io_cmpl_skip keep track of number of completions to skip when stats are
reset. If a fw_reset happens immediately after stats reset it could put
it out of sync so need to reset io_cmpl_skip when fw reset is completed.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Do not call the stock libfc terminate rport i/o handler so we won't reset
the libfc exchange manager and kill any outstanding discovery requests.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In eh_abort, driver is calling scsi->done() for a IO for which cleanup is
pending. As the IO is outstanding with the firmware, it may do DMA
associated with the IO. This may lead to heap corruption.
Do not complete the IO for which cleanup is still pending. Return failure
from eh_abort and let the SCSI-ml retry the IO.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some vports addresses stored in NVRAM may have zero for the WWNN. Adjust
the WWNN that we'll use to be the same as the WWPN.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the connection is not offloaded then the backpointers from the tgt
pointer are undefined.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add the following filters to bnx2fc_recv_frame():
1. Filter out invalid packets
- eth->dest_mac[3] matches FC frame's D_ID
2. Filter out packets that are not from our connected target
- In FIP_ST_ENABLED mode
- eth->src_mac matches fcoe_ctlr->dest_addr
3. Filter out packets where if d_id of the packet doesn't belong to
the device when one is already assigned a port_id, only then this
packet is dropped
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove the SCSI_MQ_DEFAULT config option and default to the blk-mq I/O
path now that we had plenty of testing, and have I/O schedulers for
blk-mq. The module option to disable the blk-mq path is kept around for
now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
libsas uses scsi_queue_work() to queue its internal event notifications.
scsi_queue_work() can return -EINVAL if the work queue doesn't exist and
it does call queue_work() which can return false if the work is already
queued.
Make the SAS event code capable of returning errors up to the caller,
which is handy when changing to dynamically allocated work in libsas
as well, as discussed here: https://lkml.org/lkml/2017/6/14/121.
[mkp: fixed typo]
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds switch command support for FC-4 type of FC-NVMe (0x28)
for resgistering HBA port to the management server. RFT_ID command is
used to register FC-4 type of 0x28 and RFF_ID is used to register FC-4
features bits for FC-NVMe port.
Signed-off-by: Darren Trapp <darren.trapp@cavium.com>
Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Anil Gurumurthy <anil.gurumurhty@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-By: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This code provides the interfaces to register remote and local ports of
FC4 type 0x28 with the FC-NVMe transport and transports the requests
(FC-NVMe FC link services and FC-NVMe commands IUs) to the fabric. It
also provides the support for allocating h/w queues and aborting FC-NVMe
FC requests.
Signed-off-by: Darren Trapp <darren.trapp@cavium.com>
Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Anil Gurumurthy <anil.gurumurhty@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds logic to handle the completion of FC-NVMe commands and
creates a sub-command in the SRB command structure to manage NVMe
commands.
Signed-off-by: Darren Trapp <darren.trapp@cavium.com>
Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Anil Gurumurthy <anil.gurumurhty@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added logic to change the login process into an optional PRIL step for
FC-NVMe ports as a separate operation, such that we can change type to
0x28 (NVMe).
Currently, the driver performs the PLOGI/PRLI together as one operation,
but if the discovered port is an NVMe port then we first issue the PLOGI
and then we issue the PRLI. Also, the fabric discovery logic was changed
to mark each discovered FC NVMe port, so that we can register them with
the FC-NVMe transport later.
Signed-off-by: Darren Trapp <darren.trapp@cavium.com>
Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Anil Gurumurthy <anil.gurumurhty@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
These fields only hold one set of value. Replace it with macros to
reduce cache thrash.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
By default this flag is forced to true. Remove this flag and
unneccessary check for this flag.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For target main path io routines that uses qpair, create new logging &
debugging routines to use qpair instead of reaching for scsi_qla_host to
reduce cache thrash.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add call back to door bell for qpair. This help reduce access to
qla_hw_data structure, in order to reduce cach thrash.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For ISP27XX, use shadow register to read FW provided REQQ's consumer
index. The shadow register is dma'ed by firmware.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Move chip_reset, enable_class_2 fields from qla_hw_data to qla_qpair
to reduce cache thrash for target MQ.
- Optimizations to reduce unnecessary memory load for good path io.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add fw_started flag to qpair to reduce cache thrash. This reduce access
to qla_hw_data structure by each qpair.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For Target mode, user can control the work load by placing qla2xxx's irq
vector on certain CPU via the smp_affinity knob. This patch allows user
to control the number of QPair's irq to be active. The irqs are
allocated at driver load time until unload. The work itself is placed on
the QPair based on user setting.
Usage:
modprobe qla2xxx qlini_mode=disabled ql2xuctrlirq=1
mount -t debugfs none /sys/kernel/debug
echo 2 > /sys/kernel/debug/qla2xxx/qla2xxx_[host num]/naqp
echo [cpu id] > /proc/irq/[irq id]/smp_affinity_list
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In target mode driver, queue pairs are not created during driver load
time, instead they are created at the configuration time after chip
reset. If a user tries to load/unload driver after queue pairs are
created, then there would be mailbox failure, while deleting queue
pairs. Flag is added to check if queue pairs are created or not. Queue
pairs will be deleted only If they were created during target
configuration.
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enable Multi Queue for Target mode. At Initiator LUN scan time, each LUN
is assign to a QPair. Each QPair is affinitize to certain CPU. When new
cmd arrives from the wire, the lunid is used to search for qpair. The
qpair's affinitized cpuid will be used to queue up the work element.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In Current code, Req Q 0, RespQ 0 & hardware_lock are the main resources
for sending and process completion of Target IO. These resources are now
referenced behind a new qpair/"struct qla_qpair base_qpair". Main path
IO handle will access those resources via the qpair pointer in
preparation for Target MQ.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Merge active/outstanding cmd arrays from target side and initiator side
together in prepration for Target Multi Queue support.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, the SCSI command presented to the device reset handler is used
to send TMFs to the AFU for a device reset. This behavior is incorrect as
the command presented is an actual command and not a special notification.
As such, it should only be used for reference and not be acted upon.
Additionally, the existing TMF transmission routine does not account for
actual errors from the hardware, only reflecting failure when a timeout
occurs. This can lead to a condition where the device reset handler is
presented with a false 'success'.
Update send_tmf() to dynamically allocate a private command for sending
the TMF command and properly reflect failure when the completed command
indicates an error or was aborted. Detect TMF commands during response
processing and avoid scsi_done() for these types of commands. Lastly,
update comments in the TMF processing paths to describe the new behavior.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SCSI core now zeroes the per-command private data area prior to
calling into the LLD. Replace the clearing operation that takes place
when the private command data reference is obtained with a routine that
performs common initializations. The zeroing that takes place in the
device reset path remains intact as the private command data associated
with the specified SCSI command is not guaranteed to be cleared.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The cxlflash driver supports performing a write-same16 to scrub virtual
luns when they are released by a user. To date, AFUs for adapters that
are supported by cxlflash do not have the capability to unmap as part of
the WS operation. This can lead to fragmented flash devices which results
in performance degradation.
Future AFUs can optionally support unmap write-same commands and reflects
this support via the context control register. This provides userspace
applications with direct visibility such that they need not depend on a
host API.
Detect unmap support during cxlflash initialization by reading the context
control register associated with the primary hardware queue. Update the
existing write_same16() routine to set the unmap bit in the CDB when unmap
is supported by the host.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Adopt the SISLite AFU debug capability to allow future CXL Flash
adapters the ability to better debug AFU issues. Update the SISLite
header with the changes necessary to support AFU debug operations
and create a host ioctl interface for user debug software. Also
update the cxlflash documentation to describe this new host ioctl.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Adopt the SISLite AFU LUN provisioning capability to allow future CXL
Flash adapters the ability to better manage storage. Update the SISLite
header with the changes necessary to support LUN provision operations
and create a host ioctl interface for user LUN management software. Also
update the cxlflash documentation to describe this new host ioctl.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The existing AFU capability checking infrastructure is closely tied to
the command mode capability bits. In order to support new capabilities,
refactor the existing infrastructure to be more generic.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As staging for supporting various host management functions, add a host
ioctl infrastructure to filter ioctl commands and perform operations that
are common for all host ioctls. Also update the cxlflash documentation to
create a new section for documenting host ioctls.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To date the only supported internal AFU command is AFU sync. The logic
to send an internal AFU command is embedded in the specific AFU sync
handler and would need to be duplicated for new internal AFU commands.
In order to support new internal AFU commands, separate code that is
common for AFU internal commands into a generic transmission routine
and support passing back command status through an IOASA structure.
The first user of this new routine is the existing AFU sync command.
As a cleanup, use a descriptive name for the AFU sync command instead
of a magic number.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The cxlflash driver currently lacks host management interface. Future
devices supported by cxlflash will provide a variety of host-wide
management functions. Examples include LUN provisioning, hardware debug
support, and firmware download.
In order to provide a way to manage the device, a character device will
be created during probe of each adapter. This device will support a set of
ioctls defined in the SISLite specification from which administrators can
manage the adapter.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To date, CXL flash devices do not support a single command abort operation.
Instead, the SISLite specification provides a context reset operation to
cleanup all pending commands for a given context.
When a context reset is successful, it is guaranteed that the AFU has
aborted all currently pending I/O. This sequence is less invasive than a
device or host reset and can be executed to support scsi command abort
requests. Add eh_abort_handler callback support to process command timeouts
and abort requests.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the AFU is reset in an error path, pending scsi commands can be
silently dropped without completion or a formal abort. This puts the onus
on the cxlflash driver to notify mid-layer and indicating that the command
can be retried.
Once the card has been quiesced, the hardware send queue lock is acquired
to prevent any data movement while the pending commands are processed.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, there is no book keeping of the pending scsi commands in the
cxlflash driver. This lack of tracking in-flight requests is too
restrictive and requires a heavy-hammer reset each time an adapter error is
encountered. Additionally, it does not allow for commands to be properly
retried.
In order to avoid this problem and to better handle error path command
cleanup, introduce a linked list for each hardware queue that tracks
pending commands.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
AFU sync operations are not currently evaluated for failure. This is
acceptable for paths where there is not a dependency on the AFU being
consistent with the host. Examples include link reset events and LUN
cleanup operations. On paths where there is a dependency, such as a LUN
open, a sync failure should be acted upon.
In the event of AFU sync failures, either log or cleanup as appropriate for
operations that are dependent on a successful sync completion.
Update documentation to reflect behavior in the event of an AFU sync
failure.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A context reset failure indicates the AFU is in a bad state. At present,
when such a situation occurs, no further action is taken. This leaves the
adapter in an unusable state with no recoverable actions.
To avoid this situation, context reset failures will be escalated to a host
reset operation. This will be done asynchronously to allow the acting
thread to return to the user with a failure.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Per the SISLite specification, context_reset() writes 0x1 to the LSB of the
reset register. When the AFU processes this reset request, it is expected
to clear the bit after reset is complete. The current implementation simply
checks that the entire value read back is not 1, instead of masking off the
LSB and evaluating it for a change to 0. Should the AFU manipulate other
bits during the reset (reading back a value of 0xF for example), successful
completion will be prematurely indicated given the existing logic.
Additionally, in the event that the context reset operation fails, there
does not currently exist a way to provide feedback to the initiator of the
reset. This poses a problem for the rare case that a context reset fails as
the caller will proceed on the assumption that all is well.
To remedy these issues, refactor the context reset routine to only mask off
the LSB when evaluating for success and return status to the caller. Also
update the context reset handler parameters to pass a hardware queue
reference instead of a single command to better reflect that the entire
queue associated with the context is impacted by the reset.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The cxlflash_afu_sync() routine returns a negative one to indicate any kind
of failure. This makes it impossible to establish why the error occurred.
Update the return codes to clearly indicate the failure cause to the
caller.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently there are separate spin locks for the two supported I/O queueing
models. This makes it difficult to serialize with paths outside the enqueue
path.
As a design simplification and to support serialization with enqueue
operations, move to only a single lock that is used for enqueueing
regardless of the queueing model.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use dma_alloc_attrs directly instead of the dma_alloc_noncoherent
wrapper.
[mkp: fixed driver name]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use dma_alloc_attrs directly instead of the dma_alloc_noncoherent
wrapper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Satish Kharat