Commit Graph

9407 Commits

Author SHA1 Message Date
Suzuki Poulose 5b2e478da0 powerpc/44x: Enable CRASH_DUMP for 440x
Now that we have relocatable kernel, supporting CRASH_DUMP only requires
turning the switches on for UP machines.

We don't have kexec support on 47x yet. Enabling SMP support would be done
as part of enabling the PPC_47x support.

Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
2011-12-20 10:22:14 -05:00
Suzuki Poulose 26ecb6c44b powerpc/44x: Enable CONFIG_RELOCATABLE for PPC44x
The following patch adds relocatable kernel support - based on processing
of dynamic relocations - for PPC44x kernel.

We find the runtime address of _stext and relocate ourselves based
on the following calculation.

	virtual_base = ALIGN(KERNELBASE,256M) +
			MODULO(_stext.run,256M)

relocate() is called with the Effective Virtual Base Address (as
shown below)

            | Phys. Addr| Virt. Addr |
Page (256M) |------------------------|
Boundary    |           |            |
            |           |            |
            |           |            |
Kernel Load |___________|_ __ _ _ _ _|<- Effective
Addr(_stext)|           |      ^     |Virt. Base Addr
            |           |      |     |
            |           |      |     |
            |           |reloc_offset|
            |           |      |     |
            |           |      |     |
            |           |______v_____|<-(KERNELBASE)%256M
            |           |            |
            |           |            |
            |           |            |
Page(256M)  |-----------|------------|
Boundary    |           |            |

The virt_phys_offset is updated accordingly, i.e,

	virt_phys_offset = effective. kernel virt base - kernstart_addr

I have tested the patches on 440x platforms only. However this should
work fine for PPC_47x also, as we only depend on the runtime address
and the current TLB XLAT entry for the startup code, which is available
in r25. I don't have access to a 47x board yet. So, it would be great if
somebody could test this on 47x.

Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Tony Breeds <tony@bakeyournoodle.com>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
2011-12-20 10:21:57 -05:00
Suzuki Poulose 368ff8f14d powerpc: Define virtual-physical translations for RELOCATABLE
We find the runtime address of _stext and relocate ourselves based
on the following calculation.

	virtual_base = ALIGN(KERNELBASE,KERNEL_TLB_PIN_SIZE) +
			MODULO(_stext.run,KERNEL_TLB_PIN_SIZE)

relocate() is called with the Effective Virtual Base Address (as
shown below)

            | Phys. Addr| Virt. Addr |
Page        |------------------------|
Boundary    |           |            |
            |           |            |
            |           |            |
Kernel Load |___________|_ __ _ _ _ _|<- Effective
Addr(_stext)|           |      ^     |Virt. Base Addr
            |           |      |     |
            |           |      |     |
            |           |reloc_offset|
            |           |      |     |
            |           |      |     |
            |           |______v_____|<-(KERNELBASE)%TLB_SIZE
            |           |            |
            |           |            |
            |           |            |
Page        |-----------|------------|
Boundary    |           |            |

On BookE, we need __va() & __pa() early in the boot process to access
the device tree.

Currently this has been defined as :

#define __va(x) ((void *)(unsigned long)((phys_addr_t)(x) -
						PHYSICAL_START + KERNELBASE)
where:
 PHYSICAL_START is kernstart_addr - a variable updated at runtime.
 KERNELBASE	is the compile time Virtual base address of kernel.

This won't work for us, as kernstart_addr is dynamic and will yield different
results for __va()/__pa() for same mapping.

e.g.,

Let the kernel be loaded at 64MB and KERNELBASE be 0xc0000000 (same as
PAGE_OFFSET).

In this case, we would be mapping 0 to 0xc0000000, and kernstart_addr = 64M

Now __va(1MB) = (0x100000) - (0x4000000) + 0xc0000000
		= 0xbc100000 , which is wrong.

it should be : 0xc0000000 + 0x100000 = 0xc0100000

On platforms which support AMP, like PPC_47x (based on 44x), the kernel
could be loaded at highmem. Hence we cannot always depend on the compile
time constants for mapping.

Here are the possible solutions:

1) Update kernstart_addr(PHSYICAL_START) to match the Physical address of
compile time KERNELBASE value, instead of the actual Physical_Address(_stext).

The disadvantage is that we may break other users of PHYSICAL_START. They
could be replaced with __pa(_stext).

2) Redefine __va() & __pa() with relocation offset

#ifdef	CONFIG_RELOCATABLE_PPC32
#define __va(x) ((void *)(unsigned long)((phys_addr_t)(x) - PHYSICAL_START + (KERNELBASE + RELOC_OFFSET)))
#define __pa(x) ((unsigned long)(x) + PHYSICAL_START - (KERNELBASE + RELOC_OFFSET))
#endif

where, RELOC_OFFSET could be

  a) A variable, say relocation_offset (like kernstart_addr), updated
     at boot time. This impacts performance, as we have to load an additional
     variable from memory.

		OR

  b) #define RELOC_OFFSET ((PHYSICAL_START & PPC_PIN_SIZE_OFFSET_MASK) - \
                      (KERNELBASE & PPC_PIN_SIZE_OFFSET_MASK))

   This introduces more calculations for doing the translation.

3) Redefine __va() & __pa() with a new variable

i.e,

#define __va(x) ((void *)(unsigned long)((phys_addr_t)(x) + VIRT_PHYS_OFFSET))

where VIRT_PHYS_OFFSET :

#ifdef CONFIG_RELOCATABLE_PPC32
#define VIRT_PHYS_OFFSET virt_phys_offset
#else
#define VIRT_PHYS_OFFSET (KERNELBASE - PHYSICAL_START)
#endif /* CONFIG_RELOCATABLE_PPC32 */

where virt_phy_offset is updated at runtime to :

	Effective KERNELBASE - kernstart_addr.

Taking our example, above:

virt_phys_offset = effective_kernelstart_vaddr - kernstart_addr
		 = 0xc0400000 - 0x400000
		 = 0xc0000000
	and

	__va(0x100000) = 0xc0000000 + 0x100000 = 0xc0100000
	 which is what we want.

I have implemented (3) in the following patch which has same cost of
operation as the existing one.

I have tested the patches on 440x platforms only. However this should
work fine for PPC_47x also, as we only depend on the runtime address
and the current TLB XLAT entry for the startup code, which is available
in r25. I don't have access to a 47x board yet. So, it would be great if
somebody could test this on 47x.

Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
2011-12-20 10:21:34 -05:00
Suzuki Poulose 9c5f7d39a8 powerpc: Process dynamic relocations for kernel
The following patch implements the dynamic relocation processing for
PPC32 kernel. relocate() accepts the target virtual address and relocates
 the kernel image to the same.

Currently the following relocation types are handled :

	R_PPC_RELATIVE
	R_PPC_ADDR16_LO
	R_PPC_ADDR16_HI
	R_PPC_ADDR16_HA

The last 3 relocations in the above list depends on value of Symbol indexed
whose index is encoded in the Relocation entry. Hence we need the Symbol
Table for processing such relocations.

Note: The GNU ld for ppc32 produces buggy relocations for relocation types
that depend on symbols. The value of the symbols with STB_LOCAL scope
should be assumed to be zero. - Alan Modra

Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alan Modra <amodra@au1.ibm.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
2011-12-20 10:21:08 -05:00
Suzuki Poulose 2391324545 powerpc/44x: Enable DYNAMIC_MEMSTART for 440x
DYNAMIC_MEMSTART(old RELOCATABLE) was restricted only to PPC_47x variants
of 44x. This patch enables DYNAMIC_MEMSTART for 440x based chipsets.

Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linux ppc dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
2011-12-20 10:20:38 -05:00
Suzuki Poulose 0f890c8d20 powerpc: Rename mapping based RELOCATABLE to DYNAMIC_MEMSTART for BookE
The current implementation of CONFIG_RELOCATABLE in BookE is based
on mapping the page aligned kernel load address to KERNELBASE. This
approach however is not enough for platforms, where the TLB page size
is large (e.g, 256M on 44x). So we are renaming the RELOCATABLE used
currently in BookE to DYNAMIC_MEMSTART to reflect the actual method.

The CONFIG_RELOCATABLE for PPC32(BookE) based on processing of the
dynamic relocations will be introduced in the later in the patch series.

This change would allow the use of the old method of RELOCATABLE for
platforms which can afford to enforce the page alignment (platforms with
smaller TLB size).

Changes since v3:

* Introduced a new config, NONSTATIC_KERNEL, to denote a kernel which is
  either a RELOCATABLE or DYNAMIC_MEMSTART(Suggested by: Josh Boyer)

Suggested-by: Scott Wood <scottwood@freescale.com>
Tested-by: Scott Wood <scottwood@freescale.com>

Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linux ppc dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
2011-12-20 10:20:19 -05:00
Benjamin Herrenschmidt 3f53638c80 powerpc: Fix old bug in prom_init setting of the color
We have an array of 16 entries and a loop of 32 iterations... oops.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-19 14:41:25 +11:00
Paul Mackerras 64968f60e7 powerpc: Only use initrd_end as the limit for alloc_bottom if it's inside the RMO.
As the kernels and initrd's get bigger boot-loaders and possibly
kexec-tools will need to place the initrd outside the RMO.  When this
happens we end up with no lowmem and the boot doesn't get very far.

Only use initrd_end as the limit for alloc_bottom if it's inside the
RMO.

Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-19 14:41:24 +11:00
Anton Blanchard b206590c04 powerpc: Fix comment explaining our VSID layout
We support 16TB of user address space and half a million contexts
so update the comment to reflect this.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-19 14:41:22 +11:00
Andreas Schwab 9f5072d4f6 powerpc: Fix wrong divisor in usecs_to_cputime
Commit d57af9b (taskstats: use real microsecond granularity for CPU times)
renamed msecs_to_cputime to usecs_to_cputime, but failed to update all
numbers on the way.  This causes nonsensical cpu idle/iowait values to be
displayed in /proc/stat (the only user of usecs_to_cputime so far).

This also renames __cputime_msec_factor to __cputime_usec_factor, adapting
its value and using it directly in cputime_to_usecs instead of doing two
multiplications.

Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Acked-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-19 14:41:20 +11:00
David Rientjes 2011b1d0d3 powerpc/mm: Fix section mismatch for read_n_cells
read_n_cells() cannot be marked as .devinit.text since it is referenced
from two functions that are not in that section: of_get_lmb_size() and
hot_add_drconf_scn_to_nid().

Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-19 14:41:18 +11:00
David Rientjes 28e86bdbc9 powerpc/mm: Fix section mismatch for mark_reserved_regions_for_nid
mark_reserved_regions_for_nid() is only called from do_init_bootmem(),
which is in .init.text, so it must be in the same section to avoid a
section mismatch warning.

Reported-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-19 14:41:16 +11:00
Matt Evans 2c9c6ce019 powerpc: Add __SANE_USERSPACE_TYPES__ to asm/types.h for LL64
PPC64 uses long long for u64 in the kernel, but powerpc's asm/types.h
prevents 64-bit userland from seeing this definition, instead defaulting
to u64 == long in userspace.  Some user programs (e.g. kvmtool) may actually
want LL64, so this patch adds a check for __SANE_USERSPACE_TYPES__ so that,
if defined, int-ll64.h is included instead.

Signed-off-by: Matt Evans <matt@ozlabs.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-19 14:41:14 +11:00
Anton Blanchard a66086b819 powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX
Implement a POWER7 optimised copy_to_user/copy_from_user using VMX.
For large aligned copies this new loop is over 10% faster, and for
large unaligned copies it is over 200% faster.

If we take a fault we fall back to the old version, this keeps
things relatively simple and easy to verify.

On POWER7 unaligned stores rarely slow down - they only flush when
a store crosses a 4KB page boundary. Furthermore this flush is
handled completely in hardware and should be 20-30 cycles.

Unaligned loads on the other hand flush much more often - whenever
crossing a 128 byte cache line, or a 32 byte sector if either sector
is an L1 miss.

Considering this information we really want to get the loads aligned
and not worry about the alignment of the stores. Microbenchmarks
confirm that this approach is much faster than the current unaligned
copy loop that uses shifts and rotates to ensure both loads and
stores are aligned.

We also want to try and do the stores in cacheline aligned, cacheline
sized chunks. If the store queue is unable to merge an entire
cacheline of stores then the L2 cache will have to do a
read/modify/write. Even worse, we will serialise this with the stores
in the next iteration of the copy loop since both iterations hit
the same cacheline.

Based on this, the new loop does the following things:

1 - 127 bytes
Get the source 8 byte aligned and use 8 byte loads and stores. Pretty
boring and similar to how the current loop works.

128 - 4095 bytes
Get the source 8 byte aligned and use 8 byte loads and stores,
1 cacheline at a time. We aren't doing the stores in cacheline
aligned chunks so we will potentially serialise once per cacheline.
Even so it is much better than the loop we have today.

4096 - bytes
If both source and destination have the same alignment get them both
16 byte aligned, then get the destination cacheline aligned. Do
cacheline sized loads and stores using VMX.

If source and destination do not have the same alignment, we get the
destination cacheline aligned, and use permute to do aligned loads.

In both cases the VMX loop should be optimal - we always do aligned
loads and stores and are always doing stores in cacheline aligned,
cacheline sized chunks.

To be able to use VMX we must be careful about interrupts and
sleeping. We don't use the VMX loop when in an interrupt (which should
be rare anyway) and we wrap the VMX loop in disable/enable_pagefault
and fall back to the existing copy_tofrom_user loop if we do need to
sleep.

The VMX breakpoint of 4096 bytes was chosen using this microbenchmark:

http://ozlabs.org/~anton/junkcode/copy_to_user.c

Since we are using VMX and there is a cost to saving and restoring
the user VMX state there are two broad cases we need to benchmark:

- Best case - userspace never uses VMX

- Worst case - userspace always uses VMX

In reality a userspace process will sit somewhere between these two
extremes. Since we need to test both aligned and unaligned copies we
end up with 4 combinations. The point at which the VMX loop begins to
win is:

0% VMX
aligned		2048 bytes
unaligned	2048 bytes

100% VMX
aligned		16384 bytes
unaligned	8192 bytes

Considering this is a microbenchmark, the data is hot in cache and
the VMX loop has better store queue merging properties we set the
breakpoint to 4096 bytes, a little below the unaligned breakpoints.

Some future optimisations we can look at:

- Looking at the perf data, a significant part of the cost when a
  task is always using VMX is the extra exception we take to restore
  the VMX state. As such we should do something similar to the x86
  optimisation that restores FPU state for heavy users. ie:

        /*
         * If the task has used fpu the last 5 timeslices, just do a full
         * restore of the math state immediately to avoid the trap; the
         * chances of needing FPU soon are obviously high now
         */
        preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5;

  and

        /*
         * fpu_counter contains the number of consecutive context switches
         * that the FPU is used. If this is over a threshold, the lazy fpu
         * saving becomes unlazy to save the trap. This is an unsigned char
         * so that after 256 times the counter wraps and the behavior turns
         * lazy again; this to deal with bursty apps that only use FPU for
         * a short time
         */

- We could create a paca bit to mirror the VMX enabled MSR bit and check
  that first, avoiding multiple calls to calling enable_kernel_altivec.
  That should help with iovec based system calls like readv.

- We could have two VMX breakpoints, one for when we know the user VMX
  state is loaded into the registers and one when it isn't. This could
  be a second bit in the paca so we can calculate the break points quickly.

- One suggestion from Ben was to save and restore the VSX registers
  we use inline instead of using enable_kernel_altivec.

[BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC]

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-19 14:40:40 +11:00
Richard Kuo 0766387bcf powerpc: Use rwsem.h from generic location
As of commit dd472da38, rwsem.h was moved into asm-generic.
This patch removes the arch file and points the build at
its new location.

Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-16 14:39:48 +11:00
Benjamin Herrenschmidt 1e7342e778 Merge remote-tracking branch 'jwb/next' into next
Conflicts:
	arch/powerpc/platforms/40x/ppc40x_simple.c
2011-12-16 11:24:25 +11:00
Benjamin Herrenschmidt 78c5c68a4c powerpc/pmac: Fix SMP kernels on pre-core99 UP machines
The code for "powersurge" SMP would kick in and cause a crash
at boot due to the lack of a NULL test.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-16 11:10:25 +11:00
Benjamin Herrenschmidt 8e609d5e7b powerpc/pmac: Simplify old pmac PIC interrupt handling
In the old days, we treated all interrupts from the legacy Apple home made
interrupt controllers as level, with a trick reading the "level" register
along with the "event" register to work arounds bugs where it would
occasionally fail to latch some events.

Doing so appeared to work fine for both level and edge interrupts.

Later on, we discovered in Darwin source the magic masks that define which
interrupts are actually level and which are edge, and implemented a
different algorithm, more similar to what Apple does, that treats those
differently.

I recently discovered however that this caused problems (including loss
of interrupts) with an old Wallstreet PowerBook when trying to use the
internal modem (connected to a cascaded controller).

It looks like some interrupts are treated as edge while they are really
level and I'm starting to seriously doubt the correctness of the Darwin
code (which has other obvious bugs when you read it, so ...)

This patch reverts to our original behaviour of treating everything as
a level interrupt. It appears to solve the problems with the modem on
the Wallstreet and everything else seems to be working properly as well.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-16 11:10:11 +11:00
Benjamin Herrenschmidt 43ca5d347a Merge branch 'kexec' into next 2011-12-16 11:09:21 +11:00
Benjamin Herrenschmidt efdad722ef Merge branch 'ps3' into next 2011-12-16 11:09:15 +11:00
Benjamin Herrenschmidt e6f08d37e6 Merge branch 'cpuidle' into next 2011-12-16 11:09:11 +11:00
Martin Schwidefsky 648616343c [S390] cputime: add sparse checking and cleanup
Make cputime_t and cputime64_t nocast to enable sparse checking to
detect incorrect use of cputime. Drop the cputime macros for simple
scalar operations. The conversion macros are still needed.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2011-12-15 14:56:19 +01:00
Grant Likely 1a2d397a6e gpio/powerpc: Eliminate duplication of of_get_named_gpio_flags()
A large chunk of qe_pin_request() is unnecessarily cut-and-paste
directly from of_get_named_gpio_flags().  This patch cuts out the
duplicate code and replaces it with a call to of_get_gpio().

v2: fixed compile error due to missing gpio_to_chip()

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
2011-12-12 13:40:16 -07:00
Frederic Weisbecker 1268fbc746 nohz: Remove tick_nohz_idle_enter_norcu() / tick_nohz_idle_exit_norcu()
Those two APIs were provided to optimize the calls of
tick_nohz_idle_enter() and rcu_idle_enter() into a single
irq disabled section. This way no interrupt happening in-between would
needlessly process any RCU job.

Now we are talking about an optimization for which benefits
have yet to be measured. Let's start simple and completely decouple
idle rcu and dyntick idle logics to simplify.

Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
2011-12-11 10:31:57 -08:00
Paul E. McKenney a7b152d534 powerpc: Tell RCU about idle after hcall tracing
The PowerPC pSeries platform (CONFIG_PPC_PSERIES=y) enables
hypervisor-call tracing for CONFIG_TRACEPOINTS=y kernels.  One of the
hypervisor calls that is traced is the H_CEDE call in the idle loop
that tells the hypervisor that this OS instance no longer needs the
current CPU.  However, tracing uses RCU, so this combination of kernel
configuration variables needs to avoid telling RCU about the current CPU's
idleness until after the H_CEDE-entry tracing completes on the one hand,
and must tell RCU that the the current CPU is no longer idle before the
H_CEDE-exit tracing starts.

In all other cases, it suffices to inform RCU of CPU idleness upon
idle-loop entry and exit.

This commit makes the required adjustments.

Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
2011-12-11 10:31:39 -08:00
Frederic Weisbecker 2bbb6817c0 nohz: Allow rcu extended quiescent state handling seperately from tick stop
It is assumed that rcu won't be used once we switch to tickless
mode and until we restart the tick. However this is not always
true, as in x86-64 where we dereference the idle notifiers after
the tick is stopped.

To prepare for fixing this, add two new APIs:
tick_nohz_idle_enter_norcu() and tick_nohz_idle_exit_norcu().

If no use of RCU is made in the idle loop between
tick_nohz_enter_idle() and tick_nohz_exit_idle() calls, the arch
must instead call the new *_norcu() version such that the arch doesn't
need to call rcu_idle_enter() and rcu_idle_exit().

Otherwise the arch must call tick_nohz_enter_idle() and
tick_nohz_exit_idle() and also call explicitly:

- rcu_idle_enter() after its last use of RCU before the CPU is put
to sleep.
- rcu_idle_exit() before the first use of RCU after the CPU is woken
up.

Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: David Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
2011-12-11 10:31:36 -08:00
Frederic Weisbecker 280f06774a nohz: Separate out irq exit and idle loop dyntick logic
The tick_nohz_stop_sched_tick() function, which tries to delay
the next timer tick as long as possible, can be called from two
places:

- From the idle loop to start the dytick idle mode
- From interrupt exit if we have interrupted the dyntick
idle mode, so that we reprogram the next tick event in
case the irq changed some internal state that requires this
action.

There are only few minor differences between both that
are handled by that function, driven by the ts->inidle
cpu variable and the inidle parameter. The whole guarantees
that we only update the dyntick mode on irq exit if we actually
interrupted the dyntick idle mode, and that we enter in RCU extended
quiescent state from idle loop entry only.

Split this function into:

- tick_nohz_idle_enter(), which sets ts->inidle to 1, enters
dynticks idle mode unconditionally if it can, and enters into RCU
extended quiescent state.

- tick_nohz_irq_exit() which only updates the dynticks idle mode
when ts->inidle is set (ie: if tick_nohz_idle_enter() has been called).

To maintain symmetry, tick_nohz_restart_sched_tick() has been renamed
into tick_nohz_idle_exit().

This simplifies the code and micro-optimize the irq exit path (no need
for local_irq_save there). This also prepares for the split between
dynticks and rcu extended quiescent state logics. We'll need this split to
further fix illegal uses of RCU in extended quiescent states in the idle
loop.

Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: David Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
2011-12-11 10:31:35 -08:00
Paul Gortmaker 9deaa53ac7 serial: add irq handler for Freescale 16550 errata.
Sending a break on the SOC UARTs found in some MPC83xx/85xx/86xx
chips seems to cause a short lived IRQ storm (/proc/interrupts
typically shows somewhere between 300 and 1500 events).  Unfortunately
this renders SysRQ over the serial console completely inoperable.

The suggested workaround in the errata is to read the Rx register,
wait one character period, and then read the Rx register again.
We achieve this by tracking the old LSR value, and on the subsequent
interrupt event after a break, we don't read LSR, instead we just
read the RBR again and return immediately.

The "fsl,ns16550" is used in the compatible field of the serial
device to mark UARTs known to have this issue.

Thanks to Scott Wood for providing the errata data which led to
a much cleaner fix.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-12-09 19:14:13 -08:00
Tony Breeds 228d550533 powerpc/47x: Add support for the new IBM currituck platform
Based on original work by David 'Shaggy' Kleikamp.

Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
2011-12-09 07:51:40 -05:00
Tony Breeds df777bd39a powerpc/476fpe: Add 476fpe SoC code
Based on original work by David 'Shaggy' Kleikamp.

Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
2011-12-09 07:51:02 -05:00
Tony Breeds 075bcf5879 powerpc/boot: Add mfdcrx
Needed for currituck support.

Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
2011-12-09 07:49:50 -05:00
Tony Breeds e32a03290c powerpc/boot: Add extended precision shifts to the boot wrapper.
The upcomming currituck patches will need to do 64-bit shifts which will
fail with undefined symbol without this patch.

I looked at linking against libgcc but we can't guarantee that libgcc
was compiled with soft-float.  Also Using ../lib/div64.S or
../kernel/misc_32.S, this will break the build as the .o's need to be
built with different flags for the bootwrapper vs the kernel.  So for
now the easyest option is to just copy code from
arch/powerpc/kernel/misc_32.S  I don't think this code changes too often ;P

Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
2011-12-09 07:49:27 -05:00
Christoph Egger ca899859f1 powerpc/44x: Removing dead CONFIG_PPC47x
CONFIG_PPC47x doesn't exist in Kconfig and no 476 processor calls this
function ppc44x_pin_tlb() as it has it's own ppc47x_pin_tlb().

This code is probably an artifact of the original 476 code that
shouldn't have made it upstream.

Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
2011-12-09 07:48:56 -05:00
Tony Breeds 466c2bc762 powerpc/44x: pci: Setup the dma_window properties for each pci_controller
Needed if you want to use swiotlb, harmless otherwise.

Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
2011-12-09 07:48:36 -05:00
Tony Breeds 8115846e1a powerpc/44x: pci: Add a want_sdr flag into ppc4xx_pciex_hwops
Currituck doesn't need nor use SDR so aborting the pci setup if there is
no sdr-base would be bad.

Add a flag to ppc4xx_pciex_hwops for the backends to state if they need
SDR and then only complain and abort if they do and it's not found in
the device tree.

Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
2011-12-09 07:47:48 -05:00
Tony Breeds 9fb5529679 powerpc/44x: pci: Use PCI_BASE_ADDRESS_MEM_PREFETCH rather than magic value.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
2011-12-09 07:45:00 -05:00
Tejun Heo 0ee332c145 memblock: Kill early_node_map[]
Now all ARCH_POPULATES_NODE_MAP archs select HAVE_MEBLOCK_NODE_MAP -
there's no user of early_node_map[] left.  Kill early_node_map[] and
replace ARCH_POPULATES_NODE_MAP with HAVE_MEMBLOCK_NODE_MAP.  Also,
relocate for_each_mem_pfn_range() and helper from mm.h to memblock.h
as page_alloc.c would no longer host an alternative implementation.

This change is ultimately one to one mapping and shouldn't cause any
observable difference; however, after the recent changes, there are
some functions which now would fit memblock.c better than page_alloc.c
and dependency on HAVE_MEMBLOCK_NODE_MAP instead of HAVE_MEMBLOCK
doesn't make much sense on some of them.  Further cleanups for
functions inside HAVE_MEMBLOCK_NODE_MAP in mm.h would be nice.

-v2: Fix compile bug introduced by mis-spelling
 CONFIG_HAVE_MEMBLOCK_NODE_MAP to CONFIG_MEMBLOCK_HAVE_NODE_MAP in
 mmzone.h.  Reported by Stephen Rothwell.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
2011-12-08 10:22:09 -08:00
Tejun Heo 1d7cfe18ec powerpc: Use HAVE_MEMBLOCK_NODE_MAP
powerpc doesn't access early_node_map[] directly and enabling
HAVE_MEMBLOCK_NODE_MAP is trivial - replacing add_active_range() calls
with memblock_set_node() and selecting HAVE_MEMBLOCK_NODE_MAP is
enough.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
2011-12-08 10:22:08 -08:00
Tejun Heo 1aadc0560f memblock: s/memblock_analyze()/memblock_allow_resize()/ and update users
The only function of memblock_analyze() is now allowing resize of
memblock region arrays.  Rename it to memblock_allow_resize() and
update its users.

* The following users remain the same other than renaming.

  arm/mm/init.c::arm_memblock_init()
  microblaze/kernel/prom.c::early_init_devtree()
  powerpc/kernel/prom.c::early_init_devtree()
  openrisc/kernel/prom.c::early_init_devtree()
  sh/mm/init.c::paging_init()
  sparc/mm/init_64.c::paging_init()
  unicore32/mm/init.c::uc32_memblock_init()

* In the following users, analyze was used to update total size which
  is no longer necessary.

  powerpc/kernel/machine_kexec.c::reserve_crashkernel()
  powerpc/kernel/prom.c::early_init_devtree()
  powerpc/mm/init_32.c::MMU_init()
  powerpc/mm/tlb_nohash.c::__early_init_mmu()  
  powerpc/platforms/ps3/mm.c::ps3_mm_add_memory()
  powerpc/platforms/embedded6xx/wii.c::wii_memory_fixups()
  sh/kernel/machine_kexec.c::reserve_crashkernel()

* x86/kernel/e820.c::memblock_x86_fill() was directly setting
  memblock_can_resize before populating memblock and calling analyze
  afterwards.  Call memblock_allow_resize() before start populating.

memblock_can_resize is now static inside memblock.c.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: "H. Peter Anvin" <hpa@zytor.com>
2011-12-08 10:22:08 -08:00
Tejun Heo 6fbef13c4f powerpc: Cleanup memblock usage
* early_init_devtree(): Total memory size is aligned to PAGE_SIZE;
  however, alignment isn't enforced if memory_limit is explicitly
  specified.  Simplify the logic and always apply PAGE_SIZE alignment.

* MMU_init(): memblock regions is truncated by directly modifying
  memblock.memory.cnt.  This is incomplete (reserved array is not
  truncated) and unnecessarily low level hindering further memblock
  improvments.  Use memblock_enforce_memory_limit() instead.

* wii_memory_fixups(): Unnecessarily low level direct manipulation of
  memblock regions.  The same result can be achieved using properly
  abstracted operations.  Reimplement using memblock API.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
2011-12-08 10:22:07 -08:00
Tejun Heo fe091c208a memblock: Kill memblock_init()
memblock_init() initializes arrays for regions and memblock itself;
however, all these can be done with struct initializers and
memblock_init() can be removed.  This patch kills memblock_init() and
initializes memblock with struct initializer.

The only difference is that the first dummy entries don't have .nid
set to MAX_NUMNODES initially.  This doesn't cause any behavior
difference.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: "H. Peter Anvin" <hpa@zytor.com>
2011-12-08 10:22:07 -08:00
Tejun Heo 1c16d242aa memblock: Fix include breakages caused by 24aa07882b
24aa07882b (memblock, x86: Replace memblock_x86_reserve/free_range()
with generic ones) removed arch/x86/include/asm/memblock.h and dropped
its inclusion from include/linux/memblock.h which breaks other
architectures which depended on the generic memblock.h pulling in the
arch specific one.

However, the proper fix isn't adding back the asm inclusion.  memblock
doesn't have any arch dependent part and doesn't need arch specific
header file and asm/memblock.h files are either practically empty or
contain mostly unrelated arch specific stuff.

* In microblaze, sh, powerpc, sparc and openrisc, asm/memblock.h is
  either empty or just contains unused MEMBLOCK_DBG() macro.  Remove
  them.

* In arm and unicore32, asm/memblock.h contains arch specific stuff.
  Include it directly from its users.  It might be a good idea to
  rename the header file to avoid confusion.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: "H. Peter Anvin" <hpa@zytor.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
2011-12-08 10:22:06 -08:00
Anton Blanchard 7c637b04fb powerpc: Enable squashfs as a module
Most distros use it so we may as well enable it and get regular compile
testing.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 14:22:54 +11:00
Anton Blanchard 120a52c388 powerpc/nvram: Add spinlock to oops_to_nvram to prevent oops in compression code.
When issuing a system reset we almost always oops in the oops_to_nvram
code because multiple CPUs are using the deflate work area. Add a
spinlock to protect it.

To play it safe I'm using trylock to avoid locking up if the NVRAM
code oopses. This means we might miss multiple CPUs oopsing at exactly
the same time but I think it's best to play it safe for now. Once we
are happy with the reliability we can change it to a full spinlock.

Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Jim Keniston <jkenisto@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 14:22:54 +11:00
Paul Mackerras 2fde6d20bb powerpc: Provide a way for KVM to indicate that NV GPR values are lost
This fixes a problem where a CPU thread coming out of nap mode can
think it has valid values in the nonvolatile GPRs (r14 - r31) as saved
away in power7_idle, but in fact the values have been trashed because
the thread was used for KVM in the mean time.  The result is that the
thread crashes because code that called power7_idle (e.g.,
pnv_smp_cpu_kill_self()) goes to use values in registers that have
been trashed.

The bit field in SRR1 that tells whether state was lost only reflects
the most recent nap, which may not have been the nap instruction in
power7_idle.  So we need an extra PACA field to indicate that state
has been lost even if SRR1 indicates that the most recent nap didn't
lose state.  We clear this field when saving the state in power7_idle,
we set it to a non-zero value when we use the thread for KVM, and we
test it in power7_wakeup_noloss.

Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 14:22:53 +11:00
Paul Mackerras cba313da5c powerpc/powernv: Fix problems in onlining CPUs
At present, on the powernv platform, if you off-line a CPU that was
online, and then try to on-line it again, the kernel generates a
warning message "OPAL Error -1 starting CPU n".  Furthermore, if the
CPU is a secondary thread that was used by KVM while it was off-line,
the CPU fails to come online.

The first problem is fixed by only calling OPAL to start the CPU the
first time it is on-lined, as indicated by the cpu_start field of its
PACA being zero.  The second problem is fixed by restoring the
cpu_start field to 1 instead of 0 when using the CPU within KVM.

Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 14:22:53 +11:00
Anton Blanchard 3339264042 powerpc/pseries: Increase minimum RMO size from 64MB to 256MB
The minimum RMO size field in ibm,client-architecture is currently
ignored, but a future firmware version will rectify that. Since we
always get at least 128MB of RMO right now, asking for 64MB is
likely to result in boot failures.

We should bump it to at least 128MB, but considering all the boot
issues we have on 128MB RMO boxes and all new machines have virtual
RMO, we may as well set our minimum to 256MB.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 14:22:53 +11:00
sukadev@linux.vnet.ibm.com 8a3e3d31d1 powerpc: Punch a hole in /dev/mem for librtas
With CONFIG_STRICT_DEVMEM=y, user space cannot read any part of /dev/mem.
Since this breaks librtas, punch a hole in /dev/mem to allow access to the
rmo_buffer that librtas needs.

Anton Blanchard reported the problem and helped with the fix.

A quick test for this patch:

       # cat /proc/rtas/rmo_buffer
       000000000f190000 10000

       # python -c "print 0x000000000f190000 / 0x10000"
       3865

       # dd if=/dev/mem of=/tmp/foo count=1 bs=64k skip=3865
       1+0 records in
       1+0 records out
       65536 bytes (66 kB) copied, 0.000205235 s, 319 MB/s

       # dd if=/dev/mem of=/tmp/foo
       dd: reading `/dev/mem': Operation not permitted
       0+0 records in
       0+0 records out
       0 bytes (0 B) copied, 0.00022519 s, 0.0 kB/s

Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 14:22:52 +11:00
Benjamin Herrenschmidt 11eab297f5 powerpc: Add support for OpenBlockS 600
So I've had one of these for a while and it looks like the vendor never
bothered submitting the support upstream.

This adds it using ppc40x_simple and provides a device-tree.

There are some changes to the boot wrapper because the way u-boot works
on this thing, it seems to expect a multipart image with the kernel,
initrd and dtb in it.

The USB support is missing as it needs the yet unmerged driver for
the DWC OTG part and the GPIOs may need further definition in the dts.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 14:22:52 +11:00
Geoff Levand 987706acf8 powerpc/ps3: Update ps3_defconfig
Refresh ps3_defconfig to latest kernel sources and
change the options:

  CONFIG_PPP=m to CONFIG_PPP=n.
  CONFIG_NAMESPACES=y to CONFIG_NAMESPACES=n
  CONFIG_NUMA=y to CONFIG_NUMA=n

Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 14:05:56 +11:00
Geoff Levand b9ec60dc35 powerpc/ps3: Add __init to ps3_smp_probe
Add an __init annotation to the ps3_smp_probe() routine.
Fixes build warnings like these when
CONFIG_DEBUG_SECTION_MISMATCH=y:

 WARNING: Section mismatch in reference from the function .ps3_smp_probe()

Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 14:05:55 +11:00
Geoff Levand 4bf94ae39c powerpc/ps3: Fix PS3 repository build warnings
Fix some PS3 repository.c build warnings when DEBUG is
defined. Also change most pr_debug calls to pr_devel calls.

Fixes warnings like these:

  format '%lx' expects type 'long unsigned int', but argument 7 has type 'u64'

Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 14:05:55 +11:00
Geoff Levand 7f8cd35230 powerpc/ps3: Fix hcall lv1_read_repository_node
The lv1 hcall #91 should be named lv1_read_repository_node, and
not lv1_get_repository_node_value.  Adjust the lv1 hcall table
and all calls.

Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 14:05:55 +11:00
Geoff Levand 816cb49a4b powerpc/ps3: Fix hcall lv1_get_version_info
The lv1_get_version_info hcall takes 2, not 1 output
arguments.  Adjust the lv1 hcall table and all calls.

Usage:

  int lv1_get_version_info(u64 *version_number, u64 *vendor_id)

Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 14:05:54 +11:00
Geoff Levand b5ecc5595e powerpc/ps3: Fix hcall lv1_get_virtual_address_space_id_of_ppe
The lv1_get_virtual_address_space_id_of_ppe hcall takes 0, not 1 input
arguments.  Adjust the lv1 hcall table and all calls.

Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 14:05:54 +11:00
Geoff Levand 7652918cf9 powerpc/ps3: Fix hcall lv1_net_stop_rx_dma
The lv1_net_stop_tx_dma and net_stop_rx_dma hcalls take 2, not 3 input
arguments.  Adjust the lv1 hcall table and all calls.

Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 14:05:54 +11:00
Geoff Levand 32b9074bf8 powerpc/ps3: Interrupt code cleanup
General code cleanup for PS3 interrupt.c:

 o Fill out comments for structure members.
 o Move variables ipi_debug_brk_mask and lock from struct ps3_bmp to
   struct ps3_private.
 o Fix pr_debug build errors when DEBUG is defined.
 o Convert bit operation to set_bit().
 o Convert DBG macro from pr_debug to pr_devel
 o Add new macro FAIL to replace pr_debug calls

Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 14:05:54 +11:00
Anton Blanchard 2440c01e10 powerpc/kdump: Only save CPU state first time through the secondary CPU capture code
We might enter the secondary CPU capture code twice, eg if we have to
unstick some CPUs with a system reset. In this case we don't want to
overwrite the state on CPUs that had made it into the capture code OK,
so use the cpus_state_saved cpumask for that and make it local to
crash_ipi_callback.

For controlling progress now use atomic_t cpus_in_crash to count how
many CPUs have made it into the kdump code, and time_to_dump to tell
everyone it's time to dump.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 14:02:24 +11:00
Anton Blanchard 549e88a134 powerpc/kdump: Delay before sending IPI on a system reset
If we enter the kdump code via system reset, wait a bit before
sending the IPI to capture all secondary CPUs. Without it we race
with the hypervisor that is issuing the system reset to each CPU.
If the IPI gets there first the system reset oops output then shows
the register state of the IPI handler which is not what we want.

I took the opportunity to add defines for all the various delays
we have. There's no need for cpu_relax when we are doing an mdelay,
so remove them too.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 14:02:24 +11:00
Anton Blanchard 90e8f57cf8 powerpc/xics: Reset the CPPR if H_EOI fails
I have an intermittent kdump fail where the hypervisor fails an H_EOI.
As a result our CPPR is never reset to 0xff and we no longer accept
interrupts.

This patch calls icp_hv_set_cppr to reset the CPPR if H_EOI fails,
fixing the kdump fail.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 14:02:23 +11:00
Anton Blanchard a934904d8a powerpc: Reduce pseries panic timeout from 180s to 10s
We've had a 180 second panic timeout on ppc64 for as long as I
can remember. This patch reduces it to 10 seconds on pseries for a few
reasons:

- Almost all pseries machines have a hypervisor console so panic
  output will be available in a scrollback buffer.

- The 180 seconds impacts our availability, users (other than
  kernel hackers) just want the box to come back around so it
  can continue its work.

- I spend a lot of my life staring at the 180 second panic timeout.
  Many pseries machines take minutes to power cycle, so it's quicker
  to sit through the 180 seconds than it is to power cycle.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 14:02:23 +11:00
Anton Blanchard 760ca4dc90 powerpc: Rework die()
Our die() code was based off a very old x86 version. Update it to
mirror the current x86 code.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 14:02:23 +11:00
Anton Blanchard 8c27474a25 powerpc: Cleanup crash/kexec code
Remove some unnecessary defines and fix some spelling mistakes.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 14:02:23 +11:00
Anton Blanchard 07fe0c6132 powerpc/kdump: Use setjmp/longjmp to handle kdump and system reset recursion
We can handle recursion caused by system reset by reusing the crash
shutdown fault handler.

Since we don't have an OS triggerable NMI, if all CPUs don't make it
into kdump then we tell the user to issue a system reset. However if
we have a panic timeout set we cannot wait forever and must continue
the kdump.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 14:02:22 +11:00
Anton Blanchard 9b00ac0697 powerpc: Remove broken and complicated kdump system reset code
We have a lot of complicated logic that handles possible recursion between
kdump and a system reset exception. We can solve this in a much simpler
way using the same setjmp/longjmp tricks xmon does.

As a first step, this patch removes the old system reset code.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 14:02:22 +11:00
Anton Blanchard 58154c8ce7 powerpc: Give us time to get all oopses out before panicking
I've been seeing truncated output when people send system reset info
to me. We should see a backtrace for every CPU, but the panic() code
takes the box down before they all make it out to the console. The
panic code runs unlocked so we also see corrupted console output.

If we are going to panic, then delay 1 second before calling into the
panic code. Move oops_exit inside the die lock and put a newline
between oopses for clarity.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 14:02:22 +11:00
Deepthi Dharwar e8bb3e00cf powerpc/cpuidle: Handle power_save=off
This patch makes pseries_idle_driver not to be registered when
power_save=off kernel boot option is specified. The
cpuidle_disable variable used here is similar to
its usage on x86. If cpuidle_disable is set then
sysfs entries for cpuidle framework are not created
and the required drivers are not loaded.

Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Trinabh Gupta <g.trinabh@gmail.com>
Signed-off-by: Arun R Bharadwaj <arun.r.bharadwaj@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 13:57:34 +11:00
Deepthi Dharwar e179816ce6 powerpc/cpuidle: Enable cpuidle and directly call cpuidle_idle_call() for pSeries
This patch enables cpuidle for pSeries and pSeries_idle is
directly called from the idle loop. As a result of pSeries_idle, cpuidle
driver registered with cpuidle subsystem comes into action. On
failure of loading of the driver or cpuidle framework default idle
is executed as part of the function. This patch
also removes the routines pseries_shared_idle_sleep and
pseries_dedicated_idle_sleep as they are now implemented as part of
pseries_idle cpuidle driver.

Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Trinabh Gupta <g.trinabh@gmail.com>
Signed-off-by: Arun R Bharadwaj <arun.r.bharadwaj@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 13:57:20 +11:00
Deepthi Dharwar 707827f338 powerpc/cpuidle: cpuidle driver for pSeries
This patch implements a back-end cpuidle driver for pSeries
based on pseries_dedicated_idle_loop and pseries_shared_idle_loop
routines.  The driver is built only if CONFIG_CPU_IDLE is set. This
cpuidle driver uses global registration of idle states and
not per-cpu.

Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Trinabh Gupta <g.trinabh@gmail.com>
Signed-off-by: Arun R Bharadwaj <arun.r.bharadwaj@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 13:56:31 +11:00
Deepthi Dharwar 771dae8189 powerpc/cpuidle: Add cpu_idle_wait() to allow switching of idle routines
This patch provides cpu_idle_wait() routine for the powerpc
platform which is required by the cpuidle subsystem. This
routine is required to change the idle handler on SMP systems.
The equivalent routine for x86 is in arch/x86/kernel/process.c
but the powerpc implementation is different.

cpuidle_disable variable is to enable/disable cpuidle
framework if power_save option is set during the boot
time.

Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Trinabh Gupta <g.trinabh@gmail.com>
Signed-off-by: Arun R Bharadwaj <arun.r.bharadwaj@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 13:54:58 +11:00
Benjamin Herrenschmidt faa8bf8878 Merge branch 'booke-hugetlb' into next 2011-12-08 13:20:34 +11:00
Benjamin Herrenschmidt 48b1bf86c3 Merge branch 'mpic' into next 2011-12-07 18:22:47 +11:00
Benjamin Herrenschmidt 4666ca2aa3 powerpc/pci: Make pci_read_irq_line() static
It's only used inside the same file where it's defined. There's
also no point exporting it anymore.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-07 18:04:58 +11:00
Benjamin Herrenschmidt 40dfef66a9 powerpc/powernv: Workaround OFW issues in prom_init.c
Open Firmware on OPAL machines seems to have issues if we close
stdin and/or we try to print things after calling "quiesce" so
we avoid doing both.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-07 18:04:53 +11:00
Benjamin Herrenschmidt cee72d5bb4 powerpc/powernv: Display diag data on p7ioc EEH errors
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-07 18:04:02 +11:00
Benjamin Herrenschmidt f11fe5524a powerpc/powernv: Update OPAL interfaces
This adds some more interfaces for OPAL v2

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-07 18:02:02 +11:00
Becky Bruce 1f6820b4c1 powerpc: Define/use HUGETLB_NEED_PRELOAD insead of complicated #if
Define HUGETLB_NEED_PRELOAD in mmu-book3e.h for CONFIG_PPC64 instead
of having a much more complicated #if block.  This is easier to read
and maintain.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-07 16:26:24 +11:00
Becky Bruce d93e4d7d72 powerpc/book3e: Change hugetlb preload to take vma argument
This avoids an extra find_vma() and is less error-prone.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-07 16:26:24 +11:00
Becky Bruce 1257a76547 powerpc: Enable hugetlb by default for corenet64 platforms
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-07 16:26:23 +11:00
Becky Bruce 41caebd123 powerpc: Enable Hugetlb by default for 32-bit 85xx/corenet
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-07 16:26:23 +11:00
Becky Bruce a475c8ecc6 powerpc: Kconfig updates for FSL BookE HUGETLB 64-bit
Allow hugetlb to be enabled on 64b FSL_BOOK3E.  No platforms enable
it by default yet.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-07 16:26:23 +11:00
Becky Bruce a6146888be powerpc: Add gpages reservation code for 64-bit FSL BOOKE
For 64-bit FSL_BOOKE implementations, gigantic pages need to be
reserved at boot time by the memblock code based on the command line.
This adds the call that handles the reservation, and fixes some code
comments.

It also removes the previous pr_err when reserve_hugetlb_gpages
is called on a system without hugetlb enabled - the way the code is
structured, the call is unconditional and the resulting error message
spurious and confusing.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-07 16:26:23 +11:00
Becky Bruce d1b9b12811 powerpc: Add hugepage support to 64-bit tablewalk code for FSL_BOOK3E
Before hugetlb, at each level of the table, we test for
!0 to determine if we have a valid table entry.  With hugetlb, this
compare becomes:
        < 0 is a normal entry
        0 is an invalid entry
        > 0 is huge

This works because the hugepage code pulls the top bit off the entry
(which for non-huge entries always has the top bit set) as an
indicator that we have a hugepage.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-07 16:26:22 +11:00
Becky Bruce 27609a42ee powerpc: Whitespace/comment changes to tlb_low_64e.S
I happened to comment this code while I was digging through it;
we might as well commit that.  I also made some whitespace
changes - the existing code had a lot of unnecessary newlines
that I found annoying when I was working on my tiny laptop.

No functional changes.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-07 16:26:22 +11:00
Becky Bruce 881fde1db5 powerpc: hugetlb: modify include usage for FSL BookE code
The original 32-bit hugetlb implementation used PPC64 vs PPC32 to
determine which code path to take.  However, the final hugetlb
implementation for 64-bit FSL ended up shared with the FSL
32-bit code so the actual check needs to be FSL_BOOK3E vs
everything else.  This patch changes the include protections to
reflect this.

There are also a couple of related comment fixes.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-07 16:26:22 +11:00
Becky Bruce a1cd541988 powerpc: Update hugetlb huge_pte_alloc and tablewalk code for FSL BOOKE
This updates the hugetlb page table code to handle 64-bit FSL_BOOKE.
The previous 32-bit work counted on the inner levels of the page table
collapsing.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-07 16:26:22 +11:00
Becky Bruce 8c1674de2b powerpc: Fix booke hugetlb preload code for PPC_MM_SLICES and 64-bit
This patch does 2 things: It corrects the code that determines the
size to write into MAS1 for the PPC_MM_SLICES case (this originally
came from David Gibson and I had incorrectly altered it), and it
changes the methodolody used to calculate the size for !PPC_MM_SLICES
to work for 64-bit as well as 32-bit.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-07 16:26:21 +11:00
Becky Bruce 97632e6fbe powerpc: hugetlb: fix huge_ptep_set_access_flags return value
There was an unconditional return of "1" in the original code
from David Gibson, and I dropped it because it wasn't needed
for FSL BOOKE 32-bit.  However, not all systems (including 64-bit
FSL BOOKE) do loading of the hpte from the fault handler asm
and depend on this function returning 1, which causes a call
to update_mmu_cache() that writes an entry into the tlb.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-07 16:26:21 +11:00
Becky Bruce 7651295944 powerpc: Only define HAVE_ARCH_HUGETLB_UNMAPPED_AREA if PPC_MM_SLICES
If we don't have slices, we should be able to use the generic
hugetlb_get_unmapped_area() code

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-07 16:26:21 +11:00
Kyle Moffett 09dc34a95b powerpc/mpic: Add in-core support for cascaded MPICs
The Cell and PowerMac platforms use virtually identical cascaded-IRQ
setup code, so just merge it into the core.  Ideally this code would
trigger automatically when an MPIC device-node specifies an "interrupts"
property, perhaps even enabling MPIC_SECONDARY along the way.

Unfortunately, Benjamin Herrenschmidt has had bad experiences in the
past with the quality of Apple PowerMac device-trees, so to be safe we
will only try to parse out an IRQ if the MPIC_SECONDARY flag is set by
the caller.

Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-07 13:43:09 +11:00
Kyle Moffett c51242e708 powerpc/mpic: Cache the device-tree node in "struct mpic"
Store the node pointer in the MPIC during initialization so that all of
the later operational code can just reuse the cached pointer.

Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-07 13:43:08 +11:00
Kyle Moffett c579bc766a powerpc/mpic: Put "pic-no-reset" test back into the MPIC code
There's not really any reason to have this one-liner in a separate
static inline function, given that all the other similar tests are
already in the alloc_mpic() code.

Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-07 13:43:08 +11:00
Kyle Moffett e62b760179 powerpc/mpic: Don't open-code dcr_resource_start
Don't open-code the OpenFirmware "dcr-reg" property lookup trying to map
DCR resources.  This makes the code a bit easier to read.

Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-07 13:43:08 +11:00
Kyle Moffett be8bec56df powerpc/mpic: Invert the meaning of MPIC_PRIMARY
It turns out that there are only 2 in-tree platforms which use MPICs
which are not "primary":  IBM Cell and PowerMac.  To reduce the
complexity of the typical board setup code, invert the MPIC_PRIMARY bit
into MPIC_SECONDARY.

Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-07 13:43:08 +11:00
Kyle Moffett 996983b75c powerpc/mpic: Search for open-pic device-tree node if NULL
Almost all PowerPC platforms use a standard "open-pic" device node so
the mpic_alloc() function now accepts NULL for the device-node.  This
will cause it to perform a default search with of_find_matching_node().

Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-07 13:43:07 +11:00
Kyle Moffett e7a98675ca powerpc/mpic: Save computed phys_addr for board-specific code
The MPIC code can already perform an automatic OF address translation
step as part of mpic_alloc(), but several boards need to use that base
address when they perform mpic_assign_isu().

The easiest solution is to save the computed physical address into the
"struct mpic" for later use by the board code.

Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-07 13:43:07 +11:00
Kyle Moffett 5bdb6f2e58 powerpc/mpic: Assume a device-node was passed in mpic_alloc()
All of the existing callers of mpic_alloc() pass in a non-NULL
device-node pointer, so the checks for a NULL device-node may be
removed.

Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-07 13:43:07 +11:00
Kyle Moffett 8bf4156896 powerpc: Consolidate mpic_alloc() OF address translation
Instead of using the open-coded "reg" property lookup and address
translation in mpic_alloc(), directly call of_address_to_resource().
This includes various workarounds for special cases which the naive
of_address_translate() does not.

Afterwards it is possible to remove the copiously copy-pasted calls to
of_address_translate() from the 85xx/86xx/powermac platforms.

Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-07 13:43:06 +11:00
Kyle Moffett 582d3e0994 powerpc/85xx: Move mpc85xx_smp_init() decl to a new "smp.h"
This removes a bunch of "extern" declarations and CONFIG_SMP ifdefs.

Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-07 13:43:06 +11:00
David S. Miller b3613118eb Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net 2011-12-02 13:49:21 -05:00
Justin P. Mattock 42b2aa86c6 treewide: Fix typos in various parts of the kernel, and fix some comments.
The below patch fixes some typos in various parts of the kernel, as well as fixes some comments.
Please let me know if I missed anything, and I will try to get it changed and resent.

Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-12-02 14:57:31 +01:00
Wolfgang Grandegger fa17a019c8 powerpc: tqm8548/tqm8xx: add and update CAN device nodes
This patch enables or updates support for the CC770 and AN82527
CAN controller on the TQM8548 and TQM8xx boards.

CC: devicetree-discuss@lists.ozlabs.org
CC: linuxppc-dev@ozlabs.org
CC: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-01 13:09:32 -05:00
Tanmay Inamdar d5b9ee7b51 powerpc/40x: Add APM8018X SOC support
The AppliedMicro APM8018X embedded processor targets embedded applications that
require low power and a small footprint. It features a PowerPC 405 processor
core built in a 65nm low-power CMOS process with a five-stage pipeline executing
up to one instruction per cycle. The family has 128-kbytes of on-chip memory,
a 128-bit local bus and on-chip DDR2 SDRAM controller with 16-bit interface.

Signed-off-by: Tanmay Inamdar <tinamdar@apm.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
2011-11-30 10:02:15 -05:00
Michael S. Tsirkin 335b8cf7c3 powerpc: switch to GENERIC_PCI_IOMAP
powerpc copied pci_iomap from generic code, probably to avoid
pulling the rest of iomap.c in.  Since that's in
a separate file now, we can reuse the common implementation.

The only difference is handling of nocache flag,
that turns out to be done correctly by the
generic code since arch/powerpc/include/asm/io.h
defines ioremap_nocache same as ioremap.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
2011-11-28 21:13:18 +02:00
Tejun Heo d4bbf7e775 Merge branch 'master' into x86/memblock
Conflicts & resolutions:

* arch/x86/xen/setup.c

	dc91c728fd "xen: allow extra memory to be in multiple regions"
	24aa07882b "memblock, x86: Replace memblock_x86_reserve/free..."

	conflicted on xen_add_extra_mem() updates.  The resolution is
	trivial as the latter just want to replace
	memblock_x86_reserve_range() with memblock_reserve().

* drivers/pci/intel-iommu.c

	166e9278a3 "x86/ia64: intel-iommu: move to drivers/iommu/"
	5dfe8660a3 "bootmem: Replace work_with_active_regions() with..."

	conflicted as the former moved the file under drivers/iommu/.
	Resolved by applying the chnages from the latter on the moved
	file.

* mm/Kconfig

	6661672053 "memblock: add NO_BOOTMEM config symbol"
	c378ddd53f "memblock, x86: Make ARCH_DISCARD_MEMBLOCK a config option"

	conflicted trivially.  Both added config options.  Just
	letting both add their own options resolves the conflict.

* mm/memblock.c

	d1f0ece6cd "mm/memblock.c: small function definition fixes"
	ed7b56a799 "memblock: Remove memblock_memory_can_coalesce()"

	confliected.  The former updates function removed by the
	latter.  Resolution is trivial.

Signed-off-by: Tejun Heo <tj@kernel.org>
2011-11-28 09:46:22 -08:00
Dan McGee fa8cbaaf5a powerpc+sparc64/mm: Remove hack in mmap randomize layout
Since commit 8a0a9bd4db, this comment in mmap_rnd() does not
hold true as the value returned by get_random_int() will in fact be

different every single call. Remove the comment and simplify the code
back to its original desired form.

This reverts commit a5adc91a4b which is no longer necessary and
also fixes the sparc code that copied this same adjustment.

Signed-off-by: Dan McGee <dpmcgee@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-28 11:42:09 +11:00
Anton Blanchard 3ce21cdfe9 powerpc/xics: Harden xics hypervisor backend
During kdump stress testing I sometimes see the kdump kernel panic
with:

  Interrupt 0x306 (real) is invalid, disabling it.
  Kernel panic - not syncing: bad return code EOI - rc = -4, value=ff000306

Instead of panicing print the error message, dump the stack the first
time it happens and continue on. Add some more information to the
debug messages as well.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-28 11:42:09 +11:00
Anton Blanchard 3bfd0c9c8f powerpc: Decode correct MSR bits in oops output
On a 64bit book3s machine I have an oops from a system reset that
claims the book3e CE bit was set:

MSR: 8000000000021032 <ME,CE,IR,DR>  CR: 24004082  XER: 00000010

On a book3s machine system reset sets IBM bit 46 and 47 depending on
the power saving mode. Separate the definitions by type and for
completeness add the rest of the bits in.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-28 11:42:09 +11:00
Matthew McClintock e1fc235d74 arch/powerpc: Remove duplicate/redundant Altivec entries
In lieu of having multiple similiar lines, we can just have one
generic cpu-as line for CONFIG_ALTIVEC

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-28 11:42:09 +11:00
Dmitry Eremin-Solenikov f49a0c9c64 powerpc/maple: Enable access to HT Host-Bridge on Maple
CPC925/CPC945 use special window to access host bridge functionality of
u3-ht. Provide a way to access this device.

Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-28 11:42:08 +11:00
sukadev@linux.vnet.ibm.com 1d54cf2b97 powerpc: Implement CONFIG_STRICT_DEVMEM
As described in the help text in the patch, this token restricts general
access to /dev/mem as a way of increasing the security. Specifically, access
to exclusive IOMEM and kernel RAM is denied unless CONFIG_STRICT_DEVMEM is
set to 'n'.

Implement the 'devmem_is_allowed()' interface for Powerpc. It will be
called from range_is_allowed() when userpsace attempts to access /dev/mem.

This patch is based on an earlier patch from Steve Best and with input from
Paul Mackerras and Scott Wood.

[BenH] Fixed a typo or two and removed the generic change which should
       be submitted as a separate patch

Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-28 11:42:08 +11:00
Benjamin Herrenschmidt 56368797d6 Merge remote-tracking branch 'kumar/next' into next 2011-11-25 15:25:39 +11:00
Justin P. Mattock e075cd7001 powerpc/mpic: Remove extra semicolon.
The patch below removes an extra semicolon.

Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
CC: linuxppc-dev@lists.ozlabs.org
CC: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-25 14:53:25 +11:00
Ananth N Mavinakayanahalli 595fe91447 powerpc: Export PIR data through sysfs
On Fri, Nov 11, 2011 at 10:17:55AM +0530, Ananth N Mavinakayanahalli wrote:
> >
> > At this rate we're going to end up with no bits left for CPU features
> > way too quickly... Especially for something we only care about once at
> > boot time.
> >
> > Wouldn't CPU_FTR_PPCAS_ARCH_V2 be a good enough test ?
>
> /me checks Cell manuals... yes, that test would be good enough. I will
> cook up a patch to use this.

Here it is...

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-25 14:53:23 +11:00
Benjamin Herrenschmidt 184cd4a3b9 powerpc/powernv: PCI support for p7IOC under OPAL v2
This adds support for p7IOC (and possibly other IODA v1 IO Hubs)
using OPAL v2 interfaces.

We completely take over resource assignment and assign them using an
algorithm that hands out device BARs in a way that makes them fit in
individual segments of the M32 window of the bridge, which enables us
to assign individual PEs to devices and functions.

The current implementation gives out a PE per functions on PCIe, and a
PE for the entire bridge for PCIe to PCI-X bridges.

This can be adjusted / fine tuned later.

We also setup DMA resources (32-bit only for now) and MSIs (both 32-bit
and 64-bit MSI are supported).

The DMA allocation tries to divide the available 256M segments of the
32-bit DMA address space "fairly" among PEs. This is done using a
"weight" heuristic which assigns less value to things like OHCI USB
controllers than, for example SCSI RAID controllers. This algorithm
will probably want some fine tuning for specific devices or device
types.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-25 14:53:15 +11:00
Benjamin Herrenschmidt ca45cfe31e powerpc/powernv: Fixup p7ioc PCIe root complex class code
It advertises "host bridge" instead of "PCI to PCI bridge" which confuses
the Linux probe code.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-25 14:32:59 +11:00
Benjamin Herrenschmidt 1f1616e864 powerpc/powernv: Add TCE SW invalidation support
This is used for newer IO Hubs such as p7IOC.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-25 14:32:57 +11:00
Benjamin Herrenschmidt 48c2ce97fa powerpc/pci: Change how re-assigning resouces work
When PCI_REASSIGN_ALL_RSRC is set, we used to clear all bus resources
at the beginning of survey and re-allocate them later.

This changes it so instead, during early fixup, we mark all resources
as IORESOURCE_UNSET and move them down to be 0-based.

Later, if bus resources are still unset at the beginning of the survey,
then we clear them.

This shouldn't impact the re-assignment case on 4xx, but will enable
us to have the platform do some custom resource assignment before the
survey, by clearing individual resources IORESOURCE_UNSET bit.

Also limits the clutter in the kernel log from fixup when re-assigning
since we don't care about the offset applied to the BAR values in this
case.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-25 14:32:55 +11:00
Benjamin Herrenschmidt 491b98c315 powerpc/pci: Add a platform hook after probe and before resource survey
Some platforms need to perform resource allocation using a custom algorithm
due to HW constraints, or may want to tweak things globally below a host
bridge. For example OPAL support for IODA will need to perform a
resource allocation pass that applies IODA specific segmentation
constraints to MMIO which cannot be done simply using the kernel generic
resource management code.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-25 14:32:53 +11:00
Geoff Thorpe 09c188c4f6 powerpc: Add pgprot_cached_noncoherent()
This adds a pgprot combination required by some cache-enabled IO device
mappings, such as Freescale datapath (QMan and BMan) portals.

Signed-off-by: Geoff Thorpe <geoff@geoffthorpe.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-25 14:32:52 +11:00
Thomas Gleixner e8d2c47352 powerpc: Allow irq threading
All interrupts which must be non threaded are marked
IRQF_NO_THREAD. So it's safe to allow force threaded handlers.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-25 14:14:38 +11:00
Thomas Gleixner 3b5e16d7ad powerpc: Mark IPI interrupts IRQF_NO_THREAD
IPI handlers cannot be threaded. Remove the obsolete IRQF_DISABLED
flag (see commit e58aa3d2) while at it.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-25 14:14:38 +11:00
Thomas Gleixner 5f20b85dc2 powerpc/wsp: Mark opb cascade handler IRQF_NO_THREAD
Cascade handlers must run in hard interrupt context.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-25 14:11:29 +11:00
Thomas Gleixner c6c56bdda1 powerpc/85xx: Mark cascade irq IRQF_NO_THREAD
Cascade interrupt must run in hard interrupt context.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-25 14:11:29 +11:00
Ravi K. Nittala df17f56d8a powerpc/pseries: Cancel RTAS event scan before firmware flash
The RTAS firmware flash update is conducted using an RTAS call that is
serialized by lock_rtas() which uses spin_lock. While the flash is in
progress, rtasd performs scan for any RTAS events that are generated by
the system. rtasd keeps scanning for the RTAS events generated on the
machine. This is performed via workqueue mechanism. The rtas_event_scan()
also uses an RTAS call to scan the events, eventually trying to acquire
the spin_lock before issuing the request.

The flash update takes a while to complete and during this time, any other
RTAS call has to wait. In this case, rtas_event_scan() waits for a long time
on the spin_lock resulting in a soft lockup.

Fix: Just before the flash update is performed, the queued rtas_event_scan()
work item is cancelled from the work queue so that there is no other RTAS
call issued while the flash is in progress. After the flash completes, the
system reboots and the rtas_event_scan() is rescheduled.

Signed-off-by: Suzuki Poulose <suzuki@in.ibm.com>
Signed-off-by: Ravi Nittala <ravi.nittala@in.ibm.com>
Reported-by: Divya Vikas <divya.vikas@in.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-25 14:11:29 +11:00
Jimi Xenidis cc35b67668 powerpc/book3e: Add Chroma as a new WSP/PowerEN platform.
This patch add the Chroma platform to WSP/PowerEN, which is a PCIe
card (a defconfig is included).

The card includes an H8 service processor that is used to manage the
card.  The H8 is connected over the second serial UART on the PowerEN
chip so this patch includes a simple 16550 driver to enable
communication, mostly for "power off" and "rebooting".

This patch also includes a, WSP specific, "halt" method that will shut
of all A2 cores but still leave power on at the chip level.  This is
desirable, especially if you wish to interrogate the chip with a
hardware probe after the halt.

Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-25 14:11:29 +11:00
Jimi Xenidis 08f6d6abc3 powerpc/xmon: Fix #if typo for systems without MSR[RI]
Sorry, there was a typo in the #if

signed-off-by: Jimi Xenidis <jimix@pobox.com>

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-25 14:11:28 +11:00
Jimi Xenidis 79873e8df6 powerpc/xmon: Fix the 'u' command description
The 'u' command will print the TLB on book3e parts and the SLB on
Book3s parts, but the help system doesn't say that correctly.

Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-25 14:11:28 +11:00
Jimi Xenidis c3dcf53a3f powerpc/icswx: Simple ACOP fault handler
This patch adds a fault handler that responds to illegal Coprocessor
types.  Currently all CTs are treated and illegal.  There are two ways
to report the fault back to the application.  If the application used
the record form ("icswx.") then the architected "reject" is emulated.
If the application did not used the record form ("icswx") then it is
selectable by config whether the failure is silent (as architected) or
a SIGILL is generated.

In all cases pr_warn() is used to log the bad CT.

Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-25 14:11:28 +11:00
Jimi Xenidis fac26ad4f9 powerpc/book3e: Add ICSWX/ACOP support to Book3e cores like A2
ICSWX is also used by the A2 processor to access coprocessors,
although not all "chips" that contain A2s have coprocessors.

Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-25 14:11:28 +11:00
Jimi Xenidis 9d67028090 powerpc: Split ICSWX ACOP and PID processing
Some processors, like embedded, that already have a PID register that
is managed by the system.  This patch separates the ACOP and PID
processing into separate files so that the ACOP code can be shared.

Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-25 14:11:27 +11:00
Julia Lawall 3631cb83dd powerpc/powermac: Add missing of_node_put
np is initialized to the result of calling a function that calls
of_node_get, so of_node_put should be called before the pointer is dropped.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression e,e1,e2;
@@

* e = \(of_find_node_by_type\|of_find_node_by_name\)(...)
  ... when != of_node_put(e)
      when != true e == NULL
      when != e2 = e
  e = e1
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-25 14:11:27 +11:00
Julia Lawall dbfc189cc5 powerpc/cell/iommu: Add missing of_node_put
np is initialized to the result of calling a function that calls
of_node_get, so of_node_put should be called before the pointer is dropped.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression e,e1,e2;
@@

* e = \(of_find_node_by_type\|of_find_node_by_name\)(...)
  ... when != of_node_put(e)
      when != true e == NULL
      when != e2 = e
  e = e1
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-25 14:11:27 +11:00
Milton Miller 8d3d589a79 powerpc/pseries: Software invalidatation of TCEs
Some pseries IOMMUs cache TCEs but don't snoop when the TCEs are changed
in memory, hence we need manually invalidate in software.

This adds code to do the invalidate.  It keys off a device tree property
to say where the to do the MMIO for the invalidate and some information
on what the format of the invalidate including some magic routing info.

it_busno get overloaded with this magic routing info and it_index with
the MMIO address for the invalidate command.

This then gets hooked into the building and freeing of TCEs.

This is only useful on bare metal pseries.  pHyp takes care of this when
virtualised.

Based on patch from Milton with cleanups from Mikey.

Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-25 14:11:26 +11:00
Anton Blanchard 7df1027542 powerpc/time: Optimise decrementer_check_overflow
decrementer_check_overflow is called from arch_local_irq_restore so
we want to make it as light weight as possible. As such, turn
decrementer_check_overflow into an inline function.

To avoid a circular mess of includes, separate out the two components
of struct decrementer_clock and keep the struct clock_event_device
part local to time.c.

The fast path improves from:

arch_local_irq_restore
     0:       mflr    r0
     4:       std     r0,16(r1)
     8:       stdu    r1,-112(r1)
     c:       stb     r3,578(r13)
    10:       cmpdi   cr7,r3,0
    14:       beq-    cr7,24 <.arch_local_irq_restore+0x24>
...
    24:       addi    r1,r1,112
    28:       ld      r0,16(r1)
    2c:       mtlr    r0
    30:       blr

to:

arch_local_irq_restore
    0:       std     r30,-16(r1)
    4:       ld      r30,0(r2)
    8:       stb     r3,578(r13)
    c:       cmpdi   cr7,r3,0
   10:       beq-    cr7,6c <.arch_local_irq_restore+0x6c>
...
   6c:       ld      r30,-16(r1)
   70:       blr

Unfortunately we still setup a local TOC (due to -mminimal-toc). Yet
another sign we should be moving to -mcmodel=medium.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-25 14:11:26 +11:00
Anton Blanchard 621692cb7e powerpc/time: Fix some style issues
Fix some formatting issues and use the DECREMENTER_MAX
define instead of 0x7fffffff.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-25 14:10:00 +11:00
Anton Blanchard 68568add2c powerpc/time: Remove unnecessary sanity check of decrementer expiration
The clockevents code uses max_delta_ns to avoid calling a
clockevent with too large a value.

Remove the redundant version of this in the timer_interrupt
code.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-25 14:09:59 +11:00
Anton Blanchard 11b8633ada powerpc/time: Use clocksource_register_hz
Use clocksource_register_hz which calculates the shift/mult
factors for us. Also remove the shift = 22 assumption in
vsyscall_update - thanks to Paul Mackerras and John Stultz for
catching that.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-25 14:09:59 +11:00
Anton Blanchard d8afc6fd95 powerpc/time: Use clockevents_calc_mult_shift
We can use clockevents_calc_mult_shift instead of doing all
the work ourselves.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-25 14:09:59 +11:00
Anton Blanchard 37fb9a0231 powerpc/time: Handle wrapping of decrementer
When re-enabling interrupts we have code to handle edge sensitive
decrementers by resetting the decrementer to 1 whenever it is negative.
If interrupts were disabled long enough that the decrementer wrapped to
positive we do nothing. This means interrupts can be delayed for a long
time until it finally goes negative again.

While we hope interrupts are never be disabled long enough for the
decrementer to go positive, we have a very good test team that can
drive any kernel into the ground. The softlockup data we get back
from these fails could be seconds in the future, completely missing
the cause of the lockup.

We already keep track of the timebase of the next event so use that
to work out if we should trigger a decrementer exception.

Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-25 14:09:58 +11:00
Tony Breeds 49e44064d7 powerpc/44x: Add mtd ndfc to the ppx44x defconfig
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Acked-by: Josh Boyer <jwboyer@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-25 10:06:00 +11:00
Kumar Gala 13020be8be powerpc: Fix compiliation with hugetlbfs enabled
arch/powerpc/mm/hugetlbpage.c: In function 'reserve_hugetlb_gpages':
arch/powerpc/mm/hugetlbpage.c:312:2: error: implicit declaration of function 'parse_args'

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-25 10:05:59 +11:00
Michael S. Tsirkin 4673ca8eb3 lib: move GENERIC_IOMAP to lib/Kconfig
define GENERIC_IOMAP in a central location
instead of all architectures. This will be helpful
for the follow-up patch which makes it select
other configs. Code is also a bit shorter this way.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
2011-11-24 22:21:19 +02:00
Timur Tabi 895d603f94 powerpc/fsl_msi: add support for the fsl, msi property in PCI nodes
On Freescale parts with multiple MSI controllers, the controllers are
combined into one "pool" of interrupts.  Whenever a device requests an MSI
interrupt, the next available interrupt from the pool is selected,
regardless of which MSI controller the interrupt is from.  This works
because each PCI bus has an ATMU to all of CCSR, so any PCI device can
access any MSI interrupt register.

The fsl,msi property is used to specify that a given PCI bus should only
use a specific MSI device.  This is necessary, for example, with the
Freescale hypervisor, because the MSI devices are assigned to specific
partitions.

Ideally, we'd like to be able to assign MSI devices to PCI busses within
the MSI or PCI layers.  However, there does not appear to be a mechanism
to do that.  Whenever the MSI layer wants to allocate an MSI interrupt to
a PCI device, it just calls arch_setup_msi_irqs().  It would be nice if we
could register an MSI device with a specific PCI bus.

So instead we remember the phandles of each MSI device, and we use that to
limit our search for an available interrupt.  Whenever we are asked to
allocate a new interrupt for a PCI device, we check the fsl,msi property
of the PCI bus for that device.  If it exists, then as we are looping over
all MSI devices, we skip the ones that don't have a matching phandle.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:41 -06:00
Kumar Gala db9c187091 powerpc/85xx: Renamed mpc85xx_common.c to common.c
The file name is already scoped by the directory its in.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:41 -06:00
Kumar Gala 199bfbe6f5 powerpc/85xx: Additional consolidate of_platform_bus_probe calls
P1010RDB & P1023RDS can use the new mpc85xx_common_publish_devices().
Also move 'fsl,srio' into the list of standard buses.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:41 -06:00
Dmitry Eremin-Solenikov 46d026ac10 powerpc/85xx: consolidate of_platform_bus_probe calls
85xx board files have a lot of duplication in *_publish_devices()/
*_declare_of_platform_devices() functions. Merge that into a single
function common to most of the boards.

Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:41 -06:00
Dmitry Eremin-Solenikov 543a07b173 powerpc/85xx: separate cpm2 pic init
Separate handling of CPM2 PIC initialization to mpc85xx_cpm2_pic_init()
function.

Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:41 -06:00
Dmitry Eremin-Solenikov 5d71349580 powerpc/83xx: make mpc830x_rdb use mpc83xx_setup_pci
Traditionally mpc830x_rdb board file searched for mpc8308-pcie devices.
However both in-kernel dts from the beginning declared those pcie units
as compatible with mpc8314-pci, which is handled by mpc83xx_setup_pci().

Drop special handling for mpc8308 and use common function instead.

Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:41 -06:00
Dmitry Eremin-Solenikov bede480d45 powerpc/83xx: merge PCI bridge additions
Nearly all mpc83xx-based boards have a common piece of code - one that
loops over all pci/pcie bridges and registers them. Merge that code into
a special function common to all boards.

Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:40 -06:00
Dmitry Eremin-Solenikov 7669d58c66 powerpc/83xx: consolidate of_platform_bus_probe calls
83xx board files have a lot of duplication in
*_declare_of_platform_devices() functions. Merge that into a single
function common to most of the boards.

The only leftover is mpc834x_itx.c board file which explicitly asks for
fsl,pq2pro-localbus, as corresponding bindings don't provide
"simple-bus" compatibility in localbus node.

Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:40 -06:00
Dmitry Eremin-Solenikov d4fb5ebd83 powerpc/83xx: consolidate init_IRQ functions
On mpc83xx platform nearly all _init_IRQ functions look alike. They either
just setup ipic, or setup ipic and QE PIC. Separate this to special functions
to be either referenced from ppc_md, or called from board file.

Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:40 -06:00
Timur Tabi c0019a4d67 powerpc/85xx: add pixis indirect mode device tree node
The Freescale P1022 has a unique pin muxing "feature" where the DIU video
controller's video signals are muxed with 24 of the local bus address signals.
When the DIU is enabled, the bulk of the local bus is disabled, preventing
access to memory-mapped devices like NOR flash and the pixis FPGA.

In this situation, the pixis supports "indirect mode", which allows access
to the pixis itself by reading/writing addresses on specific local bus
chip selects.  CS0 is used to select which pixis register to access, and
CS1 is used to read/write the value.

To support this, we introduce another board-control child node of the
localbus node that contains a 'reg' property for CS0 and CS1.  This will
produce the correct physical addresses for CS0 and CS1.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:40 -06:00
Jia Hongtao 09cef8bd07 powerpc/85xx: Add lbc suspend support for PM
Power supply for LBC registers is off when system go to deep-sleep state.
We save the values of registers before suspend and restore to registers
after resume.

We removed the last two reservation arrays from struct fsl_lbc_regs for
allocating less memory and minimizing the memcpy size.

Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:40 -06:00
Jason Jin 05737c7c5b powerpc/fsl-pci: Don't hide resource for pci/e when configured as Agent/EP
Current pci/pcie init code will hide the pci/pcie host resource.
But did not judge it is host/RC or agent/EP. If configured as
agent/EP, we should avoid hiding its resource in the host side.

In PCI system, the Programing Interface can be used to judge the
host/agent status:
Programing Interface = 0: host
Programing Interface = 1: Agent

In PCIE system, both the Programing Interface and Header type can
be used to judge the RC/EP status.
Header Type = 0: EP
Header Type = 1: RC

Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:40 -06:00
Kumar Gala 54986964c1 powerpc/85xx: Update SRIO device tree nodes
Update all dts files that support SRIO controllers to match the new
fsl,srio device tree binding.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:39 -06:00
Kumar Gala 03f4201bd4 powerpc/85xx: Rework P5020DS device tree
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p5020-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
* Removed mpic interrupt-parent from sec nodes, just use top level

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:39 -06:00
Kumar Gala b9db022c62 powerpc/85xx: Rework P4080DS device trees
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p4080-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
* Removed mpic interrupt-parent from sec nodes, just use top level

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:39 -06:00
Kumar Gala 8389c823b5 powerpc/85xx: Rework P3060QDS device tree
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p3060-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
* Removed mpic interrupt-parent from sec nodes, just use top level
* Fixed l3-cache IRQs, we have 2 CPCs, so we should have IRQs for both

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:39 -06:00
Kumar Gala b4c3804d18 powerpc/85xx: Rework P3041DS device tree
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p3041-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
* Fixed some dcsr compatiable typo's from 'p43041' to 'p3041'

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:39 -06:00
Kumar Gala 8b8673b850 powerpc/85xx: Rework P2041RDB device tree
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p2041-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:39 -06:00
Kumar Gala 941d71c736 powerpc/85xx: Rework P2020RDB device tree
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:

* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Reworked PCIe nodes to allow supportin IRQs for controller (errors) and
  moved PCI device IRQs down to virtual bridge level
* Updated spi node to new espi binding specification
* Renamed 'sdhci' node to 'sdhc'
* Changed GPIO compatiable from 'fsl,mpc8572-gpio' to 'fsl,pq3-gpio' as the
 'mpc8572' compatiable is to deal with a 'mpc8572' specific to an erratum
* Fixed wrong reg offsets for mdio nodes associated with etsec2 &
* etsec3
* Dropping "fsl,p2020-IP..." from compatibles for standard blocks

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:38 -06:00
Kumar Gala 7f9ce7143e powerpc/85xx: Rework P2020DS device tree
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:

* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
  and moved PCI device IRQs down to virtual bridge level
* Updated spi node to new espi binding specification
* Renamed 'sdhci' node to 'sdhc'
* Changed GPIO compatiable from 'fsl,mpc8572-gpio' to 'fsl,pq3-gpio' as the
 'mpc8572' compatiable is to deal with a 'mpc8572' specific to an erratum
* Fixed wrong reg offsets for mdio nodes associated with etsec2 & etsec3
* Dropping "fsl,p2020-IP..." from compatibles for standard blocks

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:38 -06:00
Kumar Gala b0e2f248b4 powerpc/85xx: Rework P1023RDS device tree
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Dropping "fsl,p1023-IP..." from compatibles for standard blocks
* Removed incorrect power/pmc node, there are no etsec on P1023

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:38 -06:00
Kumar Gala ab827d97bd powerpc/85xx: Rework P1022DS device tree
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:

* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
  and moved PCI device IRQs down to virtual bridge level
* Changed GPIO compatiable from 'fsl,mpc8572-gpio' to 'fsl,pq3-gpio' as the
  'mpc8572' compatiable is to deal with a 'mpc8572' specific to an erratum
* Updated spi node to new espi binding specification
* Renamed SDHC node from 'sdhci' to 'sdhc'
* Added usb node for 2nd usb controller
* Dropping "fsl,p1022-IP..." from compatibles for standard blocks
* Fixed bug in local bus range node for CS2, was maping to
  0x0 0x0xffa00000 instead of 0xf 0xffa00000
* Fixed localbus reg property should have been 0xf 0xffe05000

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Tested-by: Timur Tabi <timur@freescale.com>
2011-11-24 02:01:38 -06:00
Kumar Gala ffeb33d20c powerpc/85xx: Rework P1021MDS device tree
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:

* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Reworked PCIe nodes to allow supportin IRQs for controller (errors) and
  moved PCI device IRQs down to virtual bridge level
* Renamed SDHC node from 'sdhci' to 'sdhc'
* Added usb node for 2nd usb controller
* Dropping "fsl,p1021-IP..." from compatibles for standard blocks

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:38 -06:00
Kumar Gala 3316a83c7c powerpc/85xx: Add P1020RDB 36-bit address map device tree
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:38 -06:00
Kumar Gala 4e36afa7c5 powerpc/85xx: Rework P1020RDB device tree
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:
* Dropping "fsl,p1020-IP..." from compatibles for standard blocks
* Fixed PCIe interrupt-maps to have proper number of cells
* Added mdio node for etsec@26000
* Added usb node for 2nd usb controller

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:37 -06:00
Kumar Gala 4de0e39cb8 powerpc/85xx: Add a P1010RDB 36-bit address map device tree
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:37 -06:00
Kumar Gala 396a5a5691 powerpc/85xx: Add crypto engine to P1010 SoC device tree
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:37 -06:00
Kumar Gala ae744b4118 powerpc/85xx: Add RTC to P1010RDB device tree
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:37 -06:00
Kumar Gala 96488746bb powerpc/85xx: Rework P1010RDB and P1010 device tree
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Dropping "fsl,p1010-IP..." from compatibles for standard blocks
* PCI interrupt map - wrong IRQs for PCI-0 controller
* SDHC interrupt sense was wrong

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:37 -06:00
Kumar Gala 532919592f powerpc/85xx: Rework MPC8572DS device tree
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:

* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Removed CPU properties setup by u-boot to match other .dts
* Reworked PCIe nodes to allow supportin IRQs for controller (errors) and
  moved PCI device IRQs down to virtual bridge level
* Moved mdio nodes up one level instead of under tsec nodes
* Added GPIO controller node to MPC8572 SoC template
* Dropping "fsl,mpc8572-IP..." from compatibles for standard blocks

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:37 -06:00
Kumar Gala e7a7b329f2 powerpc/85xx: Rework MPC8569MDS device tree
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:
* Moved to a standard 2 #address-cells & #size-cells at top-level
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Removed CPU properties setup by u-boot to match other .dts
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
  and moved PCI device IRQs down to virtual bridge level
* Renamed SDHC node from 'sdhci' to 'sdhc'
* Dropping "fsl,mpc8569-IP..." from compatibles for standard blocks

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:36 -06:00
Kumar Gala 1a23b4a64a powerpc/85xx: Rework MPC8568MDS device tree
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:
* Moved to a standard 2 #address-cells & #size-cells at top-level
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Removed CPU properties setup by u-boot to match other .dts
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
  and moved PCI device IRQs down to virtual bridge level
* Dropping "fsl,mpc8568-IP..." from compatibles for standard blocks

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:36 -06:00
Kumar Gala 53e23dcb18 powerpc/85xx: Rework MPC8548CDS device trees
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:
* Moved to a standard 2 #address-cells & #size-cells at top-level
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Moved mdio nodes up one level instead of under tsec nodes
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
  and moved PCI device IRQs down to virtual bridge level
* Removed CPU properties setup by u-boot to match other .dts
* Added localbus node, but no chipselect details at this point
* Added MPIC / PCIe msi node
* Dropping "fsl,mpc8548-IP..." from compatibles for standard blocks

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:36 -06:00
Kumar Gala b7f817547d powerpc/85xx: Rework MPC8544DS device tree
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:
* Moved to a standard 2 #address-cells & #size-cells at top-level
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Removed CPU properties setup by u-boot to match other .dts
* Added localbus node, but no chipselect details at this point
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
  and moved PCI device IRQs down to virtual bridge level
* Moved mdio nodes up one level instead of under tsec nodes
* Updated ethernet 'model' to 'eTSEC' as that's what on MPC8544
* Dropping "fsl,mpc8544-IP..." from compatibles for standard blocks

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:36 -06:00
Kumar Gala 2e8685a491 powerpc/85xx: Rework MPC8536DS device trees
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Added localbus node, but no chipselect details at this point
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
* and moved
  PCI device IRQs down to virtual bridge level
* Moved mdio nodes up one level instead of under tsec nodes
* Added GPIO controller node to MPC8536 SoC template
  [ marked as MPC8572 compatiable to get errata handling that applies ]
* Added missing cache-line-size & cache-size properties missing from
  L2-cache node
* Added IP level IEEE 1588 / ptp timer node

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:36 -06:00
Kumar Gala 5652520000 powerpc/85xx: create dts components to build up an SoC
Introduce some common components that we can utilize to build up the
various PQ3/85xx device trees.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:36 -06:00
Kumar Gala ce63873113 powerpc/85xx: p1020si.dtsi update interrupt handling
* set interrupt-parent at root so its not duplicate in every node
* Add mpic timers
* Move to 4-prop cells for mpic timer

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:35 -06:00
Kumar Gala a45edbf9dc powerpc/85xx: Add ethernet magic packet property to P1020 device tree
All eTSEC2 controllers support waking on magic packet so fixup device
tree to report that.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:35 -06:00
Kumar Gala 43cfddc3d9 powerpc/85xx: Update P1020 SEC3.3 node to match actual SoC HW
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:35 -06:00
Kumar Gala 38b8f1687f powerpc/85xx: Update SPI binding to match binding spec for P1020RDB
The SPI node is out of date with regards to the binding for fsl-espi and
driver support.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:35 -06:00
Kumar Gala fc2478e728 powerpc/85xx: Rework PCI nodes on P1020RDB
* Move SoC specific details like irq mapping to SoC dtsi
* Update interrupt property to cover both error interrupt and PCIe
  runtime interrupts

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:35 -06:00
Kumar Gala 1e6a9d04c2 powerpc/85xx: Simplify P1020RDB CAMP dts using includes
If we include the p1020rdb.dts instead of p1020si.dts we greatly reduce
duplication and maintenance.  We can just list which devices are
disabled for the given core and mpic protected sources.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:35 -06:00
Kai Jiang 077200cb5a powerpc/8xxx: Update device tree bus probe for new RapidIO node binding
Update of_platform_bus_probe() RapidIO node to be compitable with
new RapidIO dts compatible property.

Signed-off-by: Kai Jiang <Kai.Jiang@freescale.com>
Acked-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:34 -06:00
Liu Gang abc3aeae3a fsl-rio: Add two ports and rapidio message units support
Usually, freescale rapidio endpoint can support one or two 1x or 4X
LP-Serial link interfaces, and rapidio message transactions can be
implemented by two message units. This adds the support of two
rapidio ports and initializes message unit 0 and message unit 1. And
these ports and message units can work simultaneously.

Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Acked-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:34 -06:00
Liu Gang 6ec4bedbf1 fsl-rio: Split rio driver into two parts, RapidIO endpoint and message unit
The Freescale PowerPC RapidIO controller consists of a RapidIO endpoint and
a RapidIO message unit(RMU). Or use RapidIO message manager(RMan) to
replace the RMU in DPAA architecture. Therefore, we should split the code
into two function modules according to the hardware architecture. Add new
struct for RMU module, and new initialization function to set up RMU
module. This policy is very conducive to adding new module like RMan, or
adding multi-ports or message units support.

Signed-off-by: Lian Minghuan <Minghuan.Lian@freescale.com>
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Acked-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:34 -06:00
Julia Lawall e3854b6e25 arch/powerpc/sysdev/ehv_pic.c: add missing kfree
At this point, ehv_pic has been allocated but not stored anywhere, so it
should be freed before leaving the function.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@exists@
local idexpression x;
statement S,S1;
expression E;
identifier fl;
expression *ptr != NULL;
@@

x = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
     when != if (...) { <+...kfree(x)...+> }
     when any
     when != true x == NULL
x->fl
...>
(
if (x == NULL) S1
|
if (...) { ... when != x
               when forall
(
 return \(0\|<+...x...+>\|ptr\);
|
* return ...;
)
}
)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:24 -06:00
Alexandre Rusev 7145cf1209 powerpc/fsl-lbc: Fix for fsl_upm
If Freescale LBC driver fails to initialise itself from device tree, then
internal structure is freed only but not NULL-fied.  As result functions
fsl_lbc_find() after checking the structure is not NULL are trying to
access device registers.

Signed-off-by: Alexandre Rusev <arusev@dev.rtsoft.ru>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:00:42 -06:00
Joakim Tjernlund ae5f8c1982 powerpc/qe: Fixup QE_General4 errata
QE_General4 should only round up the divisor iff divisor is > 3.
Rounding up lower divisors makes the error too big, causing USB
on MPC832x to fail.

Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 01:28:42 -06:00
Kumar Gala 05011f370a powerpc/85xx: Fix compile error on p3060_qds.c
arch/powerpc/platforms/85xx/p3060_qds.c: In function '__machine_initcall_p3060_qds_declare_of_platform_devices':
arch/powerpc/platforms/85xx/p3060_qds.c:73:1: error: implicit declaration of function 'declare_of_platform_devices'

declare_of_platform_devices should have been corenet_ds_publish_devices.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-23 22:55:47 -06:00
Paul Bolle a92282524a powerpc/p3060qds: Fix select of 'MPC8xxx_GPIO'
The driver for the Freescale P3060 QDS got added by commit 96cc017c5b
("[...] Add support for P3060QDS board"). Its Kconfig entry selects
MPC8xxx_GPIO. But at the time that driver got added MPC8xxx_GPIO was
already renamed to GPIO_MPC8XXX, by commit c68308dd50 ("gpio: move
mpc8xxx/512x gpio driver to drivers/gpio").

So make this driver select GPIO_MPC8XXX.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-23 22:55:47 -06:00
Roy Zang c3c3ced77f powerpc/p1023: set IRQ[4:6,11] to active-high level sensitive for PCIe
P1023 external IRQ[4:6, 11] are not pin out, but the interrupts are
utilized by the PCIe controllers.  As they are not exposed as pins we
need to set them as active-high (internal to the SoC these interrupts
are pulled down).

IRQs[0:3,7:10] are pulled up on the board so we have them set as
active-low.

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-23 22:55:47 -06:00
Tejun Heo d88e4cb671 freezer: remove now unused TIF_FREEZE
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-arch@vger.kernel.org
2011-11-21 12:32:25 -08:00
David S. Miller efd0bf97de Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
The forcedeth changes had a conflict with the conversion over
to atomic u64 statistics in net-next.

The libertas cfg.c code had a conflict with the bss reference
counting fix by John Linville in net-next.

Conflicts:
	drivers/net/ethernet/nvidia/forcedeth.c
	drivers/net/wireless/libertas/cfg.c
2011-11-21 13:50:33 -05:00
Linus Torvalds a4cc3889f7 Merge branch 'kvm-updates/3.2' of git://git.kernel.org/pub/scm/virt/kvm/kvm
* 'kvm-updates/3.2' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM guest: prevent tracing recursion with kvmclock
  Revert "KVM: PPC: Add support for explicit HIOR setting"
  KVM: VMX: Check for automatic switch msr table overflow
  KVM: VMX: Add support for guest/host-only profiling
  KVM: VMX: add support for switching of PERF_GLOBAL_CTRL
  KVM: s390: announce SYNC_MMU
  KVM: s390: Fix tprot locking
  KVM: s390: handle SIGP sense running intercepts
  KVM: s390: Fix RUNNING flag misinterpretation
2011-11-20 14:57:43 -08:00
John W. Linville e11c259f74 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
Conflicts:
	include/net/bluetooth/bluetooth.h
2011-11-17 13:11:43 -05:00
Alexander Graf bb75c627fb Revert "KVM: PPC: Add support for explicit HIOR setting"
This reverts commit a15bd354f0.

It exceeded the padding on the SREGS struct, rendering the ABI
backwards-incompatible.

Conflicts:

	arch/powerpc/kvm/powerpc.c
	include/linux/kvm.h

Signed-off-by: Avi Kivity <avi@redhat.com>
2011-11-17 16:30:25 +02:00
Will Deacon a313f4c55d powerpc/signal32: Fix sigset_t conversion when copying to user
On PPC64, put_sigset_t converts a sigset_t to a compat_sigset_t
before copying it to userspace. There is a typo in the case that
we have 4 words to copy, meaning that we corrupt the compat_sigset_t.

It appears that _NSIG_WORDS can't be greater than 2 at the moment
so this code is probably always optimised away anyway.

Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-17 16:41:10 +11:00
Benjamin Herrenschmidt b97021f855 powerpc: Fix atomic_xxx_return barrier semantics
The Documentation/memory-barriers.txt document requires that atomic
operations that return a value act as a memory barrier both before
and after the actual atomic operation.

Our current implementation doesn't guarantee this. More specifically,
while a load following the isync can not be issued before stwcx. has
completed, that completion doesn't architecturally means that the
result of stwcx. is visible to other processors (or any previous stores
for that matter) (typically, the other processors L1 caches can still
hold the old value).

This has caused an actual crash in RCU torture testing on Power 7

This fixes it by changing those atomic ops to use new macros instead
of RELEASE/ACQUIRE barriers, called ATOMIC_ENTRY and ATMOIC_EXIT barriers,
which are then defined respectively to lwsync and sync.

I haven't had a chance to measure the performance impact (or rather
what I measured with kernel compiles is in the noise, I yet have to
find a more precise benchmark)

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
2011-11-17 16:26:07 +11:00
Kyle Moffett a9a8f77ac7 powerpc: Remove buggy 9-year-old test for binutils < 2.12.1
Recent binutils refuses to assemble AltiVec opcodes when in e500/SPE
mode, as some of those opcodes alias the "SPE" instructions.  This
triggers an ancient binutils version check even when building a kernel
with CONFIG_ALTIVEC disabled.

In theory, the check could be conditionalized on CONFIG_ALTIVEC, but in
practice it has long outlived its utility.  It is virtually impossible
to find binutils older than 2.12.1 (released 2002) in the wild anymore.
Even ancient RedHat Enterprise Linux 4 has binutils-2.14.

To fix the kernel build when done natively on e500 systems with this new
binutils, the test is simply removed.

Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-17 16:26:07 +11:00
Kumar Gala 187b9f2aa7 powerpc/book3e-64: Fix debug support for userspace
With the introduction of CONFIG_PPC_ADV_DEBUG_REGS user space debug is
broken on Book-E 64-bit parts that support delayed debug events.  When
switch_booke_debug_regs() sets DBCR0 we'll start getting debug events as
MSR_DE is also set and we aren't able to handle debug events from kernel
space.

We can remove the hack that always enables MSR_DE and loads up DBCR0 and
just utilize switch_booke_debug_regs() to get user space debug working
again.

We still need to handle critical/debug exception stacks & proper
save/restore of state for those exception levles to support debug events
from kernel space like we have on 32-bit.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-17 16:26:07 +11:00
Kumar Gala b95bc21914 powerpc: Remove extraneous CONFIG_PPC_ADV_DEBUG_REGS define
All of DebugException is already protected by CONFIG_PPC_ADV_DEBUG_REGS
there is no need to have another such ifdef inside the function.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-17 16:26:07 +11:00
Kumar Gala ba28c9aae2 powerpc: Revert show_regs() define for readability
We had an existing ifdef for 4xx & BOOKE processors that got changed to
CONFIG_PPC_ADV_DEBUG_REGS.  The define has nothing to do with
CONFIG_PPC_ADV_DEBUG_REGS.  The define really should be:

 #if defined(CONFIG_4xx) || defined(CONFIG_BOOKE)

and not

 #ifdef CONFIG_PPC_ADV_DEBUG_REGS

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-17 16:26:07 +11:00
Geoff Levand 7eaf09eefe powerpc/ps3: Fix SMP lockdep boot warning
Move the PS3 IPI message setup from ps3_smp_setup_cpu() to ps3_smp_probe().

Fixes startup warnings like these:

  ------------[ cut here ]------------
  WARNING: at kernel/lockdep.c:2649
  Modules linked in:
  ...
  ---[ end trace 31fd0ba7d8756001 ]---

Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-16 14:47:54 +11:00
Geoff Levand 72f3bea075 powerpc/ps3: Fix lost SMP IPIs
Fixes the PS3 bootup hang introduced in 3.0-rc1 by:

  commit 317f394160
  sched: Move the second half of ttwu() to the remote cpu

Move the PS3's LV1 EOI call lv1_end_of_interrupt_ext() from ps3_chip_eoi()
to ps3_get_irq() for IPI messages.

If lv1_send_event_locally() is called between a previous call to
lv1_send_event_locally() and the coresponding call to
lv1_end_of_interrupt_ext() the second event will not be delivered to the
target cpu.

The PS3's SMP IPIs are implemented using lv1_send_event_locally(), so if two
IPI messages of the same type are sent to the same target in a relatively
short period of time the second IPI event can become lost when
lv1_end_of_interrupt_ext() is called from ps3_chip_eoi().

CC: stable@kernel.org
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-16 14:47:54 +11:00
Michael Neuling de1d9248ea powerpc: Add hvcall.h include to book3s_hv.c
If you build with KVM and UP it fails with the following due to a
missing include.

/arch/powerpc/kvm/book3s_hv.c: In function 'do_h_register_vpa':
arch/powerpc/kvm/book3s_hv.c:156:10: error: 'H_PARAMETER' undeclared (first use in this function)
arch/powerpc/kvm/book3s_hv.c:156:10: note: each undeclared identifier is reported only once for each function it appears in
arch/powerpc/kvm/book3s_hv.c:192:12: error: 'H_RESOURCE' undeclared (first use in this function)
arch/powerpc/kvm/book3s_hv.c:222:9: error: 'H_SUCCESS' undeclared (first use in this function)
arch/powerpc/kvm/book3s_hv.c: In function 'kvmppc_pseries_do_hcall':
arch/powerpc/kvm/book3s_hv.c:228:30: error: 'H_SUCCESS' undeclared (first use in this function)
arch/powerpc/kvm/book3s_hv.c:232:7: error: 'H_CEDE' undeclared (first use in this function)
arch/powerpc/kvm/book3s_hv.c:234:7: error: 'H_PROD' undeclared (first use in this function)
arch/powerpc/kvm/book3s_hv.c:238:10: error: 'H_PARAMETER' undeclared (first use in this function)
arch/powerpc/kvm/book3s_hv.c:250:7: error: 'H_CONFER' undeclared (first use in this function)
arch/powerpc/kvm/book3s_hv.c:252:7: error: 'H_REGISTER_VPA' undeclared (first use in this function)
make[2]: *** [arch/powerpc/kvm/book3s_hv.o] Error 1

Signed-off-by: Michael Neuling <mikey@neuling.org>
cc: stable@kernel.org (3.1 only)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-16 14:47:54 +11:00
Kevin Hao 2cd76629f6 powerpc/trace: Add a dummy stack frame for trace_hardirqs_off
The trace_hardirqs_off will use CALLER_ADDR0 and CALLER_ADDR1.
If an exception occurs in user mode, there is only one stack frame
on the stack and accessing the CALLER_ADDR1 will causes the following
call trace. So we create a dummy stack frame to make
trace_hardirqs_off happy.

WARNING: at kernel/smp.c:459
Modules linked in:
NIP: c0093280 LR: c00930a0 CTR: c0010780
REGS: edb87ae0 TRAP: 0700   Not tainted  (3.1.0)
MSR: 00021002 <ME,CE>  CR: 28002888  XER: 00000000
TASK = edce2ac0[17658] 'mthread-lock-on' THREAD: edb86000 CPU: 5
GPR00: 00000001 edb87b90 edce2ac0 00000005 c0019594 edb87bd8 00000001 00000fe3
GPR08: 00041000 c084138c 4e20120d edb87b90 48002888 1001aa7c 00000000 00000000
GPR16: 48830000 10012a8c 00000000 10000af4 00000001 c0810000 00000000 00000000
GPR24: ee9aa920 c0816a18 00000000 00000005 c0019594 edb87bd8 ee20178c edb87b90
NIP [c0093280] smp_call_function_many+0x214/0x2b4
LR [c00930a0] smp_call_function_many+0x34/0x2b4
Call Trace:
[edb87b90] [c00930a0] smp_call_function_many+0x34/0x2b4 (unreliable)
[edb87bd0] [c00194ec] __flush_tlb_page+0xac/0x100
[edb87c00] [c001957c] flush_tlb_page+0x3c/0x54
[edb87c10] [c00180ac] ptep_set_access_flags+0x74/0x12c
[edb87c40] [c0128068] handle_pte_fault+0x2f0/0x9ac
[edb87cb0] [c0128c3c] handle_mm_fault+0x104/0x1dc
[edb87ce0] [c05f40f4] do_page_fault+0x2dc/0x630
[edb87e50] [c001078c] handle_page_fault+0xc/0x80

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-16 14:47:54 +11:00
Anton Blanchard d715e433b7 powerpc: Copy down exception vectors after feature fixups
kdump fails because we try to execute an HV only instruction. Feature
fixups are being applied after we copy the exception vectors down to 0
so they miss out on any updates.

We have always had this issue but it only became critical in v3.0
when we added CFAR support (breaks POWER5) and v3.1 when we added
POWERNV (breaks everyone).

Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org> [v3.0+]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-16 14:47:54 +11:00
Anton Blanchard 6d1e2c6c1a powerpc: panic if we can't instantiate RTAS
I had to debug a strange situation where all manner of things were
failing. SMT threads, storage and network were all completely broken.

The root cause was we couldn't find enough memory to instantiate RTAS -
this was a network install so the initrd was huge.

Instead of limping along and failing in mysterious ways we should just
panic up front if RTAS exists and we can't allocate space for it.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-16 14:47:54 +11:00
Suzuki Poulose bbc24a25e2 powerpc/4xx: Fix typos in kexec config dependencies
Kexec is not supported on 47x. 47x is a variant of 44x with slightly
different MMU and SMP support. There was a typo in the config dependency
for kexec. This patch fixes the same.

Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Cc:	Kumar Gala <galak@kernel.crashing.org>
Cc:	Josh Boyer <jwboyer@gmail.com>
Cc:	linux ppc dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-16 14:47:54 +11:00
Al Viro 82640a6b91 powerpc/fsl: MCU_MPC8349EMITX wants I2C built-in, modular won't do...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-16 14:25:19 +11:00
Al Viro 9c8b39077b powerpc: Fix build breakage in jump_label.c
Should do what other architectures do and wrap all that code into
the appropriate ifdef

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-16 14:25:19 +11:00
Linus Torvalds 642ba5ed7a Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
  fsl-rio: fix compile error
2011-11-15 14:47:28 -02:00
Liu Gang e0ce42e19c fsl-rio: fix compile error
The "#include <linux/module.h>" was replaced by "#include <linux/export.h>"
in the patch "powerpc: various straight conversions from module.h --> export.h".
This will cause the following compile problem:
arch/powerpc/sysdev/fsl_rio.c: In function 'fsl_rio_mcheck_exception':
arch/powerpc/sysdev/fsl_rio.c:296: error: implicit declaration of function 'search_exception_tables'.

The file fsl_rio.c needs the declaration of function "search_exception_tables"
in the header file "linux/module.h".

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-11-14 12:43:17 -05:00
Paul Bolle 085c9461ed powerpc/mpc5121: drop "select MPC5121_ADS_CPLD"
There is no Kconfig symbol named MPC5121_ADS_CPLD. The select statement
for that symbol is a nop. Drop it.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-11-13 20:57:45 +01:00
Jiri Kosina 2290c0d06d Merge branch 'master' into for-next
Sync with Linus tree to have 157550ff ("mtd: add GPMI-NAND driver
in the config and Makefile") as I have patch depending on that one.
2011-11-13 20:55:53 +01:00
Paul Bolle b4da228c64 powerpc/4xx: Fix typo 'PCC4xx_MSI'
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Josh Boyer <jwboyer@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-11-13 20:47:07 +01:00
Johannes Berg 6e3e939f3b net: add wireless TX status socket option
The 802.1X EAPOL handshake hostapd does requires
knowing whether the frame was ack'ed by the peer.
Currently, we fudge this pretty badly by not even
transmitting the frame as a normal data frame but
injecting it with radiotap and getting the status
out of radiotap monitor as well. This is rather
complex, confuses users (mon.wlan0 presence) and
doesn't work with all hardware.

To get rid of that hack, introduce a real wifi TX
status option for data frame transmissions.

This works similar to the existing TX timestamping
in that it reflects the SKB back to the socket's
error queue with a SCM_WIFI_STATUS cmsg that has
an int indicating ACK status (0/1).

Since it is possible that at some point we will
want to have TX timestamping and wifi status in a
single errqueue SKB (there's little point in not
doing that), redefine SO_EE_ORIGIN_TIMESTAMPING
to SO_EE_ORIGIN_TXSTATUS which can collect more
than just the timestamp; keep the old constant
as an alias of course. Currently the internal APIs
don't make that possible, but it wouldn't be hard
to split them up in a way that makes it possible.

Thanks to Neil Horman for helping me figure out
the functions that add the control messages.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-09 16:01:02 -05:00
Alexander Graf 5ccf55dd81 powerpc/kvm: Fix build failure with HV KVM and CBE
When running with HV KVM and CBE config options enabled, I get
build failures like the following:

  arch/powerpc/kernel/head_64.o: In function `cbe_system_error_hv':
  (.text+0x1228): undefined reference to `do_kvm_0x1202'
  arch/powerpc/kernel/head_64.o: In function `cbe_maintenance_hv':
  (.text+0x1628): undefined reference to `do_kvm_0x1602'
  arch/powerpc/kernel/head_64.o: In function `cbe_thermal_hv':
  (.text+0x1828): undefined reference to `do_kvm_0x1802'

This is because we jump to a KVM handler when HV is enabled, but we
only generate the handler with PR KVM mode.

Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-08 15:34:04 +11:00
Benjamin Herrenschmidt f81f5e14de Merge remote-tracking branch 'agust/next' into merge 2011-11-08 14:53:55 +11:00
Geoff Levand 9fce85f7ff powerpc/ps3: Fix lv1_gpu_attribute hcall
The lv1_gpu_attribute hcall takes three, not five input
arguments.  Adjust the lv1 hcall table and all calls.

Signed-off-by: Geoff Levand <geoff@infradead.org>
CC: Takashi Iwai <tiwai@suse.de>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-08 14:51:59 +11:00
Geoff Levand 5233e26ebb powerpc/ps3: Fix PS3 repository build warnings
Fix uninitialized variable warnings in build of repository.c

Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-08 14:51:58 +11:00
Yong Zhang a3a9f3b47d powerpc/irq: Remove IRQF_DISABLED
Since commit [e58aa3d2: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled
and we even check and yell when an interrupt handler
returns with interrupts enabled (see commit [b738a50a:
genirq: Warn when handler enables interrupts]).

So now this flag is a NOOP and can be removed.

Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-08 14:51:46 +11:00
Dipankar Sarma 1c8ee73395 powerpc/numa: NUMA topology support for PowerNV
This patch adds support for numa topology on powernv platforms running
OPAL formware. It checks for the type of platform at run time and
sets the affinity form correctly so that NUMA topology can be discovered
correctly.

Signed-off-by: Dipankar Sarma <dipankar@in.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-08 14:51:46 +11:00
Anton Blanchard c40dd2f766 powerpc: Add System RAM to /proc/iomem
We've resisted adding System RAM to /proc/iomem because it is
the wrong place for it. Unfortunately we continue to find tools
that rely on this behaviour so give up and add it in.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-08 14:51:46 +11:00
Michael Neuling 88cf11b4cc powerpc: Add KVM as module to defconfigs
Add HV mode KVM to Book3 server 64bit defconfigs as a module.

Doesn't add much to the size:
   text	   data	    bss	     dec	    hex	filename
8244109	4686767	 994000	13924876	 d47a0c	vmlinux.vanilla
8256092 4691607  994128 13941827         d4bc43 vmlinux.kvm

This should enable more testing of this configuration.

Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-08 14:51:03 +11:00
Nishanth Aravamudan ad61d64e26 powerpc/kvm: Fix build with older toolchains
Fix KVM build for older toolchains (found with .powerpc64-unknown-linux-gnu-gcc
(crosstool-NG-1.8.1) 4.3.2):

  AS      arch/powerpc/kvm/book3s_hv_rmhandlers.o
arch/powerpc/kvm/book3s_hv_rmhandlers.S: Assembler messages:
arch/powerpc/kvm/book3s_hv_rmhandlers.S:1388: Error: Unrecognized opcode: `popcntw'
make[1]: *** [arch/powerpc/kvm/book3s_hv_rmhandlers.o] Error 1
make: *** [_module_arch/powerpc/kvm] Error 2

Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-11-08 14:51:03 +11:00
Linus Torvalds 32aaeffbd4 Merge branch 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
  Revert "tracing: Include module.h in define_trace.h"
  irq: don't put module.h into irq.h for tracking irqgen modules.
  bluetooth: macroize two small inlines to avoid module.h
  ip_vs.h: fix implicit use of module_get/module_put from module.h
  nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
  include: replace linux/module.h with "struct module" wherever possible
  include: convert various register fcns to macros to avoid include chaining
  crypto.h: remove unused crypto_tfm_alg_modname() inline
  uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
  pm_runtime.h: explicitly requires notifier.h
  linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
  miscdevice.h: fix up implicit use of lists and types
  stop_machine.h: fix implicit use of smp.h for smp_processor_id
  of: fix implicit use of errno.h in include/linux/of.h
  of_platform.h: delete needless include <linux/module.h>
  acpi: remove module.h include from platform/aclinux.h
  miscdevice.h: delete unnecessary inclusion of module.h
  device_cgroup.h: delete needless include <linux/module.h>
  net: sch_generic remove redundant use of <linux/module.h>
  net: inet_timewait_sock doesnt need <linux/module.h>
  ...

Fix up trivial conflicts (other header files, and  removal of the ab3550 mfd driver) in
 - drivers/media/dvb/frontends/dibx000_common.c
 - drivers/media/video/{mt9m111.c,ov6650.c}
 - drivers/mfd/ab3550-core.c
 - include/linux/dmaengine.h
2011-11-06 19:44:47 -08:00
Linus Torvalds 02ebbbd481 Merge branch 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  scsi: drop unused Kconfig symbol
  pci: drop unused Kconfig symbol
  stmmac: drop unused Kconfig symbol
  x86: drop unused Kconfig symbol
  powerpc: drop unused Kconfig symbols
  powerpc: 40x: drop unused Kconfig symbol
  mips: drop unused Kconfig symbols
  openrisc: drop unused Kconfig symbols
  arm: at91: drop unused Kconfig symbol
  samples: drop unused Kconfig symbol
  m32r: drop unused Kconfig symbol
  score: drop unused Kconfig symbols
  sh: drop unused Kconfig symbol
  um: drop unused Kconfig symbol
  sparc: drop unused Kconfig symbol
  alpha: drop unused Kconfig symbol

Fix up trivial conflict in drivers/net/ethernet/stmicro/stmmac/Kconfig
as per Michal: the STMMAC_DUAL_MAC config variable is still unused and
should be deleted.
2011-11-06 18:54:53 -08:00
Linus Torvalds 1197ab2942 Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (106 commits)
  powerpc/p3060qds: Add support for P3060QDS board
  powerpc/83xx: Add shutdown request support to MCU handling on MPC8349 MITX
  powerpc/85xx: Make kexec to interate over online cpus
  powerpc/fsl_booke: Fix comment in head_fsl_booke.S
  powerpc/85xx: issue 15 EOI after core reset for FSL CoreNet devices
  powerpc/8xxx: Fix interrupt handling in MPC8xxx GPIO driver
  powerpc/85xx: Add 'fsl,pq3-gpio' compatiable for GPIO driver
  powerpc/86xx: Correct Gianfar support for GE boards
  powerpc/cpm: Clear muram before it is in use.
  drivers/virt: add ioctl for 32-bit compat on 64-bit to fsl-hv-manager
  powerpc/fsl_msi: add support for "msi-address-64" property
  powerpc/85xx: Setup secondary cores PIR with hard SMP id
  powerpc/fsl-booke: Fix settlbcam for 64-bit
  powerpc/85xx: Adding DCSR node to dtsi device trees
  powerpc/85xx: clean up FPGA device tree nodes for Freecsale QorIQ boards
  powerpc/85xx: fix PHYS_64BIT selection for P1022DS
  powerpc/fsl-booke: Fix setup_initial_memory_limit to not blindly map
  powerpc: respect mem= setting for early memory limit setup
  powerpc: Update corenet64_smp_defconfig
  powerpc: Update mpc85xx/corenet 32-bit defconfigs
  ...

Fix up trivial conflicts in:
 - arch/powerpc/configs/40x/hcu4_defconfig
	removed stale file, edited elsewhere
 - arch/powerpc/include/asm/udbg.h, arch/powerpc/kernel/udbg.c:
	added opal and gelic drivers vs added ePAPR driver
 - drivers/tty/serial/8250.c
	moved UPIO_TSI to powerpc vs removed UPIO_DWAPB support
2011-11-06 17:12:03 -08:00
Linus Torvalds b4fdcb02f1 Merge branch 'for-3.2/core' of git://git.kernel.dk/linux-block
* 'for-3.2/core' of git://git.kernel.dk/linux-block: (29 commits)
  block: don't call blk_drain_queue() if elevator is not up
  blk-throttle: use queue_is_locked() instead of lockdep_is_held()
  blk-throttle: Take blkcg->lock while traversing blkcg->policy_list
  blk-throttle: Free up policy node associated with deleted rule
  block: warn if tag is greater than real_max_depth.
  block: make gendisk hold a reference to its queue
  blk-flush: move the queue kick into
  blk-flush: fix invalid BUG_ON in blk_insert_flush
  block: Remove the control of complete cpu from bio.
  block: fix a typo in the blk-cgroup.h file
  block: initialize the bounce pool if high memory may be added later
  block: fix request_queue lifetime handling by making blk_queue_cleanup() properly shutdown
  block: drop @tsk from attempt_plug_merge() and explain sync rules
  block: make get_request[_wait]() fail if queue is dead
  block: reorganize throtl_get_tg() and blk_throtl_bio()
  block: reorganize queue draining
  block: drop unnecessary blk_get/put_queue() in scsi_cmd_ioctl() and blk_get_tg()
  block: pass around REQ_* flags instead of broken down booleans during request alloc/free
  block: move blk_throtl prototypes to block/blk.h
  block: fix genhd refcounting in blkio_policy_parse_and_set()
  ...

Fix up trivial conflicts due to "mddev_t" -> "struct mddev" conversion
and making the request functions be of type "void" instead of "int" in
 - drivers/md/{faulty.c,linear.c,md.c,md.h,multipath.c,raid0.c,raid1.c,raid10.c,raid5.c}
 - drivers/staging/zram/zram_drv.c
2011-11-04 17:06:58 -07:00
Shengzhou Liu 96cc017c5b powerpc/p3060qds: Add support for P3060QDS board
The P3060QDS is a Freescale reference board that hosts the six-core P3060 SOC.
The P3060 Processor combines six e500mc Power Architecture processor cores with
high-performance datapath acceleration architecture(DPAA), CoreNet fabric
infrastructure, as well as network and peripheral interfaces.

P3060QDS Board Overview:
Memory subsystem:
  - 2G Bytes unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
  - 128M Bytes NOR flash single-chip memory
  - 16M Bytes SPI flash
  - 8K Bytes AT24C64 I2C EEPROM
Ethernet:
  - 4x1G + 4x1G/2.5G Ethernet controllers
  - 2xRGMII + 1xMII, three VSC8641 PHYs on board
  - Suport multiple Vitesse VSC8234 SGMII Cards in Slot1/2/3
PCIe: Two PCI Express 2.0 controllers/ports
USB:  Two USB2.0, USB1(TYPE-A) and USB2(TYPE-AB) on board
I2C:  Four I2C controllers
UART: Supports up to four UARTs
RapidIO: Supports two serial RapidIO ports

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-03 13:20:47 -05:00
Fabio Baltieri 6ca6ca5d81 powerpc/83xx: Add shutdown request support to MCU handling on MPC8349 MITX
This patch add support for calling ctrl_alt_del() when the power button is
pressed for more than about 2 seconds on some freescale MPC83xx evaluation
boards and reference design.

The code uses a kthread to poll the CTRL_BTN bit each second.

Also change Kconfig entry of the driver to bool, as device's gpio
registration is broken when loading as module.

Tested on an MPC8315E RDB board.

Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-03 13:12:30 -05:00
Matthew McClintock 43a327b79c powerpc/85xx: Make kexec to interate over online cpus
This is not strictly required, because this iterates over logical
cpus and they are not (currently) discontigous. But, it's cleaner
code and more obvious what is going on

Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-03 13:12:29 -05:00
Matthew McClintock 7d0d3ad5e3 powerpc/fsl_booke: Fix comment in head_fsl_booke.S
Fix typo in comments introduced by:

commit 6dece0eb69
Author: Scott Wood <scottwood@freescale.com>
Date:   Mon Jul 25 11:29:33 2011 +0000

    powerpc/32: Pass device tree address as u64 to machine_init

Signed-off-by: Matthew McClintock <msm@freescale.com>
cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-03 13:12:28 -05:00
Matthew McClintock 44f16fcf2f powerpc/85xx: issue 15 EOI after core reset for FSL CoreNet devices
This is listed as a requirement for Freescale CoreNet based devices  (e.g
p4080ds with MPIC v4.x) after issuing a core reset to properly clear pending
interrupts.

Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-03 13:12:27 -05:00
Martyn Welch 62f3de91e4 powerpc/86xx: Correct Gianfar support for GE boards
The GE DTBs were not updated when the Gianfar driver was converted to an
of_platform_driver in commit b31a1d8b41. Update
the DTBs, adding the required TBI entries.

Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-03 12:57:20 -05:00
Liu Gang e80dd9a7bc arch/powerpc/sysdev/fsl_rio.c: release rapidio port I/O region resource if port failed to initialize
The "struct rio_mport" contains a member of master port I/O memory
resource structure "struct resource iores".  This resource will be read
from device tree and be used for rapidio R/W transaction memory space.
Rapidio requests the port I/O memory resource under the root resource
"iomem_resource".

			struct rio_mport *port;
			port = kzalloc(sizeof(struct rio_mport), GFP_KERNEL);

			request_resource(&iomem_resource, &port->iores);

When port failed to initialize, allocated "rio_mport" structure memory
will be freed, and the port I/O memory resource structure pointer
"&port->iores" will be invalid.  If other requests resource under
"iomem_resource", "&port->iores" node may be operated in the child
resources list and this will cause the system to crash.

So the requested port I/O memory resource should be released before
freeing allocated "rio_mport" structure.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Acked-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-11-02 16:07:01 -07:00
Andrea Arcangeli b35a35b556 thp: share get_huge_page_tail()
This avoids duplicating the function in every arch gup_fast.

Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Hugh Dickins <hughd@google.com>
Cc: Johannes Weiner <jweiner@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-11-02 16:06:58 -07:00
Andrea Arcangeli cf592bf768 powerpc: gup_huge_pmd() return 0 if pte changes
powerpc didn't return 0 in that case, if it's rolling back the *nr pointer
it should also return zero to avoid adding pages to the array at the wrong
offset.

Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Hugh Dickins <hughd@google.com>
Cc: Johannes Weiner <jweiner@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-11-02 16:06:57 -07:00
Andrea Arcangeli 3526741f09 powerpc: gup_hugepte() support THP based tail recounting
Up to this point the code assumed old refcounting for hugepages (pre-thp).
This updates the code directly to the thp mapcount tail page refcounting.

Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Hugh Dickins <hughd@google.com>
Cc: Johannes Weiner <jweiner@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-11-02 16:06:57 -07:00
Andrea Arcangeli 8596468487 powerpc: gup_hugepte() avoid freeing the head page too many times
We only taken "refs" pins on the head page not "*nr" pins.

Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Hugh Dickins <hughd@google.com>
Cc: Johannes Weiner <jweiner@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-11-02 16:06:57 -07:00
Andrea Arcangeli 405e44f2e3 powerpc: get_hugepte() don't put_page() the wrong page
"page" may have changed to point to the next hugepage after the loop
completed, The references have been taken on the head page, so the
put_page must happen there too.

This is a longstanding issue pre-thp inclusion.

It's totally unclear how these page_cache_add_speculative and
pte_val(pte) != pte_val(*ptep) checks are necessary across all the
powerpc gup_fast code, when x86 doesn't need any of that: there's no way
the page can be freed with irq disabled so we're guaranteed the
atomic_inc will happen on a page with page_count > 0 (so not needing the
speculative check).

The pte check is also meaningless on x86: no need to rollback on x86 if
the pte changed, because the pte can still change a CPU tick after the
check succeeded and it won't be rolled back in that case.  The important
thing is we got a reference on a valid page that was mapped there a CPU
tick ago.  So not knowing the soft tlb refill code of ppc64 in great
detail I'm not removing the "speculative" page_count increase and the
pte checks across all the code, but unless there's a strong reason for
it they should be later cleaned up too.

If a pte can change from huge to non-huge (like it could happen with
THP) passing a pte_t *ptep to gup_hugepte() would also require to repeat
the is_hugepd in gup_hugepte(), but that shouldn't happen with hugetlbfs
only so I'm not altering that.

Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Hugh Dickins <hughd@google.com>
Cc: Johannes Weiner <jweiner@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-11-02 16:06:57 -07:00
Andrea Arcangeli 2839bdc1bf powerpc: remove superfluous PageTail checks on the pte gup_fast
This part of gup_fast doesn't seem capable of handling hugetlbfs ptes,
those should be handled by gup_hugepd only, so these checks are
superfluous.

Plus if this wasn't a noop, it would have oopsed because, the insistence
of using the speculative refcounting would trigger a VM_BUG_ON if a tail
page was encountered in the page_cache_get_speculative().

Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Hugh Dickins <hughd@google.com>
Cc: Johannes Weiner <jweiner@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-11-02 16:06:57 -07:00
Andrea Arcangeli 70b50f94f1 mm: thp: tail page refcounting fix
Michel while working on the working set estimation code, noticed that
calling get_page_unless_zero() on a random pfn_to_page(random_pfn)
wasn't safe, if the pfn ended up being a tail page of a transparent
hugepage under splitting by __split_huge_page_refcount().

He then found the problem could also theoretically materialize with
page_cache_get_speculative() during the speculative radix tree lookups
that uses get_page_unless_zero() in SMP if the radix tree page is freed
and reallocated and get_user_pages is called on it before
page_cache_get_speculative has a chance to call get_page_unless_zero().

So the best way to fix the problem is to keep page_tail->_count zero at
all times.  This will guarantee that get_page_unless_zero() can never
succeed on any tail page.  page_tail->_mapcount is guaranteed zero and
is unused for all tail pages of a compound page, so we can simply
account the tail page references there and transfer them to
tail_page->_count in __split_huge_page_refcount() (in addition to the
head_page->_mapcount).

While debugging this s/_count/_mapcount/ change I also noticed get_page is
called by direct-io.c on pages returned by get_user_pages.  That wasn't
entirely safe because the two atomic_inc in get_page weren't atomic.  As
opposed to other get_user_page users like secondary-MMU page fault to
establish the shadow pagetables would never call any superflous get_page
after get_user_page returns.  It's safer to make get_page universally safe
for tail pages and to use get_page_foll() within follow_page (inside
get_user_pages()).  get_page_foll() is safe to do the refcounting for tail
pages without taking any locks because it is run within PT lock protected
critical sections (PT lock for pte and page_table_lock for
pmd_trans_huge).

The standard get_page() as invoked by direct-io instead will now take
the compound_lock but still only for tail pages.  The direct-io paths
are usually I/O bound and the compound_lock is per THP so very
finegrined, so there's no risk of scalability issues with it.  A simple
direct-io benchmarks with all lockdep prove locking and spinlock
debugging infrastructure enabled shows identical performance and no
overhead.  So it's worth it.  Ideally direct-io should stop calling
get_page() on pages returned by get_user_pages().  The spinlock in
get_page() is already optimized away for no-THP builds but doing
get_page() on tail pages returned by GUP is generally a rare operation
and usually only run in I/O paths.

This new refcounting on page_tail->_mapcount in addition to avoiding new
RCU critical sections will also allow the working set estimation code to
work without any further complexity associated to the tail page
refcounting with THP.

Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reported-by: Michel Lespinasse <walken@google.com>
Reviewed-by: Michel Lespinasse <walken@google.com>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Hugh Dickins <hughd@google.com>
Cc: Johannes Weiner <jweiner@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: <stable@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-11-02 16:06:57 -07:00
Christopher Yeoh fcf634098c Cross Memory Attach
The basic idea behind cross memory attach is to allow MPI programs doing
intra-node communication to do a single copy of the message rather than a
double copy of the message via shared memory.

The following patch attempts to achieve this by allowing a destination
process, given an address and size from a source process, to copy memory
directly from the source process into its own address space via a system
call.  There is also a symmetrical ability to copy from the current
process's address space into a destination process's address space.

- Use of /proc/pid/mem has been considered, but there are issues with
  using it:
  - Does not allow for specifying iovecs for both src and dest, assuming
    preadv or pwritev was implemented either the area read from or
  written to would need to be contiguous.
  - Currently mem_read allows only processes who are currently
  ptrace'ing the target and are still able to ptrace the target to read
  from the target. This check could possibly be moved to the open call,
  but its not clear exactly what race this restriction is stopping
  (reason  appears to have been lost)
  - Having to send the fd of /proc/self/mem via SCM_RIGHTS on unix
  domain socket is a bit ugly from a userspace point of view,
  especially when you may have hundreds if not (eventually) thousands
  of processes  that all need to do this with each other
  - Doesn't allow for some future use of the interface we would like to
  consider adding in the future (see below)
  - Interestingly reading from /proc/pid/mem currently actually
  involves two copies! (But this could be fixed pretty easily)

As mentioned previously use of vmsplice instead was considered, but has
problems.  Since you need the reader and writer working co-operatively if
the pipe is not drained then you block.  Which requires some wrapping to
do non blocking on the send side or polling on the receive.  In all to all
communication it requires ordering otherwise you can deadlock.  And in the
example of many MPI tasks writing to one MPI task vmsplice serialises the
copying.

There are some cases of MPI collectives where even a single copy interface
does not get us the performance gain we could.  For example in an
MPI_Reduce rather than copy the data from the source we would like to
instead use it directly in a mathops (say the reduce is doing a sum) as
this would save us doing a copy.  We don't need to keep a copy of the data
from the source.  I haven't implemented this, but I think this interface
could in the future do all this through the use of the flags - eg could
specify the math operation and type and the kernel rather than just
copying the data would apply the specified operation between the source
and destination and store it in the destination.

Although we don't have a "second user" of the interface (though I've had
some nibbles from people who may be interested in using it for intra
process messaging which is not MPI).  This interface is something which
hardware vendors are already doing for their custom drivers to implement
fast local communication.  And so in addition to this being useful for
OpenMPI it would mean the driver maintainers don't have to fix things up
when the mm changes.

There was some discussion about how much faster a true zero copy would
go. Here's a link back to the email with some testing I did on that:

http://marc.info/?l=linux-mm&m=130105930902915&w=2

There is a basic man page for the proposed interface here:

http://ozlabs.org/~cyeoh/cma/process_vm_readv.txt

This has been implemented for x86 and powerpc, other architecture should
mainly (I think) just need to add syscall numbers for the process_vm_readv
and process_vm_writev. There are 32 bit compatibility versions for
64-bit kernels.

For arch maintainers there are some simple tests to be able to quickly
verify that the syscalls are working correctly here:

http://ozlabs.org/~cyeoh/cma/cma-test-20110718.tgz

Signed-off-by: Chris Yeoh <yeohc@au1.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Howells <dhowells@redhat.com>
Cc: James Morris <jmorris@namei.org>
Cc: <linux-man@vger.kernel.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-10-31 17:30:44 -07:00
Paul Gortmaker ead53f22dc powerpc: remove non-required uses of include <linux/module.h>
None of the files touched here are modules, and they are not
exporting any symbols either -- so there is no need to be including
the module.h.  Builds of all the files remains successful.

Even kernel/module.c does not need to include it, since it includes
linux/moduleloader.h instead.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31 19:30:44 -04:00
Paul Gortmaker 4b16f8e2d6 powerpc: various straight conversions from module.h --> export.h
All these files were including module.h just for the basic
EXPORT_SYMBOL infrastructure.  We can shift them off to the
export.h header which is a way smaller footprint and thus
realize some compile time gains.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31 19:30:44 -04:00
Paul Gortmaker e9848d62ab powerpc: convert hvconsole.c to export.h ; fix implicit use of errno.h
This file is only exporting symbols and so should use export.h
and not module.h header.  But in doing the conversion, we will
uncover that it was implicitly using errno.h via module.h:

  CC      arch/powerpc/platforms/pseries/hvconsole.o
arch/powerpc/platforms/pseries/hvconsole.c: In function 'hvc_put_chars':
arch/powerpc/platforms/pseries/hvconsole.c:77: error: 'EIO' undeclared (first use in this function)

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31 19:30:43 -04:00
Paul Gortmaker 614f15b4fc powerpc: fix two implicit header uses in pseries/plpar_wrappers.h
Removing the implicit presence of module.h from almost everywhere
will reveal this implicit usage of paca.h and string.h headers as
follows:

arch/powerpc/platforms/pseries/plpar_wrappers.h:22: error: implicit declaration of function 'get_lppaca'
arch/powerpc/platforms/pseries/plpar_wrappers.h:208: error: implicit declaration of function 'memcpy'

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31 19:30:42 -04:00
Paul Gortmaker e415372acc powerpc: fix implicit use of mutex.h by include/asm/spu.h
We've been getting the header implicitly via module.h in the past
but when we clean that up, we'll get this failure:

  CC      arch/powerpc/platforms/cell/beat_spu_priv1.o
In file included from arch/powerpc/platforms/cell/beat_spu_priv1.c:22:
arch/powerpc/include/asm/spu.h:190: error: field 'list_mutex' has incomplete type
make[2]: *** [arch/powerpc/platforms/cell/beat_spu_priv1.o] Error 1

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31 19:30:42 -04:00
Paul Gortmaker cab2e05271 powerpc: fix implicit use of cache.h in kernel/firmware.c
This file only needs export.h to get EXPORT_SYMBOL, but in doing
so, it uncovers an implicit use of linux/cache.h as follows:

 CC      arch/powerpc/kernel/firmware.o
arch/powerpc/kernel/firmware.c:20: error: expected '=', ',', ';', 'asm' or '__attribute__' before '__read_mostly'
arch/powerpc/kernel/firmware.c:21: error: expected '=', ',', ';', 'asm' or '__attribute__' before '__used'
make[2]: *** [arch/powerpc/kernel/firmware.o] Error 1

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31 19:30:41 -04:00
Paul Gortmaker 2a7156b9e8 powerpc: fix implicit notifier use in converting to export.h
We can convert this file to using export.h since it only wants
to export symbols, but when we do we'll see also that it was
implicitly getting notifier.h from module.h via this failure:

  CC      arch/powerpc/platforms/cell/spu_notify.o
arch/powerpc/platforms/cell/spu_notify.c:28: warning: type defaults to 'int' in declaration of 'BLOCKING_NOTIFIER_HEAD'
arch/powerpc/platforms/cell/spu_notify.c:28: warning: parameter names (without types) in function declaration
arch/powerpc/platforms/cell/spu_notify.c: In function 'spu_switch_notify':
arch/powerpc/platforms/cell/spu_notify.c:32: error: implicit declaration of function 'blocking_notifier_call_chain'
arch/powerpc/platforms/cell/spu_notify.c:32: error: 'spu_switch_notifier' undeclared (first use in this function)

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31 19:30:41 -04:00
Paul Gortmaker 08f1e55cc7 powerpc: cell/beat_wrapper.h is implicitly using memcpy functions
This has been relying on the fact that the parent file would have
module.h (and thus nearly everything) present.  But once we fix that,
we'll get stuck with this failure:

In file included from arch/powerpc/platforms/cell/beat_spu_priv1.c:26:
arch/powerpc/platforms/cell/beat_wrapper.h: In function 'beat_eeprom_write':
arch/powerpc/platforms/cell/beat_wrapper.h:160: error: implicit declaration of function 'memcpy'

and many more instances of the same.  Fix it in advance.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31 19:30:40 -04:00
Paul Gortmaker 62fe91bba2 powerpc: Fix up implicit sched.h users
They are getting it through device.h --> module.h path, but we want
to clean that up.  This is a sample of what will happen if we don't:

  pseries/iommu.c: In function 'tce_build_pSeriesLP':
  pseries/iommu.c:136: error: implicit declaration of function 'show_stack'

  pseries/eeh.c: In function 'eeh_token_to_phys':
  pseries/eeh.c:359: error: 'init_mm' undeclared (first use in this function)

  pseries/eeh_event.c: In function 'eeh_event_handler':
  pseries/eeh_event.c:63: error: implicit declaration of function 'daemonize'
  pseries/eeh_event.c:64: error: implicit declaration of function 'set_current_state'
  pseries/eeh_event.c:64: error: 'TASK_INTERRUPTIBLE' undeclared (first use in this function)
  pseries/eeh_event.c:64: error: (Each undeclared identifier is reported only once
  pseries/eeh_event.c:64: error: for each function it appears in.)
  pseries/eeh_event.c: In function 'eeh_thread_launcher':
  pseries/eeh_event.c:109: error: 'CLONE_KERNEL' undeclared (first use in this function)

  hotplug-cpu.c: In function 'pseries_mach_cpu_die':
  hotplug-cpu.c:115: error: implicit declaration of function 'idle_task_exit'

  kernel/swsusp_64.c: In function 'do_after_copyback':
  kernel/swsusp_64.c:17: error: implicit declaration of function 'touch_softlockup_watchdog'

  cell/spufs/context.c: In function 'alloc_spu_context':
  cell/spufs/context.c:60: error: implicit declaration of function 'get_task_mm'
  cell/spufs/context.c:60: warning: assignment makes pointer from integer without a cast
  cell/spufs/context.c: In function 'spu_forget':
  cell/spufs/context.c:127: error: implicit declaration of function 'mmput'

  pasemi/dma_lib.c: In function 'pasemi_dma_stop_chan':
  pasemi/dma_lib.c:332: error: implicit declaration of function 'cond_resched'

  sysdev/fsl_lbc.c: In function 'fsl_lbc_ctrl_irq':
  sysdev/fsl_lbc.c:247: error: 'TASK_NORMAL' undeclared (first use in this function)

Add in sched.h so these get the definitions they are looking for.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31 19:30:40 -04:00
Paul Gortmaker b56eade55d powerpc: Fix up implicit stat.h users
They get it via module.h (via device.h) but we want to clean that up.
When we do, we'll get things like:

ibmebus.c:314: error: 'S_IWUSR' undeclared here (not in a function)
vio.c:972: error: 'S_IWUSR' undeclared here (not in a function)

so add in the stat header it is using explicitly in advance.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31 19:30:39 -04:00
Paul Gortmaker 7dfe293cf6 powerpc: Fix up modules that should be including module.h
So that we can clean up the header files and not be relying
on implicit includes from device.h ---> module.h

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31 19:30:38 -04:00
Paul Gortmaker 9308794884 powerpc: include export.h for files using EXPORT_SYMBOL/THIS_MODULE
Fix failures in powerpc associated with the previously allowed
implicit module.h presence that now lead to things like this:

arch/powerpc/mm/mmu_context_hash32.c:76:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/powerpc/mm/tlb_hash32.c:48:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
arch/powerpc/kernel/pci_32.c:51:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/powerpc/kernel/iomap.c:36:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
arch/powerpc/platforms/44x/canyonlands.c:126:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
arch/powerpc/kvm/44x.c:168:59: error: 'THIS_MODULE' undeclared (first use in this function)

[with several contibutions from Stephen Rothwell <sfr@canb.auug.org.au>]

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31 19:30:38 -04:00
Paul Gortmaker 66b15db69c powerpc: add export.h to files making use of EXPORT_SYMBOL
With module.h being implicitly everywhere via device.h, the absence
of explicitly including something for EXPORT_SYMBOL went unnoticed.
Since we are heading to fix things up and clean module.h from the
device.h file, we need to explicitly include these files now.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31 19:30:37 -04:00
Paul Gortmaker 333a151822 powerpc: io-workarounds.c was implicitly getting init_mm
It was coming in via device.h --> module.h etc. but we want to
clean that up.  So explicitly include the header where init_mm
is being declared.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31 19:30:37 -04:00
Paul Bolle 6805ab6daa powerpc: drop unused Kconfig symbols
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Michal Marek <mmarek@suse.cz>
2011-10-31 23:39:52 +01:00
Paul Bolle 21a06da398 powerpc: 40x: drop unused Kconfig symbol
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Josh Boyer <jwboyer@gmail.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
2011-10-31 23:39:52 +01:00
Linus Torvalds 1bc87b0055 Merge branch 'kvm-updates/3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm
* 'kvm-updates/3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm: (75 commits)
  KVM: SVM: Keep intercepting task switching with NPT enabled
  KVM: s390: implement sigp external call
  KVM: s390: fix register setting
  KVM: s390: fix return value of kvm_arch_init_vm
  KVM: s390: check cpu_id prior to using it
  KVM: emulate lapic tsc deadline timer for guest
  x86: TSC deadline definitions
  KVM: Fix simultaneous NMIs
  KVM: x86 emulator: convert push %sreg/pop %sreg to direct decode
  KVM: x86 emulator: switch lds/les/lss/lfs/lgs to direct decode
  KVM: x86 emulator: streamline decode of segment registers
  KVM: x86 emulator: simplify OpMem64 decode
  KVM: x86 emulator: switch src decode to decode_operand()
  KVM: x86 emulator: qualify OpReg inhibit_byte_regs hack
  KVM: x86 emulator: switch OpImmUByte decode to decode_imm()
  KVM: x86 emulator: free up some flag bits near src, dst
  KVM: x86 emulator: switch src2 to generic decode_operand()
  KVM: x86 emulator: expand decode flags to 64 bits
  KVM: x86 emulator: split dst decode to a generic decode_operand()
  KVM: x86 emulator: move memop, memopp into emulation context
  ...
2011-10-30 15:36:45 -07:00
Linus Torvalds acff987d94 Merge branch 'fbdev-next' of git://github.com/schandinat/linux-2.6
* 'fbdev-next' of git://github.com/schandinat/linux-2.6: (270 commits)
  video: platinumfb: Add __devexit_p at necessary place
  drivers/video: fsl-diu-fb: merge diu_pool into fsl_diu_data
  drivers/video: fsl-diu-fb: merge diu_hw into fsl_diu_data
  drivers/video: fsl-diu-fb: only DIU modes 0 and 1 are supported
  drivers/video: fsl-diu-fb: remove unused panel operating mode support
  drivers/video: fsl-diu-fb: use an enum for the AOI index
  drivers/video: fsl-diu-fb: add several new video modes
  drivers/video: fsl-diu-fb: remove broken screen blanking support
  drivers/video: fsl-diu-fb: move some definitions out of the header file
  drivers/video: fsl-diu-fb: fix some ioctls
  video: da8xx-fb: Increased resolution configuration of revised LCDC IP
  OMAPDSS: picodlp: add missing #include <linux/module.h>
  fb: fix au1100fb bitrot.
  mx3fb: fix NULL pointer dereference in screen blanking.
  video: irq: Remove IRQF_DISABLED
  smscufx: change edid data to u8 instead of char
  OMAPDSS: DISPC: zorder support for DSS overlays
  OMAPDSS: DISPC: VIDEO3 pipeline support
  OMAPDSS/OMAP_VOUT: Fix incorrect OMAP3-alpha compatibility setting
  video/omap: fix build dependencies
  ...

Fix up conflicts in:
 - drivers/staging/xgifb/XGI_main_26.c
	Changes to XGIfb_pan_var()
 - drivers/video/omap/{lcd_apollon.c,lcd_ldp.c,lcd_overo.c}
	Removed (or in the case of apollon.c, merged into the generic
	DSS panel in drivers/video/omap2/displays/panel-generic-dpi.c)
2011-10-30 15:30:01 -07:00
Paul Bolle ff5f483f30 powerpc: 4xx: remove commented out Kconfig entries
These Kconfig entries have been commented out ever since commit f6557331
("[...] Re-organize Kconfig code for 4xx in arch/powerpc"). There's no
indication why they're commented out. It looks like they're just "old,
unused [...] config options" that were not removed, as other entries
were in that commit, but only commented out. They might as well be
removed now.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-10-29 21:32:55 +02:00
Linus Torvalds f362f98e7c Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/hch/vfs-queue
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/hch/vfs-queue: (21 commits)
  leases: fix write-open/read-lease race
  nfs: drop unnecessary locking in llseek
  ext4: replace cut'n'pasted llseek code with generic_file_llseek_size
  vfs: add generic_file_llseek_size
  vfs: do (nearly) lockless generic_file_llseek
  direct-io: merge direct_io_walker into __blockdev_direct_IO
  direct-io: inline the complete submission path
  direct-io: separate map_bh from dio
  direct-io: use a slab cache for struct dio
  direct-io: rearrange fields in dio/dio_submit to avoid holes
  direct-io: fix a wrong comment
  direct-io: separate fields only used in the submission path from struct dio
  vfs: fix spinning prevention in prune_icache_sb
  vfs: add a comment to inode_permission()
  vfs: pass all mask flags check_acl and posix_acl_permission
  vfs: add hex format for MAY_* flag values
  vfs: indicate that the permission functions take all the MAY_* flags
  compat: sync compat_stats with statfs.
  vfs: add "device" tag to /proc/self/mountstats
  cleanup: vfs: small comment fix for block_invalidatepage
  ...

Fix up trivial conflict in fs/gfs2/file.c (llseek changes)
2011-10-28 10:49:34 -07:00
Eric W. Biederman 1448c721e4 compat: sync compat_stats with statfs.
This was found by inspection while tracking a similar
bug in compat_statfs64, that has been fixed in mainline
since decemeber.

- This fixes a bug where not all of the f_spare fields
  were cleared on mips and s390.
- Add the f_flags field to struct compat_statfs
- Copy f_flags to userspace in case someone cares.
- Use __clear_user to copy the f_spare field to userspace
  to ensure that all of the elements of f_spare are cleared.
  On some architectures f_spare is has 5 ints and on some
  architectures f_spare only has 4 ints.  Which makes
  the previous technique of clearing each int individually
  broken.

I don't expect anyone actually uses the old statfs system
call anymore but if they do let them benefit from having
the compat and the native version working the same.

Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
2011-10-28 14:58:53 +02:00
Linus Torvalds 3cfef95246 Merge branch 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
  rtmutex: Add missing rcu_read_unlock() in debug_rt_mutex_print_deadlock()
  lockdep: Comment all warnings
  lib: atomic64: Change the type of local lock to raw_spinlock_t
  locking, lib/atomic64: Annotate atomic64_lock::lock as raw
  locking, x86, iommu: Annotate qi->q_lock as raw
  locking, x86, iommu: Annotate irq_2_ir_lock as raw
  locking, x86, iommu: Annotate iommu->register_lock as raw
  locking, dma, ipu: Annotate bank_lock as raw
  locking, ARM: Annotate low level hw locks as raw
  locking, drivers/dca: Annotate dca_lock as raw
  locking, powerpc: Annotate uic->lock as raw
  locking, x86: mce: Annotate cmci_discover_lock as raw
  locking, ACPI: Annotate c3_lock as raw
  locking, oprofile: Annotate oprofilefs lock as raw
  locking, video: Annotate vga console lock as raw
  locking, latencytop: Annotate latency_lock as raw
  locking, timer_stats: Annotate table_lock as raw
  locking, rwsem: Annotate inner lock as raw
  locking, semaphores: Annotate inner lock as raw
  locking, sched: Annotate thread_group_cputimer as raw
  ...

Fix up conflicts in kernel/posix-cpu-timers.c manually: making
cputimer->cputime a raw lock conflicted with the ABBA fix in commit
bcd5cff721 ("cputimer: Cure lock inversion").
2011-10-26 16:17:32 +02:00
Linus Torvalds efb8d21b2c Merge branch 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (79 commits)
  TTY: serial_core: Fix crash if DCD drop during suspend
  tty/serial: atmel_serial: bootconsole removed from auto-enumerates
  Revert "TTY: call tty_driver_lookup_tty unconditionally"
  tty/serial: atmel_serial: add device tree support
  tty/serial: atmel_serial: auto-enumerate ports
  tty/serial: atmel_serial: whitespace and braces modifications
  tty/serial: atmel_serial: change platform_data variable name
  tty/serial: RS485 bindings for device tree
  TTY: call tty_driver_lookup_tty unconditionally
  TTY: pty, release tty in all ptmx_open fail paths
  TTY: make tty_add_file non-failing
  TTY: drop driver reference in tty_open fail path
  8250_pci: Fix kernel panic when pch_uart is disabled
  h8300: drivers/serial/Kconfig was moved
  parport_pc: release IO region properly if unsupported ITE887x card is found
  tty: Support compat_ioctl get/set termios_locked
  hvc_console: display printk messages on console.
  TTY: snyclinkmp: forever loop in tx_load_dma_buffer()
  tty/n_gsm: avoid fifo overflow in gsm_dlci_data_output
  tty/n_gsm: fix a bug in gsm_dlci_data_output (adaption = 2 case)
  ...

Fix up Conflicts in:
 - drivers/tty/serial/8250_pci.c
	Trivial conflict with removed duplicate device ID
 - drivers/tty/serial/atmel_serial.c
	Annoying silly conflict between "specify the port num via
	platform_data" and other changes to atmel_console_init
2011-10-26 15:11:09 +02:00
Linus Torvalds 8a9ea3237e Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1745 commits)
  dp83640: free packet queues on remove
  dp83640: use proper function to free transmit time stamping packets
  ipv6: Do not use routes from locally generated RAs
  |PATCH net-next] tg3: add tx_dropped counter
  be2net: don't create multiple RX/TX rings in multi channel mode
  be2net: don't create multiple TXQs in BE2
  be2net: refactor VF setup/teardown code into be_vf_setup/clear()
  be2net: add vlan/rx-mode/flow-control config to be_setup()
  net_sched: cls_flow: use skb_header_pointer()
  ipv4: avoid useless call of the function check_peer_pmtu
  TCP: remove TCP_DEBUG
  net: Fix driver name for mdio-gpio.c
  ipv4: tcp: fix TOS value in ACK messages sent from TIME_WAIT
  rtnetlink: Add missing manual netlink notification in dev_change_net_namespaces
  ipv4: fix ipsec forward performance regression
  jme: fix irq storm after suspend/resume
  route: fix ICMP redirect validation
  net: hold sock reference while processing tx timestamps
  tcp: md5: add more const attributes
  Add ethtool -g support to virtio_net
  ...

Fix up conflicts in:
 - drivers/net/Kconfig:
	The split-up generated a trivial conflict with removal of a
	stale reference to Documentation/networking/net-modules.txt.
	Remove it from the new location instead.
 - fs/sysfs/dir.c:
	Fairly nasty conflicts with the sysfs rb-tree usage, conflicting
	with Eric Biederman's changes for tagged directories.
2011-10-25 13:25:22 +02:00
Linus Torvalds 59e5253417 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (59 commits)
  MAINTAINERS: linux-m32r is moderated for non-subscribers
  linux@lists.openrisc.net is moderated for non-subscribers
  Drop default from "DM365 codec select" choice
  parisc: Kconfig: cleanup Kernel page size default
  Kconfig: remove redundant CONFIG_ prefix on two symbols
  cris: remove arch/cris/arch-v32/lib/nand_init.S
  microblaze: add missing CONFIG_ prefixes
  h8300: drop puzzling Kconfig dependencies
  MAINTAINERS: microblaze-uclinux@itee.uq.edu.au is moderated for non-subscribers
  tty: drop superfluous dependency in Kconfig
  ARM: mxc: fix Kconfig typo 'i.MX51'
  Fix file references in Kconfig files
  aic7xxx: fix Kconfig references to READMEs
  Fix file references in drivers/ide/
  thinkpad_acpi: Fix printk typo 'bluestooth'
  bcmring: drop commented out line in Kconfig
  btmrvl_sdio: fix typo 'btmrvl_sdio_sd6888'
  doc: raw1394: Trivial typo fix
  CIFS: Don't free volume_info->UNC until we are entirely done with it.
  treewide: Correct spelling of successfully in comments
  ...
2011-10-25 12:11:02 +02:00
Hongjun Chen 1661e5bd55 powerpc/cpm: Clear muram before it is in use.
We need to ensure that MURAM is in a known and cleared out state before
using it as the bootloader could have utilized it from its own purposes
and left it in an unknown state.

If we don't clear it out we've seen issues with UCC ethernet:
* Multi ethernet interfaces can't work simultanously.
* Multi up/down Ethernet interfaces will halt these ports.
* UCC1 RGMII can't work when kernel boots from some hosts.

Signed-off-by: Kai.Jiang <Kai.Jiang@freescale.com>
Signed-off-by: Hongjun Chen <Hong-jun.Chen@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-22 16:15:50 -05:00
Jens Axboe 5c04b426f2 Merge branch 'v3.1-rc10' into for-3.2/core
Conflicts:
	block/blk-core.c
	include/linux/blkdev.h

Signed-off-by: Jens Axboe <axboe@kernel.dk>
2011-10-19 14:30:42 +02:00
Florian Tobias Schandinat 07aaae44f5 Merge commit 'v3.1-rc9' into fbdev-next 2011-10-15 00:14:01 +00:00
Timur Tabi 2bcd1c0cfc powerpc/fsl_msi: add support for "msi-address-64" property
Add support for the msi-address-64 property of a PCI node.  This property
specifies the PCI address of MSIIR (message signaled interrupt index
register).

In commit 3da34aae ("powerpc/fsl: Support unique MSI addresses per PCIe Root
Complex"), the msi_addr_hi/msi_addr_lo fields of struct fsl_msi were redefined
from an actual address to just an offset, but the fields were not renamed
accordingly.  These fields are replace with a single field, msiir_offset,
to reflect the new meaning.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-14 02:54:29 -05:00
Paul Bolle 6af677ea59 Kconfig: remove redundant CONFIG_ prefix on two symbols
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-10-13 18:14:28 +02:00
Kumar Gala 4511680613 powerpc/85xx: Setup secondary cores PIR with hard SMP id
Normally logical and hard cpu ID are the same, however in same cases like
on the P3060 they may differ.  Where the logical is 0..5, the hard id
goes 0,1,4..7.  This can causes issues for places we utilize PIR to index
into array like in debug exception handlers for finding the exception
stack.

Move to setting up PIR with hard_smp_processor_id fixes the issue.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-13 10:19:22 -05:00
Becky Bruce 4559424a0c powerpc/fsl-booke: Fix settlbcam for 64-bit
Currently, it does a cntlzd on the size and then subtracts it from
21.... this doesn't take into account the varying size of a "long".
Just use __ilog instead (and subtract the 10 we have to subtract
to get to the tsize encoding).

Also correct the comment about page sizes supported.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-12 23:39:10 -05:00
Stephen George b9df022319 powerpc/85xx: Adding DCSR node to dtsi device trees
Adding new device tree binding file for the DCSR node.  Modifying device
tree dtsi files to add DCSR node for P2041, P3041, P4080, & P5020.

Signed-off-by: Stephen George <stephen.george@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-11 23:47:29 -05:00
Timur Tabi 499ccb27a8 powerpc/85xx: clean up FPGA device tree nodes for Freecsale QorIQ boards
Standarize and document the FPGA nodes used on Freescale QorIQ reference
boards.  There are different kinds of FPGAs used on the boards, but
only two are currently standard: "pixis", "ngpixis", and "qixis".  Although
there are minor differences among the boards that have one kind of FPGA, most
of the functionality is the same, so it makes sense to create common
compatibility strings.

We also need to update the P1022DS platform file, because the compatible
string for its PIXIS node has changed.  This means that older kernels are
not compatible with newer device trees.  This is not a real problem, however,
since that particular function doesn't work anyway.  When the DIU is active,
the PIXIS is in "indirect mode", and so cannot be accessed as a memory-mapped
device.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-11 23:47:24 -05:00
Anatolij Gustschin 878e3cb5f7 powerpc/85xx: fix PHYS_64BIT selection for P1022DS
Remove wrong CONFIG_ prefix in Kconfig file.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-11 23:42:52 -05:00
Kumar Gala 1dc91c3eb3 powerpc/fsl-booke: Fix setup_initial_memory_limit to not blindly map
On FSL Book-E devices we support multiple large TLB sizes and so we can
get into situations in which the initial 1G TLB size is too big and
we're asked for a size that is not mappable by a single entry (like
512M).  The single entry is important because when we bring up secondary
cores they need to ensure any data structure they need to access (eg
PACA or stack) is always mapped.

So we really need to determine what size will actually be mapped by the
first TLB entry to ensure we limit early memory references to that
region.  We refactor the map_mem_in_cams() code to provider a helper
function that we can utilize to determine the size of the first TLB
entry while taking into account size and alignment constraints.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-11 23:30:41 -05:00
Kumar Gala ba14f64917 powerpc: respect mem= setting for early memory limit setup
For those MMUs that have some form of bolt'd linear mapping (TLB)
required its rare that one ever sets mem= smaller than the size of that
mapping.

However, on Book-E 64 parts the initial linear mapping is quite large
(1G) so its quite reasonable that mem= is set smaller than that.

We need to parse the command line for mem= limit and constrain the
amount of memory we map initially by it if need be.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-11 23:30:40 -05:00
Becky Bruce 5c4a5b8de6 powerpc: Update corenet64_smp_defconfig
Updates from make savedefconfig.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-11 23:28:40 -05:00
Becky Bruce 7c4b2f099f powerpc: Update mpc85xx/corenet 32-bit defconfigs
Results from updates via make savedefconfig.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-11 23:28:38 -05:00
Matthew McClintock de423ff5b0 powerpc/85xx: Fix support for enabling doorbells for IPIs
Commit 765342526246c97600e5344c0949824d94bb51c3 made some small changes to
IPI, message_pass in smp_ops was initialized to NULL for other platforms
but not for 85xx which causes us to always use the mpic for IPI's even
if we support doorbells in HW.

Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-11 23:26:11 -05:00
Bharat Bhushan e33ee8b6f4 powerpc: e500mc: Fix: use CONFIG_PPC_E500MC in idle_e500.S
It is wrongly using undefined CONFIG_E500MC.

Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-11 23:23:24 -05:00
Timur Tabi 2228511833 powerpc/fsl_msi: fix support for multiple MSI ranges
Commit 6820fead ("powerpc/fsl_msi: Handle msi-available-ranges better") added
support for multiple ranges in the msi-available-ranges property, but it
miscalculated the MSIR index when multiple ranges are used.

Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-11 16:18:55 -05:00
Holger Brunck 2a05e333c2 powerpc/82xx: updates for mgcoge
Add:
 - Setup dts node for USB
 - pin description and setup for SMC1 (serial interface)

Update and cleanup mgcoge_defconfig:
- enable: TIPC, UBIFS, USB_GADGET driver, SQUASHFS, HIGHRES timers
          POSIX_MQUEUE, EMBEDDED
- disable: EXT3, PPC_PMAC

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-11 16:18:41 -05:00
David S. Miller 88c5100c28 Merge branch 'master' of github.com:davem330/net
Conflicts:
	net/batman-adv/soft-interface.c
2011-10-07 13:38:43 -04:00
Kumar Gala 37caf9f2a1 powerpc/fsl-booke: Handle L1 D-cache parity error correctly on e500mc
If the L1 D-Cache is in write shadow mode the HW will auto-recover the
error.  However we might still log the error and cause a machine check
(if L1CSR0[CPE] - Cache error checking enable).  We should only treat
the non-write shadow case as non-recoverable.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-06 23:36:55 -05:00
Liu Yu 09af52f78e powerpc/math_emu/efp: Look for errata handler when type mismatches
We already have cpu a005 errata handler when instruction cannot be
recognized.  Before we lookup the inst, there's type checking, and we also
need to handle it in errata handler when the type checking failed.

Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-06 23:36:47 -05:00
Liu Yu d5755e6f3a powerpc/math_emu/efp: No need to round if the result is exact
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-06 23:36:44 -05:00
Liu Yu b430abc4d1 powerpc/math_emu/efp: Use pr_debug instead of printk
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-06 23:36:37 -05:00
Mingkai Hu d31337657b powerpc/85xx: Rename p2040_rdb.c to p2041_rdb.c
There's only p2041rdb board for official release, but the p2041 silicon
on the board can be converted to p2040 silicon without XAUI and L2 cache
function, then the board becomes p2040rdb board. so we use the file name
p2041_rdb.c to handle P2040RDB board and P2041RDB board which is also
consistent with the board name under U-Boot.

During the rename we make few other minor changes to the device tree:
* Move USB phy setting into p2041si.dtsi as its SoC not board defined
* Convert PCI clock-frequency to decimal to be more readable

Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-06 23:32:57 -05:00
Kumar Gala d70cb31de8 powerpc/85xx: Rename PowerPC core nodes to match other e500mc based .dts
The P4080 silicon device tree was using PowerPC,4080 while the other
e500mc based SoCs used PowerPC,e500mc.  Use the core name to be
consistent going forward.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-06 23:32:57 -05:00
Dmitry Eremin-Solenikov 66b77a7540 powerpc/mpc8349emitx: mark localbus as compatible with simple-bus
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-06 23:32:57 -05:00
Dmitry Eremin-Solenikov 385c056b56 powerpc/85xx: sbc8560 - declare that localbus is compatbile with simple-bus
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-06 23:32:57 -05:00
Dmitry Eremin-Solenikov c88f92a261 powerpc/85xx: ksi8560 - declare that localbus is compatbile with simple-bus
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-06 23:32:57 -05:00
Dmitry Eremin-Solenikov c72fa7df37 powerpc/85xx: sbc8560 - correct compilation if CONFIG_PHYS_ADDR_T_64BIT is set
If CONFIG_PHYS_ADDR_T_64BIT is set, compilation of sbc8560 fails with
the following error:

arch/powerpc/platforms/85xx/sbc8560.c: In function ‘sbc8560_bdrstcr_init’:
arch/powerpc/platforms/85xx/sbc8560.c:286: error: format ‘%x’ expects type ‘unsigned int’, but argument 2 has type ‘resource_size_t’

Fix that by using %pR format instead of just printing the start of
resource.

Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-06 23:32:57 -05:00
Timur Tabi c4e5a02327 drivers/video: fsl-diu-fb: only DIU modes 0 and 1 are supported
The Freescale DIU video controller supports five video "modes", but only
the first two are used by the driver.  The other three are special modes
that don't make sense for a framebuffer driver.  Therefore, there's no
point in keeping a global variable that indicates which mode we're
supposed to use.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
2011-10-05 01:10:12 +00:00
Benjamin Herrenschmidt 16fa42affd powerpc: Fix device-tree matching for Apple U4 bridge
Apple Quad G5 has some oddity in it's device-tree which causes the new
generic matching code to fail to relate nodes for PCI-E devices below U4
with their respective struct pci_dev.  This breaks graphics on those
machines among others.

This fixes it using a quirk which copies the node pointer from the host
bridge for the root complex, which makes the generic code work for the
children afterward.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-09-29 19:22:40 -07:00
Heiko Schocher 6ecc07b966 powerpc, tqm5200: update tqm5200_defconfig to fit for charon board.
added:

CONFIG_MTD_OF_PARTS
CONFIG_MTD_PLATRAM
CONFIG_FIXED_PHY
CONFIG_SENSORS_LM80
CONFIG_MFD_SM501
CONFIG_FB
CONFIG_FB_FOREIGN_ENDIAN
CONFIG_FB_SM501
CONFIG_FRAMEBUFFER_CONSOLE
CONFIG_RTC_DRV_DS1374

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-09-29 15:36:33 +02:00
Heiko Schocher 2cafbb37a1 powerpc/5200: add support for charon board
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
[squashed with patch to add sm501 node]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-09-29 15:34:51 +02:00
Benjamin Herrenschmidt 7680057cc4 powerpc: Don't try OPAL takeover on old 970 blades
The firmware on old 970 blades supports some kind of takeover called
"TNK takeover" which will crash if we try to probe for OPAL takeover,
so don't do it.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-29 17:04:59 +10:00
Carl E. Love d15f02eb4e powerpc/perf_event: Fix Power6 L1 cache read & write event codes]
The current L1 cache read event code 0x80082 only counts for thread 0. The
event code 0x280030 should be used to count events on thread 0 and 1. The
patch fixes the event code for the L1 cache read.

The current L1 cache write event code 0x80086 only counts for thread 0. The
event code 0x180032 should be used to count events on thread 0 and 1. The
patch fixes the event code for the L1 cache write.

FYI, the documentation lists three event codes for the L1 cache read event
and three event codes for the L1 cache write event.  The event description
for the event codes is as follows:

L1 cache read requests  0x80082  LSU 0 only
L1 cache read requests  0x8008A  LSU 1 only
L1 cache read requests  0x80030  LSU 1 or LSU 0, counter 2 only.

L1 cache store requests 0x80086  LSU 0 only
L1 cache store requests 0x8008E  LSU 1 only
L1 cache store requests 0x80032  LSU 0 or LSU 1, counter 1 only.

There can only be one request from either LSU 0 or 1 active at a time.

Signed-off-by: Carl Love <cel@us.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-29 17:04:59 +10:00
Benjamin Herrenschmidt e69b742a67 powerpc/ptrace: Fix build with gcc 4.6
gcc (rightfully) complains that we are accessing beyond the
end of the fpr array (we do, to access the fpscr).

The only sane thing to do (whether anything in that code can be
called remotely sane is debatable) is to special case fpscr and
handle it as a separate statement.

I initially tried to do it it by making the array access conditional
to index < PT_FPSCR and using a 3rd else leg but for some reason gcc
was unable to understand it and still spewed the warning.

So I ended up with something a tad more intricated but it seems to
build on 32-bit and on 64-bit with and without VSX.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-29 17:02:04 +10:00
Jimi Xenidis 66857b3a9e powerpc: Fix xmon for systems without MSR[RI]
Based on patch by David Gibson <dwg@au1.ibm.com>

xmon has a longstanding bug on systems which are SMP-capable but lack
the MSR[RI] bit.  In these cases, xmon invoked by IPI on secondary
CPUs will not properly keep quiet, but will print stuff, thereby
garbling the primary xmon's output.  This patch fixes it, by ignoring
the RI bit if the processor does not support it.

There's already a version of this for 4xx upstream, which we'll need
to extend to other RI-lacking CPUs at some point.  For now this adds
Book3e processors to the mix.

Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-29 16:58:22 +10:00
Paul Bolle 395cf9691d doc: fix broken references
There are numerous broken references to Documentation files (in other
Documentation files, in comments, etc.). These broken references are
caused by typo's in the references, and by renames or removals of the
Documentation files. Some broken references are simply odd.

Fix these broken references, sometimes by dropping the irrelevant text
they were part of.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-09-27 18:08:04 +02:00
Benjamin Herrenschmidt bb36c44557 powerpc/pci: Don't configure PCIe settings when PCI_PROBE_ONLY is set
We don't want to configure PCI Express Max Payload Size or
Max Read Request Size on systems that set that flag. The
firmware will have done it for us, and under hypervisors such
as pHyp we don't even see the parent switches and bridges and
thus can make no assumption on what values are safe to use.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-26 14:22:39 +10:00
Paul Mackerras 19ccb76a19 KVM: PPC: Implement H_CEDE hcall for book3s_hv in real-mode code
With a KVM guest operating in SMT4 mode (i.e. 4 hardware threads per
core), whenever a CPU goes idle, we have to pull all the other
hardware threads in the core out of the guest, because the H_CEDE
hcall is handled in the kernel.  This is inefficient.

This adds code to book3s_hv_rmhandlers.S to handle the H_CEDE hcall
in real mode.  When a guest vcpu does an H_CEDE hcall, we now only
exit to the kernel if all the other vcpus in the same core are also
idle.  Otherwise we mark this vcpu as napping, save state that could
be lost in nap mode (mainly GPRs and FPRs), and execute the nap
instruction.  When the thread wakes up, because of a decrementer or
external interrupt, we come back in at kvm_start_guest (from the
system reset interrupt vector), find the `napping' flag set in the
paca, and go to the resume path.

This has some other ramifications.  First, when starting a core, we
now start all the threads, both those that are immediately runnable and
those that are idle.  This is so that we don't have to pull all the
threads out of the guest when an idle thread gets a decrementer interrupt
and wants to start running.  In fact the idle threads will all start
with the H_CEDE hcall returning; being idle they will just do another
H_CEDE immediately and go to nap mode.

This required some changes to kvmppc_run_core() and kvmppc_run_vcpu().
These functions have been restructured to make them simpler and clearer.
We introduce a level of indirection in the wait queue that gets woken
when external and decrementer interrupts get generated for a vcpu, so
that we can have the 4 vcpus in a vcore using the same wait queue.
We need this because the 4 vcpus are being handled by one thread.

Secondly, when we need to exit from the guest to the kernel, we now
have to generate an IPI for any napping threads, because an HDEC
interrupt doesn't wake up a napping thread.

Thirdly, we now need to be able to handle virtual external interrupts
and decrementer interrupts becoming pending while a thread is napping,
and deliver those interrupts to the guest when the thread wakes.
This is done in kvmppc_cede_reentry, just before fast_guest_return.

Finally, since we are not using the generic kvm_vcpu_block for book3s_hv,
and hence not calling kvm_arch_vcpu_runnable, we can remove the #ifdef
from kvm_arch_vcpu_runnable.

Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
2011-09-25 19:52:30 +03:00
Paul Mackerras 0214394760 KVM: PPC: book3s_pr: Simplify transitions between virtual and real mode
This simplifies the way that the book3s_pr makes the transition to
real mode when entering the guest.  We now call kvmppc_entry_trampoline
(renamed from kvmppc_rmcall) in the base kernel using a normal function
call instead of doing an indirect call through a pointer in the vcpu.
If kvm is a module, the module loader takes care of generating a
trampoline as it does for other calls to functions outside the module.

kvmppc_entry_trampoline then disables interrupts and jumps to
kvmppc_handler_trampoline_enter in real mode using an rfi[d].
That then uses the link register as the address to return to
(potentially in module space) when the guest exits.

This also simplifies the way that we call the Linux interrupt handler
when we exit the guest due to an external, decrementer or performance
monitor interrupt.  Instead of turning on the MMU, then deciding that
we need to call the Linux handler and turning the MMU back off again,
we now go straight to the handler at the point where we would turn the
MMU on.  The handler will then return to the virtual-mode code
(potentially in the module).

Along the way, this moves the setting and clearing of the HID5 DCBZ32
bit into real-mode interrupts-off code, and also makes sure that
we clear the MSR[RI] bit before loading values into SRR0/1.

The net result is that we no longer need any code addresses to be
stored in vcpu->arch.

Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
2011-09-25 19:52:29 +03:00
Paul Mackerras 177339d7f7 KVM: PPC: Assemble book3s{,_hv}_rmhandlers.S separately
This makes arch/powerpc/kvm/book3s_rmhandlers.S and
arch/powerpc/kvm/book3s_hv_rmhandlers.S be assembled as
separate compilation units rather than having them #included in
arch/powerpc/kernel/exceptions-64s.S.  We no longer have any
conditional branches between the exception prologs in
exceptions-64s.S and the KVM handlers, so there is no need to
keep their contents close together in the vmlinux image.

In their current location, they are using up part of the limited
space between the first-level interrupt handlers and the firmware
NMI data area at offset 0x7000, and with some kernel configurations
this area will overflow (e.g. allyesconfig), leading to an
"attempt to .org backwards" error when compiling exceptions-64s.S.

Moving them out requires that we add some #includes that the
book3s_{,hv_}rmhandlers.S code was previously getting implicitly
via exceptions-64s.S.

Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
2011-09-25 19:52:28 +03:00
Alexander Graf af8f38b349 KVM: PPC: Add sanity checking to vcpu_run
There are multiple features in PowerPC KVM that can now be enabled
depending on the user's wishes. Some of the combinations don't make
sense or don't work though.

So this patch adds a way to check if the executing environment would
actually be able to run the guest properly. It also adds sanity
checks if PVR is set (should always be true given the current code
flow), if PAPR is only used with book3s_64 where it works and that
HV KVM is only used in PAPR mode.

Signed-off-by: Alexander Graf <agraf@suse.de>
2011-09-25 19:52:27 +03:00
Alexander Graf 930b412a00 KVM: PPC: Enable the PAPR CAP for Book3S
Now that Book3S PV mode can also run PAPR guests, we can add a PAPR cap and
enable it for all Book3S targets. Enabling that CAP switches KVM into PAPR
mode.

Signed-off-by: Alexander Graf <agraf@suse.de>
2011-09-25 19:52:26 +03:00
Alexander Graf a668f2bd3f KVM: PPC: Support SC1 hypercalls for PAPR in PR mode
PAPR defines hypercalls as SC1 instructions. Using these, the guest modifies
page tables and does other privileged operations that it wouldn't be allowed
to do in supervisor mode.

This patch adds support for PR KVM to trap these instructions and route them
through the same PAPR hypercall interface that we already use for HV style
KVM.

Signed-off-by: Alexander Graf <agraf@suse.de>
2011-09-25 19:52:25 +03:00
Alexander Graf aacf9aa3a7 KVM: PPC: Stub emulate CFAR and PURR SPRs
Recent Linux versions use the CFAR and PURR SPRs, but don't really care about
their contents (yet). So for now, we can simply return 0 when the guest wants
to read them.

Signed-off-by: Alexander Graf <agraf@suse.de>
2011-09-25 19:52:25 +03:00
Alexander Graf 0254f07429 KVM: PPC: Add PAPR hypercall code for PR mode
When running a PAPR guest, we need to handle a few hypercalls in kernel space,
most prominently the page table invalidation (to sync the shadows).

So this patch adds handling for a few PAPR hypercalls to PR mode KVM. I tried
to share the code with HV mode, but it ended up being a lot easier this way
around, as the two differ too much in those details.

Signed-off-by: Alexander Graf <agraf@suse.de>

---

v1 -> v2:

  - whitespace fix
2011-09-25 19:52:24 +03:00
Alexander Graf a15bd354f0 KVM: PPC: Add support for explicit HIOR setting
Until now, we always set HIOR based on the PVR, but this is just wrong.
Instead, we should be setting HIOR explicitly, so user space can decide
what the initial HIOR value is - just like on real hardware.

We keep the old PVR based way around for backwards compatibility, but
once user space uses the SREGS based method, we drop the PVR logic.

Signed-off-by: Alexander Graf <agraf@suse.de>
2011-09-25 19:52:23 +03:00
Alexander Graf 77e675ad82 KVM: PPC: Read out syscall instruction on trap
We have a few traps where we cache the instruction that cause the trap
for analysis later on. Since we now need to be able to distinguish
between SC 0 and SC 1 system calls and the only way to find out which
is which is by looking at the instruction, we also read out the instruction
causing the system call.

Signed-off-by: Alexander Graf <agraf@suse.de>
2011-09-25 19:52:22 +03:00
Alexander Graf 04fcc11bb5 KVM: PPC: Interpret SDR1 as HVA in PAPR mode
When running a PAPR guest, the guest is not allowed to set SDR1 - instead
the HTAB information is held in internal hypervisor structures. But all of
our current code relies on SDR1 and walking the HTAB like on real hardware.

So in order to not be too intrusive, we simply set SDR1 to the HTAB we hold
in host memory. That way we can keep the HTAB in user space, but use it from
kernel space to map the guest.

Signed-off-by: Alexander Graf <agraf@suse.de>
2011-09-25 19:52:21 +03:00
Alexander Graf 317a8fa304 KVM: PPC: Check privilege level on SPRs
We have 3 privilege levels: problem state, supervisor state and hypervisor
state. Each of them can access different SPRs, so we need to check on every
SPR if it's accessible in the respective mode.

Signed-off-by: Alexander Graf <agraf@suse.de>
2011-09-25 19:52:20 +03:00
Alexander Graf 9432ba6015 KVM: PPC: Add papr_enabled flag
When running a PAPR guest, some things change. The privilege level drops
from hypervisor to supervisor, SDR1 gets treated differently and we interpret
hypercalls. For bisectability sake, add the flag now, but only enable it when
all the support code is there.

Signed-off-by: Alexander Graf <agraf@suse.de>
2011-09-25 19:52:19 +03:00
Alexander Graf db507c300e KVM: PPC: move compute_tlbie_rb to book3s common header
We need the compute_tlbie_rb in _pr and _hv implementations for papr
soon, so let's move it over to a common header file that both
implementations can leverage.

Signed-off-by: Alexander Graf <agraf@suse.de>
2011-09-25 19:52:18 +03:00
Thadeu Lima de Souza Cascardo d12b524f8b powerpc: Reserve iommu page 0
Some devices have a dma-window that starts at the address 0. This allows
DMA addresses to be mapped to this address and returned to drivers as a
valid DMA address. Some drivers may not behave well in this case, since
the address 0 is considered an error or not allocated.

The solution to avoid this kind of error from happening is reserve the
page addressed as 0 so it cannot be allocated for a DMA mapping.

Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-23 10:27:03 +10:00
Paul Mackerras 25c29f9e32 powerpc: Fix hugetlb with CONFIG_PPC_MM_SLICES=y
Commit 41151e77a4 ("powerpc: Hugetlb for BookE") added some
#ifdef CONFIG_MM_SLICES conditionals to hugetlb_get_unmapped_area()
and vma_mmu_pagesize().  Unfortunately this is not the correct config
symbol; it should be CONFIG_PPC_MM_SLICES.  The result is that
attempting to use hugetlbfs on 64-bit Power server processors results
in an infinite stack recursion between get_unmapped_area() and
hugetlb_get_unmapped_area().

This fixes it by changing the #ifdef to use CONFIG_PPC_MM_SLICES
in those functions and also in book3e_hugetlb_preload().

Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-23 10:21:33 +10:00
Wolfram Sang 7b72c9f875 powerpc: update 512x-defconfig
Activate all MPC512x related boards. Also enable GPIO-driver, SPI driver
and at25 to test SPI. Enable DEVTMPFS. Bump to 3.1-rc6.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-09-23 00:20:07 +02:00
Wolfram Sang c68308dd50 gpio: move mpc8xxx/512x gpio driver to drivers/gpio
Move the driver to the place where it is expected to be nowadays. Also
rename its CONFIG-name to match the rest and adapt the defconfigs.
Finally, move selection of REQUIRE_GPIOLIB or WANTS_OPTIONAL_GPIOLIB to
the platforms, because this option is per-platform and not per-driver.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-09-23 00:14:15 +02:00
Timur Tabi 40dc7e8b4a powerpc/5200: enable audio in the defconfig
Audio support for the MPC5200 exists, so enable it by default.

Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-09-22 23:24:06 +02:00
Anatolij Gustschin 5d9e6ac843 powerpc/5200: dts: digsy_mtc.dts: enable both MSCAN nodes
We use both MSCAN controllers on this board, so do not disable
them in the device tree.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-09-22 23:18:33 +02:00
Anatolij Gustschin 1982c09a64 powerpc/5200: dts: digsy_mtc.dts: add timer0 and timer1 gpio properties
timer0 and timer1 pins are used as simple GPIO on this board.
Add gpio-controller and #gpio-cells properties to timer nodes
so that we can control gpio lines using available MPC52xx
GPT driver.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-09-22 23:14:03 +02:00
Anatolij Gustschin aa4593f274 powerpc/5200: dts: digsy_mtc.dts: update to add can, pci, serial and spi
Add new nodes to describe more hardware the board is
equipped with:
 - two can nodes for SJA1000 on localbus
 - pci node to support Coral-PA graphics controller
 - serial node for SC28L92 DUART on localbus
 - spi node for MSP430 device

Also correct i2c eeprom node name.

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-09-22 23:13:50 +02:00
Anatolij Gustschin 6cf1d0b806 powerpc/5200: mpc5200b.dtsi: add spi node address- and size-cells properties
Both, #address-cells and #size-cells properties are required
for spi bus node, so add them.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-09-22 23:13:40 +02:00
David S. Miller 8decf86879 Merge branch 'master' of github.com:davem330/net
Conflicts:
	MAINTAINERS
	drivers/net/Kconfig
	drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c
	drivers/net/ethernet/broadcom/tg3.c
	drivers/net/wireless/iwlwifi/iwl-pci.c
	drivers/net/wireless/iwlwifi/iwl-trans-tx-pcie.c
	drivers/net/wireless/rt2x00/rt2800usb.c
	drivers/net/wireless/wl12xx/main.c
2011-09-22 03:23:13 -04:00
Anshuman Khandual a120db06c3 perf events, powerpc: Add POWER7 stalled-cycles-frontend/backend events
perf events, powerpc: Add POWER7 stalled-cycles-frontend/backend events

Extent the POWER7 PMU driver with definitions for generic front-end and back-end
stall events.

As explained in Ingo's original comment(8f62242246
), the exact definitions of the stall events are very much processor specific as

different things mean different in their respective instruction pipeline. These
two Power7 raw events are the closest approximation to the concept detailed in
Ingo's comment.

[PERF_COUNT_HW_STALLED_CYCLES_FRONTEND] = 0x100f8, /* GCT_NOSLOT_CYC */
It means cycles when the Global Completion Table has no slots from this thread

[PERF_COUNT_HW_STALLED_CYCLES_BACKEND] = 0x4000a,  /* CMPLU_STALL */
It means no groups completed and GCT not empty for this thread

Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 16:12:56 +10:00
Benjamin Herrenschmidt 82ba129bae powerpc/powernv: Handle PCI-X/PCIe reset delay
The firmware doesn't wait after lifting the PCI reset. However it does
timestamp it in the device tree. We use that to ensure we wait long
enough (3s is our current arbitrary setting) from that timestamp to
actually probing the bus.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 16:12:54 +10:00
Benjamin Herrenschmidt c1a2562ac5 powerpc/powernv: Implement MSI support for p5ioc2 PCIe
This implements support for MSIs on p5ioc2 PHBs. We only support
MSIs on the PCIe PHBs, not the PCI-X ones as the later hasn't been
properly verified in HW.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 16:12:44 +10:00
Benjamin Herrenschmidt 61305a96fa powerpc/powernv: Add support for p5ioc2 PCI-X and PCIe
This adds support for PCI-X and PCIe on the p5ioc2 IO hub using
OPAL. This includes allocating & setting up TCE tables and config
space access routines.

This also supports fallbacks via RTAS when OPAL is absent, using
legacy TCE format pre-allocated via the device-tree (BML style)

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 16:10:04 +10:00
Benjamin Herrenschmidt ed79ba9e15 powerpc/powernv: Machine check and other system interrupts
OPAL can handle various interrupt for us such as Machine Checks (it
performs all sorts of recovery tasks and passes back control to us with
informations about the error), Hardware Management Interrupts and Softpatch
interrupts.

This wires up the mechanisms and prints out specific informations returned
by HAL when a machine check occurs.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 16:10:03 +10:00
Benjamin Herrenschmidt a125e0928c powerpc/powernv: Register and handle OPAL interrupts
We do the minimum which is to "pass" interrupts to HAL, which
makes the console smoother and will allow us to implement
interrupt based completion and console.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 16:10:01 +10:00
Benjamin Herrenschmidt 5c7c1e9444 powerpc/powernv: Add OPAL ICS backend
OPAL handles HW access to the various ICS or equivalent chips
for us (with the exception of p5ioc2 based HEA which uses a

different backend) similarily to what RTAS does on pSeries.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 16:09:59 +10:00
Benjamin Herrenschmidt 628daa8d5a powerpc/powernv: Add RTC and NVRAM support plus RTAS fallbacks
Implements OPAL RTC and NVRAM support and wire all that up to
the powernv platform.

We use RTAS for RTC as a fallback if available. Using RTAS for nvram
is not supported yet, pending some rework/cleanup and generalization
of the pSeries & CHRP code. We also use RTAS fallbacks for power off
and reboot

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 16:09:57 +10:00
Benjamin Herrenschmidt ec27329ffb powerpc/powernv: Hookup reboot and poweroff functions
This calls the respective HAL functions, and spin on hal_poll_event()
to ensure the HAL has a chance to communicate with the FSP to trigger
the reboot or shutdown operation

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 16:09:55 +10:00
Benjamin Herrenschmidt daea1175a9 powerpc/powernv: Support for OPAL console
This adds a udbg and an hvc console backend for supporting a console
using the OPAL console interfaces.

On OPAL v1 we have hvc0 mapped to whatever console the system was
configured for (network or hvsi serial port) via the service
processor.

On OPAL v2 we have hvcN mapped to the Nth console provided by OPAL
which generally corresponds to:

	hvc0 : network console (raw protocol)
	hvc1 : serial port S1 (hvsi)
	hvc2 : serial port S2 (hvsi)

Note: At this point, early debug console only works with OPAL v1
and shouldn't be enabled in a normal kernel.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 16:09:54 +10:00
Benjamin Herrenschmidt 6e35d5dac0 powerpc/powernv: Add support for instanciating OPAL v2 from Open Firmware
OPAL v2 is instantiated in a way similar to RTAS using Open Firmware
client interface calls, and the resulting address and entry point are
put in the device-tree

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 16:09:52 +10:00
Benjamin Herrenschmidt 14a43e69ed powerpc/powernv: Basic support for OPAL
Add definition of OPAL interfaces along with  the wrappers to call
into OPAL runtime and the early device-tree parsing hook to locate
the OPAL runtime firmware.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 16:09:50 +10:00
Benjamin Herrenschmidt 817c21ad9a powerpc/powernv: Get kernel command line accross OPAL takeover
We stash it in boot_command_line which isn't in BSS and so won't
be overwritten. We then use that as a default cmd_line before
we walk the device-tree.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 16:09:48 +10:00
Benjamin Herrenschmidt 27f4488872 powerpc/powernv: Add OPAL takeover from PowerVM
On machines supporting the OPAL firmware version 1, the system
is initially booted under pHyp. We then use a special hypercall
to verify if OPAL is available and if it is, we then trigger
a "takeover" which disables pHyp and loads the OPAL runtime
firmware, giving control to the kernel in hypervisor mode.

This patch add the necessary code to detect that the OPAL takeover
capability is present when running under PowerVM (aka pHyp) and
perform said takeover to get hypervisor control of the processor.

To perform the takeover, we must first use RTAS (within Open
Firmware runtime environment) to start all processors & threads,
in order to give control to OPAL on all of them. We then call
the takeover hypercall on everybody, OPAL will re-enter the kernel
main entry point passing it a flat device-tree.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 16:09:47 +10:00
Benjamin Herrenschmidt 344eb010b2 powerpc/powernv: Add CPU hotplug support
Unplugged CPU go into NAP mode in a loop until woken up

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 16:09:45 +10:00
Benjamin Herrenschmidt 55190f8878 powerpc: Add skeleton PowerNV platform
This adds a skeletton for the new Power "Non Virtualized"
platform which will be used by machines supporting running
without an hypervisor, for example in order to run KVM.

These machines will be using a new firmware called OPAL
for which the support will be provided by later patches.

The PowerNV platform is intended to be also usable under
the BML environment used internally for early CPU bringup
which is why the code also supports using RTAS instead of
OPAL in various places.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 15:53:25 +10:00
Benjamin Herrenschmidt e550592e68 powerpc/powernv: Don't clobber r9 in relative_toc()
With OPAL, r8 and r9 will be used to pass the OPAL base and entry
for debugging purposes (those informations are also in the
device-tree). We don't want to clobber those registers that
early.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 15:53:24 +10:00
Benjamin Herrenschmidt 781fb7a3e4 powerpc/pci: Call pcie_bus_configure_settings()
This new function is used to properly setup the PCI Express Max Payload Size
(and in some circumstances Max Read Request Size).

Some systems will not operate properly if these aren't set correctly and
the firmware doesn't always do it.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 15:53:24 +10:00
Benjamin Herrenschmidt fb82b83970 powerpc/smp: More generic support for "soft hotplug"
This adds more generic support for doing CPU hotplug with a simple
idle loop and no actual reset of the processors. The generic
smp_generic_kick_cpu() does the hotplug bringup trick if the PACA
shows that the CPU has already been started at boot and we provide
an accessor for the CPU state.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 15:53:24 +10:00
Benjamin Herrenschmidt b8bb922c68 powerpc/udbg: Fix Kconfig entry for avoiding 44x early debug with KVM
It was preventing the global early debug selection whenever KVM was enabled
instead of only preventing the 440 specific one.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 15:53:24 +10:00
Anton Blanchard 8bdafa39a4 powerpc: Fix deadlock in icswx code
The icswx code introduced an A-B B-A deadlock:

     CPU0                    CPU1
     ----                    ----
lock(&anon_vma->mutex);
                             lock(&mm->mmap_sem);
                             lock(&anon_vma->mutex);
lock(&mm->mmap_sem);

Instead of using the mmap_sem to keep mm_users constant, take the
page table spinlock.

Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 15:53:23 +10:00
Anton Blanchard a11940978b powerpc: Fix oops when echoing bad values to /sys/devices/system/memory/probe
If we echo an address the hypervisor doesn't like to
/sys/devices/system/memory/probe we oops the box:

# echo 0x10000000000 > /sys/devices/system/memory/probe

kernel BUG at arch/powerpc/mm/hash_utils_64.c:541!

The backtrace is:

create_section_mapping
arch_add_memory
add_memory
memory_probe_store
sysdev_class_store
sysfs_write_file
vfs_write
SyS_write

In create_section_mapping we BUG if htab_bolt_mapping returned
an error. A better approach is to return an error which will
propagate back to userspace.

Rerunning the test with this patch applied:

# echo 0x10000000000 > /sys/devices/system/memory/probe
-bash: echo: write error: Invalid argument

Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 15:53:23 +10:00
Anton Blanchard dfbe93a222 powerpc: Coding style cleanups
While converting code to use for_each_node_by_type I noticed a
number of coding style issues.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 15:53:23 +10:00
Anton Blanchard 94db7c5e14 powerpc: Use for_each_node_by_type instead of open coding it
Use for_each_node_by_type instead of open coding it.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 15:53:23 +10:00
Anton Blanchard 6083184269 powerpc/numa: Remove double of_node_put in hot_add_node_scn_to_nid
During memory hotplug testing, I got the following warning:

ERROR: Bad of_node_put() on /memory@0

of_node_release
kref_put
of_node_put
of_find_node_by_type
hot_add_node_scn_to_nid
hot_add_scn_to_nid
memory_add_physaddr_to_nid
...

of_find_node_by_type() loop does the of_node_put for us so we only
need the handle the case where we terminate the loop early.

As suggested by Stephen Rothwell we can do the of_node_put
unconditionally outside of the loop since of_node_put handles a
NULL argument fine.

Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 15:53:22 +10:00
Anton Blanchard e377bc5d49 powerpc/numa: Remove duplicate RECLAIM_DISTANCE definition
We have two identical definitions of RECLAIM_DISTANCE, looks like
the patch got applied twice. Remove one.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 15:53:22 +10:00
Anton Blanchard 7bebcf0925 powerpc/numa: Disable NEWIDLE balancing at node level
On big POWER7 boxes we see large amounts of CPU time in system
processes like workqueue and watchdog kernel threads.

We currently rebalance the entire machine each time a task goes
idle and this is very expensive on large machines. Disable newidle
balancing at the node level and rely on the scheduler tick to
rebalance across nodes.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 15:53:22 +10:00
Anton Blanchard d4761ad2ef powerpc/numa: Increase SD_NODES_PER_DOMAIN to 32.
The largest POWER7 boxes have 32 nodes. SD_NODES_PER_DOMAIN groups
nodes into chunks of 16 and adds a global balancing domain
(SD_ALLNODES) above it.

If we bump SD_NODES_PER_DOMAIN to 32, then we avoid this extra
level of balancing on our largest boxes.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 15:53:22 +10:00
Anton Blanchard a200d8e446 powerpc/numa: Enable SD_WAKE_AFFINE in node definition
When chasing a performance issue on ppc64, I noticed tasks
communicating via a pipe would often end up on different nodes.

It turns out SD_WAKE_AFFINE is not set in our node defition. Commit
9fcd18c9e6 (sched: re-tune balancing) enabled SD_WAKE_AFFINE
in the node definition for x86 and we need a similar change for
ppc64.

I used lmbench lat_ctx and perf bench pipe to verify this fix. Each
benchmark was run 10 times and the average taken.

lmbench lat_ctx:

before:  66565 ops/sec
after:  204700 ops/sec

3.1x faster

perf bench pipe:

before: 5.6570 usecs
after:  1.3470 usecs

4.2x faster

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 15:53:21 +10:00
Benjamin Herrenschmidt 1cce058b29 Merge remote-tracking branch 'origin/master' into next
(Merge in order to get the PCIe mps/mrss code fixes)
2011-09-20 15:52:38 +10:00
Hector Martin c26afe9e85 powerpc/ps3: Add gelic udbg driver
Add a new udbg driver for the PS3 gelic Ehthernet device.

This driver shares only a few stucture and constant definitions with the
gelic Ethernet device driver, so is implemented as a stand-alone driver
with no dependencies on the gelic Ethernet device driver.

Signed-off-by: Hector Martin <hector@marcansoft.com>
Signed-off-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 09:20:05 +10:00
Thadeu Lima de Souza Cascardo 8feaa43494 powerpc/eeh: Fix /proc/ppc64/eeh creation
Since commit 188917e183, /proc/ppc64 is a
symlink to /proc/powerpc/. That means that creating /proc/ppc64/eeh will
end up with a unaccessible file, that is not listed under /proc/powerpc/
and, then, not listed under /proc/ppc64/.

Creating /proc/powerpc/eeh fixes that problem and maintain the
compatibility intended with the ppc64 symlink.

Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <stable@kernel.org>	[3.x]
2011-09-20 09:20:03 +10:00
Arnaud Lacombe cf01a404d9 powerpc/xics: Add __init to marker icp_native_init()
This should fix the following warning:

 LD      arch/powerpc/sysdev/xics/built-in.o
WARNING: arch/powerpc/sysdev/xics/built-in.o(.text+0x1310): Section mismatch in
reference from the function .icp_native_init() to the function
.init.text:.icp_native_init_one_node()
The function .icp_native_init() references
the function __init .icp_native_init_one_node().
This is often because .icp_native_init lacks a __init
annotation or the annotation of .icp_native_init_one_node is wrong.

icp_native_init() is only referenced in `arch/powerpc/sysdev/xics/xics-common.c'
by xics_init() which is itself marked with __init.

= not built-tested =

Reported-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 09:20:02 +10:00
Anton Blanchard 9c740025c5 powerpc/pseries: Avoid spurious error during hotplug CPU add
During hotplug CPU add we get the following error:

Unexpected Error (0) returned from configure-connector

ibm,configure-connector returns 0 for configuration complete, so
catch this and avoid the error.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <stable@kernel.org>
2011-09-20 09:20:00 +10:00
Tang Yuantian 0330581ab3 powerpc/mm: Fix the call trace when resumed from hibernation
In SMP mode, the kernel would produce call trace when resumed
	from hibernation. The reason is when the function destroy_context
	is called to drop the resuming mm context, the mm->context.active
	is 1 which is wrong and should be zero.
	We pass the current->active_mm as previous mm context to function
	switch_mmu_context to decrease the context.active by 1.

	In UP mode, there is no effect.

Signed-off-by: Tang Yuantian <b29983@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 09:19:58 +10:00
Tony Breeds 9c57a32b2f powerpc/4xx/pci: Add __init annotations for *init_port_hw() functions.
The various port_init_hw methods of ppc4xx_pciex_hwops should have been
marked __init and when I added ppc4xx_pciex_port_reset_sdr(), which is
__init.  This added many section mismatch warnings like:

WARNING: arch/powerpc/sysdev/built-in.o(.text+0x5c68): Section mismatch in reference from the function ppc440spe_pciex_init_port_hw() to the function .init.text:ppc4xx_pciex_port_reset_sdr()
The function ppc440spe_pciex_init_port_hw() references
the function __init ppc4xx_pciex_port_reset_sdr().
This is often because ppc440spe_pciex_init_port_hw lacks a __init
annotation or the annotation of ppc4xx_pciex_port_reset_sdr is wrong.

Trivial patch to silence those warnings.

Reported-By: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>

Yours Tony
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 09:19:56 +10:00
Michael Ellerman f9a71e0fd1 powerpc/wsp: Add MSI support for PCI on PowerEN
Based on a patch by Michael Ellerman <michael@ellerman.id.au>

Patch was simply forward ported upstream.

Jimi Xenidis <jimix@pobox.com>

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 09:19:55 +10:00
Benjamin Herrenschmidt f352c72512 powerpc/wsp: Add PCIe Root support to PowerEN/WSP
Based on a patch by Benjamin Herrenschmidt <benh@kernel.crashing.org>

Modernized and slightly modified to not record erros into the nvram
log since we do not have that device driver just yet.

Jimi Xenidis <jimix@pobox.com>

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 09:19:53 +10:00
Jimi Xenidis 2fa3d9e5c6 powerpc/wsp: Fix Wire Speed Processor platform configs
Some config selections were applied to the platform (reference board)
when they actuall apply to the chip.

Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 09:19:51 +10:00
Julia Lawall 7a19081fc2 pseries/iommu: Add missing kfree
At this point, window has not been stored anywhere, so it has to be freed
before leaving the function.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@exists@
local idexpression x;
statement S,S1;
expression E;
identifier fl;
expression *ptr != NULL;
@@

x = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
     when != if (...) { <+...kfree(x)...+> }
     when any
     when != true x == NULL
x->fl
...>
(
if (x == NULL) S1
|
if (...) { ... when != x
               when forall
(
 return \(0\|<+...x...+>\|ptr\);
|
* return ...;
)
}
)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 09:19:49 +10:00
Scott Wood 6dece0eb69 powerpc/32: Pass device tree address as u64 to machine_init
u64 is used rather than phys_addr_t to keep things simple, as
this is called from assembly code.

Update callers to pass a 64-bit address in r3/r4.  Other unused
register assignments that were once parameters to machine_init
are dropped.

For FSL BookE, look up the physical address of the device tree from the
effective address passed in r3 by the loader.  This is required for
situations where memory does not start at zero (due to AMP or IOMMU-less
virtualization), and thus the IMA doesn't start at zero, and thus the
device tree effective address does not equal the physical address.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 09:19:47 +10:00
Jim Keniston 6c493685f1 powerpc/nvram: Add compression to fit more oops output into NVRAM
Capture more than twice as much text from the printk buffer, and
compress it to fit it in the lnx,oops-log NVRAM partition.  You
can view the compressed text using the new (as of July 20) --unzip
option of the nvram command in the powerpc-utils package.

[BenH: Added select of ZLIB_DEFLATE]

Signed-off-by: Jim Keniston <jkenisto@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 09:19:46 +10:00
Matthew McClintock 7392769365 powerpc: Fix build dependencies for epapr.c which needs libfdt.h
Currently, the build can (very rarely) fail to build because libfdt.h has
not been created or is in the process of being copied.

Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 09:19:44 +10:00
Timur Tabi 14b9247019 powerpc/mpic: Add support for discontiguous cores
There is one place in the MPIC driver that assumes that the cores are numbered
from 0 to n-1.  However, this is not true if the CPUs are not numbered
sequentially.  This can happen on a eight-core SOC where cores two and three
are removed in the device tree.  So instead of blindly looping, we iterate
over the discovered CPUs and use the SMP ID as the index.

This means that we no longer ask the MPIC how many CPUs there are, so
we also delete mpic->num_cpus.

We also catch if the number of CPUs in the SOC exceeds the number that the
MPIC supports.  This should never happen, of course, but it's good to be
sure.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 09:19:42 +10:00
Becky Bruce 41151e77a4 powerpc: Hugetlb for BookE
Enable hugepages on Freescale BookE processors.  This allows the kernel to
use huge TLB entries to map pages, which can greatly reduce the number of
TLB misses and the amount of TLB thrashing experienced by applications with
large memory footprints.  Care should be taken when using this on FSL
processors, as the number of large TLB entries supported by the core is low
(16-64) on current processors.

The supported set of hugepage sizes include 4m, 16m, 64m, 256m, and 1g.
Page sizes larger than the max zone size are called "gigantic" pages and
must be allocated on the command line (and cannot be deallocated).

This is currently only fully implemented for Freescale 32-bit BookE
processors, but there is some infrastructure in the code for
64-bit BooKE.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 09:19:40 +10:00
Arnd Bergmann 7df5659eef serial/8250: Move UPIO_TSI to powerpc
This iotype is only used by the legacy_serial code in powerpc, so the
code should live there, rather than be compiled in for every 8250
driver.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: linux-serial@vger.kernel.org
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 09:19:39 +10:00
Milton Miller 2eccacd097 powerpc: Tidy up dma_map_ops after adding new hook
The new get_required_mask hook name is longer than many of but not all
of the prior ops.  Tidy the struct initializers to align the equal signs
using the local whitespace.

Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Cc: benh@kernel.crashing.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 09:19:37 +10:00
Milton Miller d24f9c6999 powerpc: Use the newly added get_required_mask dma_map_ops hook
Now that the generic code has dma_map_ops set, instead of having a
messy ifdef & if block in the base dma_get_required_mask hook push
the computation into the dma ops.

If the ops fails to set the get_required_mask hook default to the
width of dma_addr_t.

This also corrects ibmbus ibmebus_dma_supported to require a 64
bit mask.  I doubt anything is checking or setting the dma mask on
that bus.

Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Cc: benh@kernel.crashing.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-20 09:19:35 +10:00
Jiri Kosina e060c38434 Merge branch 'master' into for-next
Fast-forward merge with Linus to be able to merge patches
based on more recent version of the tree.
2011-09-15 15:08:18 +02:00
Vitaliy Ivanov fb914ebff5 treewide: typo 'interrrupt' word corrections.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Vitaliy Ivanov <vitalivanov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-09-15 14:13:02 +02:00
Thomas Gleixner bccc2f7b4c locking, powerpc: Annotate uic->lock as raw
uic->lock is protecting the interrupt controller hardware. This lock
can not be preempted on -rt.

In mainline this change documents the low level nature of
the lock - otherwise there's no functional difference. Lockdep
and Sparse checking will work as usual.

Reported-by: Darcy L. Watkins <dwatkins@tranzeo.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2011-09-13 11:12:10 +02:00
Christoph Hellwig 5a7bbad27a block: remove support for bio remapping from ->make_request
There is very little benefit in allowing to let a ->make_request
instance update the bios device and sector and loop around it in
__generic_make_request when we can archive the same through calling
generic_make_request from the driver and letting the loop in
generic_make_request handle it.

Note that various drivers got the return value from ->make_request and
returned non-zero values for errors.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
2011-09-12 12:12:01 +02:00
Milton Miller 6a5c7be5e4 powerpc: Override dma_get_required_mask by platform hook and ops
The hook dma_get_required_mask is supposed to return the mask required
by the platform to operate efficently.  The generic version of
dma_get_required_mask in driver/base/platform.c returns a mask based
only on max_pfn.  However, this is likely too big for iommu systems
and could be too small for platforms that require a dma offset or have
a secondary window at a high offset.

Override the default, provide a hook in ppc_md used by pseries lpar and
cell, and provide the default answer based on memblock_end_of_DRAM(),
with hooks for get_dma_offset, and provide an implementation for iommu
that looks at the defined table size.  Coverting from the end address
to the required bit mask is based on the generic implementation.

The need for this was discovered when the qla2xxx driver switched to
64 bit dma then reverted to 32 bit when dma_get_required_mask said
32 bits was sufficient.

Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Cc: benh@kernel.crashing.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-09-01 16:00:19 +10:00
Benjamin Herrenschmidt 7bfb40b048 Merge remote-tracking branch 'origin/master' into next
(Pickup Stephen's fix d4d7b2a11c)
2011-09-01 15:57:32 +10:00
Linus Torvalds e9208a4eec Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/p1023rds: Fix the error of bank-width of nor flash
  powerpc/85xx: enable caam crypto driver by default
  powerpc/85xx: enable the audio drivers in the defconfigs
2011-08-31 08:58:36 -07:00
Chunhe Lan 0c81e4b426 powerpc/p1023rds: Fix the error of bank-width of nor flash
In the p1023rds, a physical bus of nor flash is 16 bits width.
The bank-width is width (in bytes) of the bus width. So, the
value of bank-width of nor flash is not one, and it should be
two.

Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-08-30 21:27:33 -05:00
Kim Phillips e09e2fb513 powerpc/85xx: enable caam crypto driver by default
corenet based SoCs have SEC4 h/w, so enable the SEC4 driver,
caam, and the algorithms it supports, and disable the
SEC2/3 driver, talitos.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-08-30 21:27:30 -05:00
Timur Tabi 39c428f753 powerpc/85xx: enable the audio drivers in the defconfigs
Enable the audio drivers in the non-corenet 85xx defconfigs so that audio
is enabled on the Freescale P1022DS reference board.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-08-30 21:27:29 -05:00
Benjamin Herrenschmidt 9bb7361d99 Merge remote-tracking branch 'jwb/next' into next 2011-08-30 15:14:46 +10:00
Stephen Rothwell d4d7b2a11c remove remaining references to nfsservctl
These were missed in commit f5b9409973 "All Arch: remove linkage
for sys_nfsservctl system call" due to them having no sys_ prefix
(presumably).

Cc: NeilBrown <neilb@suse.de>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-parisc@vger.kernel.org
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: James Bottomley <James.Bottomley@hansenpartnership.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-08-29 16:31:59 -07:00
Florian Tobias Schandinat d4a7dbfdf1 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-3.x into fbdev-next
Conflicts:
	drivers/video/atmel_lcdfb.c
2011-08-29 09:14:30 +00:00
Liu Gang-B34182 671ee7f0ce arch/powerpc/sysdev/fsl_rio.c: correct IECSR register clear value
This bug causes the IECSR register clear failure.  In this case, the RETE
(retry error threshold exceeded) interrupt will be generated and cannot be
cleared.  So the related ISR may be called persistently.

The RETE bit in IECSR is cleared by writing a 1 to it.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-08-25 18:51:06 -07:00
Timur Tabi dcd83aaff1 tty/powerpc: introduce the ePAPR embedded hypervisor byte channel driver
The ePAPR embedded hypervisor specification provides an API for "byte
channels", which are serial-like virtual devices for sending and receiving
streams of bytes.  This driver provides Linux kernel support for byte
channels via three distinct interfaces:

1) An early-console (udbg) driver.  This provides early console output
through a byte channel.  The byte channel handle must be specified in a
Kconfig option.

2) A normal console driver.  Output is sent to the byte channel designated
for stdout in the device tree.  The console driver is for handling kernel
printk calls.

3) A tty driver, which is used to handle user-space input and output.  The
byte channel used for the console is designated as the default tty.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-23 10:32:56 -07:00
David S. Miller 823dcd2506 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net 2011-08-20 10:39:12 -07:00
Tony Breeds 3b3bceef26 net: fix IBM EMAC driver after rename.
In commit 9aa3283595 (ehea/ibm*: Move the
IBM drivers) the IBM_NEW_EMAC* were renames to IBM_EMAC*

The conversion was incomplete so that even if the driver was added to
the .config it wasn't built, but there were no errors).  In this commit
we also update the various defconfigs that use EMAC to use the new
Kconfig symbol, and explicitly add the NET_VENDOR_IBM guard.

We do not explicitly select the Kconfig dependencies, as this would force
EMAC on.  Doing it in the defconfig allows more flexibility.

Tested on a canyondlands board.

Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-18 21:33:49 -07:00
holt@sgi.com b489da87eb flexcan: Add flexcan device support for p1010rdb.
Allow the p1010 processor to select the flexcan network driver.

Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>,
Acked-by: Wolfgang Grandegger <wg@grandegger.com>,
Cc: U Bhaskar-B22300 <B22300@freescale.com>
Cc: socketcan-core@lists.berlios.de,
Cc: netdev@vger.kernel.org,
Cc: PPC list <linuxppc-dev@lists.ozlabs.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-17 20:36:38 -07:00
holt@sgi.com 243abbf2a6 flexcan: Fix up fsl-flexcan device tree binding.
This patch cleans up the documentation of the device-tree binding for
the Flexcan devices on Freescale's PowerPC and ARM cores. Extra
properties are not used by the driver so we are removing them.

Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>,
Acked-by: Wolfgang Grandegger <wg@grandegger.com>,
Cc: U Bhaskar-B22300 <B22300@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: socketcan-core@lists.berlios.de,
Cc: netdev@vger.kernel.org,
Cc: PPC list <linuxppc-dev@lists.ozlabs.org>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-17 20:36:38 -07:00
Josh Boyer 9fcd768d0c powerpc/40x: Remove obsolete HCU4 board
The HCU4 board is unmaintained.  Remove it.

Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
2011-08-11 13:56:43 -04:00
Ayman El-Khashab e7fa1d1314 powerpc/4xx: enable and fix pcie gen1/gen2 on the 460sx
Adds a register to the config space for the 460sx.  Changes the vc0
detect to a pll detect.  maps configuration space to test the link
status.  changes the setup to enable gen2 devices to operate at gen2
speeds.  fixes mapping that was not correct for the 460sx.  added
bit definitions for the OMRxMSKL registers.  Removed reserved bit
that was set incorrectly in the OMR2MSKL register.

tested on the 460sx eiger and custom board

Signed-off-by: Ayman El-Khashab <ayman@elkhashab.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
2011-08-11 13:51:18 -04:00
Stefan Roese 2f6bab96ef powerpc/44x: Add NOR flash device to Yosemite dts
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
2011-08-11 13:50:42 -04:00
Suzuki Poulose 674bfa4855 powerpc/44x: Kexec support for PPC440X chipsets
This patch adds kexec support for PPC440 based chipsets.  This work is based
on the KEXEC patches for FSL BookE.

The FSL BookE patch and the code flow could be found at the link below:

	http://patchwork.ozlabs.org/patch/49359/

Steps:

1) Invalidate all the TLB entries except the one this code is run from
2) Create a tmp mapping for our code in the other address space and jump to it
3) Invalidate the entry we used
4) Create a 1:1 mapping for 0-2GiB in blocks of 256M
5) Jump to the new 1:1 mapping and invalidate the tmp mapping

I have tested this patches on Ebony, Sequoia boards and Virtex on QEMU.

You need kexec-tools commit e8b7939b1e or newer for ppc440x support, 
available at:

 git://git.kernel.org/pub/scm/utils/kernel/kexec/kexec-tools.git

Signed-off-by: 	Suzuki Poulose <suzuki@in.ibm.com>
Cc:	Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
2011-08-11 13:50:37 -04:00
Benjamin Herrenschmidt a85fe3fce8 powerpc: Really fix build without CONFIG_PCI
Brown paper bag day, previous commit wouldn't work very well with modules
enabled. Move the exports into the ifdef.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-08-11 01:15:44 +10:00
Benjamin Herrenschmidt 81210c2062 powerpc: Fix build without CONFIG_PCI
Commit fea80311a9
"iomap: make IOPORT/PCI mapping functions conditional"

Broke powerpc build without CONFIG_PCI as we would still define
pci_iomap(), which overlaps with the new empty inline in the headers.

Make our implementation conditional on CONFIG_PCI

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-08-05 16:01:20 +10:00
Benjamin Herrenschmidt 883a805d61 powerpc/4xx: Fix build of PCI code on 405
Commit 112d1fe9f7
"powerpc/4xx: Add check_link to struct ppc4xx_pciex_hwops" inadvertently
broke 405 builds due to some functions being over protected by an
ifdef CONFIG_44x.

Move them back out.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-08-05 15:59:40 +10:00
Anton Blanchard 598c8231ab powerpc/pseries: Simplify vpa deregistration functions
The VPA, SLB shadow and DTL degistration functions do not need an
address, so simplify things and remove it.

Also cleanup pseries_kexec_cpu_down a bit by storing the cpu IDs
in local variables.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-08-05 14:47:58 +10:00
Anton Blanchard 711ef84e80 powerpc/pseries: Cleanup VPA registration and deregistration errors
Make the VPA, SLB shadow and DTL registration and deregistration
functions print consistent messages on error. I needed the firmware
error code while chasing a kexec bug but we weren't printing it.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-08-05 14:47:57 +10:00
Anton Blanchard b1301797f3 powerpc/pseries: Fix kexec on recent firmware versions
Recent versions of firmware will fail to unmap the virtual processor
area if we have a dispatch trace log registered. This causes kexec
to fail.

If a trace log is registered this patch unregisters it before the
SLB shadow and virtual processor areas, fixing the problem.

The address argument is ignored by firmware on unregister so we
may as well remove it.

Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-08-05 14:47:57 +10:00
Anton Blanchard 643ba4e307 powerpc: Make KVM_GUEST default to n
KVM_GUEST adds a 1 MB array to the kernel (kvm_tmp) which grew
my kernel enough to cause it to fail to boot.

Dynamically allocating or reducing the size of this array is a
good idea, but in the meantime I think it makes sense to make
KVM_GUEST default to n in order to minimise surprises.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-08-05 14:47:57 +10:00
Nishanth Aravamudan 2c740c5841 powerpc/kvm: Fix build errors with older toolchains
On a box with gcc 4.3.2, I see errors like:

arch/powerpc/kvm/book3s_hv_rmhandlers.S:1254: Error: Unrecognized opcode: stxvd2x
arch/powerpc/kvm/book3s_hv_rmhandlers.S:1316: Error: Unrecognized opcode: lxvd2x

Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-08-05 14:47:56 +10:00
Anton Blanchard 53876e387d powerpc: Lack of ibm,io-events not that important!
The ibm,io-events code is a bit verbose with its error messages.
Reverse the reporting so we only print when we successfully enable
I/O event interrupts.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-08-05 14:47:56 +10:00
Anton Blanchard 8aa6d35929 powerpc: Move kdump default base address to half RMO size on 64bit
We are seeing boot failures on some very large boxes even with
commit b5416ca9f8 (powerpc: Move kdump default base address to
64MB on 64bit).

This patch halves the RMO so both kernels get about the same
amount of RMO memory. On large machines this region will be
at least 256MB, so each kernel will get 128MB.

We cap it at 256MB (small SLB size) since some early allocations need
to be in the bolted SLB region. We could relax this on machines with
1TB SLBs in a future patch.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-08-05 14:47:56 +10:00
David Ahern b59a1bfcc2 powerpc/perf: Disable pagefaults during callchain stack read
Panic observed on an older kernel when collecting call chains for
the context-switch software event:

 [<b0180e00>]rb_erase+0x1b4/0x3e8
 [<b00430f4>]__dequeue_entity+0x50/0xe8
 [<b0043304>]set_next_entity+0x178/0x1bc
 [<b0043440>]pick_next_task_fair+0xb0/0x118
 [<b02ada80>]schedule+0x500/0x614
 [<b02afaa8>]rwsem_down_failed_common+0xf0/0x264
 [<b02afca0>]rwsem_down_read_failed+0x34/0x54
 [<b02aed4c>]down_read+0x3c/0x54
 [<b0023b58>]do_page_fault+0x114/0x5e8
 [<b001e350>]handle_page_fault+0xc/0x80
 [<b0022dec>]perf_callchain+0x224/0x31c
 [<b009ba70>]perf_prepare_sample+0x240/0x2fc
 [<b009d760>]__perf_event_overflow+0x280/0x398
 [<b009d914>]perf_swevent_overflow+0x9c/0x10c
 [<b009db54>]perf_swevent_ctx_event+0x1d0/0x230
 [<b009dc38>]do_perf_sw_event+0x84/0xe4
 [<b009dde8>]perf_sw_event_context_switch+0x150/0x1b4
 [<b009de90>]perf_event_task_sched_out+0x44/0x2d4
 [<b02ad840>]schedule+0x2c0/0x614
 [<b0047dc0>]__cond_resched+0x34/0x90
 [<b02adcc8>]_cond_resched+0x4c/0x68
 [<b00bccf8>]move_page_tables+0xb0/0x418
 [<b00d7ee0>]setup_arg_pages+0x184/0x2a0
 [<b0110914>]load_elf_binary+0x394/0x1208
 [<b00d6e28>]search_binary_handler+0xe0/0x2c4
 [<b00d834c>]do_execve+0x1bc/0x268
 [<b0015394>]sys_execve+0x84/0xc8
 [<b001df10>]ret_from_syscall+0x0/0x3c

A page fault occurred walking the callchain while creating a perf
sample for the context-switch event. To handle the page fault the
mmap_sem is needed, but it is currently held by setup_arg_pages.
(setup_arg_pages calls shift_arg_pages with the mmap_sem held.
shift_arg_pages then calls move_page_tables which has a cond_resched
at the top of its for loop - hitting that cond_resched is what caused
the context switch.)

This is an extension of Anton's proposed patch:
https://lkml.org/lkml/2011/7/24/151
adding case for 32-bit ppc.

Tested on the system that first generated the panic and then again
with latest kernel using a PPC VM. I am not able to test the 64-bit
path - I do not have H/W for it and 64-bit PPC VMs (qemu on Intel)
is horribly slow.

Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-08-05 14:47:56 +10:00
Peter Zijlstra 501d238633 ppc: Remove duplicate definition of PV_POWER7
One definition of PV_POWER7 seems enough to me.

Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-08-05 14:47:55 +10:00
Anton Blanchard bed9a31527 powerpc: pseries: Fix kexec on machines with more than 4TB of RAM
On a box with 8TB of RAM the MMU hashtable is 64GB in size. That
means we have 4G PTEs. pSeries_lpar_hptab_clear was using a signed
int to store the index which will overflow at 2G.

Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-08-05 14:47:55 +10:00
Anton Blanchard c113a3aee2 powerpc: Jump label misalignment causes oops at boot
I hit an oops at boot on the first instruction of timer_cpu_notify:

NIP [c000000000722f88] .timer_cpu_notify+0x0/0x388

The code should look like:

c000000000722f78:       eb e9 00 30     ld      r31,48(r9)
c000000000722f7c:       2f bf 00 00     cmpdi   cr7,r31,0
c000000000722f80:       40 9e ff 44     bne+    cr7,c000000000722ec4
c000000000722f84:       4b ff ff 74     b       c000000000722ef8

c000000000722f88 <.timer_cpu_notify>:
c000000000722f88:       7c 08 02 a6     mflr    r0
c000000000722f8c:       2f a4 00 07     cmpdi   cr7,r4,7
c000000000722f90:       fb c1 ff f0     std     r30,-16(r1)
c000000000722f94:       fb 61 ff d8     std     r27,-40(r1)

But the oops output shows:

eb61ffd8 eb81ffe0 eba1ffe8 ebc1fff0 7c0803a6 ebe1fff8 4e800020
00000000 ebe90030 c0000000 00ad0a28 00000000 2fa40007 fbc1fff0 fb61ffd8

So we scribbled over our instructions with c000000000ad0a28, which
is an address inside the jump_table ELF section.

It turns out the jump_table section is only aligned to 8 bytes but
we are aligning our entries within the section to 16 bytes. This
means our entries are offset from the table:

c000000000acd4a8 <__start___jump_table>:
        ...
c000000000ad0a10:       c0 00 00 00     lfs     f0,0(0)
c000000000ad0a14:       00 70 cd 5c     .long 0x70cd5c
c000000000ad0a18:       c0 00 00 00     lfs     f0,0(0)
c000000000ad0a1c:       00 70 cd 90     .long 0x70cd90
c000000000ad0a20:       c0 00 00 00     lfs     f0,0(0)
c000000000ad0a24:       00 ac a4 20     .long 0xaca420

And the jump table sort code gets very confused and writes into the
wrong spot. Remove the alignment, and also remove the padding since
we it saves some space and we shouldn't need it.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-08-05 14:47:55 +10:00
Anton Blanchard fbafd72815 powerpc: Clean up some panic messages in prom_init
Add a newline to the panic messages in make_room. Also fix a
comment that suggested our chunk size is 4Mb. It's 1MB.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-08-05 14:47:55 +10:00
Anton Blanchard 966728dd88 powerpc: Fix device tree claim code
I have a box that fails in OF during boot with:

DEFAULT CATCH!, exception-handler=fff00400
at   %SRR0: 49424d2c4c6f6768   %SRR1: 800000004000b002

ie "IBM,Logh". OF got corrupted with a device tree string.

Looking at make_room and alloc_up, we claim the first chunk (1 MB)
but we never claim any more. mem_end is always set to alloc_top
which is the top of our available address space, guaranteeing we will
never call alloc_up and claim more memory.

Also alloc_up wasn't setting alloc_bottom to the bottom of the
available address space.

This doesn't help the box to boot, but we at least fail with
an obvious error. We could relocate the device tree in a future
patch.

Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-08-05 14:47:54 +10:00
Scott Wood 26ee97672e powerpc: Return the_cpu_ spec from identify_cpu
Commit af9eef3c7b caused cpu_setup to see
the_cpu_spec, rather than the source struct.  However, on 32-bit, the
return value of identify_cpu was being used for feature fixups, and
identify_cpu was returning the source struct.  So if cpu_setup patches
the feature bits, the update won't affect the fixups.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-08-05 14:47:54 +10:00
Scott Wood 326ed6a9bc powerpc: mtspr/mtmsr should take an unsigned long
Add a cast in case the caller passes in a different type, as it would
if mtspr/mtmsr were functions.

Previously, if a 64-bit type was passed in on 32-bit, GCC would bind the
constraint to a pair of registers, and would substitute the first register
in the pair in the asm code.  This corresponds to the upper half of the
64-bit register, which is generally not the desired behavior.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-08-05 14:47:54 +10:00
Len Brown d0e323b470 Merge branch 'apei' into apei-release
Some trivial conflicts due to other various merges
adding to the end of common lists sooner than this one.

	arch/ia64/Kconfig
	arch/powerpc/Kconfig
	arch/x86/Kconfig
	lib/Kconfig
	lib/Makefile

Signed-off-by: Len Brown <len.brown@intel.com>
2011-08-03 11:30:42 -04:00
Huang Ying df013ffb81 Add Kconfig option ARCH_HAVE_NMI_SAFE_CMPXCHG
cmpxchg() is widely used by lockless code, including NMI-safe lockless
code.  But on some architectures, the cmpxchg() implementation is not
NMI-safe, on these architectures the lockless code may need a
spin_trylock_irqsave() based implementation.

This patch adds a Kconfig option: ARCH_HAVE_NMI_SAFE_CMPXCHG, so that
NMI-safe lockless code can depend on it or provide different
implementation according to it.

On many architectures, cmpxchg is only NMI-safe for several specific
operand sizes. So, ARCH_HAVE_NMI_SAFE_CMPXCHG define in this patch
only guarantees cmpxchg is NMI-safe for sizeof(unsigned long).

Signed-off-by: Huang Ying <ying.huang@intel.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Richard Henderson <rth@twiddle.net>
CC: Mikael Starvik <starvik@axis.com>
Acked-by: David Howells <dhowells@redhat.com>
CC: Yoshinori Sato <ysato@users.sourceforge.jp>
CC: Tony Luck <tony.luck@intel.com>
CC: Hirokazu Takata <takata@linux-m32r.org>
CC: Geert Uytterhoeven <geert@linux-m68k.org>
CC: Michal Simek <monstr@monstr.eu>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
CC: Kyle McMartin <kyle@mcmartin.ca>
CC: Martin Schwidefsky <schwidefsky@de.ibm.com>
CC: Chen Liqin <liqin.chen@sunplusct.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Ingo Molnar <mingo@redhat.com>
CC: Chris Zankel <chris@zankel.net>
Signed-off-by: Len Brown <len.brown@intel.com>
2011-08-03 11:12:37 -04:00
Linus Torvalds 3960ef326a Merge branch 'next/cross-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc
* 'next/cross-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
  ARM: Consolidate the clkdev header files
  ARM: set vga memory base at run-time
  ARM: convert PCI defines to variables
  ARM: pci: make pcibios_assign_all_busses use pci_has_flag
  ARM: remove unnecessary mach/hardware.h includes
  pci: move microblaze and powerpc pci flag functions into asm-generic
  powerpc: rename ppc_pci_*_flags to pci_*_flags

Fix up conflicts in arch/microblaze/include/asm/pci-bridge.h
2011-07-26 17:12:10 -07:00
Arun Sharma 7847777a45 atomic: cleanup asm-generic atomic*.h inclusion
After changing all consumers of atomics to include <linux/atomic.h>, we
ran into some compile time errors due to this dependency chain:

linux/atomic.h
  -> asm/atomic.h
    -> asm-generic/atomic-long.h

where atomic-long.h could use funcs defined later in linux/atomic.h
without a prototype.  This patches moves the code that includes
asm-generic/atomic*.h to linux/atomic.h.

Archs that need <asm-generic/atomic64.h> need to select
CONFIG_GENERIC_ATOMIC64 from now on (some of them used to include it
unconditionally).

Compile tested on i386 and x86_64 with allnoconfig.

Signed-off-by: Arun Sharma <asharma@fb.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-07-26 16:49:47 -07:00
Arun Sharma f24219b4e9 atomic: move atomic_add_unless to generic code
This is in preparation for more generic atomic primitives based on
__atomic_add_unless.

Signed-off-by: Arun Sharma <asharma@fb.com>
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-07-26 16:49:47 -07:00
Arun Sharma 60063497a9 atomic: use <linux/atomic.h>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>

Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-07-26 16:49:47 -07:00
Akinobu Mita 148817ba09 asm-generic: add another generic ext2 atomic bitops
The majority of architectures implement ext2 atomic bitops as
test_and_{set,clear}_bit() without spinlock.

This adds this type of generic implementation in ext2-atomic-setbit.h and
use it wherever possible.

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Suggested-by: Andreas Dilger <adilger@dilger.ca>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-07-26 16:49:46 -07:00
Mike Frysinger 0e9a6cb5e6 ptrace: unify show_regs() prototype
[ poleg@redhat.com: no need to declare show_regs() in ptrace.h, sched.h does this ]
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-07-26 16:49:43 -07:00
Linus Torvalds 184475029a Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (99 commits)
  drivers/virt: add missing linux/interrupt.h to fsl_hypervisor.c
  powerpc/85xx: fix mpic configuration in CAMP mode
  powerpc: Copy back TIF flags on return from softirq stack
  powerpc/64: Make server perfmon only built on ppc64 server devices
  powerpc/pseries: Fix hvc_vio.c build due to recent changes
  powerpc: Exporting boot_cpuid_phys
  powerpc: Add CFAR to oops output
  hvc_console: Add kdb support
  powerpc/pseries: Fix hvterm_raw_get_chars to accept < 16 chars, fixing xmon
  powerpc/irq: Quieten irq mapping printks
  powerpc: Enable lockup and hung task detectors in pseries and ppc64 defeconfigs
  powerpc: Add mpt2sas driver to pseries and ppc64 defconfig
  powerpc: Disable IRQs off tracer in ppc64 defconfig
  powerpc: Sync pseries and ppc64 defconfigs
  powerpc/pseries/hvconsole: Fix dropped console output
  hvc_console: Improve tty/console put_chars handling
  powerpc/kdump: Fix timeout in crash_kexec_wait_realmode
  powerpc/mm: Fix output of total_ram.
  powerpc/cpufreq: Add cpufreq driver for Momentum Maple boards
  powerpc: Correct annotations of pmu registration functions
  ...

Fix up trivial Kconfig/Makefile conflicts in arch/powerpc, drivers, and
drivers/cpufreq
2011-07-25 22:59:39 -07:00
Linus Torvalds 45b583b10a Merge 'akpm' patch series
* Merge akpm patch series: (122 commits)
  drivers/connector/cn_proc.c: remove unused local
  Documentation/SubmitChecklist: add RCU debug config options
  reiserfs: use hweight_long()
  reiserfs: use proper little-endian bitops
  pnpacpi: register disabled resources
  drivers/rtc/rtc-tegra.c: properly initialize spinlock
  drivers/rtc/rtc-twl.c: check return value of twl_rtc_write_u8() in twl_rtc_set_time()
  drivers/rtc: add support for Qualcomm PMIC8xxx RTC
  drivers/rtc/rtc-s3c.c: support clock gating
  drivers/rtc/rtc-mpc5121.c: add support for RTC on MPC5200
  init: skip calibration delay if previously done
  misc/eeprom: add eeprom access driver for digsy_mtc board
  misc/eeprom: add driver for microwire 93xx46 EEPROMs
  checkpatch.pl: update $logFunctions
  checkpatch: make utf-8 test --strict
  checkpatch.pl: add ability to ignore various messages
  checkpatch: add a "prefer __aligned" check
  checkpatch: validate signature styles and To: and Cc: lines
  checkpatch: add __rcu as a sparse modifier
  checkpatch: suggest using min_t or max_t
  ...

Did this as a merge because of (trivial) conflicts in
 - Documentation/feature-removal-schedule.txt
 - arch/xtensa/include/asm/uaccess.h
that were just easier to fix up in the merge than in the patch series.
2011-07-25 21:00:19 -07:00
Amerigo Wang c5f41752fd notifiers: sys: move reboot notifiers into reboot.h
It is not necessary to share the same notifier.h.

This patch already moves register_reboot_notifier() and
unregister_reboot_notifier() from kernel/notifier.c to kernel/sys.c.

[amwang@redhat.com: make allyesconfig succeed on ppc64]
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: David Miller <davem@davemloft.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-07-25 20:57:14 -07:00
Linus Torvalds d3ec4844d4 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
  fs: Merge split strings
  treewide: fix potentially dangerous trailing ';' in #defined values/expressions
  uwb: Fix misspelling of neighbourhood in comment
  net, netfilter: Remove redundant goto in ebt_ulog_packet
  trivial: don't touch files that are removed in the staging tree
  lib/vsprintf: replace link to Draft by final RFC number
  doc: Kconfig: `to be' -> `be'
  doc: Kconfig: Typo: square -> squared
  doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
  drivers/net: static should be at beginning of declaration
  drivers/media: static should be at beginning of declaration
  drivers/i2c: static should be at beginning of declaration
  XTENSA: static should be at beginning of declaration
  SH: static should be at beginning of declaration
  MIPS: static should be at beginning of declaration
  ARM: static should be at beginning of declaration
  rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
  Update my e-mail address
  PCIe ASPM: forcedly -> forcibly
  gma500: push through device driver tree
  ...

Fix up trivial conflicts:
 - arch/arm/mach-ep93xx/dma-m2p.c (deleted)
 - drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
 - drivers/net/r8169.c (just context changes)
2011-07-25 13:56:39 -07:00
Linus Torvalds fcda12e7f6 Merge git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
  modpost: Fix modpost's license checking V3
  module: add /sys/module/<name>/uevent files
  module: change attr callbacks to take struct module_kobject
  modules: make arch's use default loader hooks
  modules: add default loader hook implementations
  param: fix return value handling in param_set_*
2011-07-24 09:54:54 -07:00
Linus Torvalds 5fabc487c9 Merge branch 'kvm-updates/3.1' of git://git.kernel.org/pub/scm/virt/kvm/kvm
* 'kvm-updates/3.1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (143 commits)
  KVM: IOMMU: Disable device assignment without interrupt remapping
  KVM: MMU: trace mmio page fault
  KVM: MMU: mmio page fault support
  KVM: MMU: reorganize struct kvm_shadow_walk_iterator
  KVM: MMU: lockless walking shadow page table
  KVM: MMU: do not need atomicly to set/clear spte
  KVM: MMU: introduce the rules to modify shadow page table
  KVM: MMU: abstract some functions to handle fault pfn
  KVM: MMU: filter out the mmio pfn from the fault pfn
  KVM: MMU: remove bypass_guest_pf
  KVM: MMU: split kvm_mmu_free_page
  KVM: MMU: count used shadow pages on prepareing path
  KVM: MMU: rename 'pt_write' to 'emulate'
  KVM: MMU: cleanup for FNAME(fetch)
  KVM: MMU: optimize to handle dirty bit
  KVM: MMU: cache mmio info on page fault path
  KVM: x86: introduce vcpu_mmio_gva_to_gpa to cleanup the code
  KVM: MMU: do not update slot bitmap if spte is nonpresent
  KVM: MMU: fix walking shadow page table
  KVM guest: KVM Steal time registration
  ...
2011-07-24 09:07:03 -07:00
Jonas Bonn 66574cc054 modules: make arch's use default loader hooks
This patch removes all the module loader hook implementations in the
architecture specific code where the functionality is the same as that
now provided by the recently added default hooks.

Signed-off-by: Jonas Bonn <jonas@southpole.se>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2011-07-24 22:06:04 +09:30
Ohad Ben-Cohen e72542191c virtio: expose for non-virtualization users too
virtio has been so far used only in the context of virtualization,
and the virtio Kconfig was sourced directly by the relevant arch
Kconfigs when VIRTUALIZATION was selected.

Now that we start using virtio for inter-processor communications,
we need to source the virtio Kconfig outside of the virtualization
scope too.

Moreover, some architectures might use virtio for both virtualization
and inter-processor communications, so directly sourcing virtio
might yield unexpected results due to conflicting selections.

The simple solution offered by this patch is to always source virtio's
Kconfig in drivers/Kconfig, and remove it from the appropriate arch
Kconfigs. Additionally, a virtio menu entry has been added so virtio
drivers don't show up in the general drivers menu.

This way anyone can use virtio, though it's arguably less accessible
(and neat!) for virtualization users now.

Note: some architectures (mips and sh) seem to have a VIRTUALIZATION
menu merely for sourcing virtio's Kconfig, so that menu is removed too.

Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2011-07-23 16:20:30 +09:30
Linus Torvalds bbd9d6f7fb Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (107 commits)
  vfs: use ERR_CAST for err-ptr tossing in lookup_instantiate_filp
  isofs: Remove global fs lock
  jffs2: fix IN_DELETE_SELF on overwriting rename() killing a directory
  fix IN_DELETE_SELF on overwriting rename() on ramfs et.al.
  mm/truncate.c: fix build for CONFIG_BLOCK not enabled
  fs:update the NOTE of the file_operations structure
  Remove dead code in dget_parent()
  AFS: Fix silly characters in a comment
  switch d_add_ci() to d_splice_alias() in "found negative" case as well
  simplify gfs2_lookup()
  jfs_lookup(): don't bother with . or ..
  get rid of useless dget_parent() in btrfs rename() and link()
  get rid of useless dget_parent() in fs/btrfs/ioctl.c
  fs: push i_mutex and filemap_write_and_wait down into ->fsync() handlers
  drivers: fix up various ->llseek() implementations
  fs: handle SEEK_HOLE/SEEK_DATA properly in all fs's that define their own llseek
  Ext4: handle SEEK_HOLE/SEEK_DATA generically
  Btrfs: implement our own ->llseek
  fs: add SEEK_HOLE and SEEK_DATA flags
  reiserfs: make reiserfs default to barrier=flush
  ...

Fix up trivial conflicts in fs/xfs/linux-2.6/xfs_super.c due to the new
shrinker callout for the inode cache, that clashed with the xfs code to
start the periodic workers later.
2011-07-22 19:02:39 -07:00
Linus Torvalds a99a7d1436 Merge branch 'timers-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'timers-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  mips: Fix i8253 clockevent fallout
  i8253: Cleanup outb/inb magic
  arm: Footbridge: Use common i8253 clockevent
  mips: Use common i8253 clockevent
  x86: Use common i8253 clockevent
  i8253: Create common clockevent implementation
  i8253: Export i8253_lock unconditionally
  pcpskr: MIPS: Make config dependencies finer grained
  pcspkr: Cleanup Kconfig dependencies
  i8253: Move remaining content and delete asm/i8253.h
  i8253: Consolidate definitions of PIT_LATCH
  x86: i8253: Consolidate definitions of global_clock_event
  i8253: Alpha, PowerPC: Remove unused asm/8253pit.h
  alpha: i8253: Cleanup remaining users of i8253pit.h
  i8253: Remove I8253_LOCK config
  i8253: Make pcsp sound driver use the shared i8253_lock
  i8253: Make pcspkr input driver use the shared i8253_lock
  i8253: Consolidate all kernel definitions of i8253_lock
  i8253: Unify all kernel declarations of i8253_lock
  i8253: Create linux/i8253.h and use it in all 8253 related files
2011-07-22 16:51:56 -07:00
Linus Torvalds 4d4abdcb1d Merge branch 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (123 commits)
  perf: Remove the nmi parameter from the oprofile_perf backend
  x86, perf: Make copy_from_user_nmi() a library function
  perf: Remove perf_event_attr::type check
  x86, perf: P4 PMU - Fix typos in comments and style cleanup
  perf tools: Make test use the preset debugfs path
  perf tools: Add automated tests for events parsing
  perf tools: De-opt the parse_events function
  perf script: Fix display of IP address for non-callchain path
  perf tools: Fix endian conversion reading event attr from file header
  perf tools: Add missing 'node' alias to the hw_cache[] array
  perf probe: Support adding probes on offline kernel modules
  perf probe: Add probed module in front of function
  perf probe: Introduce debuginfo to encapsulate dwarf information
  perf-probe: Move dwarf library routines to dwarf-aux.{c, h}
  perf probe: Remove redundant dwarf functions
  perf probe: Move strtailcmp to string.c
  perf probe: Rename DIE_FIND_CB_FOUND to DIE_FIND_CB_END
  tracing/kprobe: Update symbol reference when loading module
  tracing/kprobes: Support module init function probing
  kprobes: Return -ENOENT if probe point doesn't exist
  ...
2011-07-22 16:44:39 -07:00
Linus Torvalds acb41c0f92 Merge branch 'of-pci' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'of-pci' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  pci/of: Consolidate pci_bus_to_OF_node()
  pci/of: Consolidate pci_device_to_OF_node()
  x86/devicetree: Use generic PCI <-> OF matching
  microblaze/pci: Move the remains of pci_32.c to pci-common.c
  microblaze/pci: Remove powermac originated cruft
  pci/of: Match PCI devices to OF nodes dynamically
2011-07-22 14:54:02 -07:00
Linus Torvalds c7c8518498 Merge branch 'gpio/next' of git://git.secretlab.ca/git/linux-2.6
* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6: (61 commits)
  gpio/mxc/mxs: fix build error introduced by the irq_gc_ack() renaming
  mcp23s08: add i2c support
  mcp23s08: isolate spi specific parts
  mcp23s08: get rid of setup/teardown callbacks
  gpio/tegra: dt: add binding for gpio polarity
  mcp23s08: remove unused work queue
  gpio/da9052: remove a redundant assignment for gpio->da9052
  gpio/mxc: add device tree probe support
  ARM: mxc: use ARCH_NR_GPIOS to define gpio number
  gpio/mxc: get rid of the uses of cpu_is_mx()
  gpio/mxc: add missing initialization of basic_mmio_gpio shadow variables
  gpio: Move mpc5200 gpio driver to drivers/gpio
  GPIO: DA9052 GPIO module v3
  gpio/tegra: Use engineering names in DT compatible property
  of/gpio: Add new method for getting gpios under different property names
  gpio/dt: Refine GPIO device tree binding
  gpio/ml-ioh: fix off-by-one for displaying variable i in dev_err
  gpio/pca953x: Deprecate meaningless device-tree bindings
  gpio/pca953x: Remove dynamic platform data pointer
  gpio/pca953x: Fix IRQ support.
  ...
2011-07-22 14:50:57 -07:00
Fabio Baltieri a63e23b932 powerpc/85xx: fix mpic configuration in CAMP mode
Change the string to check for CAMP mode boot on MPC85xx (eg. P2020) to match
the one in the corresponding dts files (p2020rdb_camp_core{0,1}.dts).

Without this fix the mpic is configured as in the SMP boot mode, which causes
the first core to report a protected source interrupt error for devices
of the other core and lock up.

Also add MPIC_SINGLE_DEST_CPU on both P2020 based architectures in CAMP
mode as suggested by Scott Wood. Thanks.

Cc: Scott Wood <scottwood@freescale.com>
Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-22 03:28:29 -05:00
David S. Miller 368940d0a8 net: Fix ppc64 BPF JIT dependencies.
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21 23:26:13 -07:00
Benjamin Herrenschmidt 50d2a4223b powerpc: Copy back TIF flags on return from softirq stack
We already did it for hard IRQs but it looks like we forgot
to do it for softirqs. Without this, we would lose flags
such as TIF_NEED_RESCHED set using current_thread_info()
by something running of a softirq.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-07-22 13:38:58 +10:00
Kumar Gala 5adfd346e4 powerpc/64: Make server perfmon only built on ppc64 server devices
The 64-bit Book-E parts (to date) dont utilize the 'server' class
perfmon.  So building or depending on it makes no sense (and does break
FSL Book-E 64-bit support).  Move the selection of PPC_HAVE_PMU_SUPPORT
to be based on PPC_BOOK3S_64.

Based on a patch from Scott Wood.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-07-22 13:34:30 +10:00