The show_stack() function deals exclusively with kernel contexts, but if
it gets called in user context with EVA enabled, show_stacktrace() will
attempt to access the stack using EVA accesses, which will either read
other user mapped data, or more likely cause an exception which will be
handled by __get_user().
This is easily reproduced using SysRq t to show all task states, which
results in the following stack dump output:
Stack : (Bad stack address)
Fix by setting the current user access mode to kernel around the call to
show_stacktrace(). This causes __get_user() to use normal loads to read
the kernel stack.
Now we get the correct output, like this:
Stack : 00000000 80168960 00000000 004a0000 00000000 00000000 8060016c 1f3abd0c
1f172cd8 8056f09c 7ff1e450 8014fc3c 00000001 806dd0b0 0000001d 00000002
1f17c6a0 1f17c804 1f17c6a0 8066f6e0 00000000 0000000a 00000000 00000000
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000 00000000 00000000 00000000 0110e800 1f3abd6c 1f17c6a0
...
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 3.15+
Patchwork: https://patchwork.linux-mips.org/patch/10778/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If a machine check exception is raised in kernel mode, user context,
with EVA enabled, then the do_mcheck handler will attempt to read the
code around the EPC using EVA load instructions, i.e. as if the reads
were from user mode. This will either read random user data if the
process has anything mapped at the same address, or it will cause an
exception which is handled by __get_user, resulting in this output:
Code: (Bad address in epc)
Fix by setting the current user access mode to kernel if the saved
register context indicates the exception was taken in kernel mode. This
causes __get_user to use normal loads to read the kernel code.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 3.15+
Patchwork: https://patchwork.linux-mips.org/patch/10777/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The majority of SMP platforms handle their IPIs through do_IRQ()
which calls irq_{enter/exit}(). When a call function IPI is received,
smp_call_function_interrupt() is called which also calls
irq_{enter,exit}(), meaning irq_count is raised twice.
When tick broadcasting is used (which is implemented via a call
function IPI), this incorrectly causes all CPU idle time on the core
receiving broadcast ticks to be accounted as time spent servicing
IRQs, as account_process_tick() will account as such if irq_count is
greater than 1. This results in 100% CPU usage being reported on a
core which receives its ticks via broadcast.
This patch removes the SMP smp_call_function_interrupt() wrapper which
calls irq_{enter,exit}(). Platforms which handle their IPIs through
do_IRQ() now call generic_smp_call_function_interrupt() directly to
avoid incrementing irq_count a second time. Platforms which don't
(loongson, sgi-ip27, sibyte) call generic_smp_call_function_interrupt()
wrapped in irq_{enter,exit}().
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10770/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Execution of break instruction, trap instructions, emulation of unaligned
loads or floating point instructions - anything that tries to read the
instruction's opcode from userspace - needs read access to a page.
RIXI (Read Inhibit / Execute Inhibit) support however allows the creation of
pags that are executable but not readable. On such a mapping the attempted
load of the opcode by the kernel is going to cause an endless loop of
page faults.
The quick workaround for this is to disable the combinations that the kernel
currently isn't able to handle which are executable mappings.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On Malta, since commit a87ea88d8f ("MIPS: Malta: initialise the RTC at
boot"), the RTC is reinitialised and forced into binary coded decimal
(BCD) mode during init, even if the bootloader has already initialised
it, and may even have already put it into binary mode (as YAMON does).
This corrupts the current time, can result in the RTC seconds being an
invalid BCD (e.g. 0x1a..0x1f) for up to 6 seconds, as well as confusing
YAMON for a while after reset, enough for it to report timeouts when
attempting to load from TFTP (it actually uses the RTC in that code).
Therefore only initialise the RTC to the extent that is necessary so
that Linux avoids interfering with the bootloader setup, while also
allowing it to estimate the CPU frequency without hanging, without a
bootloader necessarily having done anything with the RTC (for example
when the kernel is loaded via EJTAG).
The divider control is configured for a 32KHZ reference clock if
necessary, and the SET bit of the RTC_CONTROL register is cleared if
necessary without changing any other bits (this bit will be set when
coming out of reset if the battery has been disconnected).
Fixes: a87ea88d8f ("MIPS: Malta: initialise the RTC at boot")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 3.14+
Patchwork: https://patchwork.linux-mips.org/patch/10739/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit eeb5389503 ("MIPS: unaligned: Prevent EVA instructions on kernel
unaligned accesses") renamed the Load* and Store* defines in unaligned.c
to _Load* and _Store* as part of its fix. One define was missed out which
causes big endian R6 kernels to fail to build.
arch/mips/kernel/unaligned.c:880:35:
error: implicit declaration of function '_StoreDW'
#define StoreDW(addr, value, res) _StoreDW(addr, value, res)
^
Signed-off-by: James Cowgill <James.Cowgill@imgtec.com>
Fixes: eeb5389503 ("MIPS: unaligned: Prevent EVA instructions on kernel unaligned accesses")
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: <stable@vger.kernel.org> # 4.0+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10575/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
p->thread.user_cpus_allowed is zero-initialized and is only filled on
the first sched_setaffinity call.
To avoid adding overhead in the task initialization codepath, simply OR
the returned mask in sched_getaffinity with p->cpus_allowed.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10740/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 01306aeadd ("MIPS: prepare for user enabling of CONFIG_OF")
changed the guards in asm/prom.h from CONFIG_OF to CONFIG_USE_OF, but
missed the actual function declarations in kernel/prom.c, which have
additional dependencies.
Fixes the following build error:
CC arch/mips/kernel/prom.o
arch/mips/kernel/prom.c: In function '__dt_setup_arch':
arch/mips/kernel/prom.c:54:2: error: implicit declaration of function 'early_init_dt_scan' [-Werror=implicit-function-declaration]
if (!early_init_dt_scan(bph))
^
Fixes: 01306aeadd ("MIPS: prepare for user enabling of CONFIG_OF")
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Rob Herring <robh@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: Grant Likely <grant.likely@linaro.org>
Patchwork: https://patchwork.linux-mips.org/patch/10741/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
71eeedcf51 (MIPS: Lemote 2F: Fix build caused
by recent mass rename.) only fixed one instance of this issue in arch/mips
but missed a 2nd one in drivers/cpufreq/loongson2_cpufreq.c.
[ralf@linux-mips.org: dropped the one segment for the already fixed
instance and changed the other avoiding an include <path.h> without a /
because that's generally is a bad idea.]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Patchwork: https://patchwork.linux-mips.org/patch/10659/
Ted Ts'o reports that his Lenovo T540p ThinkPad crashes at boot if
attached to the docking station. This is a regression that he was able
to bisect to commit 8c7b5ccb7298: "drm/i915: Use atomic helpers for
computing changed flags:"
The reason seems to be the new call to drm_atomic_helper_check_modeset()
added to intel_modeset_compute_config(), which in turn calls
update_connector_routing(), and somehow ends up picking a NULL crtc for
the connector state, causing the subsequent drm_crtc_index() to OOPS.
Daniel Vetter says that the fundamental issue seems to be confusion in
the encoder selection, and this isn't the right fix, but while he chases
down the proper fix, this at least avoids the NULL pointer dereference
and makes Ted's docking station work again.
Reported-bisected-and-tested-by: Theodore Ts'o <tytso@mit.edu>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Mani Nikula <jani.nikula@linux.intel.com>
Cc: Dave Airlie <airlied@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A set of three fixes for the ipr driver and one fairly major one for memory
leaks in the mq path of SCSI.
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJVvkKdAAoJEDeqqVYsXL0McOkH/3JRKdIqfI1vOWG5kje0f2DJ
qWwLZ68iG2t31Y8vdrSgT94/gfX3PH6rQ3yxuXDvr+oupTSoAyYR2D/R5zTOvusC
pKvYZSE74yUD23J6Www5WlkTZpSzbSknm7Hj6UkIkHW0+Ihk53pWfQReLbAWpY7h
MiMG7hqEnQEW2Wsp3SVD5jVy/tDyt2IeRZxcAqgBo5aU5xXzre0Kj8ya7hBZRCO0
cJaZjLPSJwapAzrqU2X7dOTCAojiMkDmHA4wGDmCtbdST6191JfOz8aiky7SJqnU
ii4kZLf2wPDUxmRYIJJnY8IweN+VMu7vAvCo2GbeJebpIgu8ZsjHd/9X/6XF0v4=
=oAZ+
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"A set of three fixes for the ipr driver and one fairly major one for
memory leaks in the mq path of SCSI"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: fix memory leak with scsi-mq
ipr: Fix invalid array indexing for HRRQ
ipr: Fix incorrect trace indexing
ipr: Fix locking for unit attention handling
Things are calming down nicely here w.r.t. fixes. This batch includes two
week's worth since I missed to send before -rc4.
Nothing particularly scary to point out, smaller fixes here and
there. Shortlog describes it pretty well.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVvcZ0AAoJEIwa5zzehBx3+dYQAKtl3XvLYKUurbwX5u79qgI5
66iLTdPkJxmdOArfKERbC4wstb39WcTjP3KRGHGpqWMxQZTZoAHZqx2itoU0CKyI
IzIu789SzmrwMDbGTOoU4OFeTxA3GNZBPdlxXbcilFqPALnvR9cT9HANc0nOaeOG
kwunJEKIZoVRDmeAd/u25Z//zRk4BYHcgRMfJRqpGEAIEXT2f+v4whLGjCa1pdPz
PpL6StHoXQ4raeocDhWAUkz/2HpjOFds1bhvaKmPb1zFissSSYBlS5QpCn110E3k
kpeu5lPojsVBkLPNqmyyx3vobj6pnDWuz2BdaZa8epqsV00hUnM+kIb+sfXnS24w
23gEAguT91Vw9hgFdVYc0R4xQwuQWqOmNgS6tkS96Aeie/bFBrPxB86AiA76fIaw
I/0aDJH2pQc6dMQFpzYK1hK3B4KSwlffKnfgIBUecLiXbWDwcTTwZH8Diwc25hdP
ozI9k6omUkiMTtyjLuj67/e7yTszxffLExPZlccu//kahhGSGJLhCQoRuRTBA0I6
bnAXC4hc7damn9Xj4RCM9PBXSWonraGyd6Mlgmr+h4MWZMANHuL4bwNcyQAx/gNq
muzSSFKak3zbo8zn/8j8l8W+UEPJap4pF01Et3HqeleAUx2j2ap7SKy+7eHn9P4F
D9EnzPopeZJpXJjf03qV
=AGL5
-----END PGP SIGNATURE-----
Merge tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Things are calming down nicely here w.r.t. fixes. This batch
includes two week's worth since I missed to send before -rc4.
Nothing particularly scary to point out, smaller fixes here and there.
Shortlog describes it pretty well"
* tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: keystone: fix dt bindings to use post div register for mainpll
ARM: nomadik: disable UART0 on Nomadik boards
ARM: dts: i.MX35: Fix can support.
ARM: OMAP2+: hwmod: Fix _wait_target_ready() for hwmods without sysc
ARM: dts: add CPU OPP and regulator supply property for exynos4210
ARM: dts: Update video-phy node with syscon phandle for exynos3250
ARM: DRA7: hwmod: fix gpmc hwmod
Pull VFS fix from Al Viro:
"Spurious ENOTDIR fix"
This should fix the problems reported by Dominique Martinet and Hugh
Dickins.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
link_path_walk(): be careful when failing with ENOTDIR
In RCU mode we might end up with dentry evicted just we check
that it's a directory. In such case we should return ECHILD
rather than ENOTDIR, so that pathwalk would be retries in non-RCU
mode.
Breakage had been introduced in commit b18825a - prior to that
we were looking at nd->inode, which had been fetched before
verifying that ->d_seq was still valid. That form of check
would only be satisfied if at some point the pathname prefix
would indeed have resolved to a non-directory. The fix consists
of checking ->d_seq after we'd run into a non-directory dentry,
and failing with ECHILD in case of mismatch.
Note that all branches since 3.12 have that problem...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
We had a regression due to reuse of descriptor so we have reverted that.
Rest are driver fixes
at_hdmac and at_xdmac for residue, trannfer width, and channel config
pl330 final fix for dma fails and overflow issue
xgene resouce map fix
mv_xor big endian op fix
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=X0jd
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fix-4.2-rc5' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"We had a regression due to reuse of descriptor so we have reverted
that.
The rest are driver fixes:
- at_hdmac and at_xdmac for residue, trannfer width, and channel config
- pl330 final fix for dma fails and overflow issue
- xgene resouce map fix
- mv_xor big endian op fix"
* tag 'dmaengine-fix-4.2-rc5' of git://git.infradead.org/users/vkoul/slave-dma:
Revert "dmaengine: virt-dma: don't always free descriptor upon completion"
dmaengine: mv_xor: fix big endian operation in register mode
dmaengine: xgene-dma: Fix the resource map to handle overlapping
dmaengine: at_xdmac: fix transfer data width in at_xdmac_prep_slave_sg()
dmaengine: at_hdmac: fix residue computation
dmaengine: at_xdmac: fix bug about channel configuration
dmaengine: pl330: Really fix choppy sound because of wrong residue calculation
dmaengine: pl330: Fix overflow when reporting residue in memcpy
Pull irq fixlets from Thomas Gleixner:
"Just two updates to the maintainers file"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
MAINTAINERS: Appoint Jiang and Marc as irqdomain maintainers
MAINTAINERS: Appoint Marc Zyngier as irqchips co-maintainer
Pull x86 fixes from Ingo Molnar:
"Fallout from the recent NMI fixes: make x86 LDT handling more robust.
Also some EFI fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/ldt: Make modify_ldt synchronous
x86/xen: Probe target addresses in set_aliased_prot() before the hypercall
x86/irq: Use the caller provided polarity setting in mp_check_pin_attr()
efi: Check for NULL efi kernel parameters
x86/efi: Use all 64 bit of efi_memmap in setup_e820()
Pull networking fixes from David Miller:
1) Must teardown SR-IOV before unregistering netdev in igb driver, from
Alex Williamson.
2) Fix ipv6 route unreachable crash in IPVS, from Alex Gartrell.
3) Default route selection in ipv4 should take the prefix length, table
ID, and TOS into account, from Julian Anastasov.
4) sch_plug must have a reset method in order to purge all buffered
packets when the qdisc is reset, likewise for sch_choke, from WANG
Cong.
5) Fix deadlock and races in slave_changelink/br_setport in bridging.
From Nikolay Aleksandrov.
6) mlx4 bug fixes (wrong index in port even propagation to VFs,
overzealous BUG_ON assertion, etc.) from Ido Shamay, Jack
Morgenstein, and Or Gerlitz.
7) Turn off klog message about SCTP userspace interface compat that
makes no sense at all, from Daniel Borkmann.
8) Fix unbounded restarts of inet frag eviction process, causing NMI
watchdog soft lockup messages, from Florian Westphal.
9) Suspend/resume fixes for r8152 from Hayes Wang.
10) Fix busy loop when MSG_WAITALL|MSG_PEEK is used in TCP recv, from
Sabrina Dubroca.
11) Fix performance regression when removing a lot of routes from the
ipv4 routing tables, from Alexander Duyck.
12) Fix device leak in AF_PACKET, from Lars Westerhoff.
13) AF_PACKET also has a header length comparison bug due to signedness,
from Alexander Drozdov.
14) Fix bug in EBPF tail call generation on x86, from Daniel Borkmann.
15) Memory leaks, TSO stats, watchdog timeout and other fixes to
thunderx driver from Sunil Goutham and Thanneeru Srinivasulu.
16) act_bpf can leak memory when replacing programs, from Daniel
Borkmann.
17) WOL packet fixes in gianfar driver, from Claudiu Manoil.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (79 commits)
stmmac: fix missing MODULE_LICENSE in stmmac_platform
gianfar: Enable device wakeup when appropriate
gianfar: Fix suspend/resume for wol magic packet
gianfar: Fix warning when CONFIG_PM off
act_pedit: check binding before calling tcf_hash_release()
net: sk_clone_lock() should only do get_net() if the parent is not a kernel socket
net: sched: fix refcount imbalance in actions
r8152: reset device when tx timeout
r8152: add pre_reset and post_reset
qlcnic: Fix corruption while copying
act_bpf: fix memory leaks when replacing bpf programs
net: thunderx: Fix for crash while BGX teardown
net: thunderx: Add PCI driver shutdown routine
net: thunderx: Fix crash when changing rss with mutliple traffic flows
net: thunderx: Set watchdog timeout value
net: thunderx: Wakeup TXQ only if CQE_TX are processed
net: thunderx: Suppress alloc_pages() failure warnings
net: thunderx: Fix TSO packet statistic
net: thunderx: Fix memory leak when changing queue count
net: thunderx: Fix RQ_DROP miscalculation
...
Pull btrfs fixes from Chris Mason:
"Filipe fixed up a hard to trigger ENOSPC regression from our merge
window pull, and we have a few other smaller fixes"
* 'for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix quick exhaustion of the system array in the superblock
btrfs: its btrfs_err() instead of btrfs_error()
btrfs: Avoid NULL pointer dereference of free_extent_buffer when read_tree_block() fail
btrfs: Fix lockdep warning of btrfs_run_delayed_iputs()
This became a relative big update as it includes the collected
ASoC fixes. There are a few fixes in ASoC core side, mostly for DAPM
and the new topology API. The rest are various ASoC driver-specific
fixes, as well as the usual HD-audio and USB-audio quirks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=blL8
-----END PGP SIGNATURE-----
Merge tag 'sound-4.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This became a relative big update as it includes the collected ASoC
fixes. There are a few fixes in ASoC core side, mostly for DAPM and
the new topology API. The rest are various ASoC driver-specific
fixes, as well as the usual HD-audio and USB-audio quirks"
* tag 'sound-4.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (29 commits)
ALSA: hda - Fix MacBook Pro 5,2 quirk
ALSA: hda - Fix race between PM ops and HDA init/probe
ALSA: usb-audio: add dB range mapping for some devices
ALSA: hda - Apply a fixup to Dell Vostro 5480
ALSA: hda - Add pin quirk for the headset mic jack detection on Dell laptop
ALSA: hda - Apply fixup for another Toshiba Satellite S50D
ALSA: fireworks: add support for AudioFire2 quirk
ALSA: hda - Fix the headset mic that will not work on Dell desktop machine
ALSA: hda - fix cs4210_spdif_automute()
ASoC: pcm1681: Fix setting de-emphasis sampling rate selection
ASoC: ssm4567: Keep TDM_BCLKS in ssm4567_set_dai_fmt
ASoC: sgtl5000: Fix up define for SGTL5000_SMALL_POP
ASoC: dapm: Don't add prefix to widget stream name
ASoC: rt5645: Check if codec is initialized in workqueue handler
ASoC: Intel: Get correct usage_count value to load firmware
ASoC: topology: Fix to add dapm mixer info
ASoC: zx: spdif: Fix devm_ioremap_resource return value check
ASoC: zx: i2s: Fix devm_ioremap_resource return value check
ASoC: mediatek: Use platform_of_node for machine drivers
ASoC: Free card DAPM context on snd_soc_instantiate_card() error path
...
Commit 50649ab149 ("stmmac: drop driver from stmmac platform code")
was a bit overzealous in removing code and dropped the MODULE_*
macro's that are still needed since stmmac_platform can be a module.
Fix this by putting the macro's remvoed in 50649ab149 back.
This fixes the following errors when used as a module:
stmmac_platform: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint
stmmac_platform: Unknown symbol devm_kmalloc (err 0)
stmmac_platform: Unknown symbol stmmac_suspend (err 0)
stmmac_platform: Unknown symbol platform_get_irq_byname (err 0)
stmmac_platform: Unknown symbol stmmac_dvr_remove (err 0)
stmmac_platform: Unknown symbol platform_get_resource (err 0)
stmmac_platform: Unknown symbol of_get_phy_mode (err 0)
stmmac_platform: Unknown symbol of_property_read_u32_array (err 0)
stmmac_platform: Unknown symbol of_alias_get_id (err 0)
stmmac_platform: Unknown symbol stmmac_resume (err 0)
stmmac_platform: Unknown symbol stmmac_dvr_probe (err 0)
Fixes: 50649ab149 ("stmmac: drop driver from stmmac platform code")
Reported-by: Igor Gnatenko <i.gnatenko.brain@gmail.com>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Claudiu Manoil says:
====================
gianfar: wol magic packet fixes
These changes were already validated as part of FSL SDK.
Patch 2 fixes occasional wake-on magic packet failures during
traffic, probably due to incorrect traffic stop/ device halt
sequence and incorrect usage of txlock.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The wol_en flag is 0 by default anyway, and we have the
following inconsistency: a MAGIC packet wol capable eth
interface is registered as a wake-up source but unable
to wake-up the system as wol_en is 0 (wake-on flag set to 'd').
Calling set_wakeup_enable() at netdev open is just redundant
because wol_en is 0 by default.
Let only ethtool call set_wakeup_enable() for now.
The bflock is obviously obsoleted, its utility has been corroded
over time. The bitfield flags used today in gianfar are accessed
only on the init/ config path, with no real possibility of
concurrency - nothing that would justify smth. like bflock.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we disable NAPI in the first place we can mask the device's
interrupts (and halt it) without fearing that imask may be
concurrently accessed from interrupt context, so there's
no need to do local_irq_save() around gfar_halt_nodisable().
lock_rx_qs()/unlock_tx_qs() are just obsoleted and potentially
buggy routines. The txlock is currently used in the driver only
to manage TX congestion, it has nothing to do with halting the
device. With these changes, the TX processing is stopped before
gfar_halt().
Compact gfar_halt() is used instead of gfar_halt_nodisable(),
as it disables Rx/TX DMA h/w blocks and the Rx/TX h/w queues.
gfar_start() re-enables all these blocks on resume. Enabling
the magic-packet mode remains the same, note that the RX block
is re-enabled just before entering sleep mode.
Add IRQF_NO_SUSPEND flag for the error interrupt line, to signal
that the interrupt line must remain active during sleep in order
to wake the system by magic packet (MAG) reception interrupt.
(On some systems the MAG interrupt did trigger w/o this flag
as well, but on others it didn't.)
Without these fixes, when suspended during fair Tx traffic the
interface occasionally failed to be woken up by magic packet.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC drivers/net/ethernet/freescale/gianfar.o
drivers/net/ethernet/freescale/gianfar.c:568:13: warning: 'lock_tx_qs'
defined but not used [-Wunused-function]
static void lock_tx_qs(struct gfar_private *priv)
^
drivers/net/ethernet/freescale/gianfar.c:576:13: warning: 'unlock_tx_qs'
defined but not used [-Wunused-function]
static void unlock_tx_qs(struct gfar_private *priv)
^
Reported-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we share an action within a filter, the bind refcnt
should increase, therefore we should not call tcf_hash_release().
Fixes: 1a29321ed0 ("net_sched: act: Dont increment refcnt on replace")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
All of the keystone devices have a separate register to hold post
divider value for main pll clock. Currently the fixed-postdiv
value used for k2hk/l/e SoCs works by sheer luck as u-boot happens to
use a value of 2 for this. Now that we have fixed this in the pll
clock driver change the dt bindings for the same.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
These fixes are all for the AMD IOMMU driver:
* A regression with HSA caused by the conversion of the driver to
default domains. The fixes make sure that an HSA device can
still be attached to an IOMMUv2 domain and that these domains
also allow non-IOMMUv2 capable devices.
* Fix iommu=pt mode which did not work because the dma_ops where
set to nommu_ops, which breaks devices that can only do 32bit
DMA.
* Fix an issue with non-PCI devices not working, because there
are no dma_ops for them. This issue was discovered recently as
new AMD x86 platforms have non-PCI devices too.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=amGQ
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"These fixes are all for the AMD IOMMU driver:
- A regression with HSA caused by the conversion of the driver to
default domains. The fixes make sure that an HSA device can still
be attached to an IOMMUv2 domain and that these domains also allow
non-IOMMUv2 capable devices.
- Fix iommu=pt mode which did not work because the dma_ops where set
to nommu_ops, which breaks devices that can only do 32bit DMA.
- Fix an issue with non-PCI devices not working, because there are no
dma_ops for them. This issue was discovered recently as new AMD
x86 platforms have non-PCI devices too"
* tag 'iommu-fixes-v4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Allow non-ATS devices in IOMMUv2 domains
iommu/amd: Set global dma_ops if swiotlb is disabled
iommu/amd: Use swiotlb in passthrough mode
iommu/amd: Allow non-IOMMUv2 devices in IOMMUv2 domains
iommu/amd: Use iommu core for passthrough mode
iommu/amd: Use iommu_attach_group()
Pull drm intel fixes from Daniel Vetter:
"I delayed my -fixes pull a bit hoping that I could include a fix for
the dp mst stuff but looks a bit more nasty than that. So just 3
other regression fixes, one 4.2 other two cc: stable"
* tag 'drm-intel-fixes-2015-07-31' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Declare the swizzling unknown for L-shaped configurations
drm/i915: Mark PIN_USER binding as GLOBAL_BIND without the aliasing ppgtt
drm/i915: Replace WARN inside I915_READ64_2x32 with retry loop
Pull drm fixes from Dave Airlie:
"This has a bunch of nouveau fixes, as Ben has been hibernating and has
lots of small fixes for lots of bugs across nouveau.
Radeon has one major fix for hdmi/dp audio regression that is larger
than Alex would like, but seems to fix up a fair few bugs, along with
some misc fixes.
And a few msm fixes, one of which is also a bit large.
But nothing in here seems insane or crazy for this stage, just more
than I'd like"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (33 commits)
drm/msm/mdp5: release SMB (shared memory blocks) in various cases
drm/msm: change to uninterruptible wait in atomic commit
drm/msm: mdp4: Fix drm_framebuffer dereference crash
drm/msm: fix msm_gem_prime_get_sg_table()
drm/amdgpu: add new parameter to seperate map and unmap
drm/amdgpu: hdp_flush is not needed for inside IB
drm/amdgpu: different emit_ib for gfx and compute
drm/amdgpu: information leak in amdgpu_info_ioctl()
drm/amdgpu: clean up init sequence for failures
drm/radeon/combios: add some validation of lvds values
drm/radeon: rework audio modeset to handle non-audio hdmi features
drm/radeon: rework audio detect (v4)
drm/amdgpu: Drop drm/ prefix for including drm.h in amdgpu_drm.h
drm/radeon: Drop drm/ prefix for including drm.h in radeon_drm.h
drm/nouveau/nouveau/ttm: fix tiled system memory with Maxwell
drm/nouveau/kms/nv50-: guard against enabling cursor on disabled heads
drm/nouveau/fbcon/g80: reduce PUSH_SPACE alloc, fire ring on accel init
drm/nouveau/fbcon/gf100-: reduce RING_SPACE allocation
drm/nouveau/fbcon/nv11-: correctly account for ring space usage
drm/nouveau/bios: add proper support for opcode 0x59
...
This reverts commit b9855f03d5.
The patch break existing DMA usage case. For example, audio SOC
dmaengine never release channel and cause virt-dma to cache too
much memory in descriptor to exhaust system memory.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit 6f166312c6 ("dmaengine: mv_xor: add support for a38x command
in descriptor mode") introduced the support for a feature that
appeared in Armada 38x: specifying the operation to be performed in a
per-descriptor basis rather than globally per channel.
However, when doing so, it changed the function mv_chan_set_mode() to
use:
if (IS_ENABLED(__BIG_ENDIAN))
instead of:
#if defined(__BIG_ENDIAN)
While IS_ENABLED() is perfectly fine for CONFIG_* symbols, it is not
for other symbols such as __BIG_ENDIAN that is provided directly by
the compiler. Consequently, the commit broke support for big-endian,
as the XOR_DESCRIPTOR_SWAP flag was not set in the XOR channel
configuration register.
The primarily visible effect was some nasty warnings and failures
appearing during the self-test of the XOR unit:
[ 1.197368] mv_xor d0060900.xor: error on chan 0. intr cause 0x00000082
[ 1.197393] mv_xor d0060900.xor: config 0x00008440
[ 1.197410] mv_xor d0060900.xor: activation 0x00000000
[ 1.197427] mv_xor d0060900.xor: intr cause 0x00000082
[ 1.197443] mv_xor d0060900.xor: intr mask 0x000003f7
[ 1.197460] mv_xor d0060900.xor: error cause 0x00000000
[ 1.197477] mv_xor d0060900.xor: error addr 0x00000000
[ 1.197491] ------------[ cut here ]------------
[ 1.197513] WARNING: CPU: 0 PID: 1 at ../drivers/dma/mv_xor.c:664 mv_xor_interrupt_handler+0x14c/0x170()
See also:
http://storage.kernelci.org/next/next-20150617/arm-mvebu_v7_defconfig+CONFIG_CPU_BIG_ENDIAN=y/lab-khilman/boot-armada-xp-openblocks-ax3-4.txt
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Fixes: 6f166312c6 ("dmaengine: mv_xor: add support for a38x command in descriptor mode")
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is an overlap in dma ring cmd csr region due to sharing of ethernet
ring cmd csr region. This patch fix the resource overlapping by mapping
the entire dma ring cmd csr region.
Signed-off-by: Rameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds the missing update of the transfer data width in
at_xdmac_prep_slave_sg().
Indeed, for each item in the scatter-gather list, we check whether the
transfer length is aligned with the data width provided by
dmaengine_slave_config(). If so, we directly use this data width for the
current part of the transfer we are preparing. Otherwise, the data width
is reduced to 8 bits (1 byte). Of course, the actual number of register
accesses must also be updated to match the new data width.
So one chunk was missing in the original patch (see Fixes tag below): the
number of register accesses was correctly set to (len >> fixed_dwidth) in
mbr_ubc but the real data width was not updated in mbr_cfg. Since mbr_cfg
may change for each part of the scatter-gather transfer this also explains
why the original patch used the Descriptor View 2 instead of the
Descriptor View 1.
Let's take the example of a DMA transfer to write 8bit data into an Atmel
USART with FIFOs. When FIFOs are enabled in the USART, its Transmit
Holding Register (THR) works in multidata mode, that is to say that up to
4 8bit data can be written into the THR in a single 32bit access and it is
still possible to write only one data with a 8bit access. To take
advantage of this new feature, the DMA driver was modified to allow
multiple dwidths when doing slave transfers.
For instance, when the total length is 22 bytes, the USART driver splits
the transfer into 2 parts:
First part: 20 bytes transferred through 5 32bit writes into THR
Second part: 2 bytes transferred though 2 8bit writes into THR
For the second part, the data width was first set to 4_BYTES by the USART
driver thanks to dmaengine_slave_config() then at_xdmac_prep_slave_sg()
reduces this data width to 1_BYTE because the 2 byte length is not aligned
with the original 4_BYTES data width. Since the data width is modified,
the actual number of writes into THR must be set accordingly.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Fixes: 6d3a7d9e3a ("dmaengine: at_xdmac: allow muliple dwidths when doing slave transfers")
Cc: stable@vger.kernel.org #4.0 and later
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As claimed by the programmer datasheet and confirmed by the IP designer,
the Block Transfer Size (BTSIZE) bitfield of the Channel x Control A
Register (CTRLAx) always refers to a number of Source Width (SRC_WIDTH)
transfers.
Both the SRC_WIDTH and BTSIZE bitfields can be extacted from the CTRLAx
register to compute the DMA residue. So the 'tx_width' field is useless
and can be removed from the struct at_desc.
Before this patch, atc_prep_slave_sg() was not consistent: BTSIZE was
correctly initialized according to the SRC_WIDTH but 'tx_width' was always
set to reg_width, which was incorrect for MEM_TO_DEV transfers. It led to
bad DMA residue when 'tx_width' != SRC_WIDTH.
Also the 'tx_width' field was mostly set only in the first and last
descriptors. Depending on the kind of DMA transfer, this field remained
uninitialized for intermediate descriptors. The accurate DMA residue was
computed only when the currently processed descriptor was the first or the
last of the chain. This algorithm was a little bit odd. An accurate DMA
residue can always be computed using the SRC_WIDTH and BTSIZE bitfields
in the CTRLAx register.
Finally, the test to check whether the currently processed descriptor is
the last of the chain was wrong: for cyclic transfer, last_desc->lli.dscr
is NOT equal to zero, since set_desc_eol() is never called, but logically
equal to first_desc->txd.phys. This bug has a side effect on the
drivers/tty/serial/atmel_serial.c driver, which uses cyclic DMA transfer
to receive data. Since the DMA residue was wrong each time the DMA
transfer reaches the second (and last) period of the transfer, no more
data were received by the USART driver till the cyclic DMA transfer loops
back to the first period.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Torsten Fleischer <torfl6749@gmail.com>
Tested-by: Jirí Prchal <jiri.prchal@aksignal.cz>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When using descriptor view 2 or higher, we don't write the configuration
into AT_XDMAC_CC register because this configuration will be fetch from
the descriptor. Unfortunately, the PROT bit is not updated with this
method, we have to do it manually before enabling the channel.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
With the grouping of multi-function devices a non-ATS
capable device might also end up in the same domain as an
IOMMUv2 capable device.
So handle this situation gracefully and don't consider it a
bug anymore.
Tested-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
modify_ldt() has questionable locking and does not synchronize
threads. Improve it: redesign the locking and synchronize all
threads' LDTs using an IPI on all modifications.
This will dramatically slow down modify_ldt in multithreaded
programs, but there shouldn't be any multithreaded programs that
care about modify_ldt's performance in the first place.
This fixes some fallout from the CVE-2015-5157 fixes.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Andrew Cooper <andrew.cooper3@citrix.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jan Beulich <jbeulich@suse.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: security@kernel.org <security@kernel.org>
Cc: <stable@vger.kernel.org>
Cc: xen-devel <xen-devel@lists.xen.org>
Link: http://lkml.kernel.org/r/4c6978476782160600471bd865b318db34c7b628.1438291540.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The update_va_mapping hypercall can fail if the VA isn't present
in the guest's page tables. Under certain loads, this can
result in an OOPS when the target address is in unpopulated vmap
space.
While we're at it, add comments to help explain what's going on.
This isn't a great long-term fix. This code should probably be
changed to use something like set_memory_ro.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andrew Cooper <andrew.cooper3@citrix.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: David Vrabel <dvrabel@cantab.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jan Beulich <jbeulich@suse.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: security@kernel.org <security@kernel.org>
Cc: <stable@vger.kernel.org>
Cc: xen-devel <xen-devel@lists.xen.org>
Link: http://lkml.kernel.org/r/0b0e55b995cda11e7829f140b833ef932fcabe3a.1438291540.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
booting because the upper 32-bits of the EFI memmap pointer were
being discarded in setup_e820() - Dmitry Skorodumov
* Validate that the "efi" kernel parameter gets used with an argument,
otherwise we will oops - Ricardo Neri
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=kohF
-----END PGP SIGNATURE-----
Merge tag 'efi-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into x86/urgent
Pull EFI fixes from Matt Fleming:
* Fix an EFI boot issue preventing a Parallels virtual machine from
booting because the upper 32-bits of the EFI memmap pointer were
being discarded in setup_e820(). (Dmitry Skorodumov)
* Validate that the "efi" kernel parameter gets used with an argument,
otherwise we will oops. (Ricardo Neri)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
- remote attribute log recovery corruption fixes
- DAX page faults need to use direct mappings, not a page cache
mapping.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=kjas
-----END PGP SIGNATURE-----
Merge tag 'xfs-for-linus-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
Pull xfs fixes from Dave Chinner:
"There are a couple of recently found, long standing remote attribute
corruption fixes caused by log recovery getting confused after a
crash, and the new DAX code in XFS (merged in 4.2-rc1) needs to
actually use the DAX fault path on read faults.
Summary:
- remote attribute log recovery corruption fixes
- DAX page faults need to use direct mappings, not a page cache
mapping"
* tag 'xfs-for-linus-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs:
xfs: remote attributes need to be considered data
xfs: remote attribute headers contain an invalid LSN
xfs: call dax_fault on read page faults for DAX
The newsk returned by sk_clone_lock should hold a get_net()
reference if, and only if, the parent is not a kernel socket
(making this similar to sk_alloc()).
E.g,. for the SYN_RECV path, tcp_v4_syn_recv_sock->..inet_csk_clone_lock
sets up the syn_recv newsk from sk_clone_lock. When the parent (listen)
socket is a kernel socket (defined in sk_alloc() as having
sk_net_refcnt == 0), then the newsk should also have a 0 sk_net_refcnt
and should not hold a get_net() reference.
Fixes: 26abe14379 ("net: Modify sk_alloc to not reference count the
netns of kernel sockets.")
Acked-by: Eric Dumazet <edumazet@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 55334a5db5 ("net_sched: act: refuse to remove bound action
outside"), we end up with a wrong reference count for a tc action.
Test case 1:
FOO="1,6 0 0 4294967295,"
BAR="1,6 0 0 4294967294,"
tc filter add dev foo parent 1: bpf bytecode "$FOO" flowid 1:1 \
action bpf bytecode "$FOO"
tc actions show action bpf
action order 0: bpf bytecode '1,6 0 0 4294967295' default-action pipe
index 1 ref 1 bind 1
tc actions replace action bpf bytecode "$BAR" index 1
tc actions show action bpf
action order 0: bpf bytecode '1,6 0 0 4294967294' default-action pipe
index 1 ref 2 bind 1
tc actions replace action bpf bytecode "$FOO" index 1
tc actions show action bpf
action order 0: bpf bytecode '1,6 0 0 4294967295' default-action pipe
index 1 ref 3 bind 1
Test case 2:
FOO="1,6 0 0 4294967295,"
tc filter add dev foo parent 1: bpf bytecode "$FOO" flowid 1:1 action ok
tc actions show action gact
action order 0: gact action pass
random type none pass val 0
index 1 ref 1 bind 1
tc actions add action drop index 1
RTNETLINK answers: File exists [...]
tc actions show action gact
action order 0: gact action pass
random type none pass val 0
index 1 ref 2 bind 1
tc actions add action drop index 1
RTNETLINK answers: File exists [...]
tc actions show action gact
action order 0: gact action pass
random type none pass val 0
index 1 ref 3 bind 1
What happens is that in tcf_hash_check(), we check tcf_common for a given
index and increase tcfc_refcnt and conditionally tcfc_bindcnt when we've
found an existing action. Now there are the following cases:
1) We do a late binding of an action. In that case, we leave the
tcfc_refcnt/tcfc_bindcnt increased and are done with the ->init()
handler. This is correctly handeled.
2) We replace the given action, or we try to add one without replacing
and find out that the action at a specific index already exists
(thus, we go out with error in that case).
In case of 2), we have to undo the reference count increase from
tcf_hash_check() in the tcf_hash_check() function. Currently, we fail to
do so because of the 'tcfc_bindcnt > 0' check which bails out early with
an -EPERM error.
Now, while commit 55334a5db5 prevents 'tc actions del action ...' on an
already classifier-bound action to drop the reference count (which could
then become negative, wrap around etc), this restriction only accounts for
invocations outside a specific action's ->init() handler.
One possible solution would be to add a flag thus we possibly trigger
the -EPERM ony in situations where it is indeed relevant.
After the patch, above test cases have correct reference count again.
Fixes: 55334a5db5 ("net_sched: act: refuse to remove bound action outside")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hayes Wang says:
====================
r8152: device reset
v3:
For patch #2, remove cancel_delayed_work().
v2:
For patch #1, remove usb_autopm_get_interface(), usb_autopm_put_interface(), and
the checking of intf->condition.
For patch #2, replace the original method with usb_queue_reset_device() to reset
the device.
v1:
Although the driver works normally, we find the device may get all 0xff data when
transmitting packets on certain platforms. It would break the device and no packet
could be transmitted. The reset is necessary to recover the hw for this situation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The device reset is necessary if the hw becomes abnormal and stops
transmitting packets.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rtl8152_pre_reset() and rtl8152_post_reset() which are used when
calling usb_reset_device(). The two functions could reduce the time
of reset when calling usb_reset_device() after probe().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MacBook Pro 5,2 with ALC889 codec had already a fixup entry, but this
seems not working correctly, a fix for pin NID 0x15 is needed in
addition. It's equivalent with the fixup for MacBook Air 1,1, so use
this instead.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=102131
Reported-and-tested-by: Jeffery Miller <jefferym@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
James Hogan