The current practice is to not add _clk suffixes to clock node names in
DT, as these names are used as the actual clock names.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add properties to describe the reset topology for on-SoC devices:
- Add the "#reset-cells" property to the CPG/MSSR device node,
- Add resets and reset-names properties to the various device nodes.
This allows to reset SoC devices using the Reset Controller API.
Note that all resets added match the corresponding module clocks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add properties to describe the reset topology for on-SoC devices:
- Add the "#reset-cells" property to the CPG/MSSR device node,
- Add resets and reset-names properties to the various device nodes.
This allows to reset SoC devices using the Reset Controller API.
Note that all resets added match the corresponding module clocks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update the r8a7795 SATA device node to use a 2MiB I/O space as specified
in the "72. Serial-ATA" section of R-Car-Gen3-rev0.52E.pdf
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk device node is already enabled in r8a7796.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk device node is already enabled in r8a7796.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk and pcie_bus_clk device nodes are already enabled in
r8a7795.dtsi, so there is no need to update their statuses again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk device node is already enabled in r8a7795.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the performance monitor unit for the Cortex-A53 cores on the
R8A7796 SoC.
Extracted from a patch by Takeshi Kihara in the BSP.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds Cortex-A53 CPU cores of R8A7796 SoC, and sets a total of
6 cores (2 x Cortex-A57 + 4 x Cortex-A53).
Based on a patch by Takeshi Kihara in the BSP.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Cortex-A53 L2 cache-controller.
The L2 cache for the Cortex-A53 CPU cores is 512 KiB large (organized as
32 KiB x 16 ways).
Extracted from a patch by Takeshi Kihara in the BSP.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the performance monitor unit for the Cortex-A57 cores on the
R8A7796 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds Cortex-A57 CPU cores to R8A7796 SoC for a total of
2 x Cortex-A57.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Rebased]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current Audio-DMAC is assigned "rx" as Audio-DMAC0, "tx" as Audio-DMAC1.
Thus, DVC "tx" should be assigned as Audio-DMAC1, instead of Audio-DMAC0.
Because of this, current platform board (using SRC/DVC/SSI)
Playback/Capture both will use same Audio-DMAC0
(but it depends on audio data path).
First note is that this "rx" and "tx" are from each IP point,
it doesn't mean Playback/Capture.
Second note is that Audio DMAC assigned on DT is only for
Audio-DMAC, Audio-DMAC-peri-peri has no entry.
=> Audio-DMAC
-> Audio-DMAC-peri-peri
-- HW connection
Playback case
[Mem] => [SRC]--[DVC] -> [SSI]--[Codec]
rx ~~~~~~~~~~~~
Capture
[Mem] <= [DVC]--[SRC] <- [SSI]--[Codec]
tx ~~~~~~~~~~~~
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The EthernetAVB should not depend on the bootloader to setup correct
drive-strength values. Values for drive-strength where found by
examining the registers after the bootloader has configured the
registers and successfully used the EthernetAVB.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Cortex-A57 cache controller is an integrated controller, and thus
the device node representing it should not have a unit-addresses or reg
property.
Fixes: 1561f20760 ("arm64: dts: r8a7796: Add Renesas R8A7796 SoC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Cortex-A57/A53 cache controllers are integrated controllers, and
thus the device nodes representing them should not have unit-addresses
or reg properties.
Fixes: 6f7bf82cc9 ("arm64: dts: r8a7795: Fix W=1 dtc warnings")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
>From PSCI v1.0, Suspend-to-RAM is supported via SYSTEM_SUSPEND PSCI
function call. Hence, upgrade PSCI version for R-Car M3-W to support
Suspend-to-RAM.
The Suspend-to-RAM is highly dependent on ARM Trusted Firwmare support
since necessary callback functions will be registered after a query
to ARM Trusted Firmware about SYSTEM_SUSPEND support.
Since PSCI v1.0 is backward compatible with PSCI v0.2, CPU Hotplug and
CPUIdle should be able to work normally with this change.
Signed-off-by: Khiem Nguyen <khiem.nguyen.xt@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Keep "arm,psci-0.2"]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
>From PSCI v1.0, Suspend-to-RAM is supported via SYSTEM_SUSPEND PSCI
function call. Hence, upgrade PSCI version for R-Car H3 to support
Suspend-to-RAM.
The Suspend-to-RAM is highly dependent on ARM Trusted Firwmare support
since necessary callback functions will be registered after a query
to ARM Trusted Firmware about SYSTEM_SUSPEND support.
Since PSCI v1.0 is backward compatible with PSCI v0.2, CPU Hotplug and
CPUIdle should be able to work normally with this change.
Signed-off-by: Khiem Nguyen <khiem.nguyen.xt@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Keep "arm,psci-0.2"]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the performance monitor unit for the Cortex-A53 cores on the
R8A7795 SoC.
Extracted from a patch by Takeshi Kihara in the BSP.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds Cortex-A53 CPU cores to r8a7795 SoC for a total of 8
cores (4 x Cortex-A57 + 4 x Cortex-A53).
Based on work by Takeshi Kihara and Dirk Behme.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enables the SCIF hooked up to the DEBUG1 connector.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device nodes for all R-Car H3 SCIF serial ports, incl. clocks
and power domain.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device nodes for all HSCIF serial ports, incl. clocks, and
power domain.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: express register size in hex; refer to power domain in changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Set PHY rxc-skew-ps to 1500 and all other values to their default values.
This is intended to to address failures in the case of 1Gbps communication
using the by salvator-x board with the KSZ9031RNX phy. This has been
reported to occur with both the r8a7795 (H3) and r8a7796 (M3-W) SoCs.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since commit 61fccb2d62 ("ravb: Add tx and rx clock internal delays mode
of APSR") the EthernetAVB driver enables tx and rx clock internal delay
modes (TDM and RDM) depending on the phy mode as follows:
phy mode | ASPR delay mode
-----------+----------------
rgmii-id | TDM and RDM
rgmii-rxid | RDM
rgmii-txid | TDM
And prior to the above commit no internal delay mode settings were
implemented for any phy mode.
With this and the above change present tx internal delay mode is enabled
which has been observed to address failures in the case of 1Gbps
communication using the by salvator-x board with the KSZ9031RNX phy. This
has been reported to occur with both the r8a7795 (H3) and r8a7796 (M3-W)
SoCs.
With the above patch present but this patch present tx and rx internal
delay modes are enabled; and with the above patch and this present absent
no internal delay modes are enabled. In both cases failures have been
observed when using 1Gbps communication in the environments described
above.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Set PHY rxc-skew-ps to 1500 and all other values to their default values.
This is intended to to address failures in the case of 1Gbps communication
using the by h3ulcb board with the KSZ9031RNX phy.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Set PHY rxc-skew-ps to 1500 and all other values to their default values.
This is intended to to address failures in the case of 1Gbps communication
using the by salvator-x board with the KSZ9031RNX phy. This has been
reported to occur with both the r8a7795 (H3) and r8a7796 (M3-W) SoCs.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since commit 61fccb2d62 ("ravb: Add tx and rx clock internal delays mode
of APSR") the EthernetAVB driver enables tx and rx clock internal delay
modes (TDM and RDM) depending on the phy mode as follows:
phy mode | ASPR delay mode
-----------+----------------
rgmii-id | TDM and RDM
rgmii-rxid | RDM
rgmii-txid | TDM
And prior to the above commit no internal delay mode settings were
implemented for any phy mode.
With this and the above change present tx internal delay mode is enabled
which has been observed to address failures in the case of 1Gbps
communication using the by salvator-x board with the KSZ9031RNX phy. This
has been reported to occur with both the r8a7795 (H3) and r8a7796 (M3-W)
SoCs.
With the above patch present but this patch present tx and rx internal
delay modes are enabled; and with the above patch and this present absent
no internal delay modes are enabled. In both cases failures have been
observed when using 1Gbps communication in the environments described
above.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables I2C for DVFS device for for Salvator-X board on
R8A7795 SoC.
Signed-off-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds support of I2C for DVFS device for Salvator-X board on
R8A7796 SoC.
Signed-off-by: Dien Pham <dien.pham.ry@rvc.renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
r8a779[56] SoCs:
* Mark EthernetAVB device node disabled in DT for r8a779[56] SoCs
- They are enabled as appropriate in board DT files
* Link ARM GIC to clock and clock domain on r8a779[56] SoCs
* Add thermal support
r8a7795 SoC:
* Tidyup audma definition order on r8a7795 SoC
* Add missing power-domains property for SATA
r8a7795/h3ulcb board:
* Add MIX/CTU support as per support present in DT for r8a7796
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=KG8o
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm64-dt2-for-v4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt64
Second Round of Renesas ARM64 Based SoC DT Updates for v4.11
r8a779[56] SoCs:
* Mark EthernetAVB device node disabled in DT for r8a779[56] SoCs
- They are enabled as appropriate in board DT files
* Link ARM GIC to clock and clock domain on r8a779[56] SoCs
* Add thermal support
r8a7795 SoC:
* Tidyup audma definition order on r8a7795 SoC
* Add missing power-domains property for SATA
r8a7795/h3ulcb board:
* Add MIX/CTU support as per support present in DT for r8a7796
* tag 'renesas-arm64-dt2-for-v4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: r8a7796: Mark EthernetAVB device node disabled
arm64: dts: r8a7795: Mark EthernetAVB device node disabled
arm64: dts: r8a7795: tidyup audma definition order
arm64: dts: r8a7796: Link ARM GIC to clock and clock domain
arm64: dts: r8a7795: Link ARM GIC to clock and clock domain
arm64: dts: r8a7796: Add R-Car Gen3 thermal support
arm64: dts: r8a7795: Add R-Car Gen3 thermal support
arm64: dts: r8a7795: Add missing power-domains property for sata
arm64: dts: h3ulcb: follow sound CTU/MIX supports
Signed-off-by: Olof Johansson <olof@lixom.net>
Device nodes representing I/O devices should be marked disabled in the
SoC-specific DTS, and overridden by board-specific DTSes where needed.
Fixes: 8e8b9eaef8 ("arm64: dts: renesas: r8a7796: Add EthernetAVB instance")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Device nodes representing I/O devices should be marked disabled in the
SoC-specific DTS, and overridden by board-specific DTSes where needed.
Fixes: a92843c8a6 ("arm64: dts: r8a7795: add EthernetAVB device node")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current r8a7795.dtsi defines audma -> ipmmu -> dma order.
Because of this order, dma can connect to ipmmu, but
audma can't connect to it.
This patch moves audma order as ipmmu -> dma -> audma.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-AP module clock, and add it to the SYSC
"always-on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-AP module clock, and add it to the SYSC
"always-on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This went unnoticed as the sata_rcar driver doesn't support Runtime PM
yet, but manages module clocks manually.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Add PWM, and sound MIX and CTU support to r8a7795 SoC
* Add CAN, CAN FD and all MSIOF nodes to r8a7796 SoC
* Use Gen 3 fallback binding for i2c, msiof, PCIE and USB2 phy
* Enable Ethernet and 4 GiB memory on r8a7796/salvator-x board
* Add r8a7796/salvator-x board part number to bindings
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=s00S
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm64-dt-for-v4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt64
Renesas ARM64 Based SoC DT Updates for v4.11
* Add PWM, and sound MIX and CTU support to r8a7795 SoC
* Add CAN, CAN FD and all MSIOF nodes to r8a7796 SoC
* Use Gen 3 fallback binding for i2c, msiof, PCIE and USB2 phy
* Enable Ethernet and 4 GiB memory on r8a7796/salvator-x board
* Add r8a7796/salvator-x board part number to bindings
* tag 'renesas-arm64-dt-for-v4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: r8a7795: Add PWM support
arm64: dts: r8a7796: Use R-Car Gen 3 fallback binding for msiof nodes
arm64: dts: r8a7796: salvator-x: Enable EthernetAVB
arm64: dts: renesas: r8a7796: Add EthernetAVB instance
arm64: dts: r8a7796: salvator-x: Update memory node to 4 GiB map
arm64: dts: r8a7796: Use R-Car Gen 3 fallback binding for i2c nodes
arm64: dts: r8a7795: Use R-Car Gen 3 fallback binding for i2c nodes
arm64: dts: r8a7795: Use Gen 3 fallback compat string for PCIE
arm64: dts: r8a7795: add sound MIX support
arm64: dts: r8a7795: add sound CTU support
arm64: dts: r8a7795: Use renesas,rcar-gen3-usb2-phy fallback binding
arm64: renesas: r8a7796/salvator-x: Add board part number to DT bindings
arm64: dts: r8a7796: Add CAN FD support
arm64: dts: r8a7796: Add CAN support
arm64: dts: r8a7796: Add CAN external clock support
arm64: dts: r8a7796: Add all MSIOF nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
* Provide sd0_uhs node
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XZkS
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Renesas ARM Based SoC Fixes for v4.10
* Provide sd0_uhs node
* tag 'renesas-fixes-for-v4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: h3ulcb: Provide sd0_uhs node
Add the 7 PWM channels to the r8a7795 device tree, in the disabled
state.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use recently added R-Car Gen 3 fallback binding for msiof nodes in
DT for r8a7796 SoC.
This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7796 and the
fallback binding for R-Car Gen 3.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Geert Uytterhoeven