When IO is successfully completed while an abort is pending, eh_abort
incorrectly assumes that abort failed and performes recovery by issuing
cleanup. Howerver, cleanup timesout as the firmware has no clue about
this IO. Fix this by checking if the IO has already completed.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Set perf_config to 3 during firmware initialization to enable both
cached connections as well as cached tasks.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If switch configured in FIP and adapter configured in non-fip mode, driver
panics while queueing FIP frame in non-existing fip_frame_queue. Added config
check before queueing FIP frame in misconfiguration case to avoid kernel panic.
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
FIP VLAN discovery discovers the FCoE VLAN that will be used by all other FIP
protocols as well as by the FCoE encapsulation for Fibre Channel payloads on
the established virtual link. One of the goals of FC-BB-5 was to be as
nonintrusive as possible on initiators and targets, and therefore FIP VLAN
discovery occurs in the native VLAN used by the initiator or target to
exchange Ethernet traffic. The FIP VLAN discovery protocol is the only FIP
protocol running on the native VLAN; all other FIP protocols run on the
discovered FCoE VLANs.
If an administrator has manually configured FCoE VLANs on ENodes and FCFs,
there is no need to use this protocol. FIP and FCoE will run over the
configured VLANs.
An ENode without FCoE VLANs configuration would use this automated discovery
protocol to discover over which VLANs FCoE is running.
The ENode sends a FIP VLAN discovery request to a multicast MAC address called
All-FCF-MACs, which is a multicast MAC address to which all FCFs listen.
All FCFs that can be reached in the native VLAN of the ENode are expected to
respond on the same VLAN with a response that lists one or more FCoE VLANs
that are available for the ENode's VN_Port login. This protocol has the sole
purpose of allowing the ENode to discover all the available FCoE VLANs.
Now the ENode may enable a subset of these VLANs for FCoE Running the FIP
protocol in these VLANs on a per VLAN basis. And FCoE data transactions also
would occur on this VLAN. Hence, Except for FIP VLAN discovery, all other FIP
and FCoE traffic runs on the selected FCoE VLAN. Its only the FIP VLAN
Discovery protocol that is permitted to run on the Default native VLAN of the
system.
[**** NOTE ****]
We are working on moving this feature definitions and functionality to libfcoe
module. We need this patch to be approved, as Suse is looking forward to merge
this feature in SLES 11 SP3 release. Once this patch is approved, we will
submit patch which should move vlan discovery feature to libfoce.
[Fengguang Wu <fengguang.wu@intel.com>: kmalloc cast removal]
Signed-off-by: Anantha Prakash T <atungara@cisco.com>
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Pull networking updates from David Miller:
"Highlights (1721 non-merge commits, this has to be a record of some
sort):
1) Add 'random' mode to team driver, from Jiri Pirko and Eric
Dumazet.
2) Make it so that any driver that supports configuration of multiple
MAC addresses can provide the forwarding database add and del
calls by providing a default implementation and hooking that up if
the driver doesn't have an explicit set of handlers. From Vlad
Yasevich.
3) Support GSO segmentation over tunnels and other encapsulating
devices such as VXLAN, from Pravin B Shelar.
4) Support L2 GRE tunnels in the flow dissector, from Michael Dalton.
5) Implement Tail Loss Probe (TLP) detection in TCP, from Nandita
Dukkipati.
6) In the PHY layer, allow supporting wake-on-lan in situations where
the PHY registers have to be written for it to be configured.
Use it to support wake-on-lan in mv643xx_eth.
From Michael Stapelberg.
7) Significantly improve firewire IPV6 support, from YOSHIFUJI
Hideaki.
8) Allow multiple packets to be sent in a single transmission using
network coding in batman-adv, from Martin Hundebøll.
9) Add support for T5 cxgb4 chips, from Santosh Rastapur.
10) Generalize the VXLAN forwarding tables so that there is more
flexibility in configurating various aspects of the endpoints.
From David Stevens.
11) Support RSS and TSO in hardware over GRE tunnels in bxn2x driver,
from Dmitry Kravkov.
12) Zero copy support in nfnelink_queue, from Eric Dumazet and Pablo
Neira Ayuso.
13) Start adding networking selftests.
14) In situations of overload on the same AF_PACKET fanout socket, or
per-cpu packet receive queue, minimize drop by distributing the
load to other cpus/fanouts. From Willem de Bruijn and Eric
Dumazet.
15) Add support for new payload offset BPF instruction, from Daniel
Borkmann.
16) Convert several drivers over to mdoule_platform_driver(), from
Sachin Kamat.
17) Provide a minimal BPF JIT image disassembler userspace tool, from
Daniel Borkmann.
18) Rewrite F-RTO implementation in TCP to match the final
specification of it in RFC4138 and RFC5682. From Yuchung Cheng.
19) Provide netlink socket diag of netlink sockets ("Yo dawg, I hear
you like netlink, so I implemented netlink dumping of netlink
sockets.") From Andrey Vagin.
20) Remove ugly passing of rtnetlink attributes into rtnl_doit
functions, from Thomas Graf.
21) Allow userspace to be able to see if a configuration change occurs
in the middle of an address or device list dump, from Nicolas
Dichtel.
22) Support RFC3168 ECN protection for ipv6 fragments, from Hannes
Frederic Sowa.
23) Increase accuracy of packet length used by packet scheduler, from
Jason Wang.
24) Beginning set of changes to make ipv4/ipv6 fragment handling more
scalable and less susceptible to overload and locking contention,
from Jesper Dangaard Brouer.
25) Get rid of using non-type-safe NLMSG_* macros and use nlmsg_*()
instead. From Hong Zhiguo.
26) Optimize route usage in IPVS by avoiding reference counting where
possible, from Julian Anastasov.
27) Convert IPVS schedulers to RCU, also from Julian Anastasov.
28) Support cpu fanouts in xt_NFQUEUE netfilter target, from Holger
Eitzenberger.
29) Network namespace support for nf_log, ebt_log, xt_LOG, ipt_ULOG,
nfnetlink_log, and nfnetlink_queue. From Gao feng.
30) Implement RFC3168 ECN protection, from Hannes Frederic Sowa.
31) Support several new r8169 chips, from Hayes Wang.
32) Support tokenized interface identifiers in ipv6, from Daniel
Borkmann.
33) Use usbnet_link_change() helper in USB net driver, from Ming Lei.
34) Add 802.1ad vlan offload support, from Patrick McHardy.
35) Support mmap() based netlink communication, also from Patrick
McHardy.
36) Support HW timestamping in mlx4 driver, from Amir Vadai.
37) Rationalize AF_PACKET packet timestamping when transmitting, from
Willem de Bruijn and Daniel Borkmann.
38) Bring parity to what's provided by /proc/net/packet socket dumping
and the info provided by netlink socket dumping of AF_PACKET
sockets. From Nicolas Dichtel.
39) Fix peeking beyond zero sized SKBs in AF_UNIX, from Benjamin
Poirier"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
filter: fix va_list build error
af_unix: fix a fatal race with bit fields
bnx2x: Prevent memory leak when cnic is absent
bnx2x: correct reading of speed capabilities
net: sctp: attribute printl with __printf for gcc fmt checks
netlink: kconfig: move mmap i/o into netlink kconfig
netpoll: convert mutex into a semaphore
netlink: Fix skb ref counting.
net_sched: act_ipt forward compat with xtables
mlx4_en: fix a build error on 32bit arches
Revert "bnx2x: allow nvram test to run when device is down"
bridge: avoid OOPS if root port not found
drivers: net: cpsw: fix kernel warn on cpsw irq enable
sh_eth: use random MAC address if no valid one supplied
3c509.c: call SET_NETDEV_DEV for all device types (ISA/ISAPnP/EISA)
tg3: fix to append hardware time stamping flags
unix/stream: fix peeking with an offset larger than data in queue
unix/dgram: fix peeking with an offset larger than data in queue
unix/dgram: peek beyond 0-sized skbs
openvswitch: Remove unneeded ovs_netdev_get_ifindex()
...
This patch fixes the following build error.
In file included from include/linux/filter.h:52:0,
from arch/arm/net/bpf_jit_32.c:14:
include/linux/printk.h:54:2: error: unknown type name ‘va_list’
include/linux/printk.h:105:21: error: unknown type name ‘va_list’
include/linux/printk.h:108:30: error: unknown type name ‘va_list’
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull input updates from Dmitry Torokhov:
"Assorted fixes and cleanups to the existing drivers plus a new driver
for IMS Passenger Control Unit device they use for ther in-flight
entertainment system."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (44 commits)
Input: trackpoint - Optimize trackpoint init to use power-on reset
Input: apbps2 - convert to devm_ioremap_resource()
Input: ALPS - use %ph to print buffers
ARM - shmobile: Armadillo800EVA: Move st1232 reset pin handling
Input: st1232 - add reset pin handling
Input: st1232 - convert to devm_* infrastructure
Input: MT - handle semi-mt devices in core
Input: adxl34x - use spi_get_drvdata()
Input: ad7877 - use spi_get_drvdata() and spi_set_drvdata()
Input: ads7846 - use spi_get_drvdata() and spi_set_drvdata()
Input: ims-pcu - fix a memory leak on error
Input: sysrq - supplement reset sequence with timeout functionality
Input: tegra-kbc - support for defining row/columns based on SoC
Input: imx_keypad - switch to using managed resources
Input: arc_ps2 - add support for device tree
Input: mma8450 - fix signed 12bits to 32bits conversion
Input: eeti_ts - remove redundant null check
Input: edt-ft5x06 - remove redundant null check before kfree
Input: ad714x - add CONFIG_PM_SLEEP to suspend/resume functions
Input: adxl34x - add CONFIG_PM_SLEEP to suspend/resume functions
...
Using bit fields is dangerous on ppc64/sparc64, as the compiler [1]
uses 64bit instructions to manipulate them.
If the 64bit word includes any atomic_t or spinlock_t, we can lose
critical concurrent changes.
This is happening in af_unix, where unix_sk(sk)->gc_candidate/
gc_maybe_cycle/lock share the same 64bit word.
This leads to fatal deadlock, as one/several cpus spin forever
on a spinlock that will never be available again.
A safer way would be to use a long to store flags.
This way we are sure compiler/arch wont do bad things.
As we own unix_gc_lock spinlock when clearing or setting bits,
we can use the non atomic __set_bit()/__clear_bit().
recursion_level can share the same 64bit location with the spinlock,
as it is set only with this spinlock held.
[1] bug fixed in gcc-4.8.0 :
http://gcc.gnu.org/bugzilla/show_bug.cgi?id=52080
Reported-by: Ambrose Feinstein <ambrose@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz says:
====================
This fixes 2 small bugs - one which may cause an unnecessary link flap,
and the other is a small memory leak when unloading while cnic is not
loaded.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x driver allocates searcher T2 tables, but it releases that memory
during unload only released if the cnic is loaded.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the bnx2x driver reads the port configuration - mask irrelevant bits.
Without this change, the unintended bits may cause the driver to needlessly
toggle the link, as a comparison in the link flap avoidance flow will show
that the old link did not advertise the same capabilities and thus cannot
be retained.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let GCC check for format string errors in sctp's probe printl
function. This patch fixes the warning when compiled with W=1:
net/sctp/probe.c:73:2: warning: function might be possible candidate
for 'gnu_printf' format attribute [-Wmissing-format-attribute]
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, in menuconfig, Netlink's new mmaped IO is the very first
entry under the ``Networking support'' item and comes even before
``Networking options'':
[ ] Netlink: mmaped IO
Networking options --->
...
Lets move this into ``Networking options'' under netlink's Kconfig,
since this might be more appropriate. Introduced by commit ccdfcc398
(``netlink: mmaped netlink: ring setup'').
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bart Van Assche recently reported a warning to me:
<IRQ> [<ffffffff8103d79f>] warn_slowpath_common+0x7f/0xc0
[<ffffffff8103d7fa>] warn_slowpath_null+0x1a/0x20
[<ffffffff814761dd>] mutex_trylock+0x16d/0x180
[<ffffffff813968c9>] netpoll_poll_dev+0x49/0xc30
[<ffffffff8136a2d2>] ? __alloc_skb+0x82/0x2a0
[<ffffffff81397715>] netpoll_send_skb_on_dev+0x265/0x410
[<ffffffff81397c5a>] netpoll_send_udp+0x28a/0x3a0
[<ffffffffa0541843>] ? write_msg+0x53/0x110 [netconsole]
[<ffffffffa05418bf>] write_msg+0xcf/0x110 [netconsole]
[<ffffffff8103eba1>] call_console_drivers.constprop.17+0xa1/0x1c0
[<ffffffff8103fb76>] console_unlock+0x2d6/0x450
[<ffffffff8104011e>] vprintk_emit+0x1ee/0x510
[<ffffffff8146f9f6>] printk+0x4d/0x4f
[<ffffffffa0004f1d>] scsi_print_command+0x7d/0xe0 [scsi_mod]
This resulted from my commit ca99ca14c which introduced a mutex_trylock
operation in a path that could execute in interrupt context. When mutex
debugging is enabled, the above warns the user when we are in fact
exectuting in interrupt context
interrupt context.
After some discussion, It seems that a semaphore is the proper mechanism to use
here. While mutexes are defined to be unusable in interrupt context, no such
condition exists for semaphores (save for the fact that the non blocking api
calls, like up and down_trylock must be used when in irq context).
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Bart Van Assche <bvanassche@acm.org>
CC: Bart Van Assche <bvanassche@acm.org>
CC: David Miller <davem@davemloft.net>
CC: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f9c2288837 (netlink:
implement memory mapped recvmsg) increamented skb->users
ref count twice for a dump op which does not look right.
Following patch fixes that.
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull tile arch changes from Chris Metcalf:
"These are some minor new feature work and other changes that didn't
merit getting pushed up after the 3.9 merge window closed.
There should be a lot more activity in the 3.11 merge window"
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile: Fix syscall return value passed to tracepoint
tile: comment assumption about __insn_mtspr for <asm/irqflags.h>
tile: ns2cycles should use __raw_get_cpu_var
arch: remove KCORE_ELF again [tile]
tile: remove two outdated Kconfig entries
tile: support atomic64_dec_if_positive()
tile: support TIF_SYSCALL_TRACEPOINT; select HAVE_SYSCALL_TRACEPOINTS
tile: Add definition of NR_syscalls
tile: move declaration of sys_call_table to <asm/syscall.h>
arch/tile: Enable HAVE_ARCH_TRACEHOOK
arch/tile: Call tracehook_report_syscall_{entry,exit} in syscall trace
Commit f91eb62f71 ("init: scream bloody murder if interrupts are
enabled too early") added three new warnings. The first two seemed
reasonable, but the third included a warning when an initcall returned
non-zero. Although, the third WARN() does include an imbalanced preempt
disabled, or irqs disable, it shouldn't warn if it only had an initcall
that just returns non-zero.
In fact, according to Linus, it shouldn't print at all. As it only
prints with initcall_debug set, and that already shows enough
information to fix things.
Link: http://lkml.kernel.org/r/CA+55aFzaBC5SFi7=F2mfm+KWY5qTsBmOqgbbs8E+LUS8JK-sBg@mail.gmail.com
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Deal with changes in newer xtables while maintaining backward
compatibility. Thanks to Jan Engelhardt for suggestions.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull omap3isp clk support from Mauro Carvalho Chehab:
"This patch were sent in separate as it depends on a merge from clock
framework, that you merged in commit 362ed48dee50"
* 'topic/omap3isp' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] omap3isp: Use the common clock framework
Merge IPC cleanup and scalability patches from Andrew Morton.
This cleans up many of the oddities in the IPC code, uses the list
iterator helpers, splits out locking and adds per-semaphore locks for
greater scalability of the IPC semaphore code.
Most normal user-level locking by now uses futexes (ie pthreads, but
also a lot of specialized locks), but SysV IPC semaphores are apparently
still used in some big applications, either for portability reasons, or
because they offer tracking and undo (and you don't need to have a
special shared memory area for them).
Our IPC semaphore scalability was pitiful. We used to lock much too big
ranges, and we used to have a single ipc lock per ipc semaphore array.
Most loads never cared, but some do. There are some numbers in the
individual commits.
* ipc-scalability:
ipc: sysv shared memory limited to 8TiB
ipc/msg.c: use list_for_each_entry_[safe] for list traversing
ipc,sem: fine grained locking for semtimedop
ipc,sem: have only one list in struct sem_queue
ipc,sem: open code and rename sem_lock
ipc,sem: do not hold ipc lock more than necessary
ipc: introduce lockless pre_down ipcctl
ipc: introduce obtaining a lockless ipc object
ipc: remove bogus lock comment for ipc_checkid
ipc/msgutil.c: use linux/uaccess.h
ipc: refactor msg list search into separate function
ipc: simplify msg list search
ipc: implement MSG_COPY as a new receive mode
ipc: remove msg handling from queue scan
ipc: set EFAULT as default error in load_msg()
ipc: tighten msg copy loops
ipc: separate msg allocation from userspace copy
ipc: clamp with min()
Trying to run an application which was trying to put data into half of
memory using shmget(), we found that having a shmall value below 8EiB-8TiB
would prevent us from using anything more than 8TiB. By setting
kernel.shmall greater than 8EiB-8TiB would make the job work.
In the newseg() function, ns->shm_tot which, at 8TiB is INT_MAX.
ipc/shm.c:
458 static int newseg(struct ipc_namespace *ns, struct ipc_params *params)
459 {
...
465 int numpages = (size + PAGE_SIZE -1) >> PAGE_SHIFT;
...
474 if (ns->shm_tot + numpages > ns->shm_ctlall)
475 return -ENOSPC;
[akpm@linux-foundation.org: make ipc/shm.c:newseg()'s numpages size_t, not int]
Signed-off-by: Robin Holt <holt@sgi.com>
Reported-by: Alex Thorlton <athorlton@sgi.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ipc/msg.c code does its list operations by hand and it open-codes the
accesses, instead of using for_each_entry_[safe].
Signed-off-by: Nikola Pajkovsky <npajkovs@redhat.com>
Cc: Stanislav Kinsbursky <skinsbursky@parallels.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce finer grained locking for semtimedop, to handle the common case
of a program wanting to manipulate one semaphore from an array with
multiple semaphores.
If the call is a semop manipulating just one semaphore in an array with
multiple semaphores, only take the lock for that semaphore itself.
If the call needs to manipulate multiple semaphores, or another caller is
in a transaction that manipulates multiple semaphores, the sem_array lock
is taken, as well as all the locks for the individual semaphores.
On a 24 CPU system, performance numbers with the semop-multi
test with N threads and N semaphores, look like this:
vanilla Davidlohr's Davidlohr's + Davidlohr's +
threads patches rwlock patches v3 patches
10 610652 726325 1783589 2142206
20 341570 365699 1520453 1977878
30 288102 307037 1498167 2037995
40 290714 305955 1612665 2256484
50 288620 312890 1733453 2650292
60 289987 306043 1649360 2388008
70 291298 306347 1723167 2717486
80 290948 305662 1729545 2763582
90 290996 306680 1736021 2757524
100 292243 306700 1773700 3059159
[davidlohr.bueso@hp.com: do not call sem_lock when bogus sma]
[davidlohr.bueso@hp.com: make refcounter atomic]
Signed-off-by: Rik van Riel <riel@redhat.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Chegu Vinod <chegu_vinod@hp.com>
Cc: Jason Low <jason.low2@hp.com>
Reviewed-by: Michel Lespinasse <walken@google.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Stanislav Kinsbursky <skinsbursky@parallels.com>
Tested-by: Emmanuel Benisty <benisty.e@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Having only one list in struct sem_queue, and only queueing simple
semaphore operations on the list for the semaphore involved, allows us to
introduce finer grained locking for semtimedop.
Signed-off-by: Rik van Riel <riel@redhat.com>
Acked-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Chegu Vinod <chegu_vinod@hp.com>
Cc: Emmanuel Benisty <benisty.e@gmail.com>
Cc: Jason Low <jason.low2@hp.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Stanislav Kinsbursky <skinsbursky@parallels.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename sem_lock() to sem_obtain_lock(), so we can introduce a sem_lock()
later that only locks the sem_array and does nothing else.
Open code the locking from ipc_lock() in sem_obtain_lock() so we can
introduce finer grained locking for the sem_array in the next patch.
[akpm@linux-foundation.org: propagate the ipc_obtain_object() errno out of sem_obtain_lock()]
Signed-off-by: Rik van Riel <riel@redhat.com>
Acked-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Chegu Vinod <chegu_vinod@hp.com>
Cc: Emmanuel Benisty <benisty.e@gmail.com>
Cc: Jason Low <jason.low2@hp.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Stanislav Kinsbursky <skinsbursky@parallels.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Various forms of ipc use ipcctl_pre_down() to retrieve an ipc object and
check permissions, mostly for IPC_RMID and IPC_SET commands.
Introduce ipcctl_pre_down_nolock(), a lockless version of this function.
The locking version is retained, yet modified to call the nolock version
without affecting its semantics, thus transparent to all ipc callers.
Signed-off-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Signed-off-by: Rik van Riel <riel@redhat.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Chegu Vinod <chegu_vinod@hp.com>
Cc: Emmanuel Benisty <benisty.e@gmail.com>
Cc: Jason Low <jason.low2@hp.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Stanislav Kinsbursky <skinsbursky@parallels.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Through ipc_lock() and therefore ipc_lock_check() we currently return the
locked ipc object. This is not necessary for all situations and can,
therefore, cause unnecessary ipc lock contention.
Introduce analogous ipc_obtain_object() and ipc_obtain_object_check()
functions that only lookup and return the ipc object.
Both these functions must be called within the RCU read critical section.
[akpm@linux-foundation.org: propagate the ipc_obtain_object() errno from ipc_lock()]
Signed-off-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Signed-off-by: Rik van Riel <riel@redhat.com>
Reviewed-by: Chegu Vinod <chegu_vinod@hp.com>
Acked-by: Michel Lespinasse <walken@google.com>
Cc: Emmanuel Benisty <benisty.e@gmail.com>
Cc: Jason Low <jason.low2@hp.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Stanislav Kinsbursky <skinsbursky@parallels.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This series makes the sysv semaphore code more scalable, by reducing the
time the semaphore lock is held, and making the locking more scalable for
semaphore arrays with multiple semaphores.
The first four patches were written by Davidlohr Buesso, and reduce the
hold time of the semaphore lock.
The last three patches change the sysv semaphore code locking to be more
fine grained, providing a performance boost when multiple semaphores in a
semaphore array are being manipulated simultaneously.
On a 24 CPU system, performance numbers with the semop-multi
test with N threads and N semaphores, look like this:
vanilla Davidlohr's Davidlohr's + Davidlohr's +
threads patches rwlock patches v3 patches
10 610652 726325 1783589 2142206
20 341570 365699 1520453 1977878
30 288102 307037 1498167 2037995
40 290714 305955 1612665 2256484
50 288620 312890 1733453 2650292
60 289987 306043 1649360 2388008
70 291298 306347 1723167 2717486
80 290948 305662 1729545 2763582
90 290996 306680 1736021 2757524
100 292243 306700 1773700 3059159
This patch:
There is no reason to be holding the ipc lock while reading ipcp->seq,
hence remove misleading comment.
Also simplify the return value for the function.
Signed-off-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: Chegu Vinod <chegu_vinod@hp.com>
Cc: Emmanuel Benisty <benisty.e@gmail.com>
Cc: Jason Low <jason.low2@hp.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Stanislav Kinsbursky <skinsbursky@parallels.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Teach the helper routines about MSG_COPY so that msgtyp is preserved as
the message number to copy.
The security functions affected by this change were audited and no
additional changes are necessary.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In preparation for refactoring the queue scan into a separate
function, relocate msg copying.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
feature this merge window is a new ioctl EXT4_IOC_SWAP_BOOT which
allows installation of a hidden inode designed for boot loaders.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=GCT2
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 updates from Ted Ts'o:
"Mostly performance and bug fixes, plus some cleanups. The one new
feature this merge window is a new ioctl EXT4_IOC_SWAP_BOOT which
allows installation of a hidden inode designed for boot loaders."
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (50 commits)
ext4: fix type-widening bug in inode table readahead code
ext4: add check for inodes_count overflow in new resize ioctl
ext4: fix Kconfig documentation for CONFIG_EXT4_DEBUG
ext4: fix online resizing for ext3-compat file systems
jbd2: trace when lock_buffer in do_get_write_access takes a long time
ext4: mark metadata blocks using bh flags
buffer: add BH_Prio and BH_Meta flags
ext4: mark all metadata I/O with REQ_META
ext4: fix readdir error in case inline_data+^dir_index.
ext4: fix readdir error in the case of inline_data+dir_index
jbd2: use kmem_cache_zalloc instead of kmem_cache_alloc/memset
ext4: mext_insert_extents should update extent block checksum
ext4: move quota initialization out of inode allocation transaction
ext4: reserve xattr index for Rich ACL support
jbd2: reduce journal_head size
ext4: clear buffer_uninit flag when submitting IO
ext4: use io_end for multiple bios
ext4: make ext4_bio_write_page() use BH_Async_Write flags
ext4: Use kstrtoul() instead of parse_strtoul()
ext4: defragmentation code cleanup
...
Pull Hexagon fixes from Richard Kuo:
"Changes for the Hexagon architecture (and one touching OpenRISC).
They include various fixes to make use of additional arch features and
cleanups. The largest functional change is a cleanup of the signal
and event return paths"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rkuo/linux-hexagon-kernel: (32 commits)
Hexagon: add v4 CS regs to core copyout macro
Hexagon: use correct translation for VMALLOC_START
Hexagon: use correct translations for DMA mappings
Hexagon: fix return value for notify_resume case in do_work_pending
Hexagon: fix signal number for user mem faults
Hexagon: remove two Kconfig entries
arch: remove CONFIG_GENERIC_FIND_NEXT_BIT again
Hexagon: update copyright dates
Hexagon: add translation types for __vmnewmap
Hexagon: fix signal.c compile error
Hexagon: break up user fn/arg register setting
Hexagon: use generic sys_fork, sys_vfork, and sys_clone
Hexagon: fix psp/sp macro
Hexagon: fix up int enable/disable at ret_from_fork
Hexagon: add IOMEM and _relaxed IO macros
Hexagon: switch to using the device type for IO mappings
Hexagon: don't print info for offline CPU's
Hexagon: add support for single-stepping (v4+)
Hexagon: use correct work mask when checking for more work
Hexagon: add support for additional exceptions
...
We first tried to avoid updating atime/mtime entirely (commit
b0de59b5733d: "TTY: do not update atime/mtime on read/write"), and then
limited it to only update it occasionally (commit 37b7f3c76595: "TTY:
fix atime/mtime regression"), but it turns out that this was both
insufficient and overkill.
It was insufficient because we let people attach to the shared ptmx node
to see activity without even reading atime/mtime, and it was overkill
because the "only once a minute" means that you can't really tell an
idle person from an active one with 'w'.
So this tries to fix the problem properly. It marks the shared ptmx
node as un-notifiable, and it lowers the "only once a minute" to a few
seconds instead - still long enough that you can't time individual
keystrokes, but short enough that you can tell whether somebody is
active or not.
Reported-by: Simon Kirby <sim@hostway.ca>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull compat cleanup from Al Viro:
"Mostly about syscall wrappers this time; there will be another pile
with patches in the same general area from various people, but I'd
rather push those after both that and vfs.git pile are in."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
syscalls.h: slightly reduce the jungles of macros
get rid of union semop in sys_semctl(2) arguments
make do_mremap() static
sparc: no need to sign-extend in sync_file_range() wrapper
ppc compat wrappers for add_key(2) and request_key(2) are pointless
x86: trim sys_ia32.h
x86: sys32_kill and sys32_mprotect are pointless
get rid of compat_sys_semctl() and friends in case of ARCH_WANT_OLD_COMPAT_IPC
merge compat sys_ipc instances
consolidate compat lookup_dcookie()
convert vmsplice to COMPAT_SYSCALL_DEFINE
switch getrusage() to COMPAT_SYSCALL_DEFINE
switch epoll_pwait to COMPAT_SYSCALL_DEFINE
convert sendfile{,64} to COMPAT_SYSCALL_DEFINE
switch signalfd{,4}() to COMPAT_SYSCALL_DEFINE
make SYSCALL_DEFINE<n>-generated wrappers do asmlinkage_protect
make HAVE_SYSCALL_WRAPPERS unconditional
consolidate cond_syscall and SYSCALL_ALIAS declarations
teach SYSCALL_DEFINE<n> how to deal with long long/unsigned long long
get rid of duplicate logics in __SC_....[1-6] definitions
Add debugfs support to make it easier to print debug information
about the dma-buf buffers.
Cc: Dave Airlie <airlied@redhat.com>
[minor fixes on init and warning fix]
Cc: Dan Carpenter <dan.carpenter@oracle.com>
[remove double unlock in fail case]
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
For debugging purposes, it is useful to have a name-string added
while exporting buffers. Hence, dma_buf_export() is replaced with
dma_buf_export_named(), which additionally takes 'exp_name' as a
parameter.
For backward compatibility, and for lazy exporters who don't wish to
name themselves, a #define dma_buf_export() is also made available,
which adds a __FILE__ instead of 'exp_name'.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
[Thanks for the idea!]
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Bhanu Prakash Gollapudi