This patch moves the dev_hold call inside of nl-phy ieee802154_add_iface
function. The ieee802154_add_iface is the only one function which use the
ieee802154_if_add function and contains the corresponding dev_put call.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves and renames the mac802154_add_iface and
mac802154_netdev_register functions into iface.c. The function
mac802154_add_iface is renamed to ieee802154_if_add which is a similar naming
convention like mac80211.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves and rename the mac802154_del_iface function into
iface.c and rename the function to ieee802154_if_remove which is a similar
naming convention like mac80211.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The include/net/nl802154.h file contains a lot of prototypes which are
not used inside of ieee802154 subsystem. This patch removes this file
and make the only one used prototype "ieee802154_nl_start_confirm" as
static declaration in ieee802154/nl-mac.c
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch reworks the wpan_phy index incrementation. It's now similar
like wireless wiphy index incrementation. We move the wpan_phy index
attribute inside of cfg802154_registered_device and use atomic
operations instead locking mechanism via wpan_phy_mutex.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The ieee802154_is_valid_extended_addr() always returns true because
there is a typo. The || should be &&. Neither 0x0000000000000000ULL
nor 0xffffffffffffffffULL are valid addresses.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If you use RAW sockets the transport header offset is not set by the
ipv6 stack so when we get to the udp header compression it does not
compress the right part of the packet.
This patch adds a check for this scenario and sets the transport
header offset.
Signed-off-by: Simon Vincent <simon.vincent@xsilon.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixes the following sparse warnings in rfcomm/core.c:
net/bluetooth/rfcomm/core.c:391:16: warning: dubious: x | !y
net/bluetooth/rfcomm/core.c:546:24: warning: dubious: x | !y
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds an ieee802154_ptr to the net_device structure.
Furthermore the 802.15.4 subsystem will introduce a nl802154 framework
which is similar like the nl80211 framework and a wpan_dev structure.
The wpan_dev structure will hold additional net_device attributes like
address options which are 802.15.4 specific. In the upcoming nl802154
implementation we will introduce a NL802154_FLAG_NEED_WPAN_DEV like
NL80211_FLAG_NEED_WDEV. For this flag an ieee802154_ptr in net_device is
needed. Additional we can access the wpan_dev attributes in upper layers
like IEEE 802.15.4 6LoWPAN easily. Current solution is a complicated
callback interface and getting these values over subif data structure
in mac802154.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to Management Interface API 'Start Discovery' command should
generate a Command Complete event on failure. Currently kernel is
sending Command Status on early errors. This results in userspace
ignoring such event due to invalid size.
bluetoothd[28499]: src/adapter.c:trigger_start_discovery()
bluetoothd[28499]: src/adapter.c:cancel_passive_scanning()
bluetoothd[28499]: src/adapter.c:start_discovery_timeout()
bluetoothd[28499]: src/adapter.c:start_discovery_complete() status 0x0a
bluetoothd[28499]: Wrong size of start discovery return parameters
Reported-by: Jukka Taimisto <jtt@codenomicon.com>
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some drivers require knowledge of what connection handle is assigned
to what connection link type (ACL or SCO/eSCO). Instead of having each
driver implement connection tracking, provide a simple helper function
for lookup of the link type.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some vendors require special handling of the rx data from the USB
bulk endpoints. For that case provide an internal callback that
can overwrite it with a custom receive function.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The debufs entry for the BR/EDR whitelist is confusing since there is
a controller debugfs entry with the name white_list and both are two
different things.
With the BR/EDR whitelist, the actual interface in use is the device
list and thus just include all values from the internal BR/EDR whitelist
in the device_list debugfs entry.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Bluetooth controllers from Broadcom use a strict scanning filter
policy that filters based on Bluetooth device addresses and not on
RSSI. So tell the core about this.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some vendors decide to use a strict duplicate filter policy that only
filters on Bluetooth device addresses. This means that when the RSSI
changes, these devices are not reported again. During discovery it is
useful to actually get the RSSI updates.
Since this is specific to each controller, add a new quirk setting
that allows drivers to tell the core what kind of filtering policy
the controller uses.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Running make C=2 occurs warning:
symbol 'mac802154_config_ops' was not declared. Should it be static?
This patch adds a missing include in cfg.c to solve this warning.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reported-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Running make C=2 occurs in warnings:
symbol 'wpan_phy_class' was not declared. Should it be static?
symbol 'wpan_phy_sysfs_init' was not declared. Should it be static?
symbol 'wpan_phy_sysfs_exit' wasnot declared. Should it be static?
This patch adds a missing include "sysfs.h" to solve these warnings.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reported-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Running make C=2 occurs these warnings:
cast from restricted __be64
incorrect type in argument 1 (different base types)
expected unsigned long long[unsigned] [usertype] val
got restricted __be64 [usertype]<noident>
cast from restricted __be64
cast to restricted __le64
This patch fix these warnings by forcing to __le64 type and using swabp64
instead swab64.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reported-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fix byteorder issues which occurs because we compare __le64
with an host byteorder value. Simple add a cpu_to_le64 to convert the
host byteorder values to __le64.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reported-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Running make C=2 occurs warning:
constant 0xffffffffffffffff is so big it is unsigned long
This patch fix this warning by adding a ULL to the constant definitions.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reported-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Instead of having the driver generate the HCI Hardware Error event
manually, just call hci_reset_dev() to trigger the upper stack reset.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some Bluetooth drivers require to reset the upper stack. To avoid having
all drivers send HCI Hardware Error events, provide a generic function
to wrap the reset functionality.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The current kernel options do not make it clear which modules are for
Bluetooth Classic (BR/EDR) and which are for Bluetooth Low Energy (LE).
To make it really clear, introduce BT_BREDR and BT_LE options with
proper dependencies into the different modules. Both new options
default to y to not create a regression with previous kernel config
files.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When constructing the event payload for the HCI_Hardware_Error event
message, use the HCI_EV_HARDWARE_ERROR define.
In addition rename the variables from hard_err to hw_err to clearly
indicate that this is about the hardware error and not a hard error.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the HCI_Hardware_Error event is send by the controller or
injected by the driver, then at least print an error message.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the HCI_Reset command returns, the status needs to be checked. It
is unlikely that HCI_Reset actually fails, but when it fails, it is a
bad idea to reset all values since the controller will have not reset
its values in that case.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Currently the ieee802154 6lowpan interface operates on wpan interfaces
only. Setting the wpan mac address over 6lowpan interface is complex and
maybe we can't never do this. This patch removes the set of mac address
handling in ieee802154 6lowpan interface for now.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch use the validation function to check if an extended address
is valid or not while set the extended address.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduce an extended address validation helper to check if
an extended address is valid or not.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
All PHY attributes should be directly set to the transceiver after netlink.
MAC attributes should be set by interface up. Currently the macparams
netlink cmd contains mixed attributes of phy and mac settings. This patch
moves all phy settings to the netlink receive function for setting macparams.
This is the only way which doesn't change the userspace API and keep the
deprecated netlink interface alive.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves the setting of hardware panid address filtering
inside of interface up instead doing it it directly inside of netlink
interface. The netlink call which can only be called when netif isn't
running sets only the necessary panid value in sdata. After an
interface up the address filter will be set with this value.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves the setting of hardware short address filtering
inside of interface up instead doing it it directly inside of netlink
interface. The netlink call which can only be called when netif isn't
running sets only the necessary short_addr value in sdata. After an
interface up the address filter will be set with this value.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves the setting of hardware extended address filtering
inside of interface up instead doing it directly inside of netlink interface.
Also we don't need to set the sdata extended attribute in netlink. This
is already done by ndo_set_mac_address of net_device_ops.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a helper for converting the dev_addr attribute in
netdevice to __le64 type. The dev_addr attribute is a char pointer
and contains the extended address in big endian byte order.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch changes the actual behaviour for setting address attributes.
We should not change addresses while netif_running is true. Furthermore
when netif_running is running the address attributes becomes read only
and we can remove locking mechanism in receive and transmit hothpaths
of 802.15.4 subsystem.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the wpan_phy callbacks for add and del an interface
on a phy. Instead we introduce deprecated cfg802154 callbacks for this.
Furthermore we introduce a new netlink interface nl802154 which use
different callbacks. The deprecated function is to have a backwards
compatibility with the current netlink interface.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduce a function to get the cfg802154_registered_device
from a wpan_phy.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduces mac802154_config_ops struct. Like wireless this
struct should be the only one interface between ieee802154 to mac802154
or possible HardMAC drivers.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduce the cfg802154_registered_device struct. Like
cfg80211_registered_device in wireless this should contain similar
functionality for cfg802154. This patch should not change any behaviour.
We just adds cfg802154_registered_device as container for wpan_phy struct.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch sets the reset state channels accoridng at86rf2xx datasheets.
We don't need to set the default page here which is zero on all chips.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the default channel setting. A channel is always set
and there is no default channel setting according 802.15.4.
Drivers should set the default channel and page in probing routine. This
behaviour is currently a lack of all 802.15.4 drivers.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since commit e37d2ec82a ("mac802154: ops:
declare channel and page as u8") the page parameter can't be below zero.
This patch fix a kbuild test robot warning. Furthermore this check
should be removed and handled by netlink 802.15.4 interface.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
__hci_cmd_sync_ev(), __hci_req_sync() could miss wake_up_interrupt from
hci_req_sync_complete() because hci_cmd_work() workqueue and its response
could be completed before they are ready to get the signal through
add_wait_queue(), set_current_state(TASK_INTERRUPTIBLE).
Signed-off-by: Chan-yeol Park <chanyeol.park@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch add cfg80211 dump_survey handler for mwifiex.
This handler will be called to report channel statistics
to cfg80211.
This in turn adds ACS support for mwifiex AP.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support to record channel statistics during
scan. With extended scan, scan results are returned as events from
FW while channel statistics are part of scan command response.
We store these channel statistics in adapter.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Xinmin Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
H5 Specification says:
If a SYNC message is received while in the Active State, it is
assumed that the peer device has reset. The local device should
therefore perform a full reset of the upper stack, and start Link
Establishment again at the Uninitialized State. Upon entering the
Active State, the first packet sent shall have its SEQ and ACK
numbers set to zero.
This patch resets the HCI H5 driver data/state to unitialized and
reports an HCI hardware error event to notify the upper stack that
HCI synchronization has been lost. H5 will be re-synchronized and
upper stack should generate an HCI Reset command.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The kbuild test robot reports that there are extra semicolons in this
driver. All of them are caused by using "};" rather than "}" at the
end of a switch statement. This patch does not change any functionality.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Murilo Opsfelder Araujo <mopsfelder@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 802.11 statistics obtained from the device can be retrieved
dumping the 'macstat' file in debugfs folder.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>