This driver has been tested on i.MX1/i.MX27/i.MX35 with an AT25 type
EEPROM and on i.MX27/i.MX31 with a Freescale MC13783 PMIC.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: Andrea Paterniani <a.paterniani@swapp-eng.it>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MBIMX27 is the evaluation board for CPUIMX27 and integrates : a
QVGA TFT, a SPI touchscreen controler, a SDCard connector wired to
SDHC1.
Signed-off-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
CPUIMX27 is built around Freescale's i.MX27 and has up to 64MB of
NOR Flash, up to 512MB of NAND Flash and up to 256MB of mDDR,
it includes an ethernet PHY in MII mode, an I2C RTC and a
ST16554 QuadUART on nCS3.
Signed-off-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The old defines leaked in from an old version of the patch.
Change the defines to match the register layout of the iomuxer.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for the MT9T031 CMOS camera sensor from Aptina to the PCM037
board. Also add two I2C iomux pin definitions, needed for pcm037. Also
remove now unneeded #ifdef CONFIG_I2C_IMX.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (417 commits)
MAINTAINERS: EB110ATX is not ebsa110
MAINTAINERS: update Eric Miao's email address and status
fb: add support of LCD display controller on pxa168/910 (base layer)
[ARM] 5552/1: ep93xx get_uart_rate(): use EP93XX_SYSCON_PWRCNT and EP93XX_SYSCON_PWRCN
[ARM] pxa/sharpsl_pm: zaurus needs generic pxa suspend/resume routines
[ARM] 5544/1: Trust PrimeCell resource sizes
[ARM] pxa/sharpsl_pm: cleanup of gpio-related code.
[ARM] pxa/sharpsl_pm: drop set_irq_type calls
[ARM] pxa/sharpsl_pm: merge pxa-specific code into generic one
[ARM] pxa/sharpsl_pm: merge the two sharpsl_pm.c since it's now pxa specific
[ARM] sa1100: remove unused collie_pm.c
[ARM] pxa: fix the conflicting non-static declarations of global_gpios[]
[ARM] 5550/1: Add default configure file for w90p910 platform
[ARM] 5549/1: Add clock api for w90p910 platform.
[ARM] 5548/1: Add gpio api for w90p910 platform
[ARM] 5551/1: Add multi-function pin api for w90p910 platform.
[ARM] Make ARM_VIC_NR depend on ARM_VIC
[ARM] 5546/1: ARM PL022 SSP/SPI driver v3
ARM: OMAP4: SMP: Update defconfig for OMAP4430
ARM: OMAP4: SMP: Enable SMP support for OMAP4430
...
Using the iMX serial driver with an IrDA device
needs extra peripheral settings and specific
timing depending on the transmitter circuitry used.
Signed-off-by: Fabian Godehardt <fg@emlix.com>
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sascha Hauer wrote:
> On Tue, Jun 02, 2009 at 04:18:42PM -0400, Daniel Schaeffer wrote:
>> Add basic support for the Logic i.MX27LITE board.
>>
>> Signed-off-by: Daniel Schaeffer <daniel.schaeffer@timesys.com>
>
> Besides the comment made by Fabio this looks ok to me.
>
> Sascha
>
>
Fixed issues pointed out by Fabio and Magnus, and rebased to mxc-master head.
Signed-off-by: Daniel Schaeffer <daniel.schaeffer@timesys.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Support code for lilly-1131 is implemented in a module/baseboard
fashion. All code specific to peripherals found on the development board
will go to this file.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds basic support for INCO startec's LILLY-1131 iMX31 based
modules. The module needs a baseboard support to work which will be
added in the next patch.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The i.MX31 PDK consists of several boards, one of them is a debug
board containing a CPLD which controls some debug leds, switch
buttons, an interrupt chip and an Ethernet controller.
This patch adds support for detecting if the PDK board is present
(during boot) and adds the interrupt chip to the kernel.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since iomux code is not directly related to gpio on mx31, the calls
to gpio_request are removed from iomux.c file.
These calls have to be done in platform initialization files. The
name of the singe pin call for iomux is also changed to
mxc_iomux_alloc_pin.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Several comments in board config files stated "mandatory for
CONFIG_LL_DEBUG" but the correct name is CONFIG_DEBUG_LL.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As suggested by Sascha, I regroup them in a single patch so that the
other patches become more orthogonal.
changes since v1: changed I2C1 pin names
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This hw-random driver add support to RNGA hardware found
on some i.MX processors.
Signed-off-by: Alan Carvalho de Assis <acassis@gmail.com>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* Kconfig enables now HAVE_PWM (this enables in turn the selection of
CONFIG_BACKLIGHT_PWM)
* changes CONFIG_ARCH_MXyy to CONFIG_MACH_MXyy
* fix some register names to match those of the reference manual
* write a stub code so that the PWM can be used to program the
LCD backlight
* convert from #ifdef CONFIG_ARCH_MXxx to cpu_is_mxXX()
* remove unneeded defines and fix 80-column "violations" of checkpatch.pl
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer