There is a missing unlock when we hit the "No beacon slot available"
error condition.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use function pci_pcie_cap() instead of accessing struct member directly.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use function pci_is_pcie() instead of accessing struct member directly.
CC: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use function pci_is_pcie() instead of accessing struct member directly.
CC: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use function pci_is_pcie() instead of accessing struct member directly.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No function declared in gpio.h is used here.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No function declared in gpio.h is used here.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k supports its own set of virtual wiphys, and it uses
the mac80211 idle notifications to know when a device needs
to be idle or not. We recently changed ath9k to force idle
on driver stop() and on resume but forgot to take into account
ath9k's own virtual wiphy idle states. These are used internally
by ath9k to check if the device's radio should be powered down
on each idle call. Without this change its possible that the
device could have been forced off but the virtual wiphy idle
was left on.
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k_hw: warn if we cannot change the power to the chip"
introduced a new warning to indicate chip powerup failures, but this
is not required for devices that have been removed. Handle USB device
removal properly by checking for unplugged status.
For PCI devices, this warning will still be seen when the card is pulled
out, not sure how to check for card removal.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These drivers share one header file, but nothing else. Worse, both
drivers use the rtl8225 part with different register settings. The
results has been some ugly naming -- let's simplify that.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
create_workqueue is deprecated. The workqueue usage does not seem to
demand any special treatment, so do not set any flags either.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Tejun Heo <tj@kernel.org>
Restricting the chainmask to 1 for legacy mode disables useful features
such as MRC, and it reduces the available transmit power.
I can't think of a good reason to do this in legacy mode, so let's just
get rid of that code.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit 'ath9k_hw: Disable PAPRD for rates with low Tx power' changed
the code that sets the PAPRD rate masks to use only either the HT20 mask
or the HT40 mask. This is wrong, as the hardware can still use HT20 rates
even when configured for HT40, and the operating channel mode does not
affect PAPRD operation.
The register for the HT40 rate mask is applied as a mask on top of the
other registers to selectively disable PAPRD for specific rates on HT40
packets only.
This patch changes the code back to the old behavior which matches the
intended use of these registers. While with current cards this should not
make any practical difference (according to Atheros, the HT20 and HT40
mask should always be equal), it is more correct that way, and maybe
the HT40 mask will be used for some rare corner cases in the future.
Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl12xx_get_platform_data() returns an ERR_PTR on failure and it never
returns a NULL.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A previous conversion from semaphoreto mutexes missed the fact that one
of the semaphores was used in interrupt code. Fixed by changing to
a spinlock.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k channel table for 2Ghz does not seems to initialize the 'band'
parameter.Though it does not seems to cause any visible issue it looks
odd when we initialize the 'band' parameter for 5Ghz channel table while
not so for 2Ghz.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When rfkill is enabled, ath9k_hw unnecessarily configured the baseband to
turn off based on GPIO input, however that code was hardcoded to GPIO 0
instead of ah->rfkill_gpio.
Since ath9k uses software rfkill anyway, this code is completely unnecessary
and should be removed in case anything else ever uses GPIO 0.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To improve aggregation length, there should not be more than two fully formed
A-MPDU frames in the hardware queue. To ensure this, the code checks the tx
queue length before forming new A-MPDUs. This can reduce the throughput (or
maybe even starve out A-MPDU traffic) when too many non-aggregated frames are
in the queue.
Fix this by keeping track of pending A-MPDU frames (even when they're sent out
as single frames), but exclude rate control probing frames to improve
performance.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old survey implementation was broken and returned nonsense data.
Clear cycle counters and survey data on reset. Since the cycle counters easily
overflow it's better to keep a local version of collected survey data (in ms
resolution, instead of clockrate) and update this every time survey is
retrieved. If survey is retrieved often enough to avoid cycle counter overflows
this works fine, otherwise we could update survey more often, like ath9k does.
Still only the survey for the current channel is kept.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After merge of the rtl8192ce driver, a powerpc build fails with:
drivers/net/wireless/rtlwifi/rtl8192ce/rtl8192c-sw.c: In function 'rtl92c_init_sw_vars':
drivers/net/wireless/rtlwifi/rtl8192ce/rtl8192c-sw.c:76: error: implicit declaration of function 'vmalloc'
drivers/net/wireless/rtlwifi/rtl8192ce/rtl8192c-sw.c:76: warning: cast to pointer from integer of different size
drivers/net/wireless/rtlwifi/rtl8192ce/rtl8192c-sw.c: In function 'rtl92c_deinit_sw_vars':
drivers/net/wireless/rtlwifi/rtl8192ce/rtl8192c-sw.c:91: error: implicit declaration of function 'vfree'
The problem is fixed by explicitly including the appropriate header.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Target Tx power available in eeprom is for PAPRD. If PAPRD
fails, paprd scale factor needs to be detected from this
target tx power.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the drop in Tx power for a particular mcs rate exceeds
the paprd scale factor, paprd may not work properly. Disable
paprd for any such rates.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add multiple Tx IQ cal support to improve EVM accross
different power levels.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This helper can be used in multiple places. Also make
it inline returning u8.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While compiling linux-next (next-20101216) I fell over this breakage:
...
drivers/net/wireless/iwlwifi/iwl-agn-rs.c: In function ‘iwl_rs_rate_init’:
drivers/net/wireless/iwlwifi/iwl-agn-rs.c:2876:8: error: ‘struct iwl_lq_sta’ has no member named ‘dbg_fixed_rate’
dbg_fixed_rate is only used when CONFIG_MAC80211_DEBUGFS is set:
[ drivers/net/wireless/iwlwifi/iwl-agn-rs.h ]
...
#ifdef CONFIG_MAC80211_DEBUGFS
struct dentry *rs_sta_dbgfs_scale_table_file;
struct dentry *rs_sta_dbgfs_stats_table_file;
struct dentry *rs_sta_dbgfs_rate_scale_data_file;
struct dentry *rs_sta_dbgfs_tx_agg_tid_en_file;
u32 dbg_fixed_rate;
#endif
The issue was introduced by commit a1da077bc36368eb7d6312e7e49260f0a3d92c77:
"iwlwifi: clear dbg_fixed_rate during init"
Signed-off-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PM-QOS value can be user specified via module parameter.
This patch adds few comments regarding this in the driver
code.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not required for USB devices.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow drivers or rate control algorithms to specify BlockAck session
timeout when initiating an ADDBA transaction. This is useful in cases
where maintaining persistent BA sessions does not incur any overhead.
The current timeout value of 5000 TUs is retained for all non ath9k/ath9k_htc
drivers.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
patch "iwlagn: check ready in iwlagn_bss_info_changed()" introduce
whitespace, fix it
please merge with the previous patch
Reported by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows the pm-qos value to be user configurable by making it as
a module parameter.This will help our customers to configure the pm-qos
value according to the effect in throughput due to the DMA latency problem
which was observed in Intel Pinetrail platforms.
The tested value of '55' will be filled as the default
pm-qos-value incase the user does not specifies pm-qos value as a
module parameter.
example usage: sudo modprobe ath9k pmqos=65
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change some file names and Kconfig settings so that this new module matches
the new way of using wl12xx instead of wl1271.
Also fix SDIO power enabling and disabling to match the latest way of doing
it.
Cc: Roger Quadros <roger.quadros@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
With the current single-queue implementation traffic priorization is not
working correctly - when using multiple BE streams and one, say VI stream,
the VI stream will share bandwidth almost equally with the BE streams.
To fix the issue, implement per AC queues, which are emptied in priority
order to the firmware. To keep it relatively simple, maintain a global
buffer count and global queue stop/wake instead of per-AC.
With these changes, priorization appears to work just fine.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Currently, the debug level is set in compilation time (by the DEBUG_LEVEL
const). This method has the advantage of compiling only the relevant
messages, while optimizing out the unused ones.
In order to allow runtime control over the debug_level, while optimizing
out messages when debug messages are not needed, we combine some methods:
1. use dynamic_debug (pr_debug) rather then printk.
2. add debug_level module param in order to set debug level during insmod.
3. add debug_level sysfs file in order to allow dynamic control over the
debug level.
Since patches for pr_debug_hex_dump() implementation haven't been applied yet,
we are still temporarly using print_hex_dump().
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Inclusion of a WPS IE in probe requests caused a problem
in the driver due to the maximum size of the probe request
template and the max_scan_ie_len values at initialization.
Increased the size of probe request template
to the maximum size allowed by the firmware.
Struct wl12xx_probe_req_template, which was only used
for calculating the max size of the probe request template,
is no longer used and needed.
max_scan_ie_len is used for validating the size of
additional IEs in scan requests.
Initialized the max_scan_ie_len field to the maximum size
of the probe request template minus the ieee80211 header size.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
The auto-arp feature of wl12xx allows the firmware to automatically
response to arp requests asking for its ip.
in order to use it, we configure the arp response template and
enable the corresponding bit in wl1271_acx_arp_filter (along with
passing its ip)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
This module enables individually generating RX and TX traffic
over the SDIO bus on which the WL1271 chipset is connected.
This is required to perform RF interference testing.
The module takes 2 module parameters 'rx' and 'tx'.
To generate RX traffic:
modprobe wl1271_sdio_test rx=1
To generate TX traffic:
modprobe wl1271_sdio_test tx=1
To generate both RX & TX traffic, set both rx and tx to 1.
You can change the testing configuration at runtime by changing
the rx & tx values at /sys/modules/wl1271_sdio_test/
To stop testing simply unload the module.
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Reviewed-by: Carlos Chinea <carlos.chinea@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Disabling the 11a channels when not supported in the reg_notify function was
not working as it should, because when the driver is initiailizing (and
registering itself with mac80211), it would get the reg notification too
early. At that point the driver wouldn't have received the NVS yet, so it
wouldn't know whether 11a was supported.
To fix this, we disable 11a channels when we read the NVS instead. Also, it
is easier (and still safe) to set n_channels to zero instead of setting the
disabled flag on every 11a channel.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
This USB ID is for the WUBI-100GW 802.11g Wireless LAN USB Device that
uses p54usb.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Eduardo Costa <ecosta.tmp@gmail.com>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Multiple devices use almost the same .cfg with minor differences.
Use macro and remove the duplication. By doing this, reduce
the chance for mistake while modify .cfg parameters
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
For WiFi/WiMAX combo devices, if WiMAX own the RF, WiFi driver
try to access RF and fail. This is the W/A to To avoid WiFi keep
reloading firmware and try to access RF again.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
For logging EEPROM related info, instead of using IWL_DEBUG_INFO,
use the dedicated logging (IWL_DEBUG_EEPROM) for easier debugging
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This removes the old TX power reading code, it isn't
necessary since the new code is able to read all the
various EEPROM layouts due to relying on information
contained in the EEPROM.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The current EEPROM reading code has some layout
assumptions that now turned out to be false with
some newer versions of the EEPROM. Luckily, we
can avoid all such assumptions by using data in
the EEPROM itself, so implement using that.
However, for risk mitigation purposes, keep the
old reading code for current hardware for now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Some fields we didn't previously use from the
enhanced TX power structure will be needed in
the next patch, so rename them to their correct
names to be able to use them and change code
reading them accordingly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
For the new 1x1 devices, hw and uCode will support rx
antenna diversity, but we need to indicate 1x1 device to
AccessPoint to make sure it won't use MIMO.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The compiler correctly warns:
iwl-agn-tx.c: In function ‘iwlagn_tx_status_reply_compressed_ba’:
iwl-agn-tx.c:1240: warning: ‘bitmap’ may be used uninitialized in this function
Move the debug print to the branch that reads the
bitmap, and move the variables too so it's more
obvious where they are needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
In function iwlagn_bss_info_changed(), we need to check if the driver
is ready before doing real work. Also, the previously put WARN() is
removed because the vif is not guaranteed to be valid. uCode restart
routine will clear the vif.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This prevent bad fixed_rate keeps crashing uCode in an endless loop.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Commit 6175ddf06b changes the way
memcpy_toio() works for x86_64, causing firmware loading to fail for
some Ralink WLAN devices with the rt2800pci driver since linux 2.6.34.
This causes the log message: "phy0 -> rt2800pci_load_firmware: Error -
PBF system register not ready.".
Fix this by using __iowrite32_copy instead of memcpy_toio().
Signed-off-by: Wolfgang Kufner <wolfgang.kufner@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pad beacon to a multiple of 32 bits in preparation for the change
from memcpy_toio() to __iowrite32_copy() in register_multiwrite().
Signed-off-by: Wolfgang Kufner <wolfgang.kufner@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The stray semicolon after DEBUG_PRINTK_MSG causes things
like "if (...) WARNING(...); else {}" to fail with syntax error.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Queue names were incorrectly copied from the legacy drivers,
as a result the queue names were inversed to what was expected.
This renames the queues using this mapping:
QID_AC_BK -> QID_AC_VO (priority 0)
QID_AC_BE -> QID_AC_VI (priority 1)
QID_AC_VI -> QID_AC_BE (priority 2)
QID_AC_VO -> QID_AC_BK (priority 3)
Note that this was a naming problem only, which didn't affect
the assignment of frames to their respective queues.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a queue entry flag ENTRY_DATA_STATUS_PENDING,
which can be used to indicate a queue entry has
returned from the hardware and is waiting for
status processing. Using this flag we can add
some extra sanity checks to prevent queue corruption.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the rt2x00_dmastart function to rt2x00lib which
marks the queue_entry as "owned by device", and increased
the Q_INDEX number.
This cleanups up the index handling by rt2x00lib which
at until so far used hackish approaches to keep the
RX queue index numbering sane.
The rt2x00pci.c changes are from Helmut Schaa
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new command to the queue handlers: "flush",
this moves the flush() callback from mac80211
into rt2x00queue and adds support for flushing
the RX queue as well.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add wrapper functions in rt2x00queue.c to
start & stop queues. This control must be protected
using a mutex.
Queues can also be paused which will halt the flow
of packets between the driver and mac80211. This doesn't
require a mutex protection.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As part of the queue refactoring, change the queue callback
function names to have 3 different actions: start, kick & stop.
We can now also remove the STATE_RADIO_RX_ON/STATE_RADIO_RX_OFF
device_state flags, and replace the usage with using the
start_queue/stop_queue callback functions.
This streamlines the RX queue handling to the
similar approach as all other queues.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As part of the queue refactoring, we now introduce
3 queue commands: start, kick, stop.
- Start: will enable a queue, for TX this will
not mean anything, while for beacons and RX
this will update the registers to enable the queue.
- Kick: This will kick all pending frames to
the hardware. This is needed for the TX queue
to push all frames to the HW after the queue
has been started
- Stop: This will stop the queue in the hardware,
and cancel any pending work (So this doesn't
mean the queue is empty after a stop!).
Move all code from the drivers into the appropriate
functions, and link those calls to the old rt2x00lib
callback functions (we will fix this later when we
refactor the queue control inside rt2x00lib).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 0204464329 "Check for specific changed
flags when updating the erp config" changed the way in which a new beacon
interval gets handled. However, due to a bug in rt2800usb and rt2800pci the
beacon interval was reset during each scan, thus causing problems in AdHoc
mode.
Fix this by not cleaning up the beacon interval when killing the beacon queue
but just prevent the device from sending out beacons.
Reported-by: Wolfgang Kufner <wolfgang.kufner@gmail.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent changes to the TX-done code of rt2x00 resulted in TX-ed frames not
being returned to mac80211 in the original state, and therefore with
insufficient headroom for re-transmissions.
Fix this by reverting the changes done and by ensuring we remove the inserted
L2pad by moving the header backwards instead of the data forwards.
At the same time also make sure that the rt2x00queue_remove_l2pad will not
move any memory when a frame has no data at all.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Jay Hung <Jay_Hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an rt2x00 USB device is unplugged while in use, it reliably
hangs the whole system. After some time the watchdog prints:
BUG: soft lockup - CPU#0 stuck for 64s! [kworker/u:0:5]
...
[<c01a88d8>] (usb_submit_urb+0x0/0x2ac) from [<bf0e752c>] (rt2x00usb_kick_rx_entry+0xb4/0xe8 [rt2x00usb])
[<bf0e7478>] (rt2x00usb_kick_rx_entry+0x0/0xe8 [rt2x00usb]) from [<bf0e7588>] (rt2x00usb_clear_entry+x28/0x2c [rt2x00usb])
[<bf0e7560>] (rt2x00usb_clear_entry+0x0/0x2c [rt2x00usb]) from [<bf0d5bc4>] (rt2x00lib_rxdone+0x2e0/0x2f8 [rt2x00lib])
[<bf0d58e4>] (rt2x00lib_rxdone+0x0/0x2f8 [rt2x00lib]) from [<bf0e7e00>] (rt2x00usb_work_rxdone+0x54/0x74 [rt2x00usb])
[<bf0e7dac>] (rt2x00usb_work_rxdone+0x0/0x74 [rt2x00usb]) from [<c00542b4>] (process_one_work+0x20c/0x35c)
Clear the DEVICE_STATE_PRESENT flag when usb_submit_urb()
returns -ENODEV to fix this.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add RF chip definition
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement the get_survey callback to allow user space to read statistics
about the current channel condition.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add and modify NIC Configuration and LED definition of EEPROM
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduces the likelihood of false pulse detects in the hardware
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The EEPROM contains scale factors for the tx power, which define
the range of allowable difference between target power and training
power. If the difference is too big, PA predistortion cannot be used.
For 2.4 GHz there is only one scale factor, for 5 GHz there are
three, depending on the specific frequency range.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The EEPROM PAPRD rate mask fields only contain mask values for actual
rates in the low 25 bits. The upper bits are reserved for tx power
scale values. Add the proper mask definitions and use them before
writing the values to the register.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To be able to measure the thermal values correctly for PAPRD, we need
to send training frames before setting up the gain table for the measurement,
and then again afterwards for the actual training.
For further improvement, send training frames at MCS0 instead of 54 MBit/s
legacy. That way we can use the No-ACK flag for the transmission, which
speeds up PAPRD training in general, as the hardware won't have to
retransmit and wait for ACK timeout (was previously set to 4 * 6
transmission attempts).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Testing shows that adjusting the slot time based on the coverage class
produces very high latencies and very low throughput on long distance links.
Adjusting only the ACK timeout and leaving the slot time at the regular
values - while technically not optimal for CSMA - works a lot better on
long links (tested with 10 km distance)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(u32) -1 is not particularly useful as a slottime default, so even though
the ath9k_hw default should never get used, it's better to pick something
sane here.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to have separate callbacks for pre-AR9003 vs AR9003
SREV version checks, so just merge those into one function.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9280 based hardware with 3 antennas and slow antenna diversity has
not been seen in the wild and ath9k does not support that form of
antenna diversity, so remove the EEPROM ops for it.
These EEPROM ops are currently only used for setting the
AR_PHY_SWITCH_COM register, which is being done in the EEPROM specific
file already.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also add a comment about a potential array overrun that needs to
be reviewed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Newer chips do not need this, and maybe these register writes could have
negative side effects on newer hardware.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wireless-testing commit 04caf86375
('ath9k: more tx setup cleanups') merged tx path code for HT vs
non-HT frames, however it did not pass the tid pointer to
ath_tx_send_normal, causing an inconsistency between AMPDU vs
non-AMPDU sequence number handling.
Fix this by always passing in the tid pointer for all QoS data frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter