Add stanza for cxlflash SCSI driver.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Following an adapter reset, the AFU RRQ that resides in host memory
holds stale data. This can lead to a condition where the RRQ interrupt
handler tries to process stale entries and/or endlessly loops due to an
out of sync generation bit.
To fix, the AFU RRQ in host memory needs to be cleared after each reset.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
There are several spelling and grammar mistakes throughout the
driver. Additionally there are a handful of places where there
are extra lines and unnecessary variables/statements. These are
a nuisance and pollute the driver.
Fix spelling and grammar issues. Update some comments for clarity and
consistency. Remove extra lines and a few unneeded variables/statements.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The process_sense() routine can perform a read capacity which
can take some time to complete. If an EEH occurs while waiting
on the read capacity, the EEH handler will wait to obtain the
context's mutex in order to put the context in an error state.
The EEH handler will sit and wait until the context is free,
but this wait can potentially last forever (deadlock) if the
scsi_execute() that performs the read capacity experiences a
timeout and calls into the reset callback. When that occurs,
the reset callback sees that the device is already being reset
and waits for the reset to complete. This leaves two threads
waiting on the other.
To address this issue, make the context unavailable to new,
non-system owned threads and release the context while calling
into process_sense(). After returning from process_sense() the
context mutex is reacquired and the context is made available
again. The context can be safely moved to the error state if
needed during the unavailable window as no other threads will
hold its reference.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Sparse uncovered several errors with MMIO operations (accessing
directly) and handling endianness. These can cause issues when
running in different environments.
Introduce __iomem and proper endianness tags/swaps where
appropriate to make driver sparse clean.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Several function prologs have incorrect parameter names and return
code descriptions. This can lead to confusion when reviewing the
source and creates inaccurate documentation.
To remedy, update the function prologs to properly reflect parameter
names and return codes.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The host reset handler is called with I/O already blocked, thus
there is no need to explicitly block and unblock I/O in the handler.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
When the device reset handler is entered while a reset operation
is taking place, the handler exits without actually sending a
reset (TMF) to the targeted device. This behavior is incorrect
as the device is not reset. Further complicating matters is the
fact that a success is returned even when the TMF was not sent.
To fix, the state is rechecked after coming out of the reset
state. When the state is normal, a TMF will be sent out.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The workq can process work in parallel with a remove event, leading
to a condition where the workq handler can access freed memory.
To remedy, the workq should be terminated prior to freeing memory. Move
the termination call earlier in remove and use cancel_work_sync() instead
of flush_work() as there is not a need to process any scheduled work when
shutting down.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Currently, scsi_host_put() is being called prematurely in the
remove path and is missing entirely in an error cleanup path.
The former can lead to memory being freed too early with
subsequent access potentially corrupting data whilst the former
would result in a memory leak.
Move the usage on remove to be the last cleanup action taken
and introduce a call to scsi_host_put() in the one initialization
error path that does not use remove to cleanup.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The AFU version is stored as a non-terminated string of bytes within
a 64-bit little-endian register. Presently the value is read directly
(no MMIO accessor) and is stored in a buffer that is not big enough
to contain a NULL terminator. Additionally the version obtained is not
evaluated against a known value to prevent usage with unsupported AFUs.
All of these deficiencies can lead to a variety of problems.
To remedy, use the correct MMIO accessor to read the version value into
a null-terminated buffer and add a check to prevent an incompatible AFU
from being used with this driver.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
At present, both ports must be online for the device to
configure properly. Remove this dependency and the unnecessary
internal LUN override logic as well. Additionally, as a refactoring
measure, change the return code variable name to match that used
throughout the driver.
With this change, the card will be able to configure even when the
link is down. At some later point when the link is transitioned to
'up', a link state change interrupt will trigger the port configuration.
Note that despite its void-like behavior, the function was left with a
return code for right now in case its behavior needs to be altered again
in the near future based on testing.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
A bug was introduced earlier in the development cycle when cleaning
up logic statements. Instead of skipping bits that are not set, set
bits are skipped, causing async interrupts to not be handled correctly.
To fix, simply add back in the proper evaluation for an unset bit.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Following a link up event, the LUNs available to the host may
have changed. Without rescanning the host, the LUN topology is
unknown to the user. In such a state, the user would be unable
to locate provisioned resources.
To remedy, the host should be rescanned after a link up event.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The resid is incorrectly set which can lead to unnecessary retry
attempts by the stack. This is due to resid _always_ being set
using a value returned from the adapter. Instead, the value
should only be interpreted and set when in an underrun scenario.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Borrowing the TMF waitq's spinlock causes a stall condition when
waiting for the TMF to complete. To remedy, introduce our own spin
lock to serialize TMF and use the appropriate wait services.
Also add a timeout while waiting for a TMF completion. When a TMF
times out, report back a failure such that a bigger hammer reset
can occur.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
During run-time the driver can be very chatty and spam the system
kernel log. Various print statements can be limited and/or moved
to development-only mode. Additionally, numerous prints can be
converted to trace the corresponding device. Lastly, one spelling
correction was made: 'entra' to 'extra'.
The following changes were made:
- pr_debug to pr_devel
- pr_debug to pr_debug_ratelimited
- pr_err to dev_err
- pr_debug to dev_dbg
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Implement the following suggestions and add two new attributes
to allow for debugging the port LUN table.
- use scnprintf() instead of snprintf()
- use DEVICE_ATTR_RO and DEVICE_ATTR_RW
Suggested-by: Shane Seymour <shane.seymour@hp.com>
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Found during code inspection, that the following functions are not
being used outside of the file where they are defined. Make them static.
int cxlflash_send_cmd(struct afu *, struct afu_cmd *);
void cxlflash_wait_resp(struct afu *, struct afu_cmd *);
int cxlflash_afu_reset(struct cxlflash_cfg *);
struct afu_cmd *cxlflash_cmd_checkout(struct afu *);
void cxlflash_cmd_checkin(struct afu_cmd *);
void init_pcr(struct cxlflash_cfg *);
int init_global(struct cxlflash_cfg *);
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Limbo is not an accurate representation of this state and is
also not consistent with the terminology that other drivers
use to represent this concept. Rename the state and and its
associated waitq to 'reset'.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
During an EEH freeze event, certain CXL services should not be
called until after the hardware reset has taken place. Doing so
can result in unnecessary failures and possibly cause other ill
effects by triggering hardware accesses. This translates to a
requirement to quiesce all threads that may potentially use CXL
runtime service during this window. In particular, multiple ioctls
make use of the CXL services when acting on contexts on behalf of
the user. Thus, it is essential to 'drain' running ioctls _before_
proceeding with handling the EEH freeze event.
Create the ability to drain ioctls by wrapping the ioctl handler
call in a read semaphore and then implementing a small routine that
obtains the write semaphore, effectively creating a wait point for
all currently executing ioctls.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The context encode mask covers more than 32-bits, making it
a long integer. This should be noted by appending the ULL
width suffix to the mask.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Using sizeof(bool) is considered poor form for various reasons and
sparse warns us of that. Correct by changing type from bool to u8.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
If the same virtual LUN is accessed over multiple cards, only accesses
made over the first card will be valid. Accesses made over the second
card will go to the wrong LUN causing data corruption.
This is because the global LUN's mode word was being used to determine
whether the LUN table for that card needs to be programmed. The mode
word would be setup by the first card, causing the LUN table for the
second card to not be programmed.
By unconditionally initializing the LUN table (not depending on the
mode word), the problem is avoided.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
When a LUN is removed, the sdev that is associated with the LUN
remains intact until its reference count drops to 0. In order
to prevent an sdev from being removed while a context is still
associated with it, obtain an additional reference per-context
for each LUN attached to the context.
This resolves a potential Oops in the release handler when a
dealing with a LUN that has already been removed.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The timeout value for read capacity is too small. Certain devices
may take longer to respond and thus the command may prematurely
timeout. Additionally the literal used for the timeout is stale.
Update the timeout to 30 seconds (matches the value used in sd.c)
and rework the timeout literal to a more appropriate description.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Magic numbers are not meaningful and can create confusion. As a
remedy, replace them with descriptive literals.
Replace 512 with literal MAX_SECTOR_UNIT.
Replace 5 with literal CMD_RETRIES.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
If two concurrent MANAGE_LUN ioctls are issued with the same
WWID parameter, it would result in an incorrect value of port_sel.
This is because port_sel is modified without any locks being
held. If the first caller stalls after the return from
find_and_create_lun(), the value of port_sel will be set
incorrectly to indicate a single port, though in this case
it should have been set to both ports.
To fix, use the global mutex to serialize the lookup of the
WWID and the subsequent modification of port_sel.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The "compatible" matching algorithm used for looking up old-style
blacklist entries in a scsi_dev_info_list is buggy. The core of the
algorithm looks like this:
if (memcmp(devinfo->vendor, vendor,
min(max, strlen(devinfo->vendor))))
/* not a match */
where max is the length of the device's vendor string after leading
spaces have been removed but trailing spaces have not. Because of the
min() computation, either entry could be a proper substring of the
other and the code would still think that they match.
In the case originally reported, the device's vendor and product
strings were "Inateck " and " ". These matched against
the following entry in the global device list:
{"", "Scanner", "1.80", BLIST_NOLUN}
because "" is a substring of "Inateck " and "" (the result of removing
leading spaces from the device's product string) is a substring of
"Scanner". The mistaken match prevented the system from scanning and
finding the device's second Logical Unit.
This patch fixes the problem by making two changes. First, the code
for leading-space removal is hoisted out of the loop. (This means it
will sometimes run unnecessarily, but since a large percentage of all
lookups involve the "compatible" entries in global device list, this
should be an overall improvement.) Second and more importantly, the
patch removes trailing spaces and adds a check to verify that the two
resulting strings are exactly the same length. This prevents matches
where one entry is a proper substring of the other.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Giulio Bernardi <ugilio@gmail.com>
Tested-by: Giulio Bernardi <ugilio@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
In drivers/scsi/scsi_devinfo.c, the scsi_dev_info_list_del_keyed() and
scsi_get_device_flags_keyed() routines contain a large amount of
duplicate code for finding vendor/product matches in a
scsi_dev_info_list. This patch factors out the duplicate code and
puts it in a separate function, scsi_dev_info_list_find().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Giulio Bernardi <ugilio@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
the kernel prints some warnings when compiled with CONFIG_DMA_API_DEBUG.
This is because the fnic driver doesn't check the return value of
pci_map_single().
[ 11.942770] scsi host12: fnic
[ 11.950811] ------------[ cut here ]------------
[ 11.950818] WARNING: at lib/dma-debug.c:937 check_unmap+0x47b/0x920()
[ 11.950821] fnic 0000:0c:00.0: DMA-API: device driver failed to check map error[device address=0x0000002020a30040] [size=44 bytes] [mapped as single]
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed By: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
We would like to get the following updates in:
Revert ownership to "Emulex" from "Avago Technologies"
Signed-off-by: Ketan Mukadam <ketan.mukadam@avagotech.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Do not log error for netevents that need no action such as
NETDEV_REGISTER 0x0005, NETDEV_CHANGEADDR, and NETDEV_CHANGENAME.
It results in logging error messages such as these
[ 35.315872] bnx2fc: Unknown netevent 5
[ 35.315935] bnx2fc: Unknown netevent 8
[ 35.353866] bnx2fc: Unknown netevent 10
and generating bug reports.
Remove logging this message as an ERROR instead of turning them into
either DEBUG or INFO level messages.
Signed-off-by: Shirish Pargaonkar <spargaonkar@suse.com>
Acked-by: Eddie Wai <eddie.wai@broadcom.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Initial link up defaults were not properly being tracked relative to
initial FLOGI or pt2pt PLOGI. Add code to initialize them.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Forgot to clear FCF Discovery in-progress flag upon FLOGI failures.
Thus we didn't restart FLOGI.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Fix for discovery failure in PT2PT when FLOGI's ELS ACC response gets aborted
Change login state machine to:
- Restart FLOGI if prior is ABTS'd
- Reject incoming FLOGIs if we have one pending
The above ensures that we always finish FLOGI processing, regardless
of who initated FLOGI, before processing PLOGI's.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
lpfc_send_rscn_event() allocates data for sizeof(struct
lpfc_rscn_event_header) + payload_len, but claims that the data has size
of sizeof(struct lpfc_els_event_header) + payload_len. That leads to
buffer overruns.
Signed-off-by: Ales Novak <alnovak@suse.cz>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Remove set but not used variables.
Signed-off-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This makes the function lpfc_sli4_mbox_completion's definition
static now in order to comply with its prototype being also
declared as static too.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Sebastian Herbszt <herbszt@gmx.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Currently the module parameter lpfc_sg_seg_count does not have effect
for sli3 devices.
In lpfc_sli_driver_resource_setup(), which is used for sli3, the code
writes the configured sg_seg_cnt into lpfc_template.sg_tablesize.
But lpfc_template is the template used for sli4 only. Thus the value should
correctly be written to lpfc_template_s3->sg_tablesize.
This patch is for kernel 4.1-rc5, but is tested with lpfc 10.2.405.26 only.
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Sebastian Herbszt <herbszt@gmx.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
kzalloc() returns a void pointer - no need to cast it in
drivers/scsi/lpfc/lpfc_init.c::lpfc_sli_driver_resource_setup()
Signed-off-by: Firo Yang <firogm@gmail.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Remove trailing space from model description.
Signed-off-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
3w controller don't dma map small single SGL entry commands but instead
bounce buffer them. Add a helper to identify these commands and don't
call scsi_dma_unmap for them.
Based on an earlier patch from James Bottomley.
Fixes: 118c85 ("3w-9xxx: fix command completion race")
Reported-by: Tóth Attila <atoth@atoth.sote.hu>
Tested-by: Tóth Attila <atoth@atoth.sote.hu>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This fixes a bug in recent kernels which results in failure to boot
on systems that have multipath SCSI disks. I observed this failure
on a POWER8 server where all the disks are multipath SCSI disks.
The symptoms are several messages like this on the console:
[ 3.018700] device-mapper: table: 253:0: multipath: error attaching hardware handler
[ 3.018828] device-mapper: ioctl: error adding target to table
and the system does not find its disks, and therefore fails to boot.
Bisection revealed that the bug was introduced in commit 566079c849,
"dm-mpath, scsi_dh: request scsi_dh modules in scsi_dh, not dm-mpath".
The specific reason for the failure is that where we previously loaded
the "scsi_dh_alua" module, we are now trying to load the "alua" module,
which doesn't exist.
To fix this, we change the request_module call in scsi_dh_lookup()
to prepend "scsi_dh_" to the name, just like the old code in
drivers/md/dm-mpath.c:parse_hw_handler() used to do.
[jejb: also fixes issue spotted by Sasha Levin that formatting
characters could be passed in via sysfs and cause issues with
request_module()]
Fixes: 566079c849
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Cc: Sasha Levin <sasha.levin@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Connection last_ping is not being updated when iscsi_send_nopout fails.
Not updating the last_ping will cause firing a timer to a past time
(last_ping + ping_tmo < current_time) which triggers an infinite loop of
iscsi_check_transport_timeouts() and hogs the cpu.
Fix this issue by checking the return value of iscsi_send_nopout.
If it fails set the next_timeout to one second later.
Signed-off-by: Ariel Nahum <arieln@mellanox.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Matthew R. Ochs