The mdiobus_scan logic is currently hardcoded to only
work with c22 devices. This works fairly well in most
cases, but its possible that a c45 device doesn't respond
despite being a standard phy. If the parent hardware
is capable, it makes sense to scan for c22 devices before
falling back to c45.
As we want this to reflect the capabilities of the STA,
lets add a field to the mii_bus structure to represent
the capability. That way devices can opt into the extended
scanning. Existing users should continue to default to c22
only scanning as long as they are zero'ing the structure
before use.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vaibhav Gupta says:
====================
ethernet: dec: tulip: use generic power management
Linux Kernel Mentee: Remove Legacy Power Management.
The purpose of this patch series is to remove legacy power management
callbacks and invocation of PCI helper functions, from tulip ethernet drivers.
With legacy PM, drivers themselves are responsible for handling the device's
power states. And they do this with the help of PCI helper functions like
pci_enable/disable_device(), pci_set/restore_state(), pci_set_powr_state(), etc.
which is not recommended.
In generic PM, all the required tasks are handled by PCI core and drivers need
to perform device-specific operations only.
All patches are compile-tested only.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With the support of generic PM callbacks, drivers no longer need to use
legacy .suspend() and .resume() in which they had to maintain PCI states
changes and device's power state themselves.
Legacy PM involves usage of PCI helper functions like pci_enable_wake()
which is no longer recommended.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the support of generic PM callbacks, drivers no longer need to use
legacy .suspend() and .resume() in which they had to maintain PCI
states changes and device's power state themselves.
Earlier, .suspend() and .resume() were invoking pci_disable_device()
and pci_enable_device() respectively to manage the device's power state.
driver also invoked pci_save/restore_state() and pci_set_power_sitate().
With generic PM, it is no longer needed. The driver is expected to just
implement driver-specific operations and leave power transitions to PCI
core.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the support of generic PM callbacks, drivers no longer need to use
legacy .suspend() and .resume() in which they had to maintain PCI states
changes and device's power state themselves.
Earlier, .suspend() and .resume() were invoking pci_disable_device()
and pci_enable_device() respectively to manage the device's power state.
With generic PM, it is no longer needed. The driver is expected to just
implement driver-specific operations and leave power transitions to PCI
core.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With stable support of generic PM callbacks, drivers no longer need to use
legacy .suspend() and .resume() in which they had to maintain PCI states
changes and device's power state themselves.
Earlier, .resume() was invoking pci_enable_device(). Drivers should not
call PCI legacy helper functions, hence, it was removed. This should not
change the behavior of the device as this function is called by PCI core
if somehow pm_ops is not able to bind with the driver, else, required tasks
are managed by the core itself.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With legacy PM hooks, it was the responsibility of a driver to manage PCI
states and also the device's power state. The generic approach is to let the
PCI core handle the work.
The legacy suspend() and resume() were making use of
pci_read/write_config_dword() to enable/disable wol. Driver editing
configuration registers of a device is not recommended. Thus replace them
all with device_wakeup_enable/disable().
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vaibhav Gupta says:
====================
ethernet: amd: Convert to generic power management
Linux Kernel Mentee: Remove Legacy Power Management.
The purpose of this patch series is to remove legacy power management callbacks
from amd ethernet drivers.
The callbacks performing suspend() and resume() operations are still calling
pci_save_state(), pci_set_power_state(), etc. and handling the power management
themselves, which is not recommended.
The conversion requires the removal of the those function calls and change the
callback definition accordingly and make use of dev_pm_ops structure.
All patches are compile-tested only.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dev_pm_ops structure to call generic suspend() and resume() callbacks.
Drivers should avoid saving device register and/or change power states
using PCI helper functions. With the generic approach, all these are handled
by PCI core.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers should not save device registers and/or change the power state of
the device. As per the generic PM approach, these are handled by PCI core.
The driver should support dev_pm_ops callbacks and bind them to pci_driver.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove legacy PM callbacks and use generic operations. With legacy code,
drivers were responsible for handling PCI PM operations like
pci_save_state(). In generic code, all these are handled by PCI core.
The generic suspend() and resume() are called at the same point the legacy
ones were called. Thus, it does not affect the normal functioning of the
driver.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev cannot be NULL here since its already being accessed
before. Remove the redundant null check.
Signed-off-by: Gaurav Singh <gaurav1086@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb cannot be NULL here since its already being accessed
before: sock_net(skb->sk). Remove the redundant null check.
Signed-off-by: Gaurav Singh <gaurav1086@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes. Also, remove unnecessary
function ipv6_rpl_srh_alloc_size() and replace kzalloc() with kcalloc(),
which has a 2-factor argument form for multiplication.
This code was detected with the help of Coccinelle and, audited and
fixed manually.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev cannot be NULL here since its already being accessed
before. Remove the redundant null check.
Signed-off-by: Gaurav Singh <gaurav1086@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
net: address some sparse warnings
This series adds missing declarations and move others to
address W=1 C=1 warnings in tcp and udp.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes following warnings :
CC net/ipv4/udp_offload.o
net/ipv4/udp_offload.c:504:17: warning: no previous prototype for 'udp4_gro_receive' [-Wmissing-prototypes]
504 | struct sk_buff *udp4_gro_receive(struct list_head *head, struct sk_buff *skb)
| ^~~~~~~~~~~~~~~~
net/ipv4/udp_offload.c:584:29: warning: no previous prototype for 'udp4_gro_complete' [-Wmissing-prototypes]
584 | INDIRECT_CALLABLE_SCOPE int udp4_gro_complete(struct sk_buff *skb, int nhoff)
| ^~~~~~~~~~~~~~~~~
CHECK net/ipv6/udp_offload.c
net/ipv6/udp_offload.c:115:16: warning: symbol 'udp6_gro_receive' was not declared. Should it be static?
net/ipv6/udp_offload.c:148:29: warning: symbol 'udp6_gro_complete' was not declared. Should it be static?
CC net/ipv6/udp_offload.o
net/ipv6/udp_offload.c:115:17: warning: no previous prototype for 'udp6_gro_receive' [-Wmissing-prototypes]
115 | struct sk_buff *udp6_gro_receive(struct list_head *head, struct sk_buff *skb)
| ^~~~~~~~~~~~~~~~
net/ipv6/udp_offload.c:148:29: warning: no previous prototype for 'udp6_gro_complete' [-Wmissing-prototypes]
148 | INDIRECT_CALLABLE_SCOPE int udp6_gro_complete(struct sk_buff *skb, int nhoff)
| ^~~~~~~~~~~~~~~~~
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes following (C=1 W=1) warnings for CONFIG_RETPOLINE=y :
net/ipv4/tcp_offload.c:306:16: warning: symbol 'tcp4_gro_receive' was not declared. Should it be static?
net/ipv4/tcp_offload.c:306:17: warning: no previous prototype for 'tcp4_gro_receive' [-Wmissing-prototypes]
net/ipv4/tcp_offload.c:319:29: warning: symbol 'tcp4_gro_complete' was not declared. Should it be static?
net/ipv4/tcp_offload.c:319:29: warning: no previous prototype for 'tcp4_gro_complete' [-Wmissing-prototypes]
CHECK net/ipv6/tcpv6_offload.c
net/ipv6/tcpv6_offload.c:16:16: warning: symbol 'tcp6_gro_receive' was not declared. Should it be static?
net/ipv6/tcpv6_offload.c:29:29: warning: symbol 'tcp6_gro_complete' was not declared. Should it be static?
CC net/ipv6/tcpv6_offload.o
net/ipv6/tcpv6_offload.c:16:17: warning: no previous prototype for 'tcp6_gro_receive' [-Wmissing-prototypes]
16 | struct sk_buff *tcp6_gro_receive(struct list_head *head, struct sk_buff *skb)
| ^~~~~~~~~~~~~~~~
net/ipv6/tcpv6_offload.c:29:29: warning: no previous prototype for 'tcp6_gro_complete' [-Wmissing-prototypes]
29 | INDIRECT_CALLABLE_SCOPE int tcp6_gro_complete(struct sk_buff *skb, int thoff)
| ^~~~~~~~~~~~~~~~~
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Declare ipv4_specific once, in tcp.h were it belongs.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6_specific should be declared in tcp include files,
not mptcp.
This removes the following warning :
CHECK net/ipv6/tcp_ipv6.c
net/ipv6/tcp_ipv6.c:78:42: warning: symbol 'ipv6_specific' was not declared. Should it be static?
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove these errors:
net/ipv6/tcp_ipv6.c:1550:29: warning: symbol 'tcp_v6_rcv' was not declared. Should it be static?
net/ipv6/tcp_ipv6.c:1770:30: warning: symbol 'tcp_v6_early_demux' was not declared. Should it be static?
net/ipv6/tcp_ipv6.c:1550:29: warning: no previous prototype for 'tcp_v6_rcv' [-Wmissing-prototypes]
1550 | INDIRECT_CALLABLE_SCOPE int tcp_v6_rcv(struct sk_buff *skb)
| ^~~~~~~~~~
net/ipv6/tcp_ipv6.c:1770:30: warning: no previous prototype for 'tcp_v6_early_demux' [-Wmissing-prototypes]
1770 | INDIRECT_CALLABLE_SCOPE void tcp_v6_early_demux(struct sk_buff *skb)
| ^~~~~~~~~~~~~~~~~~
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Realtek added new members to the RTL8125 chip family, therefore rename
RTL8125 to RTL8125a. Then we use the same chip naming as in the r8125
vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than requiring every hw crypto capable NIC driver to do a check for
slave_dev being set, set real_dev in the xfrm layer and xso init time, and
then override it in the bonding driver as needed. Then NIC drivers can
always use real_dev, and at the same time, we eliminate the use of a
variable name that probably shouldn't have been used in the first place,
particularly given recent current events.
CC: Boris Pismenny <borisp@mellanox.com>
CC: Saeed Mahameed <saeedm@mellanox.com>
CC: Leon Romanovsky <leon@kernel.org>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jakub Kicinski <kuba@kernel.org>
CC: Steffen Klassert <steffen.klassert@secunet.com>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: netdev@vger.kernel.org
Suggested-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Bump firmware version to XX.2007.1168
Petr says:
In patch #1, bump the firmware version required by the driver to
XX.2007.1168. This version fixes several issues observed in the
offloaded datapath.
In patch #2, add support for requiring FW version on Spectrum-3 (so far
only Spectrum-1 and Spectrum-2 have had this requirement). Demand the
same version as mentioned above.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In a fashion similar to the other Spectrum systems, enforce a specific
firmware version for Spectrum-3 so that the driver and firmware are
always in sync with regards to new features.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This version comes with fixes to the following problems, among others:
- Wrong shaper configuration on Spectrum-1
- Bogus temperature reading on Spectrum-2
- Problems in setting egress buffer size after MTU change on Spectrum-2
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was reported that a considerable amount of cycles were spent on the
expensive indirect calls on fib6_rule_lookup. This patch introduces an
inline helper called pol_route_func that uses the indirect_call_wrappers
to avoid the indirect calls.
This patch saves around 50ns per call.
Performance was measured on the receiver by checking the amount of
syncookies that server was able to generate under a synflood load.
Traffic was generated using trafgen[1] which was pushing around 1Mpps on
a single queue. Receiver was using only one rx queue which help to
create a bottle neck and make the experiment rx-bounded.
These are the syncookies generated over 10s from the different runs:
Whithout the patch:
TcpExtSyncookiesSent 3553749 0.0
TcpExtSyncookiesSent 3550895 0.0
TcpExtSyncookiesSent 3553845 0.0
TcpExtSyncookiesSent 3541050 0.0
TcpExtSyncookiesSent 3539921 0.0
TcpExtSyncookiesSent 3557659 0.0
TcpExtSyncookiesSent 3526812 0.0
TcpExtSyncookiesSent 3536121 0.0
TcpExtSyncookiesSent 3529963 0.0
TcpExtSyncookiesSent 3536319 0.0
With the patch:
TcpExtSyncookiesSent 3611786 0.0
TcpExtSyncookiesSent 3596682 0.0
TcpExtSyncookiesSent 3606878 0.0
TcpExtSyncookiesSent 3599564 0.0
TcpExtSyncookiesSent 3601304 0.0
TcpExtSyncookiesSent 3609249 0.0
TcpExtSyncookiesSent 3617437 0.0
TcpExtSyncookiesSent 3608765 0.0
TcpExtSyncookiesSent 3620205 0.0
TcpExtSyncookiesSent 3601895 0.0
Without the patch the average is 354263 pkt/s or 2822 ns/pkt and with
the patch the average is 360738 pkt/s or 2772 ns/pkt which gives an
estimate of 50 ns per packet.
[1] http://netsniff-ng.org/
Changelog since v1:
- Change ordering in the ICW (Paolo Abeni)
Cc: Luigi Rizzo <lrizzo@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Brian Vazquez <brianvv@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are many places where 2 annotations are not enough. This patch
adds INDIRECT_CALL_3 and INDIRECT_CALL_4 to cover such cases.
Signed-off-by: Brian Vazquez <brianvv@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a spelling typo in spectrum_dcb.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keepalived can set global static ip routes or virtual ip routes dynamically
following VRRP protocol states. Using a dedicated rtm_protocol will help
keeping track of it.
Changes in v2:
- fix tab/space indenting
Signed-off-by: Alexandre Cassen <acassen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh says:
====================
net: atlantic: additional A2 features
This patchset adds more features to A2:
* half duplex rates;
* EEE;
* flow control;
* link partner capabilities reporting;
* phy loopback.
Feature-wise A2 is almost on-par with A1 save for WoL and filtering, which
will be submitted as separate follow-up patchset(s).
====================
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the phy loopback support on A2.
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds link partner capabilities reporting support on A2.
In particular, the following capabilities are available for reporting:
* link rate;
* EEE;
* flow control.
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds flow control support on A2.
Co-developed-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds EEE support on A2.
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Co-developed-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes 2.5G baseX wrong usage/reporting, since it shouldn't have
been mixed with baseT.
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for 10M/100M/1G half duplex rates, which are
supported by A2 in additional to full duplex rates supported by A1.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
arg cannot be NULL since its already being dereferenced
before. Remove the redundant NULL check.
Signed-off-by: Gaurav Singh <gaurav1086@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the mtk_eth_soc driver to use the finalised link parameters in
mac_link_up() rather than the parameters in mac_config().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
Multicast improvement in Ocelot and Felix drivers
This series makes some basic multicast forwarding functionality work for
Felix DSA and for Ocelot switchdev. IGMP/MLD snooping in Felix is still
missing, and there are other improvements to be made in the general area
of multicast address filtering towards the CPU, but let's get these
hardware-specific fixes out of the way first.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The current procedure for installing a multicast address is hardcoded
for IPv4. But, in the ocelot hardware, there are 3 different procedures
for IPv4, IPv6 and for regular L2 multicast.
For IPv6 (33-33-xx-xx-xx-xx), it's the same as for IPv4
(01-00-5e-xx-xx-xx), except that the destination port mask is stuffed
into first 2 bytes of the MAC address except into first 3 bytes.
For plain Ethernet multicast, there's no port-in-address stuffing going
on, instead the DEST_IDX (pointer to PGID) is used there, just as for
unicast. So we have to use one of the nonreserved multicast PGIDs that
the hardware has allocated for this purpose.
This patch classifies the type of multicast address based on its first
bytes, then redirects to one of the 3 different hardware procedures.
Note that this gives us a really better way of redirecting PTP frames
sent at 01-1b-19-00-00-00 to the CPU. Previously, Yangbo Lu tried to add
a trapping rule for PTP EtherType but got a lot of pushback:
https://patchwork.ozlabs.org/project/netdev/patch/20190813025214.18601-5-yangbo.lu@nxp.com/
But right now, that isn't needed at all. The application stack (ptp4l)
does this for the PTP multicast addresses it's interested in (which are
configurable, and include 01-1b-19-00-00-00):
memset(&mreq, 0, sizeof(mreq));
mreq.mr_ifindex = index;
mreq.mr_type = PACKET_MR_MULTICAST;
mreq.mr_alen = MAC_LEN;
memcpy(mreq.mr_address, addr1, MAC_LEN);
err1 = setsockopt(fd, SOL_PACKET, PACKET_ADD_MEMBERSHIP, &mreq,
sizeof(mreq));
Into the kernel, this translates into a dev_mc_add on the switch network
interfaces, and our drivers know that it means they should translate it
into a host MDB address (make the CPU port be the destination).
Previously, this was broken because all mdb addresses were treated as
IPv4 (which 01-1b-19-00-00-00 obviously is not).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current iterators are impossible to understand at first glance
without switching back and forth between the definitions and their
actual use in the for loops.
So introduce some convenience names to help readability.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the mdb hooks in felix and exports the mdb functions from
ocelot.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When used in DSA mode (as seen in Felix), the DEST_IDX in the MAC table
should point to the PGID for the CPU port (PGID_CPU) and not for the
Ethernet port where the CPU queues are redirected to (also known as Node
Processor Interface - NPI).
Because for Felix this distinction shouldn't really matter (from DSA
perspective, the NPI port _is_ the CPU port), make the ocelot library
act upon the CPU port when NPI mode is enabled. This has no effect for
the mscc_ocelot driver for VSC7514, because that does not use NPI (and
ocelot->npi is -1).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot hardware designers have made some hacks to support multicast
IPv4 and IPv6 addresses. Normally, the MAC table matches on MAC
addresses and the destination ports are selected through the DEST_IDX
field of the respective MAC table entry. The DEST_IDX points to a Port
Group ID (PGID) which contains the bit mask of ports that frames should
be forwarded to. But there aren't a lot of PGIDs (only 80 or so) and
there are clearly many more IP multicast addresses than that, so it
doesn't scale to use this PGID mechanism, so something else was done.
Since the first portion of the MAC address is known, the hack they did
was to use a single PGID for _flooding_ unknown IPv4 multicast
(PGID_MCIPV4 == 62), but for known IP multicast, embed the destination
ports into the first 3 bytes of the MAC address recorded in the MAC
table.
The VSC7514 datasheet explains it like this:
3.9.1.5 IPv4 Multicast Entries
MAC table entries with the ENTRY_TYPE = 2 settings are interpreted
as IPv4 multicast entries.
IPv4 multicasts entries match IPv4 frames, which are classified to
the specified VID, and which have DMAC = 0x01005Exxxxxx, where
xxxxxx is the lower 24 bits of the MAC address in the entry.
Instead of a lookup in the destination mask table (PGID), the
destination set is programmed as part of the entry MAC address. This
is shown in the following table.
Table 78: IPv4 Multicast Destination Mask
Destination Ports Record Bit Field
---------------------------------------------
Ports 10-0 MAC[34-24]
Example: All IPv4 multicast frames in VLAN 12 with MAC 01005E112233 are
to be forwarded to ports 3, 8, and 9. This is done by inserting the
following entry in the MAC table entry:
VALID = 1
VID = 12
MAC = 0x000308112233
ENTRY_TYPE = 2
DEST_IDX = 0
But this procedure is not at all what's going on in the driver. In fact,
the code that embeds the ports into the MAC address looks like it hasn't
actually been tested. This patch applies the procedure described in the
datasheet.
Since there are many other fixes to be made around multicast forwarding
until it works properly, there is no real reason for this patch to be
backported to stable trees, or considered a real fix of something that
should have worked.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Offload TC action pedit munge tcp/udp sport/dport
Petr says:
On Spectrum-2 and Spectrum-3, it is possible to overwrite L4 port number of
a TCP or UDP packet in the ACL engine. That corresponds to the pedit munges
of tcp and udp sport resp. dport fields. Offload these munges on the
systems where they are supported.
The current offloading code assumes that all systems support the same set
of fields. This now changes, so in patch #1 first split handling of pedit
munges by chip type. The analysis of which packet field a given munge
describes is kept generic.
Patch #2 introduces the new flexible action fields. Patch #3 then adds the
new pedit fields, and dispatches on them on Spectrum>1.
Patch #4 adds a forwarding selftest for pedit dsfield, applicable to SW as
well as HW datapaths.
====================
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test that checks that pedit adjusts port numbers of tcp and udp
packets.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum-2 supports an ACL action L4_PORT, which allows TCP and UDP source
and destination port number change. Offload suitable mangles to this
action.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add fields related to L4_PORT_ACTION, which is used for changing of TCP and
UDP port numbers.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeremy Linton