This patch does two things related to reading the factory badblock table during
initialization: (1) fix error where a non-zero return code from
docg4_read_page() is assumed to be an error (it was later changed to be
max_bitflips; thanks to Brian Norris for bringing this to my attention a while
back), and (2) if there is an error reading the factory bbt, it tries reading
another (redundant) factory bbt table.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Modify the nand_ecclayout to place the two bb marker bytes in the oob region
off-limits to the user.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The controller on the docg4 has a "reliable" mode, where consecutive 2k pages
are used in parallel. The initial program loader (IPL) on my Treo 680 expects
the secondary program loader (SPL) to be written in this mode. This patch adds
support for writing data in reliable mode, by way of a module parameter.
Support for reading in this mode (as the IPL does) is not supported yet, but
alternate (even-numbered) 2k pages written in reliable mode can be read normally
(odd-numbered pages will contain junk and generate ecc errors).
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Currently the docg4's ecc.read_page() method returns -EBADMSG when
uncorrectable bitflips occur. This is wrong; 0 should be returned in
this case. An error code should only be returned by this method in the
case of a hardware error (probably -EIO).
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch does two closely related things:
(1) Currently the ecc.read_page() method does not fill the nand->oob_poi buffer
with the oob data, but instead reads oob into a local buffer. Fix this by
filling the oob_poi buffer instead of a local buffer. The 'oob_required'
argument is quietly ignored; the device must always read oob after the page
data, and it is presumed that there's no harm in filling oob_poi, even when not
explicitly requested.
(2) Always read oob from the device in ecc.read_oob(), instead of copying it
from a local buffer under some circumstances.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There is an implemention of hardware ECC write page function which may return an
error indication.
For instance, using Atmel HW PMECC to write one page into a nand flash, the hardware
engine will compute the BCH ecc code for this page. so we need read a the
status register to theck whether the ecc code is generated.
But we cannot assume the status register always can be ready, for example,
incorrect hardware configuration or hardware issue, in such case we need
write_page() to return a error code.
Since the definition of 'write_page' function in struct nand_ecc_ctrl is 'void'.
So this patch will:
1. add return 'int' value for 'write_page' function.
2. to be consitent, add return 'int' value for 'write_page_raw' fuctions too.
3. add code to test the return value, and if negative, indicate an
error happend when write page with ECC.
4. fix the compile warning in all impacted nand flash driver.
Note: I couldn't compile-test all of these easily, as some had ARCH dependencies.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
As of [mtd: nand: remove autoincrement 'sndcmd' code], the
NAND_CMD_READ0 command is issued unconditionally.
Thus, read_oob/read_oob_raw's 'sndcmd' argument is no longer needed, as
well as their return code.
Remove the 'sndcmd' parameter, and set the return code to 0.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
New NAND controllers can perform read/write via HW engines which don't expose
OOB data in their DMA mode. To reflect this, we should rework the nand_chip /
nand_ecc_ctrl interfaces that assume that drivers will always read/write OOB
data in the nand_chip.oob_poi buffer. A better interface includes a boolean
argument that explicitly tells the callee when OOB data is requested by the
calling layer (for reading/writing to/from nand_chip.oob_poi).
This patch adds the 'oob_required' parameter to each relevant {read,write}_page
interface; all 'oob_required' parameters are left unused for now. The next
patch will set the parameter properly in the nand_base.c callers, and follow-up
patches will make use of 'oob_required' in some of the callee functions.
Note that currently, there is no harm in ignoring the 'oob_required' parameter
and *always* utilizing nand_chip.oob_poi, but there can be
performance/complexity/design benefits from avoiding filling oob_poi in the
common case. I will try to implement this for some drivers which can be ported
easily.
Note: I couldn't compile-test all of these easily, as some had ARCH
dependencies.
[dwmw2: Merge later 1/0 vs. true/false cleanup]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Jiandong Zheng <jdzheng@broadcom.com>
Acked-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
No drivers use auto-increment NAND, so kill the NO_AUTOINCR option entirely.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The ecc.read_page() method for nand drivers is changed to return the maximum
number of bitflips that were corrected on any one region covering an ecc step,
This patch doesn't change what the nand code returns to mtd.
This v2 includes the change to the fsl_ifc_nand driver requested by Scott¹.
¹ http://lists.infradead.org/pipermail/linux-mtd/2012-April/040883.html
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Acked-by (freescale changes): Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Flash device drivers initialize 'ecc_strength' in struct mtd_info, which is the
maximum number of bit errors that can be corrected in one writesize region.
Drivers using the nand interface intitialize 'strength' in struct nand_ecc_ctrl,
which is the maximum number of bit errors that can be corrected in one ecc step.
Nand infrastructure code translates this to 'ecc_strength'.
Also for nand drivers, the nand infrastructure code sets ecc.strength for ecc
modes NAND_ECC_SOFT, NAND_ECC_SOFT_BCH, and NAND_ECC_NONE. It is set in the
driver for all other modes.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Gcc complains here:
drivers/mtd/nand/docg4.c: In function ‘probe_docg4’:
drivers/mtd/nand/docg4.c:1277:4: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3 has type ‘resource_size_t’ [-Wformat]
drivers/mtd/nand/docg4.c:1277:4: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 4 has type ‘resource_size_t’ [-Wformat]
We have a standard way of printing these using a format string
extension.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds a driver for the M-Sys / Sandisk diskonchip G4 nand flash found
in various smartphones and PDAs, among them the Palm Treo680, HTC Prophet and
Wizard, Toshiba Portege G900, Asus P526, and O2 XDA Zinc. It was tested on the
Treo 680, but should work generically.
Since v3, this patch adds power management functions, a scan of the factory bad
block table during initialization, several fixes, and more extensive testing.
Also, the platform data header file, which only contained partitioning
information, was removed. Command-line partitioning can be used, at least until
an mtd parser is written for the saftl format with which these chips are
shipped.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Mike Dunn