Currently, if the norm set is V4L2_STD_ALL, then autodetect the current
standard and use that. This is non-standard behavior, and in fact it hasn't
worked for a very long time: before s_std is called in this driver, the
v4l2 core will mask it with the tvnorms field. So even if the application
passes V4L2_STD_ALL, the zoran driver will always see a subset of that.
Since nobody ever complained about this we just remove this non-standard
functionality.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
AND the standard mask with the detected standards.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since this driver properly implements g_std, the current_norm field is
actually unused anyway.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The use of current_norm can be dropped. The g_std ioctl was already
implemented, so current_norm didn't do anything useful anyway.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
current_norm is deprecated. Replace it by g_std.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ensure that the register is aligned to a dword, otherwise the range check
could fail since it assumes dword alignment.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ensure that the register is aligned to a dword, otherwise the range check
could fail since it assumes dword alignment.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This op and the v4l2-chip-ident.h header are no longer needed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace g_chip_ident by g_chip_info. Note that the IR support is implemented
as a subdev, so this part no longer needs to be handled as a 'bridge' chip.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
g_chip_ident was used to determine if a saa7114 or saa7115 was used. Instead
just check the subdev name.
After that the g_chip_ident function can be removed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The av-core is really a subdev, so there is no need anymore to act as if it
is a 'second' bridge chip.
As a result of this the g_chip_ident implementation can be completely dropped.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_DBG_G_CHIP_IDENT has been replaced by VIDIOC_DBG_G_CHIP_INFO. Remove
g_chip_ident support from bridge drivers since it is no longer needed.
This patch takes care of all the trivial cases.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes a NULL pointer deference when loading the cx88_dvb module for a
Hauppauge HVR4000.
The bugzilla bug report is here:
https://bugzilla.kernel.org/show_bug.cgi?id=56271
The cause is that the wm8775 is optional, so even though the board info says
there is one, it doesn't have to be there. Checking whether the module was
actually loaded is much safer.
Note that this driver is quite buggy when it comes to unloading and reloading
modules. Unloading cx8800 and reloading it again will still cause a crash,
most likely because either the i2c bus isn't unloaded at the right time and/or
the v4l2_device_unregister isn't called at the right time.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Sebastian Frei <sebastian@familie-frei.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
worse, we lock ->resource_lock too late when we are destroying the
final clonal VMA; the check for lack of other mappings of the same
opened file can race with mmap().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This patch removes check for EPERM in dbg_g/s_register and
vidioc_g/s_register as this check is already performed by core.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The orig code will release all the resources if v4l2_device_register()
failed and return 0. But what we need in this case is to return an
negative error code to let the caller known we are failed.
So the patch save the return value of v4l2_device_register() to 'ret'
and return it when error.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As the enum values have changed recently, the comments are void.
Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add CyberVision CV06 4-camera card (from CyberVision SV card kit):
http://www.cybervision.com.tw/products-swcard_kits-sv.html
There are some interesting things on the card but they're not supported:
4 LEDs, a connector with 4 IN and 4 OUT pins, RESET IN and RESET OUT
connectors, a relay and CyberVision CV8088-SV16 chip
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for noname Bt848 capture-only card (3x composite, 1x S-VHS)
with 14MHz crystal:
http://www.rainbow-software.org/images/hardware/bt848_.jpg
14MHz PLL was not supported by bttv driver until now.
[mchehab@redhat.com: CodingStyle fixes]
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a proper card entry for this device, rather than abusing entries that are
not-quite-right.
Regards,
Hans
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull i2c changes from Wolfram Sang:
- an arbitration driver. While the driver is quite simple, it caused
discussion if we need additional arbitration on top of the one
specified in the I2C standard. Conclusion is that I accept a few
generic mechanisms, but not very specific ones.
- the core lost the detach_adapter() call. It has no users anymore and
was in the way for other cleanups. attach_adapter() is sadly still
there since there are users waiting to be converted.
- the core gained a bus recovery infrastructure. I2C defines a way to
recover if the data line is stalled. This mechanism is now in the
core and drivers can now pass some data to make use of it.
- bigger driver cleanups for designware, s3c2410
- removing superfluous refcounting from drivers
- removing Ben Dooks as second maintainer due to inactivity. Thanks
for all your work so far, Ben!
- bugfixes, feature additions, devicetree fixups, simplifications...
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
i2c: xiic: must always write 16-bit words to TX_FIFO
i2c: octeon: use HZ in timeout value
i2c: octeon: Fix i2c fail problem when a process is terminated by a signal
i2c: designware-pci: drop superfluous {get|put}_device
i2c: designware-plat: drop superfluous {get|put}_device
i2c: davinci: drop superfluous {get|put}_device
MAINTAINERS: Ben Dooks is inactive regarding I2C
i2c: mux: Add i2c-arb-gpio-challenge 'mux' driver
i2c: at91: convert to dma_request_slave_channel_compat()
i2c: mxs: do error checking and handling in PIO mode
i2c: mxs: remove races in PIO code
i2c-designware: switch to use runtime PM autosuspend
i2c-designware: use usleep_range() in the busy-loop
i2c-designware: enable/disable the controller properly
i2c-designware: use dynamic adapter numbering on Lynxpoint
i2c-designware-pci: use managed functions pcim_* and devm_*
i2c-designware-pci: use dev_err() instead of printk()
i2c-designware: move to managed functions (devm_*)
i2c: remove CONFIG_HOTPLUG ifdefs
i2c: s3c2410: Add SMBus emulation for block read
...
Pull VFS updates from Al Viro,
Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).
7kloc removed.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
don't bother with deferred freeing of fdtables
proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
proc: Make the PROC_I() and PDE() macros internal to procfs
proc: Supply a function to remove a proc entry by PDE
take cgroup_open() and cpuset_open() to fs/proc/base.c
ppc: Clean up scanlog
ppc: Clean up rtas_flash driver somewhat
hostap: proc: Use remove_proc_subtree()
drm: proc: Use remove_proc_subtree()
drm: proc: Use minor->index to label things, not PDE->name
drm: Constify drm_proc_list[]
zoran: Don't print proc_dir_entry data in debug
reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
proc: Supply an accessor for getting the data from a PDE's parent
airo: Use remove_proc_subtree()
rtl8192u: Don't need to save device proc dir PDE
rtl8187se: Use a dir under /proc/net/r8180/
proc: Add proc_mkdir_data()
proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
proc: Move PDE_NET() to fs/proc/proc_net.c
...
Don't print proc_dir_entry data in debug as we're soon to have no direct
access to the contents of the PDE. Print what was put in there instead.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: mjpeg-users@lists.sourceforge.net
cc: linux-media@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull media update from Mauro Carvalho Chehab:
- OF documentation and patches at core and drivers, to be used by for
embedded media systems
- some I2C drivers used on go7007 were rewritten/promoted from staging:
sony-btf-mpx, tw2804, tw9903, tw9906, wis-ov7640, wis-uda1342
- add fimc-is driver (Exynos)
- add a new radio driver: radio-si476x
- add a two new tuners: r820t and tuner_it913x
- split camera code on em28xx driver and add more models
- the cypress firmware load is used outside dvb usb drivers. So, move
it to a common directory to make easier to re-use it
- siano media driver updated to work with sms2270 devices
- several work done in order to promote go7007 and solo6x1x out of
staging (still, there are some pending issues)
- several API compliance fixes at v4l2 drivers that don't behave as
expected
- as usual, lots of driver fixes, improvements, cleanups and new device
addition at the existing drivers.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (831 commits)
[media] cx88: make core less verbose
[media] em28xx: fix oops at em28xx_dvb_bus_ctrl()
[media] s5c73m3: fix indentation of the help section in Kconfig
[media] cx25821-alsa: get rid of a __must_check warning
[media] cx25821-video: declare cx25821_vidioc_s_std as static
[media] cx25821-video: remove maxw from cx25821_vidioc_try_fmt_vid_cap
[media] r820t: Remove a warning for an unused value
[media] dib0090: Fix a warning at dib0090_set_EFUSE
[media] dib8000: fix a warning
[media] dib8000: Fix sub-channel range
[media] dib8000: store dtv_property_cache in a temp var
[media] dib8000: warning fix: declare internal functions as static
[media] r820t: quiet gcc warning on n_ring
[media] r820t: memory leak in release()
[media] r820t: precendence bug in r820t_xtal_check()
[media] videodev2.h: Remove the unused old V4L1 buffer types
[media] anysee: Grammar s/report the/report to/
[media] anysee: Initialize ret = 0 in anysee_frontend_attach()
[media] media: videobuf2: fix the length check for mmap
[media] em28xx: save isoc endpoint number for DVB only if endpoint has alt settings with xMaxPacketSize != 0
...
Along the time, several debug messages were added at cx88-cards.
While those are still useful to track some troubles with
tuners, they're too verbose:
[ 5768.281801] cx88[0]: Calling XC2028/3028 callback
[ 5768.287388] cx88[0]: Calling XC2028/3028 callback
[ 5768.292575] cx88[0]: Calling XC2028/3028 callback
[ 5768.299408] cx88[0]: Calling XC2028/3028 callback
[ 5768.306244] cx88[0]: Calling XC2028/3028 callback
...
and, most of the time, useless.
So, disable them, except if core_debug modprobe parameter
is used.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The hole reason for __must_check is to not ignore an error.
However, a "ret" value is used at cx25821 just to avoid the
Kernel compilation to compain about it.
That, however, produces another warning (with W=1):
drivers/media/pci/cx25821/cx25821-alsa.c: In function 'cx25821_audio_fini':
drivers/media/pci/cx25821/cx25821-alsa.c:727:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
With the current implementation of driver_for_each_device() and
cx25821_alsa_exit_callback(), there's actually just one
very unlikely condition where it will currently produce
an error: if driver_find() returns NULL.
Ok, there's not much that can be done, as it is on a driver's
function that returns void, but it can at least print some message
if the error happens.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes the following warning:
drivers/media/pci/cx25821/cx25821-video.c: At top level:
drivers/media/pci/cx25821/cx25821-video.c:766:5: warning: no previous prototype for 'cx25821_vidioc_s_std' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After cx25821-video cleanup, this var is not used anymore:
drivers/media/pci/cx25821/cx25821-video.c: In function 'cx25821_vidioc_try_fmt_vid_cap':
drivers/media/pci/cx25821/cx25821-video.c:591:15: warning: variable 'maxw' set but not used [-Wunused-but-set-variable]
as the code now checks the max width as the default case for the
range check.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Legacy PCI suspend-resume handlers are called with interrupts enabled.
But cx8800_suspend/cx8800_resume and
cx8802_suspend_common/cx8802_resume_common use spin_lock/spin_unlock
functions to acquire dev->slock, while the same lock is acquired in the
corresponding irq-handlers: cx8800_irq and cx8802_irq.
That means a deadlock is possible if an interrupt happens while suspend
or resume owns the lock. The patch replaces spin_lock/spin_unlock with
spin_lock_irqsave/spin_unlock_irqrestore.
Found by Linux Driver Verification project (linuxtesting.org).
[mchehab@redhat.com: Fix CodingStyle]
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
From Fengguang Wu <fengguang.wu@intel.com>:
> drivers/media/pci/sta2x11/sta2x11_vip.c: In function 'sta2x11_vip_init_one':
> drivers/media/pci/sta2x11/sta2x11_vip.c:1314:2: error: implicit declaration of function 'i2c_get_adapter' [-Werror=implicit-function-declaration]
> drivers/media/pci/sta2x11/sta2x11_vip.c:1314:15: warning: assignment makes pointer from integer without a cast [enabled by default]
> drivers/media/pci/sta2x11/sta2x11_vip.c:1330:2: error: implicit declaration of function 'i2c_put_adapter' [-Werror=implicit-function-declaration]
And also:
> warning: (STA2X11_VIP) selects VIDEO_ADV7180 which has unmet direct dependencies (MEDIA_SUPPORT && VIDEO_V4L2 && I2C)
> drivers/media/i2c/adv7180.c: In function '__adv7180_status':
> drivers/media/i2c/adv7180.c:194:2: error: implicit declaration of function 'i2c_smbus_read_byte_data' [-Werror=implicit-function-declaration]
> drivers/media/i2c/adv7180.c: In function 'adv7180_s_routing':
> drivers/media/i2c/adv7180.c:251:2: error: implicit declaration of function 'i2c_smbus_write_byte_data' [-Werror=implicit-function-declaration]
> drivers/media/i2c/adv7180.c: In function 'adv7180_probe':
> drivers/media/i2c/adv7180.c:551:2: error: implicit declaration of function 'i2c_check_functionality' [-Werror=implicit-function-declaration]
> drivers/media/i2c/adv7180.c:554:2: error: implicit declaration of function 'i2c_adapter_id' [-Werror=implicit-function-declaration]
> drivers/media/i2c/adv7180.c: At top level:
> drivers/media/i2c/adv7180.c:663:1: warning: data definition has no type or storage class [enabled by default]
> drivers/media/i2c/adv7180.c:663:1: warning: type defaults to 'int' in declaration of 'module_i2c_driver' [-Wimplicit-int]
> drivers/media/i2c/adv7180.c:663:1: warning: parameter names (without types) in function declaration [enabled by default]
> drivers/media/i2c/adv7180.c:649:26: warning: 'adv7180_driver' defined but not used [-Wunused-variable]
This is due to the lack of I2C support:
...
> CONFIG_I2C is not set
...
So, Make sure that sta2x11_vip depends on I2C.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Don't print proc_dir_entry data in debug as we're soon to have no direct
access to the contents of the PDE. Print what was put in there instead.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The audio output is currently not used as this should be rewritten as an
alsa driver. For the time being remove this source from the Makefile.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ideally this should be implemented with vb2, but it'll do for now.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx25821-video-upstream_ch2.c/h is practically identical to cx25821-video-upstream.c/h
so add support for ch2 into cx25821-video-upstream.c instead.
After this we can replace the custom ioctls with a proper write() interface.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
No other changes, just function reordering.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drop the custom ioctls and enable the video output nodes again, this time
using standard ioctls.
The next step will be to provide a proper write() interface.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver does not have subdevices, so why call subdev ops? After
removing that it became apparent that only Composite is supported as
input, so remove also any reference to other inputs.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
No idea why these custom ioctls exist: they have perfectly normal v4l2
counterparts which are already implemented.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- fill in colorspace
- zero priv
- delete unsupported formats
- fix field handling
- s_std should update width/height
- proper mapping of width/height to valid resolutions
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is now possible to remove cx25821_fh and replace it with v4l2_fh,
which in turn makes event handling and core prio handling possible.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Just remember which filehandle is streaming instead of using complicated
resource masks.
After this patch we can replace cx25821_fh with v4l2_fh.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is not a per-filehandle object, it's a per-channel object.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This allows us to replace .ioctl with .unlocked_ioctl.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l2 core already has support for debugging ioctls/file operations.
No need to do that again.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Embed the video_device struct instead of allocating it.
Remove some of the annoying and ugly kernel messages shown during
loading and unloading of the module.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver doesn't use DVB, RC, cx25840 or tveeprom.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver does not implement cropping, so remove the cropping ioctls.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A lot of functions and variables were external when they really can be
declared as static.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The s_input implementation allowed input 1 even if that didn't exist.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This device list is not necessary. The kernel already has all that information,
so just use that instead.
Also remove a bogus refcount and some dead 'private_free' code in the alsa driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
And get rid of the channel0-11 external pointers and two more unused fields
in cx25821.h.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
log_status shouldn't print LOG STATUS lines, the core does that already.
Fix querycap version number and add device_caps support.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do some spring cleaning:
- there are no board defines with tuners, so remove bogus tuner support.
- tv standard handling has nothing to do with tuners, so keep that.
- replace the deprecated current_norm by g_std.
- querystd isn't implemented, so remove the ioctl.
- remove a bunch of unused fields in cx25821.h
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This device does not support radio or vbi, so remove anything referring
to that.
In addition, the driver created an 'video ioctl' node, which was unused and
was effectively identical to the first video node.
This bogus video node is now removed, leaving us with 8 video capture nodes
and 2 video output nodes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/pci/cx25821/cx25821-video.c: In function ‘cx25821_video_register’:
drivers/media/pci/cx25821/cx25821-video.c:518:1: warning: the frame size of 1600 bytes is larger than 1024 bytes [-Wframe-larger-than=]
Fixed by just making the struct video_device template static const.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Skip the audio channel when registering the video nodes. This fixes a bug
where that incorrectly registered 'video' node was never unregistered.
Note: this bug only surfaces if the video output nodes are enabled again
after the previous patch disabled them.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx25821 driver has support for one audio output channel and two video
output channels.
This is implemented in a very ugly and very evil way through a custom ioctl
that passes the filename of a file containing the video data, which is then
read by the driver itself using vfs.
There are a number of problems with this:
1) it's very ugly and very evil (I can't say that often enough).
2) V4L2 supports video output, so why not use that?
3) it's very buggy, closing the filehandle through which you passed the ioctl
will oops the kernel.
4) it's a nasty security leak since this allows you to load any file in the
system as a video or audio source, so in theory you can output /etc/passwd
to audio or video out and record & decode it on another device.
Because of all these issues we no longer register those output video nodes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx25821 driver has support for one audio output channel and two video
output channels.
This is implemented in a very ugly and very evil way through a custom ioctl
that passes the filename of a file containing the video data, which is then
read by the driver itself using vfs.
There are a number of problems with this:
1) it's very ugly and very evil (I can't say that often enough).
2) V4L2 supports video output, so why not use that?
3) it's very buggy, closing the filehandle through which you passed the ioctl
will oops the kernel.
4) it's a nasty security leak since this allows you to load any file in the
system as a video or audio source, so in theory you can output /etc/passwd
to audio or video out and record & decode it on another device.
Because of all these issues we no longer register those output video nodes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make saa7134 driver more V4L2 compliant: clear reserved space of VBI
structure to make sure no garbage is left there
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make saa7134 driver more V4L2 compliant: remove empty g_parm function
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make saa7134 driver more V4L2 compliant: remove empty g_audio and s_audio
functions and don't set audioset in enum_input
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make saa7134 driver more V4L2 compliant: return real frequency range in
g_tuner and fail in s_tuner for non-zero tuner
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make saa7134 driver more V4L2 compliant: don't cache frequency in
s_frequency/g_frequency but return real one instead
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make saa7134 driver more V4L2 compliant: remove broken priority handling
and use v4l2_fh instead
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
[hans.verkuil@cisco.com: fixed a merge conflict in saa7134.h]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make saa7134 driver more V4L2 compliant: filter audio modes that came from
tuner - keep only MONO/STEREO in radio mode
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make saa7134 driver more V4L2 compliant: implement V4L2_CAP_DEVICE_CAPS support
and fix all capabilities problems reported by v4l2-compliance.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The only part of proc_dir_entry the code outside of fs/proc
really cares about is PDE(inode)->data. Provide a helper
for that; static inline for now, eventually will be moved
to fs/proc, along with the knowledge of struct proc_dir_entry
layout.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Use enum instead of magic values for LNA config in tda8290.
Update tda827x, tda18271 and saa7134 to use the enum too.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add AverMedia AverTV Satellite Hybrid+FM (A706) card to saa7134 driver.
Working: analog inputs, TV, FM radio and IR remote control.
Untested: DVB-S.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
config looks like a hack that was added to tuner-core to allow some
configuration of TDA8290 tuner (it's not used by any other driver).
But with the new configuration options of tda8290 driver (no_i2c_gate
and std_map), it's no longer sufficient.
Change config to be void * instead, which allows passing tuner-dependent
config struct to drivers.
Also update saa7134 driver to reflect this change (no other driver uses this).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hauppauge Nova-S-Plus DVB-S model 92001 does not lock on horizontal
polarisation. According with the info provided at the BZ, model
92002 does.
The difference is that, on model 92001, the tone select is done via
isl6421, while, on other devices, this is done via cx24123 code.
This patch adds a way to override the demod's set_tone at isl6421
driver. In order to avoid regressions, the override is enabled
only for cx88 Nova S plus model 92001. For all other models and
devices, the set_tone is provided by the demod driver.
Patch originally proposed at bz@9476[1] by Michel Meyers and
John Donoghue but applying the original patch would break support
for all other devices based on isl6421.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=9476
Tested-by: Adam Sampson <ats@offog.org>
Tested-by: Hans-Peter Jansen <hpj@urpla.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
"enum dmx_ts_pes" and "typedef enum dmx_pes_type_t" are just the
same enum declared twice, since Kernel (2.6.12). There's no reason
to duplicate it there, and sparse complains about that:
drivers/media/dvb-core/dmxdev.c:600:55: warning: mixing different enum types
So, remove the internal define, keeping just the external one.
Internally, use only "enum dmx_ts_pes", as it is too late to drop
dmx_pes_type_t from the userspace API.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
i2c_del_adapter() always returns 0. So all checks testing whether it will be
non zero will always evaluate to false and the conditional code is dead code.
This patch updates all callers of i2c_del_mux_adapter() to ignore the return
value and assume that it will always succeed (which it will). In a subsequent
patch the return type of i2c_del_adapter() will be made void.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRWLTrAAoJEHm+PkMAQRiGe8oH/iMy48mecVWvxVZn74Tx3Cef
xmW/PnAIj28EhSPqK49N/Ow6AfQToFKf7AP0ge20KAf5teTq95AY+tH74DAANt8F
BjKXXTZiR5xwBvRkq7CR5wDcCvEcBAAz8fgTEd6SEDB2d2VXFf5eKdKUqt1avTCh
Z6Hup5kuwX+ddtwY2DCBXtp2n6fL0Rm5yLzY1A3OOBye1E7VyLTF7M5BR603Q44P
4kRLxn8+R7jy3hTuZIhAeoS8TKUoBwVk7DmKxEzrhTHZVOmvwE9lEHybRnIyOpd/
k1JnbRbiPsLsCVFOn10SQkGDAIk00lro3tuWP2C1ljERiD/OOh5Ui9nXYAhMkbI=
=q15K
-----END PGP SIGNATURE-----
Merge tag 'v3.9-rc5' into patchwork
Linux 3.9-rc5
* tag 'v3.9-rc5': (1080 commits)
Linux 3.9-rc5
Revert "lockdep: check that no locks held at freeze time"
dw_dmac: adjust slave_id accordingly to request line base
dmaengine: dw_dma: fix endianess for DT xlate function
PNP: List Rafael Wysocki as a maintainer
rbd: don't zero-fill non-image object requests
ia64 idle: delete stale (*idle)() function pointer
Btrfs: don't drop path when printing out tree errors in scrub
target: Fix RESERVATION_CONFLICT status regression for iscsi-target special case
tcm_vhost: Avoid VIRTIO_RING_F_EVENT_IDX feature bit
Revert "mm: introduce VM_POPULATE flag to better deal with racy userspace programs"
usb: ftdi_sio: Add support for Mitsubishi FX-USB-AW/-BD
mg_disk: fix error return code in mg_probe()
Btrfs: fix wrong return value of btrfs_lookup_csum()
Btrfs: fix wrong reservation of csums
Btrfs: fix double free in the btrfs_qgroup_account_ref()
Btrfs: limit the global reserve to 512mb
Btrfs: hold the ordered operations mutex when waiting on ordered extents
Btrfs: fix space accounting for unlink and rename
Btrfs: fix space leak when we fail to reserve metadata space
...
Since commit a1fd287780c8e91fed4957b30c757b0c93021162:
"[media] bttv-driver: fix two warnings"
cropcap.defrect.height and cropcap.bounds.height for the PAL entry are 32
resp 30 pixels too large, if a userspace app (ie xawtv) actually tries to use
the full advertised height, the resulting image is broken in ways only a
screenshot can describe.
The cause of this is the fix for this warning:
drivers/media/pci/bt8xx/bttv-driver.c:308:3: warning: initialized field overwritten [-Woverride-init]
In this chunk of the commit:
@@ -301,11 +301,10 @@ const struct bttv_tvnorm bttv_tvnorms[] = {
/* totalwidth */ 1135,
/* sqwidth */ 944,
/* vdelay */ 0x20,
- /* sheight */ 576,
- /* videostart0 */ 23)
/* bt878 (and bt848?) can capture another
line below active video. */
- .cropcap.bounds.height = (576 + 2) + 0x20 - 2,
+ /* sheight */ (576 + 2) + 0x20 - 2,
+ /* videostart0 */ 23)
},{
.v4l2_id = V4L2_STD_NTSC_M | V4L2_STD_NTSC_M_KR,
.name = "NTSC",
Which replaces the overriding of cropcap.bounds.height initialization outside
of the CROPCAP macro (which also initializes it), with passing a
different sheight value to the CROPCAP macro.
There are 2 problems with this warning fix:
1) The sheight value is used twice in the CROPCAP macro, and the old code
only changed one resulting value.
2) The old code increased the .cropcap.bounds.height value (and did not
touch the .cropcap.defrect.height value at all) by 2, where as the fixed
code increases it by 32, as the fixed code passes (576 + 2) + 0x20 - 2
to the CROPCAP macro, but the + 0x20 - 2 is already done by the macro so
now is done twice for .cropcap.bounds.height, and also is applied to
.cropcap.defrect.height where it should not be applied at all.
This patch fixes this by adding an extraheight parameter to the CROPCAP entry
and using it for the PAL entry.
Cc: stable@kernel.org # For Kernel 3.8
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl is defined as IOW, so pass the argument as const.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ivtv_itvc function receives a pointer to v4l2_dbg_register. When we
add const to that pointer in the s_register case we will run into a problem
here since this common function would discard const in that case. So
change this function so it receives the address and a pointer to a value.
In addition we now set the size field in the g_register function which is
where it belongs.
This will simplify the next patch where const will be added to s_register.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl is defined as IOW, so pass the argument by value instead of by
reference. I could have chosen to add const instead, but this is 1) easier
to handle in drivers and 2) consistent with the s_std subdev operation.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl is defined as IOW, so pass the argument as const.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl is defined as IOW, so pass the argument as const.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Previously, this has been done implicitly for video device nodes by calling
set_input() (which calls audio_input() and also modified the mute
setting).
Since input and mute setting are now untangled (as much as possible), we need to
apply the mute setting with an explicit call to audio_mute().
Also apply the mute setting when the radio device node gets opened.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Split function audio_mux():
move the mute setting part to function audio_mute() and the input setting part
to function audio_input().
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the GPIO part of function audio_mux() to a separate function
audio_mux_gpio().
This prepares the code for the next patch which will separate mute and input
setting.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
'audio_input' better describes the meaning of this field.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We can't and do not save the mute setting in function audio_mux(), so we
should also not save the input in this function for consistency.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are cases where we want to call audio_mux() without changing the value of
the v4l2 mute control, for example
- mute mute on last close
- mute on device probing
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Function audio_mux() actually deals with two types of mute: gpio mute and
subdevice muting.
This patch claryfies the meaning of these values, but mainly prepares the code for
the next patch.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I'm pasting the original code and my proposal on the commit message for
make it easy to compare the two versions.
Line 62 of cx25821-audio-upstream.h contains:
char *_defaultAudioName = "/root/audioGOOD.wav";
Original code after replace kmemdup for kstrdup, and after fix return error
code:
if (dev->input_audiofilename) {
dev->_audiofilename = kstrdup(dev->input_audiofilename,
GFP_KERNEL);
if (!dev->_audiofilename) {
err = -ENOMEM;
goto error;
}
/* Default if filename is empty string */
if (strcmp(dev->input_audiofilename, "") == 0)
dev->_audiofilename = "/root/audioGOOD.wav";
} else {
dev->_audiofilename = kstrdup(_defaultAudioName,
GFP_KERNEL);
if (!dev->_audiofilename) {
err = -ENOMEM;
goto error;
}
}
Code proposed in this patch:
if ((dev->input_audiofilename) &&
(strcmp(dev->input_audiofilename, "") != 0))
dev->_audiofilename = kstrdup(dev->input_audiofilename,
GFP_KERNEL);
else
dev->_audiofilename = kstrdup(_defaultAudioName,
GFP_KERNEL);
if (!dev->_audiofilename) {
err = -ENOMEM;
goto error;
}
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Like init_bttv_i2c(), fini_bttv_i2c() belongs to bttv-i2c.c.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Request module ir-kbd-i2c if an i2c ir decoder is detected.
Tested with device "Hauppauge WinTV Theatre" (model 37284 rev B421).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note that the current driver does not implement enumaudio (so apps cannot
tell that audio inputs are present), it does not set V4L2_CAP_AUDIO, nor
does it set audioset when calling ENUM_INPUT. And G_AUDIO doesn't set the
stereo flag either. So these g/s_audio ioctls are quite pointless and
misleading. Especially since some surveillance boards do not have audio
at all.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Just opening the radio tuner should not cause a switch to the radio tuner.
Only after calling g/s_tuner or g/s_frequency should this happen.
This prevents audio being unmuted as soon as the driver is loaded because
some process opens /dev/radioX just to see what sort of node it is, which
switches on the radio tuner and unmutes audio.
This code can be improved further by actually keeping track of who owns the
tuner and returning -EBUSY if switching tuner modes will cause problems.
But for now just fix the annoying case where on boot the radio turns on
automatically.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
try_fmt_vid_overlay should map incorrect sizes and fields to valid values.
It also expects that an initial overlay size is defined so g_fmt_vid_overlay
returns valid information.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The capability field of v4l2_tuner should be ORed by the various subdevs
and by the main driver. In this case the stereo capability was dropped.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Probe for additional tvaudio devices, and allow tvaudio+tda7432 to
co-exist. My STB TV PCI FM bttv card has a tda7432, a tda9850 and a
tea6420 and with this patch it finally works again (probably for the
first time in many years).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The 'current_norm' field cannot be used if multiple device nodes (video and
vbi in this case) set the same std.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note that the private chroma agc control has been replaced with the standard
CHROMA_AGC control.
Also fixes a mute/automute problem where closing the file handle would force
mute on. That's not what you want since that would make the mute state out of
sync with the mute control. Instead check against the user count.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- don't return -EINVAL for invalid field types, handle those as if it
was FIELD_ANY.
- the handling of FIELD_SEQ_BT/TB was wrong as well: if such field formats
aren't supported, then fall back to FIELD_ANY instead of returning an error.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set an initial frequencies when the driver is loaded. That way G_FREQUENCY will
give a frequency that corresponds with reality.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If no tuner is present, then disable the tuner and frequency ioctls.
We can remove a number of checks from those ioctls testing for the presence
of a tuner.
Also remove some tuner type checks (now done by the core) and fix an
error return when the prio check fails.
Finally some 'unlikely' statements are removed since those only make sense
in tightly often executed loops, otherwise they just clutter up the code.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_DBG_G_CHIP_IDENT is a prerequisite for the G/S_REGISTER ioctls.
In addition, add support to call G/S_REGISTER for supporting i2c devices.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The querycap ioctl didn't support V4L2_CAP_DEVICE_CAPS and the radio device
implemented audio and video inputs and s_std, which are not part of the radio
API.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull vfs pile (part one) from Al Viro:
"Assorted stuff - cleaning namei.c up a bit, fixing ->d_name/->d_parent
locking violations, etc.
The most visible changes here are death of FS_REVAL_DOT (replaced with
"has ->d_weak_revalidate()") and a new helper getting from struct file
to inode. Some bits of preparation to xattr method interface changes.
Misc patches by various people sent this cycle *and* ocfs2 fixes from
several cycles ago that should've been upstream right then.
PS: the next vfs pile will be xattr stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
saner proc_get_inode() calling conventions
proc: avoid extra pde_put() in proc_fill_super()
fs: change return values from -EACCES to -EPERM
fs/exec.c: make bprm_mm_init() static
ocfs2/dlm: use GFP_ATOMIC inside a spin_lock
ocfs2: fix possible use-after-free with AIO
ocfs2: Fix oops in ocfs2_fast_symlink_readpage() code path
get_empty_filp()/alloc_file() leave both ->f_pos and ->f_version zero
target: writev() on single-element vector is pointless
export kernel_write(), convert open-coded instances
fs: encode_fh: return FILEID_INVALID if invalid fid_type
kill f_vfsmnt
vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op
nfsd: handle vfs_getattr errors in acl protocol
switch vfs_getattr() to struct path
default SET_PERSONALITY() in linux/elf.h
ceph: prepopulate inodes only when request is aborted
d_hash_and_lookup(): export, switch open-coded instances
9p: switch v9fs_set_create_acl() to inode+fid, do it before d_instantiate()
9p: split dropping the acls from v9fs_set_create_acl()
...
Pull media updates from Mauro Carvalho Chehab:
- Some cleanups at V4L2 documentation
- new drivers: ts2020 frontend, ov9650 sensor, s5c73m3 sensor,
sh-mobile veu mem2mem driver, radio-ma901, davinci_vpfe staging
driver
- Lots of missing MAINTAINERS entries added
- several em28xx driver improvements, including its conversion to
videobuf2
- several fixups on drivers to make them to better comply with the API
- DVB core: add support for DVBv5 stats, allowing the implementation of
statistics for new standards like ISDB
- mb86a20s: add statistics to the driver
- lots of new board additions, cleanups, and driver improvements.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (596 commits)
[media] media: Add 0x3009 USB PID to ttusb2 driver (fixed diff)
[media] rtl28xxu: Add USB IDs for Compro VideoMate U620F
[media] em28xx: add usb id for terratec h5 rev. 3
[media] media: rc: gpio-ir-recv: add support for device tree parsing
[media] mceusb: move check earlier to make smatch happy
[media] radio-si470x doc: add info about v4l2-ctl and sox+alsa
[media] staging: media: Remove unnecessary OOM messages
[media] sh_vou: Use vou_dev instead of vou_file wherever possible
[media] sh_vou: Use video_drvdata()
[media] drivers/media/platform/soc_camera/pxa_camera.c: use devm_ functions
[media] mt9t112: mt9t111 format set up differs from mt9t112
[media] sh-mobile-ceu-camera: fix SHARPNESS control default
Revert "[media] fc0011: Return early, if the frequency is already tuned"
[media] cx18/ivtv: fix regression: remove __init from a non-init function
[media] em28xx: fix analog streaming with USB bulk transfers
[media] stv0900: remove unnecessary null pointer check
[media] fc0011: Return early, if the frequency is already tuned
[media] fc0011: Add some sanity checks and cleanups
[media] fc0011: Fix xin value clamping
Revert "[media] [PATH,1/2] mxl5007 move reset to attach"
...
Commits 5e6e81b289 (cx18) and
2aebbf6737 (ivtv) added an __init
annotation to the cx18-alsa-load and ivtv-alsa-load functions. However,
these functions are called *after* initialization by the main cx18/ivtv
driver. By that time the memory containing those functions is already
freed and your machine goes BOOM.
Cc: stable@vger.kernel.org # for 3.8
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The btcx-risc module is a helper module for bttv/conexant based TV cards.
It isn't an i2c module at all, instead it should be in common since it is
used by 4 pci drivers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds new capture board Hawell HW-9004V1. This card has 4 SAA71300 chips. In order to work it is needed to initialize its registers (gpio mask and value). The value of these registers were dumped under Windows using flytest.
Signed-off-by: Vadim Frolov <fralik@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch re-write the driver and use the videobuf2
interface instead of the old videobuf. Moreover, it uses also
the control framework which allows the driver to inherit
controls from its subdevice (ADV7180). Finally the driver does not
implement custom file operation but it uses the generic ones from
videobuf2 and v4l2_fh
Signed-off-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch introduces the use of IS_ENABLED() macro. For example,
replacing:
#if defined(CONFIG_I2C) || (defined(CONFIG_I2C_MODULE) && defined(MODULE))
with:
#if IS_ENABLED(CONFIG_I2C)
All changes made by this patch respect the same replacement pattern.
Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change several memcpy() to memmove() in cases when the regions are
definitely overlapping; memcpy() of overlapping regions is undefined
behavior in C and can produce different results depending on the compiler,
the memcpy implementation, etc.
Cc: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Nickolai Zeldovich <nickolai@csail.mit.edu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The idx values passed to cx18_i2c_register() and ivtv_i2c_register()
by cx18_init_subdevs() and ivtv_load_and_init_modules() respectively
are always in-range, based on how the hw_all bitmask is populated.
Previously, the checks were already ineffective because arrays were
being dereferenced using the index before the check.
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Nickolai Zeldovich <nickolai@csail.mit.edu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert the meye driver to the control framework. Some private controls
have been replaced with standardized controls (SHARPNESS and JPEGQUAL).
The AGC control looks like it can be replaced by the AUTOGAIN control, but
it isn't a boolean so I do not know how to interpret it.
The FRAMERATE control looks like it can be replaced by S_PARM, but again,
without knowing how to interpret it I decided to leave it alone.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Compiling the saa7164 driver without CONFIG_VIDEO_ADV_DEBUG set triggers
these GCC warnings:
drivers/media/pci/saa7164/saa7164-encoder.c:1301:12: warning: ‘saa7164_g_register’ defined but not used [-Wunused-function]
drivers/media/pci/saa7164/saa7164-encoder.c:1314:12: warning: ‘saa7164_s_register’ defined but not used [-Wunused-function]
Silence these warnings by wrapping these two functions in an "#ifdef
CONFIG_VIDEO_ADV_DEBUG" and "#endif" pair.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* v4l_for_linus: (464 commits)
[media] uvcvideo: Set error_idx properly for S_EXT_CTRLS failures
[media] uvcvideo: Cleanup leftovers of partial revert
[media] uvcvideo: Return -EACCES when trying to set a read-only control
Linux 3.8-rc3
mm: reinstante dropped pmd_trans_splitting() check
cred: Remove tgcred pointer from struct cred
drm/ttm: fix fence locking in ttm_buffer_object_transfer
ARM: clps711x: Fix bad merge of clockevents setup
ARM: highbank: save and restore L2 cache and GIC on suspend
ARM: highbank: add a power request clear
ARM: highbank: fix secondary boot and hotplug
ARM: highbank: fix typos with hignbank in power request functions
ARM: dts: fix highbank cpu mpidr values
ARM: dts: add device_type prop to cpu nodes on Calxeda platforms
drm/prime: drop reference on imported dma-buf come from gem
xen/netfront: improve truesize tracking
ARM: mx5: Fix MX53 flexcan2 clock
ARM: OMAP2+: am33xx-hwmod: Fix wrongly terminated am33xx_usbss_mpu_irqs array
sctp: fix Kconfig bug in default cookie hmac selection
EDAC: Cleanup device deregistering path
...
Conflicts:
drivers/media/pci/dm1105/dm1105.c
drivers/media/platform/soc_camera/mx2_camera.c
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Mauro Carvalho Chehab <mchehab@infradead.org>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The above commit were applied only partially; it broke tuner and
demod attach, but the part that added it to ngene_info was missing.
Not sure what happened there, but, without this patch, a regression
would be happening.
Also, gcc complains about a defined but not used symbol.
So, apply manually the missing part.
Cc: Patrice Chotard <patricechotard@free.fr>
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tuner part of Montage rs2000 chip is similar to ts2020 tuner.
Patch to use ts2020 code.
[mchehab@redhat.com: a few CodingStyle fixes]
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Smatch complainst that the call to mantis_evmgr_exit() dereferences "ca"
but then we check it for NULL on the next line. I've moved the NULL
check forward to avoid that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
make the other drivers take use of the separate ts2020 driver
Signed-off-by: Konstantin Dimitrov <kosio.dimitrov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This kind of memcpy() is error-prone. Its replacement with a struct
assignment is prefered because it's type-safe and much easier to read.
Found by coccinelle. Hand patched and reviewed.
Tested by compilation only.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier struct_name;
struct struct_name to;
struct struct_name from;
expression E;
@@
-memcpy(&(to), &(from), E);
+to = from;
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This kind of memcpy() is error-prone. Its replacement with a struct
assignment is prefered because it's type-safe and much easier to read.
Found by coccinelle. Hand patched and reviewed.
Tested by compilation only.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier struct_name;
struct struct_name to;
struct struct_name from;
expression E;
@@
-memcpy(&(to), &(from), E);
+to = from;
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This kind of memcpy() is error-prone. Its replacement with a struct
assignment is prefered because it's type-safe and much easier to read.
Found by coccinelle. Hand patched and reviewed.
Tested by compilation only.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier struct_name;
struct struct_name to;
struct struct_name from;
expression E;
@@
-memcpy(&(to), &(from), E);
+to = from;
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Reviewed-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This kind of memcpy() is error-prone. Its replacement with a struct
assignment is prefered because it's type-safe and much easier to read.
Found by coccinelle. Hand patched and reviewed.
Tested by compilation only.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier struct_name;
struct struct_name to;
struct struct_name from;
expression E;
@@
-memcpy(&(to), &(from), E);
+to = from;
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This kind of memcpy() is error-prone. Its replacement with a struct
assignment is prefered because it's type-safe and much easier to read.
Found by coccinelle. Hand patched and reviewed.
Tested by compilation only.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier struct_name;
struct struct_name to;
struct struct_name from;
expression E;
@@
-memcpy(&(to), &(from), E);
+to = from;
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This kind of memcpy() is error-prone. Its replacement with a struct
assignment is prefered because it's type-safe and much easier to read.
Found by coccinelle. Hand patched and reviewed.
Tested by compilation only.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier struct_name;
struct struct_name to;
struct struct_name from;
expression E;
@@
-memcpy(&(to), &(from), E);
+to = from;
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When the bttv driver is running without i2c_debug being set, the kernel
log is being flooded with the string ">". This string is really a part of
a debug message that is logged using several substrings protected by a
conditional check.
This patch adds the same conditional check to the leaked substring.
Signed-off-by: John Törnblom <john.tornblom@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Previously, demodulator and tuner attach was done in the
demod_attach callback. Migrate the tuner part in the
tuner_attach callback in ngene_info to do thing in right place.
Signed-off-by: Patrice Chotard <patricechotard@free.fr>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The SAA7134 appears to have trouble buffering more than one line of video
when doing DMA. Rather than try to fix the driver to cope (as has been done
by Andy Walls for the cx18 driver), put in a pm_qos_request to limit deep
sleep exit latencies.
The visible effect of not having this is that seemingly random lines are
only partly transferred - if you feed in a static image, you see a portion
of the image "flicker" into place.
[mchehab@redhat.com: Fix ABI breakage due to some renames at pm_qos]
Signed-off-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch provide only analog support.
The device is based on AF9013 demodulator, XC3028 tuner
and CX23885 chipset; subsystem id: 1461:d939
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since most dvb ioctls wrap their real work with dvb_usercopy, the static mutex
used in dvb_usercopy effectively is a global lock for dvb ioctls.
Unfortunately, frontend ioctls can be blocked by the frontend thread for
several seconds; this leads to unacceptable lock contention. Mitigate that by
pushing the mutex from dvb_usercopy down to the individual, device specific
ioctls.
There are 10 such ioctl functions using dvb_usercopy, either calling it
directly, or via the trivial wrapper dvb_generic_ioctl. The following already
employ their own locking and look safe:
• dvb_demux_ioctl (as per dvb_demux_do_ioctl)
• dvb_dvr_ioctl (as per dvb_dvr_do_ioctl)
• dvb_osd_ioctl (as per single non-trivial callee)
• fdtv_ca_ioctl (as per callees)
• dvb_frontend_ioctl
The following functions do not, and are thus changed to use a device specific
mutex:
• dvb_net_ioctl (as per dvb_net_do_ioctl)
• dvb_ca_en50221_io_ioctl (as per dvb_ca_en50221_io_do_ioctl)
• dvb_video_ioctl
• dvb_audio_ioctl
• dvb_ca_ioctl
Signed-off-by: Nikolaus Schulz <schulz@macnetix.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a Kconfig warning that appears with allmodconfig on arm:
warning: (DVB_USB_PCTV452E) selects TTPCI_EEPROM which has unmet direct dependencies (MEDIA_SUPPORT && MEDIA_PCI_SUPPORT && MEDIA_DIGITAL_TV_SUPPORT && I2C)
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This series add remote control support for MyGica X8507.
I test for 2 month under OpenSuse(X64) 11.4 and 12.2 with
kernel 3.4, 3.5, 3.6 also 3.7-rc2 and rc3.
[mchehab@redhat.com: fixed whitespacing - it seems that Alfredo's emailer mangled
it]
Signed-off-by: Alfredo J. Delaiti <alfredodelaiti@netscape.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Based on commit: e66131cee5
Not testing videobuf_dvb_get_frontend output may cause OOPS if it return
NULL. This patch fixes this issue.
The semantic patch that found this issue is(http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i,a,b;
statement S, S2;
@@
i = videobuf_dvb_get_frontend(...);
... when != if (!i) S
* if (i->a.b)
S2
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
display an error message if either tuner_i2c_addr or demod_i2c_addr
are not specified in the tda10071_config structure
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set buffer timestamp flags for videobuf, videobuf2 and drivers that use
neither.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert drivers using wall clock time (CLOCK_REALTIME) to timestamp from the
monotonic timer (CLOCK_MONOTONIC).
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add basic DVB-S2 support for the Hauppauge HVR-4400 PCIe board.
Thanks to Antti Palosaari and Devin Heitmueller for their
suggestions and testing.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace kmemdup for kstrdup and cleanup related code.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The function cx25821_sram_channel_setup_upstream_audio always return zero,
so the return value is not saved any more.
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
While here, replace strlen()+kmemdup() to kstrdup().
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: walter harms <wharms@bfs.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/pci/bt8xx/bttv-driver.c:308:3: warning: initialized field overwritten [-Woverride-init]
drivers/media/pci/bt8xx/bttv-driver.c:308:3: warning: (near initialization for 'bttv_tvnorms[0].cropcap.bounds.height') [-Woverride-init]
drivers/media/pci/bt8xx/bttv-driver.c: In function 'bttv_remove':
drivers/media/pci/bt8xx/bttv-driver.c:4467:29: warning: suggest braces around empty body in an 'if' statement [-Wempty-body]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
get rid of a few warnings about empty body:
drivers/media/pci/ngene/ngene-core.c:756:3: warning: suggest braces around empty body in an 'else' statement [-Wempty-body]
drivers/media/pci/ngene/ngene-cards.c:429:5: warning: suggest braces around empty body in an 'if' statement [-Wempty-body]
Those are due to some commented code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/pci/cx88/cx88-mpeg.c: In function 'cx8802_mpeg_irq':
drivers/media/pci/cx88/cx88-mpeg.c:419:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-mpeg.c: In function 'cx8802_irq':
drivers/media/pci/cx88/cx88-mpeg.c:453:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-alsa.c: In function 'snd_cx88_create':
drivers/media/pci/cx88/cx88-alsa.c:818:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-alsa.c:837:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-alsa.c: In function 'cx88_audio_initdev':
drivers/media/pci/cx88/cx88-alsa.c:912:2: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c: In function 'blackbird_mbox_func':
drivers/media/pci/cx88/cx88-blackbird.c:327:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:333:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:360:4: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c: In function 'blackbird_find_mailbox':
drivers/media/pci/cx88/cx88-blackbird.c:421:2: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c: In function 'blackbird_load_firmware':
drivers/media/pci/cx88/cx88-blackbird.c:444:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:451:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:453:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:459:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:466:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:487:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:492:2: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:503:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c: In function 'blackbird_initialize_codec':
drivers/media/pci/cx88/cx88-blackbird.c:560:4: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:566:4: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:569:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/pci/cx88/cx88.h:97:1: warning: 'inline' is not at beginning of declaration [-Wold-style-declaration]
drivers/media/pci/cx88/cx88.h:103:1: warning: 'inline' is not at beginning of declaration [-Wold-style-declaration]
drivers/media/pci/cx88/cx88-core.c:649:1: warning: 'inline' is not at beginning of declaration [-Wold-style-declaration]
drivers/media/pci/cx88/cx88-core.c:654:1: warning: 'inline' is not at beginning of declaration [-Wold-style-declaration]
drivers/media/pci/cx88/cx88-core.c:659:1: warning: 'inline' is not at beginning of declaration [-Wold-style-declaration]
drivers/media/pci/cx88/cx88-core.c:664:1: warning: 'inline' is not at beginning of declaration [-Wold-style-declaration]
drivers/media/pci/cx88/cx88-core.c:684:1: warning: 'inline' is not at beginning of declaration [-Wold-style-declaration]
drivers/media/pci/cx88/cx88-core.c:695:1: warning: 'inline' is not at beginning of declaration [-Wold-style-declaration]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/pci/saa7164/saa7164-api.c:1489:5: warning: no previous prototype for 'saa7164_api_modify_gpio' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-api.c:168:5: warning: no previous prototype for 'saa7164_api_set_gop_size' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-api.c:622:5: warning: no previous prototype for 'saa7164_api_set_dif' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-api.c:825:5: warning: no previous prototype for 'saa7164_api_configure_port_vbi' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-api.c:861:5: warning: no previous prototype for 'saa7164_api_configure_port_mpeg2ts' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-api.c:895:5: warning: no previous prototype for 'saa7164_api_configure_port_mpeg2ps' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-api.c:928:5: warning: no previous prototype for 'saa7164_api_dump_subdevs' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-bus.c:109:6: warning: no previous prototype for 'saa7164_bus_dumpmsg' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-bus.c:84:6: warning: no previous prototype for 'saa7164_bus_verify' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-cmd.c:135:5: warning: no previous prototype for 'saa7164_cmd_dequeue' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-cmd.c:189:5: warning: no previous prototype for 'saa7164_cmd_set' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-cmd.c:262:5: warning: no previous prototype for 'saa7164_cmd_wait' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-cmd.c:26:5: warning: no previous prototype for 'saa7164_cmd_alloc_seqno' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-cmd.c:45:6: warning: no previous prototype for 'saa7164_cmd_free_seqno' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-cmd.c:57:6: warning: no previous prototype for 'saa7164_cmd_timeout_seqno' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-cmd.c:67:5: warning: no previous prototype for 'saa7164_cmd_timeout_get' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-encoder.c:1104:29: warning: no previous prototype for 'saa7164_enc_next_buf' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-encoder.c:1290:5: warning: no previous prototype for 'saa7164_g_chip_ident' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-encoder.c:1300:5: warning: no previous prototype for 'saa7164_g_register' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-encoder.c:1313:5: warning: no previous prototype for 'saa7164_s_register' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-fw.c:40:5: warning: no previous prototype for 'saa7164_dl_wait_ack' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-fw.c:56:5: warning: no previous prototype for 'saa7164_dl_wait_clr' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-fw.c:74:5: warning: no previous prototype for 'saa7164_downloadimage' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-vbi.c:1050:29: warning: no previous prototype for 'saa7164_vbi_next_buf' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-vbi.c:987:5: warning: no previous prototype for 'saa7164_vbi_fmt' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/pci/mantis/mantis_input.c:107:5: warning: no previous prototype for 'mantis_input_init' [-Wmissing-prototypes]
drivers/media/pci/mantis/mantis_input.c:153:5: warning: no previous prototype for 'mantis_exit' [-Wmissing-prototypes]
drivers/media/pci/mantis/mantis_uart.c:64:5: warning: no previous prototype for 'mantis_uart_read' [-Wmissing-prototypes]
drivers/media/pci/mantis/mantis_vp1033.c:118:5: warning: no previous prototype for 'lgtdqcs001f_set_symbol_rate' [-Wmissing-prototypes]
drivers/media/pci/mantis/mantis_vp1033.c:86:5: warning: no previous prototype for 'lgtdqcs001f_tuner_set' [-Wmissing-prototypes]
Note: there is already a mantis_exit at the mantis driver. So,
this should be renamed to mantis_input_exit.
The mantis_input code is currently unused, as it doesn't implement the RC API
right.
Patches for it are sent for discussions, but were never
accepted. So, while this is not fixed, the entire code inside
mantis_input can simply be commented.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/pci/ivtv/ivtv-ioctl.c: In function 'ivtv_s_input':
drivers/media/pci/ivtv/ivtv-ioctl.c:996:2: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
Cc: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/pci/ivtv/ivtv-alsa-main.c:208:5: warning: no previous prototype for 'ivtv_alsa_load' [-Wmissing-prototypes]
drivers/media/pci/ivtv/ivtv-alsa-pcm.c:325:5: warning: no previous prototype for 'snd_ivtv_pcm_create' [-Wmissing-prototypes]
drivers/media/pci/ivtv/ivtv-alsa-pcm.c:72:6: warning: no previous prototype for 'ivtv_alsa_announce_pcm_data' [-Wmissing-prototypes]
drivers/media/pci/ivtv/ivtv-firmware.c:279:5: warning: no previous prototype for 'ivtv_firmware_restart' [-Wmissing-prototypes]
drivers/media/pci/ivtv/ivtv-ioctl.c:1171:5: warning: no previous prototype for 'ivtv_s_std' [-Wmissing-prototypes]
Cc: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/pci/cx25821/cx25821-audio-upstream.c:136:5: warning: no previous prototype for 'cx25821_risc_buffer_upstream_audio' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-audio-upstream.c:200:6: warning: no previous prototype for 'cx25821_free_memory_audio' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-audio-upstream.c:259:5: warning: no previous prototype for 'cx25821_get_audio_data' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-audio-upstream.c:354:5: warning: no previous prototype for 'cx25821_openfile_audio' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-audio-upstream.c:47:5: warning: no previous prototype for 'cx25821_sram_channel_setup_upstream_audio' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-audio-upstream.c:493:5: warning: no previous prototype for 'cx25821_audio_upstream_irq' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-audio-upstream.c:637:5: warning: no previous prototype for 'cx25821_start_audio_dma_upstream' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-biffuncs.h:28:11: warning: no previous prototype for 'getBit' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-biffuncs.h:33:12: warning: no previous prototype for 'clearBitAtPos' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-biffuncs.h:38:12: warning: no previous prototype for 'setBitAtPos' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-i2c.c:332:6: warning: no previous prototype for 'cx25821_av_clk' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-video.c:294:5: warning: no previous prototype for 'cx25821_restart_video_queue' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-video.c:345:6: warning: no previous prototype for 'cx25821_vid_timeout' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-video-upstream.c:176:5: warning: no previous prototype for 'cx25821_risc_buffer_upstream' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-video-upstream.c:303:5: warning: no previous prototype for 'cx25821_get_frame' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-video-upstream.c:408:5: warning: no previous prototype for 'cx25821_openfile' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-video-upstream.c:489:5: warning: no previous prototype for 'cx25821_upstream_buffer_prepare' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-video-upstream.c:551:5: warning: no previous prototype for 'cx25821_video_upstream_irq' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-video-upstream.c:667:6: warning: no previous prototype for 'cx25821_set_pixelengine' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-video-upstream.c:699:5: warning: no previous prototype for 'cx25821_start_video_dma_upstream' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-video-upstream-ch2.c:126:5: warning: no previous prototype for 'cx25821_risc_buffer_upstream_ch2' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-video-upstream-ch2.c:258:5: warning: no previous prototype for 'cx25821_get_frame_ch2' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-video-upstream-ch2.c:363:5: warning: no previous prototype for 'cx25821_openfile_ch2' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-video-upstream-ch2.c:510:5: warning: no previous prototype for 'cx25821_video_upstream_irq_ch2' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-video-upstream-ch2.c:650:5: warning: no previous prototype for 'cx25821_start_video_dma_upstream_ch2' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change dprintk logic to avoid the following warning:
drivers/media/pci/cx23885/cx23885-alsa.c: In function 'cx23885_audio_register':
drivers/media/pci/cx23885/cx23885-alsa.c:515:2: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/pci/cx23885/altera-ci.c:266:5: warning: no previous prototype for 'altera_ci_op_cam' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:301:5: warning: no previous prototype for 'altera_ci_read_attribute_mem' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:307:5: warning: no previous prototype for 'altera_ci_write_attribute_mem' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:313:5: warning: no previous prototype for 'altera_ci_read_cam_ctl' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:319:5: warning: no previous prototype for 'altera_ci_write_cam_ctl' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:325:5: warning: no previous prototype for 'altera_ci_slot_reset' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:368:5: warning: no previous prototype for 'altera_ci_slot_shutdown' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:374:5: warning: no previous prototype for 'altera_ci_slot_ts_ctl' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:451:5: warning: no previous prototype for 'altera_poll_ci_slot_status' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:462:6: warning: no previous prototype for 'altera_hw_filt_release' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:584:5: warning: no previous prototype for 'altera_pid_feed_control' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:606:5: warning: no previous prototype for 'altera_ci_start_feed' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:613:5: warning: no previous prototype for 'altera_ci_stop_feed' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:620:5: warning: no previous prototype for 'altera_ci_start_feed_1' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:625:5: warning: no previous prototype for 'altera_ci_stop_feed_1' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:630:5: warning: no previous prototype for 'altera_ci_start_feed_2' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:635:5: warning: no previous prototype for 'altera_ci_stop_feed_2' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:640:5: warning: no previous prototype for 'altera_hw_filt_init' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:123:5: warning: no previous prototype for 'netup_write_i2c' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:150:5: warning: no previous prototype for 'netup_ci_get_mem' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:169:5: warning: no previous prototype for 'netup_ci_op_cam' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:239:5: warning: no previous prototype for 'netup_ci_read_attribute_mem' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:245:5: warning: no previous prototype for 'netup_ci_write_attribute_mem' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:251:5: warning: no previous prototype for 'netup_ci_read_cam_ctl' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:257:5: warning: no previous prototype for 'netup_ci_write_cam_ctl' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:263:5: warning: no previous prototype for 'netup_ci_slot_reset' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:292:5: warning: no previous prototype for 'netup_ci_slot_shutdown' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:298:5: warning: no previous prototype for 'netup_ci_set_irq' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:319:5: warning: no previous prototype for 'netup_ci_slot_ts_ctl' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:375:5: warning: no previous prototype for 'netup_ci_slot_status' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:402:5: warning: no previous prototype for 'netup_poll_ci_slot_status' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:415:5: warning: no previous prototype for 'netup_ci_init' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:520:6: warning: no previous prototype for 'netup_ci_exit' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:90:5: warning: no previous prototype for 'netup_read_i2c' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-av.c:26:6: warning: no previous prototype for 'cx23885_av_work_handler' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-cards.c:1430:5: warning: no previous prototype for 'netup_jtag_io' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-core.c:306:6: warning: no previous prototype for 'cx23885_irq_add' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-dvb.c:662:5: warning: no previous prototype for 'netup_altera_fpga_rw' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-f300.c:150:5: warning: no previous prototype for 'f300_set_voltage' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-input.c:249:5: warning: no previous prototype for 'cx23885_input_init' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-input.c:353:6: warning: no previous prototype for 'cx23885_input_fini' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-input.c:76:6: warning: no previous prototype for 'cx23885_input_rx_work_handler' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-ioctl.c:134:5: warning: no previous prototype for 'cx23885_g_register' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-ioctl.c:185:5: warning: no previous prototype for 'cx23885_s_register' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-ioctl.c:27:5: warning: no previous prototype for 'cx23885_g_chip_ident' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-ir.c:101:6: warning: no previous prototype for 'cx23885_ir_tx_v4l2_dev_notify' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-ir.c:37:6: warning: no previous prototype for 'cx23885_ir_rx_work_handler' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-ir.c:60:6: warning: no previous prototype for 'cx23885_ir_tx_work_handler' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-ir.c:76:6: warning: no previous prototype for 'cx23885_ir_rx_v4l2_dev_notify' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23888-ir.c:1203:5: warning: no previous prototype for 'cx23888_ir_probe' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23888-ir.c:1253:5: warning: no previous prototype for 'cx23888_ir_remove' [-Wmissing-prototypes]
drivers/media/pci/cx23885/netup-init.c:109:6: warning: no previous prototype for 'netup_initialize' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/pci/cx18/cx18-alsa-main.c:200:5: warning: no previous prototype for 'cx18_alsa_load' [-Wmissing-prototypes]
drivers/media/pci/cx18/cx18-alsa-pcm.c:325:5: warning: no previous prototype for 'snd_cx18_pcm_create' [-Wmissing-prototypes]
drivers/media/pci/cx18/cx18-alsa-pcm.c:72:6: warning: no previous prototype for 'cx18_alsa_announce_pcm_data' [-Wmissing-prototypes]
drivers/media/pci/cx18/cx18-streams.c💯6: warning: no previous prototype for 'cx18_dma_free' [-Wmissing-prototypes]
Cc: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The RC_TYPE_* defines are currently used both where a single protocol is
expected and where a bitmap of protocols is expected.
Functions like rc_keydown() and functions which add/remove entries to the
keytable want a single protocol. Future userspace APIs would also
benefit from numeric protocols (rather than bitmap ones). Keytables are
smaller if they can use a small(ish) integer rather than a bitmap.
Other functions or struct members (e.g. allowed_protos,
enabled_protocols, etc) accept multiple protocols and need a bitmap.
Using different types reduces the risk of programmer error. Using a
protocol enum whereever possible also makes for a more future-proof
user-space API as we don't need to worry about a sufficient number of
bits being available (e.g. in structs used for ioctl() calls).
The use of both a number and a corresponding bit is dalso one in e.g.
the input subsystem as well (see all the references to set/clear bit when
changing keytables for example).
This patch separate the different usages in preparation for
upcoming patches.
Where a single protocol is expected, enum rc_type is used; where one or more
protocol(s) are expected, something like u64 is used.
The patch has been rewritten so that the format of the sysfs "protocols"
file is no longer altered (at the loss of some detail). The file itself
should probably be deprecated in the future though.
Signed-off-by: David Härdeman <david@hardeman.nu>
Cc: Andy Walls <awalls@md.metrocast.net>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Antti Palosaari <crope@iki.fi>
Cc: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using list_move_tail() instead of list_del() + list_add_tail().
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using list_move_tail() instead of list_del() + list_add_tail().
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The only reason for this header is to make sure that include
linux/time.h were added before uapi/*/dmx.h. Just push down the
time.h header on the few places where this is used, and drop
this new header.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull second set of media updates from Mauro Carvalho Chehab:
"Despite its size, most of the stuff here is trivial. This series
contains:
- s5p-mfc: additions at the driver and at the core to support H.264
hardware codec;
- Some improvements at s5p and davinci embedded drivers;
- Some V4L2 compliance fixes applied on a few drivers;
- Several random trivial patches, including several fixes and a few
new board support additions;
Notes:
1) Some Exynos media patches were dependent on some -arm fixes that
got merged on changeset 782cd9e. That's why this pull request is
based that changeset.
2) As promised, I reviewed the pending VB2 DMABUF series.
While setting a test environment, it was noticed that the upstream
support for Samsung Exynos 4 boards (smdk310 and Origen) are
broken upstream, likely due to regressions: both defconfigs are
wrong and regulator settings for both boards are broken. That,
allied with some bug at the dummy regulator driver, causes OOPSes
during boot time.
Long story short: even fixing the above, the proposed patches
OOPSed when running the DMABUF test. Not sure yet if the OOPSes
are due to some other undetected regressions, or due to some bug
on the patches.
Due to the above, DMABUF patches for vb2 got NACKed for 3.7."
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (109 commits)
[media] m5mols: Add missing #include <linux/sizes.h>
[media] stk1160: Add support for S-Video input
Revert "[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check"
[media] dvb: LNA implementation changes
[media] v4l2-ioctl: fix W=1 warnings
[media] v4l2-ioctl: add blocks check for VIDIOC_SUBDEV_G/S_EDID
[media] omap3isp: Fix compilation error in ispreg.h
[media] rc-msi-digivox-ii: Add full scan keycodes
[media] cx25821: testing the wrong variable
[media] tda18271-common: hold the I2C adapter during write transfers
[media] ds3000: add module parameter to force firmware upload
[media] drivers/media: Remove unnecessary semicolon
[media] winbond: remove space from driver name
[media] iguanair: cannot send data from the stack
[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check
[media] dvb-usb: print small buffers via %*ph
[media] uvc: Add return code check at vb2_queue_init()
[media] em28xx: Replace memcpy with struct assignment
[media] bt8xx: Add video4linux control V4L2_CID_COLOR_KILLER
[media] mem2mem_testdev: Use devm_kzalloc() in probe
...
Conflicts:
arch/arm/mach-davinci/include/mach/da8xx.h
Applied on the top of changeset 782cd9e, as some of those patches
depend on some fixes that went via -arm tree.
* staging/for_v3.7: (109 commits)
[media] m5mols: Add missing #include <linux/sizes.h>
[media] stk1160: Add support for S-Video input
Revert "[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check"
[media] dvb: LNA implementation changes
[media] v4l2-ioctl: fix W=1 warnings
[media] v4l2-ioctl: add blocks check for VIDIOC_SUBDEV_G/S_EDID
[media] omap3isp: Fix compilation error in ispreg.h
[media] rc-msi-digivox-ii: Add full scan keycodes
[media] cx25821: testing the wrong variable
[media] tda18271-common: hold the I2C adapter during write transfers
[media] ds3000: add module parameter to force firmware upload
[media] drivers/media: Remove unnecessary semicolon
[media] winbond: remove space from driver name
[media] iguanair: cannot send data from the stack
[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check
[media] dvb-usb: print small buffers via %*ph
[media] uvc: Add return code check at vb2_queue_init()
[media] em28xx: Replace memcpy with struct assignment
[media] bt8xx: Add video4linux control V4L2_CID_COLOR_KILLER
[media] mem2mem_testdev: Use devm_kzalloc() in probe
...
A long time ago, in v2.4, VM_RESERVED kept swapout process off VMA,
currently it lost original meaning but still has some effects:
| effect | alternative flags
-+------------------------+---------------------------------------------
1| account as reserved_vm | VM_IO
2| skip in core dump | VM_IO, VM_DONTDUMP
3| do not merge or expand | VM_IO, VM_DONTEXPAND, VM_HUGETLB, VM_PFNMAP
4| do not mlock | VM_IO, VM_DONTEXPAND, VM_HUGETLB, VM_PFNMAP
This patch removes reserved_vm counter from mm_struct. Seems like nobody
cares about it, it does not exported into userspace directly, it only
reduces total_vm showed in proc.
Thus VM_RESERVED can be replaced with VM_IO or pair VM_DONTEXPAND | VM_DONTDUMP.
remap_pfn_range() and io_remap_pfn_range() set VM_IO|VM_DONTEXPAND|VM_DONTDUMP.
remap_vmalloc_range() set VM_DONTEXPAND | VM_DONTDUMP.
[akpm@linux-foundation.org: drivers/vfio/pci/vfio_pci.c fixup]
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Eric Paris <eparis@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Kentaro Takeda <takedakn@nttdata.co.jp>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Venkatesh Pallipadi <venki@google.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
->input_filename could be NULL here. The intent was to test
->_filename.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r1@
statement S;
position p,p1;
@@
S@p1;@p
@script:python r2@
p << r1.p;
p1 << r1.p1;
@@
if p[0].line != p1[0].line_end:
cocci.include_match(False)
@@
position r1.p;
@@
-;@p
// </smpl>
[mchehab@redhat.com: some hunks got bitroted; applied only the
ones that succeeds]
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
[crope@iki.fi: For my drivers a8293, af9013, af9015, af9035]
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil
