The driver for Micrel PHYs is required for the Apalis iMX6 module
plugged into a Ixora carrier board featuring an on-module Micrel
KSZ9031 Gigabit PHY.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GPIO-based bitbanging I2C driver is required to make HDMI work on
the Apalis iMX6 module plugged into a Ixora carrier board featuring a
DDC channel to read a screen's EDID being hooked up to regular GPIOs.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6ul-14x14-evk has a wm8960 codec connected via SAI2 port.
Add support for it.
Thanks to Petr Kulhavy <brain@jikos.cz> for the hint on initializing
the PLL4 frequency to get a correct MCLK.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The following build warnings are seen when building with 'W=1' option:
Warning (unit_address_vs_reg): Node /soc/aips-bus@02000000/anatop@020c8000/regulator-1p1@110 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/aips-bus@02000000/anatop@020c8000/regulator-3p0@120 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/aips-bus@02000000/anatop@020c8000/regulator-2p5@130 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/aips-bus@02000000/anatop@020c8000/regulator-vddcore@140 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/aips-bus@02000000/anatop@020c8000/regulator-vddpu@140 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/aips-bus@02000000/anatop@020c8000/regulator-vddsoc@140 has a unit name, but no reg property
Fix them by removing the unneeded unit-addresses.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds the bus device tree nodes for INT (Internal) block
to enable the AMBA bus frequency scaling and add the NoC (Network on Chip)
Probe Device Tree node to measure the bandwidth for AMBA AXI bus.
The WCORE bus bus is parent device in INT block using VDD_INT.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch adds the AMBA bus nodes using VDD_INT for Exynos542x SoC.
Exynos542x has the following AMBA buses to translate data between
DRAM and sub-blocks.
Following list specifies the detailed correlation between sub-block and clock:
- CLK_DOUT_ACLK400_WCORE clock for WCORE's AXI
- CLK_DOUT_ACLK100_NOC for NoC (Network on Chip)'s AXI
- CLK_DOUT_PCLK200_FSYS for FSYS's APB
- CLK_DOUT_ACLK200_FSYS for FSYS's AXI
- CLK_DOUT_ACLK200_FSYS2 for FSYS2's AXI
- CLK_DOUT_ACLK333 for MFC's AXI
- CLK_DOUT_ACLK266 for GEN's AXI
- CLK_DOUT_ACLK66 for PERIC/PERIR's AXI
- CLK_DOUT_ACLK333_G2D for G2D's AXI
- CLK_DOUT_ACLK266_G2D for ACP's AXI
- CLK_DOUT_ACLK300_JPEG for JPEG's AXI
- CLK_DOUT_ACLK166 for JPEG's APB
- CLK_DOUT_ACLK300_DISP1 for FIMD's AXI
- CLK_DOUT_ACLK400_DISP1 for DISP1's AXI
- CLK_DOUT_ACLK300_GSCL for GSCL Scaler's AXI
- CLK_DOUT_ACLK400_MSCL for MSCL's AXI
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch adds the NoCP (Network on Chip Probe) Device Tree node
to measure the bandwidth of memory and g3d in Exynos542x SoC.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch adds the bus device tree nodes for both MIF (Memory) and INT
(Internal) block to enable the bus frequency.
The DMC bus is parent device in MIF block using VDD_MIF and the LEFTBUS
bus is parent device in INT block using VDD_INT.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[m.reichl and linux.amoon: Tested it on exynos4412-odroidu3 board]
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch expands the voltage range of buck1/3 regulator due to as following:
- MIF (Memory Interface) bus frequency needs the range of '900 - 1100 mV'.
- INT (Internal) bus frequency needs the range of '900 - 1050 mV'.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[m.reichl and linux.amoon: Tested it on exynos4412-odroidu3 board]
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch adds the bus device-tree nodes of INT (internal) block
to enable the bus frequency scaling. The following sub-blocks share
the VDD_INT power source:
- LEFTBUS (parent device)
- RIGHTBUS
- PERIL
- LCD0
- FSYS
- MCUISP / ISP
- MFC
The LEFTBUS is parent device with devfreq ondemand governor
and the rest of devices depend on the LEFTBUS device.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch adds the exynos4412-ppmu-common.dtsi to remove duplicate PPMU nodes
because exynos3250-rinato/monk, exynos4412-trats2/odroidu3 has the same
PPMU device tree node.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[m.reichl and linux.amoon: Tested it on exynos4412-odroidu3 board]
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch adds the bus nodes for Exynos4210 SoC. Exynos4210 SoC has
one power line for all buses to translate data between DRAM and sub-blocks.
Following list specifies the detailed relation between DRAM and sub-blocks:
- DMC/ACP clock for DMC (Dynamic Memory Controller)
- ACLK200 clock for LCD0
- ACLK100 clock for PERIL/PERIR/MFC(PCLK)
- ACLK160 clock for CAM/TV/LCD0/LCD1
- ACLK133 clock for FSYS/GPS
- GDL/GDR clock for LEFTBUS/RIGHTBUS
- SCLK_MFC clock for MFC
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch adds the bus nodes using VDD_INT for Exynos4x12 SoC.
Exynos4x12 has the following AXI buses to translate data between
DRAM and sub-blocks.
Following list specifies the detailed relation between DRAM and sub-blocks:
- ACLK100 clock for PERIL/PERIR/MFC(PCLK)
- ACLK160 clock for CAM/TV/LCD
: The minimum clock of ACLK160 should be over 160MHz.
When drop the clock under 160MHz, show the broken image.
- ACLK133 clock for FSYS
- GDL clock for LEFTBUS
- GDR clock for RIGHTBUS
- SCLK_MFC clock for MFC
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[m.reichl and linux.amoon: Tested it on exynos4412-odroidu3 board]
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch adds the bus nodes using VDD_MIF for Exynos4x12 SoC.
Exynos4x12 has the following AXI buses to translate data
between DRAM and DMC/ACP/C2C.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[m.reichl and linux.amoon: Tested it on exynos4412-odroidu3 board]
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch adds the bus nodes using VDD_INT for Exynos3250 SoC.
Exynos3250 has following AXI buses to translate data between
DRAM and sub-blocks.
Following list specifies the detailed relation between DRAM and sub-blocks:
- ACLK400 clock for MCUISP
- ACLK266 clock for ISP
- ACLK200 clock for FSYS
- ACLK160 clock for LCD0
- ACLK100 clock for PERIL
- GDL clock for LEFTBUS
- GDR clock for RIGHTBUS
- SCLK_MFC clock for MFC
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch adds the DMC (Dynamic Memory Controller) bus frequency node
which includes the devfreq-events and regulator properties. The bus
frequency support the DVFS (Dynamic Voltage Frequency Scaling) feature
with ondemand governor.
The devfreq-events (ppmu_dmc0*) can monitor the utilization of DMC bus
on runtime and the buck1_reg (VDD_MIF power line) supplies the power to
the DMC block.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch adds the DMC (Dynamic Memory Controller) bus node for Exynos3250 SoC.
The DMC is an AMBA AXI-compliant slave to interface external JEDEC standard
SDRAM devices. The bus includes the OPP tables and the source clock for DMC
block.
Following list specifies the detailed relation between the clock and DMC block:
- The source clock of DMC block : div_dmc
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Provide a helper to indicate whether we need to perform special handling
for boot identity mapping aliases or not.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Pratyush Anand <panand@redhat.com>
The real limit is the top of the visible physical address space with
the MMU turned off. Hence, we need to limit the crash kernel allocation
running-view physical address of the top of the boot-view physical
address space.
Reviewed-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For kexec, we need more functionality from the IDMAP system. We need to
be able to convert physical addresses to their identity mappped versions
as well as virtual addresses.
Convert the existing arch_virt_to_idmap() to deal with physical
addresses instead.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When the kernel crashkernel parameter is specified with just a size, we
are supposed to allocate a region from RAM to store the crashkernel.
However, ARM merely reserves physical address zero with no checking that
there is even RAM there.
Fix this by lifting similar code from x86, importing it to ARM with the
ARM specific parameters added. In the absence of any platform specific
information, we allocate the crashkernel region from the first 512MB of
physical memory.
Update the kdump documentation to reflect this change.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Pratyush Anand <panand@redhat.com>
imx6sx-sdb has custom operating points entries because it has one
power supply that drives both VDDARM_IN and VDDSOC_IN.
As per the MX6UL datasheet we have the following minimum voltages for
198 MHz operation (after adding the 25mV margin value):
VDDARM_IN = 0.975 V
VDDSOC_IN = 1.175 V
So use 1.175V for the 198MHz operation.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
mtdparts is passed from command line, so there is no need to have a
default partitioning in device-tree.
Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add initial support for imx6ul pico hobbit board.
For information about this board, please visit:
http://www.wandboard.org/images/hobbit/hobbitboard-imx6ul-reva1.pdf
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
I.MX6Quad Plus has a slightly different version of PCIe core than reqular
i.MX6Quad.
Tested-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
There several changes are done here:
- Convert the property to be in bytes
Besides that this is a common practice for such property, the use of a value
in bytes much more convenient than handling the encoded one.
- Rename data_width to data-width in the device tree bindings
The change leaves the support for the old format as well just in case someone
will use a newer kernel with an old device tree blob.
- While here, replace dwc_fast_ffs() by __ffs()
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The davinci_mmc driver no longer uses platform resources for getting dma
channels. Instead lookup is now done using dma_slave_map.
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This flag is a no-op now (see commit 47b0eeb3dc "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Pincontrol is not yet ready for all PXA platforms.
For example, a legacy platform, if PINCTRL was activated, will fail its
calls to gpio_request() or gpio_direction_output(), as the pinctrl
driver might not be available, such as for pxa25x and pxa3xx.
As a step forward, activate pincontrol for all device-tree available
machines, ie. pxa27x device-tree based and pxa3xx device-tree based.
If it appears later that pincontrol is also required for legacy
platforms and if the mfp->pinctrl conversion can be achieved, then
PINCTRL will be activated for the whole PXA architecture.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
A single regulator fix
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=C4f7
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.6' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Allwinner fixes for 4.6
A single regulator fix
* tag 'sunxi-fixes-for-4.6' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dts: sun8i-q8-common: Do not set constraints on dc1sw regulator
The davinci platform contains code that calls into the nvmem
subsystem, but that might be a loadable module, causing a
link error:
arch/arm/mach-davinci/built-in.o: In function `davinci_get_mac_addr':
:(.text+0x1088): undefined reference to `nvmem_device_read'
arch/arm/mach-davinci/built-in.o: In function `read_factory_config':
:(.text+0x214c): undefined reference to `nvmem_device_read'
Also, when NVMEM is completely disabled, the functions fail with
nonobvious error messages.
This ensures we only call the API functions when the code is actually
reachable from the board file, and otherwise prints a unique log
message.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: bec3c11bad ("misc: at24: replace memory_accessor with nvmem_device_read")
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the XUSB pad controller and XUSB controller (implementing an XHCI
interface) in the multi_v7 default configuration.
The XUSB pad controller is built-in because it is needed by PCIe, which
in turn provides the onboard ethernet used for network boot on a Jetson
TK1.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable the XUSB pad controller and XUSB controller (implementing an XHCI
interface) in the Tegra default configuration.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add XUSB pad controller and XUSB controller device tree nodes and enable
them with a configuration for the Nyan boards.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add XUSB pad controller and XUSB controller device tree nodes and enable
them with a configuration for the Jetson TK1 board.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add XUSB pad controller and XUSB controller device tree nodes and enable
them with a configuration for the Venice2 board.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a device tree node for the Tegra XUSB controller. It contains a
phandle to the XUSB pad controller for control of the PHYs assigned
to the USB ports.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The ARM architecture mandates that when changing a page table entry
from a valid entry to another valid entry, an invalid entry is first
written, TLB invalidated, and only then the new entry being written.
The current code doesn't respect this, directly writing the new
entry and only then invalidating TLBs. Let's fix it up.
Cc: <stable@vger.kernel.org>
Reported-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
- Fix few typos for address-cells and interrupt-names
- Update dra7 voltage rail limits
- Update compatible string for pcf8575 for both nxp and ti prefix
- Add omap5 configuration for gpadc
- Update dra7 for qspi to remove pinmux as it needs to be done by
the bootloader in isolation. Also update the qspi for 64MHz
frequency.
- Add support for Baltos ir2110 and ir3220
- Add industrial and commercial grade thermal thresholds for am57xx
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=LRKX
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.7/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "Part two of device tree changes for omaps for v4.7 merge window" from Tony Lindgren:
- Fix few typos for address-cells and interrupt-names
- Update dra7 voltage rail limits
- Update compatible string for pcf8575 for both nxp and ti prefix
- Add omap5 configuration for gpadc
- Update dra7 for qspi to remove pinmux as it needs to be done by
the bootloader in isolation. Also update the qspi for 64MHz
frequency.
- Add support for Baltos ir2110 and ir3220
- Add industrial and commercial grade thermal thresholds for am57xx
* tag 'omap-for-v4.7/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am57xx-idk: Include Industrial grade thermal thresholds
ARM: dts: am57xx-beagle-x15: Include the commercial grade thresholds
ARM: dts: am57xx: Introduce industrial grade thermal thresholds
ARM: dts: am57xx: Introduce commercial grade thermal thresholds
ARM: dts: add DTS for Baltos IR2110
ARM: dts: add DTS for Baltos IR3220
ARM: dts: split am335x-baltos-ir5221 into dts and dtsi files
ARM: dts: dra7x: Support QSPI MODE-0 operation at 64MHz
ARM: dts: dra7x: Remove QSPI pinmux
ARM: dts: omap5-board-common: describe gpadc for Palmas
ARM: dts: twl6030: describe gpadc
ARM: dts: dra7xx: Fix compatible string for PCF8575 chip
ARM: dts: AM57xx/DRA7: Update SoC voltage rail limits to match data sheet
ARM: dts: OMAP36xx: : DT spelling s/#address-cell/#address-cells/
ARM: dts: omap5-cm-t54: DT spelling s/interrupt-name/interrupt-names/
ARM: dts: omap5-board-common: DT spelling s/interrupt-name/interrupt-names/
Mostly enable drivers used on various boards as loadable modules
where possible. Also one warning fix related to RXKAD changes
heading to v4.7. And run make save_defconfig to shrink down the
size a bit.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lX8d
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.7/defconfig-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/defconfig
Merge "Defconfig changes for omap2plus_defconfig for v4.7 merge window" from Tony Lindgren:
Mostly enable drivers used on various boards as loadable modules
where possible. Also one warning fix related to RXKAD changes
heading to v4.7. And run make save_defconfig to shrink down the
size a bit.
* tag 'omap-for-v4.7/defconfig-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: omap2plus_defconfig: Enable PWM and ir-rx51 as loadable modules
ARM: omap2plus_defconfig: Enable twl6030 USB phy as loadable module
ARM: omap2plus_defconfig: Fix warning due invalid RXKAD symbol value
ARM: omap2plus_defconfig: Update with make savedefconfig
ARM: omap2plus_defconfig: Enable MDIO Bus/PHY emulation support
ARM: omap2plus_defconfig: Enable DP83867 support
ARM: omap2plus_defconfig: Enable GPIO_TPIC2810
- Remove now unnecessary multi vs single SoC compile time optimizations
as we are now using multiarch
- Configure dra7 powerdomains
- Clarify why omap-wakeupgen does not need to handle FROZEN transitions
- Add dra7 module configuration for MaASP, PWMSS and timer 12
- Add RTC module configuration unlock and lock functions
- Fix hwmod idle state sanity check sequence
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PZ/5
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.7/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Merge "SoC related changes for omaps for v4.7 merge window" from Tony Lindgren:
- Remove now unnecessary multi vs single SoC compile time optimizations
as we are now using multiarch
- Configure dra7 powerdomains
- Clarify why omap-wakeupgen does not need to handle FROZEN transitions
- Add dra7 module configuration for MaASP, PWMSS and timer 12
- Add RTC module configuration unlock and lock functions
- Fix hwmod idle state sanity check sequence
* tag 'omap-for-v4.7/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: wakeupgen: Add comment for unhandled FROZEN transitions
ARM: OMAP: DRA7: powerdomain data: Remove wrong OSWR capability
ARM: OMAP: DRA7: powerdomain data: Fix "ON" state for memories
ARM: OMAP: DRA7: powerdomain data: Erratum i892 workaround: Disable core INA
ARM: OMAP2+: remove redundant multiplatform checks
ARM: OMAP2+: hwmod: fix _idle() hwmod state sanity check sequence
ARM: DRA7: hwmod: Add data for GPTimer 12
ARM: AMx3xx: RTC: Add lock and unlock functions
ARM: DRA7: RTC: Add lock and unlock functions
ARM: OMAP2+: hwmod: RTC: Add lock and unlock functions
ARM: OMAP2+: DRA7: Add hwmod entries for PWMSS
ARM: DRA7: hwmod: Add data for McASP1/2/4/5/6/7/8
ARM: DRA7: clockdomain: Implement timer workaround for errata i874
ARM: OMAP2+: hwmod: Fix updating of sysconfig register
Let's pass the slot names in pdata like the legacy code does.
Once we have a generic DT binding for the slot names we can
switch to that.
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Before we start removing omap3 legacy booting support, let's make n900
DT booting behave the same way for ir-rx51 as the legacy booting does.
For now, we need to pass pdata to the ir-rx51 driver. This means that
the n900 tree can move to using DT based booting without having to carry
all the legacy platform data with it when it gets dropped from the mainline
tree.
Note that the ir-rx51 driver is currently disabled because of the
dependency to !ARCH_MULTIPLATFORM. This will get sorted out later
with the help of drivers/pwm/pwm-omap-dmtimer.c. But first we need
to add chained IRQ support to dmtimer code to avoid introducing new
custom frameworks.
So let's just pass the necessary dmtimer functions to ir-rx51 so we
can get it working in the following patch.
Cc: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This moves Samsung SROM controller code from arm/mach-exynos into to
separate driver under drivers/memory/samsung. In the future this driver
will be re-used on ARM64 Exynos platform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6ukR
-----END PGP SIGNATURE-----
Merge tag 'samsung-drivers-exynos-srom-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/drivers
Merge "Samsung soc/drivers update for v4.7" from Krzysztof Kozłowski:
This moves Samsung SROM controller code from arm/mach-exynos into to
separate driver under drivers/memory/samsung. In the future this driver
will be re-used on ARM64 Exynos platform.
* tag 'samsung-drivers-exynos-srom-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
memory: samsung: exynos-srom: Add support for bank configuration
ARM: EXYNOS: Remove SROM related register settings from mach-exynos
MAINTAINERS: Add maintainers entry for drivers/memory/samsung
memory: Add support for Exynos SROM driver
dt-bindings: EXYNOS: Add exynos-srom device tree binding
ARM: dts: change SROM node compatible from generic to model specific
* Add SYSC PM Domains to DT for R-Car Gen 1 and 2 SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=DcHM
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-pm-domain-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/late
Merge "Renesas ARM Based SoC DT PM Domain Updates for v4.7" into next/late
* Add SYSC PM Domains to DT for R-Car Gen 1 and 2 SoCs
This pull requests is based on a merge of:
* "[GIT PULL] Second Round of Renesas ARM Based SoC R-Car SYSC Updates for
v4.7", tagged as renesas-rcar-sysc2-for-v4.7, which you have already
pulled.
* "[GIT PULL v2] Renesas ARM Based SoC DT Updates for v4.7",
tagged as renesas-dt-for-v4.7, which you have also already pulled.
The reason for the somewhat tedious base on
renesas-rcar-sysc2-for-v4.7, which provides driver changes,
is a hard run-time dependency.
I also have a similar set of changes for arm64 which I will send separately.
* tag 'renesas-dt-pm-domain-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (88 commits)
ARM: dts: r8a7794: Use SYSC "always-on" PM Domain
ARM: dts: r8a7793: Use SYSC "always-on" PM Domain
ARM: dts: r8a7791: Use SYSC "always-on" PM Domain
ARM: dts: r8a7790: Use SYSC "always-on" PM Domain
ARM: dts: r8a7779: Use SYSC "always-on" PM Domain
ARM: dts: r8a7794: Add SYSC PM Domains
ARM: dts: r8a7793: Add SYSC PM Domains
ARM: dts: r8a7791: Add SYSC PM Domains
ARM: dts: r8a7790: Add SYSC PM Domains
ARM: dts: r8a7779: Add SYSC PM Domains
soc: renesas: rcar-sysc: Add support for R-Car H3 power areas
soc: renesas: rcar-sysc: Add support for R-Car E2 power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-N power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-W power areas
soc: renesas: rcar-sysc: Add support for R-Car H2 power areas
soc: renesas: rcar-sysc: Add support for R-Car H1 power areas
soc: renesas: rcar-sysc: Enable Clock Domain for I/O devices
ARM: dts: gose: Enable SDHI controllers
ARM: dts: r8a7793: Add SDHI controllers
ARM: dts: r8a7790: fix max-frequency for SDHI
...
This includes savedefconfig update of lpc32xx_defconfig, which removes
a number of outdated config options, plus ARM PrimeCell PL17x memory
controller driver is enabled by default now, on LPC32xx boards the
controller is commonly used to access SDRAM and NOR.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=yp6h
-----END PGP SIGNATURE-----
Merge tag 'lpc32xx-defconfig-4.7' of git://github.com/vzapolskiy/linux-lpc32xx into next/defconfig
Merge "NXP LPC32xx defconfig updates for v4.7" from Vladimir Zapolskiy:
This includes savedefconfig update of lpc32xx_defconfig, which removes
a number of outdated config options, plus ARM PrimeCell PL17x memory
controller driver is enabled by default now, on LPC32xx boards the
controller is commonly used to access SDRAM and NOR.
* tag 'lpc32xx-defconfig-4.7' of git://github.com/vzapolskiy/linux-lpc32xx:
ARM: LPC32xx: add PL175 memory controller driver to defconfig
ARM: LPC32xx: defconfig update
some time ago, before the driver was accepted (due to very late
comments). However, after these late comments, the driver expects
different bindings so we need to fix the DTS.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5P6R
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-exynos-srom-fixup-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Merge "ARM: dts: exynos: Fixup for SROM controller (v4.7)" from Krzysztof Kozlowski:
DeviceTree changes for new SROM controller driver reached mainline
some time ago, before the driver was accepted (due to very late
comments). However, after these late comments, the driver expects
different bindings so we need to fix the DTS.
* tag 'samsung-dt-exynos-srom-fixup-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: change SROM node compatible from generic to model specific
am57xx-idk have Industrial grade samples whose thermal
thresholds are different as compared with dra7. Hence correcting the same.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The silicon version ES2.0 onwards are industrial grade samples
and have higher thermal thresholds than commecial grade samples.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The silicon versions which are non ES2.0 are commercial grade silicon
and have lower thermal thresholds.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
1. Cleanup regulator bindings on Exynos5420 boards.
2. Support MIC bypass in display path for Exynos5420.
3. Enable PRNG and SSS for all Exynos4 devices.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ARFb
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Merge "Secound round of Samsung Device Tree updates and improvements for v4.7" from Krzysztof Kozlowski:
1. Cleanup regulator bindings on Exynos5420 boards.
2. Support MIC bypass in display path for Exynos5420.
3. Enable PRNG and SSS for all Exynos4 devices.
* tag 'samsung-dt-4.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Enable PRNG and SSS for all Exynos4 devices
ARM: dts: exynos: Add exynos5420-fimd compatible
ARM: dts: exynos: Remove unsupported s2mps11 regulator bindings from Exynos5420 boards
This includes a few functional changes:
* new representation of MIC, SIC1 and SIC2 interrupt controllers,
* disabled by default SPI1, SPI2, SSP0 and SSP1 SPI controllers in
shared lpc32xx.dtsi file,
* added clock sources for SPI1 and SPI2,
* set default clock rate of HCLK PLL to main osc rate multiplied by 16.
Also there are some non-functional changes:
* flatten board DTS files by exploiting device node labels,
* add 'partitions' device node for NAND SLC / MTD OF,
* correct Atmel vendor prefix to describe on board AT24 EEPROMs,
* rename board DTS files by adding SoC name prefix.
Since now DTS files of LPC32xx boards match "^lpc32[2345]0-" pattern.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=wDt+
-----END PGP SIGNATURE-----
Merge tag 'lpc32xx-dt-4.7' of git://github.com/vzapolskiy/linux-lpc32xx into next/dt
Merge "NXP LPC32xx device tree updates for v4.7" from Vladimir Zapolskiy:
This includes a few functional changes:
* new representation of MIC, SIC1 and SIC2 interrupt controllers,
* disabled by default SPI1, SPI2, SSP0 and SSP1 SPI controllers in
shared lpc32xx.dtsi file,
* added clock sources for SPI1 and SPI2,
* set default clock rate of HCLK PLL to main osc rate multiplied by 16.
Also there are some non-functional changes:
* flatten board DTS files by exploiting device node labels,
* add 'partitions' device node for NAND SLC / MTD OF,
* correct Atmel vendor prefix to describe on board AT24 EEPROMs,
* rename board DTS files by adding SoC name prefix.
Since now DTS files of LPC32xx boards match "^lpc32[2345]0-" pattern.
* tag 'lpc32xx-dt-4.7' of git://github.com/vzapolskiy/linux-lpc32xx:
ARM: dts: lpc32xx: phy3250: add SoC name prefix to board dts file
ARM: dts: lpc32xx: phy3250: add NAND partitions device node
ARM: dts: lpc32xx: phy3250: avoid extension of device nodes by absolute path
ARM: dts: lpc32xx: ea3250: add SoC name prefix to board dts file
ARM: dts: lpc32xx: ea3250: fix Atmel at24 eeprom vendor
ARM: dts: lpc32xx: ea3250: add NAND partitions device node
ARM: dts: lpc32xx: ea3250: avoid extension of device nodes by absolute path
ARM: dts: lpc32xx: reparent SIC1 and SIC2 interrupts from MIC
dt-bindings: interrupt-controllers: add description of SIC1 and SIC2
ARM: dts: lpc32xx: disabled ssp0/spi1 & ssp1/spi2 by default
ARM: dts: phy3250: enable ssp0
ARM: dts: lpc32xx: add clock properties to spi nodes
ARM: dts: lpc32xx: set default clock rate of HCLK PLL
- three low priority fixes:
- sama5d2: one pin definition and dependency with the slow clock for watchdog
- sama5d4: definition of watchdog IRQ property
- addition of the new shutdown controller to sama5d2 & sama5d2 Xplained
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJXINyNAAoJEAf03oE53VmQZtIH/1Ielv9yYUfQtFg8NHrjkLhM
nk0WWRjaWvwoPnmfGYF8SAv/tb9OM96uF4o+zv7rK8vWQVf2fi67R7MJ5bllGtaN
vgULv+jNixh/ocQb+SHZwRxhUQJbycIIfS5A8nDbUMUxpjIqC1iknpfytm2VyoPb
WWcuLoJ4LZ4HiZwRDeKvN/0pMDHbo7XzfgOCHC/QdW3lDEzGBEKSi+3cGIsaQOnS
LL11M/Ul4IBH6h2sct5w3SXlLu6vnc/DRYAP4SmwdQ+9gLfEkDCH9Vifbb7p9+tx
WbNIf+kZGkQHvTlI6tqUZwga4q+0KZwDyo7s0hRoZlH5BYIRXkrfh3bhVOW3tTo=
=Q/Ob
-----END PGP SIGNATURE-----
Merge tag 'at91-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/dt
Merge "Second batch of DT changes for 4.7" from Nicolas Ferre:
- three low priority fixes:
- sama5d2: one pin definition and dependency with the slow clock for watchdog
- sama5d4: definition of watchdog IRQ property
- addition of the new shutdown controller to sama5d2 & sama5d2 Xplained
* tag 'at91-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: dts: at91: sama5d2: add slow clock to watchdog node
ARM: dts: at91: sama5d2: add shutdown controller node
ARM: dts: at91: sama5d4: add watchdog interrupt property
ARM: dts: at91: fix typo in sama5d2 PIN_PD24 description
-----------
- Add CPUFreq support to STiH407 family
- Add Mailbox nodes to STiH407 family
- Add RemoteProc nodes to STiH407 family
- Use 'reserved-memory' for DMA memory on STiH407
- Use the LPC timer as a clocksource
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=S1d7
-----END PGP SIGNATURE-----
Merge tag 'sti-dt-for-v4.7b-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/sti into next/dt
Merge "STi DT updates for v4.7 #1" from Maxime Coquelin:
Highlights:
-----------
- Add CPUFreq support to STiH407 family
- Add Mailbox nodes to STiH407 family
- Add RemoteProc nodes to STiH407 family
- Use 'reserved-memory' for DMA memory on STiH407
- Use the LPC timer as a clocksource
* tag 'sti-dt-for-v4.7b-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/sti:
ARM: dts: STi: STih407: Switch LPC mode from RTC to Clocksource
ARM: dts: STiH407: Move over to using the 'reserved-memory' API for obtaining DMA memory
ARM: dts: STiH407: Add nodes for RemoteProc
ARM: dts: STi: stih407-family: Add nodes for Mailbox
ARM: dts: STi: STiH407: Provide CPU with a means to look-up Major number
ARM: dts: STi: STiH407: Link CPU with its voltage supply
ARM: dts: STi: STiH407: Provide CPU with clocking information
ARM: dts: STi: STiH407: Provide generic (safe) DVFS configuration
Move cpufreq bits for mvebu into drivers/cpufreq/ directory, that's
where they really belong to.
Compiled tested only.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
That will allow us to avoid using cpufreq-dt platform data.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The current kvm implementation on arm64 does cpu-specific initialization
at system boot, and has no way to gracefully shutdown a core in terms of
kvm. This prevents kexec from rebooting the system at EL2.
This patch adds a cpu tear-down function and also puts an existing cpu-init
code into a separate function, kvm_arch_hardware_disable() and
kvm_arch_hardware_enable() respectively.
We don't need the arm64 specific cpu hotplug hook any more.
Since this patch modifies common code between arm and arm64, one stub
definition, __cpu_reset_hyp_mode(), is added on arm side to avoid
compilation errors.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
[Rebase, added separate VHE init/exit path, changed resets use of
kvm_call_hyp() to the __version, en/disabled hardware in init_subsystems(),
added icache maintenance to __kvm_hyp_reset() and removed lr restore, removed
guest-enter after teardown handling]
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Define ARCH_EFI_IRQ_FLAGS_MASK for arm, which will enable the generic
runtime wrapper code to detect when firmware erroneously modifies flags
over a runtime services function call.
We check all allocated flags, barring those which firmware has
legitimate reason to modify (condition flags and IT state). While in
practice corruption of some flags (e.g. J) would already be fatal, we
include these for consistency and documentation purposes.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/1461614832-17633-39-git-send-email-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now there's a common template for {__,}efi_call_virt(), remove the
duplicate logic from the ARM EFI code.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/1461614832-17633-34-git-send-email-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Allows the efifb driver to be built for ARM and arm64. This simply involves
updating the Kconfig dependency expression, and supplying dummy versions of
efifb_setup_from_dmi().
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/1461614832-17633-25-git-send-email-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In order to hand over the framebuffer described by the GOP protocol and
discovered by the UEFI stub, make struct screen_info accessible by the
stub. This involves allocating a loader data buffer and passing it to the
kernel proper via a UEFI Configuration Table, since the UEFI stub executes
in the context of the decompressor, and cannot access the kernel's copy of
struct screen_info directly.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/1461614832-17633-22-git-send-email-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The Graphics Output Protocol code executes in the stub, so create a generic
version based on the x86 version in libstub so that we can move other archs
to it in subsequent patches. The new source file gop.c is added to the
libstub build for all architectures, but only wired up for x86.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/1461614832-17633-18-git-send-email-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Recent UEFI versions expose permission attributes for runtime services
memory regions, either in the UEFI memory map or in the separate memory
attributes table. This allows the kernel to map these regions with
stricter permissions, rather than the RWX permissions that are used by
default. So wire this up in our mapping routine.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/1461614832-17633-11-git-send-email-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
arm's mmu_context.h uses preempt_enable_no_resched and but doesn't
include anything that would pull in the declaration.
If I start including <asm/mmu_context.h> from <linux/mmu_context.h>
without this, the build breaks.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/5b95730a70f2dafe12d4fbf38d20eb7330d67ba3.1461688545.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The secondary CPU starts up in ARM mode. When the kernel is compiled in
thumb2 mode we have to explicitly compile the secondary startup
trampoline in ARM mode, otherwise the CPU will go to Nirvana.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reported-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Suggested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Remove redundant duplicate const, which is found by smatch:
arch/arm/mach-lpc32xx/phy3250.c:162:42: warning: duplicate const
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
After switching the platform to common clock framework there is no
more need to keep dead code in arch/arm/mach-lpc32xx, which glued
legacy clock source and clock provider drivers, remove the leftovers.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The header file "reboot.h" is no longer needed, following
the migration of the restart code into the pnx4008 watchdog.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
To simplify matching of DTS files of all NXP LPC32xx powered boards by
a file name add 'lpc3250' prefix to PHYTEC PHYCORE-LPC3250 board dts
file.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
To declare MTD OF partitions NAND controller device node should have
a special 'partitions' subnode, the change removes a debug message
from mtd/ofpart on boot:
nxp_lpc3220_slc: 'partitions' subnode not found on /ahb/flash@20020000.
Trying to parse direct subnodes as partitions.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The change simplifies layout of PHY3250 board description by
referencing device nodes of LPC32xx controllers by label.
No functional change intended.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
To simplify matching of DTS files of all NXP LPC32xx powered boards by
a file name add 'lpc3250' prefix to Embedded Artists LPC3250 board dts
file.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
There is no 'at' hardware vendor defined yet, correct vendor prefix
for Atmel is 'atmel'.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
To declare MTD OF partitions NAND controller device node should have
a special 'partitions' subnode, the change removes a debug message
from mtd/ofpart on boot:
nxp_lpc3220_slc: 'partitions' subnode not found on /ahb/flash@20020000.
Trying to parse direct subnodes as partitions.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The change simplifies layout of EA3250 board description by
referencing device nodes of LPC32xx controllers by label.
No functional change intended.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The change adds separate device nodes for SIC1 and SIC2 interrupt
controllers and reparents all defined SIC1 and SIC2 interrupt
producers to the correspondent interrupt controller, this is needed to
perform switching to a new LPC32xx MIC/SIC interrupt controller driver.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The default remains 127, which is good for most cases, and not even hit
most of the time, but then for some cases, as reported by Brendan, 1024+
deep frames are appearing on the radar for things like groovy, ruby.
And in some workloads putting a _lower_ cap on this may make sense. One
that is per event still needs to be put in place tho.
The new file is:
# cat /proc/sys/kernel/perf_event_max_stack
127
Chaging it:
# echo 256 > /proc/sys/kernel/perf_event_max_stack
# cat /proc/sys/kernel/perf_event_max_stack
256
But as soon as there is some event using callchains we get:
# echo 512 > /proc/sys/kernel/perf_event_max_stack
-bash: echo: write error: Device or resource busy
#
Because we only allocate the callchain percpu data structures when there
is a user, which allows for changing the max easily, its just a matter
of having no callchain users at that point.
Reported-and-Tested-by: Brendan Gregg <brendan.d.gregg@gmail.com>
Reviewed-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: David Ahern <dsahern@gmail.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Milian Wolff <milian.wolff@kdab.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: Wang Nan <wangnan0@huawei.com>
Cc: Zefan Li <lizefan@huawei.com>
Link: http://lkml.kernel.org/r/20160426002928.GB16708@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Fix gpio active flag for the phy reset-gpios property. The line is
active low instead of active high.
Actually, this flags was never used by the macb driver.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
As the watchdog timer needs the slow clock, add it to the currently defined
wdt node.
Reported-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add the SAMA5D2-Compatible Shutdown Controller node to sama5d2.dtsi
and the use of it in the sama5d2 Xplained board dts file.
Enable the RTC wakeup event and the "wake up" button support through the
input "0" that is present on the board.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The "interrupts" property is missing from the watchdog node. Add it with
highest priority value of 7.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add the Atmel Pulse Density Modulation Interface Controller (PDMIC) driver
as a module. It's used by sama5d2 SoC for instance.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add both Atmel watchdog timers to the multi_v7_defconfig. They are added
as part of the kernel because it's a core piece of the system.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add the HLCDC drivers to multi_v7_defconfig.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add Pulse Density Modulation Interface Controller (PDMIC) driver compilation
for sama5 default configuration. Is used by sama5d2 SoC for instance.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add the LCD DRM driver with all its dependencies:
- the MFD driver
- the backlight PWM
- the simple panel driver
Remove the CONFIG_FB as it is not needed on any sama5 device.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Selection of the HDMAC option is now needed to allow some sama5 devices
to have the DMA driver compiled and available.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This flag is a no-op now (see commit 47b0eeb3dc "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This flag is a no-op now (see commit 47b0eeb3dc "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This flag is a no-op now (see commit 47b0eeb3dc "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The da850 family of processors has an async3 clock domain that can be
muxed to either pll0_sysclk2 or pll1_sysclk2. Now that the davinci clocks
have a set_parent callback, we can use this to control the async3 mux
instead of a stand-alone function.
This adds a new async3_clk and sets the appropriate child clocks. The
default is use to pll1_sysclk2 since it is not affected by processor
frequency scaling.
Signed-off-by: David Lechner <david@lechnology.com>
[nsekhar@ti.com: drop unnecessary comment]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Some clocks (such as the USB PHY clocks in DA8xx) will need to use iomem.
The davinci_common_init() function must be called before the ioremap, so
the clock init is now split out as separate function.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
power domain, if there was no turn off before. Usually all power domains
are on, so the first action is to turn off but some older bootloaders
might behave differently.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Ubwx
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into fixes
Fix for more theoretical than practical OOPS on first turn on of a exynos
power domain, if there was no turn off before. Usually all power domains
are on, so the first action is to turn off but some older bootloaders
might behave differently.
* tag 'samsung-fixes-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: EXYNOS: Properly skip unitialized parent clock in power domain on
There is no external dependency for Security SubSystem (SSS) block so
the nodes for Pseudo Random Number Generator and AES hardware
acceleration can be enabled always for all Exynos4 devices.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch changes the compatible of Exynos5420 fimd
to "exynos5420-fimd". To support MIC bypass from display
path, the new compatible is introduced for Exynos5420.
Cc: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
The bindings like s2mps11,buck6-ramp-enable or s2mps11,buck2-ramp-delay
were ignored. They were never parsed by s2mps11 regulator driver. Also
the values used in these bindings were equal to default reset values of
S2MPS11 device. It is safe to remove them.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Hook up all devices that are part of the CPG/MSTP Clock Domain to the
SYSC "always-on" PM Domain, for a more consistent device-power-area
description in DT.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Hook up all devices that are part of the CPG/MSTP Clock Domain to the
SYSC "always-on" PM Domain, for a more consistent device-power-area
description in DT.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Hook up all devices that are part of the CPG/MSTP Clock Domain to the
SYSC "always-on" PM Domain, for a more consistent device-power-area
description in DT.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Hook up all devices that are part of the CPG/MSTP Clock Domain to the
SYSC "always-on" PM Domain, for a more consistent device-power-area
description in DT.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Hook up all devices that are part of the CPG/MSTP Clock Domain to the
SYSC "always-on" PM Domain, for a more consistent device-power-area
description in DT.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the System Controller.
Hook up the Cortex-A7 CPU cores and the Cortex-A7 L2 cache/SCU to their
respective PM Domains.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the System Controller.
Hook up the first Cortex-A15 CPU core and the Cortex-A15 L2 cache/SCU to
their respective PM Domains.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the System Controller.
Hook up the Cortex-A15 CPU cores and the Cortex-A15 L2 cache/SCU to
their respective PM Domains.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the System Controller.
Hook up the Cortex-A15 and Cortex-A7 CPU cores and L2 caches/SCUs to
their respective PM Domains.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the System Controller.
Hook up ARM CPU cores 1-3 to their respective PM Domains.
Note that ARM CPU core 0 cannot be shut off.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Using "IMX6QDL_CLK_CKO" for the clock is easier to read instead of
the hardcoded clock number.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Embest MarS Board [1] is a multi-core platform based on Freescale i.MX6
Cortex-A9 Dual Core, running up to 1GHz with 1 GB of RAM, 4GB of eMMC
and with a 4MB SPI flash.
[1] http://www.embest-tech.com/shop/star/marsboard.html
Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
clk_get() on a disabled clock node will return -EPROBE_DEFER, which can
cause drivers to be deferred forever if such clocks are referenced in
their devices' clocks properties.
Update the various disabled external clock nodes to default to a
frequency of 0, but don't disable them, to prevent this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
clk_get() on a disabled clock node will return -EPROBE_DEFER, which can
cause drivers to be deferred forever if such clocks are referenced in
their devices' clocks properties.
Update the various disabled external clock nodes to default to a
frequency of 0, but don't disable them, to prevent this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
clk_get() on a disabled clock node will return -EPROBE_DEFER, which can
cause drivers to be deferred forever if such clocks are referenced in
their devices' clocks properties.
Update the various disabled external clock nodes to default to a
frequency of 0, but don't disable them, to prevent this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
clk_get() on a disabled clock node will return -EPROBE_DEFER, which can
cause drivers to be deferred forever if such clocks are referenced in
their devices' clocks properties.
Update the various disabled external clock nodes to default to a
frequency of 0, but don't disable them, to prevent this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
clk_get() on a disabled clock node will return -EPROBE_DEFER, which can
cause drivers to be deferred forever if such clocks are referenced in
their devices' clocks properties.
Update the various disabled external clock nodes to default to a
frequency of 0, but don't disable them, to prevent this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Introduce a DT-based driver for the R-Car System Controller, as found on
Renesas R-Car H1, R-Car Gen2, and R-Car Gen3 SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXHryuAAoJENfPZGlqN0++Zq4QAJkrqIK774IUSa58+U4bMG2h
ceRhG+uqr5AGoQJ/pEpFZjgaLe7hmrgKQmF2Uh1uWns633o2t6N2rR6gM36/BTqh
HyyCMKT4vUoU6lyZ7qnB8LOxRj4oRa5J2C82rROWRx9m7TNmyHpA05KZUW2sUMmi
6/g+YF0wT8XbwSjUskxFSwO8TeKNcOSpFi0wWVR1WUh2RhVNbGXhyUSxxGTD3Ojt
X6f1YmrfJmwzI0cY8AZScOr7WCU0HFk8IZRkEbg8t39TVOrEL5o97Ki9QK6WaGf8
uKA7gA1eDhO8DSXX1ycawx8uh4AxRGgYSZFc0Lq7E08k+VTn7D7qDsk4DDz+JnpH
aLy95N4lDuQf9iiKFWEECc2OK3hxAnJb8c4yU2pS7tg1K4JNMT0iUkp2Ha+/RLrd
+FcWYcerXLziBItseM0caDPyv7PXpNLpLnqfgYPAOcP4h5+tT8burH9Ic5zHdFgZ
JAD30KBYH8xB7wRisf4S/MP6sHFD8XQl6WdQK1Vwl1oPitRRdgDIxaFhyDszli3O
/mX5+iMavM/s36MZwAgck2nTNTal1CHqupzkvWzttee3sZXzmK8QuiYLqI8iqz2i
HPxXM90IjzfQNtBZH6ZVdL3xCh8HKkzQdD6wb7I2nP7clMHJlNmQwanXcSw6vcvB
/Jx3o0v31gXfdUx3lgCy
=Lg0X
-----END PGP SIGNATURE-----
Merge tag 'renesas-rcar-sysc2-for-v4.7' into dt-pm-domain-for-v4.7
Second Round of Renesas ARM Based SoC R-Car SYSC Updates for v4.7
Introduce a DT-based driver for the R-Car System Controller, as found on
Renesas R-Car H1, R-Car Gen2, and R-Car Gen3 SoCs.
recent regressions. Changes are across several platforms, so
I'm listing every change separately here.
Regressions since 4.5:
- A correction of the psci firmware DT binding, to prevent
users from relying on unintended semantics
- Actually getting the newly merged clock driver for some OMAP
platforms to work
- A revert of patches for the Qualcomm BAM, these need to be
reworked for 4.7 to avoid breaking boards other than the one
they were intended for
- A correction for the I2C device nodes on the Socionext Uniphier
platform
- i.MX SDHCI was broken for non-DT platforms due to a change
with the setting of the DMA mask
- A revert of a patch that accidentally added a nonexisting
clock on the Rensas "Porter" board
- A couple of OMAP fixes that are all related to suspend after
the power domain changes for dra7
- On Mediatek, revert part of the power domain initialization
changes that broke mt8173-evb
Fixes for older bugs:
- Workaround for an "external abort" in the omap34xx
suspend/resume code.
- The USB1/eSATA should not be listed as an excon device on
am57xx-beagle-x15 (broken since v4.0)
- A v4.5 regression in the TI AM33xx and AM43XX DT specifying
incorrect DMA request lines for the GPMC
- The jiffies calibration on Renesas platforms was incorrect
for some modern CPU cores.
- A hardware errata woraround for clockdomains on TI DRA7
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YgL2
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Here are the latest bug fixes for ARM SoCs, mostly addressing recent
regressions. Changes are across several platforms, so I'm listing
every change separately here.
Regressions since 4.5:
- A correction of the psci firmware DT binding, to prevent users from
relying on unintended semantics
- Actually getting the newly merged clock driver for some OMAP
platforms to work
- A revert of patches for the Qualcomm BAM, these need to be reworked
for 4.7 to avoid breaking boards other than the one they were
intended for
- A correction for the I2C device nodes on the Socionext Uniphier
platform
- i.MX SDHCI was broken for non-DT platforms due to a change with the
setting of the DMA mask
- A revert of a patch that accidentally added a nonexisting clock on
the Rensas "Porter" board
- A couple of OMAP fixes that are all related to suspend after the
power domain changes for dra7
- On Mediatek, revert part of the power domain initialization changes
that broke mt8173-evb
Fixes for older bugs:
- Workaround for an "external abort" in the omap34xx suspend/resume
code.
- The USB1/eSATA should not be listed as an excon device on
am57xx-beagle-x15 (broken since v4.0)
- A v4.5 regression in the TI AM33xx and AM43XX DT specifying
incorrect DMA request lines for the GPMC
- The jiffies calibration on Renesas platforms was incorrect for some
modern CPU cores.
- A hardware errata woraround for clockdomains on TI DRA7"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
drivers: firmware: psci: unify enable-method binding on ARM {64,32}-bit systems
arm64: dts: uniphier: fix I2C nodes of PH1-LD20
ARM: shmobile: timer: Fix preset_lpj leading to too short delays
Revert "ARM: dts: porter: Enable SCIF_CLK frequency and pins"
ARM: dts: r8a7791: Don't disable referenced optional clocks
Revert "ARM: OMAP: Catch callers of revision information prior to it being populated"
ARM: OMAP3: Fix external abort on 36xx waking from off mode idle
ARM: dts: am57xx-beagle-x15: remove extcon_usb1
ARM: dts: am437x: Fix GPMC dma properties
ARM: dts: am33xx: Fix GPMC dma properties
Revert "soc: mediatek: SCPSYS: Fix double enabling of regulators"
ARM: mach-imx: sdhci-esdhc-imx: initialize DMA mask
ARM: DRA7: clockdomain: Implement timer workaround for errata i874
ARM: OMAP: Catch callers of revision information prior to it being populated
ARM: dts: dra7: Correct clock tree for sys_32k_ck
ARM: OMAP: DRA7: Provide proper class to omap2_set_globals_tap
ARM: OMAP: DRA7: wakeupgen: Skip SAR save for wakeupgen
Revert "dts: msm8974: Add dma channels for blsp2_i2c1 node"
Revert "dts: msm8974: Add blsp2_bam dma node"
ARM: dts: Add clocks for dm814x ADPLL
Introduce am335x-baltos.dtsi, that provides common configuration
for the whole device family based on the same SODIMM module.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to Data Manual(SPRS915P) of AM57x, TI QSPI controller on
DRA74(rev 1.1+)/DRA72 EVM can support up to 64MHz in MODE-0, whereas
MODE-3 is limited to 48MHz. Hence, switch to MODE-0 for better
throughput.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DRA7 family of processors from Texas Instruments, have a hardware module
called IODELAYCONFIG Module which is expected to be configured. This
block allows very specific custom fine tuning for electrical
characteristics of IO pins that are necessary for functionality and
device lifetime requirements. IODelay module has it's own register space
with registers to configure various pins.
According to AM572x TRM SPRUHZ6E October 2014–Revised January 2016[1]
section 18.4.6.1 Pad Configuration, in addition to pinmuxing(MUXMODE),
when operating a pad in certain mode, Virtual/Manual IO Timing Mode must
also be configured to ensure that IO timings are met (DELAYMODE and
MODESELECT fields of pad's IODELAYCONFIG module register). According to
section 18.4.6.1.7 Isolation Requirements of above TRM, when
reprogramming MUXMODE, DELAYMODE, and MODESELECT fields, there is a
potential for a significant glitch on the corresponding IO. It is hence
recommended to do this with I/O isolation (which can only be done in
initial stages of bootloader). QSPI is one such module that requires
IODELAY configuration. So, this patch removes the pinmux for
QSPI for DRA74/DRA72 EVM as it needs to be done in bootloader (U-Boot)
and cannot be done in kernel.
Users should migrate to U-Boot v2016.05-rc1 or higher.
[1] http://www.ti.com/lit/ug/spruhz6e/spruhz6e.pdf
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 648af7fca1 ("rxrpc: Absorb the rxkad security module") changed
the RXKAD Kconfig symbol from tristate to boolean but the commit didn't
update the omap2plus_defconfig that was enabling CONFIG_RXKAD as module.
This leads to the following warning when using the omap2plus_defconfig:
arch/arm/configs/omap2plus_defconfig:112:warning: symbol value 'm' invalid for RXKAD
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Without that, regulators are left in the mode last set by the bootloader or
by the kernel the device was rebooted from. This leads to various problems,
like non-working peripherals.
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the TRM, SCM CONTROL_CSIRXFE register is on offset 0x6c
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The boards use a TI variant of the PCF8575 so specify that
in the compatible string.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As per the data sheet starting from SPRUHQ0H (Nov 2015 - Latest[1]),
VDD_CORE can vary from 0.85v to 1.15v for AVS class0. VDD GPU/DSP
et.al. can range from 0.85v to 1.25V with AVS class0
Since dynamic voltage scaling is disabled for DRA7/AM57xx SoCs for
all SoC rails other than MPU, the bootloader is responsible for
setting up the AVS class0 voltage, however, with wrong voltage machine
constraints in dtb, regulator framework will lower the voltage below
the required voltage levels for certain samples in production flow.
This can cause catastrophic failures which can be pretty hard to
identify.
Update board files which don't match required specification.
[1] http://www.ti.com/product/AM5728/datasheet/specifications#SPRT637-7340
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ldo4_reg is connected to DSS, and should always be 1.8V. However the The
dts defines a range of 1.5V-1.8V, which requires somethings to set the
actual voltage at runtime. Currently we set the voltage in omapdss
driver.
As the voltage must always be 1.8V, let's just define the range to 1.8V
so that the driver doesn't need to deal with the voltage. In fact, the
driver should not touch the voltage, except in the cases where the
voltage needs to be changed at runtime.
I presume the situation is the same for ldo1_reg, used for CSI, although
I think it is not currently used in the mainline.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ldo4_reg is connected to DSS, and should always be 1.8V. However the
The dts defines a range of 1.5V-1.8V, which requires somethings to set
the actual voltage at runtime. Currently we set the voltage in omapdss
driver.
As the voltage must always be 1.8V, let's just define the range to 1.8V
so that the driver doesn't need to deal with the voltage. In fact, the
driver should not touch the voltage, except in the cases where the
voltage needs to be changed at runtime.
I presume the situation is the same for ldo1_reg, used for CSI, although
I think it is not currently used in the mainline.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Doing so saves quite a bit of code in the driver.
For more information on the 'reserved-memory' bindings see:
Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt
Suggested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This patch supplies the Mailbox Controller nodes. In order to
request channels, these nodes will be referenced by Mailbox
Client nodes.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
You'll notice that the voltage cell is populated with 0's. Voltage
information is very platform specific, even depends on 'cut' and
'substrate' versions. Thus it is left blank for a generic (safe)
implementation. If other nodes/properties are provided by the
bootloader, the ST CPUFreq driver will over-ride these generic
values.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
When compiled with "W=1", dtc complains: e.g.
"Warning (unit_address_vs_reg):
Node /soc/ipu@02800000/port@2/endpoint@0
has a unit name, but no reg property"
Endpoint nodes don't have a reg property, and the addresses
in their node names are ordinals without any special meaning
so remove them and swap them for semantic node names.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Table 8 from MX6DL datasheet (IMX6SDLCEC Rev. 5, 06/2015):
http://cache.nxp.com/files/32bit/doc/data_sheet/IMX6SDLCEC.pdf
states the following:
"LDO Output Set Point (VDD_ARM_CAP) = 1.125 V minimum for operation
up to 396 MHz."
So fix the entry by adding the 25mV margin value as done in the other
entries of the table, which results in 1.15V for 396MHz operation.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
198MHz is a valid operating point for mx6sx.
Add entries for VDD_ARM_CAP and VDD_SOC_CAP voltages for 198MHz according
to the imx6sx datahseet:
http://cache.nxp.com/files/32bit/doc/data_sheet/IMX6SXIEC.pdf
(a 25mV offset is added to the minimum allowed values for safety).
These values also match the ones from the NXP kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adjust the VDD_ARM_CAP and VDD_SOC_CAP voltages according to
Table-11 from MX6UL datasheet:
http://cache.nxp.com/files/32bit/doc/data_sheet/IMX6ULCEC.pdf
(a 25mV offset is added to the minimum allowed values for safety).
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XtF2
-----END PGP SIGNATURE-----
Merge tag 'ox810se-arm-v4.6-rc3' of https://github.com/superna9999/linux into next/soc
Merge "ARM: Add OXNAS Platform Support" from Neil Armstrong
This is for the ARM926 based ox810 chip used in some older
NAS appliances. There is another related ox820 chip based on
ARM11 that might get added here later.
* tag 'ox810se-arm-v4.6-rc3' of https://github.com/superna9999/linux:
MAINTAINERS: add maintainer entry for ARM/OXNAS platform
ARM: Add new mach-oxnas
irqchip: versatile-fpga: add new compatible for OX810SE SoC
* Remove Gen2 designation from Kconfig for R-Car PCIE driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HTRw
-----END PGP SIGNATURE-----
Merge tag 'renesas-pci-defconfig-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/defconfig
Merge "Renesas ARM Based SoC Pci Defconfig Updates for v4.7" from Simon Horman:
* Remove Gen2 designation from Kconfig for R-Car PCIE driver
* tag 'renesas-pci-defconfig-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
PCI: rcar-pcie: Remove Gen2 designation from Kconfig
DEBUG_HI3716_UART was supposed to be renamed to DEBUG_HIX5HD2_UART, but
accidentally both got left in place, which results in a build error when
CONFIG_DEBUG_UART_PHYS is not set as it should be.
This removes the old symbol.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 12aae30974 ("ARM: debug: Rename Hi3716 to HIX5HD2")
Acked-by: Wei Xu <xuwei5@hisilicon.com>
This patch adds a new config for MPS2 platform.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Application Notes 399 and 400 shares the same memory map and
features. Both are shipped with Cortex-M7 and have the same peripheral
as AN385/AN386, but with different location of PSRAM and Ethernet
controller.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Application Notes 385 and 386 shares the same memory map and features
except the CPU is used. AN385 is supplied with Cortex-M3 CPU and AN386
is supplied with Cortex-M4.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The Cortex-M Prototyping System (or V2M-MPS2) is designed for
prototyping and evaluation Cortex-M family of processors including the
latest Cortex-M7
It comes with a range of useful peripherals including 8MB single cycle
SRAM, 16MB PSRAM, Ethernet, QSVGA touch screen panel, 4bit RGB VGA
connector, Audio, SPI and GPIO.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
* Correct preset_lpj calculation which may lead to too short delays
* Correct handling of optional clocks on r8a7791 to restore
access to the serial port the porter board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=k7qU
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Renesas ARM Based SoC Fixes for v4.6
* Correct preset_lpj calculation which may lead to too short delays
* Correct handling of optional clocks on r8a7791 to restore
access to the serial port the porter board
This is a backmerge of v4.6 fixes, to avoid a merge conflict between 4.6
and our next/dt branch.
* tag 'renesas-fixes-for-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: timer: Fix preset_lpj leading to too short delays
Revert "ARM: dts: porter: Enable SCIF_CLK frequency and pins"
ARM: dts: r8a7791: Don't disable referenced optional clocks
Fix a typo on PIN_PD24 for UTXD2 and FLEXCOM4_IO3 which were
wrongly linked to PIN_PD23).
Signed-off-by: Florian Vallee <fvallee@eukrea.fr>
Fixes: 7f16cb676c ("ARM: at91/dt: add sama5d2 pinmux")
Cc: stable@vger.kernel.org # v4.4+
[nicolas.ferre@atmel.com: add commit message, changed subject]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Introduce a DT-based driver for the R-Car System Controller, as found on
Renesas R-Car H1, R-Car Gen2, and R-Car Gen3 SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Lg0X
-----END PGP SIGNATURE-----
Merge tag 'renesas-rcar-sysc2-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/drivers
Merge "Second Round of Renesas ARM Based SoC R-Car SYSC Updates for v4.7" from Simon Horman:
Introduce a DT-based driver for the R-Car System Controller, as found on
Renesas R-Car H1, R-Car Gen2, and R-Car Gen3 SoCs.
* tag 'renesas-rcar-sysc2-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (30 commits)
soc: renesas: rcar-sysc: Add support for R-Car H3 power areas
soc: renesas: rcar-sysc: Add support for R-Car E2 power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-N power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-W power areas
soc: renesas: rcar-sysc: Add support for R-Car H2 power areas
soc: renesas: rcar-sysc: Add support for R-Car H1 power areas
soc: renesas: rcar-sysc: Enable Clock Domain for I/O devices
soc: renesas: rcar-sysc: Make rcar_sysc_power_is_off() static
soc: renesas: rcar-sysc: Add DT support for SYSC PM domains
soc: renesas: rcar-sysc: Improve rcar_sysc_power() debug info
soc: renesas: Move pm-rcar to drivers/soc/renesas/rcar-sysc
clk: renesas: cpg-mssr: Export cpg_mssr_{at,de}tach_dev()
clk: renesas: mstp: Provide dummy attach/detach_dev callbacks
clk: renesas: Provide Kconfig symbols for CPG/MSSR and CPG/MSTP support
soc: renesas: Add r8a7795 SYSC PM Domain Binding Definitions
soc: renesas: Add r8a7794 SYSC PM Domain Binding Definitions
soc: renesas: Add r8a7793 SYSC PM Domain Binding Definitions
soc: renesas: Add r8a7791 SYSC PM Domain Binding Definitions
soc: renesas: Add r8a7790 SYSC PM Domain Binding Definitions
soc: renesas: Add r8a7779 SYSC PM Domain Binding Definitions
...
Add Western Digital My Book World Edition device tree based on
Oxford Semiconductor OX810SE SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The BA16 module has a PMIC that uses the WDOG_B output from iMX6 to
reset the system on a watchdog timeout. Configure the watchdog to assert
the external reset signal (WDOG_B) using fsl,ext-reset-output property.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Previously the LDB_DIx clocks could be specified in the ldb node. With
the ERR009219 errata fix applied, the ldb_di clocks now needs to be
specified in the clks node to ensure the clocks are setup early in the
boot process.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The default monitor that ships with B850v3 requires a 65MHz pixel clock.
65MHz can not be achieved using PLL3 (480MHz/7=68.5MHz). Hence set the
LDB_DIx clock source to PLL5. Since PLL5 is already in use by IPU1_DIx,
set the clock source for IPU1_DIx to PLL2_PFD2 to allow simultaneous
display on both LVDS and HDMI interface.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove ldb panel entry for the following reasons:
- The b850v3 has an onboard LVDS to DisplayPort converter (STDP4028). So
we should not limit the monitors that can be connected by hardcoding the
auo,b133htn01 1080p panel.
- The default resolution on the LVDS interface needs to be WXGA or less.
Otherwise when a 1080p monitor is connected to the HDMI port there is no
output on both the LVDS and HDMI ports since a single IPU on i.MX6 can
not handle two 1080p displays. With the panel entry removed from the
devicetree, drm driver defaults the resolution on LVDS interface to XGA.
Once in userspace, applications can set the desired resolution on LVDS
interface over IPU2 CRTC.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull ARM cpuidle changes for v4.7 from Daniel Lezcano.
* 'cpuidle/4.7' of http://git.linaro.org/people/daniel.lezcano/linux:
drivers: firmware: psci: use const and __initconst for psci_cpuidle_ops
soc: qcom: spm: Use const and __initconst for qcom_cpuidle_ops
ARM: cpuidle: constify return value of arm_cpuidle_get_ops()
ARM: cpuidle: add const qualifier to cpuidle_ops member in structures
to the clk-ti branch from the Linux clk tree for the ADPLL clock driver.
Otherwise things won't keep booting properly when we flip over to use
the clock driver instead of fixed clocks set up by the bootloader.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2Lew
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.6/dt-ti81xx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Enable dm814x and dra62x clock driver. This branch has a dependency
to the clk-ti branch from the Linux clk tree for the ADPLL clock driver.
Otherwise things won't keep booting properly when we flip over to use
the clock driver instead of fixed clocks set up by the bootloader.
* tag 'omap-for-v4.6/dt-ti81xx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Add clocks for dm814x ADPLL
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Put nodes after of_address_to_resource() in case the nodes might be
released while parsing in them.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Drop support for Cortex A8 in timer code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6ZAq
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Merge "Renesas ARM Based SoC Updates for v4.7" from Simon Horman:
Drop support for Cortex A8 in timer code
* tag 'renesas-soc-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: timer: Drop support for Cortex A8
ARM: shmobile: timer: Fix preset_lpj leading to too short delays
Revert "ARM: dts: porter: Enable SCIF_CLK frequency and pins"
ARM: dts: r8a7791: Don't disable referenced optional clocks
preparatory patches to support a USB PHY
driver for USB on DA850 SoC. This should
eventually lead to USB working again on
this device.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=BpdJ
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v4.7/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/soc
Merge "DaVinci SoC updates for v4.7" from Sekhar Nori:
These are preparatory patches to support a USB PHY driver for USB on DA850
SoC. This should eventually lead to USB working again on this device.
* tag 'davinci-for-v4.7/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: clk: add set_parent callback for mux clocks
ARM: davinci: da8xx: move usb code to new file
ARM: davinci: use IRQCHIP_DECLARE for cp_intc
ARM: davinci: remove unused DA8XX_NUM_UARTS
ARM: davinci: simplify call to of populate
ARM: DaVinci USB: removed deprecated properties from MUSB config
removal of some unused macros and data-
-structures and use of helper macros to
reduce code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iQIcBAABAgAGBQJXEMhfAAoJEGFBu2jqvgRNwfMP/ivleJx1UhZshbdKEnR4f4M1
/yWtsMwVToJfHA428EAFoeUH3SJXX3MOLkaBdP8755QN97ot1Oa9Szfmd/Ld5OSi
RRYulICYeNfbIiZPzEQZxZq4x41VvlVQDi+GdSqB0SC/GzH4IaeZ2kC44pTmEgqj
hj5KHsIZuqr7JetVm8mnw776c8YZ3my+napwyKi3HK9gF/P1nf5mvVg6ZKtkOfIL
nJqhpkidDfqjDdnuhf/CJSwvhvZsSD1QCYIpSu8oT2afT3epUERKdQ/6rnsz5176
N4oZge3wid3nfLUr+2VU/1EBPCfD4DNIjnni0/l1I0aQ3F2NVfre/J9tYhSc+YEv
XIiTg5rRrZ+CyVm9Lz97fYXR+HagVCQzOhXJlvpHS9yqw2oYz/FsemiOPyzPFFs7
l08jNAY8kXAI2gKMpjHQENK6EP4fBXbex7sHRsLeVgCDVMo5kBXsU/dbQreZSEZ7
vjq2yn4+VXlAbLoCWBzFxCEk8BowZDMETPB7q/HLvj2wUe5uY9N17vJnmVUaW+yW
6QlGWIcAufvQAEN6564t1FiDondaDcmqgYaLLn+cFXuvntiOwJw1STCv9aMu0iuW
8G5i0B7/3zVrVqxbbLBwpkGmDqcohIr8wZnXQnCqLk+Z4NMMEnpRQByx+zrb8g11
en97Fx7GYTj+qU1kCpzl
=uaz5
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v4.7/cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/cleanup
Merge "DaVinci cleanups for v4.7" from Sekhar Nori:
It includes removal of some unused macros and data- -structures and use
of helper macros to reduce code.
* tag 'davinci-for-v4.7/cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: use IRQCHIP_DECLARE for cp_intc
ARM: davinci: remove unused DA8XX_NUM_UARTS
ARM: davinci: simplify call to of populate
ARM: DaVinci USB: removed deprecated properties from MUSB config
- Justin adds a soc_dev driver to properly report to user-space the Broadcom
STB SoC family, product and revision
- Florian reworks how the brcmstb_gisb driver dependency is done to enable it
on Broadcom STB MIPS-based SoCs and remove a select in
arch/arm/mach-bcm/Kconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OJuu
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.7/drivers' of http://github.com/Broadcom/stblinux into next/drivers
Merge "Broadcom ARM-based SoCs drivers changes" from Florian Fainelli:
- Justin adds a soc_dev driver to properly report to user-space the Broadcom
STB SoC family, product and revision
- Florian reworks how the brcmstb_gisb driver dependency is done to enable it
on Broadcom STB MIPS-based SoCs and remove a select in
arch/arm/mach-bcm/Kconfig
* tag 'arm-soc/for-4.7/drivers' of http://github.com/Broadcom/stblinux:
bus: brcmstb_gisb: Rework dependencies
soc: brcmstb: add SoC driver to brcmstb
This contains a bunch of preparatory patches to the PMC driver which are
a prerequisite to moving the driver to generic power domains.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=EmlG
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.7-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
Merge "soc/tegra: Changes for v4.7-rc1" from Thierry Reding:
This contains a bunch of preparatory patches to the PMC driver which are
a prerequisite to moving the driver to generic power domains.
* tag 'tegra-for-4.7-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: Update NVIDIA PMC for Tegra
soc/tegra: pmc: Wait for powergate state to change
soc/tegra: pmc: Ensure GPU partition can be toggled on/off by PMC
soc/tegra: pmc: Remove additional check for a valid partition
soc/tegra: pmc: Fix verification of valid partitions
soc/tegra: pmc: Fix testing of powergate state
soc/tegra: pmc: Change powergate and rail IDs to be an unsigned type
soc/tegra: pmc: Protect public functions from potential race conditions
soc/tegra: pmc: Restore base address on probe failure
soc/tegra: pmc: Remove non-existing L2 partition for Tegra124
soc/tegra: pmc: Remove non-existing power partitions for Tegra210
soc/tegra: pmc: Remove debugfs entry on probe failure
soc/tegra: pmc: Fix sparse warning for tegra_pmc_init_tsense_reset()
soc/tegra: pmc: Add missing structure members to kernel-doc
for Versatile flash handling and instead moving it over
to the device tree and a special add-on file.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9Fgt
-----END PGP SIGNATURE-----
Merge tag 'versatile-flash-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/drivers
Merge "move Versatile flash protection to the device tree" from Linus Walleij:
This is a set of patches removing the board file code
for Versatile flash handling and instead moving it over
to the device tree and a special add-on file.
* tag 'versatile-flash-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: integrator: move flash registration to device tree
ARM: versatile: move flash registration to the device tree
mtd: augment the "arm,versatile-flash" bindings
mtd: physmap_of: add a hook for Versatile write protection
Acked-by: Brian Norris <computersforpeace@gmail.com>
1. Support for external expansion bus useful for additional hardware
e.g. LogicTile Express daughterboards (Brian Starkey)
2. Fix for device node name unit-address presence/absence warnings
enabled in recently update DTC (Sudeep Holla)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=CN/A
-----END PGP SIGNATURE-----
Merge tag 'vexpress-for-v4.7/updates' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/dt
Merge "ARMv7 Vexpress updates/fixes for v4.7" from Sudeep Holla:
1. Support for external expansion bus useful for additional hardware
e.g. LogicTile Express daughterboards (Brian Starkey)
2. Fix for device node name unit-address presence/absence warnings
enabled in recently update DTC (Sudeep Holla)
* tag 'vexpress-for-v4.7/updates' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
ARM: dts: vexpress: Add external expansion bus to DT
ARM: dts: vexpress: fix node name unit-address presence warnings
* Configure NMI key as wakeup source in DT of kzm9g board
* Add SDHI support to DT of gose board
* Add support of UHS-I SDR-50 for SDHI to DT of r8a7790 SoC
* Correct interrupt type for ARM TWD in DT of r8a7779 and sh73a0 SoCs
* Add IIC support to DT of r8a7794 SoC
* Add CAN support to DT of r8a7793 and r8a7794 SoCs
* Add SCIF2 support to r8a7790 device tree
* Use CAN, JPU and USB3.0 fallback compatibility string
in DT of r8a7791 and r8a7790 SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vStA
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Renesas ARM Based SoC DT Updates for v4.7" from Simon Horman:
* Configure NMI key as wakeup source in DT of kzm9g board
* Add SDHI support to DT of gose board
* Add support of UHS-I SDR-50 for SDHI to DT of r8a7790 SoC
* Correct interrupt type for ARM TWD in DT of r8a7779 and sh73a0 SoCs
* Add IIC support to DT of r8a7794 SoC
* Add CAN support to DT of r8a7793 and r8a7794 SoCs
* Add SCIF2 support to r8a7790 device tree
* Use CAN, JPU and USB3.0 fallback compatibility string
in DT of r8a7791 and r8a7790 SoCs
* tag 'renesas-dt-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (22 commits)
ARM: dts: gose: Enable SDHI controllers
ARM: dts: r8a7793: Add SDHI controllers
ARM: dts: r8a7790: fix max-frequency for SDHI
ARM: dts: kzm9g: Configure NMI key as wake-up source
ARM: dts: r8a7790: lager: Enable UHS-I SDR-50
ARM: dts: r8a7790: Set maximum frequencies for SDHI clocks
ARM: dts: r8a7791: Use USB3.0 fallback compatibility string
ARM: dts: r8a7790: Use USB3.0 fallback compatibility string
ARM: dts: r8a7779: Correct interrupt type for ARM TWD
ARM: dts: sh73a0: Correct interrupt type for ARM TWD
ARM: dts: r8a7794: Add IIC nodes
ARM: dts: r8a7794: add IIC clocks
ARM: dts: r8a7793: add CAN nodes to device tree
ARM: dts: r8a7793: add CAN clocks to device tree
ARM: dts: r8a7794: add CAN nodes to device tree
ARM: dts: r8a7794: add CAN clocks to device tree
ARM: dts: r8a7790: use fallback can compatibility string
ARM: dts: r8a7791: use fallback can compatibility string
ARM: dts: r8a7790: Add SCIF2 device node
ARM: dts: r8a7790: Add SCIF2 clock
...
- Eric enables more BCM2835 peripherals in multi_v7_defconfig: watchdog, I2S,
switches from the sdhci-bcm2835 to the sdhci-iproc driver, DWC2 USB controller
- Eric also enables more BCM2835 peripherals in bcm2835_defconfig: VC4, NFS root
Power Management support, switching sdhci-bcm2835 for sdhci-iproc
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QxkI
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.7/defconfig' of http://github.com/Broadcom/stblinux into next/defconfig
Merge "This pull request contains defconfig changes for Broadcom ARM-based SoCs"
from Florian Fainelli:
- Eric enables more BCM2835 peripherals in multi_v7_defconfig: watchdog, I2S,
switches from the sdhci-bcm2835 to the sdhci-iproc driver, DWC2 USB controller
- Eric also enables more BCM2835 peripherals in bcm2835_defconfig: VC4, NFS root
Power Management support, switching sdhci-bcm2835 for sdhci-iproc
* tag 'arm-soc/for-4.7/defconfig' of http://github.com/Broadcom/stblinux:
ARM: bcm2835: Enable NFS root support.
ARM: bcm2835: Enable the VC4 graphics driver in the defconfig
ARM: bcm2835: Enable CONFIG_PM.
ARM: bcm2835: Switch BCM2835 to sdhci-iproc.c for MMC
ARM: multi_v7_defconfig: Build in DWC2 USB support
ARM: multi_v7_defconfig: Switch BCM2835 to sdhci-iproc.c for MMC
ARM: multi_v7_defconfig: Add more BCM2835 support
- Use the new cryto engine(mv_cesa) in the mvebu and multi-arm
defcongig files
- Attach mvebu_*_defconfig to the mvebu maintainers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlcPzQsACgkQCwYYjhRyO9UpUwCghNZsWe0jSWCZyVbmLS4qCGT/
X3oAn1wc1CeLHFDroMVcCw3aBaTLofUP
=LxX6
-----END PGP SIGNATURE-----
Merge tag 'mvebu-defconfig-4.7-1' of git://git.infradead.org/linux-mvebu into next/defconfig
Merge "mvebu defconfig for 4.7 (part 1)" from Gregory CLEMENT
- Use the new cryto engine(mv_cesa) in the mvebu and multi-arm
defcongig files
- Attach mvebu_*_defconfig to the mvebu maintainers
* tag 'mvebu-defconfig-4.7-1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu_v5_defconfig: Switching to the new Marvell's cryptographic engine driver
ARM: multi_v7_defconfig: Enabling the new Marvell's cryptographic engine driver
MAINTAINERS: attach arch/arm/configs/mvebu_*_defconfig to relevant maintainers
ARM: mvebu_v7_defconfig: Enabling the new Marvell's cryptographic engine driver
This NAND controller device is used on UniPhier SoCs (and I know
it is also used on SoC FPGA).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
to the clk-ti branch from the Linux clk tree for the ADPLL clock driver.
Otherwise things won't keep booting properly when we flip over to use
the clock driver instead of fixed clocks set up by the bootloader.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJW2MN/AAoJEBvUPslcq6VzVqEP/A2qxFhMYyf/q0Za54RNRHjj
iHbpxmfPUrFIGO/IQqkk7bl5Ufgs+L+uW+mjoe0CvIYGEoVDY/cfe3AZW734cGMO
rLbs3CovoHst2UTZbcKVRs/QjkN+R9nvowvvqK87vSbpAbMX7pRrEcfZSN77T4ej
vRbtRyD0msNCm8s0TgdpQ6ObK0GHmfqtq3GFA/g5Rs5m1X7h9PaD+PWUsVDugKyM
9bEmGZSyOaRN5qGrOX/PTTKK3OiCOSJXB/8tnRgNW7DaISop+KJwxzMhBHyx2iKP
JaD5lDJk/ArE+4Za0FmSpug8muUHLHH+htCu76uU6qi/s7+q8g9UR9ewzfLg7/rG
wYl8IwDBVxWbi5PLnHPRrghGheEkM2ykiqEp5DqlZ1B7vfGv4Wl/3ZxiL1ZO5FZv
jre1yHm5sguLCtA6BErWi69SCI3rpi4GrDQuYnlAbg9ABRH+YBVZ+3lCqtBVyh6J
5yHexIELEEOUHHT2KLPNi7HexzK6xtMpsh4QlP1Yxt2o6dVI2LmTS+oKtU6QAjSn
WE5pbLd9XZUBaDO4jw3T01edhGVpf2OxmtGSOd/ptF5JjZoDA2Kg+NcDE0eTPL72
v7yVlNVU3g8PlD1EfRENi/KL0K4GLNq3eT2WCFQYp/nYuN1dVkk5xraEv3w7N0iZ
vGlh9twbt7VvjiGoImcF
=2Lew
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.6/dt-ti81xx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Enable dm814x and dra62x clock driver. This branch has a dependency
to the clk-ti branch from the Linux clk tree for the ADPLL clock driver.
Otherwise things won't keep booting properly when we flip over to use
the clock driver instead of fixed clocks set up by the bootloader.
* tag 'omap-for-v4.6/dt-ti81xx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Add clocks for dm814x ADPLL
The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform
device now, reuse that and remove similar code from platform code.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform
device now, reuse that and remove similar code from platform code.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform
device now, reuse that and remove similar code from platform code.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch add rockchip's compatible string to the compat list and
remove similar code from platform code for supporting generic platdev
driver.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform
device now, reuse that and remove similar code from platform code.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform
device now, reuse that and remove similar code from platform code.
Note that the complete routine imx27_dt_init() is removed as
of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
has same effect as a NULL .init_machine machine callback pointer.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform
device now, reuse that and remove similar code from platform code.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Marcel Ziswiler