Patch here adds cpu hotplug functions to hv_24x7 pmu.
A new cpuhp_state "CPUHP_AP_PERF_POWERPC_HV_24x7_ONLINE" enum
is added.
The online callback function updates the cpumask only if its
empty. As the primary intention of adding hotplug support
is to designate a CPU to make HCALL to collect the
counter data.
The offline function test and clear corresponding cpu in a cpumask
and update cpumask to any other active cpu.
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200709051836.723765-2-kjain@linux.ibm.com
pseries_update_drconf_memory() runs from a DT notifier in response to
an update to the ibm,dynamic-memory property of the
/ibm,dynamic-reconfiguration-memory node. This property is an older
less compact format than the ibm,dynamic-memory-v2 property used in
most currently supported firmwares. There has never been an equivalent
function for the v2 property.
pseries_update_drconf_memory() compares the 'assigned' flag for each
LMB in the old vs new properties and adds or removes the block
accordingly. However it appears to be of no actual utility:
* Partition suspension and PRRNs are specified only to change LMBs'
NUMA affinity information. This notifier should be a no-op for those
scenarios since the assigned flags should not change.
* The memory hotplug/DLPAR path has a hack which short-circuits
execution of the notifier:
dlpar_memory()
...
rtas_hp_event = true;
drmem_update_dt()
of_update_property()
pseries_memory_notifier()
pseries_update_drconf_memory()
if (rtas_hp_event) return;
So this code only makes sense as a relic of the time when more of the
DLPAR workflow took place in user space. I don't see a purpose for it
now.
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200612051238.1007764-19-nathanl@linux.ibm.com
dlpar_memory() no longer has any callers which pass
PSERIES_HP_ELOG_ACTION_READD. Remove this case and the corresponding
unreachable code.
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200612051238.1007764-17-nathanl@linux.ibm.com
pseries_devicetree_update() is no longer called with PRRN_SCOPE. The
purpose of prrn_update_node() was to remove and then add back a LMB
whose NUMA assignment had changed. This has never been reliable, and
this codepath has been default-disabled for several releases. Remove
prrn_update_node().
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200612051238.1007764-16-nathanl@linux.ibm.com
Since arch_update_cpu_topology() doesn't do anything on powerpc now,
remove it and associated dead code.
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200612051238.1007764-15-nathanl@linux.ibm.com
All users of this prrn_is_enabled() are gone; remove it.
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200612051238.1007764-14-nathanl@linux.ibm.com
prrn_is_enabled() always returns false/0, so handle_rtas_event() can
be simplified and some dead code can be removed. Use machine_is()
instead of #ifdef to run this code only on pseries, and add an
informational ratelimited message that we are ignoring the
events. PRRN events are relatively rare in normal operation and
usually arise from operator-initiated actions such as a DPO (Dynamic
Platform Optimizer) run.
Eventually we do want to consume these events and update the device
tree, but that needs more care to be safe vs LPM and DLPAR.
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200612051238.1007764-13-nathanl@linux.ibm.com
These APIs have become no-ops, so remove them and all call sites.
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200612051238.1007764-12-nathanl@linux.ibm.com
timed_topology_update is a no-op now, so remove it and all call sites.
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200612051238.1007764-11-nathanl@linux.ibm.com
Previous changes have removed the code which sets bits in
cpu_associativity_changes_mask and thus it is never modifed at
runtime. From this we can reason that numa_update_cpu_topology()
always returns 0 without doing anything. Remove the body of
numa_update_cpu_topology() and remove all code which becomes
unreachable as a result.
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200612051238.1007764-10-nathanl@linux.ibm.com
These flags are always zero now; remove them and suitably adjust the
remaining references to them.
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200612051238.1007764-9-nathanl@linux.ibm.com
Since vphn_enabled is always 0, we can remove the call to
topology_schedule_update() and remove the code which becomes
unreachable as a result.
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200612051238.1007764-8-nathanl@linux.ibm.com
Since vphn_enabled is always 0, we can stub out
timed_topology_update() and remove the code which becomes unreachable.
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200612051238.1007764-7-nathanl@linux.ibm.com
Previous changes have made it so these flags are never changed;
enforce this by making them const.
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200612051238.1007764-6-nathanl@linux.ibm.com
Since the topology_updates_enabled flag is now always false, remove it
and the code which has become unreachable. This is the minimum change
that prevents 'defined but unused' warnings emitted by the compiler
after stubbing out the start/stop_topology_updates() functions.
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200612051238.1007764-5-nathanl@linux.ibm.com
Remove the /proc/powerpc/topology_updates interface and the
topology_updates=on/off command line argument. The internal
topology_updates_enabled flag remains for now, but always false.
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200612051238.1007764-4-nathanl@linux.ibm.com
Partition suspension, used for hibernation and migration, requires
that the OS place all but one of the LPAR's processor threads into one
of two states prior to calling the ibm,suspend-me RTAS function:
* the architected offline state (via RTAS stop-self); or
* the H_JOIN hcall, which does not return until the partition
resumes execution
Using H_CEDE as the offline mode, introduced by
commit 3aa565f53c ("powerpc/pseries: Add hooks to put the CPU into
an appropriate offline state"), means that any threads which are
offline from Linux's point of view must be moved to one of those two
states before a partition suspension can proceed.
This was eventually addressed in commit 120496ac2d ("powerpc: Bring
all threads online prior to migration/hibernation"), which added code
to temporarily bring up any offline processor threads so they can call
H_JOIN. Conceptually this is fine, but the implementation has had
multiple races with cpu hotplug operations initiated from user
space[1][2][3], the error handling is fragile, and it generates
user-visible cpu hotplug events which is a lot of noise for a platform
feature that's supposed to minimize disruption to workloads.
With commit 3aa565f53c ("powerpc/pseries: Add hooks to put the CPU
into an appropriate offline state") reverted, this code becomes
unnecessary, so remove it. Since any offline CPUs now are truly
offline from the platform's point of view, it is no longer necessary
to bring up CPUs only to have them call H_JOIN and then go offline
again upon resuming. Only active threads are required to call H_JOIN;
stopped threads can be left alone.
[1] commit a6717c01dd ("powerpc/rtas: use device model APIs and
serialization during LPM")
[2] commit 9fb603050f ("powerpc/rtas: retry when cpu offline races
with suspend/migration")
[3] commit dfd718a2ed ("powerpc/rtas: Fix a potential race between
CPU-Offline & Migration")
Fixes: 120496ac2d ("powerpc: Bring all threads online prior to migration/hibernation")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200612051238.1007764-3-nathanl@linux.ibm.com
This effectively reverts commit 3aa565f53c ("powerpc/pseries: Add
hooks to put the CPU into an appropriate offline state"), which added
an offline mode for CPUs which uses the H_CEDE hcall instead of the
architected stop-self RTAS function in order to facilitate "folding"
of dedicated mode processors on PowerVM platforms to achieve energy
savings. This has been the default offline mode since its
introduction.
There's nothing about stop-self that would prevent the hypervisor from
achieving the energy savings available via H_CEDE, so the original
premise of this change appears to be flawed.
I also have encountered the claim that the transition to and from
ceded state is much faster than stop-self/start-cpu. Certainly we
would not want to use stop-self as an *idle* mode. That is what H_CEDE
is for. However, this difference is insignificant in the context of
Linux CPU hotplug, where the latency of an offline or online operation
on current systems is on the order of 100ms, mainly attributable to
all the various subsystems' cpuhp callbacks.
The cede offline mode also prevents accurate accounting, as discussed
before:
https://lore.kernel.org/linuxppc-dev/1571740391-3251-1-git-send-email-ego@linux.vnet.ibm.com/
Unconditionally use stop-self to offline processor threads. This is
the architected method for offlining CPUs on PAPR systems.
The "cede_offline" boot parameter is rendered obsolete.
Removing this code enables the removal of the partition suspend code
which temporarily onlines all present CPUs.
Fixes: 3aa565f53c ("powerpc/pseries: Add hooks to put the CPU into an appropriate offline state")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200612051238.1007764-2-nathanl@linux.ibm.com
If both count cache and link stack are to be flushed, and can be flushed
with the special bcctr, patch that in directly to the flush/branch nop
site.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200609070610.846703-7-npiggin@gmail.com
Branch cache flushing code patching has inter-dependencies on both the
link stack and the count cache flushing state.
To make the code clearer and to separate the link stack and count
cache handling, split the "toggle" (setting up variables and printing
enable/disable) from the code patching.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Always print something, even if the flush is disabled]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200609070610.846703-5-npiggin@gmail.com
Prepare to allow for hardware link stack flushing by using the
none/sw/hw type, same as the count cache state.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200609070610.846703-3-npiggin@gmail.com
The count cache flush mostly refers to both count cache and link stack
flushing. As a first step to untangling these a bit, re-name the bits
that apply to both.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200609070610.846703-2-npiggin@gmail.com
When a FP/VEC/VSX unavailable fault loads registers and enables the
facility in the MSR, re-set the lazy restore counters to 1 rather
than incrementing them so every fault gets the same number of
restores before the next fault.
This probably shouldn't be a practical change because if a lazy counter
was non-zero then it should have been restored and would not cause a
fault when userspace tries to access it. However the code and comment
implies otherwise so that's misleading and unnecessary.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200623234139.2262227-3-npiggin@gmail.com
Before returning to user, if there are missing FP/VEC/VSX bits from the
user MSR then those registers had been saved and must be restored again
before use. restore_math will decide whether to restore immediately, or
skip the restore and let fp/vec/vsx unavailable faults demand load the
registers.
Each time restore_math restores one of the FP/VSX or VEC register sets
is loaded, an 8-bit counter is incremented (load_fp and load_vec). When
these wrap to zero, restore_math no longer restores that register set
until after they are next demand faulted.
It's quite usual for those counters to have different values, so if one
wraps to zero and restore_math no longer restores its registers or user
MSR bit but the other is not zero yet does not need to be restored
(because the kernel is not frequently using the FPU), then restore_math
will be called and it will also not return in the early exit check.
This causes msr_check_and_set to test and set the MSR at every kernel
exit despite having no work to do.
This can cause workloads (e.g., a NULL syscall microbenchmark) to run
fast for a time while both counters are non-zero, then slow down when
one of the counters reaches zero, then speed up again after the second
counter reaches zero. The cost is significant, about 10% slowdown on a
NULL syscall benchmark, and the jittery behaviour is very undesirable.
Fix this by having restore_math test all conditions first, and only
update MSR if we will be loading registers.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200623234139.2262227-2-npiggin@gmail.com
The TM test in restore_math added by commit dc16b553c9 ("powerpc:
Always restore FPU/VEC/VSX if hardware transactional memory in use") is
no longer necessary after commit a8318c13e7 ("powerpc/tm: Fix
restoring FP/VMX facility incorrectly on interrupts"), which removed
the cases where restore_math has to restore if TM is active.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200623234139.2262227-1-npiggin@gmail.com
With kernel now supporting new pmem flush/sync instructions, we can now
enable the kernel to initialize the device. On P10 these devices would
appear with a new compatible string. For PAPR device we have
compatible "ibm,pmemory-v2"
and for OF pmem device we have
compatible "pmem-region-v2"
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200701072235.223558-8-aneesh.kumar@linux.ibm.com
nvdimm expect the flush routines to just mark the cache clean. The barrier
that mark the store globally visible is done in nvdimm_flush().
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200701072235.223558-7-aneesh.kumar@linux.ibm.com
pmem on POWER10 can now use phwsync instead of hwsync to ensure
all previous writes are architecturally visible for the platform
buffer flush.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200701072235.223558-6-aneesh.kumar@linux.ibm.com
Architectures like ppc64 provide persistent memory specific barriers
that will ensure that all stores for which the modifications are
written to persistent storage by preceding dcbfps and dcbstps
instructions have updated persistent storage before any data
access or data transfer caused by subsequent instructions is initiated.
This is in addition to the ordering done by wmb()
Update nvdimm core such that architecture can use barriers other than
wmb to ensure all previous writes are architecturally visible for
the platform buffer flush.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200701072235.223558-5-aneesh.kumar@linux.ibm.com
Start using dcbstps; phwsync; sequence for flushing persistent memory range.
The new instructions are implemented as a variant of dcbf and hwsync and on
P8 and P9 they will be executed as those instructions. We avoid using them on
older hardware. This helps to avoid difficult to debug bugs.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200701072235.223558-4-aneesh.kumar@linux.ibm.com
POWER10 introduces two new variants of dcbf instructions (dcbstps and dcbfps)
that can be used to write modified locations back to persistent storage.
Additionally, POWER10 also introduce phwsync and plwsync which can be used
to establish order of these writes to persistent storage.
This patch exposes these instructions to the rest of the kernel. The existing
dcbf and hwsync instructions in P8 and P9 are adequate to enable appropriate
synchronization with OpenCAPI-hosted persistent storage. Hence the new
instructions are added as a variant of the old ones that old hardware
won't differentiate.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200701072235.223558-3-aneesh.kumar@linux.ibm.com
The PAPR based virtualized persistent memory devices are only supported on
POWER9 and above. In the followup patch, the kernel will switch the persistent
memory cache flush functions to use a new `dcbf` variant instruction. The new
instructions even though added in ISA 3.1 works even on P8 and P9 because these
are implemented as a variant of existing `dcbf` and `hwsync` and on P8 and
P9 behaves as such.
Considering these devices are only supported on P8 and above, update the driver
to prevent a P7-compat guest from using persistent memory devices.
We don't update of_pmem driver with the same condition, because, on bare-metal,
the firmware enables pmem support only on P9 and above. There the kernel depends
on OPAL firmware to restrict exposing persistent memory related device tree
entries on older hardware. of_pmem.ko is written without any arch dependency and
we don't want to add ppc64 specific cpu feature check in of_pmem driver.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200701072235.223558-2-aneesh.kumar@linux.ibm.com
When platform doesn't support GTSE, let TLB invalidation requests
for radix guests be off-loaded to the host using H_RPT_INVALIDATE
hcall.
[hcall wrapper, error path handling and renames]
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Bharata B Rao <bharata@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200703053608.12884-4-bharata@linux.ibm.com
H_REGISTER_PROC_TBL asks for GTSE by default. GTSE flag bit should
be set only when GTSE is supported.
Signed-off-by: Bharata B Rao <bharata@linux.ibm.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200703053608.12884-3-bharata@linux.ibm.com
Make GTSE an MMU feature and enable it by default for radix.
However for guest, conditionally enable it if hypervisor supports
it via OV5 vector. Let prom_init ask for radix GTSE only if the
support exists.
Having GTSE as an MMU feature will make it easy to enable radix
without GTSE. Currently radix assumes GTSE is enabled by default.
Signed-off-by: Bharata B Rao <bharata@linux.ibm.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200703053608.12884-2-bharata@linux.ibm.com
save_general_regs() which does special handling when i == PT_SOFTE.
Rewrite it to minimise the specific part, especially the __put_user()
and associated error handling is the same so make it common.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
[mpe: Use a regular if rather than ternary operator]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/47a38df46cae5a5a88a558a64d71f75e9c4d9950.1594125164.git.christophe.leroy@csgroup.eu
Since commit ("1bd79336a426 powerpc: Fix various
syscall/signal/swapcontext bugs"), getting save_general_regs() called
without FULL_REGS() is very unlikely and generates a warning.
The 32-bit version of save_general_regs() doesn't take care of it
at all and copies all registers anyway since that commit.
Moreover, commit 965dd3ad30 ("powerpc/64/syscall: Remove
non-volatile GPR save optimisation") is another reason why it would
never happen.
So the same with 64-bit, don't worry about FULL_REGS() and copy
all registers all the time.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/173de3b659fa3a5f126a0eb170522cccd909950f.1594125164.git.christophe.leroy@csgroup.eu
Documentation wrongly tells that book3s/32 CPU have hash MMU.
603 and e300 core only have software loaded TLB.
755, 7450 family and e600 core have both hash MMU and software loaded
TLB. This can be selected by setting a bit in HID2 (755) or
HID0 (others). At the time being this is not supported by the kernel.
Make this explicit in the documentation.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/261923c075d1cb49d02493685e8585d4ea2a5197.1593698951.git.christophe.leroy@csgroup.eu
Returning from an interrupt or syscall to a signal handler currently
begins execution directly at the handler's entry point, with LR set to
the address of the sigreturn trampoline. When the signal handler
function returns, it runs the trampoline. It looks like this:
# interrupt at user address xyz
# kernel stuff... signal is raised
rfid
# void handler(int sig)
addis 2,12,.TOC.-.LCF0@ha
addi 2,2,.TOC.-.LCF0@l
mflr 0
std 0,16(1)
stdu 1,-96(1)
# handler stuff
ld 0,16(1)
mtlr 0
blr
# __kernel_sigtramp_rt64
addi r1,r1,__SIGNAL_FRAMESIZE
li r0,__NR_rt_sigreturn
sc
# kernel executes rt_sigreturn
rfid
# back to user address xyz
Note the blr with no matching bl. This can corrupt the return
predictor.
Solve this by instead resuming execution at the signal trampoline
which then calls the signal handler. qtrace-tools link_stack checker
confirms the entire user/kernel/vdso cycle is balanced after this
patch, whereas it's not upstream.
Alan confirms the dwarf unwind info still looks good. gdb still
recognises the signal frame and can step into parent frames if it
break inside a signal handler.
Performance is pretty noisy, not a very significant change on a POWER9
here, but branch misses are consistently a lot lower on a
microbenchmark:
Performance counter stats for './signal':
13,085.72 msec task-clock # 1.000 CPUs utilized
45,024,760,101 cycles # 3.441 GHz
65,102,895,542 instructions # 1.45 insn per cycle
11,271,673,787 branches # 861.372 M/sec
59,468,979 branch-misses # 0.53% of all branches
12,989.09 msec task-clock # 1.000 CPUs utilized
44,692,719,559 cycles # 3.441 GHz
65,109,984,964 instructions # 1.46 insn per cycle
11,282,136,057 branches # 868.585 M/sec
39,786,942 branch-misses # 0.35% of all branches
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200511101952.1463138-1-npiggin@gmail.com
The kernel test robot pointed out a slightly different error message
after recent commit 5456ffdee6 ("powerpc/spufs: simplify spufs core
dumping") to spufs for a configuration that never worked:
powerpc64-linux-ld: arch/powerpc/platforms/cell/spufs/file.o: in function `.spufs_proxydma_info_dump':
>> file.c:(.text+0x4c68): undefined reference to `.dump_emit'
powerpc64-linux-ld: arch/powerpc/platforms/cell/spufs/file.o: in function `.spufs_dma_info_dump':
file.c:(.text+0x4d70): undefined reference to `.dump_emit'
powerpc64-linux-ld: arch/powerpc/platforms/cell/spufs/file.o: in function `.spufs_wbox_info_dump':
file.c:(.text+0x4df4): undefined reference to `.dump_emit'
Add a Kconfig dependency to prevent this from happening again.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200706132302.3885935-1-arnd@arndb.de
pnv_ioda_setup_bus_dma() is only used when a passed through PE is
returned to the host. If the kernel is built without IOMMU support
this is dead code. Move it under the #ifdef with the rest of the
IOMMU API support.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200705133557.443607-2-oohall@gmail.com
The kernel test robot noticed these are non-static which causes Clang to
print some warnings. These are called via ppc_md function pointers so
there's no need for them to be non-static.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200705133557.443607-1-oohall@gmail.com
Kajol Jain