There is a typo in the definition of IDMA64C_CFGH_WR_ISSUE_THD(x). Fix it by
swapping characters.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The mxs-dma unit is also available on i.MX6UL. Make it possible to
select it in Kconfig.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In order to avoid possible race condition when client drivers are using
dmaengine_terminate_sync() call to disable the channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We need the callback to support the dmaengine_terminate_sync().
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We need the callback to support the dmaengine_terminate_sync().
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Future IOATDMA hardware will take advantage of descriptors residing in
contiguous memory. Setting the descriptor ring in max config DMA memory
of 2MB. Each channel will need 2 of these chunks. This should provide 64k
of 64B descriptors.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Moving to contingous memory backed descriptor rings. This makes is really
difficult and complex to do reshape. Going to remove this as I don't think
we need to do it anymore.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Converting old pci_pool_* calls to "new" dma_pool_* to make everything
uniform.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The commit 2895b2cad6 ("dmaengine: dw: fix cyclic transfer callbacks")
re-enabled BLOCK interrupts with regard to make cyclic transfers work. However,
this change becomes a regression for non-cyclic transfers as interrupt counters
under stress test had been grown enormously (approximately per 4-5 bytes in the
UART loop back test).
Taking into consideration above enable BLOCK interrupts if and only if channel
is programmed to perform cyclic transfer.
Fixes: 2895b2cad6 ("dmaengine: dw: fix cyclic transfer callbacks")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mans Rullgard <mans@mansr.com>
Tested-by: Mans Rullgard <mans@mansr.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The datasheet requires that the user must clear LLP_[SD]_EN bits whenever
LLP.LOC is zero, i.e. in the last descriptor of a multi-block chain.
Make the driver do this.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch add max burst capability for dmaengine and
limit burst capability to one for PL330_QUIRK_BROKEN_NO_FLUSHP
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch add max_burst to dma_get_slave_caps for clients
to get the burst capability of slave dma controller.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch add "arm,pl330-broken-no-flushp" quirk to avoid execute
DMAFLUSHP if Soc doesn't support it.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
cc: Doug Anderson <dianders@chromium.org>
cc: Heiko Stuebner <heiko@sntech.de>
cc: Olof Johansson <olof@lixom.net>
Reviewed-by: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds to support burst mode for dev-to-mem and
mem-to-dev transmit.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
cc: Heiko Stuebner <heiko@sntech.de>
cc: Doug Anderson <dianders@chromium.org>
cc: Olof Johansson <olof@lixom.net>
Reviewed-by: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When retrieving the residue value, the SRC/DST fields of the
active PaRAM are read to determine the current position of
the DMA engine. However, the AM335x Technical Reference Manual
states:
11.3.3.6 Parameter Set Updates
After the TR is read from the PaRAM (and is in the process
of being submitted to the EDMA3TC), the following fields are
updated as needed: ... SRC DST
This means SRC/DST is incremented even though the DMA transfer
may not have started yet or is in progress. Thus if the reader
of the residue accesses the DMA buffer too quickly, the CPU is
misinformed about the data that has been successfully processed.
The CCSTAT.ACTV register is a boolean that is set if any TR is
being processed by either the EMDA3CC or EDMA3TC. By polling
this register it is possible to ensure that the residue value
returned is valid for immediate processing. However, since the
DMA engine may be active, polling may never hit a moment where
no TR is being processed. To handle this, the SRC/DST is also
polled to see if it changes. And as a last resort, a max loop
count for the busy waiting exists to avoid an infinite loop.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
WildcatPoint PCH as seen on MacBook 12-inch (Early 2015) has PCI enabled
DesignWare DMA controller. Enable it by adding its ID to the corresponding
driver.
Reported-by: Leif Liddy <leif.liddy@gmail.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=110901
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The timer_event() function seems to have a bug where it ends up marking the
last entry as non-responding and eventually attempts to restart the
channel. This also continuously happen when idle. What needs to happen is
for us to make sure there are no descriptors active and then handle that
case properly. We should only hit the "cleanup" stage if there are still
active descriptors.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
CC [M] drivers/dma/ioat/prep.o
drivers/dma/ioat/prep.c: In function 'ioat_prep_pqxor':
drivers/dma/ioat/prep.c:682:1: warning: the frame size of 1048 bytes is larger than 1024 bytes [-Wframe-larger-than=]
}
^
drivers/dma/ioat/prep.c: In function 'ioat_prep_pqxor_val':
drivers/dma/ioat/prep.c:714:1: warning: the frame size of 1048 bytes is larger than 1024 bytes [-Wframe-larger-than=]
}
gcc version 5.3.1 20151219 (Ubuntu 5.3.1-4ubuntu1)
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Nicholas Mc Guire <der.herr@hofr.at>
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Debugging ALSA hangups it was found that EP9302 (latest E2 rev.) DMA controller
sometimes asserts STALL interrupt instead of NFB interrupt. Simply ignoring the
difference and simply acting upon the amount of data we still have to transfer
seems to work fine. This somehow sounds similar to M2M issue which is already
dealt with in the driver, when the controller asserts DONE interrupt too early.
The issue is not documented in Cirrus Logic erratas for EP93XX, but original
Cirrus DMA driver from 2003 (not based on DMA API) did the similar handling
of STALL interrupt. In-tree driver (6d831c65) did it also, before conversion to
DMA engine API.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The offset of SINC should be 9, not 7, here fix this
typo.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Few fixes on drivers have piled up and one missed rcar bindings patch
which got somehow lost in for-linus branch so cherry-picked that one
Fixes are on dw, at_hdmac, edma
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWn3/rAAoJEHwUBw8lI4NHfFEP/3YTyj1BganEuV//h81l16Nl
fbgFtvgAZ5rilakOmsQJZ1Pp1r3aGgT8nULaBU/qtD2Ye0Ox0lQol/KfpnUDWH1a
go6yYnsArUJxs35QPCDV6WUnopzlDTLnamE7C/VcjQsLokJBEv4PubFKhQd6IFvB
mx8N0Rnn3oyhcAMADtUDnPljBgyPo1dwXbwM5IxlYI9Ar8zsT4hLMCHxXad7SzRR
SvRXMRflDlIxKwKh1f/4FnQ9BTW2mKb3nypBG6Uz8YatIPHliJO8LVjmvYsGA2KU
JtjDIpsRCeqETEPKlTSt6nQKdghR2CapDNEIS7Cv4LZFvCL3ADJL17xAfMKaxdkO
m4aVpK6vR+h/e0csYE0GYkcPugXAvm89MWHDkywmqo4CtCgh7QbMYxXR4MNsy3xS
TGHU2BkULrKoZkcKDKkXEB6fvfsMtzdd33/P0KPf2i0WcZUDo1jmETDLpz1Vehf6
hcRHURYMqHG/zJLItwQsAcJgfQtp+3oeiBv+N3FRjY/ECFPQWShFM5kVqac0Jr9y
e8gnC1+p7IfOesaHO/FUW5KvvWnQ1gskUFbtM0cZNGGqhiKTjx8lnWnXH530SU9D
Nf/bgNsQMoD3h5Uqsrsf5X6e+CNIGSqit9tONSqHSHG8POVCNo8CAkfj/sc7Ck+s
LH8N8eM3UIKsTojVbjMn
=16UM
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fix-4.5-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"Here is my second pull request for this window:
A few driver fixes have piled up and one missed rcar bindings patch
which got somehow lost in for-linus branch so cherry-picked that one.
Fixes are for dw, at_hdmac, edma"
* tag 'dmaengine-fix-4.5-rc1' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: rcar-dmac: Document SoC specific bindings
dmaengine: at_xdmac: fix resume for cyclic transfers
dmaengine: dw: fix cyclic transfer callbacks
dmaengine: dw: fix cyclic transfer setup
dmaengine: edma: Fix paRAM slot allocation for entry channel 0
When having cyclic transfers, the channel was paused when performing
suspend but was not correctly resumed.
Signed-off-by: Songjun Wu <songjun.wu@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: e1f7c9eee7 ("dmaengine: at_xdmac: creation of the atmel
eXtended DMA Controller driver")
Cc: <stable@vger.kernel.org> # 4.1 and later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We've had quite busy weeks in this cycle. Looking at ALSA core, the
significant changes are a few fixes wrt timer and sequencer ioctls
that have been revealed by fuzzer recently. Other than that, ASoC
core got a few updates about DAI link handling, but these are rather
straightforward refactoring.
In drivers scene, ASoC received quite lots of new drivers in addition
to bunch of updates for still ongoing Intel Skylake support and
topology API. HD-audio gained a new HDMI/DP hotplug notification via
component. FireWire got a pile of code refactoring/updates with
SCS.1x driver integration.
More highlights are shown below.
[NOTE: this contains also many commits for DRM. This is due to the
pull of drm stable branch into sound tree, as the base of i915 audio
component work for HD-audio. The highlights below don't contain
these DRM changes, as these are supposed to be pulled via drm tree in
anyway sooner or later.]
Core
- Handful fixes to harden ALSA timer and sequencer ioctls against
races reported by syzkaller fuzzer
- Irq description string can be unique to each card; only for
HD-audio for now
ASoC
- Conversion of the array of DAI links to a list for supporting
dynamically adding and removing DAI links
- Topology API enhancements to make everything more component based
and being able to specify PCM links via topology
- Some more fixes for the topology code, though it is still not final
and ready for enabling in production; we really need to get to the
point where that can be done
- A pile of changes for Intel SkyLake drivers which hopefully deliver
some useful initial functionality for systems with this chipset,
though there is more work still to come
- Lots of new features and cleanups for the Renesas drivers
- ANC support for WM5110
- New drivers: Imagination Technologies IPs, Atmel class D speaker,
Cirrus CS47L24 and WM1831, Dialog DA7128, Realtek RT5659 and
RT56156, Rockchip RK3036, TI PC3168A, and AMD ACP
- Rename PCM1792a driver to be generic pcm179x
HD-Audio
- Use audio component for i915 HDMI/DP hotplug handling
- On-demand binding with i915 driver
- bdl_pos_adj parameter adjustment for Baytrail controllers
- Enable power_save_node for CX20722; this shouldn't lead to
regression, hopefully
- Kabylake HDMI/DP codec support
- Quirks for Lenovo E50-80, Dell Latitude E-series, and other Dell
machines
- A few code refactoring
FireWire
- Lots of code cleanup and refactoring
- Integrate the support of SCS.1x devices into snd-oxfw driver;
snd-scs1x driver is obsoleted
USB-audio
- Fix possible NULL dereference at disconnection
- A regression fix for Native Instruments devices
Misc
- A few code cleanups of fm801 driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Gvgb
-----END PGP SIGNATURE-----
Merge tag 'sound-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"We've had quite busy weeks in this cycle. Looking at ALSA core, the
significant changes are a few fixes wrt timer and sequencer ioctls
that have been revealed by fuzzer recently. Other than that, ASoC
core got a few updates about DAI link handling, but these are rather
straightforward refactoring.
In drivers scene, ASoC received quite lots of new drivers in addition
to bunch of updates for still ongoing Intel Skylake support and
topology API. HD-audio gained a new HDMI/DP hotplug notification via
component. FireWire got a pile of code refactoring/updates with
SCS.1x driver integration.
More highlights are shown below.
[ NOTE: this contains also many commits for DRM. This is due to the
pull of drm stable branch into sound tree, as the base of i915 audio
component work for HD-audio. The highlights below don't contain
these DRM changes, as these are supposed to be pulled via drm tree
in anyway sooner or later. ]
Core:
- Handful fixes to harden ALSA timer and sequencer ioctls against
races reported by syzkaller fuzzer
- Irq description string can be unique to each card; only for
HD-audio for now
ASoC:
- Conversion of the array of DAI links to a list for supporting
dynamically adding and removing DAI links
- Topology API enhancements to make everything more component based
and being able to specify PCM links via topology
- Some more fixes for the topology code, though it is still not final
and ready for enabling in production; we really need to get to the
point where that can be done
- A pile of changes for Intel SkyLake drivers which hopefully deliver
some useful initial functionality for systems with this chipset,
though there is more work still to come
- Lots of new features and cleanups for the Renesas drivers
- ANC support for WM5110
- New drivers: Imagination Technologies IPs, Atmel class D speaker,
Cirrus CS47L24 and WM1831, Dialog DA7128, Realtek RT5659 and
RT56156, Rockchip RK3036, TI PC3168A, and AMD ACP
- Rename PCM1792a driver to be generic pcm179x
HD-Audio:
- Use audio component for i915 HDMI/DP hotplug handling
- On-demand binding with i915 driver
- bdl_pos_adj parameter adjustment for Baytrail controllers
- Enable power_save_node for CX20722; this shouldn't lead to
regression, hopefully
- Kabylake HDMI/DP codec support
- Quirks for Lenovo E50-80, Dell Latitude E-series, and other Dell
machines
- A few code refactoring
FireWire:
- Lots of code cleanup and refactoring
- Integrate the support of SCS.1x devices into snd-oxfw driver;
snd-scs1x driver is obsoleted
USB-audio:
- Fix possible NULL dereference at disconnection
- A regression fix for Native Instruments devices
Misc:
- A few code cleanups of fm801 driver"
* tag 'sound-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (722 commits)
ALSA: timer: Code cleanup
ALSA: timer: Harden slave timer list handling
ALSA: hda - Add fixup for Dell Latitidue E6540
ALSA: timer: Fix race among timer ioctls
ALSA: hda - add codec support for Kabylake display audio codec
ALSA: timer: Fix double unlink of active_list
ALSA: usb-audio: Fix mixer ctl regression of Native Instrument devices
ALSA: hda - fix the headset mic detection problem for a Dell laptop
ALSA: hda - Fix white noise on Dell Latitude E5550
ALSA: hda_intel: add card number to irq description
ALSA: seq: Fix race at timer setup and close
ALSA: seq: Fix missing NULL check at remove_events ioctl
ALSA: usb-audio: Avoid calling usb_autopm_put_interface() at disconnect
ASoC: hdac_hdmi: remove unused hdac_hdmi_query_pin_connlist
ASoC: AMD: Add missing include file
ALSA: hda - Fixup inverted internal mic for Lenovo E50-80
ALSA: usb: Add native DSD support for Oppo HA-1
ASoC: Make aux_dev more like a generic component
ASoC: bcm2835: cleanup includes by ordering them alphabetically
ASoC: AMD: Manage ACP 2.x SRAM banks power
...
Cyclic transfer callbacks rely on block completion interrupts which were
disabled in commit ff7b05f29f ("dmaengine/dw_dmac: Don't handle block
interrupts"). This re-enables block interrupts so the cyclic callbacks
can work. Other transfer types are not affected as they set the INT_EN
bit only on the last block.
Fixes: ff7b05f29f ("dmaengine/dw_dmac: Don't handle block interrupts")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Cc: <stable@vger.kernel.org>
Commit 61e183f830 ("dmaengine/dw_dmac: Reconfigure interrupt and
chan_cfg register on resume") moved some channel initialisation to
a new function which must be called before starting a transfer.
This updates dw_dma_cyclic_start() to use dwc_dostart() like the other
modes, thus ensuring dwc_initialize() gets called and removing some code
duplication.
Fixes: 61e183f830 ("dmaengine/dw_dmac: Reconfigure interrupt and chan_cfg register on resume")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Cc: <stable@vger.kernel.org>
This round we have few new features, new driver and updates to few drivers.
The new features to dmaengine core are:
- Synchronized transfer termination API to terminate the dmaengine
transfers in synchronized and async fashion as required by users.
We have its user now in ALSA dmaengine lib, img, at_xdma, axi_dmac
drivers.
- Universal API for channel request and start consolidation of request
flows. It's user is ompa-dma driver.
- Introduce reuse of descriptors and use in pxa_dma driver
Add/Remove:
- STM32 DMA driver
- Removal of unused R-Car HPB-DMAC driver
Updates:
- ti-dma-crossbar updates for supporting eDMA
- tegra-apb pm updates
- idma64
- mv_xor updates
- ste_dma updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=D5Fb
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.5-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This round we have few new features, new driver and updates to few
drivers.
The new features to dmaengine core are:
- Synchronized transfer termination API to terminate the dmaengine
transfers in synchronized and async fashion as required by users.
We have its user now in ALSA dmaengine lib, img, at_xdma, axi_dmac
drivers.
- Universal API for channel request and start consolidation of
request flows. It's user is ompa-dma driver.
- Introduce reuse of descriptors and use in pxa_dma driver
Add/Remove:
- New STM32 DMA driver
- Removal of unused R-Car HPB-DMAC driver
Updates:
- ti-dma-crossbar updates for supporting eDMA
- tegra-apb pm updates
- idma64
- mv_xor updates
- ste_dma updates"
* tag 'dmaengine-4.5-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (54 commits)
dmaengine: mv_xor: add suspend/resume support
dmaengine: mv_xor: de-duplicate mv_chan_set_mode*()
dmaengine: mv_xor: remove mv_xor_chan->current_type field
dmaengine: omap-dma: Add support for DMA filter mapping to slave devices
dmaengine: edma: Add support for DMA filter mapping to slave devices
dmaengine: core: Introduce new, universal API to request a channel
dmaengine: core: Move and merge the code paths using private_candidate
dmaengine: core: Skip mask matching when it is not provided to private_candidate
dmaengine: mdc: Correct terminate_all handling
dmaengine: edma: Add probe callback to edma_tptc_driver
dmaengine: dw: fix potential memory leak in dw_dma_parse_dt()
dmaengine: stm32-dma: Fix unchecked deference of chan->desc
dmaengine: sh: Remove unused R-Car HPB-DMAC driver
dmaengine: usb-dmac: Document SoC specific compatibility strings
ste_dma40: Delete an unnecessary variable initialisation in d40_probe()
ste_dma40: Delete another unnecessary check in d40_probe()
ste_dma40: Delete an unnecessary check before the function call "kmem_cache_destroy"
dmaengine: tegra-apb: Free interrupts before killing tasklets
dmaengine: tegra-apb: Update driver to use GFP_NOWAIT
dmaengine: tegra-apb: Only save channel state for those in use
...
edma_alloc_slot was not checking the channel mapping support existence when
slot 0 has been requested (used as entry slot for channel/event 0).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
* acpi-soc:
PM / clk: don't leave clocks enabled when driver not bound
i2c: dw: Add APM X-Gene ACPI I2C device support
ACPI / APD: Add APM X-Gene ACPI I2C device support
ACPI / LPSS: change 'does not have' to 'has' in comment
Revert "dmaengine: dw: platform: provide platform data for Intel"
dmaengine: dw: return immediately from IRQ when DMA isn't in use
dmaengine: dw: platform: power on device on shutdown
ACPI / LPSS: override power state for LPSS DMA device
ACPI / LPSS: power on when probe() and otherwise when remove()
ACPI / LPSS: do delay for all LPSS devices when D3->D0
ACPI / LPSS: allow to use specific PM domain during ->probe()
Revert "ACPI / LPSS: allow to use specific PM domain during ->probe()"
device core: add BUS_NOTIFY_DRIVER_NOT_BOUND notification
x86/platform/iosf_mbi: Remove duplicate definitions
Conflicts:
drivers/i2c/busses/i2c-designware-platdrv.c
Since we have a work around to prevent a system hangup we don't need to provide
a platform data explicitly anymore.
This reverts commit 175267b389.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is no need to bother the hardware when all channels are idle. We have not
to get any interrupts.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We have to call dw_dma_disable() to stop any ongoing transfer. On some
platforms we can't do that since DMA device is powered off. Moreover we have no
possibility at that point to check if the platform is affected or not. That's
why we call pm_runtime_get_sync() / pm_runtime_put() unconditionally. On the
other hand we can't use pm_runtime_suspended() because runtime PM framework is
not fully used by the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For interrupt controller that doesn't support irq_disable and hardware
with level interrupt, an extra interrupt can be pending. This patch fixes
the issue by setting IRQ_DISABLE_UNLAZY flag for the interrupt line.
Reference: http://git.kernel.org/tip/e9849777d0e27cdd2902805be51da73e7c79578c
Signed-off-by: Rameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This commit adds suspend/resume support to the mv_xor driver. The
config and interrupt mask registers must be saved and restored, and
upon resume, the MBus windows configuration must also be done again.
Tested on Armada 388 GP, with a RAID 5 array, accessed before and
after a suspend to RAM cycle.
Based on work from Ofer Heifetz and Lior Amsalem.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When commit 6f166312c6 ("dmaengine: mv_xor: add support for a38x
command in descriptor mode") added support for the descriptor mode
available in Marvell Armada 38x and later SoCs, it added a new
function mv_chan_set_mode_to_desc() which allows to configure a XOR
channel to get the specific operation to be done from each individual
DMA descriptor.
However, this function was mainly a duplicate of the existing
mv_chan_set_mode(), with just the operation being different.
This commit re-organizes the code into a single mv_chan_set_mode()
function, which takes the operation mode as argument, and the
mv_xor_channel_add() function decides whether to use
XOR_OPERATION_MODE_IN_DESC or XOR_OPERATION_MODE_XOR.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since commit 3e4f52e2da ("dma: mv_xor: Simplify the DMA_MEMCPY
operation"), this field is no longer used, so get rid of it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This reverts commit e958e079e2 ("dmaengine: mic_x100: add missing
spin_unlock").
The above patch is incorrect. There is nothing wrong with the original
code. The spin_lock is acquired in the "prep" functions and released
in "submit".
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add support for providing device to filter_fn mapping so client drivers
can switch to use the dma_request_chan() API.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add support for providing device to filter_fn mapping so client drivers
can switch to use the dma_request_chan() API.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The two API function can cover most, if not all current APIs used to
request a channel. With minimal effort dmaengine drivers, platforms and
dmaengine user drivers can be converted to use the two function.
struct dma_chan *dma_request_chan_by_mask(const dma_cap_mask_t *mask);
To request any channel matching with the requested capabilities, can be
used to request channel for memcpy, memset, xor, etc where no hardware
synchronization is needed.
struct dma_chan *dma_request_chan(struct device *dev, const char *name);
To request a slave channel. The dma_request_chan() will try to find the
channel via DT, ACPI or in case if the kernel booted in non DT/ACPI mode
it will use a filter lookup table and retrieves the needed information from
the dma_slave_map provided by the DMA drivers.
This legacy mode needs changes in platform code, in dmaengine drivers and
finally the dmaengine user drivers can be converted:
For each dmaengine driver an array of DMA device, slave and the parameter
for the filter function needs to be added:
static const struct dma_slave_map da830_edma_map[] = {
{ "davinci-mcasp.0", "rx", EDMA_FILTER_PARAM(0, 0) },
{ "davinci-mcasp.0", "tx", EDMA_FILTER_PARAM(0, 1) },
{ "davinci-mcasp.1", "rx", EDMA_FILTER_PARAM(0, 2) },
{ "davinci-mcasp.1", "tx", EDMA_FILTER_PARAM(0, 3) },
{ "davinci-mcasp.2", "rx", EDMA_FILTER_PARAM(0, 4) },
{ "davinci-mcasp.2", "tx", EDMA_FILTER_PARAM(0, 5) },
{ "spi_davinci.0", "rx", EDMA_FILTER_PARAM(0, 14) },
{ "spi_davinci.0", "tx", EDMA_FILTER_PARAM(0, 15) },
{ "da830-mmc.0", "rx", EDMA_FILTER_PARAM(0, 16) },
{ "da830-mmc.0", "tx", EDMA_FILTER_PARAM(0, 17) },
{ "spi_davinci.1", "rx", EDMA_FILTER_PARAM(0, 18) },
{ "spi_davinci.1", "tx", EDMA_FILTER_PARAM(0, 19) },
};
This information is going to be needed by the dmaengine driver, so
modification to the platform_data is needed, and the driver map should be
added to the pdata of the DMA driver:
da8xx_edma0_pdata.slave_map = da830_edma_map;
da8xx_edma0_pdata.slavecnt = ARRAY_SIZE(da830_edma_map);
The DMA driver then needs to configure the needed device -> filter_fn
mapping before it registers with dma_async_device_register() :
ecc->dma_slave.filter_map.map = info->slave_map;
ecc->dma_slave.filter_map.mapcnt = info->slavecnt;
ecc->dma_slave.filter_map.fn = edma_filter_fn;
When neither DT or ACPI lookup is available the dma_request_chan() will
try to match the requester's device name with the filter_map's list of
device names, when a match found it will use the information from the
dma_slave_map to get the channel with the dma_get_channel() internal
function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Channel matching with private_candidate() is used in two paths, the error
checking is slightly different in them and they are duplicating code also.
Move the code under find_candidate() to provide consistent execution and
going to allow us to reuse this mode of channel lookup later.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If mask is NULL skip the mask matching against the DMA device capabilities.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use of the CANCEL bit in mdc_terminate_all creates an
additional 'command done' to appear in the registers (in
addition to an interrupt).
In addition, there is a potential race between
mdc_terminate_all and the irq handler if a transfer
completes at the same time as the terminate all (presently
this results in an inappropriate warning).
To handle these issues, any outstanding 'command done'
events are cleared during mdc_terminate_all and the irq
handler takes no action when there are no new 'command done'
events.
Signed-off-by: Damien.Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Due to changes in device and platform code drivers w/o probe will fail to
load. This means that the devices for eDMA TPTCs are goign to be without
driver and omap hwmod code will turn them off after the kernel finished
loading:
[ 3.015900] platform 49800000.tptc: omap_device_late_idle: enabled but no driver. Idling
[ 3.024671] platform 49a00000.tptc: omap_device_late_idle: enabled but no driver. Idling
This will prevent eDMA to work since the TPTCs are not enabled.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Fixes: 34635b1acc ("dmaengine: edma: Add dummy driver skeleton for edma3-tptc")
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If the "dma-channels" DT property is missing, the dw_dma_parse_dt()
function return NULL, but not before allocating memory for a struct
dw_dma_platform_data through devres. If the device supports parameter
detection, the probe still succeeds and the allocated memory is not
released until the device is removed.
Fix this by deferring the allocation until after checking the
"dma-channels" property.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes at_xdmac_prep_dma_memcpy(). Indeed the data width field
of the Channel Configuration register was not updated properly in the
loop: the bits of the dwidth field were not cleared before adding their
new value.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: e1f7c9eee7 ("dmaengine: at_xdmac: creation of the atmel eXtended DMA Controller driver")
Cc: stable@vger.kernel.org #4.1 and later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
'commit d8b468394f ("dmaengine: Add STM32 DMA driver")' leads to the
following Smatch complaint:
drivers/dma/stm32-dma.c:562 stm32_dma_issue_pending()
error: we previously assumed 'chan->desc' could be null (see line 560)
So, this patch fixes the unchecked dereference of chan->desc by returning
operation not permitted error when stm32_dma_start_transfer() does not
succeed to allocate a virtual channel descriptor.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As of commit 4baadb9e05 ("ARM: shmobile: r8a7778: remove obsolete
setup code"), the Renesas R-Car HPB-DMAC driver is no longer used.
In theory it could still be used on R-Car Gen1 SoCs, but that requires
adding DT support to the driver, which is not planned.
Remove the driver, it can be resurrected from git history when needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The variable "res" will eventually be set to a resource pointer from
a call of the d40_hw_detect_init(() function.
Thus let us omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
A single jump label was used by the d40_probe() function in several cases
for error handling which was a bit inefficient here.
* This implementation detail could be improved by the introduction
of another jump label.
* Remove an extra check for the variable "base".
* Omit its explicit initialisation at the beginning then.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The kmem_cache_destroy() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This change makes the DT file to be easier to read since the reserved slots
array does not need the '/bits/ 16' to be specified, which might confuse
some people.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This change makes the DT file to be easier to read since the memcpy
channels array does not need the '/bits/ 16' to be specified, which might
confuse some people.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
On probe failure or driver removal, before killing any tasklets, ensure
that the channel interrupt is freed to ensure that another channel
interrupt cannot occur and schedule the tasklet again.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The tegra20-apb-dma driver currently uses the flag GFP_ATOMIC when
allocating memory for structures used in conjunction with the DMA
descriptors. It is preferred that dmaengine drivers use GFP_NOWAIT
instead and so the emergency memory pool will not be used by these
drivers.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently the tegra-apb DMA driver suspend/resume helpers, save and
restore the registers for all channels regardless of whether they are
in use or not. Change this so that only channels that have been
allocated and configured are saved and restored.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Newer tegra devices have a separate word count register per channel that
contains the number of words to be transferred. This register is not
saved or restored by the suspend/resume helpers for these newer devices
and so ensure that it is.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In the tegra_dma_runtime_suspend/resume functions, the pdev structure
is not needed, and so just call dev_get_drvdata() to get the device
data structure.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The tegra-apb DMA driver enables runtime-pm but never calls
pm_runtime_get/put and hence the runtime-pm callbacks are never invoked.
The driver manages the clocks by directly calling clk_prepare_enable()
and clk_unprepare_disable().
Fix this by replacing the clk_prepare_enable() and clk_disable_unprepare()
with pm_runtime_get_sync() and pm_runtime_put(), respectively. Note that
the consequence of this is that if runtime-pm is disabled, then the clocks
will remain on the entire time the driver is loaded. However, if
runtime-pm is disabled, then power is not most likely not a concern.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
spin lock should be released while returning from function
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Calling synchronize_irq() right before devm_free_irq() is quite useless. On
one hand the IRQ can easily fire again before devm_free_irq() is entered,
on the other hand devm_free_irq() itself calls synchronize_irq() internally
(in a race condition free way), before any state associated with the IRQ is
freed.
Patch was generated using the following semantic patch:
// <smpl>
@@
expression irq, dev;
@@
-synchronize_irq(irq);
devm_free_irq(dev, irq, ...);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Calling synchronize_irq() right before free_irq() is quite useless. On one
hand the IRQ can easily fire again before free_irq() is entered, on the
other hand free_irq() itself calls synchronize_irq() internally (in a race
condition free way), before any state associated with the IRQ is freed.
Patch was generated using the following semantic patch:
// <smpl>
@@
expression irq;
@@
-synchronize_irq(irq);
free_irq(irq, ...);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This add power management suspend/resume support for the fsl-edma
driver.
eDMA acted as a basic function used by others. What it needs to do
is the two steps below to support power management.
In fsl_edma_suspend_late:
Check whether the DMA chan is idle, if it is not idle disable DMA
request.
In fsl_edma_resume_early:
Enable the eDMA and wait for being used.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
f931782917 dmaengine: bcm2835-dma: Fix memory leak when stopping a
running transfer
Fixed the memleak, but introduced another issue: the terminate_all callback
might be called with interrupts disabled and the dma_free_coherent() is
not allowed to be called when IRQs are disabled.
Convert the driver to use dma_pool_* for managing the list of control
blocks for the transfer.
Fixes: f931782917 ("dmaengine: bcm2835-dma: Fix memory leak when stopping a running transfer")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When performing interleaved transfers with numf > 1, an extra line is
copied. The mbr.bc field is incremented once too often. The length of
the block is (BLEN+1) microblocks.
Signed-off-by: Sylvain ETIENNE <Sylvain.ETIENNE@ingenico.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: 4e5385784e ("dmaengine: at_xdmac: handle numf > 1")
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The code was not in agreement with the comments.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable@vger.kernel.org # 4.3 and later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is no need to calculate an overall length of the descriptor each time we
call for DMA transfer status. Instead we do this at descriptor allocation stage
and keep the stored length for further usage.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently the match DMA controller is done only for lower 32 bits of
address which might be not true on 64-bit platform. Check upper portion
as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since a local variable contains the number of hardware desriptors at the
beginning of idma64_desc_fill() we may use it to index the last descriptor as
well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Explicitly show in idma64_desc_fill() how we link the hardware
descriptors.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This tells, for example, IOMMU what the maximum size of a segment
the DMA controller can send.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is no need to disable interrupts in the IRQ handler. The driver
guarantess that at one time only one descriptor is active, besides the fact
that each call to the same channel will be serialized in idma64_chan_irq()
handler anyway.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Fix typo in a macro which was not used until now. It explains why there
is no error at compilation time.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: e1f7c9eee7 "dmaengine: at_xdmac: creation of the atmel eXtended
DMA Controller driver"
Cc: stable@vger.kernel.org # 3.19 and later
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When setting the channel configuration register, the perid field is not
set to 0 since it is useless for mem2mem transfers. Unfortunately, a
device has 0 as perid. It could cause spurious flags status because
the controller could mix some events from the two channels.
For that reason, use the highest perid value for mem2mem transfers since it
doesn't match the perid of other devices.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes an issue that list_for_each_entry() in
usb_dmac_chan_terminate_all() is possible to cause endless loop because
this will move own desc to the desc_freed. So, this driver should use
list_for_each_entry_safe() instead of list_for_each_entry().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When a DMA client driver decides that it is not providing callback for
completion of a transfer (and/or does not set the DMA_PREP_INTERRUPT) but
it will poll the status of the transfer (in case of short memcpy for
example) we will not get interrupt for the completion of the transfer and
will not mark the transaction as done.
Check the channel enable bit in the CCR when the status is queried and if
the channel is no longer active, we call the omap_dma_callback() to handle
the transfer completion.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The use of tasklet to actually start the DMA transfer slightly decreases the
DMA throughput since it adds small scheduling delay when the transfer is
started. In normal use, even with high I/O load the tasklet would start
one transaction at a time, however running the DMAtest for memcpy on all
available channels will cause the tasklet to start about 15 transfers.
The performance numbers on OMAP4 PandaBoard-es (test_buf_size = 6553):
With the tasklet:
dmatest: dma0chan30-copy: summary 5000 tests, 0 failures 186 iops 593 KB/s (0)
dmatest: dma0chan8-copy0: summary 5000 tests, 0 failures 184 iops 584 KB/s (0)
dmatest: dma0chan13-copy: summary 5000 tests, 0 failures 184 iops 585 KB/s (0)
dmatest: dma0chan12-copy: summary 5000 tests, 0 failures 184 iops 585 KB/s (0)
dmatest: dma0chan7-copy0: summary 5000 tests, 0 failures 183 iops 581 KB/s (0)
With this patch (no tasklet):
dmatest: dma0chan4-copy0: summary 5000 tests, 0 failures 199 iops 644 KB/s (0)
dmatest: dma0chan5-copy0: summary 5000 tests, 0 failures 199 iops 645 KB/s (0)
dmatest: dma0chan6-copy0: summary 5000 tests, 0 failures 199 iops 637 KB/s (0)
dmatest: dma0chan24-copy: summary 5000 tests, 0 failures 199 iops 638 KB/s (0)
dmatest: dma0chan16-copy: summary 5000 tests, 0 failures 199 iops 638 KB/s (0)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The for_each_sg() macro's last parameter is inteded to be used as counter.
We can use 'i' instead of 'j' within the loop for indexes.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
During mem copy both src and dst position moves at the same pace. Check the
dst position for progress reporting.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In eDMA the events are directly mapped to a DMA channel (for example DMA
event 14 can only be handled by DMA channel 14). If the memcpy is enabled
on the eDMA, there is a possibility that the crossbar driver would assign
DMA event number already allocated in eDMA for memcpy. Furthermore the
eDMA can be shared with DSP in which case the crossbar driver should also
avoid mapping xbar events to DSP used event numbers (or channels).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The use of idr was nice, but it was a bit heavy and we did not need the
features it provides. Using simple bitmap to track allocated DMA channels
is adequate here and it will be easier to add support for reserving
channels later on.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Allow the crossbar driver to be used with the eDMA node with non legacy
binding.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As we are now passing the filter data as pointers to the drivers,
we can take the final step and also pass the filter function the
same way. I'm keeping this change separate, as there it's less
obvious that this is a net win.
Upsides of this are:
- The ASoC drivers are completely independent from the DMA engine
implementation, which simplifies the Kconfig logic and in theory
allows the same sound drivers to be built in a kernel that supports
different kinds of dmaengine drivers.
- Consistency with other subsystems and drivers
On the other hand, we have a few downsides:
- The s3c24xx-dma driver now needs to be built-in for the ac97 platform
device to be instantiated on s3c2440.
- samsung_dmaengine_pcm_config cannot be marked 'const' any more
because the filter function pointer needs to be set at runtime.
This is safe as long we don't have multiple different DMA engines
in thet same system at runtime, but is nonetheless ugly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dca_ops structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dma_addr_t may be defined as 32 or 64 bit depending on configuration,
so it cannot be printed using the normal format strings, as
gcc correctly warns:
drivers/dma/at_hdmac.c: In function 'atc_prep_dma_interleaved':
drivers/dma/at_hdmac.c:731:28: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'dma_addr_t {aka long long unsigned int}' [-Wformat=]
This changes the format strings to use the special "%pad" format
string that prints a dma_addr_t, and changes the arguments so we
pass the address by reference as required.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dma_addr_t may be defined as 32 or 64 bit depending on configuration,
so it cannot be printed using the normal format strings, as
gcc correctly warns:
drivers/dma/at_xdmac.c: In function 'at_xdmac_interleaved_queue_desc':
drivers/dma/at_xdmac.c:922:51: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t {aka long long unsigned int}' [-Wformat=]
This changes the format strings to use the special "%pad" format
string that prints a dma_addr_t, and changes the arguments so we
pass the address by reference as required.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The sdma_probe function will call sdma_event_remap, but sdma_event_remap
marked with the __init annotation which make the kbuild complains as the
following log:
WARNING: drivers/dma/built-in.o(.text+0x56fc): Section mismatch in reference
from the function sdma_probe() to the function .init.text:sdma_event_remap()
The function sdma_probe() references
the function __init sdma_event_remap().
This is often because sdma_probe lacks a __init
annotation or the annotation of sdma_event_remap is wrong.
Remove the __init annotation on sdma_event_remap to kill this build warning
Signed-off-by: Jason Liu <r64343@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Andy Shevchenko