On Thu, Aug 13, 2009 at 04:14:58PM +1000, Benjamin Herrenschmidt wrote:
> On Tue, 2009-08-11 at 11:39 +0200, Bastian Blank wrote:
> > This patch just disables this driver on SMP kernels, as it is obviously
> > not supported.
> Why not remove the #error instead ? :-) I don't think it's still
> meaningful, especially since we use the timebase for delays nowadays
> which doesn't depend on the CPU frequency...
Your call. Take this one:
The build of a PowerMac 32bit kernel currently fails with
error: #warning "WARNING, CPUFREQ not recommended on SMP kernels"
Thie patch removes the not longer applicable SMP warning from the
PowerMac cpufreq code.
Signed-off-by: Bastian Blank <waldi@debian.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The ptrace POKETEXT interface allows a process to modify the text pages of
a child process being ptraced, usually to insert breakpoints via trap
instructions. The kernel eventually calls copy_to_user_page, which in turn
calls __flush_icache_range to invalidate the icache lines for the child
process.
However, this function does not work on 44x due to the icache being virtually
indexed. This was noticed by a breakpoint being triggered after it had been
cleared by ltrace on a 440EPx board. The convenient solution is to do a
flash invalidate of the icache in the __flush_icache_range function.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is an attempt at cleaning up a bit the way we handle execute
permission on powerpc. _PAGE_HWEXEC is gone, _PAGE_EXEC is now only
defined by CPUs that can do something with it, and the myriad of
#ifdef's in the I$/D$ coherency code is reduced to 2 cases that
hopefully should cover everything.
The logic on BookE is a little bit different than what it was though
not by much. Since now, _PAGE_EXEC will be set by the generic code
for executable pages, we need to filter out if they are unclean and
recover it. However, I don't expect the code to be more bloated than
it already was in that area due to that change.
I could boast that this brings proper enforcing of per-page execute
permissions to all BookE and 40x but in fact, we've had that now for
some time as a side effect of my previous rework in that area (and
I didn't even know it :-) We would only enable execute permission if
the page was cache clean and we would only cache clean it if we took
and exec fault. Since we now enforce that the later only work if
VM_EXEC is part of the VMA flags, we de-fact already enforce per-page
execute permissions... Unless I missed something
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This avoids having a short glitch if the desired initial value is not
the same as what was previously in the data register.
Signed-off-by: Michael Barkowski <michaelbarkowski@ruggedcom.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Add gpio-controller node for BCSR17, it is used to control USB
speed and VBUS;
- Add timer node for QE GTM, needed for USB host;
- Add usb node itself;
- Add some probing code for BCSR GPIOs.
NOTE: QE USB doesn't work on prototype boards, but should work on
pilot boards if specs and schematics are correct, though we
don't have the pilot boards to actually test it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Add usb node;
- Configure pins and clocks;
- Enable USB function in BCSR.
The support was successfully tested using serial and ethernet gadget
drivers.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
mpc8272_ads.c is using BCSR bits definitions from pq2ads.h, but
according to User's Guide the bits are wrong for MPC8272ADS boards
(I guess definitions from pq2ads should only be used for PQ2FADS
boards).
So, let's introduce our own definitions for MPC8272ADS, and don't
include pq2ads.h.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch simply adds sdhci node to the device tree.
We specify clock-frequency manually, so that eSDHC will work without
upgrading U-Boot. Though, that'll only work for default setup (1500
MHz) on new board revisions. For non-default setups, it's recommended
to upgrade U-Boot, since it will fixup clock-frequency automatically.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The earlier mpc8560 CPUs don't have the RSTCR at 0xe00b0
in the GUTS. The generic reboot code uses this tag to
determine if it should be using the RSTCR for reboot, so
remove it from the board definition.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some CPU, like the MPC8560 don't have a RSTCR in the Global
Utilities Block. These boards will implement their own reboot
call, and not use this code, so we should only warn about the
absence of the GUTS RSTCR when the default reboot code is used.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The existing fsl_rstcr_restart function is not applicable to the
mpc8560. The Global Utilities Block on this earlier CPU doesn't have
the control/reset register at 0xe00b0. This implements a board
specific reset function that uses the RCR(Reset Control Register) of
the sbc8560's EPLD to do a reset.
Signed-off-by: Liang Li <Liang.Li@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
With flash partition entries in the DTS file, MTD might as well
be enabled in the defconfig. In a similar vein, enable USB and
enough related options (SCSI/ext2/ext3) so that a user can read
and write to a generic USB flash drive as well.
Also, this board only has the two default SOC UARTs, so adjust the
UART config accordingly.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Allows interrupts to occur on the sbc834x. Currently PCI devices
get assigned an incorrect IRQ and so the interrupt count never
increases. This was tested with the 82546GB based dual port E1000
PCI-X NIC which uses two distinct IRQ lines on the one card.
root@localhost:/root> cat /proc/interrupts | grep eth
17: 78 IPIC Level eth1
48: 27121 IPIC Level eth0
Signed-off-by: Liang Li <liang.li@windriver.com>
Signed-off-by: Yang Shi <yang.shi@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There is 8MB flash, 8kB EEPROM and 128MB SDRAM on the sbc834x
local bus, so add a localbus node in DTS with MTD partitions.
The recent U-boot commit fe613cdd4eb moves u-boot to the beginning
of flash, hence the legacy label on the partition at the end of flash.
Signed-off-by: Liang Li <liang.li@windriver.com>
Signed-off-by: Yang Shi <yang.shi@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Since only one of the SoC USB devices is brought out to a physical
connector on the board, remove the 2nd (USB-DR) node from the DTS.
Having it present and USB enabled will cause a hang at boot.
Signed-off-by: Liang Li <liang.li@windriver.com>
Signed-off-by: Yang Shi <yang.shi@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MMUCSR is now defined as part of the Book-3E architecture so we
can move it into mmu-book3e.h and add some of the additional bits
defined by the architecture specs.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix the following build problem on powerpc:
arch/powerpc/kernel/time.c: In function 'read_persistent_clock':
arch/powerpc/kernel/time.c:788: error: 'return' with a value, in function returning void
arch/powerpc/kernel/time.c:791: error: 'return' with a value, in function returning void
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: dwalker@fifo99.com
Cc: johnstul@us.ibm.com
LKML-Reference: <20090822222313.74b9619c@skybase>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
gcc v4.4 currently produces this build warning:
arch/powerpc/boot/mktree.c: In function 'main':
arch/powerpc/boot/mktree.c:104: warning: dereferencing type-punned pointer will break strict-aliasing rules
tmpbuf is only used as an array of unsigned ints, so declare it that way.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently _edata does not include several data sections, this causes
the kernel's report of memory usage at boot to not match reality, and
also prevents kmemleak from working - because it scan between _sdata
and _edata for pointers to allocated memory.
This mirrors a similar change made recently to the x86 linker script.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Make it possible to enable GCOV code coverage measurement on powerpc.
Lightly tested on 64-bit, seems to work as expected.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
hardirq.h on powerpc defines a __last_jiffy_stamp field, but it's not
actually used anywhere.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d
but is perhaps more readable.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@haskernel@
@@
#include <linux/kernel.h>
@depends on haskernel@
expression x,__divisor;
@@
- (((x) + ((__divisor) / 2)) / (__divisor))
+ DIV_ROUND_CLOSEST(x,__divisor)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As <asm/iommu.h> doesn't contain any other hardware specific definitions
but only interfaces.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Evaluate mem kernel parameter for early memory allocations. If mem is set
no allocation in the region above the given boundary is allowed. The current
code doesn't take care about this and allocate memory above the given mem
boundary.
Signed-off-by: Benjamin Krill <ben@codiert.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These changes were a direct result of using a semantic patch
More information can be found at http://www.emn.fr/x-info/coccinelle/
Signed-off-by: Stoyan Gaydarov <sgayda2@uiuc.edu>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add a byte length read and write interface compatible with the
nvram_generic driver interface to the mmio driver.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I wrote sputrace before generic tracing infrastrucure was available.
Now that we have the generic event tracer we can convert it over and
remove a lot of code:
8 files changed, 45 insertions(+), 285 deletions(-)
To use it make sure CONFIG_EVENT_TRACING is enabled and then enable
the spufs trace channel by
echo 1 > /sys/kernel/debug/tracing/events/spufs/spufs_context/enable
and then read the trace records using e.g.
cat /sys/kernel/debug/tracing/trace
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since the pte_lockptr is a spinlock it gets optimized away on
uniprocessor builds so using spin_is_locked is not correct. We can use
assert_spin_locked instead and get the proper behavior between UP and
SMP builds.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Update GE Fanuc DTS to match the alterations suggested during the merge of
the ppc9a DTS in commit 740d36ae63
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch enables the XMC (PCIe daughter card) site on the SBC310.
STG enter the description for the patch above.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
/proc/cpuinfo should be showing the boards revision and the revision of
the FPGA fitted. The functions currently used to access this information
as incorrect.
Additionally the VME geographical address of the PPC9A and it's status as
system contoller are available in the board registers. Show these in
cpuinfo.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Actually, the support is already there, but it requires newer U-Boots
(to fill-in clock-frequency, and setup pin multiplexing).
Though, it appears that on RDB boards USBB pins aren't multiplexed
between USB and eSDHC (unlike MDS boards, where USB and eSDHC share
pctl and pwrfault pins).
So, for RDB boards we can safely setup pinmux and manually fill-in
clock-frequency, thus making eSDHC work even with older u-boots.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch simply adds four eeprom nodes to MPC8548CDS' device tree.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Error handling code following a kzalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...x...+> }
(
x->f1 = E
|
(x->f1 == NULL || ...)
|
f(...,x->f1,...)
)
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Error handling code following a kzalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...x...+> }
(
x->f1 = E
|
(x->f1 == NULL || ...)
|
f(...,x->f1,...)
)
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
- add I2C support
- add FCC1 and FCC2 support
- fix bogus gpio numbering in plattform code
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
in case the interrupt controller was used in an earlier life then it is
possible it is that some of its sources were used and are still unmask.
If the (unmasked) device is active and is creating interrupts (or one
interrupts was pending since the interrupts were disabled) then the boot
process "ends" very soon. Once external interrupts are enabled, we land in
-> do_IRQ
-> call ppc_md.get_irq()
-> ipic_read() gets the source number
-> irq_linear_revmap(source)
-> revmap[source] == NO_IRQ
-> irq_find_mapping(source) returns NO_IRQ because no source
is registered
-> source is NO_IRQ, ppc_spurious_interrupts gets incremented, no
further action.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Check that the result of kmalloc/kzalloc is not NULL before dereferencing it.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression *x;
identifier f;
constant char *C;
@@
x = \(kmalloc\|kcalloc\|kzalloc\)(...);
... when != x == NULL
when != x != NULL
when != (x || ...)
(
kfree(x)
|
f(...,C,...,x,...)
|
*f(...,x,...)
|
*x->f
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
cam[tlbcam_index] is checked before tlbcam_index < ARRAY_SIZE(cam)
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Added a device tree that should be similiar to mpc8536ds.dtb except
the physical addresses for all IO are above the 4G boundary.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Change the top-level #address-cells and #size-cells to <2> so the
mpc8536ds.dts is easier to deal with both a true 32-bit physical
or 36-bit physical address space.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds support for the following devices to the Kilauea
defconfig file:
- PPC4xx NAND controller (NDFC)
- I2C RTC (Dallas DS1338)
- I2C HWMON (Dallas DS1775)
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds support for the following devices to the Canyonlands
defconfig file:
- NOR FLASH
- PPC4xx NAND controller (NDFC)
- I2C RTC (M41T80)
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds support for the following devices to the Kilauea dts:
- PPC4xx NAND controller (NDFC)
- I2C RTC (Dallas DS1338)
- I2C HWMON (Dallas DS1775)
Additionally the partitioning of the NOR FLASH is changed. The dtb
partition has been missing. Fixed in this patch.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Also some whitespace cleanup in the USB device nodes.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Introduced a temporary variable into our iterating over the list cpus
that are threads on the same core. For some reason Ben forgot how for
loops work.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The mask used to encode the page table cache number in the
batch when freeing page tables was too small for the new
possible values of MMU page sizes. This increases it along
with a comment explaining the constraints.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This contains all the bits that didn't fit in previous patches :-) This
includes the actual exception handlers assembly, the changes to the
kernel entry, other misc bits and wiring it all up in Kconfig.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The base TLB support didn't include support for SPARSEMEM_VMEMMAP, though
we did carve out some virtual space for it, the necessary support code
wasn't there. This implements it by using 16M pages for now, though the
page size could easily be changed at runtime if necessary.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds the TLB miss handler assembly, the low level TLB flush routines
along with the necessary hook for dealing with our virtual page tables
or indirect TLB entries that need to be flushes when PTE pages are freed.
There is currently no support for hugetlbfs
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The definition for the global structure mmu_gathers, used by generic code,
is currently defined in multiple places not including anything used by
64-bit Book3E. This changes it by moving to one place common to all
processors.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds various fields in the PACA that are for use specifically
by Book3E processors, such as exception save areas, current pgd
pointer, special exceptions kernel stacks etc...
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds various definitions and macros used by the exception and TLB
miss handling on 64-bit BookE
It also adds the definitions of the SPRGs used for various exception types
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds the PTE and pgtable format definitions, along with changes
to the kernel memory map and other definitions related to implementing
support for 64-bit Book3E. This also shields some asm-offset bits that
are currently only relevant on 32-bit
We also move the definition of the "linux" page size constants to
the common mmu.h file and add a few sizes that are relevant to
embedded processors.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds various SPRs defined on 64-bit BookE, along with changes
to the definition of the base MSR values to add the values needed
for 64-bit Book3E.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
That patch used to just add a hook to page table flushing but
pulling that string brought out a whole bunch of issues, so it
now does that and more:
- We now make the RCU batching of page freeing SMP only, as I
believe it was intended initially. We make a few more things compile
to nothing on !CONFIG_SMP
- Some macros are turned into functions, though that forced me to
out of line a few stuffs due to unsolvable include depenencies,
however it's probably better that way anyway, it's not -that-
critical code path.
- 32-bit didn't call pte_free_finish() on tlb_flush() which means
that it wouldn't push out the batch to RCU for delayed freeing when
a bunch of page tables have been freed, they would just stay in there
until the batch gets full.
64-bit BookE will use that hook to maintain the virtually linear
page tables or the indirect entries in the TLB when using the
HW loader.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Those definitions are currently declared extern in the .c file where
they are used, move them to a header file instead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, a single ifdef covers SLB related bits and more generic ppc64
related bits, split this in two separate ifdef's since 64-bit BookE will
need one but not the other.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Our 64-bit hash context handling has no init function, but 64-bit Book3E
will use the common mmu_context_nohash.c code which does, so define an
empty inline mmu_context_init() for 64-bit server and call it from
our 64-bit setup_arch()
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
We need to pass down whether the page is direct or indirect and we'll
need to pass the page size to _tlbil_va and _tlbivax_bcast
We also add a new low level _tlbil_pid_noind() which does a TLB flush
by PID but avoids flushing indirect entries if possible
This implements those new prototypes but defines them with inlines
or macros so that no additional arguments are actually passed on current
processors.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The way I intend to use tophys/tovirt on 64-bit BookE is different
from the "trick" that we currently play for 32-bit BookE so change
the condition of definition of these macros to make it so.
Also, make sure we only use rfid and mtmsrd instead of rfi and mtmsr
for 64-bit server processors, not all 64-bit processors.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
This adds some code to do early ioremap's using page tables instead of
bolting entries in the hash table. This will be used by the upcoming
64-bits BookE port.
The patch also changes the test for early vs. late ioremap to use
slab_is_available() instead of our old hackish mem_init_done.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds various additional bit definitions for various MMU related
SPRs used on Book3E.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds the opcode definitions to ppc-opcode.h for the two instructions
tlbivax and tlbsrx. as defined by Book3E 2.06
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The current "no hash" MMU context management code is written with
the assumption that one CPU == one TLB. This is not the case on
implementations that support HW multithreading, where several
linux CPUs can share the same TLB.
This adds some basic support for this to our context management
and our TLB flushing code.
It also cleans up the optional debugging output a bit
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
enter_prom() used to save and restore registers such as CTR, XER etc..
which are volatile, or SRR0,1... which we don't care about. This
removes a bunch of useless code and while at it turns an mtmsrd into
an MTMSRD macro which will be useful to Book3E.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A misplaced #endif causes more definitions than intended to be
protected by #ifndef __ASSEMBLY__. This breaks upcoming 64-bit
BookE support patch when using 64k pages.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The truncate syscall has a signed long parameter, so when using a 32-
bit userspace with a 64-bit kernel the argument is zero-extended
instead of sign-extended. Adding the compat_sys_truncate function
fixes the issue.
This was noticed during an LSB truncate test failure. The test was
checking for the correct error number set when truncate is called with
a length of -1. The test can be found at:
http://bzr.linuxfoundation.org/lsb/devel/runtime-test?cmd=inventory;rev=stewb%40linux-foundation.org-20090626205411-sfb23cc0tjj7jzgm;path=modules/vsx-pcts/tset/POSIX.os/files/truncate/
BenH: Added compat_sys_ftruncate() as well, same issue.
Signed-off-by: Chase Douglas <cndougla@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
dtc was moved in 9fffb55f66 from
arch/powerpc/boot/ to scripts/dtc/
This patch updates the wrapper script to point to the new location of dtc.
Signed-off-by: Lucian Adrian Grijincu <lgrijincu@ixiacom.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This change the SPRG used to store the PACA on ppc64 from
SPRG3 to SPRG1. SPRG3 is user readable on most processors
and we want to use it for other things. We change the scratch
SPRG used by exception vectors from SRPG1 to SPRG2.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The code for setting up the IPIs for SMP PowerSurge marchines bitrot,
it needs to properly map the HW interrupt number
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The current definitions set ranges and defaults for 32 and 64-bit
only using "PPC_STD_MMU" which means hash based MMU. This uselessly
restrict the usefulness for the upcoming 64-bit BookE port, but more
than that, it's broken on 32-bit since the only 32-bit platform
supporting multiple page sizes currently is 44x which does -not-
have PPC_STD_MMU_32 set.
This fixes it by using PPC64 and PPC32 instead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Replace strncpy() and explicit null-termination by strlcpy()
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The STAB code used on Power3 and RS/64 uses a second scratch SPRG to
save a GPR in order to decide whether to go to do_stab_bolted_* or
to handle a normal data access exception.
This prevents our scheme of freeing SPRG3 which is user visible for
user uses since we cannot use SPRG0 which, on RS/64, seems to be
read-only for supervisor mode (like POWER4).
This reworks the STAB exception entry to use the PACA as temporary
storage instead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The kernel uses SPRG registers for various purposes, typically in
low level assembly code as scratch registers or to hold per-cpu
global infos such as the PACA or the current thread_info pointer.
We want to be able to easily shuffle the usage of those registers
as some implementations have specific constraints realted to some
of them, for example, some have userspace readable aliases, etc..
and the current choice isn't always the best.
This patch should not change any code generation, and replaces the
usage of SPRN_SPRGn everywhere in the kernel with a named replacement
and adds documentation next to the definition of the names as to
what those are used for on each processor family.
The only parts that still use the original numbers are bits of KVM
or suspend/resume code that just blindly needs to save/restore all
the SPRGs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The file include/asm/exception.h contains definitions
that are specific to exception handling on 64-bit server
type processors.
This renames the file to exception-64s.h to reflect that
fact and avoid confusion.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
TASK_UNMAPPED_BASE is not used with the new top down mmap layout. We can
reuse this preload slot by loading in the segment at 0x10000000, where almost
all PowerPC binaries are linked at.
On a microbenchmark that bounces a token between two 64bit processes over pipes
and calls gettimeofday each iteration (to access the VDSO), both the 32bit and
64bit context switch rate improves (tested on a 4GHz POWER6):
32bit: 273k/sec -> 283k/sec
64bit: 277k/sec -> 284k/sec
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With the new top down layout it is likely that the pc and stack will be in the
same segment, because the pc is most likely in a library allocated via a top
down mmap. Right now we bail out early if these segments match.
Rearrange the SLB preload code to sanity check all SLB preload addresses
are not in the kernel, then check all addresses for conflicts.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On 64bit applications the VDSO is the only thing in segment 0. Since the VDSO
is position independent we can remove the hint and let get_unmapped_area pick
an area. This will mean the vdso will be near other mmaps and will share
an SLB entry:
10000000-10001000 r-xp 00000000 08:06 5778459 /root/context_switch_64
10010000-10011000 r--p 00000000 08:06 5778459 /root/context_switch_64
10011000-10012000 rw-p 00001000 08:06 5778459 /root/context_switch_64
fffa92ae000-fffa92b0000 rw-p 00000000 00:00 0
fffa92b0000-fffa9453000 r-xp 00000000 08:06 4334051 /lib64/power6/libc-2.9.so
fffa9453000-fffa9462000 ---p 001a3000 08:06 4334051 /lib64/power6/libc-2.9.so
fffa9462000-fffa9466000 r--p 001a2000 08:06 4334051 /lib64/power6/libc-2.9.so
fffa9466000-fffa947c000 rw-p 001a6000 08:06 4334051 /lib64/power6/libc-2.9.so
fffa947c000-fffa9480000 rw-p 00000000 00:00 0
fffa9480000-fffa94a8000 r-xp 00000000 08:06 4333852 /lib64/ld-2.9.so
fffa94b3000-fffa94b4000 rw-p 00000000 00:00 0
fffa94b4000-fffa94b7000 r-xp 00000000 00:00 0 [vdso] <----- here I am
fffa94b7000-fffa94b8000 r--p 00027000 08:06 4333852 /lib64/ld-2.9.so
fffa94b8000-fffa94bb000 rw-p 00028000 08:06 4333852 /lib64/ld-2.9.so
fffa94bb000-fffa94bc000 rw-p 00000000 00:00 0
fffe4c10000-fffe4c25000 rw-p 00000000 00:00 0 [stack]
On a microbenchmark that bounces a token between two 64bit processes over pipes
and calls gettimeofday each iteration (to access the VDSO), our context switch
rate goes from 268k to 277k ctx switches/sec (tested on a 4GHz POWER6).
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The bitops.h functions that operate on a single bit in a bitfield are
implemented by operating on the corresponding word location. In all
cases the inner logic is valid if the mask being applied has more than
one bit set, so this patch exposes those inner operations. Indeed,
set_bits() was already available, but it duplicated code from
set_bit() (rather than making the latter a wrapper) - it was also
missing the PPC405_ERR77() workaround and the "volatile" address
qualifier present in other APIs. This corrects that, and exposes the
other multi-bit equivalents.
One advantage of these multi-bit forms is that they allow word-sized
variables to essentially be their own spinlocks, eg. very useful for
state machines where an atomic "flags" variable can obviate the need
for any additional locking.
Signed-off-by: Geoff Thorpe <geoff@geoffthorpe.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The workaround enabled by CONFIG_MPIC_BROKEN_REGREAD does not work
on non-broken MPICs. The symptom is no interrupts being received.
The fix is twofold. Firstly the code was broken for multiple isus,
we need to index into the shadow array with the src_no, not the idx.
Secondly, we always do the read, but only use the VECPRI_MASK and
VECPRI_ACTIVITY bits from the hardware, the rest of "val" comes
from the shadow.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This allows to remove the ppc_md.init() hook in the setup code.
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds support for tracing callchains for powerpc, both 32-bit
and 64-bit, and both in the kernel and userspace, from PMU interrupt
context.
The first three entries stored for each callchain are the NIP (next
instruction pointer), LR (link register), and the contents of the LR
save area in the second stack frame (the first is ignored because the
ABI convention on powerpc is that functions save their return address
in their caller's stack frame). Because leaf functions don't have to
save their return address (LR value) and don't have to establish a
stack frame, it's possible for either or both of LR and the second
stack frame's LR save area to have valid return addresses in them.
This is basically impossible to disambiguate without either reading
the code or looking at auxiliary information such as CFI tables.
Since we don't want to do either of those things at interrupt time,
we store both LR and the second stack frame's LR save area.
Once we get past the second stack frame, there is no ambiguity; all
return addresses we get are reliable.
For kernel traces, we check whether they are valid kernel instruction
addresses and store zero instead if they are not (rather than
omitting them, which would make it impossible for userspace to know
which was which). We also store zero instead of the second stack
frame's LR save area value if it is the same as LR.
For kernel traces, we check for interrupt frames, and for user traces,
we check for signal frames. In each case, since we're starting a new
trace, we store a PERF_CONTEXT_KERNEL/USER marker so that userspace
knows that the next three entries are NIP, LR and the second stack frame
for the interrupted context.
We read user memory with __get_user_inatomic. On 64-bit, if this
PMU interrupt occurred while interrupts are soft-disabled, and
there is no MMU hash table entry for the page, we will get an
-EFAULT return from __get_user_inatomic even if there is a valid
Linux PTE for the page, since hash_page isn't reentrant. Thus we
have code here to read the Linux PTE and access the page via the
kernel linear mapping. Since 64-bit doesn't use (or need) highmem
there is no need to do kmap_atomic. On 32-bit, we don't do soft
interrupt disabling, so this complication doesn't occur and there
is no need to fall back to reading the Linux PTE, since hash_page
(or the TLB miss handler) will get called automatically if necessary.
Note that we cannot get PMU interrupts in the interval during
context switch between switch_mm (which switches the user address
space) and switch_to (which actually changes current to the new
process). On 64-bit this is because interrupts are hard-disabled
in switch_mm and stay hard-disabled until they are soft-enabled
later, after switch_to has returned. So there is no possibility
of trying to do a user stack trace when the user address space is
not current's address space.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This provides a mechanism to allow the perf_counters code to access
user memory in a PMU interrupt routine. Such an access can cause
various kinds of interrupt: SLB miss, MMU hash table miss, segment
table miss, or TLB miss, depending on the processor. This commit
only deals with 64-bit classic/server processors, which use an MMU
hash table. 32-bit processors are already able to access user memory
at interrupt time. Since we don't soft-disable on 32-bit, we avoid
the possibility of reentering hash_page or the TLB miss handlers,
since they run with interrupts disabled.
On 64-bit processors, an SLB miss interrupt on a user address will
update the slb_cache and slb_cache_ptr fields in the paca. This is
OK except in the case where a PMU interrupt occurs in switch_slb,
which also accesses those fields. To prevent this, we hard-disable
interrupts in switch_slb. Interrupts are already soft-disabled at
this point, and will get hard-enabled when they get soft-enabled
later.
This also reworks slb_flush_and_rebolt: to avoid hard-disabling twice,
and to make sure that it clears the slb_cache_ptr when called from
other callers than switch_slb, the existing routine is renamed to
__slb_flush_and_rebolt, which is called by switch_slb and the new
version of slb_flush_and_rebolt.
Similarly, switch_stab (used on POWER3 and RS64 processors) gets a
hard_irq_disable() to protect the per-cpu variables used there and
in ste_allocate.
If a MMU hashtable miss interrupt occurs, normally we would call
hash_page to look up the Linux PTE for the address and create a HPTE.
However, hash_page is fairly complex and takes some locks, so to
avoid the possibility of deadlock, we check the preemption count
to see if we are in a (pseudo-)NMI handler, and if so, we don't call
hash_page but instead treat it like a bad access that will get
reported up through the exception table mechanism. An interrupt
whose handler runs even though the interrupt occurred when
soft-disabled (such as the PMU interrupt) is considered a pseudo-NMI
handler, which should use nmi_enter()/nmi_exit() rather than
irq_enter()/irq_exit().
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On 32-bit systems with 64-bit PTEs, the PTEs have to be written in two
32-bit halves. On SMP we write the higher-order half and then the
lower-order half, with a write barrier between the two halves, but on
UP there was no particular ordering of the writes to the two halves.
This extends the ordering that we already do on SMP to the UP case as
well. The reason is that with the perf_counter subsystem potentially
accessing user memory at interrupt time to get stack traces, we have
to be careful not to create an incorrect but apparently valid PTE even
on UP.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The persistent clock of some architectures (e.g. s390) have a
better granularity than seconds. To reduce the delta between the
host clock and the guest clock in a virtualized system change the
read_persistent_clock function to return a struct timespec.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
LKML-Reference: <20090814134811.013873340@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Now that percpu allows arbitrary embedding of the first chunk,
powerpc64 can easily be converted to dynamic percpu allocator.
Convert it. powerpc supports several large page sizes. Cap atom_size
at 1M. There isn't much to gain by going above that anyway.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Conflicts:
arch/sparc/kernel/smp_64.c
arch/x86/kernel/cpu/perf_counter.c
arch/x86/kernel/setup_percpu.c
drivers/cpufreq/cpufreq_ondemand.c
mm/percpu.c
Conflicts in core and arch percpu codes are mostly from commit
ed78e1e078dd44249f88b1dd8c76dafb39567161 which substituted many
num_possible_cpus() with nr_cpu_ids. As for-next branch has moved all
the first chunk allocators into mm/percpu.c, the changes are moved
from arch code to mm/percpu.c.
Signed-off-by: Tejun Heo <tj@kernel.org>
* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (27 commits)
perf_counter: Zero dead bytes from ftrace raw samples size alignment
perf_counter: Subtract the buffer size field from the event record size
perf_counter: Require CAP_SYS_ADMIN for raw tracepoint data
perf_counter: Correct PERF_SAMPLE_RAW output
perf tools: callchain: Fix bad rounding of minimum rate
perf_counter tools: Fix libbfd detection for systems with libz dependency
perf: "Longum est iter per praecepta, breve et efficax per exempla"
perf_counter: Fix a race on perf_counter_ctx
perf_counter: Fix tracepoint sampling to be part of generic sampling
perf_counter: Work around gcc warning by initializing tracepoint record unconditionally
perf tools: callchain: Fix sum of percentages to be 100% by displaying amount of ignored chains in fractal mode
perf tools: callchain: Fix 'perf report' display to be callchain by default
perf tools: callchain: Fix spurious 'perf report' warnings: ignore empty callchains
perf record: Fix the -A UI for empty or non-existent perf.data
perf util: Fix do_read() to fail on EOF instead of busy-looping
perf list: Fix the output to not include tracepoints without an id
perf_counter/powerpc: Fix oops on cpus without perf_counter hardware support
perf stat: Fix tool option consistency: rename -S/--scale to -c/--scale
perf report: Add debug help for the finding of symbol bugs - show the symtab origin (DSO, build-id, kernel, etc)
perf report: Fix per task mult-counter stat reporting
...
On an iMac G5, the b43 driver is failing to initialise because trying to
set the dma mask to 30-bit fails. Even though there's only 512MiB of RAM
in the machine anyway:
https://bugzilla.redhat.com/show_bug.cgi?id=514787
We should probably let it succeed if the available RAM in the system
doesn't exceed the requested limit.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'kvm-updates/2.6.31' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Avoid redelivery of edge interrupt before next edge
KVM: MMU: limit rmap chain length
KVM: ia64: fix build failures due to ia64/unsigned long mismatches
KVM: Make KVM_HPAGES_PER_HPAGE unsigned long to avoid build error on powerpc
KVM: fix ack not being delivered when msi present
KVM: s390: fix wait_queue handling
KVM: VMX: Fix locking imbalance on emulation failure
KVM: VMX: Fix locking order in handle_invalid_guest_state
KVM: MMU: handle n_free_mmu_pages > n_alloc_mmu_pages in kvm_mmu_change_mmu_pages
KVM: SVM: force new asid on vcpu migration
KVM: x86: verify MTRR/PAT validity
KVM: PIT: fix kpit_elapsed division by zero
KVM: Fix KVM_GET_MSR_INDEX_LIST
If we have the powerpc perf_counter backend compiled in, but
the cpu we are running on is one where we don't support the
PMU, we currently oops in hw_perf_group_sched_in if we try to
use any counters, because ppmu is NULL in that case, and we
unconditionally dereference ppmu.
This fixes the problem by adding a check if ppmu is NULL at the
beginning of hw_perf_group_sched_in, and also at the beginning
of the other functions that get called from the perf_counter
core, i.e. hw_perf_disable, hw_perf_enable, and
hw_perf_counter_setup.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: benh@kernel.crashing.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If the current CPU doesn't support performance counters,
cur_cpu_spec->oprofile_cpu_type can be NULL. The current
perf_counter modules don't test for that case and would thus
crash at boot time.
Bug reported by David Woodhouse.
Reported-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Paul Mackerras <paulus@samba.org>
LKML-Reference: <19066.48028.446975.501454@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This sockopt goes in line with SO_TYPE and SO_PROTOCOL. It makes it
possible for userspace programs to pass around file descriptors — I
am referring to arguments-to-functions, but it may even work for the
fd passing over UNIX sockets — without needing to also pass the
auxiliary information (PF_INET6/IPPROTO_TCP).
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to SO_TYPE returning the socket type, SO_PROTOCOL allows to
retrieve the protocol used with a given socket.
I am not quite sure why we have that-many copies of socket.h, and why
the values are not the same on all arches either, but for where hex
numbers dominate, I use 0x1029 for SO_PROTOCOL as that seems to be
the next free unused number across a bunch of operating systems, or
so Google results make me want to believe. SO_PROTOCOL for others
just uses the next free Linux number, 38.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminates this compiler warning:
arch/powerpc/kvm/../../../virt/kvm/kvm_main.c:1178: error: integer overflow in expression
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Avi Kivity <avi@redhat.com>
For powerpc with CONFIG_VIRT_CPU_ACCOUNTING
jiffies_to_cputime(1) is not compile time constant and run time
calculations are quite expensive. To optimize we use
precomputed value. For all other architectures is is
preprocessor definition.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
LKML-Reference: <1248862529-6063-5-git-send-email-sgruszka@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
General update of defconfig including the following notable changes:
- Enable Highmem support.
- Support for PCMCIA based daughter card.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
General update of defconfig including the following notable changes:
- Enable GPIO access via sysfs on GE Fanuc's PPC9A.
- Enable Highmem support.
- Support for PCMCIA based daughter card.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
U-Boot maps PCI IO at 0xe0300000, while current dts files specify
0xe2000000. This leads to the following oops with CONFIG_8139TOO_PIO=y.
8139too Fast Ethernet driver 0.9.28
Machine check in kernel mode.
Caused by (from SRR1=41000): Transfer error ack signal
Oops: Machine check, sig: 7 [#1]
MPC837x RDB
[...]
NIP [00000900] 0x900
LR [c0439df8] rtl8139_init_board+0x238/0x524
Call Trace:
[cf831d90] [c0439dcc] rtl8139_init_board+0x20c/0x524 (unreliable)
[cf831de0] [c043a15c] rtl8139_init_one+0x78/0x65c
[cf831e40] [c0235250] pci_call_probe+0x20/0x30
[...]
This patch fixes the issue by specifying the correct PCI IO base
address.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Sometimes (e.g. when there are no UEMs attached to a board)
fsl_pq_mdio_find_free() fails to find a spare address for a TBI PHY,
this is because get_phy_id() returns bogus 0x0000ffff values
(0xffffffff is expected), and therefore mdio bus probing fails with
the following message:
fsl-pq_mdio: probe of e0082120.mdio failed with error -16
And obviously ethernet doesn't work after this.
This patch solves the problem by adding tbi-phy node into mdio node,
so that we won't scan for spare addresses, we'll just use a fixed one.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Linux isn't able to detect link changes on ethernet ports that were
used by U-Boot. This is because U-Boot wrongly clears interrupt
polarity bit (INTPOL, 0x400) in the extended status register (EXT_SR,
0x1b) of Marvell PHYs.
There is no easy way for PHY drivers to know IRQ line polarity (we
could extract it from the device tree and pass it to phydevs, but
that'll be quite a lot of work), so for now just reset the PHYs to
their default states.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In switch_mmu_context() if we call steal_context_smp() to get a context
to use we shouldn't fall through and than call steal_context_up(). Doing
so can be problematic in that the 'mm' that steal_context_up() ends up
using will not get marked dirty in the stale_map[] for other CPUs that
might have used that mm. Thus we could end up with stale TLB entries in
the other CPUs that can cause all kinda of havoc.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
phys_to_dma() and dma_to_phys() are used instead of
swiotlb_phys_to_bus() and swiotlb_bus_to_phys().
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Becky Bruce <beckyb@kernel.crashing.org>
This adds two functions, phys_to_dma() and dma_to_phys() to x86, IA64
and powerpc. swiotlb uses them. phys_to_dma() converts a physical
address to a dma address. dma_to_phys() does the opposite.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Becky Bruce <beckyb@kernel.crashing.org>
swiotlb doesn't use swiotlb_arch_address_needs_mapping(); it uses
dma_capalbe(). We can remove unnecessary
swiotlb_arch_address_needs_mapping().
We can remove swiotlb_addr_needs_map() and is_buffer_dma_capable() in
swiotlb_pci_addr_needs_map() too; dma_capable() handles the features
that both provide.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Becky Bruce <beckyb@kernel.crashing.org>
dma_capable() eventually replaces is_buffer_dma_capable(), which tells
if a memory area is dma-capable or not. The problem of
is_buffer_dma_capable() is that it doesn't take a pointer to struct
device so it doesn't work for POWERPC.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Becky Bruce <beckyb@kernel.crashing.org>
swiotlb_bus_to_virt is unncessary; we can use swiotlb_bus_to_phys and
phys_to_virt instead.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Becky Bruce <beckyb@kernel.crashing.org>
mm: Pass virtual address to [__]p{te,ud,md}_free_tlb()
Upcoming paches to support the new 64-bit "BookE" powerpc architecture
will need to have the virtual address corresponding to PTE page when
freeing it, due to the way the HW table walker works.
Basically, the TLB can be loaded with "large" pages that cover the whole
virtual space (well, sort-of, half of it actually) represented by a PTE
page, and which contain an "indirect" bit indicating that this TLB entry
RPN points to an array of PTEs from which the TLB can then create direct
entries. Thus, in order to invalidate those when PTE pages are deleted,
we need the virtual address to pass to tlbilx or tlbivax instructions.
The old trick of sticking it somewhere in the PTE page struct page sucks
too much, the address is almost readily available in all call sites and
almost everybody implemets these as macros, so we may as well add the
argument everywhere. I added it to the pmd and pud variants for consistency.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David Howells <dhowells@redhat.com> [MN10300 & FRV]
Acked-by: Nick Piggin <npiggin@suse.de>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [s390]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow architecture specific data in struct platform_device V3.
With this patch struct pdev_archdata is added to struct
platform_device, similar to struct dev_archdata in found in
struct device. Useful for architecture code that needs to
keep extra data associated with each platform device.
Struct pdev_archdata is different from dev.platform_data, the
convention is that dev.platform_data points to driver-specific
data. It may or may not be required by the driver. The format
of this depends on driver but is the same across architectures.
The structure pdev_archdata is a place for architecture specific
data. This data is handled by architecture specific code (for
example runtime PM), and since it is architecture specific it
should _never_ be touched by device driver code. Exactly like
struct dev_archdata but for platform devices.
[rjw: This change is for power management mostly and that's why it
goes through the suspend tree.]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
When moving load_up_altivec to vector.S a typo in a comment caused a
thinko setting the wrong variable.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On booke processors, gdb is seeing spurious SIGTRAPs when setting a
watchpoint.
user_disable_single_step() simply quits when the DAC is non-zero. It should
be clearing the DBCR0_IC and DBCR0_BT bits from the dbcr0 register and
TIF_SINGLESTEP from the thread flag.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (50 commits)
perf report: Add "Fractal" mode output - support callchains with relative overhead rate
perf_counter tools: callchains: Manage the cumul hits on the fly
perf report: Change default callchain parameters
perf report: Use a modifiable string for default callchain options
perf report: Warn on callchain output request from non-callchain file
x86: atomic64: Inline atomic64_read() again
x86: atomic64: Clean up atomic64_sub_and_test() and atomic64_add_negative()
x86: atomic64: Improve atomic64_xchg()
x86: atomic64: Export APIs to modules
x86: atomic64: Improve atomic64_read()
x86: atomic64: Code atomic(64)_read and atomic(64)_set in C not CPP
x86: atomic64: Fix unclean type use in atomic64_xchg()
x86: atomic64: Make atomic_read() type-safe
x86: atomic64: Reduce size of functions
x86: atomic64: Improve atomic64_add_return()
x86: atomic64: Improve cmpxchg8b()
x86: atomic64: Improve atomic64_read()
x86: atomic64: Move the 32-bit atomic64_t implementation to a .c file
x86: atomic64: The atomic64_t data type should be 8 bytes aligned on 32-bit too
perf report: Annotate variable initialization
...
Pull the initial preempt_count value into a single
definition site.
Maintainers for: alpha, ia64 and m68k, please have a look,
your arch code is funny.
The header magic is a bit odd, but similar to the KERNEL_DS
one, CPP waits with expanding these macros until the
INIT_THREAD_INFO macro itself is expanded, which is in
arch/*/kernel/init_task.c where we've already included
sched.h so we're good.
Cc: tony.luck@intel.com
Cc: rth@twiddle.net
Cc: geert@linux-m68k.org
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Discarded sections in different archs share some commonality but have
considerable differences. This led to linker script for each arch
implementing its own /DISCARD/ definition, which makes maintaining
tedious and adding new entries error-prone.
This patch makes all linker scripts to move discard definitions to the
end of the linker script and use the common DISCARDS macro. As ld
uses the first matching section definition, archs can include default
discarded sections by including them earlier in the linker script.
ia64 is notable because it first throws away some ia64 specific
subsections and then include the rest of the sections into the final
image, so those sections must be discarded before the inclusion.
defconfig compile tested for x86, x86-64, powerpc, powerpc64, ia64,
alpha, sparc, sparc64 and s390. Michal Simek tested microblaze.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Michal Simek <monstr@monstr.eu>
Cc: linux-arch@vger.kernel.org
Cc: Michal Simek <monstr@monstr.eu>
Cc: microblaze-uclinux@itee.uq.edu.au
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Tony Luck <tony.luck@intel.com>
Current implementation of spin_event_timeout can be interrupted by an
IRQ or context switch after testing the condition, but before checking
the timeout. This can cause the loop to report a timeout when the
condition actually became true in the middle.
This patch adds one final check of the condition upon exit of the loop
if the last test of the condition was still false.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pr_debug() can now result in code being generated even when DEBUG
is not defined. That's not really desirable in some places.
With CONFIG_DYNAMIC_DEBUG=y:
size before:
text data bss dec hex filename
2036 368 8 2412 96c arch/powerpc/mm/pgtable.o
size after:
text data bss dec hex filename
1677 248 8 1933 78d arch/powerpc/mm/pgtable.o
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pr_debug() can now result in code being generated even when DEBUG
is not defined. That's not really desirable in some places.
With CONFIG_DYNAMIC_DEBUG=y:
size before:
text data bss dec hex filename
7083 1616 0 8699 21fb arch/powerpc/../axon_msi.o
size after:
text data bss dec hex filename
5772 1208 0 6980 1b44 arch/powerpc/../axon_msi.o
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pr_debug() can now result in code being generated even when DEBUG
is not defined. That's not really desirable in some places.
With CONFIG_DYNAMIC_DEBUG=y:
size before:
text data bss dec hex filename
3252 384 0 3636 e34 arch/powerpc/mm/gup.o
size after:
text data bss dec hex filename
2576 96 0 2672 a70 arch/powerpc/mm/gup.o
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pr_debug() can now result in code being generated even when DEBUG
is not defined. That's not really desirable in some places.
With CONFIG_DYNAMIC_DEBUG=y:
size before:
text data bss dec hex filename
3261 416 4 3681 e61 arch/powerpc/mm/slb.o
size after:
text data bss dec hex filename
2861 248 4 3113 c29 arch/powerpc/mm/slb.o
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pr_debug() can now result in code being generated even when DEBUG
is not defined. That's not really desirable in some places.
With CONFIG_DYNAMIC_DEBUG=y:
size before:
text data bss dec hex filename
1508 48 28 1584 630 powerpc/mm/mmu_context_nohash.o
size after:
text data bss dec hex filename
1088 0 28 1116 45c powerpc/mm/mmu_context_nohash.o
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pr_debug() can now result in code being generated even when DEBUG
is not defined. That's not really desirable in some places.
With CONFIG_DYNAMIC_DEBUG=y:
size before:
text data bss dec hex filename
7720 5488 296 13504 34c0 platforms/pseries/xics.o
size after:
text data bss dec hex filename
7535 5456 296 13287 33e7 platforms/pseries/xics.o
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pr_debug() can now result in code being generated even when DEBUG
is not defined. That's not really desirable in some places.
In particular, pSeries_lpar_hpte_insert() goes from 185 instructions
to 77 instructions as a result of this patch. Luckily that code
isn't called very often ...
With CONFIG_DYNAMIC_DEBUG=y:
size before:
text data bss dec hex filename
7284 1552 296 9132 23ac platforms/pseries/lpar.o
size after:
text data bss dec hex filename
5806 1096 296 7198 1c1e platforms/pseries/lpar.o
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With -Werror enabled during the build, the warp.c file fails to build
due to the temp_isr function not containing a return statement. This
fixes the build error and documents that the function never returns.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The GPIO LEDS driver now has a default state of "keep". Update the Warp DTS
and platform file to take advantage of this new state. This removes the
hardcoding of the two LEDs on the Warp.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Pull linus#master to merge PER_CPU_DEF_ATTRIBUTES and alpha build fix
changes. As alpha in percpu tree uses 'weak' attribute instead of
inline assembly, there's no need for __used attribute.
Conflicts:
arch/alpha/include/asm/percpu.h
arch/mn10300/kernel/vmlinux.lds.S
include/linux/percpu-defs.h
POWER7 has the same PR/HV bit layout as POWER6, so set the flag.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: a.p.zijlstra@chello.nl
Cc: benh@kernel.crashing.org
LKML-Reference: <20090701030701.GI3563@kryten>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (47 commits)
perf report: Add --symbols parameter
perf report: Add --comms parameter
perf report: Add --dsos parameter
perf_counter tools: Adjust only prelinked symbol's addresses
perf_counter: Provide a way to enable counters on exec
perf_counter tools: Reduce perf stat measurement overhead/skew
perf stat: Use percentages for scaling output
perf_counter, x86: Update x86_pmu after WARN()
perf stat: Micro-optimize the code: memcpy is only required if no event is selected and !null_run
perf stat: Improve output
perf stat: Fix multi-run stats
perf stat: Add -n/--null option to run without counters
perf_counter tools: Remove dead code
perf_counter: Complete counter swap
perf report: Print sorted callchains per histogram entries
perf_counter tools: Prepare a small callchain framework
perf record: Fix unhandled io return value
perf_counter tools: Add alias for 'l1d' and 'l1i'
perf-report: Add bare minimum PERF_EVENT_READ parsing
perf-report: Add modes for inherited stats and no-samples
...
When using 64k page sizes, our PTE pages are split in two halves,
the second half containing the "extension" used to keep track of
individual 4k pages when not using HW 64k pages.
However, our page tables used for hugetlb have a slightly different
format and don't carry that "second half".
Our code that batched PTEs to be invalidated unconditionally reads
the "second half" (to put it into the batch), which means that when
called to invalidate hugetlb PTEs, it will access unrelated memory.
It breaks when CONFIG_DEBUG_PAGEALLOC is enabled.
This fixes it by only accessing the second half when the _PAGE_COMBO
bit is set in the first half, which indicates that we are dealing with
a "combo" page which represents 16x4k subpages. Anything else shouldn't
have this bit set and thus not require loading from the second half.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The function udbg_44x_as1_flush() has the wrong prototype causing
a warning when enabling 440 early debug.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
dev_set_name() takes a format string, so use it properly and avoid
a warning with recent gcc's
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
spin_lock() can hang if called while the timebase is frozen,
so use a raw lock instead, also disable interrupts while
at it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Several platforms use their own copy of what is essentially the same code,
using RTAS to synchronize the timebases when bringing up new CPUs. This
moves it all into a single common implementation and additionally
turns the spinlock into a raw spinlock since the former can rely on
the timebase not being frozen when spinlock debugging is enabled, and finally
masks interrupts while the timebase is disabled.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
RTAS currently uses a normal spinlock. However it can be called from
contexts where this is not necessarily a good idea. For example, it
can be called while syncing timebases, with the core timebase being
frozen. Unfortunately, that will deadlock in case of lock contention
when spinlock debugging is enabled as the spin lock debugging code
will try to use __delay() which ... relies on the timebase being
enabled.
Also RTAS can be used in some low level IRQ handling code path so it
may as well be a raw spinlock for -rt sake.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Based on initial work from: Dale Farnsworth <dale@farnsworth.org>
Add the low level irq tracing hooks for 32-bit powerpc needed
to enable full lockdep functionality.
The approach taken to deal with the code in entry_32.S is that
we don't trace all the transitions of MSR:EE when we just turn
it off to peek at TI_FLAGS without races. Only when we are
calling into C code or returning from exceptions with a state
that have changed from what lockdep thinks.
There's a little bugger though: If we take an exception that
keeps interrupts enabled (such as an alignment exception) while
interrupts are enabled, we will call trace_hardirqs_on() on the
way back spurriously. Not a big deal, but to get rid of it would
require remembering in pt_regs that the exception was one of the
type that kept interrupts enabled which we don't know at this
stage. (Well, we could test all cases for regs->trap but that
sucks too much).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Kumar Gala <galak@kernel.crashing.org>
The 32-bit kernel relies on some memory being mapped covering
the kernel text,data and bss at least, early during boot before
the full MMU setup is done. On 32-bit "classic" processors, this
is done using BAT registers.
On 601, the size of BATs is limited to 8M and we use 2 of them
for that initial mapping. This can become quite tight when enabling
features like lockdep, so let's use a 3rd one to bump that mapping
from 16M to 24M. We keep the 4th BAT free as it can be useful for
debugging early boot code to map things like serial ports.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Those functions are way too big to be inline, besides, kmap_atomic()
wants to call debug_kmap_atomic() which isn't exported for modules
and causes module link failures.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For some reason we've had an explicit KERN_INFO for GPR dumps. With
recent changes we get output like:
<6>GPR00: 00000000 ef855eb0 ef858000 00000001 000000d0 f1000000 ffbc8000 ffffffff
The KERN_INFO is causing the <6>. Don't see any reason to keep it
around.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The old PowerSurge SMP (ie, dual or quad 604 machines) code has
numerous issues in modern world.
One is cpu_possible_map is set too late (the device-tree is bogus)
so we fail to allocate the interrupt stacks and crash. Another
problem is the fact the timebase is frozen by the bringup of the
second CPU so the delays in the generic code will hang, we need
to move some of the calling procedure to inside the powermac code.
This makes it boot again for me
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The kernel reserves the I/O address space from 0x0 to 0xfff for legacy
ISA devices. Change the ranges property for the PCI2ISA bridge to match
the kernels behavior, even if the ranges property isn't used for now.
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A change to the i2c subsystem breaks the warp platform code. The patch
is cleaner anyway, the old way was a bit crufty.
For those with keen eyes, the gratuitous change in the string from
PIKA to Warp is just so the logs look a bit nicer. The following two
lines tend to be printed one after another.
Warp POST OK
Warp DTM thread running.
Yeah, this will be the third patch to warp.c submitted in this
release....
Cheers,
Sean
The i2c_client struct changed, breaking the code that looked for the ad7414
chip. Use the new of_find_i2c_device_by_node function added in 2.6.29.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Have git ignore generated files from dtc compile
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 31207dab7d
"Fix incorrect allocation of interrupt rev-map"
introduced a regression crashing on boot on machines using
a "DCR" based MPIC, such as the Cell blades.
The reason is that the irq host data structure is initialized
much later as a result of that patch, causing our calls to
mpic_map() do be done before we have a host setup.
Unfortunately, this breaks _mpic_map_dcr() which uses the
mpic->irqhost to get to the device node.
This fixes it by, instead, passing the device node explicitely
to mpic_map().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Akira Tsukamoto <akirat@rd.scei.sony.co.jp>
Turning on SWIOTLB selects or enables PPC_NEED_DMA_SYNC_OPS, which means
we get the non empty versions of dma_sync_* in asm/dma-mapping.h
On my pseries machine the dma_ops have no such routines and we die with
a null pointer - this patch gets it booting, is there a more elegant way
to do it?
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Update the mmap control page with the needed information to
use the userspace RDPMC instruction for self monitoring.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently, the following three different ways to define percpu arrays
are in use.
1. DEFINE_PER_CPU(elem_type[array_len], array_name);
2. DEFINE_PER_CPU(elem_type, array_name[array_len]);
3. DEFINE_PER_CPU(elem_type, array_name)[array_len];
Unify to #1 which correctly separates the roles of the two parameters
and thus allows more flexibility in the way percpu variables are
defined.
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: linux-mm@kvack.org
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: David S. Miller <davem@davemloft.net>
x86 throws away .discard section but no other archs do. Also,
.discard is not thrown away while linking modules. Make every arch
and module linking throw it away. This will be used to define dummy
variables for percpu declarations and definitions.
This patch is based on Ivan Kokshaysky's alpha percpu patch.
[ Impact: always throw away everything in .discard ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Bryan Wu <cooloney@kernel.org>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
This patch makes most !CONFIG_HAVE_SETUP_PER_CPU_AREA archs use
dynamic percpu allocator. The first chunk is allocated using
embedding helper and 8k is reserved for modules. This ensures that
the new allocator behaves almost identically to the original allocator
as long as static percpu variables are concerned, so it shouldn't
introduce much breakage.
s390 and alpha use custom SHIFT_PERCPU_PTR() to work around addressing
range limit the addressing model imposes. Unfortunately, this breaks
if the address is specified using a variable, so for now, the two
archs aren't converted.
The following architectures are affected by this change.
* sh
* arm
* cris
* mips
* sparc(32)
* blackfin
* avr32
* parisc (broken, under investigation)
* m32r
* powerpc(32)
As this change makes the dynamic allocator the default one,
CONFIG_HAVE_DYNAMIC_PER_CPU_AREA is replaced with its invert -
CONFIG_HAVE_LEGACY_PER_CPU_AREA, which is added to yet-to-be converted
archs. These archs implement their own setup_per_cpu_areas() and the
conversion is not trivial.
* powerpc(64)
* sparc(64)
* ia64
* alpha
* s390
Boot and batch alloc/free tests on x86_32 with debug code (x86_32
doesn't use default first chunk initialization). Compile tested on
sparc(32), powerpc(32), arm and alpha.
Kyle McMartin reported that this change breaks parisc. The problem is
still under investigation and he is okay with pushing this patch
forward and fixing parisc later.
[ Impact: use dynamic allocator for most archs w/o custom percpu setup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reviewed-by: Christoph Lameter <cl@linux.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Bryan Wu <cooloney@kernel.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
For yet unknown reason 4-bit mode doesn't work on MPC8569E-MDS boards,
so make 1-bit mode default. When we resolve the issue, u-boot will
remove sdhci,1-bit-only property from the device tree, while SDHCI
will still work with older u-boots.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
FSL RapidIO won't probe without a proper compatible entry. This
patch fixes the issue by adding fsl,rapidio-delta compatible to
mpc85xx_ids.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Match what other 85xx platforms do for of_platform_bus_probe and use
machine_device_initcall. This is one small step in killing of
ppc_md.init.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The qe_issue_cmd() function (Freescale PowerPC QUICC Engine library) polls
on a register until a status bit changes, but does not include a timeout
to handle the situation if the bit never changes. Change the code to use
the new spin_event_timeout() macro, which simplifies polling on a register
without a timeout.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (74 commits)
PCI: make msi_free_irqs() to use msix_mask_irq() instead of open coded write
PCI: Fix the NIU MSI-X problem in a better way
PCI ASPM: remove get_root_port_link
PCI ASPM: cleanup pcie_aspm_sanity_check
PCI ASPM: remove has_switch field
PCI ASPM: cleanup calc_Lx_latency
PCI ASPM: cleanup pcie_aspm_get_cap_device
PCI ASPM: cleanup clkpm checks
PCI ASPM: cleanup __pcie_aspm_check_state_one
PCI ASPM: cleanup initialization
PCI ASPM: cleanup change input argument of aspm functions
PCI ASPM: cleanup misc in struct pcie_link_state
PCI ASPM: cleanup clkpm state in struct pcie_link_state
PCI ASPM: cleanup latency field in struct pcie_link_state
PCI ASPM: cleanup aspm state field in struct pcie_link_state
PCI ASPM: fix typo in struct pcie_link_state
PCI: drivers/pci/slot.c should depend on CONFIG_SYSFS
PCI: remove redundant __msi_set_enable()
PCI PM: consistently use type bool for wake enable variable
x86/ACPI: Correct maximum allowed _CRS returned resources and warn if exceeded
...
This allows the callers to now pass down the full set of FAULT_FLAG_xyz
flags to handle_mm_fault(). All callers have been (mechanically)
converted to the new calling convention, there's almost certainly room
for architectures to clean up their code and then add FAULT_FLAG_RETRY
when that support is added.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (49 commits)
perfcounter: Handle some IO return values
perf_counter: Push perf_sample_data through the swcounter code
perf_counter tools: Define and use our own u64, s64 etc. definitions
perf_counter: Close race in perf_lock_task_context()
perf_counter, x86: Improve interactions with fast-gup
perf_counter: Simplify and fix task migration counting
perf_counter tools: Add a data file header
perf_counter: Update userspace callchain sampling uses
perf_counter: Make callchain samples extensible
perf report: Filter to parent set by default
perf_counter tools: Handle lost events
perf_counter: Add event overlow handling
fs: Provide empty .set_page_dirty() aop for anon inodes
perf_counter: tools: Makefile tweaks for 64-bit powerpc
perf_counter: powerpc: Add processor back-end for MPC7450 family
perf_counter: powerpc: Make powerpc perf_counter code safe for 32-bit kernels
perf_counter: powerpc: Change how processor-specific back-ends get selected
perf_counter: powerpc: Use unsigned long for register and constraint values
perf_counter: powerpc: Enable use of software counters on 32-bit powerpc
perf_counter tools: Add and use isprint()
...
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (24 commits)
tracing/urgent: warn in case of ftrace_start_up inbalance
tracing/urgent: fix unbalanced ftrace_start_up
function-graph: add stack frame test
function-graph: disable when both x86_32 and optimize for size are configured
ring-buffer: have benchmark test print to trace buffer
ring-buffer: do not grab locks in nmi
ring-buffer: add locks around rb_per_cpu_empty
ring-buffer: check for less than two in size allocation
ring-buffer: remove useless compile check for buffer_page size
ring-buffer: remove useless warn on check
ring-buffer: use BUF_PAGE_HDR_SIZE in calculating index
tracing: update sample event documentation
tracing/filters: fix race between filter setting and module unload
tracing/filters: free filter_string in destroy_preds()
ring-buffer: use commit counters for commit pointer accounting
ring-buffer: remove unused variable
ring-buffer: have benchmark test handle discarded events
ring-buffer: prevent adding write in discarded area
tracing/filters: strloc should be unsigned short
tracing/filters: operand can be negative
...
Fix up kmemcheck-induced conflict in kernel/trace/ring_buffer.c manually
This patch adds spi and mmc-spi-slot nodes, plus a gpio-controller for
PIXIS' sdcsr bank that is used for managing SPI chip-select and for
reading card's states.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In case gcc does something funny with the stack frames, or the return
from function code, we would like to detect that.
An arch may implement passing of a variable that is unique to the
function and can be saved on entering a function and can be tested
when exiting the function. Usually the frame pointer can be used for
this purpose.
This patch also implements this for x86. Where it passes in the stack
frame of the parent function, and will test that frame on exit.
There was a case in x86_32 with optimize for size (-Os) where, for a
few functions, gcc would align the stack frame and place a copy of the
return address into it. The function graph tracer modified the copy and
not the actual return address. On return from the funtion, it did not go
to the tracer hook, but returned to the parent. This broke the function
graph tracer, because the return of the parent (where gcc did not do
this funky manipulation) returned to the location that the child function
was suppose to. This caused strange kernel crashes.
This test detected the problem and pointed out where the issue was.
This modifies the parameters of one of the functions that the arch
specific code calls, so it includes changes to arch code to accommodate
the new prototype.
Note, I notice that the parsic arch implements its own push_return_trace.
This is now a generic function and the ftrace_push_return_trace should be
used instead. This patch does not touch that code.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Fix up the number of cells for the values of CPC925 Memory Controller,
and setup related platform device during system booting up, against
which CPC925 Memory Controller EDAC driver would be matched.
Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds support for the performance monitor hardware on the
MPC7450 family of processors (7450, 7451, 7455, 7447/7457, 7447A,
7448), used in the later Apple G4 powermacs/powerbooks and other
machines. These machines have 6 hardware counters with a unique
set of events which can be counted on each counter, with some
events being available on multiple counters.
Raw event codes for these processors are (PMC << 8) + PMCSEL.
If PMC is non-zero then the event is that selected by the given
PMCSEL value for that PMC (hardware counter). If PMC is zero
then the event selected is one of the low-numbered ones that are
common to several PMCs. In this case PMCSEL must be <= 22 and
the event is what that PMCSEL value would select on PMC1 (but
it may be placed any other PMC that has the same event for that
PMCSEL value).
For events that count cycles or occurrences that exceed a threshold,
the threshold requested can be specified in the 0x3f000 bits of the
raw event codes. If the event uses the threshold multiplier bit
and that bit should be set, that is indicated with the 0x40000 bit
of the raw event code.
This fills in some of the generic cache events. Unfortunately there
are quite a few blank spaces in the table, partly because these
processors tend to count cache hits rather than cache accesses.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: linuxppc-dev@ozlabs.org
Cc: benh@kernel.crashing.org
LKML-Reference: <19000.55631.802122.696927@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This abstracts a few things in arch/powerpc/kernel/perf_counter.c
that are specific to 64-bit kernels, and provides definitions for
32-bit kernels. In particular,
* Only 64-bit has MMCRA and the bits in it that give information
about a PMU interrupt (sampled PR, HV, slot number etc.)
* Only 64-bit has the lppaca and the lppaca->pmcregs_in_use field
* Use of SDAR is confined to 64-bit for now
* Only 64-bit has soft/lazy interrupt disable and therefore
pseudo-NMIs (interrupts that occur while interrupts are soft-disabled)
* Only 64-bit has PMC7 and PMC8
* Only 64-bit has the MSR_HV bit.
This also fixes the types used in a couple of places, where we were
using long types for things that need to be 64-bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: linuxppc-dev@ozlabs.org
Cc: benh@kernel.crashing.org
LKML-Reference: <19000.55590.634126.876084@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
At present, the powerpc generic (processor-independent) perf_counter
code has list of processor back-end modules, and at initialization,
it looks at the PVR (processor version register) and has a switch
statement to select a suitable processor-specific back-end.
This is going to become inconvenient as we add more processor-specific
back-ends, so this inverts the order: now each back-end checks whether
it applies to the current processor, and registers itself if so.
Furthermore, instead of looking at the PVR, back-ends now check the
cur_cpu_spec->oprofile_cpu_type string and match on that.
Lastly, each back-end now specifies a name for itself so the core can
print a nice message when a back-end registers itself.
This doesn't provide any support for unregistering back-ends, but that
wouldn't be hard to do and would allow back-ends to be modules.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: linuxppc-dev@ozlabs.org
Cc: benh@kernel.crashing.org
LKML-Reference: <19000.55529.762227.518531@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This changes the powerpc perf_counter back-end to use unsigned long
types for hardware register values and for the value/mask pairs used
in checking whether a given set of events fit within the hardware
constraints. This is in preparation for adding support for the PMU
on some 32-bit powerpc processors. On 32-bit processors the hardware
registers are only 32 bits wide, and the PMU structure is generally
simpler, so 32 bits should be ample for expressing the hardware
constraints. On 64-bit processors, unsigned long is 64 bits wide,
so using unsigned long vs. u64 (unsigned long long) makes no actual
difference.
This makes some other very minor changes: adjusting whitespace to line
things up in initialized structures, and simplifying some code in
hw_perf_disable().
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: linuxppc-dev@ozlabs.org
Cc: benh@kernel.crashing.org
LKML-Reference: <19000.55473.26174.331511@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This enables the perf_counter subsystem on 32-bit powerpc. Since we
don't have any support for hardware counters on 32-bit powerpc yet,
only software counters can be used.
Besides selecting HAVE_PERF_COUNTERS for 32-bit powerpc as well as
64-bit, the main thing this does is add an implementation of
set_perf_counter_pending(). This needs to arrange for
perf_counter_do_pending() to be called when interrupts are enabled.
Rather than add code to local_irq_restore as 64-bit does, the 32-bit
set_perf_counter_pending() generates an interrupt by setting the
decrementer to 1 so that a decrementer interrupt will become pending
in 1 or 2 timebase ticks (if a decrementer interrupt isn't already
pending). When interrupts are enabled, timer_interrupt() will be
called, and some new code in there calls perf_counter_do_pending().
We use a per-cpu array of flags to indicate whether we need to call
perf_counter_do_pending() or not.
This introduces a couple of new Kconfig symbols: PPC_HAVE_PMU_SUPPORT,
which is selected by processor families for which we have hardware PMU
support (currently only PPC64), and PPC_PERF_CTRS, which enables the
powerpc-specific perf_counter back-end.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: linuxppc-dev@ozlabs.org
Cc: benh@kernel.crashing.org
LKML-Reference: <19000.55404.103840.393470@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This function was only used by pci_claim_resource(), and the last commit
deleted that use.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch refactors clock.c by replacing printk calls with
pr_info/pr_cont, and uses '=' in output to connect key/value pairs
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
So far, MPC512x used mpc512x_find_ips_freq() to get the bus frequency,
while MPC52xx used mpc52xx_find_ipb_freq(). Despite the different
clock names (IPS vs. IPB) the code was identical.
Use common code for both processor families.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add a node for the i2c eeprom and delete the superflous gpio-example.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* akpm: (182 commits)
fbdev: bf54x-lq043fb: use kzalloc over kmalloc/memset
fbdev: *bfin*: fix __dev{init,exit} markings
fbdev: *bfin*: drop unnecessary calls to memset
fbdev: bfin-t350mcqb-fb: drop unused local variables
fbdev: blackfin has __raw I/O accessors, so use them in fb.h
fbdev: s1d13xxxfb: add accelerated bitblt functions
tcx: use standard fields for framebuffer physical address and length
fbdev: add support for handoff from firmware to hw framebuffers
intelfb: fix a bug when changing video timing
fbdev: use framebuffer_release() for freeing fb_info structures
radeon: P2G2CLK_ALWAYS_ONb tested twice, should 2nd be P2G2CLK_DAC_ALWAYS_ONb?
s3c-fb: CPUFREQ frequency scaling support
s3c-fb: fix resource releasing on error during probing
carminefb: fix possible access beyond end of carmine_modedb[]
acornfb: remove fb_mmap function
mb862xxfb: use CONFIG_OF instead of CONFIG_PPC_OF
mb862xxfb: restrict compliation of platform driver to PPC
Samsung SoC Framebuffer driver: add Alpha Channel support
atmel-lcdc: fix pixclock upper bound detection
offb: use framebuffer_alloc() to allocate fb_info struct
...
Manually fix up conflicts due to kmemcheck in mm/slab.c
Now we have __initconst, we can finally move the external declarations for
the various Linux logo structures to <linux/linux_logo.h>.
James' ack dates back to the previous submission (way to long ago), when the
logos were still __initdata, which caused failures on some platforms with some
toolchain versions.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: James Simmons <jsimmons@infradead.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Callers of alloc_pages_node() can optionally specify -1 as a node to mean
"allocate from the current node". However, a number of the callers in
fast paths know for a fact their node is valid. To avoid a comparison and
branch, this patch adds alloc_pages_exact_node() that only checks the nid
with VM_BUG_ON(). Callers that know their node is valid are then
converted.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Paul Mundt <lethal@linux-sh.org> [for the SLOB NUMA bits]
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* create mm/init-mm.c, move init_mm there
* remove INIT_MM, initialize init_mm with C99 initializer
* unexport init_mm on all arches:
init_mm is already unexported on x86.
One strange place is some OMAP driver (drivers/video/omap/) which
won't build modular, but it's already wants get_vm_area() export.
Somebody should look there.
[akpm@linux-foundation.org: add missing #includes]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Cc: Americo Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bastian Blank