While we disable runtime PM and with that display power well support if
the DMC firmware isn't loaded, we still want to disable power wells
during system suspend and driver unload. So drop/reacquire the
corresponding power refcount during suspend/resume and driver unloading.
This also means we have to check if DMC is not loaded and skip enabling
DC states in the power well code.
v2:
- Reuse intel_csr_ucode_suspend() in intel_csr_ucode_fini() instead of
opencoding the former. (Chris)
- Add docbook comment to the public resume and suspend functions.
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1460980101-14713-1-git-send-email-imre.deak@intel.com
The driver's VDD on/off logic assumes that whenever the VDD is on we
also hold an AUX power domain reference. Since BIOS can leave the VDD on
during booting and resuming and on DDI platforms we won't take a
corresponding power reference, the above assumption won't hold on those
platforms and an eventual delayed VDD off work will do an extraneous AUX
power domain put resulting in a refcount underflow. Fix this the same
way we did this for non-DDI DP encoders:
commit 6d93c0c417 ("drm/i915: fix VDD state tracking after system
resume")
At the same time call the DP encoder suspend handler the same way as the
non-DDI DP encoders do to flush any pending VDD off work. Leaving the
work running may cause a HW access where we don't expect this (at a point
where power domains are suspended already).
While at it remove an unnecessary function call indirection.
This fixed for me AUX refcount underflow problems on BXT during
suspend/resume.
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: stable@vger.kernel.org
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460963062-13211-4-git-send-email-imre.deak@intel.com
During system resume we depended on pci_enable_device() also putting the
device into PCI D0 state. This won't work if the PCI device was already
enabled but still in D3 state. This is because pci_enable_device() is
refcounted and will not change the HW state if called with a non-zero
refcount. Leaving the device in D3 will make all subsequent device
accesses fail.
This didn't cause a problem most of the time, since we resumed with an
enable refcount of 0. But it fails at least after module reload because
after that we also happen to leak a PCI device enable reference: During
probing we call drm_get_pci_dev() which will enable the PCI device, but
during device removal drm_put_dev() won't disable it. This is a bug of
its own in DRM core, but without much harm as it only leaves the PCI
device enabled. Fixing it is also a bit more involved, due to DRM
mid-layering and because it affects non-i915 drivers too. The fix in
this patch is valid regardless of the problem in DRM core.
v2:
- Add a code comment about the relation of this fix to the freeze/thaw
vs. the suspend/resume phases. (Ville)
- Add a code comment about the inconsistent ordering of set power state
and device enable calls. (Chris)
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: stable@vger.kernel.org
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460979954-14503-1-git-send-email-imre.deak@intel.com
The workaround added in
commit c6782b76d3 ("drm/i915/gen9: Reset secondary power well
requests left on by DMC/KVMR")
needs to be applied on Kabylake too as shown by the corresponding
timeout errors about power well 1 and MISC IO power well disabling in
the latest CI run.
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460748778-4484-1-git-send-email-imre.deak@intel.com
When a vblank wait times out in intel_atomic_wait_for_vblanks() we just
get a cryptic 'WARN_ON(!ret)' backtrace in dmesg. Repace it with
something that tells you what actually happened.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460978973-24945-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
The legacy cursor ioctl expects to be asynchronous with respect to other
screen updates, in particular page flips. As X updates the cursor from a
signal context, if the cursor blocks then it will stall both the input
and output chains causing bad stuttering and horrible UX.
Reported-and-tested-by: Rafael Ristovski <rafael.ristovski@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94980
Fixes: 5008e874ed ("drm/i915: Make wait_for_flips interruptible.")
Suggested-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Link: http://patchwork.freedesktop.org/patch/msgid/1460922166-20292-1-git-send-email-chris@chris-wilson.co.uk
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Due to "some hardware limitation" the DPI enable bit in port C control
register does not get set on VLV. As a workaround we check the status in
pipe B conf register instead. The workaround was added in
commit c0beefd29f
Author: Gaurav K Singh <gaurav.k.singh@intel.com>
Date: Tue Dec 9 10:59:20 2014 +0530
drm/i915: Software workaround for getting the HW status of DSI Port C on BYT
Empirical evidence (on Surface 3 with DSI on port C per VBT) shows that
this is the case also on CHV, so extend the workaround to CHV. We still
have the device ready register check in place, so this should not get
confused with e.g. HDMI on pipe B.
This fixes a number of state checker warnings on CHV DSI port C.
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460724451-13810-1-git-send-email-jani.nikula@intel.com
Show a total and purgeable number of pin mapped objects
and their total and purgeable size.
Example output (new stat prefixed with a star):
# cat i915_gem_objects
19920 objects, 289243136 bytes
19920 [18466] objects, 288714752 [267911168] bytes in gtt
0 [0] active objects, 0 [0] bytes
19917 [18466] inactive objects, 288714752 [267911168] bytes
0 unbound objects, 0 bytes
0 purgeable objects, 0 bytes
1 pinned mappable objects, 3145728 bytes
0 fault mappable objects, 0 bytes
* 19914 [0] pin mapped objects, 285560832 [0] bytes [purgeable]
4294967296 [268435456] gtt total
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1460716493-27826-1-git-send-email-tvrtko.ursulin@linux.intel.com
Reflect the status of obj->mapping as added with the
i915_gem_object_pin_map API.
'M' was chosen to designate the pin mapped status.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
We don't have a LVDS_BORDER_ENABLE type of bit for either eDP or DSI,
and just trying to frob the display timings to include borders results
in a corrupted picture. So reject the 'Center' scaling mode on GMCH
platforms for eDP and DSI.
TODO: Should really filter out the unsupported modes from the prop,
but that would be fairly invasive since the prop is now created and
stored by drm core. So leave it for a rainy day.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460488478-18311-6-git-send-email-ville.syrjala@linux.intel.com
Tested-by: Jani Nikula <jani.nikula@intel.com>
Add the scaling mode property to DSI connectors, handle changes in the
property value, and compute the panel fitter state during
.compute_config().
v2: Handle BXT as well
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460488478-18311-5-git-send-email-ville.syrjala@linux.intel.com
Tested-by: Jani Nikula <jani.nikula@intel.com>
Compute the DSI PLL parameters during .compute_config() rather than
.pre_pll_enable() so that we can fail gracefully if we can't find
suitable parameters.
In order to do that we need to store the DSI PLL parameters in
pipe_config.
v2: Handle BXT too
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460488478-18311-3-git-send-email-ville.syrjala@linux.intel.com
Tested-by: Jani Nikula <jani.nikula@intel.com>
Set up DPLL and DPLL_MD even when driving DSI output on VLV/CHV. While
the DPLL isn't used to provide the clock we still need the refclock, and
it appears that the pixel repeat factor also has an effect on DSI
output. So set up eveyrhing in DPLL and DPLL_MD as we would do for
DP/HDMI/VGA, but don't actually enable the DPLL or configure the
dividers via DPIO.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460488478-18311-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Jani Nikula <jani.nikula@intel.com>
This patch is to correct one thing in this commit:
commit 25a5670533
Author: Dongwon Kim <dongwon.kim@intel.com>
Date: Wed Mar 16 18:06:13 2016 -0700
drm/i915/bxt: Reversed polarity of PORT_PLL_REF_SEL bit
This reversed bit polarity is actually common
for all BXT and APL SoCs. Therefore, revision checking
in the original commit should be removed to make
the bit set regardless of revision ID of GFX block.
Signed-off-by: Dongwon Kim <dongwon.kim@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460673463-14453-1-git-send-email-dongwon.kim@intel.com
I caught a few errors in our current PHY/CDCLK programming by sanity
checking the actual programmed state, so I thought it would be also
useful for the future. In addition to verifying the state after
programming it also verify it after exiting DC5, to make sure DMC
restored/kept intact everything related.
v2:
- Inlining __phy_reg_verify_state() doesn't make sense and also
incorrect, so don't do it (PW/CI gcc)
v3:
- Rebase on latest -nightly
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: David Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459780030-15781-1-git-send-email-imre.deak@intel.com
If BIOS has already programmed and enabled a PHY, don't reprogram it as
that may interfere with the currently active outputs. A follow-up patch
will add state verification, so we can catch any misconfiguration on
BIOS's behalf.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-14-git-send-email-imre.deak@intel.com
When determining whether CDCLK is enabled by BIOS and so we should skip
reprogramming it, we didn't check the related DBUF power request and
state. In theory BIOS could enable one without the other so check for
this case and reprogram things if something is amiss.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-13-git-send-email-imre.deak@intel.com
Power well 1 is managed by the DMC firmware so don't toggle it on-demand
from the driver. This means we need to follow the BSpec display
initialization sequence during driver loading and resuming (both system
and runtime) and enable power well 1 only once there. Afterwards DMC
will toggle power well 1 whenever entering/exiting DC5.
For this to work we also need to do away getting the PLL power domain,
since that just kept runtime PM disabled for good.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-12-git-send-email-imre.deak@intel.com
The power-down step logically belongs to the individual PHY uninit
sequence so move it there. The only functional change is that we will
power down now PHY 1 separately before PHY 0 and preserve the other bits
in the register which are defined as reserved.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-11-git-send-email-imre.deak@intel.com
For internal APIs passing dev_priv is preferred to reduce indirections,
so convert over a few DDI PHY, CDCLK helpers.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: David Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-10-git-send-email-imre.deak@intel.com
On Broxton we need to enable/disable power well 1 during the init/unit
display sequence similarly to Skylake/Kabylake. The code for this will
be added in a follow-up patch, but to prepare for that unexport
skl_pw1_misc_io_init(). It's a simple function called only from a single
place and having it inlined in the Skylake display core init/unit
functions will make it easier to compare it with its Broxton
counterpart.
This also flips the order of Misc IO and power well 1 disabling which
matches the enabling order. The specification doesn't prescribe the
disabling order, so this should be fine.
v2:
- Fix incorrect enable vs. disable power well call in
skl_display_core_uninit() (Patrik)
- Add commit comment about chaning the order of PW1 and Misc IO power
well disabling (Patrik)
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459773777-10701-1-git-send-email-imre.deak@intel.com
On SKL/KBL suspend-to-idle (aka freeze/s0ix) is performed with DMC
firmware assistance where the target display power state is DC6. On
Broxton on the other hand we don't use the firmware for this, but rely
instead on a manual DC9 flow. For this we have to uninitialize the
display following the BSpec display uninit sequence, just as during
S3/S4, so make sure we follow this sequence.
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-8-git-send-email-imre.deak@intel.com
The display power well support and DC state management doesn't depend on
runtime PM support, so remove the incorrect asserts about this.
Also Broxton does support DC5, so the related assert in
assert_can_enable_dc5() is incorrect. There is a more generic and
correct assert for this already in gen9_set_dc_state(), so we can remove
all the other ones.
At the same time convert WARNs to WARN_ONCE for consistency with the
other DC state asserts.
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-7-git-send-email-imre.deak@intel.com
So far we only power well enabling was synchronous not disabling. Since
we don't exactly know how the firmware (both DMC and PCU) synchronizes
against the actual power well state during DC transitions, make the
disabling also synchronous.
CC: Mika Kuoppala <mika.kuoppala@linux.intel.com>
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-6-git-send-email-imre.deak@intel.com
DMC forces on power well 1 and the misc IO power well by setting the
corresponding request bits both in the BIOS and the DEBUG power well
request registers. This is somewhat unexpected since the firmware should
really just save and restore state but not alter it. We also depend on
being able to disable power well 1, and the misc IO power well before
entering S3/S4 on BXT and SKL or entering DC9 on BXT. To fix this make
sure these request bits are cleared whenever we want to disable the
given power wells.
On SKL there is another twist where the firmware also clears the power
well 1 request bit in HSW_POWER_WELL_DRIVER (but not that of the misc IO
power well). This happens to not cause a problem due to the forced-on
request bits in the other request registers.
I've filed a bug about all this, but fixing that may take a while and
having this sanity check in place makes sense even for future firmware
versions.
At the same time also check the KVMR request bits. I haven't seen this
being altered, but we don't expect any request bits in here either, so
sanitize this register as well.
v2:
- Apply the workaround on SKL as well. I noticed the related failure
from the CI report, later Patrik also reported seeing it on his
machine.
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459851965-6137-1-git-send-email-imre.deak@intel.com
This register is read-only, so we have never actually set
OCL2_LDOFUSE_PWR_DIS in it as specified by the specification. Add a code
comment about this. I filed a specification update request to clarify
this there.
CC: Arthur J Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: David Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-4-git-send-email-imre.deak@intel.com
This has been corrected in BSpec quite some time ago, but we missed it
somehow. The wrong field definitions resulted in configuring PHY0 with
an incorrect GRC value.
v2:
- Remove the FIXME comment, we left in the code exactly about this
issue. (Ville)
CC: Arthur J Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-3-git-send-email-imre.deak@intel.com
DMC version 1.06 has a known bug, where the firmware polls forever for a
port PLL to lock, if the PLL was disabled when entering DC5, which locks
up the machine. Version 1.07 fixes this, so make that the minimum
required version on BXT.
CC: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-2-git-send-email-imre.deak@intel.com
Split the VLV/CHV hoplug irq handling to ack and handler phases. This
way we can move the actual irq handling outside the section where
we have disabled the interrupt sources.
For now, we leave things as is for pre-VLV GMCH platforms, but
eventually they could get the same treatment.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460571598-24452-9-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
On VLV/CHV the master interrupt enable bit only affects GT/PM
interrupts. Display interrupts are not affected by the master
irq control.
Also it seems that the CPU interrupt will only be generated when
the combined result of all GT/PM/display interrupts has a 0->1
edge. We already use the master interrupt enable bit to make sure
GT/PM interrupt can generate such an edge if we don't end up clearing
all IIR bits. We must do the same for display interrupts, and for
that we can simply clear out VLV_IER, and restore after we've acked
all the interrupts we are about to process.
So with both master interrupt enable and VLV_IER cleared out, we will
guarantee that there will be a 0->1 edge if any IIR bits are still set
at the end, and thus another CPU interrupt will be generated.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: 579de73b04 ("drm/i915: Exit cherryview_irq_handler() after one pass")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460571598-24452-6-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
On VLV/CHV VLV_IIR is not double double buffered, and it doesn't detect
edges from PIPESTAT & co. like it does on gen4. Instead it just
directly latches the level from PIPESTAT & co. That means we must clear
VLV_IIR after PIPESTAT & co. or else we'll get a spurious bit in VLV_IIR
every single time.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460571598-24452-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Use GEN8_MASTER_IRQ_CONTROL instead of DE_MASTER_IRQ_CONTROL or
MASTER_INTERRUPT_ENABLE with the GEN8_MASTER_IRQ register. They're
all bit 31 so there's no actual bug here, but let's be consistent
which name we use for the bit.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460571598-24452-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
On CHV GTFIFODBG has some read-only bits to indicate the number
of free FIFO entries. Ignore these when checking to see if any
of the sticky error bits are set.
This gets rid of these during device resume:
[drm:cherryview_enable_rps] GT fifo had a previous error 1080000
While at it, move the assignments out of the if().
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460570970-14073-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Allow for the MOCS to be programmed for all engines.
Currently we program the MOCS when the first render batch
goes through. This works on most platforms but fails on
platforms that do not run a render batch early,
i.e. headless servers. The patch now programs all initialised engines
on init and the RCS is programmed again within the initial batch. This
is done for predictable consistency with regards to the hardware
context.
Hardware context loading sets the values of the MOCS for RCS
and L3CC. Programming them from within the batch makes sure that
the render context is valid, no matter what the previous state of
the saved-context was.
v2: posted correct version to the mailing list.
v3: moved programming to within engine->init_hw() (Chris Wilson)
v4: code formatting and white-space changes. (Chris Wilson)
Testcase: igt/gem_mocs_settings
Signed-off-by: Peter Antoine <peter.antoine@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1460556205-6644-1-git-send-email-chris@chris-wilson.co.uk
Conceptually, each request is a record of a hardware transaction - we
build up a list of pending commands and then either commit them to
hardware, or cancel them. However, whilst building up the list of
pending commands, we may modify state outside of the request and make
references to the pending request. If we do so and then cancel that
request, external objects then point to the deleted request leading to
both graphical and memory corruption.
The easiest example is to consider object/VMA tracking. When we mark an
object as active in a request, we store a pointer to this, the most
recent request, in the object. Then we want to free that object, we wait
for the most recent request to be idle before proceeding (otherwise the
hardware will write to pages now owned by the system, or we will attempt
to read from those pages before the hardware is finished writing). If
the request was cancelled instead, that wait completes immediately. As a
result, all requests must be committed and not cancelled if the external
state is unknown.
All that remains of i915_gem_request_cancel() users are just a couple of
extremely unlikely allocation failures, so remove the API entirely.
A consequence of committing all incomplete requests is that we generate
excess breadcrumbs and fill the ring much more often with dummy work. We
have completely undone the outstanding_last_seqno optimisation.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93907
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-16-git-send-email-chris@chris-wilson.co.uk
Ville Syrjälä