde4c6.
We want to remove sg_last(), it's a very expensive interface. So
keep track of number of sg entries in the sg list, instead of comparing
with the last entry.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
- Previese patch to NCR5380 broke scsi_mac because
AUTOSENSE was defined after the inclusion of
NCR5380.h. Fix it
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts sg segment size ifdefs that the current code has in order
to provide a way to reduce sgpool memory consumption.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This option is true if a low-level driver can support sg
chaining. This will be removed eventually when all the drivers are
converted to support sg chaining. q->max_phys_segments is set to
SCSI_MAX_SG_SEGMENTS if false.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
ips properly uses scsi_for_each_sg for the normal I/O path, however,
the breakup path doesn't.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This is what enables large commands. If we need to allocate an
sgtable that doesn't fit in a single page, allocate several
SCSI_MAX_SG_SEGMENTS sized tables and chain them together.
SCSI defaults to large chained sg tables, if the arch supports it.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Just pass in the command, no point in passing in the scatterlist
and scatterlist pool index seperately.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This converts the SCSI mid layer to using the sg helpers for looking up
sg elements, instead of doing it manually.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
If the gdth module is loaded (or compiled in), the gdth_timeout function
gets started even if no actual gdth controllers are found b the probing.
That ends up not only being unnecessary, but also causes a crash due to
the function blindly just trying to pick the first entry off the
"gdth_instances" list, and accessing it - which obviously doesn't work
if the list is empty!
Noticed by Ingo Molnar.
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (119 commits)
[libata] struct pci_dev related cleanups
libata: use ata_exec_internal() for PMP register access
libata: implement ATA_PFLAG_RESETTING
libata: add @timeout to ata_exec_internal[_sg]()
ahci: fix notification handling
ahci: clean up PORT_IRQ_BAD_PMP enabling
ahci: kill leftover from enabling NCQ over PMP
libata: wrap schedule_timeout_uninterruptible() in loop
libata: skip suppress reporting if ATA_EHI_QUIET
libata: clear ehi description after initial host report
pata_jmicron: match vendor and class code only
libata: add ST9160821AS / 3.ALD to NCQ blacklist
pata_acpi: ACPI driver support
libata-core: Expose gtm methods for driver use
libata: add HDT722516DLA380 to NCQ blacklist
libata: blacklist NCQ on Seagate Barracuda ST380817AS
[libata] Turn on ACPI by default
libata_scsi: Fix ATAPI transfer lengths
libata: correct handling of SRST reset sequences
libata: Integrate ACPI-based PATA/SATA hotplug - version 5
...
This changes the uevent buffer functions to use a struct instead of a
long list of parameters. It does no longer require the caller to do the
proper buffer termination and size accounting, which is currently wrong
in some places. It fixes a known bug where parts of the uevent
environment are overwritten because of wrong index calculations.
Many thanks to Mathieu Desnoyers for finding bugs and improving the
error handling.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/scsi/gdth.c: In function ‘gdth_search_dev’:
drivers/scsi/gdth.c:646: warning: ‘pci_find_device’ is deprecated
(declared at include/linux/pci.h:482)
drivers/scsi/gdth.c: In function ‘gdth_init_isa’:
drivers/scsi/gdth.c:857: error: ‘gdth_irq_tab’ undeclared (first use in
this function)
drivers/scsi/gdth.c:857: error: (Each undeclared identifier is reported
only once
drivers/scsi/gdth.c:857: error: for each function it appears in.)
drivers/scsi/gdth.c: In function ‘gdth_copy_internal_data’:
drivers/scsi/gdth.c:2362: warning: unused variable ‘sg’
Looking into the code I notice that gdth_irq_tab is not declared with
CONFIG_ISA=y and !CONFIG_EISA.
The values seem to be same in 2.6.23 (I am not sure why it has been put
with #ifdefs in -mm) so I have just modified the #ifdef to take care of
CONFIG_ISA as well.
Signed-off-by: Dhaval Giani <dhaval@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Since scsi_esp_{,un}register() are EXPORT_SYMBOL'ed, these functions
(and the functions they use) can't be __dev{init,exit}.
Based on a bug report by Rob Landley.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
gdth_execute() will issue an internal, none scsi-standard commands
onto __gdth_queuecommand(). Since it is not recommended to set
struct scsi_cmnd IO members in llds, gdth now uses internal IO
members for IO. In the case of gdth_execute() these members will be
set properly. In case the command was issued from scsi-ml
(by gdth_queuecommand) they will be set from scsi IO accessors.
* define gdth IO accessors and use them throughout the driver.
* use an sg-of-one in gdth_execute() and fix gdth_special_cmd()
accordingly.
* Clean the not use_sg code path and company
Signed-off-by Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Cleanup the rest of the scsi_cmnd->SCp members and move them
to gdth_cmndinfo:
SCp.this_residual => priority
SCp.buffers_residual => timeout
SCp.Status => status and dma_dir
SCp.Message => info
SCp.have_data_in => volatile wait_for_completion
SCp.sent_command => OpCode
SCp.phase => phase
- Two more members will be naturally removed in the !use_sg cleanup
TODO: What is the meaning of gdth_cmndinfo.phase? (rhetorically)
Signed-off-by Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- scsi_cmnd and specifically ->SCp of, where heavily abused
with internal meaning members and flags. So introduce a new
struct gdth_cmndinfo, put it on ->host_scribble and define a
gdth_cmnd_priv() accessor to retrieve it from a scsi_cmnd.
- The structure now holds two members:
internal_command - replaces the IS_GDTH_INTERNAL_CMD() croft.
sense_paddr - which was a 64-bit spanning on 2 32-bit members of SCp.
More overloaded members from SCp and scsi_cmnd will be moved in a later
patch (For easy review).
- Split up gdth_queuecommand to an additional internal_function. The later
is the one called by gdth_execute(). This will be more evident later in
the scsi accessors patch, but it also facilitates in the differentiation
between internal_command and external. And the setup of gdth_cmndinfo of
each command.
Signed-off-by Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Places like Initialization and Reset that Just loop on all devices can
use the link list with the list_for_each_entry macro.
But the io_ctrl from user mode now suffers performance-wise because
code has to do a sequential search for the requested host number.
I have isolated this search in a gdth_find_ha(int hanum) member
for future enhancement if needed.
Signed-off-by Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Use scsi_add_host and friends and track instances ourselves. And
generally modernize the driver's structure.
- TODO: Next we can remove the controller table
- TODO: Fix use of deprecated pci_find_device()
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- gdth_get_status() returns a single device interrupt IStatus
- gdth_interrupt split to __gdth_interrupt() that receives
flags if is called from gdth_wait().
- Use dev_id passed from kernel and do not loop on all
controllers.
- gdth_wait(), get read of all global variables and call the new
__gdth_interrupt with these variables on the stack
Signed-off-by Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Based on same patch from Christoph Hellwig <hch@lst.de>
- Get rid of all the indirection in the Scsi_Host private data and always
put the gdth_ha_str directly into it.
- Change all internal functions prototype to recieve an "gdth_ha_str *ha"
pointer directlly and kill all that redundent access to the "gdth_ctr_tab[]"
controller-table.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The virt_ctr option allows to register a new scsi_host for each bus
on the raid controller. This non-default option makes no sense with
the current scsi code and prevents cleaning up the host registration,
so remove it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
shuffle scsi_host_template members such that they appear in the
order in which they are defined in the header. this makes is easier
to verify when initializers are missing members.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It was always set to ata_port_disable(). Removed the hook, and replaced
the very few ap->ops->port_disable() callsites with direct calls to
ata_port_disable().
Signed-off-by: Jeff Garzik <jeff@garzik.org>
They are direct equivalents to {read,write}[bwl].
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make reset methods and related functions deal with ata_link instead of
ata_port.
* ata_do_reset()
* ata_eh_reset()
* all prereset/reset/postreset methods and related functions
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Introduce ata_link. It abstracts PHY and sits between ata_port and
ata_device. This new level of abstraction is necessary to support
SATA Port Multiplier, which basically adds a bunch of links (PHYs) to
a ATA host port. Fields related to command execution, spd_limit and
EH are per-link and thus moved to ata_link.
This patch only defines the host link. Multiple link handling will be
added later. Also, a lot of ap->link derefences are added but many of
them will be removed as each part is converted to deal directly with
ata_link instead of ata_port.
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Herbert Xu