Up to now, the driver was simply assuming TV mode, 13 segs.
Implement the logic to control the ISDB operational mode.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Putting em28xx in suspend mode when a feed stops is just plain
wrong. Every time a new PES filter is changed, the DVB demux
code will stop the current feed, and then start a new one.
If are there any code that switches off the frontend, via
some GPIO setting, this would make the DVB fail.
This condition was actually trigged with one device, during
DVB scan, as, during scan, it is common that userspace apps
to change the filter several times, in order to get all
tables.
Also, this is not needed at all, since the em28xx code already
hooks into ops.ts_bus_ctrl(). This warrants that em28xx can
check there if DVB frontend is in usage or not. The code there
already puts the device on suspend mode, if the DVB frontend
is not used (closed).
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using 3.3 MHz IF, use 4MHz. That's the standard
value for the demod, and, while it can be adjusted, 3.3 MHz
is out of the recommended range. So, let's stick with the
default.
With regards to the IF voltage level, instead of using
0.5 V(p-p) for IF, use 2V, giving a 12dB gain.
The rationale is that, on PixelView SBTVD Hybrid,
even 2V(p-p) would be in the nominal range for IF,
as the maximum range on this particular device is 3V.
A higher gain here should help to improve reception under
weak signals.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signal strength is always available. There's no reason to reset
it, as it has its own logic to reset it already.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Always init the frontend when set_frontend is called. The rationale
is: it was noticed that, on some devices, it fails to lock with a
different channel. It seems that some other registers need to be
restored to its initial state, when the channel changes.
As it is better to reset everything, even wasting a few more
miliseconds than to loose channel lock, let's change the logic
to always reset.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the AGC settings present on a newer device.
The initial settings were taken from one of the first devices with
mb86a20s, and there are several reports that this is not working
properly on some places.
So, instead of keeping using it, get the parameters taken from a
newer device. Tests are welcomed.
Tested also with cx231xx PixelView SBTVD Hybrid with no regressions
noticed so far.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
State 9 means TS started to be output, and it should be
associated with FE_HAS_SYNC.
The mb86a20scan get CNR statistics at state 7, when frame sync
is obtained.
As CNR may help to adjust the antenna, provide it earlier.
A latter patch could eventually start outputing MER measures
earlier, but that would require a bigger change, and probably
won't be better than the current way, as the time between
changing from state 8 to 9 is generally lower than the time
to get the stats collected.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of hardcoding a fixed IF frequency of 3.3 MHz, use
the IF frequency provided by the tuner driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are a few debug tests that are shown with dev_err() or
dev_info(). Replace them by dev_dbg().
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new eeproms with 16 address width still have the the device config dataset
(the content of the old 8 bit eeproms) embedded.
Hauppauge also continues to include the tveeprom data structure inside this
dataset in their devices.
The start address of the dataset depends on the start address of the microcode
and a variable additional offset.
It should be mentioned that Camera devices seem to use a different dataset type,
which is not yet supported.
Tested with devices "Hauppauge HVR-930C". I've also checked the USB-log from the
"MSI Digivox ATSC" and it works the same way.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We currently reserve an array of 256 bytes for the eeprom content in the device
struct. For eeproms with 16 bit address width it might even be necessary to
increase the buffer size further.
Having such a big chunk of memory reserved even if the device has no eeprom and
keeping it after it has already been processed seems to be a waste of memory.
Change the code to allocate + free the eeprom memory dynamically.
This also makes it possible to handle different dataset sizes depending on what
is stored/found in the eeprom.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a helper function for reading data blocks from i2c devices with 8 or 16 bit
address width and 8 bit register width.
This allows us to reduce the size of new code added by the following patches.
Works only for devices with activated register auto incrementation.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Newer devices (em2874, em2884, em28174, em25xx, em27[6,7,8]x) use eeproms with
16 bit instead of 8 bit address width.
The used eeprom type depends on the chip type, which makes sure eeproms can't
be damaged.
This patch adds basic support for 16 bit eeproms only, which includes
- reading the content
- calculating the eeprom hash
- displaying the content
The eeprom content uses a different format, for which support will be added with
subsequent patches.
Tested with the "Hauppauge HVR-930C" and the "Speedlink VAD Laplace webcam"
(with additional experimental patches).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The data is stored as little endian in the eeprom.
Hence the correct data types should be used and the data should be converted
to the machine endianess before using it.
The eeprom id (key) also isn't a 32 bit value but 4 separate bytes instead.
[mchehab@redhat.com: Fix CodingStyle]
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the eeprom key isn't valid, either a different (currently unknown) format
is used or the eeprom is corrupted.
In both cases it doesn't make sense to interpret the data.
Also print an error message.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current code uses only a single debug level and all debug messages are
printed for i2c_debug >= 2 only. So debug level 1 is actually the same as
level 0, which is odd.
Users expect debugging messages to become enabled for anything else than
debug level 0.
Fix it and simplify the code a bit by printing the debug messages also at debug
level 1;
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reduces the number of characters/lines, unifies the code and improves readability.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is only a single place where the dprintk2 macro is used, so get rid of it.
[mchehab@redhat.com: fix checkpathc.pl complain:
ERROR: space prohibited before that close parenthesis ')']
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em28xx driver has changed much, especially since kernel 3.8.
So it's time to bump the driver version.
Changes since kernel 3.8:
- converted the driver to videobuf2
- converted the driver to the v4l2-ctrl framework
- added USB bulk transfer support
- use USB bulk transfers by default for webcams (allows streaming from multiple devices at the same time)
- added image quality bridge controls: contrast, brightness, saturation, blue balance, red balance, sharpness
- removed dependency from module ir-kbd-i2c
- cleaned up the frame data processing code
- removed some unused/obsolete code
- made remote controls of devices with external (i2c) receiver/decoder work again
- fixed audio over USB for device "Terratec Cinergy 250"
- several v4l2 compliance fixes and improvements (including fixes for ioctls enabling/disabling)
- lots of further bug fixes and code improvements
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the image quality bridge controls contrast, brightness, saturation,
blue balance, red balance and sharpness.
These controls are enabled only if no subdevice provides them.
Tested with the following devices:
"Terratec Cinergy 200 USB"
"Hauppauge HVR-900"
"SilverCrest 1.3MPix webcam"
"Hauppauge WinTV USB2"
"Speedlink VAD Laplace webcam"
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The image quality default values will be used in at least two different places
and by using #defines we make sure that they are always consistent.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Output resolutions <=20% of the input resolution exceed the capabilities of the
scaler.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The maximum supported scaling value for registers 0x30+0x31 (horizontal scaling)
and 0x32+0x33 (vertical scaling) is 0x3fff, which corresponds to 20% of the
input frame size.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Avoids registering a VBI device and streaming in VBI-mode if the device is a
camera.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_DBG_G_CHIP_IDENT is a "normal" and not an "advanced" debug functionality.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_device_disconnect() is called when the device is disconnected, so that the
v4l2-core rejects all ioctl calls.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tuner type is set by the v4l2-core based on the device type.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
vidioc_s_fmt_vbi_cap() is a 100% duplicate of vidioc_g_fmt_vbi_cap() and
therefore can be removed.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em28xx driver doesn't support the VIDIOC_G_CROP and VIDIOC_S_CROP ioctls,
so VIDIOC_CROPCAP is useless and has the potential to confuse applications,
because it can be interpreted as indicator for cropping support.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the current code V4L2_BUF_TYPE_VIDEO_CAPTURE is accepted only, but for VBI
devices only buffer type V4L2_BUF_TYPE_VBI_CAPTURE is used/valid.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_S_PARM doesn't make sense for VBI device nodes, because we don't support
selecting the number of read buffers to use.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of checking the device type and returning -ENOTTY inside the ioctl
function, use v4l2_disable_ioctl() to disable the ioctl VIDIOC_S_PARM if the
device is not a camera.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of checking the device type and returning -EINVAL inside the ioctl
functions, use v4l2_disable_ioctl() to disable the ioctls VIDIOC_G_AUDIO and
VIDIOC_S_AUDIO if the device doesn't support audio.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Disable the ioctls VIDIOC_G_TUNER, VIDIOC_S_TUNER, VIDIOC_G_FREQUENCY and
VIDIOC_S_FREQUENCY for video and VBI devices without tuner.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of checking the device type and returning -ENOTTY inside the ioctl
functions, use v4l2_disable_ioctl() to disable the ioctls VIDIOC_QUERYSTD,
VIDIOC_G_STD and VIDIOC_S_STD if the device is a camera.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRM9iWAAoJEHm+PkMAQRiGb4AH/0a99dPoENe40AnRdthsPgKN
47n8L+Apra16PoOs3zAv+oWd1NskfIhaO2UVllKMkWBgiH6/FttJAprVQXJBVpiq
WWv7BKtI2lyHmiPbQohY6K2nvpami/WwblISxvaU13NhlCJ2ubSFPfGtNQAkx6vn
DH/GKfPDFayVmFiOQ8TFvVqFmWvn4m3ttIQYEEJHtjY2h3+2Z43xdIRXo7byqSTl
9cf3FQjIihLLuQ1Hua2HkFh7dQT5/hNSrbf6afaSjCgW2cGj7mRTuvxWZgm7eVpg
rksFN92EnFs/RJQBK6ZxfYhCMqV5ImUletKfsnQoxl+3NbPQjO0wl7R9VXbC7SE=
=pBPB
-----END PGP SIGNATURE-----
Merge tag 'v3.9-rc1' into staging/for_v3.9
Linux 3.9-rc1
* tag 'v3.9-rc1': (10698 commits)
Linux 3.9-rc1
btrfs/raid56: Add missing #include <linux/vmalloc.h>
fix compat_sys_rt_sigprocmask()
SUNRPC: One line comment fix
ext4: enable quotas before orphan cleanup
ext4: don't allow quota mount options when quota feature enabled
ext4: fix a warning from sparse check for ext4_dir_llseek
ext4: convert number of blocks to clusters properly
ext4: fix possible memory leak in ext4_remount()
jbd2: fix ERR_PTR dereference in jbd2__journal_start
metag: Provide dma_get_sgtable()
metag: prom.h: remove declaration of metag_dt_memblock_reserve()
metag: copy devicetree to non-init memory
metag: cleanup metag_ksyms.c includes
metag: move mm/init.c exports out of metag_ksyms.c
metag: move usercopy.c exports out of metag_ksyms.c
metag: move setup.c exports out of metag_ksyms.c
metag: move kick.c exports out of metag_ksyms.c
metag: move traps.c exports out of metag_ksyms.c
metag: move irq enable out of irqflags.h on SMP
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAUNNNlBOxKuMESys7AQKLmw//TQ8NRe7PGpsKpApuCVePmmIicGv9f9C2
5Upovfl1Um144jDzpNDuvM+txzrZvh9riaLYbqvoWGUlP4kbX9VsMA6fJcLonUEk
G9/RtdijZzhlNL59mhoLxUWJi5/jK8TAgStJmJ7TkZFFc8r0QXlHcx5+lClrYLAv
jTkPlIqm9YhzeayOOPmbrI1lxgPJrf6MZ9BJh4cz93VPqKmYvA69/dqJAO/1JBHW
YmWfzHy7NTchdWbw0+vGPlsX0xe5ymTl5reY94H23AxGhOB1CqiXqXyy4CyjaQ8g
sxkhDJFmgA6+OyJQeG98lmcVV5heY0h4AizHvIuwnUZzIgXF2ipWMp1zhJf8yX9/
wQQBtN0VZ9QGdo6lMzFd2jzqkVtYMyYuDasMb4OGVGtX/0w95j7uvRXjPEkRl21e
B4In9VqYp8yKusPwGgHd4NkSUJS/iqg7FknkiOL/OI6rjqfF5/Ot2yL2Mhp7ozh+
I8hflc2BaKv29UNRPAnI6Z2GngylLF0E4fvxU4E/L8EUwi7O3UxYqerT9fUDodrM
xSdAlWK+iNBURo9G8/Au3XNpJwSAMYTBMJf0RevI7QpxqxYvjdygX+jiqfzH4x3A
SMDeeSIsipbVJxZgCzRngQl/yPD/Cu3bRBBTV3Y8vVxt2Fv5vJBQ8pXhBBrcyx8M
Wuoyk58CGaw=
=JMlx
-----END PGP SIGNATURE-----
Merge tag 'disintegrate-fbdev-20121220' of git://git.infradead.org/users/dhowells/linux-headers
Pull fbdev UAPI disintegration from David Howells:
"You'll be glad to here that the end is nigh for the UAPI patches.
Only the fbdev/framebuffer piece remains now that the SCSI stuff has
gone in.
Here are the UAPI disintegration bits for the fbdev drivers. It
appears that Florian hasn't had time to deal with my patch, but back
in December he did say he didn't mind if I pushed it forward."
Yay. No more uapi movement. And hopefully no more big header file
cleanups coming up either, it just tends to be very painful.
* tag 'disintegrate-fbdev-20121220' of git://git.infradead.org/users/dhowells/linux-headers:
UAPI: (Scripted) Disintegrate include/video
- Update the Xen ACPI memory and CPU hotplug locking mechanism.
- Fix PAT issues wherein various applications would not start
- Fix handling of multiple MSI as AHCI now does it.
- Fix ARM compile failures.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQEcBAABAgAGBQJRMM+8AAoJEFjIrFwIi8fJnGsIANU/lVS5EwV6ZMP9GiVtbm68
sBn0MoDIkN2ID16gcrQdfvzgtTQHsptL2fOl756veTHN2AIpIFYShKZpbgR9VM+c
MpD68ltakkfjoVeb7F7yPbDvcSftKRW5VAq1SeFMc2gOOmiqAWQGgBC+3Cd04zFk
SqzDs1RLUHypwBOFlZKa1ex/ShuYfzRb9x+J6zqGO+OpjhlMobyag8rhSlgehlfP
6gS1IzmcH8a6SgBKZk/+YC+i+QLgPOyxiK6zcxa2rfc6iUwodpqBpKP1N+CS4lnu
FIKOIIzzCwCEAq94wVV0GJwHyw7nsqjG8syfRyOPmauLrpOI70xrV+lYFMVVRA0=
=HwzV
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.9-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
- Update the Xen ACPI memory and CPU hotplug locking mechanism.
- Fix PAT issues wherein various applications would not start
- Fix handling of multiple MSI as AHCI now does it.
- Fix ARM compile failures.
* tag 'stable/for-linus-3.9-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xenbus: fix compile failure on ARM with Xen enabled
xen/pci: We don't do multiple MSI's.
xen/pat: Disable PAT using pat_enabled value.
xen/acpi: xen cpu hotplug minor updates
xen/acpi: xen memory hotplug minor updates
Pull more VFS bits from Al Viro:
"Unfortunately, it looks like xattr series will have to wait until the
next cycle ;-/
This pile contains 9p cleanups and fixes (races in v9fs_fid_add()
etc), fixup for nommu breakage in shmem.c, several cleanups and a bit
more file_inode() work"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
constify path_get/path_put and fs_struct.c stuff
fix nommu breakage in shmem.c
cache the value of file_inode() in struct file
9p: if v9fs_fid_lookup() gets to asking server, it'd better have hashed dentry
9p: make sure ->lookup() adds fid to the right dentry
9p: untangle ->lookup() a bit
9p: double iput() in ->lookup() if d_materialise_unique() fails
9p: v9fs_fid_add() can't fail now
v9fs: get rid of v9fs_dentry
9p: turn fid->dlist into hlist
9p: don't bother with private lock in ->d_fsdata; dentry->d_lock will do just fine
more file_inode() open-coded instances
selinux: opened file can't have NULL or negative ->f_path.dentry
(In the meantime, the hlist traversal macros have changed, so this
required a semantic conflict fixup for the newly hlistified fid->dlist)
Mauro Carvalho Chehab