The commit 658b476c74 ("pinctrl: baytrail: Add debounce configuration")
implements debounce for Baytrail pin control, but seems wasn't tested properly.
The register which keeps debounce value is separated from the configuration
one. Writing wrong values to the latter will guarantee wrong behaviour of the
driver and even might break something physically.
Besides above there is missed case how to disable it, which is actually done
through the bit in configuration register.
Rectify implementation here by using proper register for debounce value.
Fixes: 658b476c74 ("pinctrl: baytrail: Add debounce configuration")
Cc: Cristina Ciocan <cristina.ciocan@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This simplifies error handling and allows us to drop intel_pinctrl_remove()
completely.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are two bits in the PADCFG0 register to configure direction, one per
TX/RX buffers.
For now we wrongly assume that the GPIO is always requested before it is being
used, which is not true when the GPIO is used through irqchip. In this case the
GPIO is never requested and we never enable RX buffer for it.
Fix this by setting both bits accordingly.
Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
PADCFGLOCK (and PADCFGLOCK_TX) offset in Broxton actually starts at 0x060
and not 0x090 as used in the driver. Fix it to use the correct offset.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
SoC family such as DRA7 family of processors have, in addition
to the regular muxing of pins (as done by pinctrl-single), a separate
hardware module called IODelay which is also expected to be configured.
The "IODelay" module has it's own register space that is independent
of the control module and the padconf register area.
With recent changes to the pinctrl framework, we can now support
this hardware with a reasonably minimal driver by using #pinctrl-cells,
GENERIC_PINCTRL_GROUPS and GENERIC_PINMUX_FUNCTIONS.
It is advocated strongly in TI's official documentation considering
the existing design of the DRA7 family of processors during mux or
IODelay reconfiguration, there is a potential for a significant glitch
which may cause functional impairment to certain hardware. It is
hence recommended to do as little of muxing as absolutely necessary
without I/O isolation (which can only be done in initial stages of
bootloader).
NOTE: with the system wide I/O isolation scheme present in DRA7 SoC
family, it is not reasonable to do stop all I/O operations for every
such pad configuration scheme. So, we will let it glitch when used in
this mode.
Even with the above limitation, certain functionality such as MMC has
mandatory need for IODelay reconfiguration requirements, depending on
speed of transfer. In these cases, with careful examination of usecase
involved, the expected glitch can be controlled such that it does not
impact functionality.
In short, IODelay module support as a padconf driver being introduced
here is not expected to do SoC wide I/O Isolation and is meant for
a limited subset of IODelay configuration requirements that need to
be dynamic and whose glitchy behavior will not cause functionality
failure for that interface.
IMPORTANT NOTE: we take the approach of keeping LOCK_BITs cleared
to 0x0 at all times, even when configuring Manual IO Timing Modes.
This is done by eliminating the LOCK_BIT=1 setting from Step
of the Manual IO timing Mode configuration procedure. This option
leaves the CFG_* registers unprotected from unintended writes to the
CTRL_CORE_PAD_* registers while Manual IO Timing Modes are configured.
This approach is taken to allow for a generic driver to exist in kernel
world that has to be used carefully in required usecases.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[tony@atomide.com: updated to use generic pinctrl functions, added
binding documentation, updated comments]
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the pin controller driver is using devm_kzalloc, there may not be
anything to do for dt_free_map. Let's make it optional to avoid
unncessary boilerplate code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that we have a common pinctrl driver for all the sun5i SoCs, we can
remove the old, separate drivers.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The sun5i SoCs (A10s, A13, GR8) are all based on the same die fit in
different packages. Hence, the pins and functions available are just the
based on the same set, each SoC having a different subset.
Introduce a common pinctrl driver that supports multiple variants to allow
to put as much as we can in common.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some SoCs are either supposed to be pin compatible (A10 and A20 for
example), or are just repackaged versions of the same die (A10s, A13, GR8).
In those case, having a full blown pinctrl driver just introduces
duplication in both data size and maintainance effort.
Add a variant option to both pins and functions to be able to limit the
pins and functions described only to a subset of the SoC we support with a
given driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit df61b366af26 ('pinctrl: core: Use delayed work for hogs')
deferred part of the registration for pinctrl devices if the pinctrl
device has hogs. This introduced a window where if the pinctrl device
with hogs was sucessfully registered, but then unregistered again
(which could be caused by parent device being probe deferred) before
the delayed work has chanced to run, then this will cause a kernel
panic to occur because:
1. The 'pctldev->p' has not yet been initialised and when unregistering
the pinctrl device we only check to see if it is an error value, but
now it could also be NULL.
2. The pinctrl device may not have been added to the 'pinctrldev_list'
list and we don't check to see if it was added before removing.
Fix up the above by checking to see if the 'pctldev->p' pointer is an
error value or NULL before putting the pinctrl device and verifying
that the pinctrl device is present in 'pinctrldev_list' before removing.
Fixes: df61b366af26 ('pinctrl: core: Use delayed work for hogs')
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
3bfd44306c ("pinctrl: amd: Add support for additional GPIO")
created the following warning:
drivers/pinctrl/pinctrl-amd.c: In function 'amd_gpio_dbg_show':
drivers/pinctrl/pinctrl-amd.c:210:3: warning: 'pin_num' may be used uninitialized in this function [-Wmaybe-uninitialized]
for (; i < pin_num; i++) {
^
drivers/pinctrl/pinctrl-amd.c:172:21: warning: 'i' may be used uninitialized in this function [-Wmaybe-uninitialized]
unsigned int bank, i, pin_num;
^
Fix this by adding a guarding default case for illegal
bank numbers.
Cc: S-k Shyam-sundar <Shyam-sundar.S-k@amd.com>
Cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now using function_desc structure instead of imx_pmx_func.
Also leveraging generic functions to retrieve functions count/name/groups.
The imx_free_funcs function can be removed since it is now handled by
the core driver during unregister.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now using group_desc structure instead of imx_pin_group.
Also leveraging generic functions to retrieve groups count/name/pins.
The imx_free_pingroups function can be removed since it is now handled by
the core driver during unregister.
Finally the device tree parsing is moved after the pinctrl driver registration
since this latter initializes the radix trees.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These four pins are for SDC4, not SDC1. They are grouped for
SDC4 later in the file so this must be a typo.
Reviewed-by: Björn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We can now drop the driver specific code for managing functions.
Signed-off-by: Tony Lindgren <tony@atomide.com>
[Replaces GENERIC_PINMUX with GENERIC_PINMUX_FUNCTIONS]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We can now drop the driver specific code for managing groups.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We can add generic helpers for function handling for cases where the pin
controller driver does not need to use static arrays.
Signed-off-by: Tony Lindgren <tony@atomide.com>
[Renamed the Kconfig item and moved things around]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename the symbol PINCTRL_GENERIC to PINCTRL_GENERIC_GROUPS since
it all pertains to groups. Replace everywhere.
ifdef out the radix tree and the struct when not using the
generic groups.
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We can add generic helpers for pin group handling for cases where the pin
controller driver does not need to use static arrays.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It confused me a bit so it may confuse others. Make it crystal
clear what is going on here for any future readers.
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Having the pin control framework call pin controller functions
before it's probe has finished is not nice as the pin controller
device driver does not yet have struct pinctrl_dev handle.
Let's fix this issue by adding deferred work for late init. This is
needed to be able to add pinctrl generic helper functions that expect
to know struct pinctrl_dev handle. Note that we now need to call
create_pinctrl() directly as we don't want to add the pin controller
to the list of controllers until the hogs are claimed. We also need
to pass the pinctrl_dev to the device tree parser functions as they
otherwise won't find the right controller at this point.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes the wrong width of PINCFG_TYPE_DRV bitfields for Exynos5433
because PINCFG_TYPE_DRV of Exynos5433 has 4bit fields in the *_DRV
registers. Usually, other Exynos have 2bit field for PINCFG_TYPE_DRV.
Fixes: 3c5ecc9ed3 ("pinctrl: exynos: Add support for Exynos5433")
Cc: stable@vger.kernel.org
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This change is inspired from the pinctrl-single architecture.
The problem with current implementation is that it isn't possible
to add/remove functions and/or groups dynamically. The radix tree
offers an easy way to do so. The intent is to offer a follow-up
patch later that will enable the use of pinctrl nodes in dt-overlays.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Otherwise can't dynamically update fields such as ngroups which can
change over time (with a dt-overlay for instance).
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Trivial fixe to spelling mistake "Ivalid" to "Invalid" in
dev_err error message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a non-functional change, which deletes code duplication in two
of four if-if branches by reordering the checks. Functional identity
of the code change can be shown by running through the whole truth table
of boolean arguments.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch updates my email address as I no longer have access to the old
one.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add some tab in order to improve indentation.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reference to 'sys2pci_np' should be dropped in all cases here, not only in
error handling path.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This activates strict mode muxing for the STM32 pin controllers,
as these do not allow GPIO and functions to use the same pin
simultaneously.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinctrl_gpio_request is called with the "full" gpio number, already
containing the base, then meson_pmx_request_gpio is then called with the
final pin number.
Remove the base addition when calling meson_pmx_disable_other_groups.
Fixes: 6ac7309511 ("pinctrl: add driver for Amlogic Meson SoCs")
CC: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the function amd_gpio_irq_set_type, read the values from
the ACPI table to set the level and drop the settings passed
by the client.
Cc: <stable@vger.kernel.org> # 4.8.x+
Reviewed-by: Pankaj Sen <Pankaj.Sen@amd.com>
Reviewed-by: Nitesh Kumar Agrawal <Nitesh-kumar.Agrawal@amd.com>
Reviewed-by: Shah, Nehal-bakulchandra <Nehal-bakulchandra.Shah@amd.com>
Signed-off-by: Shyam-sundar S-k <Shyam-sundar.S-k@amd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds support for new Bank and adds IRQCHIP_SKIP_SET_WAKE flag.
Reviewed-by: S-k, Shyam-sundar <Shyam-sundar.S-k@amd.com>
Signed-off-by: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The patch introducing the g5 pinctrl driver implemented a smattering of
pins to flesh out the implementation of the core and provide bare-bones
support for some OpenPOWER platforms and the AST2500 evaluation board.
Now, update the bindings document to reflect the complete functionality
and implement the necessary pin configuration tables in the driver.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The patch introducing the g4 pinctrl driver implemented a smattering of
pins to flesh out the implementation of the core and provide bare-bones
support for some OpenPOWER platforms. Now, update the bindings document
to reflect the complete functionality and implement the necessary pin
configuration tables in the driver.
Cc: Timothy Pearson <tpearson@raptorengineering.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The System Control Unit IP block in the Aspeed SoCs is typically where
the pinmux configuration is found, but not always. A number of pins
depend on state in one of LPC Host Control (LHC) or SoC Display
Controller (GFX) IP blocks, so the Aspeed pinmux drivers should have the
means to adjust these as necessary.
We use syscon to cast a regmap over the GFX and LPC blocks, which is
used as an arbitration layer between the relevant driver and the pinctrl
subsystem. The regmaps are then exposed to the SoC-specific pinctrl
drivers by phandles in the devicetree, and are selected during a mux
request by querying a new 'ip' member in struct aspeed_sig_desc.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Voltage switching is the same as on the r8a7791.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds CAN FD[0-1] pinmux support to r8a7796 SoC.
Based on a patch for r8a7795 by Ramesh Shanmugasundaram.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds CAN[0-1] pinmux support to r8a7796 SoC.
Based on a patch for r8a7795 by Ramesh Shanmugasundaram.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
There are pins on the r8a7795 which are not part of a GPIO bank nor
can be muxed between different functions. They do however allow for the
bias to be configured. Add those pins to the list of pins and
to the bias configuration array.
The pins can now be referred to in DT by function names and their bias
setting set.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Implements pull-up and pull-down. On this SoC there is no simple mapping
of GP pins to bias register bits, so we need a table.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Define the drive strength registers for the R8A7796. Add pins which are
not part of a GPIO bank nor can be muxed between different functions but
which still allow for their drive-strength to be configured.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Lots of changes as usual, so I'm trying to be brief here. Most of the
new hardware support has the respective driver changes merged through
other trees or has had it available for a while, so this is where things
come together.
We get a DT descriptions for a couple of new SoCs, all of them variants
of other chips we already support, and usually coming with a new
evaluation board:
- Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices
- Qualcomm MDM9615 LTE baseband
- NXP imx6ull, the latest and smallest i.MX6 application processor variant
- Renesas RZ/G (r8a7743 and r8a7745) application processors
- Rockchip PX3, a variant of the rk3188 chip used in Android tablets
- Rockchip rk1108 single-core application processor
- ST stm32f746 Cortex-M7 based microcontroller
- TI DRA71x automotive processors
These are commercially available consumer platforms we now support:
- Motorola Droid 4 (xt894) mobile phone
- Rikomagic MK808 Android TV stick based on Rockchips rx3066
- Cloud Engines PogoPlug v3 based on OX820
- Various Broadcom based wireless devices:
- Netgear R8500 router
- Tenda AC9 router
- TP-LINK Archer C9 V1
- Luxul XAP-1510 Access point
- Turris Omnia open hardware router based on Armada 385
And a couple of new boards targeted at developers, makers
or industrial integration:
- Macnica Sodia development platform for Altera socfpga (Cyclone V)
- MicroZed board based on Xilinx Zynq FPGA platforms
- TOPEET itop/elite based on exynos4412
- WP8548 MangOH Open Hardware platform for IOT, based on
Qualcomm MDM9615
- NextThing CHIP Pro gadget
- NanoPi M1 development board
- AM571x-IDK industrial board based on TI AM5718
- i.MX6SX UDOO Neo
- Boundary Devices Nitrogen6_SOM2 (i.MX6)
- Engicam i.CoreM6
- Grinn i.MX6UL liteSOM/liteBoard
- Toradex Colibri iMX6 module
Other changes:
- added peripherals on renesas, davinci, stm32f429, uniphier, sti,
mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm,
mvebu, allwinner, broadcom, exynos, zynq
- Continued fixes for W=1 dtc warnings
- The old STiH415/416 SoC support gets removed, these never made it into
products and have served their purpose in the kernel as a template
for teh newer chips from ST
- The exynos4415 dtsi file is removed as nothing uses it.
- Intel PXA25x can now be booted using devicetree
Conflicts:
arch/arm/boot/dts/r8a*.dtsi: a node was added
the clk tree, keep both sides and watch out for git
dropping the required '};' at the end of each side.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wJt3
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"Lots of changes as usual, so I'm trying to be brief here. Most of the
new hardware support has the respective driver changes merged through
other trees or has had it available for a while, so this is where
things come together.
We get a DT descriptions for a couple of new SoCs, all of them
variants of other chips we already support, and usually coming with a
new evaluation board:
- Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices
- Qualcomm MDM9615 LTE baseband
- NXP imx6ull, the latest and smallest i.MX6 application processor variant
- Renesas RZ/G (r8a7743 and r8a7745) application processors
- Rockchip PX3, a variant of the rk3188 chip used in Android tablets
- Rockchip rk1108 single-core application processor
- ST stm32f746 Cortex-M7 based microcontroller
- TI DRA71x automotive processors
These are commercially available consumer platforms we now support:
- Motorola Droid 4 (xt894) mobile phone
- Rikomagic MK808 Android TV stick based on Rockchips rx3066
- Cloud Engines PogoPlug v3 based on OX820
- Various Broadcom based wireless devices:
- Netgear R8500 router
- Tenda AC9 router
- TP-LINK Archer C9 V1
- Luxul XAP-1510 Access point
- Turris Omnia open hardware router based on Armada 385
And a couple of new boards targeted at developers, makers or
industrial integration:
- Macnica Sodia development platform for Altera socfpga (Cyclone V)
- MicroZed board based on Xilinx Zynq FPGA platforms
- TOPEET itop/elite based on exynos4412
- WP8548 MangOH Open Hardware platform for IOT, based on Qualcomm MDM9615
- NextThing CHIP Pro gadget
- NanoPi M1 development board
- AM571x-IDK industrial board based on TI AM5718
- i.MX6SX UDOO Neo
- Boundary Devices Nitrogen6_SOM2 (i.MX6)
- Engicam i.CoreM6
- Grinn i.MX6UL liteSOM/liteBoard
- Toradex Colibri iMX6 module
Other changes:
- added peripherals on renesas, davinci, stm32f429, uniphier, sti,
mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm,
mvebu, allwinner, broadcom, exynos, zynq
- Continued fixes for W=1 dtc warnings
- The old STiH415/416 SoC support gets removed, these never made it
into products and have served their purpose in the kernel as a
template for teh newer chips from ST
- The exynos4415 dtsi file is removed as nothing uses it.
- Intel PXA25x can now be booted using devicetree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (422 commits)
arm: dts: zynq: Add MicroZed board support
ARM: dts: da850: enable high speed for mmc
ARM: dts: da850: Add node for pullup/pulldown pinconf
ARM: dts: da850: enable memctrl and mstpri nodes per board
ARM: dts: da850-lcdk: Add ethernet0 alias to DT
ARM: dts: artpec: add pcie support
ARM: dts: add support for Turris Omnia
devicetree: Add vendor prefix for CZ.NIC
ARM: dts: berlin2q-marvell-dmp: fix typo in chosen node
ARM: dts: berlin2q-marvell-dmp: fix regulators' name
ARM: dts: Add xo to sdhc clock node on qcom platforms
ARM: dts: r8a7794: Add device node for PRR
ARM: dts: r8a7793: Add device node for PRR
ARM: dts: r8a7792: Add device node for PRR
ARM: dts: r8a7791: Add device node for PRR
ARM: dts: r8a7790: Add device node for PRR
ARM: dts: r8a7779: Add device node for PRR
ARM: dts: r8a73a4: Add device node for PRR
ARM: dts: sk-rzg1e: add Ether support
ARM: dts: sk-rzg1e: initial device tree
...
No core changes this time. Mainly gradual improvement and
feature growth in the drivers.
New drivers:
- New driver for TI DA850/OMAP-L138/AM18XX pinconf
- The SX150x was moved over from the GPIO subsystem and
reimagined as a pin control driver with GPIO support
in a joint effort by three independent users of this
hardware. The result was amazingly good!
- New subdriver for the Oxnas OX820
Improvements:
- The sunxi driver now supports the generic pin control
bindings rather than the sunxi-specific. Add debouncing
support to the driver.
- Simplifications in pinctrl-single adding a generic parser.
- Two downstream fixes and move the Raspberry Pi BCM2835 over
to use the generic GPIOLIB_IRQCHIP.
-----BEGIN PGP SIGNATURE-----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=Pkzu
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl updates from Linus Walleij:
"Bulk pin control changes for the v4.10 kernel cycle:
No core changes this time. Mainly gradual improvement and
feature growth in the drivers.
New drivers:
- New driver for TI DA850/OMAP-L138/AM18XX pinconf
- The SX150x was moved over from the GPIO subsystem and reimagined as
a pin control driver with GPIO support in a joint effort by three
independent users of this hardware. The result was amazingly good!
- New subdriver for the Oxnas OX820
Improvements:
- The sunxi driver now supports the generic pin control bindings
rather than the sunxi-specific. Add debouncing support to the
driver.
- Simplifications in pinctrl-single adding a generic parser.
- Two downstream fixes and move the Raspberry Pi BCM2835 over to use
the generic GPIOLIB_IRQCHIP"
* tag 'pinctrl-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (92 commits)
pinctrl: sx150x: use new nested IRQ infrastructure
pinctrl: sx150x: handle missing 'advanced' reg in sx1504 and sx1505
pinctrl: sx150x: rename 'reg_advance' to 'reg_advanced'
pinctrl: sx150x: access the correct bits in the 4-bit regs of sx150[147]
pinctrl: mt8173: set GPIO16 to usb iddig mode
pinctrl: bcm2835: switch to GPIOLIB_IRQCHIP
pinctrl: New driver for TI DA850/OMAP-L138/AM18XX pinconf
devicetree: bindings: pinctrl: Add binding for ti,da850-pupd
Documentation: pinctrl: palmas: Add ti,palmas-powerhold-override property definition
pinctrl: intel: set default handler to be handle_bad_irq()
pinctrl: sx150x: add support for sx1501, sx1504, sx1505 and sx1507
pinctrl: sx150x: sort chips by part number
pinctrl: sx150x: use correct registers for reg_sense (sx1502 and sx1508)
pinctrl: imx: fix imx_pinctrl_desc initialization
pinctrl: sx150x: support setting multiple pins at once
pinctrl: sx150x: various spelling fixes and some white-space cleanup
pinctrl: mediatek: use builtin_platform_driver
pinctrl: stm32: use builtin_platform_driver
pinctrl: sunxi: Testing the wrong variable
pinctrl: nomadik: split up and comments MC0 pins
...
Core changes:
- Simplify threaded interrupt handling: instead of passing
numbed parameters to gpiochip_irqchip_add_chained() we
create a new call: gpiochip_irqchip_add_nested() so the two
types are clearly semantically different. Also make sure
that all nested chips call gpiochip_set_nested_irqchip()
which is necessary for IRQ resend to work properly if
it happens.
- Return error on seek operations for the chardev.
- Clamp values set as part of gpio[d]_direction_output() so
that anything != 0 will be send down to the driver as "1"
not the value passed in.
- ACPI can now support naming of GPIO lines, hogs and holes
in the GPIO lists.
New drivers:
- The SX150x driver was deemed unfit for the GPIO subsystem
and was moved over to a combined GPIO+pinctrl driver in the
pinctrl subsystem.
New features:
- Various cleanups to various drivers.
-----BEGIN PGP SIGNATURE-----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=2UpT
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Luinus Walleij:
"Bulk GPIO changes for the v4.10 kernel cycle:
Core changes:
- Simplify threaded interrupt handling: instead of passing numbed
parameters to gpiochip_irqchip_add_chained() we create a new call:
gpiochip_irqchip_add_nested() so the two types are clearly
semantically different. Also make sure that all nested chips call
gpiochip_set_nested_irqchip() which is necessary for IRQ resend to
work properly if it happens.
- Return error on seek operations for the chardev.
- Clamp values set as part of gpio[d]_direction_output() so that
anything != 0 will be send down to the driver as "1" not the value
passed in.
- ACPI can now support naming of GPIO lines, hogs and holes in the
GPIO lists.
New drivers:
- The SX150x driver was deemed unfit for the GPIO subsystem and was
moved over to a combined GPIO+pinctrl driver in the pinctrl
subsystem.
New features:
- Various cleanups to various drivers"
* tag 'gpio-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (49 commits)
gpio: merrifield: Implement gpio_get_direction callback
gpio: merrifield: Add support for hardware debouncer
gpio: chardev: Return error for seek operations
gpio: arizona: Tidy up probe error path
gpio: arizona: Remove pointless set of platform drvdata
gpio: pl061: delete platform data handling
gpio: pl061: move platform data into driver
gpio: pl061: rename variable from chip to pl061
gpio: pl061: rename state container struct
gpio: pl061: use local state for parent IRQ storage
gpio: set explicit nesting on drivers
gpio: simplify adding threaded interrupts
gpio: vf610: use builtin_platform_driver
gpio: axp209: use correct register for GPIO input status
gpio: stmpe: fix interrupt handling bug
gpio: em: depnd on ARCH_SHMOBILE
gpio: zx: depend on ARCH_ZX
gpio: x86: update config dependencies for x86 specific hardware
gpio: mb86s7x: use builtin_platform_driver
gpio: etraxfs: use builtin_platform_driver
...
Use the new gpiochip_irqchip_add_nested() and
gpiochip_set_nested_irqchip() calls to properly created
a nested irqchip and mark all child irqs properly with
their parent IRQ.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This fixes a problem where sx150x_regmap_reg_width() returns 8 for the
data register (reg 0) for sx1504 where it should return 4, and return
a correct 8 for sx1505 but for the wrong reason (both chips lack the
'advanced' register). This is not a real problem, since nothing depends
on the function returning 4 or 8, and certainly not if it is returning
8 for the wrong reason. But fix this to avoid nasty surprises down the
line.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This matches the datasheets and is less confusing since the register
has nothing to with advancing anything.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The code assumes 8-bit or 16-bit width registers, but three of the
chips (sx1501/sx1504/sx1507) are 4-bit. So, try to handle 4-bit chips as
well, they leave the high part of each register unused.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
the default mode of GPIO16 pin is gpio, when set EINT16 to
IRQ_TYPE_LEVEL_HIGH, no interrupt is triggered, it can be
fixed when set its default mode as usb iddig.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It should be possible to use the GPIOLIB_IRQCHIP helper
library with the BCM2835 driver since it is a pretty straight
forward cascaded irqchip.
The only difference from other drivers is that the BCM2835
has several banks for a single gpiochip, and each bank has
a separate IRQ line. Instead of creating one gpiochip per
bank, a single gpiochip covers all banks GPIO lines. This
makes it necessary to resolve the bank ID in the IRQ
handler.
The GPIOLIB_IRQCHIP allows several IRQs to be cascaded off
the same gpiochip by calling gpiochip_set_chained_irqchip()
repeatedly, but we have been a bit short on examples
for how this should be handled in practice, so this is intended
as an example of how this can be achieved.
The old code did not model the chip as a chained interrupt
handler, but this patch also rectifies that situation.
Cc: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Eric Anholt <eric@anholt.net>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a new driver for pinconf on TI DA850/OMAP-L138/AM18XX. These
SoCs have a separate controller for controlling pullup/pulldown groups.
Signed-off-by: David Lechner <david@lechnology.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We switch the default handler to be handle_bad_irq() instead of
handle_simple_irq() (which was not correct anyway).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
please pull the following:
- Rafal adds support for the Netgear R8500 routers, adds basic support
for the Tenda AC9 router which uses the new BCM53573 SoC (single core Cortex
A7). He also enables the UART on the Netgear R8000 and restructures the
include files a bit for the BCM47094 SoC, finally he adds USB 3.0 PHY nodes
which enables USB 3.0 on BCM5301X devices that support it. Finally he adds
support for the TP-LINK Archer C9 V1 router.
- Kamal adds support for the QSPI controller on the Northstar Plus SoCs and updates
the bcm958625k reference board to have it enabled
- Dan adds support for the Luxul XAP-1510 (using a BCM4708) and XWR-3100 (using
a BCM47094)
- Scott fixes the pinctrl names in the Cygnus DTS files
- Jonathan enables the Broadcom iProc mailbox controller for Broadcom Cygnus/iProc
SoCs, he adds interrupt support for the GPIO CRMU hardware block and finally adds
the node for the OTP controller found on Cygnus SoCs
- Dhananjay enables the GPIO B controller on Norstarh Plus SoCs
- Eric defines standard pinctrl groups in the BCM2835 GPIO node
- Gerd adds definitions for the pinctrl groups and updates the PWM, I2C and SDHCI nodes
to use their appropriate pinctrl functions
- Linus adds names for the Raspberry Pi GPIO lines based on the datasheet
- Martin adds the DT binding and nodes for the Raspberry Pi firmware thermal block
- Stefan fixes a few typos with respect to the BCM2835 mailbox binding example and
Device Tree nodes he also fixes the Raspberry Pi GPIO lines names and finally
adds names for the Raspberry Zero GPIO lines
-----BEGIN PGP SIGNATURE-----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=4GFQ
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.10/devicetree' of http://github.com/Broadcom/stblinux into next/dt
Pull "Broadcom devicetree changes for 4.10" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoC Device Tree changes for 4.10,
please pull the following:
- Rafal adds support for the Netgear R8500 routers, adds basic support
for the Tenda AC9 router which uses the new BCM53573 SoC (single core Cortex
A7). He also enables the UART on the Netgear R8000 and restructures the
include files a bit for the BCM47094 SoC, finally he adds USB 3.0 PHY nodes
which enables USB 3.0 on BCM5301X devices that support it. Finally he adds
support for the TP-LINK Archer C9 V1 router.
- Kamal adds support for the QSPI controller on the Northstar Plus SoCs and updates
the bcm958625k reference board to have it enabled
- Dan adds support for the Luxul XAP-1510 (using a BCM4708) and XWR-3100 (using
a BCM47094)
- Scott fixes the pinctrl names in the Cygnus DTS files
- Jonathan enables the Broadcom iProc mailbox controller for Broadcom Cygnus/iProc
SoCs, he adds interrupt support for the GPIO CRMU hardware block and finally adds
the node for the OTP controller found on Cygnus SoCs
- Dhananjay enables the GPIO B controller on Norstarh Plus SoCs
- Eric defines standard pinctrl groups in the BCM2835 GPIO node
- Gerd adds definitions for the pinctrl groups and updates the PWM, I2C and SDHCI nodes
to use their appropriate pinctrl functions
- Linus adds names for the Raspberry Pi GPIO lines based on the datasheet
- Martin adds the DT binding and nodes for the Raspberry Pi firmware thermal block
- Stefan fixes a few typos with respect to the BCM2835 mailbox binding example and
Device Tree nodes he also fixes the Raspberry Pi GPIO lines names and finally
adds names for the Raspberry Zero GPIO lines
* tag 'arm-soc/for-4.10/devicetree' of http://github.com/Broadcom/stblinux: (29 commits)
ARM: bcm2835: Add names for the RPi Zero GPIO lines
ARM: bcm2835: Fix names for the Raspberry Pi GPIO lines
ARM: dts: enable GPIO-b for Broadcom NSP
ARM: BCM5301X: Add DT for TP-LINK Archer C9 V1
ARM: dts: Add node for Broadcom OTP controller driver
ARM: dts: Enable interrupt support for cygnus crmu gpio driver
ARM: dts: Enable Broadcom iProc mailbox controller
ARM: bcm2835: Add names for the Raspberry Pi GPIO lines
ARM: bcm2835: dts: add thermal node to device-tree of bcm283x
dt: bindings: add thermal device driver for bcm2835
ARM: dts: bcm283x: fix typo in mailbox address
DT: binding: bcm2835-mbox: fix address typo in example
ARM: dts: cygnus: fix naming of pinctrl node
ARM: BCM53573: Specify PMU and its ILP clock in the DT
ARM: BCM5301X: Add DT for Luxul XWR-3100
ARM: BCM5301X: Add DT for Luxul XAP-1510
ARM: BCM5301X: Specify USB 3.0 PHY in DT
ARM: BCM5301X: Enable UART on Netgear R8000
ARM: BCM5301X: Add separated DTS include file for BCM47094
ARM: dts: NSP: Add QSPI nodes to NSPI and bcm958625k DTSes
...
All other registers on these chips are 8-bit, but reg_sense is 16-bits
and therefore needs to be moved down one notch.
This was apparently overlooked in the conversion to regmap, which only
updated the register locations for the 16-bit chips.
Fixes: 6489677f86 ("pinctrl-sx150x: Replace sx150x_*_cfg by means of regmap API")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the chip does not have an oscio pin, all pins are configured in
the same regmap register making it trivial to update all pins at
once, so do that. If an oscio pin is present, there needs to be
more locking in place to handle all cases correctly, so this is
skipped.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use builtin_platform_driver() helper to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Acked-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use builtin_platform_driver() helper to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Smatch complains that we dereference "map" before testing it for NULL
which is true. We should be testing "*map" instead. Also on the error
path, we should free *map and set it to NULL.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We should return -ENOMEM instead of success if pcs_add_function() fails.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gcc warns about a way that it could use an uninitialized variable:
drivers/pinctrl/sunxi/pinctrl-sunxi.c: In function 'sunxi_pinctrl_init':
drivers/pinctrl/sunxi/pinctrl-sunxi.c:1191:8: error: 'best_div' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This cannot really happen except if 'freq' is UINT_MAX and 'clock' is
zero, and both of these are forbidden. To shut up the warning anyway,
this changes the logic to initialize the return code to the first
divider value before looking at the others.
Fixes: 7c926492d3 ("pinctrl: sunxi: Add support for interrupt debouncing")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- DU and EtherAVB pin groups for R-Car M3-W,
- Bias handling cleanups and bug fixes,
- Drive-strength for non-GPIO pins for R-Car H3,
- EtherAVB MDIO & MII, and QSPI pin groups for R-Car H3.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJYLCe5AAoJEEgEtLw/Ve77SAgP+wRwaOkTA4xToYo2n3l5FyYH
IjOiDMmFKtP+Jk/mpcIphVORASP8jl39FoJI7wWVN+IqJciIdGH7ygQfGJOdqsZL
EOd6Ogxkb0z+N1GJIup3VH57Uy6q+3vMG2SARAyuOzVwt4sv04cCEhm7r5ZRCsB+
YSSKUufF7SOvG0kASR0iHGxW88GxROyH4JbJDLUK8gsGZyAy5X3I1GbJBvANelGv
Y+vy+bEdPvG0ToVMUPRfq1m4+wLZ47jwS6inXnOzk1A69HfZXCP/T0uvv92LDaTl
5VbWHkDZ8vORZK+BtrNi44BRWqMUPmlgHG0q7Ajiv18YQsxvLJAV6e/0t8yQMHoq
NGSVSfiS/ggsLdWAcbFgwMq9d+6alrRZjOFFMUjhF76WUK+b0DdZBezm2qCIVIh5
zBs7YISbRzUSTHZh3zHUDGWbryJD6vKs2fOibDEgSTP5e2NXvJI+d20P14l7L3ZN
q2kkfk6fAbJ+z29loXa1TjOSgJFown9CuWvuhVzLEiXVvugeNvDkg0YVXGF5ql+V
fQXzqIAUM40Emmfi6eFBMP9DKzjO/SkE5sLoFPrwoRvWRVHYAOMEt4eY1Zrk2Ve3
UX/hdn8O79mXtWHuTxaWKMDL2DAtlGXJpN5H2Im3N3eoTfaDTfFLtk7xDDNvDQm+
k8UzUUyO/xDSPHjF7ybV
=Mv9x
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.10-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.10 (take two)
- DU and EtherAVB pin groups for R-Car M3-W,
- Bias handling cleanups and bug fixes,
- Drive-strength for non-GPIO pins for R-Car H3,
- EtherAVB MDIO & MII, and QSPI pin groups for R-Car H3.
This add pinctrl support for Rockchip RK1108 Soc.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Series-changes: 2
- add pull and drive-strength functionality
Series-changes: 3
- two minor CodingStyle fixes adviced by Heiko
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Group the QSPI0 and QSPI1 pins into similar groups found in other sh-pfc
drivers. The pins can not be muxed between functions other than QSPI,
but their drive strength can be controlled.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Group the AVB pins into similar groups found in other sh-pfc drivers.
The pins can not be muxed between functions other then AVB but their
drive strength can be controlled.
The group avb_mdc containing ADV_MDC and ADV_MDIO are on other SoCs
called avb_mdio. In pfc-r8a7795 the avb_mdc group already existed and
is in use in DT. Therefore add the ADV_MDIO pin to the existing group
instead of renaming it.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
There are pins on the r8a7795 which are not part of a GPIO bank nor
can be muxed between different functions. They do however allow for the
drive-strength to be configured. Add those pins to the list of pins and
to the drive-strength configuration registers.
The pins can now be referred to in DT by function names and their
drive-strength modified.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Pins not associated with a GPIO port can still have other configuration
parameters. Add a new macro SH_PFC_PIN_NAMED_CFG which allows for named
pins to be declared with a set of configurations. The new macro is an
modification of SH_PFC_PIN_NAMED to allow for optional configuration to
be assigned.
The flag SH_PFC_PIN_CFG_NO_GPIO is still enforced as this should only be
used to define pins not associated with a GPIO port.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Change the data structure and use the generic sh_pfc_pin_to_bias_info()
function to get the register offset and bit information.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
There is a bug in the r8a7795 bias code where a WARN() is trigged
anytime a pin from PUEN0/PUD0 is accessed.
# cat /sys/kernel/debug/pinctrl/e6060000.pfc/pinconf-pins
WARNING: CPU: 2 PID: 2391 at drivers/pinctrl/sh-pfc/pfc-r8a7795.c:5364 r8a7795_pinmux_get_bias+0xbc/0xc8
[..]
Call trace:
[<ffff0000083c442c>] r8a7795_pinmux_get_bias+0xbc/0xc8
[<ffff0000083c37f4>] sh_pfc_pinconf_get+0x194/0x270
[<ffff0000083b0768>] pin_config_get_for_pin+0x20/0x30
[<ffff0000083b11e8>] pinconf_generic_dump_one+0x168/0x188
[<ffff0000083b144c>] pinconf_generic_dump_pins+0x5c/0x98
[<ffff0000083b0628>] pinconf_pins_show+0xc8/0x128
[<ffff0000081fe3bc>] seq_read+0x16c/0x420
[<ffff00000831a110>] full_proxy_read+0x58/0x88
[<ffff0000081d7ad4>] __vfs_read+0x1c/0xf8
[<ffff0000081d8874>] vfs_read+0x84/0x148
[<ffff0000081d9d64>] SyS_read+0x44/0xa0
[<ffff000008082f4c>] __sys_trace_return+0x0/0x4
This is due to the WARN() check if the reg field of the pullups struct
is zero, and this should be 0 for pins controlled by the PUEN0/PUD0
registers since PU0 is defined as 0. Change the data structure and use
the generic sh_pfc_pin_to_bias_info() function to get the register
offset and bit information.
Fixes: 560655247b ("pinctrl: sh-pfc: r8a7795: Add bias pinconf support")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The last else statement is missing braces, and the indentation level can
be reduced.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
On some SoC there are no simple mapping of pins to bias register bits
and a lookup table is needed. This logic is already implemented in some
SoC specific drivers that could benefit from a generic implementation.
Add helpers to deal with the lookup which later can be used by the SoC
specific drivers. The logic used to lookup are different from the one it
aims to replace, this is intentional. This new method reduces the memory
consumption at the cost of increased CPU usage and fix a bug where a
WARN() would incorrectly be triggered if the register offset is 0.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Always stating PIN_CONFIG_BIAS_DISABLE is supported gives untrue output
when examining /sys/kernel/debug/pinctrl/e6060000.pfc/pinconf-pins if
the operation get_bias() is implemented but the pin is not handled by
the get_bias() implementation. In that case the output will state that
"input bias disabled" indicating that this pin has bias control
support.
Make support for PIN_CONFIG_BIAS_DISABLE depend on that the pin either
supports SH_PFC_PIN_CFG_PULL_UP or SH_PFC_PIN_CFG_PULL_DOWN. This also
solves the issue where SoC specific implementations print error messages
if their particular implementation of {set,get}_bias() is called with a
pin it does not know about.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Only the DU parallel RGB output signals are included, HDMI and TCON pins
will be added in separate groups. Based on a similar patch from Laurent
Pinchart for the r8a7795 PFC driver.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The pin controller found in the Allwinner SoCs has support for interrupts
debouncing.
However, this is not done per-pin, preventing us from using the generic
pinconf binding for that, but per irq bank, which, depending on the SoC,
ranges from one to five.
Introduce a device-wide property to deal with this using a microsecond
resolution. We can re-use the per-pin input-debounce property for that, so
let's do it!
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The sunxi_pconf_reg helper introduced in the last patch gives us the
chance to rework sunxi_pconf_group_set to have it match the structure
of sunxi_pconf_(group_)get and make it easier to understand.
For each config to set, it:
1. checks if the parameter is supported.
2. checks if the argument is within limits.
3. converts argument to the register value.
4. writes to the register with spinlock held.
As a result the function now blocks unsupported config parameters,
instead of silently ignoring them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The sunxi pinctrl driver only caches whatever pinconf setting was last
set on a given pingroup. This is not particularly helpful, nor is it
correct.
Fix this by actually reading the hardware registers and returning
the correct results or error codes. Also filter out unsupported
pinconf settings. Since this driver has a peculiar setup of 1 pin
per group, we can support both pin and pingroup pinconf setting
read back with the same code. The sunxi_pconf_reg helper and code
structure is inspired by pinctrl-msm.
With this done we can also claim to support generic pinconf, by
setting .is_generic = true in pinconf_ops.
Also remove the cached config value. The behavior of this was never
correct, as it only cached 1 setting instead of all of them. Since
we can now read back settings directly from the hardware, it is no
longer required.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to pinconf-generic.h, the argument for
PIN_CONFIG_BIAS_PULL_{DOWN,UP} is non-zero if the bias is enabled
with a pull up/down resistor, zero if it is directly connected
to VDD or ground.
Since Allwinner hardware uses a weak pull resistor internally,
the argument should be 1.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the recently refactored sunxi pinctrl library, we are only allocating
one set of pin configs for each pinmux setting node. When the pinctrl_map
structure is freed, the pin configs should also be freed. However the
code assumed the first map would contain the configs, which actually
never happens, as the mux function map gets added first.
The proper way to do this is to look through all the maps and free the
first one whose type is actually PIN_MAP_TYPE_CONFIGS_GROUP.
Also slightly expand the comment explaining this.
Fixes: f233dbca62 ("pinctrl: sunxi: Rework the pin config building code")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
None of the Kconfigs for any of these drivers are tristate, meaning
that they currently are not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the drivers there is no doubt they are builtin-only. All
drivers get the exact same change, so they are handled in batch.
Changes are (1) use builtin_platform_driver, (2) use init.h header
(3) delete module_exit related code, (4) delete MODULE_DEVICE_TABLE,
(5) delete MODULE_LICENCE/MODULE_AUTHOR and associated tags and (6)
drop ".remove" code and prevent sysfs unbind attempts to call ".remove".
Once this is done, the shared remove function in wmt.[ch] is no longer
used and hence it is removed as well.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE etc. tags since all that information
is already contained at the top of each file in the comments.
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch add the support of GPF[1-5] pin of Exynos5433 SoC. The GPFx need
to support the multiple memory map because the registers of GPFx are located
in the different domain.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch supports the multiple IORESOURCE_MEM resources for one pin-bank.
In the pre-existing Exynos series, the registers of the gpio bank are included
in the one memory map. But, some gpio bank need to support the one more memory
map (IORESOURCE_MEM) because the registers of gpio bank are separated into
the different memory map.
For example,
The both ALIVE and IMEM domain have the different memory base address.
The GFP[1-5] of exynos5433 are composed as following:
- ALIVE domain : WEINT_* registers
- IMEM domain : CON/DAT/PUD/DRV/CONPDN/PUDPDN register
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: linux-gpio@vger.kernel.org
Suggested-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When dynamically unloading overlays, it is important that freed pins are
restored to being inputs to prevent functions from being enabled in
multiple places at once.
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Contrary to the documentation, the BCM2835 GPIO controller actually
has four interrupt lines - one each for the three IRQ groups and one
common. Confusingly, the GPIO interrupt groups don't correspond
directly with the GPIO control banks. Instead, GPIOs 0-27 generate IRQ
GPIO0, 28-45 IRQ GPIO1 and 46-53 IRQ GPIO2.
Awkwardly, the GPIOs for IRQ GPIO1 straddle two 32-entry GPIO banks,
so split out a function to process the interrupts for a single GPIO
bank.
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pcs_parse_bits_in_pinctrl_entry function should search
for the "pinctrl-single,bits" and not "pinctrl-single,pins"
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl_count_index_with_args returns -ENOENT not
-EINVAL. The return check would pass, and we would
try to kzalloc with a negative error size throwing
a warning.
Instead of checking for -EINVAL specifically, lets
check for any error and avoid negative size allocations.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
for_each_property_of_node(pins, pp) checks that pp is not NULL.
So there is no need to check it inside the loop.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
function is defined as unsigned int.
So we need %u to print it.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- I2C and DRIF pin groups for R-Car M3-W,
- Bug fixes for SDHI2/3 on R-Car M3-W.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PEV2
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.10-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.10
- I2C and DRIF pin groups for R-Car M3-W,
- Bug fixes for SDHI2/3 on R-Car M3-W.
Include <linux/gpio/driver.h> rather than <linux/gpio.h>
Drop <linux/pinctrl/machine.h>.
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Althought the function passed as a "handler" during GPIO chip
instantiation is not going to ever be called, specifying handle_edge_irq
there makes for a rather confusing read, both because no "ack" callback
in specified for irqchip and because there's no acking action is
necessary.
Specify handle_bad_irq instead a make a note of the situation. This
commit should be a no-op behaviour wise.
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make use of for_each_set_bit macro and reduce boilerplate code.
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move actual code that configures oscio pin into a separate function and
use it instead of calling sx150x_gpio_set to avoid calling
sx150x_pin_is_oscio twice and correctly propagte error code in
sx150x_gpio_direction_output.
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Gpiochip and irqchip aspects of this driver do not access any shared
registers on the chip itself and atomicity of various regmap operations
is ensured by that API's implementation, so there doesn't seem to be a
reason to hold the lock in as many places as it is held now.
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The difference between 8 and 16 pin GPIO expanders can be accomodated by
the means of regmap API without resorting to using driver-specific
read/write accessors. This change, IMHO, brings the following benefits:
- Replaces driver's idiosyncratic way of dealing with
mult-register fields with regmap API, which, hopefuly,
makes the code a bit easier for a new reader to understand
- Removes various multi-read for-loop register read logic
from various places in the code and puts it in a signle
place
- Removes ad-hoc IRQ register caching code in
sx150x_irq_bus_sync_unlock, since that functionality is
provided by regmap
Besided aforementioned benefits this change also implements necessary
RegSense byte swap necessary for SX1503 and SX1506 variants of the chip.
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For Sx1504/5/6 only SX1506 has RegAdvanced, so put some code in place to
account for that.
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the code configuring explicit IRQ acking into a standalone function
to declutter sx150x_init_hw a bit and make that code somewhat less
repetitious.
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to the datasheet for SX1504/5/6, RegAdvanced's
"Autoclear NINT" bit that turns the feature when set and disables it
when cleared, so writing 0x04 to the register will have the opposite
from desirable effect.
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add proper device specific information to of_device_id table of the
driver and add code to match against and fetch said data from it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix off-by-one (row and/or register) errors in links to Peripheral
Function Select Register bitfields from GPIO/Peripheral Function Select
Register 4 macros for SDHI2 and SDHI3 pins.
Based on rev. 0.52E of the R-Car Gen3 User's Manual.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
If a pin depending on bit 6 in SCU90 is requested for GPIO, the export
will succeed but changes to the GPIO's value will not be accepted by the
hardware. This is because the pinmux driver has misconfigured the SCU by
writing 1 to the reserved bit.
The description of SCU90[6] from the datasheet is 'Reserved, must keep
at value ”0”'. The fix is to switch pinmux from the bit-flipping macro
to explicitly configuring the .enable and .disable values to zero.
The patch has been tested on an AST2500 EVB.
Fixes: 56e57cb6c0 (pinctrl: Add pinctrl-aspeed-g5 driver)
Reported-by: Uma Yadlapati <yadlapat@us.ibm.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Initial pinctrl driver for QCOM msm8994 platforms.
In order to continue the initial board support for QCOM msm8994/msm8992
presented in patches from Jeremy McNicoll <jeremymc@redhat.com>, let's put
a proper pinctrl driver in place.
Currently, the DT for these platforms uses the msm8x74 pinctrl driver to
enable basic UART. Beyond the first few pins the rest are different enough
to justify it's own driver.
Note: This driver is also used by QCOM's msm8992 platform as it's TLM block
is the same.
- Initial formatting and style was taken from the msm8x74 pinctrl driver
added by Björn Andersson <bjorn.andersson@linaro.org>
- Data was then adjusted per QCOM MSM8994v2 documentation for Top Level
Multiplexing
- Bindings documentation was based on qcom,msm8996-pinctrl.txt by
Joonwoo Park <joonwoop@codeaurora.org> and then modified for msm8994
content
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
None of the Kconfigs for any of these drivers are tristate,
meaning that they currently are not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the drivers there is no doubt they are builtin-only. All
drivers get essentially the same change, so they are handled in batch.
Changes are (1) use builtin_platform_driver, (2) use init.h header
(3) delete module_exit related code, (4) delete MODULE_DEVICE_TABLE,
and (5) delete MODULE_LICENCE/MODULE_AUTHOR and associated tags.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We do delete the MODULE_LICENSE etc. tags since all that information
is already contained at the top of each file in the comments.
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Hongzhou Yang <hongzhou.yang@mediatek.com>
Cc: Fabian Frederick <fabf@skynet.be>
Cc: Maxime Coquelin <maxime.coquelin@st.com>
Cc: Vishnu Patekar <vishnupatekar0510@gmail.com>
Cc: Mylene Josserand <mylene.josserand@free-electrons.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for the Amlogic Meson GXL SoC, this is a partially complete
definition only based on the Amlogic Vendor tree.
This definition differs a lot from the GXBB and needs a separate entry.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We can now use generic parser and keep things compatible with the
old binding.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We can now use generic parser. To support the legacy binding without
#pinctrl-cells, add pcs_quirk_missing_pinctrl_cells() and warn about
missing #pinctrl-cells.
Let's also update the documentation for struct pcs_soc_data while at it
as that seems to be out of date.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When the system is suspended to S3 the BIOS might re-initialize certain
GPIO pins back to their original state or it may re-program interrupt mask
of others. For example Acer TravelMate B116-M had BIOS bug where certain
GPIO pin (MF_ISH_GPIO_5) was programmed to trigger on high level, and the
pin state was high once the BIOS gave control to the OS on resume.
This triggers lots of messages like:
irq 117, desc: ffff88017a61e600, depth: 1, count: 0, unhandled: 0
->handle_irq(): ffffffff8109b613, handle_bad_irq+0x0/0x1e0
->irq_data.chip(): ffffffffa0020180, chv_pinctrl_exit+0x2d84/0x12 [pinctrl_cherryview]
->action(): (null)
IRQ_NOPROBE set
We reset the mask back to known state in chv_pinctrl_resume() but that is
called only after device interrupts have already been enabled.
Now, this particular issue was fixed by upgrading the BIOS to the latest
(v1.23) but not everybody upgrades their BIOSes so we fix it up in the
driver as well.
Prevent the possible interrupt storm by moving suspend and resume hooks to
be called at _noirq time instead. Since device interrupts are still
disabled we can restore the mask back to known state before interrupt storm
happens.
Cc: stable@vger.kernel.org
Reported-by: Christian Steiner <christian.steiner@outlook.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If async suspend is enabled, the driver may access registers concurrently
with another instance which may fail because of the bug in Cherryview GPIO
hardware. Prevent this by taking the shared lock while accessing the
hardware in suspend and resume hooks.
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since the BCM2835 datasheet doesn't exactly specify the set-up time for
the GPIO Pull-up/down Clock Registers there was an assumption of 150 cycles
at a clock rate of 1 MHz. During a discussion [1] in the Raspberry Pi forum
it turns out that clock rate refers to the VPU which has a rate of 250 MHz.
So we can reduce the delay to a sensible value and update the comment above.
I tested this optimization with a Raspberry Pi B and a multimeter.
[1] - https://www.raspberrypi.org/forums/viewtopic.php?f=72&t=163352
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Printing the prefix does not provide any additional information. In
addition this makes the output look more consistent with pinctrl-intel.c.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The hardware supports a 16 and 8 bit wide NAND bus, let users pick
either.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Group index is incremented on every new group parsed. Since the
field is part of struct imx_pinctrl_soc_info, which is typically
a global variable passed by the individual pinctrl-imx.c based
driver, it does not get cleared automatically when re-probing the
driver. This lead imx_pinctrl_parse_functions passing a group
pointer which is outside of the allocated group space on second
probe and onwards. Typically this ended up in a NULL pointer
dereference when accessing the name field like this:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
...
PC is at strcmp+0x18/0x44
LR is at imx_dt_node_to_map+0xc4/0x290
Avoid this by setting group_index to 0 on probe.
This has been observed when using DEBUG_TEST_DRIVER_REMOVE.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch allows to probe stm32 pinctrl driver even if no interrupt
controller is defined to manage gpio irqs.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Thanks to 332e99d5ae which now alerts of default
trigger usage when configuring interrupts.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit 44a7185c2a ("of/platform: Add common method to populate
default bus"), ARM64 platform devices are populated at the
arch_initcall_sync level; as a result, the platform_driver_probe calls
in both the iProc and NSP GPIO drivers fail with -ENODEV since by that
time the platform device was not yet registered.
Replace platform_driver_probe with platform_driver_register, that allow
the device to be register later
Fixes: 44a7185c2a ("of/platform: Add common method to populate default bus")
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Tested-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for pin output control through the pinctrl config:
- support enabling/disabling output on a given pin
- support output level setting (high or low)
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Even though the our binding had the assumption that the allwinner,pull and
allwinner,drive properties were optional, the code never took that into
account.
Fix that.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pin config get() and set() handlers for pin groups were previously not
implemented by this driver. The pin_config_group_set() is particularly useful
for applying a common config setting to all pins in a specified group with a
single call, without the caller needing to reference each individual pin by
name.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
During pinmux registration, pinmux table is parsed from DT
for making the pinmux table configuration of pins.
Parse the only those node whose status is not disabled.
This will help on reusing the pin configuration table across
platform and disabling the node by status property if that node
is not needed on given platform.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Drivers using pinconf_generic_params tables cannot be built with
CONFIG_OF disabled:
drivers/pinctrl/pinctrl-max77620.c:53:44: error: array type has incomplete element type ‘struct pinconf_generic_params’
drivers/pinctrl/pinctrl-max77620.c:55:3: error: field name not in record or union initializer
drivers/pinctrl/pinctrl-max77620.c:55:3: note: (near initialization for ‘max77620_cfg_params’)
drivers/pinctrl/pinctrl-max77620.c:56:3: error: field name not in record or union initializer
This adds a dependency for max77620 to disallow that configuration.
Alternatively, we could rework the pinctrl infrastructure to make the
configuration valid for compile-testing.
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Lee Jones <lee.jones@linaro.org>
Fixes: 453943dc8f45 ("mfd: Enable compile testing for max77620 and max77686")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is left over from initial experiments with more properties.
It's only used in one place, so let's just get rid of it to make
the code more readable.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
>From tony Mon Sep 17 00:00:00 2001
From: Tony Lindgren <tony@atomide.com>
Date: Tue, 25 Oct 2016 08:33:34 -0700
Subject: [PATCHv2] pinctrl: single: Drop custom names
We no longer need to allocate custom names as those are dynamically
generated in pinctrl_register_one_pin() if no name is passed to
pinctrl_register_pins().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since the I2C sx150x GPIO expander driver uses platform_data to manage
the pins configurations, rewrite the driver as a pinctrl driver using
pinconf to get/set pin configurations from DT or debugfs.
The pinctrl driver is functionnally equivalent as the gpio-only driver
and can use DT for pinconf. The platform_data confirmation is dropped.
This patchset removed the gpio-only driver and selects the Pinctrl driver
config instead. This patchset also migrates the gpio dt-bindings to pinctrl
and add the pinctrl optional properties.
The driver was tested with a SX1509 device on a BeagleBone black with
interrupt support and on an X86_64 machine over an I2C to USB converter.
This is a fixed version that builds and runs on non-OF platforms and on
arm based OF. The GPIO version is removed and the bindings are also moved
to the pinctrl bindings.
Changes since v2
- rebased on v4.9-rc1
- removed MODULE_DEVICE_TABLE as in upstream bb411e771b
("gpio: sx150x: fix implicit assumption module.h is present")
Changes since v1
- Fix Kconfig descriptions on pinctrl and gpio
- Fix Kconfig dependency
- Remove oscio support for non-789 devices
- correct typo in dt bindings
- remove probe reset for non-789 devices
Changes since RFC
- Put #ifdef CONFIG_OF/CONFIG_OF_GPIO to remove OF code for non-of platforms
- No more rely on OF_GPIO config
- Moved and enhanced bindings to pinctrl bindings
- Removed gpio-sx150x.c
- Temporary select PINCTRL_SX150X when GPIO_SX150X
- Temporary mark GPIO_SX150X as deprecated
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
ested-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Our bindings are mostly irrelevant now that we have generic pinctrl
bindings that cover exactly the same uses cases.
Add support for the new ones, and obviously keep our old binding support in
order to keep the ABI stable.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for the Oxford Semiconductor OX820 which is similar as OX810 but
has 50 pins and two registers banks to setup alternate functions.
Add specific pins, groups and functions structures.
Add DT match data to select corresponding support.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add refactoring to move ox810se specific functions into specific ops structures
an add support for the dt match data to get soc specific structures.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
So far, putting NO_PULL in allwinner,pull was ignored, behaving like if
that property was not there at all.
Obviously, this is not the right thing to do, and in that case, we really
need to just disable the bias.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since we have some bindings header for our hardcoded flags, let's use them
when we can.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to support more easily the generic pinctrl properties, rework the
pinctrl maps configuration and split it into several sub-functions.
One of the side-effects from that rework is that we only parse the pin
configuration once, since it's going to be common to every pin, instead of
having to parsing once for each pin.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Dell XPS 13 (and maybe some others) uses a GPIO (CPU_GP_1) during suspend
to explicitly disable USB touchscreen interrupt. This is done to prevent
situation where the lid is closed the touchscreen is left functional.
The pinctrl driver (wrongly) assumes it owns all pins which are owned by
host and not locked down. It is perfectly fine for BIOS to use those pins
as it is also considered as host in this context.
What happens is that when the lid of Dell XPS 13 is closed, the BIOS
configures CPU_GP_1 low disabling the touchscreen interrupt. During resume
we restore all host owned pins to the known state which includes CPU_GP_1
and this overwrites what the BIOS has programmed there causing the
touchscreen to fail as no interrupts are reaching the CPU anymore.
Fix this by restoring only those pins we know are explicitly requested by
the kernel one way or other.
Cc: stable@vger.kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=176361
Reported-by: AceLan Kao <acelan.kao@canonical.com>
Tested-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Initialize the spinlock before using it.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 4.8.0-dwc-bisect #4
Hardware name: Intel Corp. VALLEYVIEW C0 PLATFORM/BYT-T FFD8, BIOS BLAKFF81.X64.0088.R10.1403240443 FFD8_X64_R_2014_13_1_00 03/24/2014
0000000000000000 ffff8800788ff770 ffffffff8133d597 0000000000000000
0000000000000000 ffff8800788ff7e0 ffffffff810cfb9e 0000000000000002
ffff8800788ff7d0 ffffffff8205b600 0000000000000002 ffff8800788ff7f0
Call Trace:
[<ffffffff8133d597>] dump_stack+0x67/0x90
[<ffffffff810cfb9e>] register_lock_class+0x52e/0x540
[<ffffffff810d2081>] __lock_acquire+0x81/0x16b0
[<ffffffff810cede1>] ? save_trace+0x41/0xd0
[<ffffffff810d33b2>] ? __lock_acquire+0x13b2/0x16b0
[<ffffffff810cf05a>] ? __lock_is_held+0x4a/0x70
[<ffffffff810d3b1a>] lock_acquire+0xba/0x220
[<ffffffff8136f1fe>] ? byt_gpio_get_direction+0x3e/0x80
[<ffffffff81631567>] _raw_spin_lock_irqsave+0x47/0x60
[<ffffffff8136f1fe>] ? byt_gpio_get_direction+0x3e/0x80
[<ffffffff8136f1fe>] byt_gpio_get_direction+0x3e/0x80
[<ffffffff813740a9>] gpiochip_add_data+0x319/0x7d0
[<ffffffff81631723>] ? _raw_spin_unlock_irqrestore+0x43/0x70
[<ffffffff8136fe3b>] byt_pinctrl_probe+0x2fb/0x620
[<ffffffff8142fb0c>] platform_drv_probe+0x3c/0xa0
...
Based on the diff it looks like the problem was introduced in
commit 71e6ca61e8 ("pinctrl: baytrail: Register pin control handling")
but I wasn't able to verify that empirically as the parent commit
just oopsed when I tried to boot it.
Cc: Cristina Ciocan <cristina.ciocan@intel.com>
Cc: stable@vger.kernel.org
Fixes: 71e6ca61e8 ("pinctrl: baytrail: Register pin control handling")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SPI1 function was associated with the wrong pins: The functions that
those pins provide is either an SPI debug or passthrough function
coupled to SPI1. Make the SPI1 mux function configure the relevant pins
and associate new SPI1DEBUG and SPI1PASSTHRU functions with the pins
that were already defined.
The notation used in the datasheet's multi-function pin table for the SoC is
often creative: in this case the SYS* signals are enabled by a single bit,
which is nothing unusual on its own, but in this case the bit was also
participating in a multi-bit bitfield and therefore represented multiple
functions. This fact was overlooked in the original patch.
Fixes: 56e57cb6c0 (pinctrl: Add pinctrl-aspeed-g5 driver)
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This prevented C20 from successfully being muxed as GPIO.
Fixes: 56e57cb6c0 (pinctrl: Add pinctrl-aspeed-g5 driver)
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixes simple typos in the initial commit. There is no behavioural
change.
Fixes: 56e57cb6c0 (pinctrl: Add pinctrl-aspeed-g5 driver)
Reported-by: Xo Wang <xow@google.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Consider a scenario with one pin P that has two signals A and B, where A
is defined to be higher priority than B: That is, if the mux IP is in a
state that would consider both A and B to be active on P, then A will be
the active signal.
To instead configure B as the active signal we must configure the mux so
that A is inactive. The mux state for signals can be described by
logical operations on one or more bits from one or more registers (a
"signal expression"), which in some cases leads to aliased mux states for
a particular signal. Further, signals described by multi-bit bitfields
often do not only need to record the states that would make them active
(the "enable" expressions), but also the states that makes them inactive
(the "disable" expressions). All of this combined leads to four possible
states for a signal:
1. A signal is active with respect to an "enable" expression
2. A signal is not active with respect to an "enable" expression
3. A signal is inactive with respect to a "disable" expression
4. A signal is not inactive with respect to a "disable" expression
In the case of P, if we are looking to activate B without explicitly
having configured A it's enough to consider A inactive if all of A's
"enable" signal expressions evaluate to "not active". If any evaluate to
"active" then the corresponding "disable" states must be applied so it
becomes inactive.
For example, on the AST2400 the pins composing GPIO bank H provide
signals ROMD8 through ROMD15 (high priority) and those for UART6 (low
priority). The mux states for ROMD8 through ROMD15 are aliased, i.e.
there are two mux states that result in the respective signals being
configured:
A. SCU90[6]=1
B. Strap[4,1:0]=100
Further, the second mux state is a 3-bit bitfield that explicitly
defines the enabled state but the disabled state is implicit, i.e. if
Strap[4,1:0] is not exactly "100" then ROMD8 through ROMD15 are not
considered active. This requires the mux function evaluation logic to
use approach 2. above, however the existing code was using approach 3.
The problem was brought to light on the Palmetto machines where the
strap register value is 0x120ce416, and prevented GPIO requests in bank
H from succeeding despite the hardware being in a position to allow
them.
Fixes: 318398c09a8d ("pinctrl: Add core pinctrl support for Aspeed SoCs")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Also delete (unused) private enum from driver.
The pull defines can be used instead if needed.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Driver updates for ARM SoCs, including a couple of newly added drivers:
- The Qualcomm external bus interface 2 (EBI2), used in some of their
mobile phone chips for connecting flash memory, LCD displays or
other peripherals
- Secure monitor firmware for Amlogic SoCs, and an NVMEM driver for the
EFUSE based on that firmware interface.
- Perf support for the AppliedMicro X-Gene performance monitor unit
- Reset driver for STMicroelectronics STM32
- Reset driver for SocioNext UniPhier SoCs
Aside from these, there are minor updates to SoC-specific bus,
clocksource, firmware, pinctrl, reset, rtc and pmic drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=GvTq
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, including a couple of newly added
drivers:
- The Qualcomm external bus interface 2 (EBI2), used in some of their
mobile phone chips for connecting flash memory, LCD displays or
other peripherals
- Secure monitor firmware for Amlogic SoCs, and an NVMEM driver for
the EFUSE based on that firmware interface.
- Perf support for the AppliedMicro X-Gene performance monitor unit
- Reset driver for STMicroelectronics STM32
- Reset driver for SocioNext UniPhier SoCs
Aside from these, there are minor updates to SoC-specific bus,
clocksource, firmware, pinctrl, reset, rtc and pmic drivers"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
bus: qcom-ebi2: depend on HAS_IOMEM
pinctrl: mvebu: orion5x: Generalise mv88f5181l support for 88f5181
clk: mvebu: Add clk support for the orion5x SoC mv88f5181
dt-bindings: EXYNOS: Add Exynos5433 PMU compatible
clocksource: exynos_mct: Add the support for ARM64
perf: xgene: Add APM X-Gene SoC Performance Monitoring Unit driver
Documentation: Add documentation for APM X-Gene SoC PMU DTS binding
MAINTAINERS: Add entry for APM X-Gene SoC PMU driver
bus: qcom: add EBI2 driver
bus: qcom: add EBI2 device tree bindings
rtc: rtc-pm8xxx: Add support for pm8018 rtc
nvmem: amlogic: Add Amlogic Meson EFUSE driver
firmware: Amlogic: Add secure monitor driver
soc: qcom: smd: Reset rx tail rather than tx
memory: atmel-sdramc: fix a possible NULL dereference
reset: hi6220: allow to compile test driver on other architectures
reset: zynq: add driver Kconfig option
reset: sunxi: add driver Kconfig option
reset: stm32: add driver Kconfig option
reset: socfpga: add driver Kconfig option
...
Subsystem improvements:
- Do away with the last users of the obsolete Kconfig options
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB (the latter
always sounded like an item on a wishlist to Santa Claus to
me). We can now select GPIOLIB and be done with it, for all
archs. After some struggle it even work on UM. Not that it has
GPIO, but if it wants to, it can select the library.
- Continued efforts to make drivers properly either tristate or
bool.
- Introduce a warning for drivers assigning default triggers to
their irqchip lines when probed from device tree, so we find and
fix these ambigous drivers. It is agreed that in the OF config
path, the device tree defines trigger characteristics.
- The same warning, mutatis mutandis, for ACPI-probed GPIO
irqchips.
- We introduce the ability to mark certain IRQ lines as "unusable"
as they can be taken by BIOS/firmware, unrouted in silicon and
generally nasty if you use them, and such things. This is
put to good use in the STMPE driver and also in the Cherryview
pin control driver.
- A new "mockup" virtual GPIO device that can be used for testing.
The plan is to add unit tests under tools/* for exercising this
device and verify that the kernel code paths are working as they
should.
- Make memory-mapped I/O-drivers depend on HAS_IOMEM. This was
implicit all the time, but when people started building UM
with allyesconfig or allmodconfig it exploded in their face.
- Move some stray bits of device tree and ACPI HW description
callbacks down into their respective implementation silo. These
were causing issues when compiling on !HAS_IOMEM as well, so
now eventually UM compiles the GPIOLIB library if it wants to.
New drivers:
- New driver for the Aspeed GPIO front-end companion to the
pin controller merged through the pin control tree.
- New driver for the LP873x PMIC GPIO portions.
- New driver for Technologic Systems' I2C FPGA GPIO such as
TS4900, TS-7970, TS-7990 and TS-4100.
- New driver for the Broadcom BCM63xx series including BCM6338
and BCM6345.
- New driver for the Intel WhiskeyCove PMIC GPIO.
- New driver for the Allwinner AXP209 PMIC GPIO portions.
- New driver for Diamond Systems 48 line GPIO-MM, another of
these port-mapped I/O expansion cards.
- Support the STMicroelectronics STMPE1600 variant in the STMPE
driver.
Driver improvements:
- The STMPE driver now supports rising/falling edge detection
properly for IRQs.
- The PCA954x will now fetch and enable its VCC regulator properly.
- Major rework of the PCA953x driver with the goal of eventually
switching it over to use regmap and thus modernize it even more.
- Switch the IOP driver to use the generic MMIO GPIO library.
- Move the ages old HTC EGPIO (extended GPIO) GPIO expander driver
over to this subsystem from MFD, achieveing some separation of
concerns.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJX9OvDAAoJEEEQszewGV1zsPQP/3VLy1fNIpMF0DDyq5tA/GNv
sinnaPgMtt+qBrM2sbJcTVwV9xtHrs12CC3+2lAhBCIEm4YfHbXvaUMNE+aKJzk4
ZM7/rb8WMUxjQqzDKStdETsQGo6fxh0qU81OEQNbX9alir20jik9DvTufcs6xCgx
sqh8KsNGO4Y6tiuKZ6mTZvIjVhMwiTm0NBSDKhdim0DdsOcuxyh6xVOj/0LB2Ei6
g75X1w++wjh0ryY3bzaeWkQSlXDC6eEKeez7VaEkSUyrxH86buomy0+aP0fqs7vY
LRZzn/TC97YLT6hslS/OhB7uXrDIY2POSwO/SvusJcveGP7WPGyGr5mDtA4ATRWI
ios0DBWl629kHfhAMzg3kPJS8LfjCerapvtbdAgqvhH+Vb5IPFx45vypDkR2WtJ7
bNAySIRMQSHZvJSCvYzjqh8AbWdE4i4k70tFXRMOpWeKIvRVI1cDvLD6cLn3hATM
IPTytM6i2xqnzcq7mK7EJ18afcR0mv1jHgGAv4M0RMkyJ2IrURvFyZIvUB2MTyuL
PEBh1ZvTs+MO50eeFwzltY91eagkzgWB0f6sm3l7I7bL2oxE2f/WVcVL9jWbgwpF
otjFO27u0/6rIulfLUQzDo3gbOq7UaN0VTW4E9CYbOtFtNzCxjFIKTv0IJhTu4TT
OSur7oFpzAMOGYlpYP8j
=ABbi
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.9 series:
Subsystem improvements:
- do away with the last users of the obsolete Kconfig options
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB (the latter
always sounded like an item on a wishlist to Santa Claus to me). We
can now select GPIOLIB and be done with it, for all archs. After
some struggle it even work on UM. Not that it has GPIO, but if it
wants to, it can select the library.
- continued efforts to make drivers properly either tristate or bool.
- introduce a warning for drivers assigning default triggers to their
irqchip lines when probed from device tree, so we find and fix
these ambigous drivers. It is agreed that in the OF config path,
the device tree defines trigger characteristics.
- the same warning, mutatis mutandis, for ACPI-probed GPIO irqchips.
- we introduce the ability to mark certain IRQ lines as "unusable" as
they can be taken by BIOS/firmware, unrouted in silicon and
generally nasty if you use them, and such things. This is put to
good use in the STMPE driver and also in the Cherryview pin control
driver.
- a new "mockup" virtual GPIO device that can be used for testing.
The plan is to add unit tests under tools/* for exercising this
device and verify that the kernel code paths are working as they
should.
- make memory-mapped I/O-drivers depend on HAS_IOMEM. This was
implicit all the time, but when people started building UM with
allyesconfig or allmodconfig it exploded in their face.
- move some stray bits of device tree and ACPI HW description
callbacks down into their respective implementation silo. These
were causing issues when compiling on !HAS_IOMEM as well, so now
eventually UM compiles the GPIOLIB library if it wants to.
New drivers:
- new driver for the Aspeed GPIO front-end companion to the pin
controller merged through the pin control tree.
- new driver for the LP873x PMIC GPIO portions.
- new driver for Technologic Systems' I2C FPGA GPIO such as TS4900,
TS-7970, TS-7990 and TS-4100.
- new driver for the Broadcom BCM63xx series including BCM6338 and
BCM6345.
- new driver for the Intel WhiskeyCove PMIC GPIO.
- new driver for the Allwinner AXP209 PMIC GPIO portions.
- new driver for Diamond Systems 48 line GPIO-MM, another of these
port-mapped I/O expansion cards.
- support the STMicroelectronics STMPE1600 variant in the STMPE
driver.
Driver improvements:
- the STMPE driver now supports rising/falling edge detection
properly for IRQs.
- the PCA954x will now fetch and enable its VCC regulator properly.
- major rework of the PCA953x driver with the goal of eventually
switching it over to use regmap and thus modernize it even more.
- switch the IOP driver to use the generic MMIO GPIO library.
- move the ages old HTC EGPIO (extended GPIO) GPIO expander driver
over to this subsystem from MFD, achieveing some separation of
concerns"
* tag 'gpio-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (81 commits)
gpio: add missing static inline
gpio: OF: localize some gpiochip init functions
gpio: acpi: separation of concerns
gpio: OF: separation of concerns
gpio: make memory-mapped drivers depend on HAS_IOMEM
gpio: stmpe: use BIT() macro
gpio: stmpe: forbid unused lines to be mapped as IRQs
mfd/gpio: Move HTC GPIO driver to GPIO subsystem
gpio: MAINTAINERS: Add an entry for GPIO mockup driver
gpio/mockup: add virtual gpio device
gpio: Added zynq specific check for special pins on bank zero
gpio: axp209: Implement get_direction
gpio: aspeed: remove redundant return value check
gpio: loongson1: remove redundant return value check
ARM: omap2: fix missing include
gpio: tc3589x: fix up complaints on unsigned
gpio: tc3589x: add .get_direction() and small cleanup
gpio: f7188x: use gpiochip_get_data instead of container_of
gpio: tps65218: use devm_gpiochip_add_data() for gpio registration
gpio: aspeed: fix return value check in aspeed_gpio_probe()
...
The following commit introduced a regression by not properly masking the
calculated value.
Fixes: 47a01ee9a6 ("pinctrl: qcom: Clear all function selection bits")
Signed-off-by: John Crispin <john@phrozen.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The generic GPIO library directly implement code for acpi_find_gpio()
which is only used with CONFIG_ACPI. This was probably done because
OF did the same thing, but I removed that so remove this too.
Rename the internal acpi_find_gpio() in gpiolib-acpi.c to
acpi_populate_gpio_lookup() which seems to be more appropriate anyway
so as to avoid a namespace clash with the same function.
Make the stub return -ENOENT rather than -ENOSYS (as that is for
syscalls!).
For some reason the sunxi pin control driver was including the private
gpiolib header, it works just fine without it so remove that oneliner.
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On some Intel BXT platform, wake-up from suspend-to-idle on pressing
power-button is not working. Its noticed that gpio-keys driver marking the
second level IRQ/power-button as wake capable but Intel pintctrl
driver is missing to mark GPIO chip/controller IRQ which first level IRQ
as wake cable if its GPIO pin IRQ is wakeble. So, though the first level
IRQ gets generated on power-button press, since it is not marked as
wake capable resume/wake-up flow is not happening.
Intel pintctrl/GPIO driver need to mark GPIO chip/controller IRQ (first
level IRQ) as wake capable iff GPIO pin's IRQ (second level IRQ) is marked
as wake cable.
Changes in v2:
- Add missing irq initialisation.
Signed-off-by: Nilesh Bacchewar <nilesh.bacchewar@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This simplifies the error handling and allows us to drop the whole
chv_pinctrl_remove() function.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It turns out that for north and southwest communities, they can only
generate GPIO interrupts for lower 8 interrupts (IntSel value). The upper
part (8-15) can only generate GPEs (General Purpose Events).
Now the reason why EC events such as pressing hotkeys does not work if we
mask all the interrupts is that in order to generate either interrupts or
GPEs the INTMASK register must have that particular interrupt unmasked. In
case of GPEs the CPU does not trigger normal interrupt (and thus the GPIO
driver does not see it) but instead it causes SCI (System Control
Interrupt) to be triggered with the GPE in question set.
To make this all work as expected we only add those GPIOs to the IRQ domain
that can actually generate interrupts (IntSel value 0-7) and skip others.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add pinctrl and clk support for the Orion5x SoC mv88f5181 variant
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlfiWTAACgkQCwYYjhRyO9X3ZQCfdOuvxXIajKkmxgvVwNgzEeLF
GEIAn1LYY/vmNikPhxH4O2FBi/9NBdZM
=GrPA
-----END PGP SIGNATURE-----
Merge tag 'mvebu-drivers-4.9-1' of git://git.infradead.org/linux-mvebu into next/drivers
Pull "mvebu drivers for 4.9 (part 1)" from Gregory CLEMENT:
- Add pinctrl and clk support for the Orion5x SoC mv88f5181 variant
* tag 'mvebu-drivers-4.9-1' of git://git.infradead.org/linux-mvebu:
pinctrl: mvebu: orion5x: Generalise mv88f5181l support for 88f5181
clk: mvebu: Add clk support for the orion5x SoC mv88f5181
As far as I'm aware the mv88f5181-b1 and mv88f5181l are the same at the
pinctrl level, so re-use the definitions for both.
[gregory.clement@free-electrons.com: fix commit title]
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
There is no point in adding any default trigger for these
GPIO interrupts: the device tree should contain all trigger
information and the platforms using the driver boots
exclusively from device tree.
Also the boot log is nagging me to fix this:
[ 0.771057] ------------[ cut here ]------------
[ 0.775695] WARNING: CPU: 0 PID: 1 at
../drivers/gpio/gpiolib.c:1622 _gpiochip_irqchip_add+0x138/0x160
[ 0.785034] /soc/gpio@8012e000: Ignoring 2 default trigger
(...)
[ 0.942962] gpio 8012e000.gpio: at address e08f8000
(etc ad nauseam)
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
STiH415/6 SoC support is being removed from the kernel.
This patch updates the ST pinctrl driver and removes
references to these obsolete platforms. As some structures
referenced by STiH407 based configuration were shared with
STiH416 we update these names to match the remaining
supported platform.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: <linus.walleij@linaro.org>
Cc: <linux-gpio@vger.kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add EE domains pins for the NAND flash controller.
Even tough we have no driver for the NAND flash controller yet, we need
to have these pins in pinctrl as the actual pin are shared with the spifc
controller. The bootloader on the S905-P200 setup pinmux for the NAND
controller so we need the kernel to properly deactivate this if necessary.
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The newly added irqchip support for the stm32 pinctrl driver uses
hierarchical IRQ domains as provided by the NVIC primary irqchip.
This works great for any configuration that may be relevant on
stm32, but when doing compile-testing (randconfig), we can
enable it without NVIC or any other primary irqchip that
enables IRQ_DOMAIN_HIERARCHY:
drivers/pinctrl/stm32/pinctrl-stm32.c:212:13: error: 'irq_chip_eoi_parent' undeclared here (not in a function)
drivers/pinctrl/stm32/pinctrl-stm32.c:213:20: error: 'irq_chip_mask_parent' undeclared here (not in a function)
drivers/pinctrl/stm32/pinctrl-stm32.c:214:20: error: 'irq_chip_unmask_parent' undeclared here (not in a function)
drivers/pinctrl/stm32/pinctrl-stm32.c:215:20: error: 'irq_chip_set_type_parent' undeclared here (not in a function)
This adds a Kconfig dependency to limit compile-testing to
configurations that have IRQ_DOMAIN_HIERARCHY already enabled.
It's not obvious whether we should use 'depends on' or 'select'
here, I think either one works, with 'depends on' being more
intuitive, while 'select' would be less likely to cause dependency
loops.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 0eb9f68333 ("pinctrl: Add IRQ support to STM32 gpios")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Return pinconf with arguments in packed format,
- MSIOF and QSPI pin groups on R-Car V2H,
- Voltage switching for SDHI on R-Car M2-W, E2, and M3-W.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=APGj
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.9-tag3' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.9 (take three)
- Return pinconf with arguments in packed format,
- MSIOF and QSPI pin groups on R-Car V2H,
- Voltage switching for SDHI on R-Car M2-W, E2, and M3-W.
All the SHDIs can operate with either 3.3V or 1.8V signals, depending
on negotiation with the card.
Based on work by Wolfram Sang for the r8a7790.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
All the SHDIs can operate with either 3.3V or 1.8V signals, depending
on negotiation with the card.
Based on work by Wolfram Sang for the r8a7790.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This follows the style of existing PORT_GP_X macros and
will be used by a follow-up patch for the r8a7791 SoC.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This adds the SDIO interrupt pin which can be used by sd_emmc_a.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Suggested-by: Neil Armstrong <narmstrong@baylibre.com>
Fixes: 29885a6565 ("pinctrl: meson-gxbb: add the pins for the
SDIO/sd_emmc_a controller")
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The newly added aspeed driver tries to check for a negative return
value from a pinctrl function, but stores the intermediate value in
a 'bool' variable, which cannot work:
drivers/pinctrl/aspeed/pinctrl-aspeed.c: In function 'aspeed_sig_expr_set':
drivers/pinctrl/aspeed/pinctrl-aspeed.c:192:11: error: comparison of constant '0' with boolean expression is always false [-Werror=bool-compare]
This slightly reworks the logic to use an explicit comparison with zero
before assigning to the temporary variable.
Reported-by: Colin King <colin.king@canonical.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These structures are only used to copy into other structures, so declare
them as const.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These structures are only used to copy into other structures, so declare
them as const.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The earlier patch can be simplified by using a bool
to indicate level trigger.
Reviewed-by: Pankaj Sen <Pankaj.Sen@amd.com>
Signed-off-by: Nitesh Kumar Agrawal <Nitesh-kumar.Agrawal@amd.com>
[Fixup to earlier manually applied patch]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds IRQ support to STM32 gpios.
The EXTI controller has 16 lines dedicated to GPIOs.
EXTI line n can be connected to only line n of one of the GPIO ports, for
example EXTI0 can be connected to either PA0, or PB0, or PC0...
This port selection is done by specifying the port number into System
Config registers.
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
samsung_pinctrl_probe() can be called only after matching
the driver by the compatible string so this already implies
a non null dev->of_node. Remove the always false test
and related error trace. While at it drop another error log
in case of memory allocation failure - any errors are logged
by the memory subsystem.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In function mrfld_pinctrl_probe(), when duplicating the mrfld_families
array the requested memory region length is multiplied once too many by the
number of elements in the original array. Fix this to spare some memory.
Fixes: 4e80c8f505 ("pinctrl: intel: Add Intel Merrifield pin controller support")
Signed-off-by: Vincent Stehlé <vincent.stehle@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While only Freescale Vybrid SoC has settings of GPIO capabilities done
by iomux controller, it is only a matter of GPIO controller driver
implementation for the rest of Freescale/NXP SoCs from iMX series.
As a practical example on GPIO request a pad function should be
switched to GPIO, but because this requires updates to all particular
iMX pinctrl drivers, for simplicity at the moment add only a proper
connection between shared pinctrl-imx and pinctrl/pinmux core, namely
.gpio_request_enable/.gpio_disable_free/.gpio_set_direction callbacks
should return success to a caller. This change allows to progress by
adding request/free callbacks into gpio-mxc.c driver.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
at91 used to set a default trigger type for GPIO interrupts in
order to cope with the old board files. These days are long gone,
and it all gets probed through DT.
Andras Szemzo reported that the Ethernet device on his board was
bailing to be probed, due to a conflict in interrupt trigger.
Surely enough, this is due to this default trigger still being
present, and turning this into a IRQ_TYPE_NONE fixes the issue.
Reported-by: Andras Szemzo <szemzo.andras@gmail.com>
Tested-by: Andras Szemzo <szemzo.andras@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch supports the {get,set}_io_voltage operations of SDHI.
This operates the POCCTRL0 register on R8A7796 SoC and makes 1.8v/3.3v
voltage switch.
Based on work by Takeshi Kihara and Wolfram Sang.
Cc: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The pinconf-generic code expects configurations with arguments to be
returned in a packed format in order to be displayed properly by
pinconf_generic_dump_one().
Reading /sys/kernel/debug/pinctrl/e6060000.pfc/pinconf-pins on
r8a7795/salvator-x now shows:
pin 101 (GP_3_5): output drive strength (9 mA), pin power source (3300 selector)
Instead of:
pin 101 (GP_3_5): output drive strength (0 mA), pin power source (0 selector)
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add MSIOF0/1 pin groups to the R8A7792 PFC driver.
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add QSPI pin groups to the R8A7792 PFC driver.
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
H3 has single PWM channel. The second PWM channel is not supported,
so the pinctrl function should be removed.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Check for pinctrl_ops and pinmux_ops structures that are only stored in the
pctlops field and the pmxops field, respectively, of a pinctrl_desc
structure. These fields are declared const, so pinctrl_ops and pinmux_ops
structures that have this property can be declared as const also.
The semantic patch that makes this change in the pinctrl_ops is as
follows. The pinmux_ops case is similar. (http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct pinctrl_ops i@p = { ... };
@ok@
identifier r.i;
struct pinctrl_desc e;
position p;
@@
e.pctlops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct pinctrl_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct pinctrl_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Check for pinctrl_ops and pinmux_ops structures that are only stored in the
pctlops field and the pmxops field, respectively, of a pinctrl_desc
structure. These fields are declared const, so pinctrl_ops and pinmux_ops
structures that have this property can be declared as const also.
The semantic patch that makes this change in the pinctrl_ops is as
follows. The pinmux_ops case is similar. (http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct pinctrl_ops i@p = { ... };
@ok@
identifier r.i;
struct pinctrl_desc e;
position p;
@@
e.pctlops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct pinctrl_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct pinctrl_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Check for pinctrl_ops and pinmux_ops structures that are only stored in the
pctlops field and the pmxops field, respectively, of a pinctrl_desc
structure. These fields are declared const, so pinctrl_ops and pinmux_ops
structures that have this property can be declared as const also.
The semantic patch that makes this change in the pinctrl_ops is as
follows. The pinmux_ops case is similar. (http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct pinctrl_ops i@p = { ... };
@ok@
identifier r.i;
struct pinctrl_desc e;
position p;
@@
e.pctlops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct pinctrl_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct pinctrl_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the function amd_gpio_irq_set_type, use the settings provided by
the BIOS,when the LevelTrig is Edge and activeLevel is HIGH, to configure
the GPIO registers. Ignore the settings from client.
Reviewed-by: Pankaj Sen <Pankaj.Sen@amd.com>
Signed-off-by:Nitesh Kumar Agrawal <Nitesh-kumar.Agrawal@amd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Just like the other member of the sunxi family, let's add a pinctrl table
for the muxing options.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A small subset of pins and functions are exposed. The selection of pins
and functions is driven by the development of OpenBMC[1] on the
AST2500 SoC, particularly around booting the IBM Witherspoon platform.
[1] https://github.com/openbmc/docs
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A subset of the pins and functions are exposed. The selection of
functions and pins is driven by the development of OpenBMC[1] on the
AST2400 SoC, particularly around booting the OpenPOWER Palmetto
development machine.
[1] https://github.com/openbmc/docs
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Aspeed SoCs typically provide more than 200 pins for GPIO and other
functions. The signal enabled on a pin is determined on a priority
basis, where a given pin can provide a number of different signal types.
In addition to the priority levels, the Aspeed pin controllers describe
the signal active on a pin by compound logical expressions involving
multiple operators, registers and bits. Some difficulty arises as a
pin's function bit masks for each priority level are frequently not the
same (i.e. we cannot just flip a bit to change from a high to low
priority signal), or even in the same register(s). Some configuration
bits affect multiple pins, while in other cases the signals for a bus
must each be enabled individually.
Together, these features give rise to some complexity in the
implementation. A more complete description of the complexities is
provided in the associated header file.
The patch doesn't implement pinctrl/pinmux/pinconf for any particular
Aspeed SoC, rather it adds the framework for defining pinmux
configurations.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
sd_emmc_a is used a controller for the SDIO modules. This adds the pin
configuration for the SDIO controller.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add initial support for the Pin Function Controller on the Renesas R-Car
M3-W SoC:
- Basic definitions,
- SCIF (serial) pins, groups and functions,
- SDHI pins, groups and functions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=AS9G
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.9-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Add support for R-Car M3-W
Add initial support for the Pin Function Controller on the Renesas R-Car
M3-W SoC:
- Basic definitions,
- SCIF (serial) pins, groups and functions,
- SDHI pins, groups and functions.
cat /sys/kernel/debug/pinctrl/${pinctrl}/pinconf-groups output is
hardly readable, if a pin group contains more than one pin the output
is glued and looks like this:
MX6Q_PAD_SD1_DAT0: 0x17071MX6Q_PAD_SD1_CMD: 0x17071MX6Q_PAD_SD1_CLK: 0x17071
Add two space indentation and a new line separator to improve
readability of the output.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Makefile currently controlling compilation of this code is:
drivers/pinctrl/sirf/pinctrl-sirf.o
--> drivers/pinctrl/sirf/Makefile:obj-y += pinctrl-sirf.o
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Rongjun Ying <rongjun.ying@csr.com>
Cc: Yuping Luo <yuping.luo@csr.com>
Cc: Barry Song <baohua@kernel.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Makefile currently controlling compilation of this code is:
drivers/pinctrl/sirf/pinctrl-atlas7.o
---> drivers/pinctrl/sirf/Makefile:obj-y += pinctrl-atlas7.o
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Barry Song <baohua@kernel.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/Kconfig:config PINCTRL_ROCKCHIP
drivers/pinctrl/Kconfig: bool
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-gpio@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/nomadik/Kconfig:config PINCTRL_NOMADIK
drivers/pinctrl/nomadik/Kconfig: bool "Nomadik pin controller driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
config PINCTRL_ABX500
bool "ST-Ericsson ABx500 family Mixed Signal Circuit gpio functions"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
Note that MODULE_ALIAS is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Makefile currently controlling compilation of this code is:
drivers/pinctrl/mediatek/pinctrl-mtk-common.o
---> drivers/pinctrl/mediatek/Makefile:obj-y += pinctrl-mtk-common.o
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
We don't replace module.h with init.h since the file doesn't need that.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Hongzhou Yang <hongzhou.yang@mediatek.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for PWM pins, for EE and AO domains.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
PG8, PG9 is said to be the CTS/RTS pins for UART1 according to the A23/33
datasheets. However, the function is wrongly named "uart2" in the pinctrl
driver. This patch fixes this by modifying them to be named "uart1".
Cc: stable@vger.kernel.org
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Bias and DU support for R-Car H3,
- Basic R-Car V2H support,
- Cleanups and fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1SFk
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.9-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.9
- Bias and DU support for R-Car H3,
- Basic R-Car V2H support,
- Cleanups and fixes.
The Cherryview GPIO controller has 8 or 16 wires connected to the I/O-APIC
which can be used directly by the platform/BIOS or drivers. One such wire
is used as SCI (System Control Interrupt) which ACPI depends on to be able
to trigger GPEs (General Purpose Events).
The pinctrl driver itself uses another IRQ resource which is wire OR of all
the 8 (or 16) wires and follows what BIOS has programmed to the IntSel
register of each pin.
Currently the driver masks all interrupts at probe time and this prevents
these direct interrupts from working as expected. The reason for this is
that some early stage prototypes had some pins misconfigured causing lots
of spurious interrupts.
We fix this by leaving the interrupt mask untouched. This allows SCI and
other direct interrupts work properly. What comes to the possible spurious
interrupts we switch the default handler to be handle_bad_irq() instead of
handle_simple_irq() (which was not correct anyway).
Reported-by: Yu C Chen <yu.c.chen@intel.com>
Reported-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the IR remote receiver to the AO domain devices.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A previous patch attempted to fix the pinmuxes for mfio 84 - 89, but it
omitted a change to pistachio_pin_group pistachio_groups, which results
in incorrect pll_lock signals being routed.
Apply the correct mux settings throughout the driver.
fixes: cefc03e599 ("pinctrl: Add Pistachio SoC pin control driver")
fixes: e9adb336d0 ("pinctrl: pistachio: fix mfio84-89 function description and pinmux.")
Cc: <stable@vger.kernel.org> # 4.4.x-
Signed-off-by: James Hartley <james.hartley@imgtec.com>
Reviewed-by: Sifan Naeem <Sifan.Naeem@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
of_match_device could return NULL, and so cause a NULL pointer
dereference later at line 1009:
pinctrl_data = match->data;
For fixing this problem, we use of_device_get_match_data(), this will
simplify the code a little by using a standard function for
getting the match data.
Reported-by: coverity (CID 1324136)
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Because chained_irq_enter() has already called chip->irq_mask() and
chip->irq_ack(), also chained_irq_exit() will call chip->irq_unmask(),
so it's not necessary to call chip->irq_*() here.
Signed-off-by: Perr Zhang <strongbox8@zoho.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[Hand-edited from whitespace damaged patch]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver originally supported more domains (register ranges) per
pinctrl device, but since commit 9dab1868ec ("pinctrl: amlogic: Make
driver independent from two-domain configuration") each device gets
assigned a single domain and we instantiate multiple pinctrl devices
in the DT.
Therefore, now the 'meson_domain' and 'meson_domain_data' structures
don't have any reason to exist and can be removed to make the model
simpler to understand. This commit doesn't change behavior.
Tested on a Odroid-C2.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds SDHI pins, groups and functions to R8A7796 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds SCIF{0,1,2,3,4,5} pins, groups and functions to R8A7796
SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds initial pinctrl driver to support for the R8A7796 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[uli: rebased on top of renesas-drivers]
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Only the DU parallel RGB output signals are included, HDMI and TCON pins
will be added in separate groups.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch allows to use the second parameter of gpio
specifier, which is used to specify whether the gpio is
active high or low.
Simply remove specific of_xlate callback() and of_gpio_n_cells
and use default one set by of_gpiochip_add() which allows
to use second parameter gpio specifier.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use of_property_read_bool to check for the existence of a property.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2,x;
@@
- if (of_get_property(e1,e2,NULL))
- x = true;
- else
- x = false;
+ x = of_property_read_bool(e1,e2);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The drivers don't really need to know which PMIC they're for, so
make a generic binding for them. This alleviates us from updating
the drivers every time a new PMIC comes out. It's still
recommended that we update the binding with new PMIC models and
always specify the specific model for the MPPs and gpios before
the generic compatible string in devicetree, but this at least
cuts down on adding more and more compatible strings to the
drivers until we actually need them.
Cc: <devicetree@vger.kernel.org>
Acked-by: "Ivan T. Ivanov" <iivanov.xz@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the SPDIF mux functionality to the pinctrl for the Allwinner A31
SoC.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On x86 builds the absense of <linux/io.h> makes static analyzer and compiler
unhappy which fails to build the driver.
CHECK drivers/pinctrl/intel/pinctrl-merrifield.c
drivers/pinctrl/intel/pinctrl-merrifield.c:518:17:
error: undefined identifier 'readl'
drivers/pinctrl/intel/pinctrl-merrifield.c:570:17:
error: undefined identifier 'readl'
drivers/pinctrl/intel/pinctrl-merrifield.c:575:9:
error: undefined identifier 'writel'
drivers/pinctrl/intel/pinctrl-merrifield.c:645:17:
error: undefined identifier 'readl'
CC drivers/pinctrl/intel/pinctrl-merrifield.o
drivers/pinctrl/intel/pinctrl-merrifield.c: In function ‘mrfld_pin_dbg_show’:
drivers/pinctrl/intel/pinctrl-merrifield.c:518:10:
error: implicit declaration of function ‘readl’
[-Werror=implicit-function-declaration]
value = readl(bufcfg);
^
drivers/pinctrl/intel/pinctrl-merrifield.c: In function ‘mrfld_update_bufcfg’:
drivers/pinctrl/intel/pinctrl-merrifield.c:575:2:
error: implicit declaration of function ‘writel’
[-Werror=implicit-function-declaration]
writel(value, bufcfg);
^
cc1: some warnings being treated as errors
Add header to the top of the module.
Fixes: 4e80c8f505 ("pinctrl: intel: Add Intel Merrifield pin controller support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the function amd_gpio_irq_enable() and
amd_gpio_direction_input(), remove the code which is setting
the default de-bounce time to 2.75ms.
The driver code shall use the same settings as specified in
BIOS. Any default assignment impacts TouchPad behaviour when
the LevelTrig is set to EDGE FALLING.
Cc: stable@vger.kernel.org
Reviewed-by: Ken Xue <Ken.Xue@amd.com>
Signed-off-by: Nitesh Kumar Agrawal <Nitesh-kumar.Agrawal@amd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's not necessary to unregister pin controller device registered
with devm_pinctrl_register() and using pinctrl_unregister() leads
to a double free.
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's not necessary to unregister pin controller device registered
with devm_pinctrl_register() and using pinctrl_unregister() leads
to a double free.
This is detected by Coccinelle semantic patch.
Fixes: e649f7ec8c ("pinctrl: meson: Use devm_pinctrl_register() for pinctrl registration")
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add DU pin groups to the R8A7792 PFC driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add VIN[0-5] pin groups to the R8A7792 PFC driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
[geert: Fix VI1_D14_G6_Y6 and VI1_D15_G7_Y7 pins]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This source file handles r8a7795 only, which is not the sole member of
the R-Car Gen3 family.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Add the EtherAVB pin groups to the R8A7792 PFC driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the PFC support for the R8A7792 SoC including pin groups for some
on-chip devices such as SCIF, INTC, and LBSC...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
[geert: s/LSBC/LBSC/]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The PORT_GP_CFG_<n>() macros take up more than 80 columns -- and not for
a good reason. Make the header file checkpatch.pl-proof at least in this
respect...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Implements pull-up and pull-down. On this SoC there is no simple mapping of
GP pins to bias register bits, so we need a table.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
New drivers:
- New driver for Oxnas pin control and GPIO. This ARM-based chipset
is used in a few storage (NAS) type devices.
- New driver for the MAX77620/MAX20024 pin controller portions.
- New driver for the Intel Merrifield pin controller.
New subdrivers:
- New subdriver for the Qualcomm MDM9615
- New subdriver for the STM32F746 MCU
- New subdriver for the Broadcom NSP SoC.
Cleanups:
- Demodularization of bool compiled-in drivers.
Apart from this there is just regular incremental improvements to
a lot of drivers, especially Uniphier and PFC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=po0g
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.8 kernel cycle.
Nothing stands out as especially exiting: new drivers, new subdrivers,
lots of cleanups and incremental features.
Business as usual.
New drivers:
- New driver for Oxnas pin control and GPIO. This ARM-based chipset
is used in a few storage (NAS) type devices.
- New driver for the MAX77620/MAX20024 pin controller portions.
- New driver for the Intel Merrifield pin controller.
New subdrivers:
- New subdriver for the Qualcomm MDM9615
- New subdriver for the STM32F746 MCU
- New subdriver for the Broadcom NSP SoC.
Cleanups:
- Demodularization of bool compiled-in drivers.
Apart from this there is just regular incremental improvements to a
lot of drivers, especially Uniphier and PFC"
* tag 'pinctrl-v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (131 commits)
pinctrl: fix pincontrol definition for marvell
pinctrl: xway: fix typo
Revert "pinctrl: amd: make it explicitly non-modular"
pinctrl: iproc: Add NSP and Stingray GPIO support
pinctrl: Update iProc GPIO DT bindings
pinctrl: bcm: add OF dependencies
pinctrl: ns2: remove redundant dev_err call in ns2_pinmux_probe()
pinctrl: Add STM32F746 MCU support
pinctrl: intel: Protect set wake flow by spin lock
pinctrl: nsp: remove redundant dev_err call in nsp_pinmux_probe()
pinctrl: uniphier: add Ethernet pin-mux settings
sh-pfc: Use PTR_ERR_OR_ZERO() to simplify the code
pinctrl: ns2: fix return value check in ns2_pinmux_probe()
pinctrl: qcom: update DT bindings with ebi2 groups
pinctrl: qcom: establish proper EBI2 pin groups
pinctrl: imx21: Remove the MODULE_DEVICE_TABLE() macro
Documentation: dt: Add new compatible to STM32 pinctrl driver bindings
includes: dt-bindings: Add STM32F746 pinctrl DT bindings
pinctrl: sunxi: fix nand0 function name for sun8i
pinctrl: uniphier: remove pointless pin-mux settings for PH1-LD11
...
Core changes:
- The big item is of course the completion of the character
device ABI. It has now replaced and surpassed the former
unmaintainable sysfs ABI: we can now hammer (bitbang)
individual lines or sets of lines and read individual lines
or sets of lines from userspace, and we can also register
to listen to GPIO events from userspace. As a tie-in we
have two new tools in tools/gpio: gpio-hammer and
gpio-event-mon that illustrate the proper use of the new
ABI. As someone said: the wild west days of GPIO are now
over.
- Continued to remove the pointless
ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB Kconfig symbols.
I'm patching hexagon, openrisc, powerpc, sh, unicore,
ia64 and microblaze. These are either ACKed by their
maintainers or patched anyways after a grace period and
no response from maintainers. Some archs (ARM) come in from
their trees, and others (x86) are still not fixed, so I
might send a second pull request to root it out later in
this merge window, or just defer to v4.9.
- The GPIO tools are moved to the tools build system.
New drivers:
- New driver for the MAX77620/MAX20024.
- New driver for the Intel Merrifield.
- Enabled PCA953x for the TI PCA9536.
- Enabled PCA953x for the Intel Edison.
- Enabled R8A7792 in the RCAR driver.
Driver improvements:
- The STMPE and F7188x now supports the .get_direction()
callback.
- The Xilinx driver supports setting multiple lines at
once.
- ACPI support for the Vulcan GPIO controller.
- The MMIO GPIO driver supports device tree probing.
- The Acer One 10 is supported through the _DEP ACPI
attribute.
Cleanups:
- A major cleanup of the OF/DT support code. It is way
easier to read and understand now, probably this improves
performance too.
- Drop a few redundant .owner assignments.
- Remove CLPS711x boardfile support: we are 100% DT.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NwcK
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.8 kernel cycle. The big
news is the completion of the chardev ABI which I'm very happy about
and apart from that it's an ordinary, quite busy cycle. The details
are below.
The patches are tested in linux-next for some time, patches to other
subsystem mostly have ACKs.
I got overly ambitious with configureing lines as input for IRQ lines
but it turns out that some controllers have their interrupt-enable and
input-enabling in orthogonal settings so the assumption that all IRQ
lines are input lines does not hold. Oh well, revert and back to the
drawing board with that.
Core changes:
- The big item is of course the completion of the character device
ABI. It has now replaced and surpassed the former unmaintainable
sysfs ABI: we can now hammer (bitbang) individual lines or sets of
lines and read individual lines or sets of lines from userspace,
and we can also register to listen to GPIO events from userspace.
As a tie-in we have two new tools in tools/gpio: gpio-hammer and
gpio-event-mon that illustrate the proper use of the new ABI. As
someone said: the wild west days of GPIO are now over.
- Continued to remove the pointless ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
Kconfig symbols. I'm patching hexagon, openrisc, powerpc, sh,
unicore, ia64 and microblaze. These are either ACKed by their
maintainers or patched anyways after a grace period and no response
from maintainers.
Some archs (ARM) come in from their trees, and others (x86) are
still not fixed, so I might send a second pull request to root it
out later in this merge window, or just defer to v4.9.
- The GPIO tools are moved to the tools build system.
New drivers:
- New driver for the MAX77620/MAX20024.
- New driver for the Intel Merrifield.
- Enabled PCA953x for the TI PCA9536.
- Enabled PCA953x for the Intel Edison.
- Enabled R8A7792 in the RCAR driver.
Driver improvements:
- The STMPE and F7188x now supports the .get_direction() callback.
- The Xilinx driver supports setting multiple lines at once.
- ACPI support for the Vulcan GPIO controller.
- The MMIO GPIO driver supports device tree probing.
- The Acer One 10 is supported through the _DEP ACPI attribute.
Cleanups:
- A major cleanup of the OF/DT support code. It is way easier to
read and understand now, probably this improves performance too.
- Drop a few redundant .owner assignments.
- Remove CLPS711x boardfile support: we are 100% DT"
* tag 'gpio-v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (67 commits)
MAINTAINERS: Add INTEL MERRIFIELD GPIO entry
gpio: dwapb: add missing fwnode_handle_put() in dwapb_gpio_get_pdata()
gpio: merrifield: Protect irq_ack() and gpio_set() by lock
gpio: merrifield: Introduce GPIO driver to support Merrifield
gpio: intel-mid: Make it depend to X86_INTEL_MID
gpio: intel-mid: Sort header block alphabetically
gpio: intel-mid: Remove potentially harmful code
gpio: rcar: add R8A7792 support
gpiolib: remove duplicated include from gpiolib.c
Revert "gpio: convince line to become input in irq helper"
gpiolib: of_find_gpio(): Don't discard errors
gpio: of: Allow overriding the device node
gpio: free handles in fringe cases
gpio: tps65218: Add platform_device_id table
gpio: max77620: get gpio value based on direction
gpio: lynxpoint: avoid potential warning on error path
tools/gpio: add install section
tools/gpio: move to tools buildsystem
gpio: intel-mid: switch to devm_gpiochip_add_data()
gpio: 74x164: Use spi_write() helper instead of open coding
...
On Marvell mv88f6180 with pin control driver one can not use multi
purpose pins 35 through 44.
I'm using this controller on an embedded board and i found that the
pin multiplexing is not the same as in the hardware spezification.
This patch alters the pin description so that mpp pins 0 to 19 as well
as 35 to 44 are usable.
Pin settings i used can be found here:
http://www.marvell.com/embedded-processors/kirkwood/assets/HW_88F6180_OpenSource.pdf
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Reviewed-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A typo in the previous commit to this file needs fixing.
Cc: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 6b4316aece ("pinctrl: xway: Change structure initialisation to c99 style")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit b8c2b10a9b.
This patch was in my queue at the same time that a conversion of
the same driver from bool --> tristate was pending and merged.
That is commit 337ea0fb15 ("pinctrl: Turn AMD support to tristate")
Normally the conflict would show up in the build coverage I do,
however in this case an avoidable instance of linux/module.h in
linux/gpio/driver.h (!) causes the build failure to be masked and
instead the tristate gets built-in even for selected "=m".
In working on removing module.h from driver.h this issue was then
revealed (along with other implicit module.h assumptions in gpio,
and mfd -- which will be fixed separately.)
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The iProc GPIO controller is shared among multiple iProc based SoCs.
In the NSP integration, the drive strength pinctrl function is
disabled. In the integration of Stingray, pinctrl is handled by another
block and this GPIO controller is solely used as a GPIO controller, and
therefore should not be registered to the pinconf framework
This patch introduces new SoC specific compatible strings
"brcm,iproc-nsp-gpio" for NSP with drive strength feature disabled and
"brcm,iproc-stingray-gpio" for Stingray with all PINCONF features
disabled
This patch is developed based on the initial work from Yendapally
Reddy Dhananjaya <yendapally.reddy@broadcom.com> who attempted to
disable drive strength configuration for the iProc based NSP chip. In
addition, Pramod Kumar <pramod.kumar@broadcom.com> also contributed to
make the support more generic across all currently supported PINCONF
functions in the iProc GPIO/PINCONF driver
Signed-off-by: Pramod Kumar <pramodku@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Building without CONFIG_OF gives us these warnings for the broadcom
pinctrl drivers:
drivers/pinctrl/bcm/pinctrl-nsp-mux.c:356:20: error: 'pinconf_generic_dt_node_to_map_group' undeclared here (not in a function)
drivers/pinctrl/bcm/pinctrl-cygnus-mux.c:739:20: error: 'pinconf_generic_dt_node_to_map_group' undeclared here (not in a function)
The function is only available when CONFIG_OF is set, so we should add
a Kconfig dependency for both drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: cc4fa83f66 ("pinctrl: nsp: add pinmux driver support for Broadcom NSP SoC")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch which adds STM32F746 pinctrl and GPIO support, relies on the
generic STM32 pinctrl driver.
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It seems intel_gpio_irq_wake() misses lock protection against I/O flow.
Use spin lock here as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In case of error, the function pinctrl_register() returns
NULL not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After some digging around I found documentation (!) of the APQ8060
EBI2 pin groups. It turns out I first need to split the group in
two: ebi2cs and ebi2 proper. The chip select pins are kind of
orthogonal to the other EBI2 pins since CS1B and CS2B can be muxed
over address bits 7 and 6 (don't know why, but they can). This
is good to fix up before we add users.
Also found what the "holes" in the assignment all the way up to
gpio158 was actually for.
All mux documentation comes from "Snapdragon(TM) S3 APQ8060-based
DragonBoard(TM) GPIO User Guide Rev. E August 10, 2012", published
by Bsquare Corporation.
As the documentation seems a bit hard to come by I put some comments
in the group definitions so that it is clear to all readers what
is going on here and what the lines are used for.
Cc: Björn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit e2756baa42 ("pinctrl: imx21: make it explicitly non-modular")
missed the removal of the MODULE_DEVICE_TABLE() macro causing the
following build error:
drivers/pinctrl/freescale/pinctrl-imx21.c:328:1: error: data definition has no type or storage class [-Werror]
MODULE_DEVICE_TABLE(of, imx21_pinctrl_of_match);
,so remove the macro to fix this problem.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In sun4/5/6/7i, all the pin function related to NAND0 controller is
named "nand0". However, in sun8i, some of the functions are named as
"nand". This patch renamed them to "nand0", for the consistency.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This SoC has no SD card controller. Nor does it have USB port3.
These pin-mux settings have no point.
Fixes: 70f2f9c4cf ("pinctrl: uniphier: add UniPhier PH1-LD11 pinctrl driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support to mux in the second external bus interface as
follows:
- CS1 and CS2 on GPIO39 and GPIO40 as func 2
- ADDR_7 thru ADDR_0 on GPIO123 thru GPIO130 as func 1
- CS4, CS3 and CS0 on GPIO132, GPIO133, GPIO134 as func 1
- DATA_15 thru DATA_0 on GPIO135 thru GPIO150 as func 1
- OE on GPIO151 as func 1
- ADV on GPIO153 as func 1
- WE on GPIO157 as func 1
This external bus is used on the APQ8060 Dragonboard to connect
an external SMSC9211 ethernet adapter, but there are many other
usecases for the EBI2.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Björn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The msm8974 pinctrl variant has a couple USB HSIC "glue"
registers that let us mux between the pinctrl register settings
or the HSIC core settings for the HSIC pins (gpio 144 and gpio
145). Support this method of operation by adding hsic_data and
hsic_strobe pins that can select between hsic_ctl and gpio
functions. This allows us to toggle the hsic pin configuration
over to the HSIC core at runtime.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The function selection bitfield is not always 3 bits wide.
Sometimes it is 4 bits wide. Let's use the npins struct member to
determine how many bits wide the function selection bitfield is
so we clear the correct amount of bits in the register while
remuxing the pins.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to support the Qualcomm MDM9615 SoC, add support for the TLMM
using the Qualcomm pinctrl generic driver.
Note: the pinctrl is partial, need Documentation to complete all the groups.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
of_find_node_by_name does an of_node_get on its return value,
so an of_node_put is needed on this value before the corresponding
variable goes out of scope.
The Coccinelle semantic patch used to make this change is as follows:
@@
struct device_node *n;
struct device_node *n1;
statement S;
identifier f;
expression E;
constant C;
@@
n = of_find_node_by_name(...)
...
if (!n) S
... when != of_node_put(n)
when != n1 = f(n,...)
when != E = n
when any
when strict
(
+ of_node_put(n);
return -C;
|
of_node_put(n);
|
n1 = f(n,...)
|
E = n
|
return ...;
)
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the initial support of the Broadcom NSP pinmux driver.
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Voltage switching support for R-Car H3,
- DRIF pin support for R-Car H3,
- Cleanups and fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z1/q
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.8-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.8
- Voltage switching support for R-Car H3,
- DRIF pin support for R-Car H3,
- Cleanups and fixes.
This driver adds pinctrl support for Intel Merrifield. The IP block which is
called Family-Level Interface Shim is a separate entity in SoC. The GPIO driver
(gpio-intel-mid.c) will be updated accordingly to support pinctrl interface.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_MXS
drivers/pinctrl/freescale/Kconfig: bool
...meaning that it currently is not being built as a module by anyone.
It also doesn't have any modular functionality, so it doesn't need
module.h included at all.
What it does have is an exported function that was used as a shared
".remove" by other drivers, but those use cases (imx23 and imx28)
are now gone, and hence this can disappear as well.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX28
drivers/pinctrl/freescale/Kconfig: bool
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX23
drivers/pinctrl/freescale/Kconfig: bool
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init wasn't actually used by this driver, the init
ordering remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_VF610
drivers/pinctrl/freescale/Kconfig: bool "Freescale Vybrid VF610 pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init wasn't in use by this driver, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX7D
drivers/pinctrl/freescale/Kconfig: bool "IMX7D pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Anson Huang <Anson.Huang@freescale.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX6UL
drivers/pinctrl/freescale/Kconfig: bool "IMX6UL pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Anson Huang <Anson.Huang@freescale.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX6SX
drivers/pinctrl/freescale/Kconfig: bool "IMX6SX pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Anson Huang <Anson.Huang@freescale.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX6SL
drivers/pinctrl/freescale/Kconfig: bool "IMX6SL pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX6Q
drivers/pinctrl/freescale/Kconfig: bool "IMX6Q/DL pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We don't replace module.h with init.h since the file already has that.
But we do add export.h since this file uses the global THIS_MODULE.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Dong Aisheng <dong.aisheng@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX6Q
drivers/pinctrl/freescale/Kconfig: bool "IMX6Q/DL pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX53
drivers/pinctrl/freescale/Kconfig: bool "IMX53 pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Dong Aisheng <dong.aisheng@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX51
drivers/pinctrl/freescale/Kconfig: bool "IMX51 pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Dong Aisheng <dong.aisheng@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX50
drivers/pinctrl/freescale/Kconfig: bool "IMX50 pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX35
drivers/pinctrl/freescale/Kconfig: bool "IMX35 pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Dong Aisheng <dong.aisheng@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX27
drivers/pinctrl/freescale/Kconfig: bool "IMX27 pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX25
drivers/pinctrl/freescale/Kconfig: bool "IMX25 pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this driver, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Denis Carikli <denis@eukrea.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX21
drivers/pinctrl/freescale/Kconfig: bool "i.MX21 pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/freescale/Kconfig:config PINCTRL_IMX1
drivers/pinctrl/freescale/Kconfig: bool "IMX1 pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
None of these files have anything modular in them, so they
don't need to be bringing in module.h and all its dependencies.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinconf-generic.h file exposes functions for creating generic mappings
but it does not expose a function for freeing the mappings. Add a function
for freeing generic mappings.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix plt clock 3, 4 and 5 pins, which were not in the proper order.
Signed-off-by: Cristina Ciocan <cristina.ciocan@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now we have PINMUX_SINGLE(). Let's use it instead of PINMUX_IPSR_NOGP()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The rockchip_irq_gc_mask_set_bit() function is not exported our used
outside of ppinctrl-rockchip.c so fix the following sparse error by
making it static:
drivers/pinctrl/pinctrl-rockchip.c:2010:6: warning:
symbol 'rockchip_irq_gc_mask_set_bit' was not declared.
Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit 8b2b3dcb34.
Commit 546c6d7930 (pinctrl: digicolor: make it explicitly non-modular) removed
the platform_get_drvdata() call, so platform_set_drvdata() is no longer needed.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
config PINCTRL_AS3722
bool "Pinctrl and GPIO driver for ams AS3722 PMIC"
...meaning that it currently is not being built as a module by anyone.
During an audit for non-modular drivers using modular infrastructure
this driver showed up.
But rather than demodularize it, Laxman indicated that it would be
prefereable to instead convert the driver option to tristate.
This does that, and confirms that it will compile and modpost as
such. However, since I do not have the hardware to confirm that
no new runtime issues exist when modular, that remains untested.
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
config PINCTRL_PALMAS
bool "Pinctrl driver for the PALMAS Series MFD devices"
...meaning that it currently is not being built as a module by anyone.
During an audit for non-modular drivers using modular infrastructure
this driver showed up.
But rather than demodularize it, Laxman indicated that it would be
prefereable to instead convert the driver option to tristate.
This does that, and confirms that it will compile and modpost as
such. However, since I do not have the hardware to confirm that
no new runtime issues exist when modular, that remains untested.
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
I got below build error:
ERROR: "tegra_xusb_padctl_legacy_probe"
[drivers/phy/tegra/phy-tegra-xusb.ko] undefined!
with below build configuration:
CONFIG_ARCH_TEGRA=y
CONFIG_PINCTRL_TEGRA_XUSB=y
CONFIG_PHY_TEGRA_XUSB=y
The problem is below line in drivers/pinctrl/Makefile
obj-$(CONFIG_PINCTRL_TEGRA) += tegra/
So even CONFIG_PINCTRL_TEGRA_XUSB=y is set, kbuild still does not compile
the code in drivers/pinctrl/tegra folder if !CONFIG_PINCTRL_TEGRA.
phy-tegra-xusb.c does not use any symbol from pinctrl-tegra.c,
so build pinctrl-tegra.c only when CONFIG_PINCTRL_TEGRA is set.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With many repeated suspend resume cycles, the pin specific wakeirq
may not always work on omaps. This is because the write to enable the
pin interrupt may not have reached the device over the interconnect
before suspend happens.
Let's fix the issue with a flush of posted write with a readback.
Cc: stable@vger.kernel.org
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some PINs do not have a MUX register, it is not an error.
It is necessary to allow the continuation of the PINs configuration,
otherwise the whole PIN-group will be configured incorrectly.
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This allows to remove the .remove() callback, and all functions and data
it needed for its own bookkeeping.
Suggested-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The Renesas Pin Function Controller uses two header files:
- sh_pfc.h, for use by both core code and SoC-specific drivers,
- core.h, for internal use by the core code only.
Several SoC-specific drivers include core.h, as they need the sh_pfc
structure, which is passed explicitly to the various SoC-specific
callbacks, and used there.
Hence move its definition from core.h to sh_pfc.h, and remove the
inclusion of core.h from all SoC-specific files.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
With C=1:
drivers/pinctrl/sh-pfc/pfc-emev2.c:1695:30: warning: symbol 'emev2_pinmux_info' was not declared. Should it be static?
drivers/pinctrl/sh-pfc/pfc-r8a7779.c:3888:30: warning: symbol 'r8a7779_pinmux_info' was not declared. Should it be static?
Note that there are more warnings on SH.
The sh_pfc_soc_info structure is defined in sh_pfc.h, while all forward
declarations for the SoC-specific versions are in core.h.
Move the forward declarations from core.h to sh_pfc.h to fix this.
Reported-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
When pinctrl_get() is called for a device, it will return a valid handle
even if the device itself has no pinctrl state entries defined in
device-tree. This is caused by the function pinctrl_dt_to_map() which
will return success even if the first pinctrl state, 'pinctrl-0', is not
found in the device-tree node for a device.
According to the pinctrl device-tree binding documentation, pinctrl
states must be numbered starting from 0 and so 'pinctrl-0' should always
be present if a device uses pinctrl and therefore, if 'pinctrl-0' is not
present it seems valid that we should not return a valid pinctrl handle.
Fix this by returning an error code if the property 'pinctrl-0' is not
present for a device.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinctrl-intel needs to use request_irq() instead of chained interrupt
handling because it shares the interrupt with multiple GPIO host
controllers found on Intel CPUs. In -rt all such interrupts are forced to
run in thread context which triggers following warning:
WARNING: CPU: 0 PID: 530 at kernel/irq/handle.c:151 handle_irq_event_percpu+0x23d/0x240
irq 348 handler irq_default_primary_handler+0x0/0x10 enabled interrupts
Modules linked in:
CPU: 0 PID: 530 Comm: irq/14-INT3452: Not tainted 4.6.2-rt5 #1060
0000000000000000 ffff88007a257c98 ffffffff812d8494 ffff88007a257ce8
0000000000000000 ffff88007a257cd8 ffffffff8105e554 000000977a257d90
ffff88007a37a380 000000000000015c 0000000000000002 0000000000000000
Call Trace:
[<ffffffff812d8494>] dump_stack+0x4f/0x6b
[<ffffffff8105e554>] __warn+0xe4/0x100
[<ffffffff8105e5bf>] warn_slowpath_fmt+0x4f/0x60
[<ffffffff810b18f0>] ? __synchronize_hardirq+0x60/0x60
[<ffffffff810b17fd>] handle_irq_event_percpu+0x23d/0x240
[<ffffffff810b1862>] handle_irq_event+0x62/0x90
[<ffffffff810b4e1f>] handle_edge_irq+0x8f/0x190
[<ffffffff810b0d82>] generic_handle_irq+0x22/0x30
[<ffffffff81307abc>] intel_gpio_irq+0xdc/0x150
[<ffffffff810b2293>] irq_forced_thread_fn+0x23/0x70
[<ffffffff810b250b>] irq_thread+0x13b/0x1d0
[<ffffffff8167b844>] ? __schedule+0x2e4/0x5a0
[<ffffffff810b2270>] ? irq_finalize_oneshot.part.37+0xd0/0xd0
[<ffffffff810b25a0>] ? irq_thread+0x1d0/0x1d0
[<ffffffff810b23d0>] ? wake_threads_waitq+0x30/0x30
[<ffffffff8107e624>] kthread+0xd4/0xf0
[<ffffffff8167ec27>] ? _raw_spin_unlock_irq+0x17/0x40
[<ffffffff8167f592>] ret_from_fork+0x22/0x40
[<ffffffff8107e550>] ? kthread_worker_fn+0x190/0x190
The handle_irq_event_* functions (and I suppose generic_handle_irq()) is
expected to be called with interrupts disabled and they rightfully complain
here because we run in thread context with interrupts enabled.
Fix this by adding IRQF_NO_THREAD flag when the master interrupt is
requested. This prevents forced threading of the interrupt used by the GPIO
host controllers.
Reported-by: Kim Tatt Chuah <kim.tatt.chuah@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When running -rt kernel and GPIO interrupt happens we get following
BUG: sleeping function called from invalid context at kernel/locking/rtmutex.c:931
in_atomic(): 1, irqs_disabled(): 0, pid: 530, name: irq/14-INT3452:
Preemption disabled at:[<ffffffff810b4dab>] handle_edge_irq+0x1b/0x190
CPU: 0 PID: 530 Comm: irq/14-INT3452: Not tainted 4.6.2-rt5 #1060
0000000000000000 ffff88007a257d58 ffffffff812d8494 0000000000000000
ffff88017a330000 ffff88007a257d78 ffffffff81083a11 ffff88007a252430
ffff88007a252430 ffff88007a257d90 ffffffff8167ef20 000000000000001a
Call Trace:
[<ffffffff812d8494>] dump_stack+0x4f/0x6b
[<ffffffff81083a11>] ___might_sleep+0xe1/0x160
[<ffffffff8167ef20>] rt_spin_lock+0x20/0x50
[<ffffffff81308c6d>] intel_gpio_irq_ack+0x2d/0x80
[<ffffffff810b4e0b>] handle_edge_irq+0x7b/0x190
[<ffffffff810b0d82>] generic_handle_irq+0x22/0x30
[<ffffffff81307abc>] intel_gpio_irq+0xdc/0x150
[<ffffffff810b2293>] irq_forced_thread_fn+0x23/0x70
[<ffffffff810b250b>] irq_thread+0x13b/0x1d0
[<ffffffff8167b844>] ? __schedule+0x2e4/0x5a0
[<ffffffff810b2270>] ? irq_finalize_oneshot.part.37+0xd0/0xd0
[<ffffffff810b25a0>] ? irq_thread+0x1d0/0x1d0
[<ffffffff810b23d0>] ? wake_threads_waitq+0x30/0x30
[<ffffffff8107e624>] kthread+0xd4/0xf0
[<ffffffff8167ec27>] ? _raw_spin_unlock_irq+0x17/0x40
[<ffffffff8167f592>] ret_from_fork+0x22/0x40
[<ffffffff8107e550>] ? kthread_worker_fn+0x190/0x190
The reason why this happens is because intel_gpio_irq_ack() is called with
desc->lock raw_spinlock locked which cannot sleep but our normal spinlock
(which is converted to rtmutex in -rt) is allowed to sleep. This causes
might_sleep() to trigger.
Fix this by converting the normal spinlock to a raw_spinlock.
Reported-by: Kim Tatt Chuah <kim.tatt.chuah@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These are input-only pins. They do not support drive controlling
in the first place.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to the hardware document, setting the drive control is
prohibited for these pins (N-channel Open Drain pins). Set their
drive control attribute to "fixed".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is to cater the need for non-ACPI system whereby
a platform device has to be created in order to bind
with the Apollo Lake Pinctrl GPIO platform driver.
Signed-off-by: Tan Jui Nee <jui.nee.tan@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The recently added max77620 driver fails to build when CONFIG_PINMUX
is not set:
pinctrl/pinctrl-max77620.c:272:21: error: variable 'max77620_pinmux_ops' has initializer but incomplete type
static const struct pinmux_ops max77620_pinmux_ops = {
^~~~~~~~~~
pinctrl/pinctrl-max77620.c:273:2: error: unknown field 'get_functions_count' specified in initializer
This adds the Kconfig 'select' statement that was clearly meant
to be there and is used in all other pinmux drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When building with 'make W=1', we get harmless warnings about
five drivers in drivers/pinctrl, which all contain a copy of
the same line:
drivers/pinctrl/freescale/pinctrl-imx1-core.c:160:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
This replaces the somewhat nonstandard 'static const inline'
with 'static inline const', which has the same meaning but
does not cause this warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The strucuture 'max77620_cfg_param' is defined but never used by the
max77620 driver. Remove this structure definition.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pin config get/set handlers for pin groups were previously not
implemented by this driver. The pin_config_group_set is
particularly useful for applying a common config setting to all
pins in a specified group with a single call, without the caller
needing to reference each individual pin by name.
Signed-off-by: Dan O'Donovan <dan@emutex.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On some CHV platforms, we need an option to configure the
open-drain setting for these pins. This adds support for the
PIN_CONFIG_DRIVE_PUSH_PULL and PIN_CONFIG_DRIVE_OPEN_DRAIN to
disable/enable open-drain mode for a specific pin.
Signed-off-by: Dan O'Donovan <dan@emutex.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Due to a silicon issue on the Atom X5-Z8000 "Cherry Trail" processor
series, a common lock must be used to prevent concurrent accesses
across the 4 GPIO controllers managed by this driver.
See Intel Atom Z8000 Processor Series Specification Update
(Rev. 005), errata #CHT34, for further information.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dan O'Donovan <dan@emutex.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PM8058 is found in connection to the APQ8060 on the APQ8060
Dragonboard. Works the same as all others, just add the compatible
string for this variant.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With C=1:
drivers/pinctrl/sh-pfc/pfc-sh7757.c:1613:9: warning: Initializer entry defined twice
drivers/pinctrl/sh-pfc/pfc-sh7757.c:1628:9: also defined here
Remove the duplicate initializer to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Replace the in order struct initialisation style with explicit field
style.
The Coccinelle semantic patch used to make this change is as follows:
@decl@
identifier i1,fld;
type T;
field list[n] fs;
@@
struct i1 {
fs
T fld;
...};
@@
identifier decl.i1,i2,decl.fld;
expression e;
position bad.p, bad.fix;
@@
struct i1 i2@p = { ...,
+ .fld = e
- e@fix
,...};
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The array u300_pmx_registers is not declared or used outside
of the driver, so make it static to avoid the following warning:
drivers/pinctrl/pinctrl-u300.c:673:11: warning: symbol 'u300_pmx_registers' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
drivers/pinctrl/bcm/Makefile properly builds individual drivers based on
their respective Kconfig symbols. ARCH_BCM is currently a menuconfig
option from arch/arm/mach-bcm/Kconfig, which is fine, but prevents ARM64
platforms which do not have such menuconfig option from building their
pinctrl drivers, so let's get rid of that dependency.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are five functions in the driver that are defined but
only used locally. Since these are not used in the current
kernel, delete them to avoid the following warnings:
drivers/pinctrl/nomadik/pinctrl-nomadik.c:1036:6: warning: symbol 'nmk_gpio_clocks_enable' was not declared. Should it be static?
drivers/pinctrl/nomadik/pinctrl-nomadik.c:1050:6: warning: symbol 'nmk_gpio_clocks_disable' was not declared. Should it be static?
drivers/pinctrl/nomadik/pinctrl-nomadik.c:1073:6: warning: symbol 'nmk_gpio_wakeups_suspend' was not declared. Should it be static?
drivers/pinctrl/nomadik/pinctrl-nomadik.c:1094:6: warning: symbol 'nmk_gpio_wakeups_resume' was not declared. Should it be static?
drivers/pinctrl/nomadik/pinctrl-nomadik.c:1120:6: warning: symbol 'nmk_gpio_read_pull' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/Kconfig:config PINCTRL_AT91PIO4
drivers/pinctrl/Kconfig: bool "AT91 PIO4 pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/Kconfig:config PINCTRL_DIGICOLOR
drivers/pinctrl/Kconfig: bool
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
config PINCTRL_ZYNQ
bool "Pinctrl driver for Xilinx Zynq"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
config PINCTRL_AMD
bool "AMD GPIO pin control"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: Ken Xue <Ken.Xue@amd.com>
Cc: Jeff Wu <Jeff.Wu@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
config PINCTRL_LPC18XX
bool "NXP LPC18XX/43XX SCU pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/Kconfig:config PINCTRL_AT91
drivers/pinctrl/Kconfig: bool "AT91 pinctrl driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not being used in this driver, we don't need
to be concerned with initcall ordering changes when removing it.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
config PINCTRL_BAYTRAIL
bool "Intel Baytrail GPIO pin control"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init() was already not in use in this driver, we don't
have any concerns with init ordering changes here.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All known hardware being able to switch voltages has the same POCCTRL
register. So, factor out the common code to the core and keep only
the pin-to-bit mapping SoC specific. Convert the only user, r8a7790.
In case POCCTRL should ever get more complex (more voltages to select?),
we should probably switch over to a describing array like drive strength
does currently.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The atmel_pctl_find_group_by_pin() and the atmel_pinctrl_remove()
functions are not exported, so fix the warnings about these
being exported without definitions by making them static.
drivers/pinctrl/pinctrl-at91-pio4.c:424:20: warning: symbol 'atmel_pctl_find_group_by_pin' was not declared. Should it be static?
drivers/pinctrl/pinctrl-at91-pio4.c:1077:5: warning: symbol 'atmel_pinctrl_remove' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixup warnings from functions that are not exported and
therefore should be marked static. Fixes:
drivers/pinctrl/bcm/pinctrl-nsp-gpio.c:461:5:
warning: symbol 'nsp_pin_config_group_get' was not declared.
Should it be static?
drivers/pinctrl/bcm/pinctrl-nsp-gpio.c:467:5:
warning: symbol 'nsp_pin_config_group_set' was not declared.
Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
My mistake in the initial support patches.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
An irq which is a wake up source maybe masked unexpectedly if the wake
up source irq was triggered after pinctrl irqchip suspend and before
suspend_device_irqs finished.
Use *_noirq callbacks to guarantee pinctrl irqchip suspend would be
called after suspend_devices_irqs.
Signed-off-by: hongkun.cao <hongkun.cao@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Avoid a gpiochip_free() and use standard functions.
Cc: John Crispin <blogic@openwrt.org>
Cc: Pramod Gurav <pramod.gurav@smartplayin.com>
Cc: Martin Schiller <mschiller@tdt.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename pinctrl_utils_dt_free_map to pinctrl_utils_free_map, introduced in
d32f7fd3bb ("pinctrl: Rename pinctrl_utils_dt_free_map to pinctrl_utils_free_map")
but not reported into oxnas driver.
Fixes: 611dac1e48 ("pinctrl: Add Oxford Semiconductor OXNAS pinctrl and gpio driver")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently, the UniPhier pinctrl driver itself is a syscon, but it
turned out much more reasonable to make it a child node of a syscon
because our syscon node consists of a bunch of system configuration
registers, not only pinctrl, but also phy, and misc registers.
It is difficult to split the node.
To allow to migrate to the new DT structure, this commit adds new
compatible strings to not disturb the existing DT. After a while,
the old binding will be removed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is needed to get access to UniPhier System Bus (external bus).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These pins do not support pin-muxing, but it is useful to support
pin configuration for them.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
PH1-LD4 and PH1-sLD8 SoCs have pins that support pin configuration
(pin biasing, drive strength control), but not pin-muxing.
Allow to fill the mux value table with -1 for those pins; pins with
mux value -1 will be skipped in the pin-mux set function. The mux
value type should be changed from "unsigned" to "int" in order to
accommodate -1 as a special case.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Upcoming new pinctrl drivers for PH1-LD11 and PH-LD20 support input
signal gating for each pin. (While, existing ones only support it
per pin-group.) This commit updates the core part for that.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The core part of the UniPhier pinctrl driver needs to support a new
capability for upcoming UniPhier ARMv8 SoCs. This sometimes happens
because pinctrl drivers include really SoC-specific stuff.
This commit intends to tidy up SoC-specific parameters of the existing
drivers before adding the new one. Having just one flag would be
better than adding a new struct member every time a new SoC-specific
capability comes up.
At this time, there is one flag, UNIPHIER_PINCTRL_CAPS_DBGMUX_SEPARATE.
This capability (I'd say rather quirk) was added for PH1-Pro4 and
PH1-Pro5 as requirement from a customer. For those SoCs, one pin-mux
setting is controlled by the combination of two separate registers; the
LSB bits at register offset (8 * N) and the MSB bits at (8 * N + 4).
Because it is impossible to update two separate registers atomically,
the LOAD_PINCTRL register should be set in order to make the pin-mux
settings really effective.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Unfortunately, the pin number of the new SoC, PH1-LD11, is not
contiguous. The base frame work must be adjusted to support the new
SoC pinctrl driver. The pin_desc_get() exploits radix-tree for pin
look-up, so it works more efficiently with sparse pin space.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The new ARMv8 SoC, PH1-LD20, supports more fine-grained drive
strength control. Drive strength of some pins are controlled by
3-bit width registers (8-level granularity).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The new ARMv8 SoC, PH1-LD20, supports more fine-grained drive
strength control. Some of the configuration registers on it have
3-bit width.
The feature will be supported in the next commit, but a problem is
that macro names are getting longer and longer in the current naming
scheme.
Before moving forward, this commit renames macros as follows:
UNIPHIER_PIN_DRV_4_8 -> UNIPHIER_PIN_DRV_1BIT
UNIPHIER_PIN_DRV_8_12_16_20 -> UNIPHIER_PIN_DRV_2BIT
UNIPHIER_PIN_DRV_FIXED_4 -> UNIPHIER_PIN_DRV_FIXED4
UNIPHIER_PIN_DRV_FIXED_5 -> UNIPHIER_PIN_DRV_FIXED5
UNIPHIER_PIN_DRV_FIXED_8 -> UNIPHIER_PIN_DRV_FIXED8
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently, every SoC driver defines struct pinctrl_desc statically,
i.e. it consumes memory footprint even if it is not probed.
In multi-platform, many pinctrl drivers are linked (generally as
built-in objects), although only one of them is actually used.
So, it is reasonable to allocate memory dynamically where possible.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Every SoC driver sets the same name for struct pinctrl_desc and
platform_driver. The common probe function can set desc->name
instead of duplicating strings in each SoC driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The owner of the struct pinctrl_desc matches that of platform_driver.
Set it in the common probe function.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These pin tables were generated by parsing hardware documents with
a script, but the script had a bug. Fix the register offsets.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make function/variable names match the file names for consistency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To i.MX7D, there are two iomux controllers, iomuxc and iomuxc_lpsr.
They should not share one pin controller descriptor, otherwise
the value filled into imx_pinctrl_desc when probing the first
iomux controller will be overridden when probing the second one.
In this patch, discard the static allcoated imx_pinctrl_desc and
switch to dynamically allcate pin controller descriptor for each
iomux controller.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add EE domain pins for ethernet interface.
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add EE domain pins for UART A, B & C.
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Andy Shevchenko