The function hdmi_audio_trigger is a callback used by ASoC to stop/start
HDMI audio. Also, it does not perform IP-specific configuration directly.
Hence, it should be placed in the general portion of the HDMI driver,
along with the other ASoC callbacks.
Also, make this function static.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In order to separate clearly IP-specific code from general DSS code,
a function for OMAP4 audio enable is created. This function is
included in the HDMI IP ops to align with the current implementation
of the DSS HDMI driver. This function is to be used by the ASoC
HDMI audio codec.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
These functions require access to IP-secific data. However, it is not possible
to pass such data as a function argument as such functions have a specific
signature specified by ASoC. Instead, they will have access to the IP-specific
data by calling snd_soc_codec_get_drvdata. The codec driver data is set
at probe time.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Under the new DSS architecture for HDMI, there is a clear separation
between general DSS code and HDMI IP-specific data. Functions
that require access to the HDMI driver IP-specific data receive an
hdmi_ip_data structure. The ASoC codec require access to such
IP-specific data. Then, instead of accessing it directly, it will be
passed as codec driver data. This also helps to have a clear separation
between DSS and ASoC portions of the code.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Clock requirements for scaling in OMAP2, OMAP3 and OMAP4 are different. In
OMAP2 and OMAP3 the required clock rate is a function of pixel clock, vertical
downscale ratio and horizontal downscale ratio whereas in OMAP4 it is a
function of pixel clock and horizontal downscale ratio only. Selection of 3-tap
vs 5-tap coefficients depends on clock rate line buffer width in OMAP3 whereas
in OMAP4 it is independent of clock rate and line buffer width. In OMAP2 3-tap
for vertical and 5-tap for horizontal scaling is used. In OMAP4 5-tap is used
both for horizontal and vertical scaling for better performance. Also, the
number and width of line buffers differs in OMAP3 and OMAP4.
So, clock functions have been fined tuned for OMAP3 and support has been added
added for OMAP4. This code has been tested on OMAP2, OMAP3 and OMAP4, and
scaling issues due to clock errors have been resolved.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The FIR coefficients present in kernel are being updated to new coefficients
consisting of 24 coefficient tables, with 12 each for 3 tap and 5 tap scenario,
which are chosen on the basis of DISPC up/downsampling filters M value. M is
the inverse of low pass cut off frequency of the sampling filter. For vertical
scaling 3 tap or 5 tap tables are used based on the clock rate and width of
the line buffer whereas in OMAP2 3 tap is always used. For horizontal scaling
however 5 tap tables are always used.
New coefficients and the corresponding logic have been tested on OMAP2, OMAP3
and OMAP4. Horizontal and vertical scaling worked fine except for some 3 tap
vs 5 tap issue during vertical upscaling and clock failing issues which is
acknowledged in the next patch. Vertical upscaling was found to perform better
under 5 taps. The 24 coefficient tables have been moved to another file
dispc_coefs.c for proper maintainance.
This code is written based on code written by Lajos Molnar <lajos@ti.com> in
Android Kernel for scaling. Lajos Molnar <lajos@ti.com> had fine tuned the FIR
coefficient selection process and reduced outliness and blockiness around
images when upscaling more than 2 times.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
extra_info_update_ongoing() goes through all overlays, but doesn't check
if the overlay is connected to a manager. This leads to a crash whenever
an overlay has been detached.
Add a check to skip the non-connected overlays.
Reported-by: Rob Clark <rob@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Make PICODLP driver on OMAP2_DSS_DPI since it is the display interface it uses.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The display state parameter of omap_dss_device struct is not being set correctly
in the panel driver NEC panel driver panel-nec-nl8048hl11-01b.c. Set the correct
states in the panel's enable/disable/suspend/resume functions.
CC: Erik Gilling <konkers@android.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The clock names of DSI_PLL_HSDIV_DISPC and DSI_PLL_HSDIV_DSI was made
dynamic based on the current value of DISPC and DSI FCLK sources. This
doesn't need to be done since we are just interested in the clock names,
and not the current clock sources for DISPC and DSI FCLKs.
Use only the generic and omap specific names for the DSI PLL's HSDIV
clocks.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The functions dss_ovl_simple_check() and dss_mgr_simple_check() are not
really part of the apply mechanism, and can be moved to overlay.c and
manager.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The dispc's error handler tries to disable all outputs when OCP_ERR
happens. However, the code doesn't check if there actually is a display
on each particular output, nor if there's a driver for the display. This
may lead to NULL pointer reference.
Signed-off-by: Rob Clark <rob@ti.com>
[tomi.valkeinen@ti.com: added patch description]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The functions dss_ovl_check, dss_mgr_check_zorder, dss_mgr_check in
apply.c are not really part of the apply mechanism, and can be moved to
overlay.c and manager.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This resolves the conflict in the
drivers/staging/iio/industrialio-core.c file due to two different
changes made to resolve the same problem.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In ancient times it was necessary to manually initialize the bus field of an
spi_driver to spi_bus_type. These days this is done in spi_driver_register(),
so we can drop the manual assignment.
The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
.driver = {
- .bus = &spi_bus_type,
},
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Current code will always write fifo threshold values to the register,
even if they are the same as previously. Separate the setting of fifo
fields into a separate function, and only set new values if they are
different than the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently fifo threshold configuration is done per overlay or per
manager. However, when a fifo size configuration is added, we need to
always configure the thresholds for all overlays.
This patch prepares for that by changing the fifo threshold
configuration to always handle all overlays.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When we are enabling an overlay, there's a point in time when the
overlay is not actually enabled yet (nor do we want it to be enabled),
but we do want to check if the configuration for the overlay is valid,
and to calculate correct fifo thresholds for the soon-to-be-enabled
overlay.
Current code handled this in a hacky way, setting op->enabled to true
temporarily when calling functions that need to consider the state when
the overlay is enabled.
This patch makes this a bit cleaner, adding "enabling" field, which is
set when the overlay is not yet enabled but should be considered in the
checks and calculations.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently dss_write_regs() implicitely sets the GO bits for all managers
with shadow dirty flags set. This is a bit misleading, as one does not
presume "write registers" function to also set the GO bit.
Thus this patch splits the setting of GO bits into a separate function,
dss_set_go_bits, which is used after writing the registers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In the apply irq handler the code currently clears the shadow dirty
flags whenever the manager in question is not busy (i.e. GO bit is
down). However, this is not quite right, as the GO bit may have never
been set.
While not done in the current code, the above would cause bug in
scenario where the registers are written, and thus shadow_dirty flag is
set, but the GO bit will be set only later. In this case the
shadow_dirty flags would be cleared, even if the HW is not using the new
configurations.
This patch fixes the issue by clearing the shadow flags only when the GO
bit is clear, and the GO bit had been set.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
need_isr() should return true whenever there's work that needs to be
handled in the VSYNC/FRAMEDONE irq handler. However, need_isr() is
missing some cases where we need the irq handler.
This patch adds checks for shadow dirty flags, so that the irq handler
is started/kept running while shadow dirty flags are set.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
extra_info_update_ongoing() skipped checks for overlays that were marked
as disabled. This doesn't work, as the enable status of an overlay is in
the extra_info group, and thus extra_info_update_ongoing() reports false
when we are disabling an overlay. This causes
wait_pending_extra_info_updates() to not wait for the ongoing overlay
disable.
This patch changes extra_info_update_ongoing() to check the state of
overlays marked as disabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that dss_mgr_enable returns an error value, check it in all the
places dss_mgr_enable is used, and bail out properly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add checks for overlay and manager settings. The checks are a bit
complex, as we need to observe the bigger picture instead of overlays
and managers independently. Things like the used display and the zorder
of other overlays affect the validity of the settings.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add dss_mgr_simple_check() which is used to check the validity of
certain manager attributes. Only attributes that can be checked
independently, without knowing the display being used, is done here
(thus "simple").
We can use this function in dss_mgr_set_info().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add dss_ovl_simple_check() which is used to check the validity of
certain overlay attributes. Only attributes that can be checked
independently, without knowing the display being used, is done here
(thus "simple").
We can use this function in dss_ovl_set_info().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
apply.c no longer touches any registers if an output is not enabled.
This means that we don't need to do dispc_runtime_get() anymore, and the
calls can be removed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add wait_pending_extra_info_updates() function which can be used to wait
until any extra_info changes have been taken into use by the hardware.
This can be only called when holding the apply mutex, so that other
threads cannot insert new extra_info changes.
This will be used to handle fifo-configurations.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add checks to dss_mgr_enable, dss_mgr_disable, dss_ovl_enable,
dss_ovl_disable that check if the state is already the same as given in
the parameters, and exit if so.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add a helper function dss_apply_ovl_enable(), which is similar to the
main apply() function: dss_apply_ovl_enable() applies the given overlay
enable-status to ovl_priv_data, and sets the dirty flag.
The difference between the helper function and the previous direct use
of the fields is that the helper function will not do anything if the
enable state is already the same as given in the parameter.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_overlay_manager contains device_changed field, which no longer has
any use. So remove the field and the few places where it is touched.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Rename ovl_priv_data's and mgr_priv_data's dirty and shadow_dirty fields
to info_dirty and shadow_info_dirty to better reflect what they mean.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Setting overlay's fifo thresholds is currently handled at the same time
as other overlay attributes. This is not right, as the normal attributes
should only affect one overlay and manager, but changing the fifo
thresholds are needed in cases like fifo-merge, where multiple managers
are affected.
This patch moves the channel field into the "extra_info" set, handled
together with channel and enabled-status.
This also lets us to calculate the fifos only when needed, specifically,
when an overlay or a manager is enabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Setting overlay's output channel is currently handled at the same time
as other overlay attributes. This is not right, as the normal attributes
should only affect one overlay and manager, but changing the channel
affects two managers.
This patch moves the channel field into the "extra_info" set, handled
together with enabled-status.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
struct omap_overlayr contains info and info_dirty fields, both of which
should be internal to apply.c.
This patch moves those fields into ovl_priv data, and names them
user_info and user_info_dirty.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
struct omap_overlay_manager contains info and info_dirty fields, both of
which should be internal to apply.c.
This patch moves those fields into mgr_priv data, and names them
user_info and user_info_dirty.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add a helper function mgr_clear_shadow_dirty(), which clears the
shadow_dirty flags for the given manager and for the overlays on that
manager.
This lets us simplify the code in the dss_apply_irq_handler().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add "updating" flag to mgr_priv_data, which is used to track whether the
manager is currently actively working, i.e. updating the screen.
For auto-update displays updating is always true when the display is
enabled, but for manual update displays the flag is true only during
frame transfers.
The flag is used to manage registers properly, for example when updating
is false and a register for a manager is written, there's no need to set
shadow_dirty flag nor set the GO bit, as the settings will be taken into
use by the HW automatically when the output is enabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add dispc_mgr_get_framedone_irq() which returns the irq number for
FRAMEDONE for the given channel.
Note that the function returns always 0 for DIGIT channel, even if OMAP4
does have FRAMEDONE_TV interrupt. The reason for this is that this
function is currently used only to track manual updates, and thus
FRAMEDONE_TV is not needed.
If there's need in the future to also get the FRAMEDONE_TV this needs
revisiting. However, as FRAMEDONE_TV doesn't exist on OMAP2/3, the use
of this function for that purpose needs some extra code to handle the
OMAP2/3 case.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The functions writing to the DISPC registers in apply.c are more complex
than needed. This patch cleans things up.
Two helper functions are added: need_isr(), which returns if an isr for
VSYNC is needed, and need_go(), which tells if there has been a write to
the shadow registers and we need to set the GO bit.
The functions that call the actual dispc write functions will set the
dirty and shadow_dirty flags themselves, instead of that being done on
the caller side. The writing functions also check if the dirty flag is
even set, and return immediately if not.
This allows us to clean up dss_write_regs().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Overlays are currently enabled and disabled with a boolean in the struct
omap_overlay_info. The overlay info is set with ovl->set_overlay_info(),
and made into use with mgr->apply().
This doesn't work properly, as the enable/disable status may affect also
other overlays, for example when using fifo-merge. Thus the enabling and
disabling of the overlay needs to be done outside the normal overlay
configuration.
This patch achieves that by doing the following things:
1) Add function pointers to struct omap_overlay: enable(), disable() and
is_enabled(). These are used to do the obvious. The functions may block.
2) Move the "enabled" field from struct omap_overlay to ovl_priv_data.
3) Add a new route for settings to be applied to the HW, called
"extra_info". The status of the normal info and extra_info are tracked
separately.
The point here is to allow the normal info to be changed and
applied in non-blocking matter, whereas the extra_info can only be
changed when holding the mutex. This makes it possible to, for example,
set the overlay enable flag, apply it, and wait until the HW has taken
the flag into use.
This is not possible if the enable flag would be in the normal info, as
a new value for the flag could be set at any time from the users of
omapdss.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add a new field to mgr_priv data, "busy", which is used to track the
status of GO bit with the manager. As manual update displays never use
the GO bit, the field is always false for managers used for manual
update displays.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
struct omap_overlay_manager contains "enabled"-field, used to track if
the manager is enabled or not. This field should be internal to apply.c.
This patch moves the field to mgr_priv_data, and applies the necessary
locking when accessing the field.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The current code uses dsi_video_mode_enable/disable functions to
enable/disable DISPC output for video mode displays. For command mode
displays we have no notion in the DISPC side of whether the panel is
enabled, except when a dss_mgr_start_update() call is made.
However, to properly maintain the DISPC state in apply.c, we need to
know if a manager used for a manual update display is currently in use.
This patch achieves that by changing dsi_video_mode_enable/disable to
dsi_enable/disable_video_output, which is called by both video and
command mode displays. For video mode displays it starts the actual
pixel stream, as it did before. For command mode displays it doesn't do
anything else than mark that the manager is currently in use.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The functions in apply.c, called mostly via function pointers in overlay
and overlay_manager structs, will be divided into two groups. The other
group will not sleep and can be called from interrupts, and the other
group may sleep.
The idea is that the non-sleeping functions may only change certain
settings in overlays and managers, and those settings may only affect
the particular overlay/manager. For example, set the base address of the
overlay.
The blocking functions, however, will handle more complex configuration
changes. For example, when an overlay is enabled and fifo-merge feature
is used, we need to do the enable in multiple steps, waiting in between,
and the change affects multiple overlays and managers.
apply.c already contains a spinlock, which has been used to protect
(badly) the dss_data. This patch adds locks/unlocks of the spinlock to
the missing places, and the lock should now properly protect dss_data.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The functions in apply.c, called mostly via function pointers in overlay
and overlay_manager structs, will be divided into two groups. The first
group will not sleep and can be called from interrupts, and the second
group may sleep.
The idea is that the non-sleeping functions may only change certain
settings in overlays and managers, and those settings may only affect
the particular overlay/manager. For example, set the base address of the
overlay.
The blocking functions, however, will handle more complex configuration
changes. For example, when an overlay is enabled and fifo-merge feature
is used, we need to do the enable in multiple steps, waiting in between,
and the change affects multiple overlays and managers.
This patch adds the mutex which is used in the blocking functions to
have exclusive access to overlays and overlay managers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DSS currently tries to check that the given overlay and overlay manager
settings are acceptable, but the code does not work quite properly.
Things may change between the check and the actual use of the settings.
Furthermore, the following patches will rewrite how settings are
configured and managed, and trying to keep the (broken) settings
checking working during the rewrite would be very difficult.
This patch removes the checking code, and a working version of checking
will be added back after the settings rewrite has been done.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
apply.c will handle the management of dispc in the future patches. This
patch moves overlay manager related functions to apply.c so that they
will have access to the private data and functions of apply.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
apply.c will handle the management of dispc in the future patches. This
patch moves overlay related functions to apply.c so that they will have
access to the private data and functions of apply.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dss_cache struct contains private data used to manage dispc. "cache" is
not a good word for it, so rename it to dss_data.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dss_cache struct contains a spinlock used to protect the struct. A more
logical place for the spinlock is outside the struct that it is
protecting. So move it there.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
manager_cache_data is not a suitable name for the struct. It is more of
a private data for the manager.
Rename the struct to mgr_priv_data, and add a function,
get_mgr_priv(mgr), to get a pointer to the data.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
overlay_cache_data is not a suitable name for the struct. It is more of
a private data for the overlay.
Rename the struct to ovl_priv_data, and add a function,
get_ovl_priv(ovl), to get a pointer to the data.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Make configure_overlay() and configure_manager() take overlay/manager
pointer as an argument, instead of the ovl/mgr id. This will be useful
with the future patches.
Also rename the functions to be a bit more informative:
dss_ovl_write_regs, dss_mgr_write_regs, dss_write_regs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use dispc_mgr_get_vsync_irq() to get the interrupt numbers for vsync,
instead of hardcoding the values depending on the display type.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Current way of handling overlay-manager links is a bit strange: each
manager has a static array, containing pointers to all the overlays
(even those used by other managers). The overlays contain a pointer to
the manager being used.
This patch makes the system a bit saner: each manager has a linked list
of overlays, and only the overlays linked to that manager are in the
list.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Overlay managers are stored in a linked list. There's no need for this
list, as an array would do just as fine.
This patch changes the code to use an array for overlay managers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Overlays are stored in a linked list. There's no need for this list, as
an array would do just as fine.
This patch changes the code to use an array for overlays.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dss_mgr_start_update() has a loop, of which sole purpose is to find the
manager used for this update. The whole loop is extra, as we already
know the manager.
Remove the loop.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There's no need to register the vsync ISR and configure the hardware if
the overlay manager is disabled, so this patch adds a check for disabled
managers to the omap_dss_mgr_apply() function.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The mechanism to cache manager and overlay settings and configure them
into the HW registers in VSYNC is meant only for auto-update displays,
as it doesn't make sense (and doesn't work) for manual-update displays.
This patchs adds a check so that we skip the above for manual update
displays.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add "enabled" field to struct omap_overlay_manager, which tells if the
output is enabled or not. This will be used in apply.c in the following
patches.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_overlay_manager struct contains enable() and disable() functions.
However, these are only meant to be used from inside omapdss, and thus
it's bad to expose the functions.
This patch adds dss_mgr_enable() and dss_mgr_disable() functions to
apply.c, which handle enabling and disabling the output.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Create a new file, apply.c, and move code about handling the
apply-mechanism and configuration of the managers and overlays from
manager.c to apply.c.
Not all related code is moved in this patch, but only the core
apply/configure functions. The later patches move rest of the code from
overlay.c and manager.c, adding necessary locking at the same time.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_dss_mgr_apply currently applies settings to all overlays and
overlay managers. The reason for this was to support cases where
configuration changes affecting multiple managers are made. However, the
current code doesn't support changing such configurations, so the
functionality is not needed.
Change the apply to affect only the manager given as an argument, and
the overlays attached to that manager.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add helper functions ovl_manual_update() and mgr_manual_update() which
return whether the overlay or manager is used with a manual update
display.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There's an unnecessary wrapper function, dss_ovl_wait_for_go(), which
does nothing else than call dss_mgr_wait_for_go_ovl(). The
dss_ovl_wait_for_go() function can be removed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Change manager configuration to be similar to overlay configuration by
creating dispc_mgr_setup() which takes omap_overlay_manager_info as
parameter.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Overlay channel is configured with ovl_setup, with all the other overlay
attriutes. This patch separates overlay channel setup so that we can
later configure the channel only when needed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Overlay FIFO thresholds are configured with ovl_setup, with all the
other overlay attributes. This patch separates FIFO threshold setup so
that we can later configure FIFO thresholds only when needed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move the configuration of interlace and replication from
omap_dss_mgr_apply() to configure_overlay(). This removes the need to
store the values into the cache data.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Overlay out_width/height are set to 0 when scaling is not used by the
users of omapdss. Currently ovl_setup() expects the caller of
ovl_setup() to convert those zero values to width or height.
This patch makes ovl_setup() accept zero values for out_width/height,
making calling ovl_setup() a bit simpler as the overlay_info can be
just passed to this function without modifications.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dss_start_update() takes currently the dss device as a parameter. Change
the parameter to ovl manager, as that is what the dss_start_update()
actually needs. Change the name of the function to
dss_mgr_start_update() to reflect the change.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Partial update for manual update displays has never worked quite well:
* The HW has limitations on the update area, and the x and width need to
be even.
* Showing a part of a scaled overlay causes artifacts.
* Makes the management of dispc very complex
Considering the above points and the fact that partial update is not
used anywhere, this and the following patches remove the partial update
support. This will greatly simplify the following re-write of the apply
mechanism to get proper locking and additional features like fifo-merge.
This patch removes the partial update from the panel-taal.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Partial update for manual update displays has never worked quite well:
* The HW has limitations on the update area, and the x and width need to
be even.
* Showing a part of a scaled overlay causes artifacts.
* Makes the management of dispc very complex
Considering the above points and the fact that partial update is not
used anywhere, this and the following patches remove the partial update
support. This will greatly simplify the following re-write of the apply
mechanism to get proper locking and additional features like fifo-merge.
This patch removes the partial update from the dsi.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Partial update for manual update displays has never worked quite well:
* The HW has limitations on the update area, and the x and width need to
be even.
* Showing a part of a scaled overlay causes artifacts.
* Makes the management of dispc very complex
Considering the above points and the fact that partial update is not
used anywhere, this and the following patches remove the partial update
support. This will greatly simplify the following re-write of the apply
mechanism to get proper locking and additional features like fifo-merge.
This patch removes the partial update from the manager.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Make dispc_ovl_set_fifo_threshold() public so that later patches can
handle overlay fifo configuration.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Make dispc_ovl_set_channel_out() public so that later patches can handle
changing overlay's manager.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Once in a time omapdss had basic support for fifomerge. Fifomerge was
removed as the implementation didn't work properly, and a proper
implementation is a complex problem.
However, some unused fifo-merge related code was left behind. This patch
removes those.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We sometimes get timeout when disabling the DSI interface with video
mode. It looks like the disable will stall until the current frame has
been finished, and this can take multiple milliseconds.
wait_for_bit_change() currently uses a busyloop to wait for a bit to
change. This is used in multiple places. The problem is, we don't have
clear understanding how long particular operations can take, so the
function needs to support longer waits.
Improve wait_for_bit_change() to first busy loop for 100 times to see if
the bit changes almost right away. If the bit hasn't changed, move to a
loop with a sleep of 1ms, and poll for 500ms.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The current code always enters ULPS for 3 lanes. This is not right, as
there could be only 2 lanes used, and on OMAP4 we have 5 lanes.
Fix the code to put all used lanes into ULPS.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There's no longer need for the dsi_get_num_lanes_used function, so it
can be removed. The lane check in dsi_init_display() can be removed as
the validity of the config will be verified when parsing it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the new lane config in dsi_cio_enable_lane_override(). The function
parameters are also slightly changed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the new lane config in dsi_cio_wait_tx_clk_esc_reset(). This also
extends the function to support 5 lanes on OMAP4, instead of 3 lanes.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Parse the lane configuration from the device data into internal lane
config format. This will be used in the following patches to clean up
the lane handling.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DSI driver currently counts used lanes and number of supported lanes by
using the number of data lanes (i.e. excluding clock lane). This patch
changes this to use the number of all lanes so that the following lane
config patches are cleaner.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Flush posted write in _enable_lcd_out() and _enable_digit_out(). This
ensures the the lcd/digit bit is written before the code starts waiting
for interrupts about enabling/disabling the output.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Flush posted write after setting the bit to send the BTA to ensure the
BTA is sent right away, as the code in dsi_vc_send_bta_sync() waits for
an interrupt caused indirectly by sending the BTA.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add data for the FocalTech ETM070003DH6 display to the generic_dpi_panel
display driver.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
A DRM display driver for TI OMAP platform. Similar to omapfb (fbdev)
and omap_vout (v4l2 display) drivers in the past, this driver uses the
DSS2 driver to access the display hardware, including support for
HDMI, DVI, and various types of LCD panels. And it implements GEM
support for buffer allocation (for KMS as well as offscreen buffers
used by the xf86-video-omap userspace xorg driver).
The driver maps CRTCs to overlays, encoders to overlay-managers, and
connectors to dssdev's. Note that this arrangement might change slightly
when support for drm_plane overlays is added.
For GEM support, non-scanout buffers are using the shmem backed pages
provided by GEM core (In drm_gem_object_init()). In the case of scanout
buffers, which need to be physically contiguous, those are allocated
with CMA and use drm_gem_private_object_init().
See userspace xorg driver:
git://github.com/robclark/xf86-video-omap.git
Refer to this link for CMA (Continuous Memory Allocator):
http://lkml.org/lkml/2011/8/19/302
Links to previous versions of the patch:
v1: http://lwn.net/Articles/458137/
v2: http://patches.linaro.org/4156/
v3: http://patches.linaro.org/4688/
v4: http://patches.linaro.org/4791/
History:
v5: move headers from include/drm at Greg KH's request, minor rebasing
on 3.2-rc1, pull in private copies of drm_gem_{get,put}_pages()
because "drm/gem: add functions to get/put pages" patch is not
merged yet
v4: bit of rework of encoder/connector _dpms() code, modeset_init()
rework to not use nested functions, update TODO.txt
v3: minor cleanups, improved error handling for dev_load(), some minor
API changes that will be needed later for tiled buffer support
v2: replace omap_vram with CMA for scanout buffer allocation, remove
unneeded functions, use dma_addr_t for physical addresses, error
handling cleanup, refactor attach/detach pages into common drm
functions, split non-userspace-facing API into omap_priv.h, remove
plugin API
v1: original
Signed-off-by: Rob Clark <rob@ti.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current code calculates scaling factors for video overlays even when the
overlays are not scaled. Change the code to skip calculations when not
scaling.
This optimizes the code a bit, but also fixes a problem when configuring
an overlay for a disabled display: if the display is disabled we don't
necessarily know the pixel clock used when the display is enabled, and
in some cases (like HDMI) the pixel clock is set to zero until a proper
video mode is set later. A wrong pixel clock will mess up the
scaling calculations, causing an error like:
omapdss DISPC error: failed to set up scaling, required fclk rate = 0
Hz, current fclk rate = 170666666 Hz
A proper fix would be to check later whether the clocks are enough for the
scaling, at the point when the overlay or display is actually enabled,
but this patch removes the problem for now.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
hdmi_get_pixel_clock() returns the pixel clock in Hz, but the pck is
stored as kHz. This means the return value has to be multiplied by 1000,
not by 10000 as the code did.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
They were getting this implicitly by an include of module.h
from device.h -- but we are going to clean that up and break
that include chain, so include module.h explicitly now.
[ with contributions from Axel Lin <axel.lin@gmail.com> ]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
With module.h being implicitly everywhere via device.h, the absence
of explicitly including something for EXPORT_SYMBOL went unnoticed.
Since we are heading to fix things up and clean module.h from the
device.h file, we need to explicitly include these files now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Compiling panel-picodlp.c failed with:
drivers/video/omap2/displays/panel-picodlp.c:560:12: error:
'THIS_MODULE' undeclared here (not in a function)
Add #include <linux/module.h> to get THIS_MODULE definition.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Since commit [e58aa3d2: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled
and we even check and yell when an interrupt handler
returns with interrupts enabled (see commit [b738a50a:
genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Add zorder support on OMAP4, this feature allows deciding the visibility order
of the overlays based on the zorder value provided as an overlay info parameter
or a sysfs attribute of the overlay object.
Use the overlay cap OMAP_DSS_OVL_CAP_ZORDER to determine whether zorder is
supported for the overlay or not. Use dss feature FEAT_ALPHA_FREE_ZORDER
if the caps are not available.
Ensure that all overlays that are enabled and connected to the same manager
have different zorders. Swapping zorders of 2 enabled overlays currently
requires disabling one of the overlays.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add support for VIDEO3 pipeline on OMAP4:
- Add VIDEO3 pipeline information in dss_features and omapdss.h
- Add VIDEO3 pipeline register coefficients in dispc.h
- Create a new overlay structure corresponding to VIDEO3.
- Make changes in dispc.c for VIDEO3
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
On OMAP3, in order to enable alpha blending for LCD and TV managers, we needed
to set LCDALPHABLENDERENABLE/TVALPHABLENDERENABLE bits in DISPC_CONFIG. On
OMAP4, alpha blending is always enabled by default, if the above bits are set,
we switch to an OMAP3 compatibility mode where the zorder values in the pipeline
attribute registers are ignored and a fixed priority is configured.
Rename the manager_info member "alpha_enabled" to "partial_alpha_enabled" for
more clarity. Introduce two dss_features FEAT_ALPHA_FIXED_ZORDER and
FEAT_ALPHA_FREE_ZORDER which represent OMAP3-alpha compatibility mode and OMAP4
alpha mode respectively. Introduce an overlay cap for ZORDER. The DSS2 user is
expected to check for the ZORDER cap, if an overlay doesn't have this cap, the
user is expected to set the parameter partial_alpha_enabled. If the overlay has
ZORDER cap, the DSS2 user can assume that alpha blending is already enabled.
Don't support OMAP3 compatibility mode for now. Trying to read/write to
alpha_blending_enabled sysfs attribute issues a warning for OMAP4 and does not
set the LCDALPHABLENDERENABLE/TVALPHABLENDERENABLE bits.
Change alpha_enabled to partial_alpha_enabled in the omap_vout driver. Use
overlay cap "OMAP_DSS_OVL_CAP_GLOBAL_ALPHA" to check if overlay supports alpha
blending or not. Replace this with checks for VIDEO1 pipeline.
Cc: linux-media@vger.kernel.org
Cc: Lajos Molnar <molnar@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Four of the LCD panel drivers depend on the backlight class,
so add the dependency in Kconfig.
Selecting the BACKLIGHT_CLASS_DEVICE symbol does not generally
work since it has other dependencies.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[tomi.valkeinen@ti.com: changed also N8x0 panel]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
overlay_info struct, used to configure overlays, currently includes both
physical and virtual addresses for the pixels. The vaddr was added to
support more exotic configurations where CPU would be used to update a
display, but it is not currently used and there has been no interest in
the feature. Using CPU to update a screen is also less interesting now
that OMAP4 has two LCD outputs.
This patch removes the vaddr field, and modifies the users of omapdss
accordingly. This makes the use of omapdss a bit simpler, as the user
doesn't need to think if it needs to give the vaddr.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add support to dump the HDMI wrapper, core, PLL and PHY registers
through debugfs.
Signed-off-by: Mythri P K <mythripk@ti.com>
[tomi.valkeinen@ti.com: updated the description]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add some of the missing register definitions, which are h/w indexable.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove usage of hdmi_reg struct to use u16 instead in the HDMI IP header
file. hdmi_reg struct is not really needed, and the same change was also
made for dispc earlier.
Signed-off-by: Mythri P K <mythripk@ti.com>
[tomi.valkeinen@ti.com: updated the description]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move the comments in AVI infoframe structure above each parameter
to align with other comments in the header file.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This is a driver for N800's display, ported from the old omapfb. This is
a slightly lighter version of the driver as not all features of the old
driver can be ported without big changes to DSS2, and also because some
of the HW features used in the old driver are unclear (e.g. the power
management part).
That said, the new driver works fine for basic use.
Architecturally the driver is not as neat as it could be. N800's display
HW consists of a display buffer chip and a panel, and ideally they would
be represented by separate, independent drivers. This is not currently
possible, and this driver contains both buffer chip and panel driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Port the old omapfb panel driver for Apollon to DSS2.
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Taal panel driver supports two kinds of backlight control: 1) using DSI
commands sent to the panel to control the backlight, 2) calling function
pointers going to the board file to control the backlight.
The second option is a bit hacky, and will no longer be needed when the
PWM driver supports the backlight features. After that we can use the
standard PWM backlight driver.
This patch removes the second backlight control mechanism, and adds a
boolean field, use_dsi_backlight, to nokia_dsi_panel_data which the
board file can use to inform whether the panel driver should use DSI
commands to control the backlight.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Create a dss_range_param member called FEAT_PARAM_DOWNSCALE to get the maximum
downscaling possible on the current platform. Use this in
dispc_ovl_calc_scaling().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move DISPC scaling related code from dispc_ovl_setup() to a new function
dispc_ovl_calc_scaling(). Use overlay caps to check if the overlay can scale or
not. No functional changes are made.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The function calc_fclk_five_taps() uses a fixed value of pixels per line which
is used in calculations to get the minimum fclk needed for scaling with five
taps to work.
Remove this by providing the width of the panel connected to the manager.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dispc_mgr_pclk_rate() is used to calculate minimum required functional clock for
scaling in calc_fclk() and calc_fclk_five_taps(). This function returns the
correct pixel clock for LCD and LCD2 managers, but not for TV manager. Extend
this function so that it gets the correct pixel clock for TV manager.
This also prevents the crash we get when we try to scale overlays connected to
TV manager. The current code leads to a BUG() being executed if we call
dispc_mgr_pclk_rate() for the TV manager.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Create a helper function called dispc_mgr_is_lcd() which returns true if the
manager is LCD or LCD2.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dispc_ovl_enable_replication() and dispc_ovl_set_fifo_threshold() are currently
called in configure_overlay(). These are the only functions which cause DISPC
register writes of overlay parameters outside of dispc_ovl_setup().
Move these to dispc_ovl_setup() and pass replication, fifo_low and fifo_high
thresholds as arguments to dispc_ovl_setup() in order to be aligned with other
overlay parameters. No functional changes are made.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dispc_ovl_setup() currently takes a large number of overlay arguments, most of
these are members of the overlay_info struct. Replace these arguments by
passing a overlay_info pointer instead.
In configure_overlay(), we create an overlay_info struct called new_oi, this is
a copy of the overlay cache's overlay_info member. Update the new_oi parameters
which could have been possibly changed in configure_overlay(). Pass its pointer
pointer to dispc_ovl_setup().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the new read_edid() function to get EDID information from the
display (when available), and use the information to use a suitable mode
at initialization time.
Hot-plug is not yet supported, so the timings selected at init time will
stay even if the monitor would be changed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We have currently panel-generic-dpi driver, which is a combined driver
for dummy panels and also for DVI output.
The aim is to split the panel-generic-dpi into two, one for fixed size
dummy panels connected via DPI, and the other (this) for variable
resolution output which supports DDC channel (in practice a DVI framer
chip connected to DPI output).
Original i2c code by: Ricardo Salveti de Araujo
<ricardo.salveti@canonical.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Implement detect() by checking the hot plug detect status.
The implementation is not very good, as it always turns on the HDMI
output to get the detection working. HDMI driver needs improvements so
that we could enable only core parts of it.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
check_timings() is supposed to be used to verify if timings are ok or
not. Currently the HDMI driver prints error messages if the timings are
not ok. This is not right, as it is no error to give invalid timings to
check_timings().
Remove the error prints.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Clean up reading of EDID by passing direct address to the block being
read, instead of start address of the whole EDID memory area. Rewrite
the loop which reads the EDID.
This also fixes the checksum calculation, which used to calculate the
checksum only for the first block.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Split the DDC initialization off from hdmi_core_ddc_edid() into a
separate function hdmi_core_ddc_init(). This cleans up the
implementation.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAPFB handles EDID parsing now, using the common helper functions in
fbdev. We can remove the EDID parsing from HDMI driver.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Implement read_edid() for HDMI by implementing necessary functions to
hdmi.c and to hdmi_omap4_panel.c.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently the set_timings code for hdmi is quite strange. The display is
disabled in hdmi_omap4_panel.c before setting timings, and enabled in
hdmi.c after setting the timings. Furthermore, the timings were not
permanent, and disabling and enabling the display would lose them.
This patch makes the set_timings handling a bit better.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Enabling HDMI output often causes sync lost errors, and almost always
causes timeout errors being printed from dispc_mgr_enable_digit_out().
The sync lost problem seems to go lessen greatly if we first enable the
HDMI output, and only then enable the DISPC output. However, as this is
only based on observations, the fix may not be perfect as the problem
may lie somewhere else. Nevertheless, HDMI works better with this patch.
This will also fix the dispc's dispc_mgr_enable_digit_out(), as the code
waits for two VSYNCs after enabling the output. If the HDMI output is
disabled (as it was previously), there are no VSYNCs and
dispc_mgr_enable_digit_out() will print timeout errors.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dispc_mgr_enable_digit_out() didn't handle HDMI case very well.
Improve the function to use FRAMEDONETV interrupt to see when HDMI has
been disabled.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add dss_get_hdmi_venc_clk_source(), which can be used to get the value
programmed with dss_select_hdmi_venc_clk_source(). This can be used to
find out if the digit output is going to VENC or HDMI.
For OMAP2/3 dss_get_hdmi_venc_clk_source() always returns
DSS_VENC_TV_CLK.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
regn divider is currently programmed to the registers without change,
but when calculating clock frequencies it is used as regn+1.
To make this similar to how DSI handles the dividers this patch changes
the regn value to be used as such for calculations, but the value
programmed to registers is regn-1.
This simplifies the clock frequency calculations, makes it similar to
DSI, and also allows us to use regn value 0 as undefined.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use default regn and regm2 dividers in the hdmi driver if the board file
does not define them.
Cc: Mythri P K <mythripk@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The current driver had a hardcoded minimum value of 2 for pixel clock
divisor (PCD). This doesn't seem to be right.
OMAP4 TRM says that PCD can be 1 when not downscaling, and inverted
pixel clock (IPC) is off.
OMAP3 TRM says the same, but also in the register descriptions that PCD
value 1 is invalid.
OMAP2 TRM says PCD 2 is the minimum.
OMAP2 is still untested, but for both OMAP3 and OMAP4 PCD of 1 seems to
work fine.
This patch adds a new DSS feature, FEAT_PARAM_DSS_PCD, which is used to
find the minimum and maximum PCD. The minimum is set to 2 for OMAP2, and
1 for OMAP3/4.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
As the panel driver will remain generic across OMAP's renaming it to
hdmi_panel.c
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
HDMI IP fundamentally has replaceable core PHY and PLL blocks.
These blocks might vary across OMAP's but the end functionality such as to
enable or disable PLL, PHY, function to read EDID would remain the same.
Thus to make the current hdmi DSS driver compatible with different OMAP's having
different IP blocks( A combination of different core, PHY, PLL blocks), function
pointer approach is introduced.
With function pointer, relevant IP dependent functions are mapped to the generic
functions used by DSS during the initialization based on the OMAP compiled.
Thus making hdmi DSS driver IP agnostic.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Functions that are included in HDMI IP driver is renamed to have
IP specific names so that it will not conflict with similar functions
from other IP.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move HDMI IP dependent audio functions from HDMI DSS file to IP library.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Split the current HDMI driver to move the HDMI IP dependent ( PLL/PHY/Core
configuration code) to a new IP file (ti_hdmi_4xxx_ip.c.
This is to separate IP dependent OMAP agnostic code from OMAP specific DSS
dependent code.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Clean up to move the EDID definition from the IP dependent header file to hdmi.c
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Some of the header file definitions that are there in the hdmi.h are generic
and can be used across OMAP's, Thus moving generic definition to new file.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
As hdmi has few additional parameters such as vsync and hsync
polarity which is missing in DSS timing structure, define HDMI timings
structure for hdmi to use instead of OMAP DSS timing structure.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
As the pll and the video configuration info are part of the ip_data, pll
and video structures are moved to the ip_data structure. Also the pll and
video configuration functions are modified accordingly to take care of the
structure movement.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
As the base_address of the HDMI might differ across SoC's, offset of the HDMI
logical blocks(PHY, PLL and Core) and base address procured from the platform
data are passed dynamically to the functions that modify HDMI IP registers.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add initial support for DSI video mode panels:
- Add a new structure omap_dss_dsi_videomode_data in the member "panel" in
omap_dss_device struct. This allows panel driver to configure dsi video_mode
specific parameters.
- Configure basic DSI video mode timing parameters: HBP, HFP, HSA, VBP, VFP, VSA,
TL and VACT.
- Configure DSI protocol engine registers for video_mode support.
- Introduce functions dsi_video_mode_enable() and dsi_video_mode_disable() which
enable/disable video mode for a given virtual channel and a given pixel format
type.
Things left for later
- Add functions to check for errors in video mode timings provided by panel.
- Configure timing registers required for command mode interleaving.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dsi_vc_send_null() currently sends a long packet with data type
MIPI_DSI_NULL_PACKET and packet length 4. Modify it to send a zero
length long packet. This leads to sending only the long packet header
and no payload packets and hence the transfer completes faster.
The function can be modified later if there is a need to send null
packets of a non-zero length.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently, DSI pixel info is only represented by the pixel size in bits using
the pixel_size parameter in omap_dss_device struct's ctrl member.
This is not sufficient information for DSI video mode usage, as two of the
supported formats(RGB666 loosely packed, and RGB888) have the same pixel
container size, but different data_type values for the video mode packet header.
Create enum "omap_dss_dsi_pixel_format" which describes the pixel data format
the panel is configured for. Create helper function dsi_get_pixel_size() which
returns the pixel size of the given pixel format.
Modify functions omapdss_default_get_recommended_bpp() and dss_use_replication()
to use dsi_get_pixel_size().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Split the function dispc_set_parallel_interface_mode() into 2 separate
functions called dispc_mgr_set_io_pad_mode() and dispc_mgr_enable_stallmode().
The current function tries to set 2 different modes(io pad mode and stall mode)
based on a parameter omap_parallel_interface_mode which loosely corresponds to
the panel interface type.
This isn't correct because a) these 2 modes are independent to some extent,
b) we are currently configuring gpout0/gpout1 for DSI panels which is
unnecessary, c) a DSI Video mode panel won't get configured correctly.
Splitting the functions allows the interface driver to set these modes
independently and hence allow more flexibility.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Introduce read functions which use generic Processor-to-Peripheral
transaction types. These are needed by some devices which may not support
corresponding DCS commands.
Add function dsi_vc_generic_send_read_request() which can send
a short packet with 0, 1 or 2 bytes of request data and the corresponding
generic data type.
Rename function dsi_vc_dcs_read_rx_fifo() to dsi_vc_read_rx_fifo() and modify
it to take the enum "dss_dsi_content_type" as an argument to use either DCS
or GENERIC Peripheral-to-Processor transaction types while parsing data read
from the device.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Split dsi_vc_dcs_read() into the functions:
- dsi_vc_dcs_send_read_request(): This is responsible for sending the short
packet command with the read request.
- dsi_vc_dcs_read_rx_fifo(): This parses the DSI RX fifo of the given virtual
channel, identifies the type of data received, and fills a buffer with the data
provided by the panel.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove functions dsi_vc_dcs_read_1() and dsi_vc_dcs_read_2(), these are used
when the panel is expected to return 1 and 2 bytes respecitvely. This was manily
used for debugging purposes. These functions should be implemented in the panel
driver if needed.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Intoduce enum "dss_dsi_content_type" to differentiate between DCS and generic
content types.
Introduce short and long packet write functions which use generic
Processor-to-Peripheral transaction types. These are needed by some devices
which may not support corresponding DCS commands. Create common write functions
which allow code reuse between DCS and generic write functions.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Create an enum for DSI operation modes, use this to set the capabilities of the
device in dsi_init_display().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The enum type dsi_vc_mode is a bit misleading as L4 slave port and video port
are sources to VC rather than the mode of operation. Rename then enum type and
its members. Merge dsi_vc_config_vp() and dsi_vc_config_l4() into a single
function called dsi_vc_config_source() which takes dsi_vc_source enum as an
extra argument.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
MIPI DSI Transaction types and DCS commands are currently defined as
macros in dsi.c and panel-taal.c, remove these and replace them with
enum members defined in include/video/mipi_display.h.
Signed-off-by: Archit Taneja <archit@ti.com>
[tomi.valkeinen@ti.com: reformatted the commit message]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add support for Innolux AT070TN83, a 7 inch LCD
with RGB-Interface and touch panel to panel-generic-dpi.
Tested with Devkit8000.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Rename dispc's manager related functions as follows:
- Remove prepending underscores, which were originally used to inform
that the clocks needs to be enabled. This meaning is no longer valid.
- Prepend the functions with dispc_mgr_*
- Remove "channel" from the name, e.g. dispc_enable_channel ->
dispc_mgr_enable
The idea is to group manager related functions so that it can be deduced
from the function name that it writes to manager spesific registers.
All dispc_mgr_* functions have enum omap_channel as the first parameter.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Rename dispc's overlay related functions as follows:
- Remove prepending underscores, which were originally used to inform
that the clocks needs to be enabled. This meaning is no longer valid.
- Prepend the functions with dispc_ovl_*
- Remove "plane" from the name, e.g. dispc_set_plane_ba0 ->
dispc_ovl_set_ba0
The idea is to group overlay related functions so that it can be deduced
from the function name that it writes to overlay spesific registers.
All dispc_ovl_* functions have enum omap_plane as the first parameter.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add OMAP_DSS_OVL_CAP_GLOBAL_ALPHA and OMAP_DSS_OVL_CAP_PRE_MULT_ALPHA to
overlay capabilities. Use these instead of FEAT_GLOBAL_ALPHA,
FEAT_GLOBAL_ALPHA_VID1 and FEAT_PRE_MULT_ALPHA in code.
Remove FEAT_GLOBAL_ALPHA_VID1 and FEAT_PRE_MULT_ALPHA which are no
longer used. FEAT_GLOBAL_ALPHA is still used to decide if the HW has
global alpha register.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Archit Taneja <archit@ti.com>
Add support to define overlay capabilities into dss_features. The
features are set to overlay->caps at initialization time.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Archit Taneja <archit@ti.com>
Use lookup tables instead of switch/if in some DISPC functions to make
the code cleaner.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Archit Taneja <archit@ti.com>
Remove support for non-DISPC overlays and overlay managers.
The support to possibly have non-DISPC overlays and managers was made to
make it possible to use CPU and/or sDMA to update RFBI or DSI command
mode displays. It is ok to remove the support, because:
- No one has used the feature.
- Display update without DISPC is very slow, so it is debatable if the
update would even be usable.
- Removal cleans up code.
- If such a feature is needed later, it is better implemented outside
omapdss driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Archit Taneja <archit@ti.com>
DSS driver has not been "experimental" for many years now, so perhaps
it's time to remove the text from Kconfig titles.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently when changing the manager of an overlay, set_manager() directly
calls dispc to set the overlay's destination.
Change this to be more in line with other overlay configurations, and
this will also remove the need to have dispc clocks enabled when calling
set_manager().
A new field is added to overlay struct, "manager_changed". This is
similar to "display_changed" field in manager struct, and is used to
inform apply that the manager has changed and thus write to the
registers is needed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DPI and DSI were not cleaning up the clock source in error or uninit
cases. Set the clock source back to PRCM.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently omapfb wants that all the display devices have a driver,
otherwise omapfb refuses to start. There's no real requirement to act
like that, and this patch will make omapfb give a warning and skip that
device.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dsi_mux_pads() needs to know about the DSI HW module and the DSI lanes
used. Split the function into two, enable and disable, which take
necessary arguments, and add empty implementations for both.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently, there are 2 differently named platform devices generated for
the 2 DSS DSI modules. In order to use the same driver, the dsi devices
should be 2 instances of the same platform device.
Change the platform device names from "omapdss_dsi1" and "omapdss_dsi2"
to omapdss_dsi", and set the device indices to 0 and 1.
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that the HWMOD fmwk handles the fcks of DSS modules properly, the
DSS driver no longer needs to explicitely enable/disable the fck.
This patch removes the enables/disables of fck from dispc, dsi and dss.
The clk_get(fck) is still needed there, as the modules need to know the
frequency of the clock.
For hdmi and venc this patch also removes the clk_get(fck), as they
don't need the clock at all.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The array size of fifo_size array in the global dispc struct is currently
hardcoded to 3. Replace this with the MAX_DSS_OVERLAYS macro in dss_features.h,
use dss_features function to get the number of overlays instead of the
ARRAY_SIZE macro in dispc_read_plane_fifo_sizes().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Iterate over overlay id's to shorten _dispc_set_color_conv_coef()
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Iterate over manager and overlay id's to shorten dispc_save_context() and
dispc_restore_context().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Iterate over manager and overlay id's to shorten dispc_dump_regs().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Prepare dispc_dump_regs() to iterate over manager and overlay id's. Doing this
requires modifications of the macro "DUMPREG" which currently needs us to specify
the manager/overlay name to get the correct result. For example, in order to
print the register DISPC_TIMING_H(OMAP_DSS_CHANNEL_LCD), we can't iterate over
a varaible i and get the desired result through DUMPREG(DISPC_TIMING_H(i)).
Split the registers into 3 sections, the first with no arguments(common
registers), the second with one argument(manager/overlay id), and the third with
two arguments(overlay id and coefficient index), redefine DUMPREG macros for
each of these.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Make the debug message useful by printing the name of the device
that no associated driver could be found for.
Signed-off-by: Andy Doan <andy.doan@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There's no guarantee that the error handler worker thread
will run while the dispc clocks are on. Explicitly enable/disable
them.
Signed-off-by: Dima Zavin <dima@android.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If a manager is moved while attached to an enabled display, the DSS
system will be left in an inconsistent state. This will eventually cause
a kernel oops when the enabled display is disabled.
Fix this by not allowing the user to move a manager away from an enabled
display.
Signed-off-by: Daniel Morsing <daniel.morsing@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
None of the DSS interface drivers check if an overlay manager is
connected to the display when the display is being enabled. This leads
to null pointer crash if the display has no manager.
This patch checks for the manager and returns an error if it is null.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fix two problems in PicoDLP driver's error handling on
picodlp_panel_power_on:
- If omapdss_dpi_display_enable() failed, the its error value was not
returned
- If picodlp_i2c_init() failed, dssdev->state was erroneously set to
OMAP_DSS_DISPLAY_ACTIVE
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
PicoDLP is a micro projector from TI.
DLP used in OMAP4 is dpp2600 (DLP Pico Projector) The DLP requires
commands to be sent over i2c for configurations. To know more about
dpp2600 commands please visit:
https://focus.ti.com/myti/docs/extranet.tsp?sectionId=403
The picodlp module consists of a dss driver and an i2c_client.
To know more please visit:
http://www.omappedia.org/wiki/PicoDLP_projector_guide
Based on original design from Mythri P K <mythripk@ti.com>
Signed-off-by: Mayuresh Janorkar <mayur@ti.com>
Signed-off-by: Mythri P K <mythripk@ti.com>
[tomi.valkeinen@ti.com: squashed commits]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Ricardo Neri