The address limit is already set in flush_old_exec() so this
set_fs(USER_DS) is redundant.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The documentation for the IMDMA channels appears to be incorrect.
These DMA blocks don't actually have PERIPHERAL_MAP MMRs for us
to access. Attempts to do so lead to system mmr hardware errors.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Blackfin mutex.h is merely a copy of an older asm-generic/mutex-dec.h,
so punt it and just use the common one directly.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This moves the double fault data used at boot time into a single struct
which can then easily be addressed with indexed loads rather than having
to explicitly load multiple addresses.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The default for the Blackfin SPI driver is 8 bits and dma disabled,
so many of the bfin5xx_spi_chip resources are redundant. So punt
those parts.
Further, drivers should themselves be declaring 16 bit transfers,
so for those that do, and for the ones which no longer do 16 bit
transfers, drop the bfin5xx_spi_chip resources.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The jump to 4f will cause the NUL padding loop to run at least one time,
so if string length is zero just jump to the end. Otherwise we wrongly
write one NUL byte when size==0.
Signed-off-by: Steven Miao <realmz6@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The documentation is a little iffy as to whether these are actual MMRs,
but reading them on the hardware works, and the previous version of this
logic (the SDH) had PID[4567]. So add it for RSI too.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Looks like the copying of MMR defines from the SDH block missed updating
the addresses of the RSI_PID# registers. So tweak them to reflect the
actual hardware.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The bf52x/bf54x have the incorrect addresses for USB_EP_NI7_RXINTERVAL
and USB_EP_NI7_TXCOUNT, so adjust those.
Further, the bf54x header puts the USB defines in the wrong place, so
shuffle them back to the right grouping.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This code was mostly developed against a BF54x, so some BF537-specific
issues were missed.
The PPI block starts at PPI_CONTROL, not PPI_STATUS (which is the reverse
of the EPPI block).
The MDMA block starts at MDMA_NEXT_DESC_PTR, not MDMA_CONFIG. Seems the
sim does not catch misreads here so that'll need to get fixed.
The gptimer block is mostly 32bit regs, not 16bit. Use the gptimer struct
to figure that out rather than hardcoding it locally.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Now that the serial code has been unified in bfin_serial.h, and the
Blackfin UART driver pushed its resources to the boards files, we
don't need these headers anymore.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Any consumer that needs to access the MMRs has to provide these helpers,
so make the default into useless stubs.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (25 commits)
perf: Fix SIGIO handling
perf top: Don't stop if no kernel symtab is found
perf top: Handle kptr_restrict
perf top: Remove unused macro
perf events: initialize fd array to -1 instead of 0
perf tools: Make sure kptr_restrict warnings fit 80 col terms
perf tools: Fix build on older systems
perf symbols: Handle /proc/sys/kernel/kptr_restrict
perf: Remove duplicate headers
ftrace: Add internal recursive checks
tracing: Update btrfs's tracepoints to use u64 interface
tracing: Add __print_symbolic_u64 to avoid warnings on 32bit machine
ftrace: Set ops->flag to enabled even on static function tracing
tracing: Have event with function tracer check error return
ftrace: Have ftrace_startup() return failure code
jump_label: Check entries limit in __jump_label_update
ftrace/recordmcount: Avoid STT_FUNC symbols as base on ARM
scripts/tags.sh: Add magic for trace-events for etags too
scripts/tags.sh: Fix ctags for DEFINE_EVENT()
x86/ftrace: Fix compiler warning in ftrace.c
...
32bit and 64bit on x86 are tested and working. The rest I have looked
at closely and I can't find any problems.
setns is an easy system call to wire up. It just takes two ints so I
don't expect any weird architecture porting problems.
While doing this I have noticed that we have some architectures that are
very slow to get new system calls. cris seems to be the slowest where
the last system calls wired up were preadv and pwritev. avr32 is weird
in that recvmmsg was wired up but never declared in unistd.h. frv is
behind with perf_event_open being the last syscall wired up. On h8300
the last system call wired up was epoll_wait. On m32r the last system
call wired up was fallocate. mn10300 has recvmmsg as the last system
call wired up. The rest seem to at least have syncfs wired up which was
new in the 2.6.39.
v2: Most of the architecture support added by Daniel Lezcano <dlezcano@fr.ibm.com>
v3: ported to v2.6.36-rc4 by: Eric W. Biederman <ebiederm@xmission.com>
v4: Moved wiring up of the system call to another patch
v5: ported to v2.6.39-rc6
v6: rebased onto parisc-next and net-next to avoid syscall conflicts.
v7: ported to Linus's latest post 2.6.39 tree.
> arch/blackfin/include/asm/unistd.h | 3 ++-
> arch/blackfin/mach-common/entry.S | 1 +
Acked-by: Mike Frysinger <vapier@gentoo.org>
Oh - ia64 wiring looks good.
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.infradead.org/mtd-2.6: (97 commits)
mtd: kill CONFIG_MTD_PARTITIONS
mtd: remove add_mtd_partitions, add_mtd_device and friends
mtd: convert remaining users to mtd_device_register()
mtd: samsung onenand: convert to mtd_device_register()
mtd: omap2 onenand: convert to mtd_device_register()
mtd: txx9ndfmc: convert to mtd_device_register()
mtd: tmio_nand: convert to mtd_device_register()
mtd: socrates_nand: convert to mtd_device_register()
mtd: sharpsl: convert to mtd_device_register()
mtd: s3c2410 nand: convert to mtd_device_register()
mtd: ppchameleonevb: convert to mtd_device_register()
mtd: orion_nand: convert to mtd_device_register()
mtd: omap2: convert to mtd_device_register()
mtd: nomadik_nand: convert to mtd_device_register()
mtd: ndfc: convert to mtd_device_register()
mtd: mxc_nand: convert to mtd_device_register()
mtd: mpc5121_nfc: convert to mtd_device_register()
mtd: jz4740_nand: convert to mtd_device_register()
mtd: h1910: convert to mtd_device_register()
mtd: fsmc_nand: convert to mtd_device_register()
...
Fixed up trivial conflicts in
- drivers/mtd/maps/integrator-flash.c: removed in ARM tree
- drivers/mtd/maps/physmap.c: addition of afs partition probe type
clashing with removal of CONFIG_MTD_PARTITIONS
By the previous style change, CONFIG_GENERIC_FIND_NEXT_BIT,
CONFIG_GENERIC_FIND_BIT_LE, and CONFIG_GENERIC_FIND_LAST_BIT are not used
to test for existence of find bitops anymore.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Blackfin arch, like the x86 arch, needs to adjust the PC manually
after a breakpoint is hit as normally this is handled by the remote gdb.
However, rather than starting another arch ifdef mess, create a common
GDB_ADJUSTS_BREAK_OFFSET define for any arch to opt-in via their kgdb.h.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Dongdong Deng <dongdong.deng@windriver.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The functions probe_kernel_write() and probe_kernel_read() do not modify
the src pointer. Allow const pointers to be passed in without the need
of a typecast.
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/1305824936.1465.4.camel@gandalf.stny.rr.com
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: (37 commits)
Blackfin: use new common PERCPU_INPUT define
MAINTAINERS: Fix Analog Devices mailinglist address
Blackfin: boards: update ASoC resources after machine driver overhaul
Blackfin: work around anomaly 05000480
Blackfin: fix addr type with bfin_write_{or,and} helpers
Blackfin: convert /proc/sram to seq_file
Blackfin: switch /proc/gpio to seq_file
Blackfin: fix indentation with bfin_read() helper
Blackfin: convert old cpumask API to new one
Blackfin: don't touch task->cpus_allowed directly
Blackfin: don't touch cpu_possible_map and cpu_present_map directly
Blackfin: bf548-ezkit/bf561-ezkit: update nor flash layout
Blackfin: initial perf_event support
Blackfin: update anomaly lists to latest public info
Blackfin: use on-chip reset func with newer parts
Blackfin: bf533-stamp/bf537-stamp: drop ad1980 from defconfigs
Blackfin: optimize MMR reads during startup a bit
Blackfin: bf537: demux port H mask A and emac rx ints
Blackfin: bf537: fix excessive gpio int demuxing
Blackfin: bf54x: drop unused pm gpio handling
...
Most arches define CONFIG_DEBUG_STACK_USAGE exactly the same way. Move it
to lib/Kconfig.debug so each arch doesn't have to define it. This
obviously makes the option generic, but that's fine because the config is
already used in generic code.
It's not obvious to me that sysrq-P actually does anything caution by
keeping the most inclusive wording.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Richard Weinberger <richard@nod.at>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Blackfin percpu input sections are outdated, so rather than update
them, drop them completely and use the new common define.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Now that the Blackfin machine drivers have been updated to the
multicomponent support, update the resources to match. The pin
settings are now a board issue and removed from the driver.
Signed-off-by: Scott Jiang <scott.jiang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Anomaly 05000480 on BF537 rev 0.0, 0.1, 0.2:
Multiple Simultaneous Urgent DMA Requests May Cause DMA System Instability
Suggested Workaround:
Program the DMA Traffic Control Period to a non-zero value. This forces
the DMA block to group accesses together rather than allow arbitration for
each piece of data placed on the internal DMA bus.
Signed-off-by: Steven Miao <realmz6@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Since the bfin_write() func needs proper type information in order to
expand into the right bfin_writeX() variant, preserve the addr's type
when setting up the local __addr. Otherwise the helpers will detect
the variant based upon sizeof(void) which is almost never right.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
old cpu_xxx() APIs is planned to removed later. then, converted.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Every callter (except kthread_bind) should use proper
set_cpus_allowed_ptr() APIs.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We plan to remove cpu_possible_map and cpu_present_map later and we
have proper init_cpu_possible() and init_cpu_present() APIs.
Therefore this patch rewrites platform_init_cpus and platform_prepare_cpus
by their APIs.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Both the BF548-EZKIT and the BF561-EZKIT use top boot flashes, so now
that Das U-Boot uses the last small sector for its environment, update
their nor layout in the kernel accordingly.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Turns out the documentation is wrong and doing "RAISE 1" does not result
in a software reset, only a core reset. So when the on-chip rom has a
functioning reset helper, use it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
These boards don't have AD1980 modules, and that device is deprecated,
so don't bother building it up by default anymore.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Since the value of these MMRs aren't changing, store the value in a local
variable and work off of that. This avoids multiple MMR reads which are
implicitly forced by the volatile markings.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The BF537 SIC combines the gpio port H mask A interrupts with the
emac rx interrupt, so we need to demux this in software.
It also combines the gpio port H mask B and the emac tx interrupts,
and the watchdog and port F mask B interrupts, but since we don't
support mask B yet, just add the defines for now.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The search logic in the gpio demux walks all possible gpio blocks starting
at the specified pin. The trouble on bf537 parts when we demux the port
F and port G mask A interrupts is that we also demux port H mask A ints.
Most of the time this isn't an issue as people don't usually use port H,
but might as well avoid it when possible.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This functionality was merged into the common bfin_pm_standby_ctrl func
some time ago, so punt these now unused funcs and data, and localize the
wake funcs that aren't needed externally anymore.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The SIC interrupt line muxing that the bf537 does is specific to this
CPU (thankfully), so rip it out of the common code and move it to a
bf537-specific file. This tidies up the common code significantly.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
These are only used in a few internal Blackfin places, so move the irq
prototypes out of the global header and into the internal irq one. No
functional changes other than shuffling locales.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Prefer MMR named checks over part-specific lists, condense duplicated
code across different #ifdef branches, simplify CONFIG_PM ifdefs, and
drop unused kgdb header.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Make sure we mark cache flushing as unsafe to kgdb in SMP mode so that
kgdb doesn't flush things incorrectly on us.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
After some cache setup reordering changesets, the blackfin_cpudata init
was left behind. While cpu0's data was correct, cpu1's data was not.
Not that big of a deal as these are only used in the cpuinfo output, but
should still be fixed. So move the setup of these fields to the common
cache setup function to avoid this happening again in the future.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The smp flush lines are too long and have too many newlines, so scale
them back to match the other lines.
The %p modifier shows "(null)" for 0, so use %08x instead.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Build the sound pieces that the board actually has into the kernel, and
punt older devices that we discourage.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
These files had a lot of whitespace damage, mostly due to copying and
pasting original files that had damage.
The BF561 header also had a lot of unused CONFIG_DEF_xxx defines, so
punt them all.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Start a new common IRQ header and move all of the CEC pieces there. This
lets the individual part headers worry just about its SIC defines.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Seems the ipipe code just copied & pasted the existing irq lookup logic,
so pull the logic out of do_irq() and into a local helper, and convert
the two users over to that.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The local ivg structs need not be exported, so mark them as static.
Further, the "num_spurious" variable is only incremented and never
actually read anywhere, so punt it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Since the on-chip L1 regions are not cacheable, there is no point in
trying to flush/invalidate them. Plus, older Blackfin parts like to
trigger an exception (like BF533-0.3).
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Cc: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'for-2.6.40' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: Unify input section names
percpu: Avoid extra NOP in percpu_cmpxchg16b_double
percpu: Cast away printk format warning
percpu: Always align percpu output section to PAGE_SIZE
Fix up fairly trivial conflict in arch/x86/include/asm/percpu.h as per Tejun
* 'timers-clocksource-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
clocksource: convert mips to generic i8253 clocksource
clocksource: convert x86 to generic i8253 clocksource
clocksource: convert footbridge to generic i8253 clocksource
clocksource: add common i8253 PIT clocksource
blackfin: convert to clocksource_register_hz
mips: convert to clocksource_register_hz/khz
sparc: convert to clocksource_register_hz/khz
alpha: convert to clocksource_register_hz
microblaze: convert to clocksource_register_hz/khz
ia64: convert to clocksource_register_hz/khz
x86: Convert remaining x86 clocksources to clocksource_register_hz/khz
Make clocksource name const
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (60 commits)
sched: Fix and optimise calculation of the weight-inverse
sched: Avoid going ahead if ->cpus_allowed is not changed
sched, rt: Update rq clock when unthrottling of an otherwise idle CPU
sched: Remove unused parameters from sched_fork() and wake_up_new_task()
sched: Shorten the construction of the span cpu mask of sched domain
sched: Wrap the 'cfs_rq->nr_spread_over' field with CONFIG_SCHED_DEBUG
sched: Remove unused 'this_best_prio arg' from balance_tasks()
sched: Remove noop in alloc_rt_sched_group()
sched: Get rid of lock_depth
sched: Remove obsolete comment from scheduler_tick()
sched: Fix sched_domain iterations vs. RCU
sched: Next buddy hint on sleep and preempt path
sched: Make set_*_buddy() work on non-task entities
sched: Remove need_migrate_task()
sched: Move the second half of ttwu() to the remote cpu
sched: Restructure ttwu() some more
sched: Rename ttwu_post_activation() to ttwu_do_wakeup()
sched: Remove rq argument from ttwu_stat()
sched: Remove rq->lock from the first half of ttwu()
sched: Drop rq->lock from sched_exec()
...
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Fix rt_rq runtime leakage bug
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6: (34 commits)
PM: Introduce generic prepare and complete callbacks for subsystems
PM: Allow drivers to allocate memory from .prepare() callbacks safely
PM: Remove CONFIG_PM_VERBOSE
Revert "PM / Hibernate: Reduce autotuned default image size"
PM / Hibernate: Add sysfs knob to control size of memory for drivers
PM / Wakeup: Remove useless synchronize_rcu() call
kmod: always provide usermodehelper_disable()
PM / ACPI: Remove acpi_sleep=s4_nonvs
PM / Wakeup: Fix build warning related to the "wakeup" sysfs file
PM: Print a warning if firmware is requested when tasks are frozen
PM / Runtime: Rework runtime PM handling during driver removal
Freezer: Use SMP barriers
PM / Suspend: Do not ignore error codes returned by suspend_enter()
PM: Fix build issue in clock_ops.c for CONFIG_PM_RUNTIME unset
PM: Revert "driver core: platform_bus: allow runtime override of dev_pm_ops"
OMAP1 / PM: Use generic clock manipulation routines for runtime PM
PM: Remove sysdev suspend, resume and shutdown operations
PM / PowerPC: Use struct syscore_ops instead of sysdevs for PM
PM / UNICORE32: Use struct syscore_ops instead of sysdevs for PM
PM / AVR32: Use struct syscore_ops instead of sysdevs for PM
...
Conflicts:
arch/ia64/kernel/cyclone.c
arch/mips/kernel/i8253.c
arch/x86/kernel/i8253.c
Reason: Resolve conflicts so further cleanups do not conflict further
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
With dynamic debug having gained the capability to report debug messages
also during the boot process, it offers a far superior interface for
debug messages than the custom cpufreq infrastructure. As a first step,
remove the old cpufreq_debug_printk() function and replace it with a call
to the generic pr_debug() function.
How can dynamic debug be used on cpufreq? You need a kernel which has
CONFIG_DYNAMIC_DEBUG enabled.
To enabled debugging during runtime, mount debugfs and
$ echo -n 'module cpufreq +p' > /sys/kernel/debug/dynamic_debug/control
for debugging the complete "cpufreq" module. To achieve the same goal during
boot, append
ddebug_query="module cpufreq +p"
as a boot parameter to the kernel of your choice.
For more detailled instructions, please see
Documentation/dynamic-debug-howto.txt
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
Convert some Blackfin architecture's code to using struct syscore_ops
objects for power management instead of sysdev classes and sysdevs.
This simplifies the code and reduces the kernel's memory footprint.
It also is necessary for removing sysdevs from the kernel entirely in
the future.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
For future rework of try_to_wake_up() we'd like to push part of that
function onto the CPU the task is actually going to run on.
In order to do so we need a generic callback from the existing scheduler IPI.
This patch introduces such a generic callback: scheduler_ipi() and
implements it as a NOP.
BenH notes: PowerPC might use this IPI on offline CPUs under rare conditions!
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reviewed-by: Frank Rowand <frank.rowand@am.sony.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20110405152728.744338123@chello.nl
The recent commit (10774912647781) wasn't entirely correct. While
it fixed some issues, it introduced others. So pull in the fixes
from the public cache flush functions, and document why we need to
call things directly ourselves.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
If the period of a gptimer is fairly low, we might miss an interrupt
by acking it too late (we end up acking the new int as well).
Reported-by: Isabelle Leonardi <i.leonardi@detracom.fr>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We only want to clear the run bit for this one timer, not all status bits.
So don't read the whole reg and then write all the bits back out.
Reported-by: Isabelle Leonardi <i.leonardi@detracom.fr>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When suspending/resuming, the common task freezing code will run in
parallel and freeze processes on each core. This is because the code
uses the non-smp version of memory barriers (as well it should).
The Blackfin smp barrier logic at the moment contains the cache sync
logic, but the non-smp barriers do not. This is incorrect as Rafel
summarized:
> ...
> The existing memory barriers are SMP barriers too, but they are more
> than _just_ SMP barriers. At least that's how it is _supposed_ to be
> (eg. rmb() is supposed to be stronger than smp_rmb()).
> ...
> However, looking at the blackfin's definitions of SMP barriers I see
> that it uses extra stuff that should _also_ be used in the definitions
> of the mandatory barriers.
> ...
URL: http://lkml.org/lkml/2011/4/13/11
LKML-Reference: <BANLkTi=F-C-vwX4PGGfbkdTBw3OWL-twfg@mail.gmail.com>
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
avr32: Fix missing irq namespace conversion
powerpc: qe_ic: Rename get_irq_desc_data and get_irq_desc_chip
genirq: Remove the now obsolete config options and select statements
arm: versatile : Fix typo introduced in irq namespace cleanup
sound: Fixup the last user of the old irq functions
genirq: Remove obsolete comment
genirq: Remove now obsolete set_irq_wake()
sh: Fix irq cleanup fallout
x86: apb_timer: Fixup genirq fallout
genirq: Fix misnamed label in handle_edge_eoi_irq
Fix up crazy conflict in arch/powerpc/include/asm/qe_ic.h:
- commit eead4d5c63 ("powerpc: qe_ic: Rename get_irq_desc_data and
get_irq_desc_chip") made the helper functions use
irq_desc_get_handler_data() instead of the legacy (and no longer
existing) get_irq_desc_data.
- commit d4db35e8dc ("powerpc/qe_ic: Fix another breakage from the
irq_data conversion") used irq_desc_get_chip_data() instead.
According to Thomas, the former is the correct direct conversion, but it
does look like both should work (arch/powerpc/sysdev/qe_lib/qe_ic.c
seems to initialize both to the same thing), and the chip data in some
ways is the more logical. Somebody should really decide on one of the
other.
This merge picks irq_desc_get_handler_data() as the straightforward pure
conversion to new names, as per Thomas.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin:
Blackfin: bitops: fix include order after little endian inclusion
Blackfin: defconfigs: update after misc devices defaulted to N
Blackfin: use more standard pr_fmt in the module loader
Convert to the new function names. Scripted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: uclinux-dist-devel@blackfin.uclinux.org
Use the trigger type in irq_data and check level type instead of
looking at desc->handle_irq.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: uclinux-dist-devel@blackfin.uclinux.org
The le.h header requires things like test_bit to be declared, so we need
to move its inclusion to after the point where that happens.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The default value for misc devices was changed from Y to N which
causes problems for mini defconfigs that were relying on this
defaulting to Y. So update all of the defconfigs accordingly.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Changed pr_fmt(fmt) to make the format arguments match the format.
Changed an argument name in apply_relocate from me to mod so that
the pr_err is consistent with the other uses.
Added missing '\n' to a format.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Percpu allocator honors alignment request upto PAGE_SIZE and both the
percpu addresses in the percpu address space and the translated kernel
addresses should be aligned accordingly. The calculation of the
former depends on the alignment of percpu output section in the kernel
image.
The linker script macros PERCPU_VADDR() and PERCPU() are used to
define this output section and the latter takes @align parameter.
Several architectures are using @align smaller than PAGE_SIZE breaking
percpu memory alignment.
This patch removes @align parameter from PERCPU(), renames it to
PERCPU_SECTION() and makes it always align to PAGE_SIZE. While at it,
add PCPU_SETUP_BUG_ON() checks such that alignment problems are
reliably detected and remove percpu alignment comment recently added
in workqueue.c as the condition would trigger BUG way before reaching
there.
For um, this patch raises the alignment of percpu area. As the area
is in .init, there shouldn't be any noticeable difference.
This problem was discovered by David Howells while debugging boot
failure on mn10300.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Cc: uclinux-dist-devel@blackfin.uclinux.org
Cc: David Howells <dhowells@redhat.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: user-mode-linux-devel@lists.sourceforge.net
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin:
Blackfin: bf54x: re-enable anomaly 05000353 for all revs
Blackfin: enable atomic64_t support
Blackfin: wire up new syncfs syscall
Blackfin: SMP: flush CoreB cache when shutting down
minix bit operations are only used by minix filesystem and useless by
other modules. Because byte order of inode and block bitmaps is different
on each architecture like below:
m68k:
big-endian 16bit indexed bitmaps
h8300, microblaze, s390, sparc, m68knommu:
big-endian 32 or 64bit indexed bitmaps
m32r, mips, sh, xtensa:
big-endian 32 or 64bit indexed bitmaps for big-endian mode
little-endian bitmaps for little-endian mode
Others:
little-endian bitmaps
In order to move minix bit operations from asm/bitops.h to architecture
independent code in minix filesystem, this provides two config options.
CONFIG_MINIX_FS_BIG_ENDIAN_16BIT_INDEXED is only selected by m68k.
CONFIG_MINIX_FS_NATIVE_ENDIAN is selected by the architectures which use
native byte order bitmaps (h8300, microblaze, s390, sparc, m68knommu,
m32r, mips, sh, xtensa). The architectures which always use little-endian
bitmaps do not select these options.
Finally, we can remove minix bit operations from asm/bitops.h for all
architectures.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Michal Simek <monstr@monstr.eu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As the result of conversions, there are no users of ext2 non-atomic bit
operations except for ext2 filesystem itself. Now we can put them into
architecture independent code in ext2 filesystem, and remove from
asm/bitops.h for all architectures.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce little-endian bit operations to the big-endian architectures
which do not have native little-endian bit operations and the
little-endian architectures. (alpha, avr32, blackfin, cris, frv, h8300,
ia64, m32r, mips, mn10300, parisc, sh, sparc, tile, x86, xtensa)
These architectures can just include generic implementation
(asm-generic/bitops/le.h).
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Zankel <chris@zankel.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Even though the anomaly sheet says that the the bootrom is fixed, tests
have shown that the fix itself does not handle all cases. So until we
get a ROM update, assume the reset code is still broken and we need to
handle things ourselves.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger